Smeg combined installation manual A 300807 - 2

INSTALLATION & USER INSTRUCTIONS
LED ELECTRIC STOVE
GB IE
MODELS COVERED BY THESE INSTRUCTIONS
EF09-19
LEIRVIK LED ELECTRIC STOVE
DALVIK LED ELECTRIC STOVE
Focal Point Fires
Christchurch, Dorset BH23 2BT
Tel: 01202 588 632
Fax: 01202 499326
www.focalpointfires.co.uk
e : info@focalpointfires.co.uk
*VARIOUS COLOURS AVAILABLE
MODEL SHOWN: LEIRVIK LED ELECTRIC STOVE
Questions or problems with your appliance?
Don’t take it back to the store
just give us a call on 01202 588601 we’re here to help
lines open between 9am and 5pm, Monday to Friday
Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not permitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.
All instructions must be handed to the user for
safekeeping.
Revision A - 07/16
1
© 2016 Focal Point Fires plc.
Section
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
Contents
Important Notes
Installation Requirements
Appliance Data
Unpacking the Appliance
Component Checklist
Installing the Appliance
Operating the Appliance
Safety Cutout System
Page No. Section
2
9.0
3 10.0
3 11.0
3 12.0
3 13.0
3 14.0
4 15.0
5
1.0 IMPORTANT NOTES
GB IE
Contents
Page No.
Maintenance
5
Cleaning
5
Spares
5
Servicing
6
Appliance Dimensions
6
Troubleshooting Guide
7
Guarantee - Terms and Conditions
7
IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY
AND RETAINED FOR FUTURE REFERENCE.
When using this electrical appliance, basic precautions should be followed to reduce the risk
of fire, electric shock and injury to person, including the following:
• This heater must be used on an AC supply only and the voltage marked on the heater’s
rating label must correspond to the supply voltage.
• DO NOT switch the appliance on until it is properly installed as described in this
manual.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• The heater must not be located immediately below a socket-outlet.
• DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• WARNING: In order to avoid overheating, do not cover the heater.
• DO NOT use this heater with a programmer, timer, separate remote-control system or
any other device that switches the heater on automatically, since a fire risk exists if the
heater is covered or positioned incorrectly.
• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal
cutout, this appliance must not be supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on and off by the utility.
• Keep furniture, curtains and other fabric material away from the appliance.
• DO NOT leave the appliance unattended during use.
• From time to time, check the cord for damage. Never use the appliance if the cord or any
part of the appliance shows signs of damage.
2
© 2016 Focal Point Fires plc.
1.0 IMPORTANT NOTES - CONTINUED
GB IE
• DO NOT run the mains cable under carpets, rugs etc.
• DO NOT cover or obstruct the heater in any way. Overheating will result if it is accidentally covered.
• Never immerse the product in water or any other liquids.
• DO NOT use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cool.
• DO NOT clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It
could cause danger to the user or damage to the appliance.
• DO NOT insert or allow foreign objects to enter the inlet or outlet vents as this may
result in electric shock, fire or damage to the appliance.
• DO NOT install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
2.0 INSTALLATION REQUIREMENTS
The appliance is supplied with a pre-wired three pin BS1363 plug (13Amp fuse rated) and 1.8 metres of electrical flex. It is therefore
necessary for a suitable electrical socket to be located within this distance of the appliance and be easily accessible. The stove may be
installed on a combustible or non-combustible floor, however the heater outlet is underneath the stove and certain types of floor covering may be affected by the heat produced by the stove. The ability of the floor covering to withstand the heat produced by the stove
should be ascertained before proceeding with the installation of the stove. If in doubt then the stove should be mounted on a non-combustible hearth or plinth which extends at least 150mm in front of the stove.This appliance should be positioned on a firm level surface.
If the stove is to be sited in a fire surround then the suitability of the surround for use with electrical heaters should be established with
the fire surround manufacturer.If fitted into an open draught fireplace, it is advisable to block off the chimney to reduce the risk of
draught through the stove which may cause the safety cut out system in the fan heater to operate.
3.0 APPLIANCE DATA
Supply Voltage and rating power : 220-240V AC 50Hz, 1500 - 1800W
Heating Elements :
1500 - 1800W
Location :
Indoor use only
4.0 UNPACKING THE APPLIANCE
Fuse Rating :
13 Amp
Lighting :
LED Light Strip
Supply plug/cord : BS1363/1.8 metres length
Read all the instructions before continuing to unpack or install this appliance. Carefully lift the appliance from the carton. Check
that the contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
5.0 COMPONENT CHECKLIST
QUANTITY
1
1
1
2
DESCRIPTION
Heater main body with decorative castings
Instruction booklet
Remote control handset
Levelling feet
6.0 INSTALLING THE APPLIANCE
CAUTION: DO NOT CONNECT THE APPLIANCE TO THE ELECTRICAL SUPPLY AT THIS TIME
Situate the LED stove in the desired location. If the surface is uneven, fit two levelling feet behind the two front cast legs. Unscrew in a anti
clockwise orientation to extend the feet and clockwise to contract the front legs. The fires levelness can be checked by using a spirit level.
Before finally fitting the appliance into its location, ensure that the mains cable and plug are properly routed.
3
© 2016 Focal Point Fires plc.
7.0 OPERATING THE APPLIANCE
GB IE
Read All Instructions Before Use
Check that the heater outlet grille, mounted beneath the appliance, is not covered or obstructed in anyway, and ensure the power
to the fire is switched on.
Control Panel
The control panel is located underneath the grill at the top of the appliance.This panel contains the buttons to properly operate the
electric fireplace.
1. 2. 3. 4.
1. Main Power Button
2. Flames Control Button
3.
1.
3. Heater Control Button
4.Timer Control Button
2.
5.Temperature Control Buttons (Remote Control Only)
5.
4.
Remote Control
The fire is supplied with an IR multifunction remote.
The remote control has an effective range of up to 13 feet.
Before the remote will operate the plastic insulating sheet needs
to be removed.
Battery Replacement
Battery Requirements: 3V CR2025
1. Locate and remove the battery bracket.
2.The battery has two sides, one with a button feature, and the
other is flat.
3. Insert the battery with the button side down into the battery
bracket, making sure the battery is firmly seated.
Using The Main Power Button
The main power button (1) is located on the control panel under the grill on top the of the appliance. Pressing the main power button
(1) once turns the power ON.
Pressing the main power button (1) again will turn the power OFF.
If you find that none of the other buttons appear to work, check to make sure that the main power (1) is turned on.
Battery Disposal
Batteries must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area.
Using the Flames Control Button
Press the flames control button (2) to turn on the ember bed
and flame effect.
Pressing the flames control button (2) once turns flames on and
lights the ember bed.
Pressing the flames control button (2) again will cycle through different colours of the ember bed.The colour rotation mode will
cycle through the 3 different colour settings continuously. Refer
to the table opposite for more detailed information.
Using the Heater Control Button
The heater control button (3) turns the heater on and off.With the unit
ON, press the control panel heater button (3) for 5 seconds and enter
temperature adjustment mode.
Hold button (2) down for five seconds to change from Fahrenheit to
Celsius.
Press the control panel heater button (3) to change to the desired temperature.There are 10 temperature settings. Refer the table opposite
for more detailed information.
After the temperature is selected, it will stay on for 10 seconds, then
turn off.
4
© 2016 Focal Point Fires plc.
7.0 OPERATING THE APPLIANCE - CONTINUED
Using the Timer Control Button
Pressing the timer control button (4) will set the timer.
GB IE
NOTE: If this product experiences exceptionally
high temperature, it may automatically stop heating. If this
occurs the product should be unplugged or isolated from the
main supply for a period of 30 seconds before the power is
then re-supplied.
8.0 SAFETY CUTOUT SYSTEM
This product has a non-self-resetting overheat protection device (thermal cut-out) which will activate if the air inlets or outlets
are obstructed. For safety reasons the fire will NOT switch on again automatically, the following procedure must be carried out
before the fire can be operated.
NOTE: The visual effect will remain operational if the cutout is activated, only the fan heater is prevented from working.
Switch OFF the appliance at the wall socket or outlet. Leave the fire OFF for a period of no less than 10 minutes, ensuring all
obstructions are removed. Switch the appliance ON at the wall. Ensure the appliance is turned ON at the control switches. If
the fire fails to operate correctly, repeat the above procedure. If an attempt to switch on the appliance is made before the safety cutout has reset, the appliance may cutout for a further period of time. If the sequence has been followed correctly and the
appliance still fails to function, check the fuse in the wall outlet. If this is not the cause, call an electrician or maintenance engineer.
9.0 MAINTENANCE
ALWAYS DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY BEFORE
UNDERTAKING ANY MAINTENANCE.
Excluding lamps and fuses, use only genuine spare parts available from your supplier. Replacement lamps must be of the same
wattage and specification as those stated in Section 3.0 Appliance Data.
10.0 CLEANING
ALWAYS DISCONNECT THE APPLIANCE AT THE SUPPLY OUTLET SOCKET BEFORE UNDERTAKING
ANY CLEANING.
Except for periodic cleaning of dust, there are no specific requirements for care, other than regular cleaning of the general
appliance. A wipe with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Make
sure the heater outlet grille (located under the stove), and the air inlet mesh grilles (located on the rear of the stove) are kept
clear of dust, pet hair and other airborne household matter. These should be vacuum cleaned periodically using a brush attachment.
GLASS PANEL - This should only be cleaned using a suitable glass cleaner. Test on a small area first.
11.0 SPARES
Refer to Section 3.0 Appliance Data for lamp and fuse specification. Excluding lamps and fuses, use only genuine manufacturers
spare parts available from your supplier.
5
© 2016 Focal Point Fires plc.
12.0 SERVICING
GB IE
There are no internal user serviceable parts.
Also check security of supply cable and connections. If the supply cable becomes damaged, it must be replaced by a service agent
or competent person, such as a qualified electrician.
This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse. Should
the fuse require replacing, it must be replaced with a fuse rated at 13 Amp and
approved to BS1362. In the event of the mains plug being removed/ replaced for any
reason, please note : IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
Blue - Neutral
Brown - Live
Green/ Yellow - Earth
As the colours of the wires in the mains lead of this appliance may not correspond
with the colour markings identifying the terminals in your plug, proceed as follows.
The blue wire must be connected to the terminal marked with an N or coloured
black. The brown wire must be connected to the terminal marked with an L or coloured red. The green/yellow wire must be
connected to the earth terminal which is marked with an E or with the earth symbol. WARNING: Never connect live or
neutral wires to the earth terminal of the plug.
NOTE: If a moulded plug is fitted and has to be removed take great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
Refer to Section 3.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available
from your supplier.
13.0 APPLIANCE DIMENSIONS
All dimensions in mm
6
© 2016 Focal Point Fires plc.
14.0 TROUBLESHOOTING GUIDE
Fire is not switching on
Fire is not emitting any heat
Fire shuts off after a period of time
GB IE
Ensure mains switch is on
Replace the fuse in the plug
The fire is fitted with an energy saving thermostat. If the temperature in the room
is higher than the temperature selected on the fire, then the thermostat will stop
the heater from turning on. For example, if the room temperature is 22ºc or above
and the fires heater is set at 22ºc, then the heater will not be required until the
room temperature drops below 22ºc. If this is the case select a higher temperature
setting than the room’s temperature and the heater will begin to operate.
Check that the temperature is not set onto the lower settings. If the room is
warm enough the thermostat will stop the fire switching the heat on.
Check that the chimney/flue is blocked off.
Fire seems noisy
Remote is not operating
Clean inlet and outlets out with a vacuum cleaner.
There is a level of noise when the flame effect is in use, caused by a motor that
helps generate the effect. This noise will be heard when there is no other
background noise.
There is a higher level of noise associated with the heater motor; this is due to
the air flow required when heat has been selected.
Check or replace batteries.
15.0 GUARANTEE - TERMS AND CONDITIONS
The 3 year guarantee only covers products purchased on or after 1st February 2009. For all gas fires purchased the 3 year guarantee
commences from the date of purchase, provided that the following 3 terms and conditions are adhered to:
Registration is not required.
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your proof
of purchase.
2. Your gas fire must have been commissioned by a Gas Safe registered installer, evidence of which you must provide together with
theGas Safe registration number.
3. Your appliance must have been serviced annually, irrespective of use, by a Gas Safe registered installer, evidence of which must be
provided, such as the receipt.
Please note all consumable items such as any ceramics including; coals, pebbles, the matrix, front strips, side cheeks, rear panels and
tapered rear panels are not covered by the 3 year guarantee.For all Electric fires purchased the 3 year guarantee commences from
the date of purchase, providing that you can supply the proof of purchase. This does not cover consumable items such as pebbles,
coals or light bulbs.
Making a claim is easy.
If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then please
submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you can email or
fax.Please note that this does not affect your statutory rights.
Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.
Alternatively email: 3g@focalpointfires.co.uk or fax. 01202 499326.
F861370
Details required:
1. Name, full address including post code and contact telephone number.
2. Receipt of purchase or credit card statement.
3. Original installers CORGI/Gas Safe* registration number (gas fires only).
4. Annual service receipt for every 12 months (gas fires only).
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifications without prior notice.
7
© 2016 Focal Point Fires plc.
Download PDF