Smeg combined installation manual A 300807 - 2.qxd

INSTALLATION & USER INSTRUCTIONS
ES2000 FREESTANDING ELECTRIC FIRE
ES2000 Electric Stove
All instructions must be handed to the user for
safekeeping.
Revision F - 06/15
1
Section
1.0
2.0
3.0
4.0
5.0
6.0
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
Contents
Important Notes
Installation Requirements
Appliance Data
Unpacking the Appliance
Component Checklist
Operating the Appliance
Page No. Section
2
7.0
3
8.0
3
9.0
3 10.0
3 11.0
3 12.0
13.0
1.0 IMPORTANT NOTES
GB IE
Contents
Page No.
Safety Cut-Out System
4
Maintenance
4
Cleaning
4
Spares
4
Servicing
4
Appliance Dimensions
5
Guarantee - Terms and Conditions
6
IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY
AND RETAINED FOR FUTURE REFERENCE.
When using this electrical appliance, basic precautions should be followed to reduce the risk
of fire, electric shock and injury to person, including the following:
• This heater must be used on an AC supply only and the voltage marked on the heater’s
rating label must correspond to the supply voltage.
• DO NOT switch the appliance on until it is properly installed as described in this
manual.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• The heater must not be located immediately below a socket-outlet.
• DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• WARNING: In order to avoid overheating, do not cover the heater.
• DO NOT use this heater with a programmer, timer, separate remote-control system or
any other device that switches the heater on automatically, since a fire risk exists if the
heater is covered or positioned incorrectly.
• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal
cutout, this appliance must not be supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on and off by the utility.
• Keep furniture, curtains and other fabric material away from the appliance.
• DO NOT leave the appliance unattended during use.
• From time to time, check the cord for damage. Never use the appliance if the cord or any
part of the appliance shows signs of damage.
2
1.0 IMPORTANT NOTES - CONTINUED
GB IE
• DO NOT run the mains cable under carpets, rugs etc.
• DO NOT cover or obstruct the heater in any way. Overheating will result if it is accidentally covered.
• Never immerse the product in water or any other liquids.
• DO NOT use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cool.
• DO NOT clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It
could cause danger to the user or damage to the appliance.
• DO NOT insert or allow foreign objects to enter the inlet or outlet vents as this may
result in electric shock, fire or damage to the appliance.
• DO NOT install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
2.0 INSTALLATION REQUIREMENTS
The appliance is supplied with a pre-wired three pin BS1363 plug (13Amp fuse rated) and 1.6 metres of electrical flex. It is therefore
necessary for a suitable electrical socket to be located within this distance of the appliance and be easily accessible. The stove may be
installed on a combustible or non-combustible floor, however the heater outlet is underneath the stove and certain types of floor covering may be affected by the heat produced by the stove. The ability of the floor covering to withstand the heat produced by the stove
should be ascertained before proceeding with the installation of the stove. If in doubt then the stove should be mounted on a non-combustible hearth or plinth which extends for at least 150mm in front of the stove.This appliance should be positioned on a firm level surface. If the stove is to be sited in a fire surround then the suitability of the surround for use with electrical heaters should be established with the fire surround manufacturer.If fitted into an open draught fireplace, it is advisable to block off the chimney to reduce the
risk of draught through the stove which may cause the safety cut out system in the fan heater to operate.
3.0 APPLIANCE DATA
Supply Voltage and rating power : 220-240V AC 50Hz, 1650 - 1850W
Heating Elements :
2 x 900W
Location :
Indoor use only
4.0 UNPACKING THE APPLIANCE
Fuse Rating :
13 Amp
Lighting :
2 x G9 25W bulb
Supply plug/cord : BS1363/1.6 metres length
Read all the instructions before continuing to unpack or install this appliance. Carefully lift the appliance from the carton. Check
that the contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
5.0 COMPONENT CHECKLIST
QUANTITY
1
1
DESCRIPTION
Stove and heater assembly
User instruction booklet
6.0 OPERATING THE APPLIANCE
Check that the fan outlet is not covered or obstructed in any
way, and ensure the power to the fire is switched on.
The appliance controls are concealed behind a panel on the front
of the heater.
‘a’
Thermostat
‘b’
Fan (without heat)
‘c’
Heat 900W
‘d’
Heat 900W
‘e’
Flame effect on/off
‘a’
‘e’
‘b’
‘c’
‘d’
‘f ’
‘f ’
Flame effect dimmer
Switch ‘e’ turns on the flame effect. Knob ‘f’ controls the brightness of the flame effect. Turn knob ‘f’ until the desired effect is
achieved.
Switch ‘b’ controls the fan function.The fan may be operated without heat, or without the flame effect.With the fan running, switch
‘c’ turns on heat setting 1 (900W), and switch ‘'d' controls heat setting 2 (1800W). The fan must be switched on for the heat settings to work. The fan and heating functions can be operated with or without the flame effect. The appliance is fitted with a thermostat. To adjust the thermostat, turn knob ‘a’ until the desired room temperature is achieved.
3
7.0 SAFETY CUTOUT SYSTEM
GB IE
This product has one non-self-resetting overheat protection device (thermal cut-out) which will activate if the air inlets or outlets are obstructed. For safety reasons the fire will NOT switch on again automatically, the following procedure must be carried
out before the fire can be operated.
NOTE: The visual effect will remain operational if the cutout is activated, only the fan heater is prevented from working.
Switch OFF the appliance at the wall socket or outlet. Leave the fire OFF for a period of no less than 10 minutes, ensuring all
obstructions are removed. Switch the appliance ON at the wall. Ensure the appliance is turned ON at the control switches. If
the fire fails to operate correctly, repeat the above procedure. If an attempt to switch on the appliance is made before the safety cutout has reset, the appliance may cutout for a further period of time. If the sequence has been followed correctly and the
appliance still fails to function, check the fuse in the wall outlet. If this is not the cause, call an electrician or maintenance engineer.
8.0 MAINTENANCE
ALWAYS DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY BEFORE
UNDERTAKING ANY MAINTENANCE.
Excluding lamps and fuses, use only genuine spare parts available from your supplier. Replacement lamps must be of the same
wattage and specification as those stated in Section 3.0 Appliance Data.
Replacing the light bulbs.
1) Disconnect the appliance from the mains.
2) Open the door.
3) Remove the three screws at the front of the decorative fuel bed. Remove the fuel bed clamp.
4) Lift up the decorative fuel bed.
5) Two bulbs are located under the decorative fuel bed.
6) Unscrew and replace the bulb(s) using only G9 25W bulb.
7) Re-assembly is the reverse of removal.
9.0 CLEANING
There is no specific requirement for care of the fire other than a regular cleaning of the general appliance.
The decorative MDF casing is not removable for cleaning. A wipe with a dry cloth is normally sufficient. DO NOT use abrasive
cleaners as they can damage the finish. Brass and silver parts of the fire may be cleaned using a appropriate metal polishes.
10.0 SPARES
Refer to Section 3.0 Appliance Data for lamp and fuse specification. Excluding lamps and fuses, use only genuine manufacturers
spare parts available from your supplier.
11.0 SERVICING
There are no internal user serviceable parts.
Check regularly for security of wall fixings as appropriate. Also check security of supply cable and connections. If the supply cable
becomes damaged, it must be replaced by a service agent or competent person, such as a qualified electrician.
This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse. Should
the fuse require replacing, it must be replaced with a fuse rated at 13 Amp and
approved to BS1362. In the event of the mains plug being removed/ replaced for any
reason, please note : IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
Blue - Neutral
Brown - Live
Green/ Yellow - Earth
As the colours of the wires in the mains lead of this appliance may not correspond
with the colour markings identifying the terminals in your plug, proceed as follows.
The blue wire must be connected to the terminal marked with an N or coloured
black. The brown wire must be connected to the terminal marked with an L or coloured red. The green/yellow wire must be
connected to the earth terminal which is marked with an E or with the earth symbol. WARNING: Never connect live or
neutral wires to the earth terminal of the plug.
NOTE: If a moulded plug is fitted and has to be removed take great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
Refer to Section 3.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available
from your supplier.
4
12.0 APPLIANCE DIMENSIONS
GB IE
540
All dimensions in mm
FIN:
430
290
5
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifications without prior notice.
6