INSTRUCTIONS FOR USE WM75.2 Washing machine W6098X

INSTRUCTIONS FOR USE
WM75.2
Carefully read the instructions for use before using the washing machine.
Washing machine
W6098X
Dear Customer,
We thank you for purchasing this quality ASKO product.
We hope it meets all your expectations. Scandinavian design combines pure lines, everyday functionality,
and high quality. These are the key characteristics of all our products, and the reason why they are highly
appreciated across the globe.
We kindly recommend you to read these instructions before using the appliance for the first time. The
instruction manual also includes information on how you can help protect the environment.
TABLE OF CONTENTS
Safety precautions
3
Cleaning and maintenance
35
Washing machine description
6
Errors – what to do?
40
Dispenser tray
6
Service
45
Before using the appliance for the first time
7
Technical information
46
Installation and connection
9
Program table
48
Tips before washing
13
Table: washing mode/temperature
50
Washing process, step by step (1 – 8)
15
Table options
51
System settings
27
Disposal
52
Special features
31
Quick guide
55
The following symbols are used throughout the manual and they have the following meanings:
Information, advice, tip, or recommendation
Warning – danger of hot surface
Warning – general danger
Warning – danger of fire
Warning – danger of electric shock
Original instructions
2
See Quick guide on the last page.
SAFETY PRECAUTIONS
GENERAL
Please read the instruction manual and save it for future reference.
• Please do not use the washing machine if you have not read and
understood these instructions or use first.
• Failure to observe the instructions for use or inappropriate use of the
washing machine may result in damage to the laundry or machine, or injury
to the user. Keep the instruction manual handy, near the washing machine.
• Instructions for use are available on our website at www.asko.com.
• Your washing machine is intended solely for household use.
• The appliance has to be connected to the water and power supply by a
trained expert.
• Any repair and maintenance pertaining to safety or performance should be
done by trained experts.
• To avoid hazard, damaged power cord may only be replaced by the
manufacturer, authorized service technician, or other authorized person.
• After installation, the washing machine should stand still for two hours before
it is connected to the power mains.
• The washing machine may not be connected to the power mains using an
extension cord.
• Do not connect the washing machine to an electrical outlet intended for an
electric shaver or hair dryer.
• To connect the washing machine to water supply, make sure to use the
supplied water supply hose and gaskets. Water pressure has to be between
0.1 and 1 MPa (approximately 1–10 kp/cm2, 1-10 bar, 10–100 N/cm2).
• Always use a new water supply hose to connect the appliance to water
supply; do not reuse an old water supply hose.
• After the washing cycle, close the water tap and pull out the washing
machine plug from the power socket.
• Only use the washing machine for washing laundry, as described in the
instruction manual. The machine is not intended for dry cleaning.
• In case of incorrect appliance connection, incorrect use, or servicing by an
unauthorized person, the user shall bear the cost of any damage.
• Only use detergents intended for the washing machine!
• Only use agents for machine washing and care of laundry. We shall not be
responsible for any damages or discolouration of gaskets and plastic parts
resulting from incorrect use of bleaching or colouring agents.
3
• Bleaches that contain chlorine can be replaced with oxygen-based bleaches.
Otherwise, a neutralization cycle should be performed by running the Cotton
program at the highest temperature. For best results, use hydrogen peroxide
or oxygen-based detergents.
• Do not use colourants (dyes) or bleaching substances (substances
for discolouration or removal of colourants) as they contain sulphuric
compounds that could cause corrosion.
• Excessive use of products containing chlorine compounds increases the
risk of premature failure of appliance components. This depends on the
concentration of chlorine, exposure time, and temperature.
•
Do not use detergents that contain solvents as this could lead to release
of poisonous gases, damage to the machine, and risk of fire and explosion.
• Before using the appliance for the first time, remove the transport bolts and
all other transport protection devices. See chapter "BEFORE FIRST USE /
Transport protection".
• The machine is not intended for use by persons (including children) with
physical or mental impairments, or persons with lacking experience and
knowledge. These persons should be instructed about the use of the
appliance by a person responsible for their safety.
• Emergency door opening tool is located on the back side of the dispenser.
• Maximum washing capacity in kg (for the label program Standard cotton) is
indicated on the rating plate (or in the PROGRAM TABLE).
CHILD SAFETY
• Do not allow small children to play with the washing machine.
• Before closing the washing machine door and running the program, make
sure there is nothing except laundry in the drum (e.g. if a child climbed into
the washing machine drum and closed the door from the inside).
• Keep the detergent and conditioner out of reach of children.
• Activate the child lock. See chapter "SYSTEM SETTINGS, section Child
Lock".
• Do not let children younger than three years to come near the
appliance, unless they are under constant supervision.
• The washing machine is made in compliance with all relevant safety
standards. This washing machine may be used by children aged 8 years and
above and by persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge, but only if they are supervised during
the use of the appliance, if they have been provided relevant instructions
regarding safe use of the washing machine, and if they understand the
4
hazards of inappropriate use. Make sure children do not play with the
appliance. Make sure the children do not clean the washing machine or
perform any maintenance tasks without supervision.
DANGER OF HOT SURFACE
• At higher washing temperatures, the door glass will heat up. Be careful to
avoid burns. Make sure children do not play near the door glass.
WATER OVERFLOW PROTECTION
• If the water level in the appliance rises above the normal level, then the
excessive water level protection will be activated. It will shut off the water
supply and start pumping out the water. If the water level does not decrease
in 60 seconds, the program will be interrupted (see chapter "ERRORS –
WHAT TO DO?").
TRANSPORTING / STORAGE DURING THE WINTER
If you transport or store the appliance in vehicles or rooms that are not heated
and where the temperature could drop to below freezing point, please do the
following:
• Clean the drain pump filter. See chapter "CLEANING AND MAINTENANCE".
• Close the water supply to the washing machine, undo the water supply hose
from the water supply tap, and wait until the water flows out of the tap and the
hose.
• After the drain pump filter is emptied, there can still be a small amount of
water in the machine. This, however, does not affect the quality and will not
damage the appliance.
• If the washing machine is to be transported, transport protection has
to be re-installed before transport (See chapter "BEFORE USING THE
APPLIANCE FOR THE FIRST TIME").
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE!
5
WASHING MACHINE DESCRIPTION
87 6
9
1 2
3
1.
2.
3.
4.
5.
6.
7.
Main switch (ON/OFF)
Program selector knob
Display unit
Program settings buttons
Button (start/pause)
Dispenser tray
QR and AUID code (on the inside of the washing
machine door)
8. Rating plate with information about the washing
machine (on the inside of the washing machine
door)
9. Washing machine door
10. Drain filter cover
11. Water release hose
12. Drain filter pump (installed behind the drain
pump filter)
4 5
10 11 12
DISPENSER TRAY
1. Prewash compartment
2. Compartment for main wash liquid
detergent.
Use the foldable barrier (3).
7
3
1
4
6
2. Compartment for main wash powder
detergent.
Do not use the foldable barrier (3).
5
4. Softener / conditioner compartment
2
5. Compartment (A) for liquid detergent for
the Color program for the ADS.
(ADS = Auto Dose System);
6. Compartment (B) for liquid detergent
for the Black / White / Sensitive / Other
program for ADS
7. Tab for dispenser tray removal
6
BEFORE USING THE APPLIANCE FOR THE FIRST TIME
PACKAGING
Remove all packaging.
Please sort the materials in compliance with local recommendations (see chapter ”DISPOSAL”).
TRANSPORT PROTECTION
Before using the appliance, remove the three transport bolts and plastic plugs which protect the appliance
during transport.
1
2
3
1
Release and remove the bolts as shown in the
figures.
2
To remove the plastic plugs holding the bolts,
squeeze them and then pull them out.
Remove the caps from the plastic plugs. Push the
caps over the three holes in which the plastic plugs
were inserted. Save the bolts and plastic plugs if you
have to transport your washing machine in the future.
3
If you wish to transport the washing machine, reinstall the bolts and plastic caps to lock the machine. This
will prevent any damage to the machine due to vibrations during transport. If you have lost the transport bolts
or plastic caps, replacements can be ordered at your dealer.
Art. No.
ID:
270698
Bolt
551188
Plastic cap (transport lock)
Please order three pieces of each item!
7
CLEANING
Disconnect the washing machine from the power mains and open the door. Clean the washing machine drum
with a damp cloth and a mild detergent.
Connect the washing machine to the power mains and run the dedicated drum cleaning program. See
chapter "WASHING PROCESS; STEP BY STEP (1–8)" /STEP 5: CHOOSE THE PROGRAM.
No program can be started while the door is open.
SETTINGS BEFORE FIRST USE
After connecting the washing machine and power it for the first time, you will be asked to do following
settings:
1. Language selection
Use the Program selector knob or buttons to scroll the list of languages.
Confirm the selection by pressing the "Set" button.
2. Water hardness
The following water hardness settings are available: soft / normal / hard.
Table for water hardness; See chapter "SYSTEM SETTINGS/WATER HARDNESS".
Confirm your selection with the button under the selected water hardness.
Press the "Next" button to confirm your selection.
For further washing process, see chapter "WASHING PROCESS; STEP BY STEP (1–8)".
The amount of detergent also depends on the hardness of water. For details, see the detergent
packaging. Please contact your local water supply company to check the water hardness in your area.
In models with ADS the amount of detergent dispensed also depends on the water hardness setting.
Before using the AD system for the first time, run one of the programs (without any laundry), after filling
the A or B tank with liquid detergent (see chapter ”SPECIAL FEATURES”).
Before the product is dispatched from the factory, every appliance is tested.
As a result, there may be some residual water left in the discharge pump filter. This, however, does not affect
the quality and will not damage the appliance.
8
INSTALLATION AND CONNECTION
POSITIONING THE WASHING MACHINE
Opening the washing machine door (top view)
Before connecting the washing machine to the
power mains, wait for at least 2 hours until it reaches
room temperature.
978 mm
The washing machine can be installed as a builtin (integrated) or a free-standing unit. Place the
machine on a level surface so that the power outlet
on the wall is accessible.
Free-standing appliance
If you have a dryer of suitable dimensions (by
another dryer manufacturer), use the vacuum feet
to stack it on top of the washing machine, or place it
next to it.
412 mm
Built-in washing machine
The washing machine can be integrated under a
worktop with a height of 900–950 mm. Leave 5
cm of room around the entire appliance, including
between the back edge of the upper cover and the
wall behind it.
0°
11
Stacking an ASKO dryer on top of an ASKO
washing machine
To stack an ASKO dryer on top of a washing
machine, use the extra vacuum feet and the tipping
guard (A+B), supplied in the cardboard box in the
ASKO dryer drum. If the washing machine and
dryer are not of matching dimensions or if you
have installed a hidden helper between the two
appliances, then binding plates are available as
optional accessories at the service unit.
A
B
Clearances around the washing machine
min. 50 mm
min. 50 mm
min. 50 mm
9
ADJUSTING THE FEET
CONNECTING TO WATER SUPPLY
Place the washing machine so that it is stable.
1. Level the washing machine in longitudinal and
traverse direction by rotating the adjustable feet
(using a No. 32 spanner).
The feet allow levelling by +/- 1 cm.
2. When the appropriate height of feet is set, use the
wrench No. 17 to firmly fasten the counter-nuts
towards the bottom of the appliance
.
3. Tighten the jam nuts (counter nuts) to the end
position.
This will reduce washing machine noise, vibration,
movement etc. to minimum.
The machine has to be connected to water
supply by an adequately trained person.
Use the water supply hose to connect the appliance.
Water pressure has to be between 0.1 and 1 MPa
(approximately 1–10 kp/cm2, 1-10 bar, 10–100 N/
cm2).
If the hoses are newly installed, we recommend
rinsing them to remove any impurities. Otherwise,
these impurities could clog the filter in the water
connection on the washing machine and thus cut off
the water supply.
1
2
3
The water intake hose has to be fastened firmly
enough for the hose to have a good seal.
After connecting the hose, the seal must be checked
for any leaks.
Only use the water supply hose supplied with the
appliance. Do not use any used or other hoses.
If the connection on the supply hose is of
different dimensions than the water tap (e.g. 3/4” →
1/2”), use an adapter.
10
CONNECTING TO HOT/COLD WATER
SUPPLY
INSTALLING THE DRAIN HOSE
(Only available in some models)
If your appliance has connections for both hot
and cold water, then connect one hose to the cold
water connection and the other hose to the hot
water connection, as indicated on the back of the
appliance:
COLD = cold and HOT = hot.
Hot water is supplied for programs operating at 40
°C or more.
Connecting to both hot and cold water will save
time and electric energy when washing.
Upon delivery, the appliance has a drain hose
attached. This drain hose must be connected to
a drain. Drain hose can also be attached to a wall
drain with a trap; such trap should be properly
installed to allow cleaning. The height of the drain
should be 600–900 mm above the floor. The lower
position (600 mm) is always recommended. Make
sure the drain hose is not clipped or bent.
A
C
600 - 900 mm
600 - 900 mm
B
600 - 900 mm
If your washing machine model has connections
for both hot and cold water, and you only wish to
connect cold water, then the protective cap has to be
(or remain) attached to the hot water connection.
Drain hose can also be connected directly to the
washbasin drain via a siphon. In this case, the hose,
should be 600–900 mm above the floor. Internal
hose diameter should be at least 18 mm.
See figure.
At least 18 mm
11
CONNECTING TO THE POWER MAINS
After installation, the washing machine should
stand still for two hours before it is connected to the
power mains.
Connect the appliance to an earthed power outlet.
After installation, the wall outlet should be freely
accessible. The outlet should be fitted with an earth
contact (in compliance with the relevant regulations).
Connection upon delivery
TYPE: WMXX.XXXXX MODEL: XXXXXX.X
Art.No.: XXXXXX/XX
Ser.No.: XXXXXXXX
XXX-XXX V ~ XXXX W
IPX4
XX Hz
XXA
X kg
XX-X MPa
Information about your washing machine is indicated
on the rating (type) plate.
Use the type A differential current protection switch.
We recommend using over-voltage protection to
protect the appliance in case of a lightning strike.
The washing machine may not be connected to
the power mains using an extension cord.
Do not connect the washing machine to an
electrical outlet intended for an electric shaver or
hair dryer.
Any repair and maintenance pertaining to safety
or performance should be done by trained experts.
12
TIPS BEFORE WASHING
This chapter includes several tips on how to prepare
the laundry for washing.
LAUNDRY SYMBOLS
Observe the laundry symbols.
Textile maintenance symbols:
LAUNDRY SORTING
Sort the laundry according to:
• how soiled it is,
• colour,
• material.
Washing
Normal
CLOTHING
1. Close the zips and hook-and-loop fasteners so
that they do not damage the fabric.
2. New dyed items may contain excess dye;
therefore, they have to be washed separately
several times.
3. Turn delicate items inside out. This will decrease
the risk of tear and colour fading.
4. Place very sensitive clothes and small items in a
special-purpose laundry washing bag.
(The special purpose laundry bag is available as
an optional accessory.)
5. Empty the pockets and turn them inside out.
Delicate
Max. washing temperature 90 °C
Max. washing temperature 60 °C
Max. washing temperature 40 °C
Max. washing temperature 30 °C
Hand wash only
Do not wash
Bleaching
c1
Bleaching in cool water
Bleaching not allowed
Dry cleaning
A
Dry cleaning with all agents
P
Perchloroethylene R11, R113, petroleum
F
Dry cleaning in kerosene, pure alcohol,
and R113
Dry cleaning not allowed
Ironing
Ironing with a hot iron with a maximum
temperature of 200 °C
Ironing with a hot iron with a maximum
temperature of 150°C
Ironing with a warm iron with a maximum
temperature of 110°C
Ironing not allowed
Natural drying
Drying on a flat surface
Drying without prior spinning
Drying on a clothes line or a hanger
Tumble drying
Drying at high temperatures
Drying at low temperatures
Tumble drying not allowed
13
DYED COTTON
ECONOMY AND EFFICIENCY
Laundry made of dyed cotton which is to be washed
at 60 °C should be first washed at a temperature of
60 °C to remove the excess dye. If this is not done,
there is danger of dye being washed out of such
items. To maintain the colour of the fabric, use
bleach-free detergent.
You can save a lot of energy by not using the
programs operating at higher temperatures.
Choose the Quick program if you wish to only
refresh the laundry; or use the Time program. This
will save water and power.
Selecting the maximum spinning speed will reduce
power consumption if you dry the clothes in a
dryer or a drying cabinet.
When using the programs Heavy, Everyday Wash
and Standard Cotton, we recommend washing a full
load.
Avoid prewash. Modern washing machines and
detergents are efficient without the prewash as well.
Prewash is only necessary for heavily soiled
laundry. Use the additional function Prewash (see
"STEP 6: Program Settings Menu – choosing extra
functions / button 5").
UNBLEACHED LINEN
Unbleached lining fabric should be washed at
60 °C with a detergent free of bleach or optical
bleaching agents. Heavily soiled linen laundry may
be occasionally washed at higher temperatures, but
do not do this too often as heat could ruin the sheen
and strength of linen clothing.
WOOL
These fabrics are intended for either machine or
hand wash. The Wool/Hand Wash program is
equally gentle or even gentler than an actual hand
wash.
Wool in particular is sensitive to washing and similar
procedures.
If you do not wish to spin your clothes, select a
setting without spinning (see "STEP 6: Choose
the program settings /button 3"). However, most
garments are suitable for at least a short spinning
cycle. Top spinning speed available is 800 rpm.
DETERGENTS
Detergents carrying the environment protection label
are less harmful to the environment.
Only add the detergents in compliance with the
recommendations by detergent manufacturers.
Recommended amount of washing detergent
at certain loads and water hardness levels are
specified on the detergent packaging.
STAINS
VISCOSE AND SYNTHETIC FIBRES
Materials made of viscose and some synthetic fibres
are highly sensitive, and require a lot of space in
order not to crease. When washing, only fill the
drum to a half and choose a program with spinning
speed of no more than 1,000 rpm.
If your clothes are soiled with stubborn stains
(blood, eggs, coffee, grass etc.), they should be
appropriately treated before the wash. Then, wash
your laundry using the special programs (if your
washing machine has them).
Do not use any chemical substances or agents;
only use the stain removing detergents.
Viscose and acetates are fragile when wet.
DYEING FABRICS
REDUCING ALLERGIC REACTIONS
(Only in some models)
The options include washing with the Allergy
Program Cotton and Allergy Program Synthetics,
using the Allergy Mode program setting, or using an
extra rinse (Super Rinse). These programs, program
settings, and functions can be used for people
with sensitive skin, such as those suffering from
allergies, or small children.
SAVING TIME AND ENERGY
To save time and energy, use the Everyday Wash.
This program has shorter main wash cycle than
Standard Cotton and often suffices for less soiled
laundry.
If you wish to dye fabrics in the washing machine,
choose the Everyday Wash program with the Super
Rinse extra function. Choose the temperature
according to the dye manufacturer's
recommendations. If you dye mixed fabrics, such
as polyester/cotton, choose a low spinning speed.
Add the dye directly into the drum, rather than
in the detergent compartment. After dyeing use
the Drum Cleaning program (self-cleaning program).
Use the standard amount of detergent.
When using bleaches or stain removal agents,
there is danger of corrosion and discolouration.
To protect the environment, we advise against
using powerful chemicals.
14
WASHING PROCESS, STEP BY STEP (1 – 8)
STEP 1: SORT THE LAUNDRY
See chapter "TIPS BEFORE WASHING"
Use a washing net for underwire bras. Empty the pockets. Coins, nails etc. could damage the machine
and the fabric.
STEP 2: TURN ON THE MAIN SWITCH.
Turning on
Press the
on/off button.
Turning off
Press the
on/off button.
If the machine does not accept the on/off command correctly, wait for at least 8 seconds before pressing any
other button.
STEP 3: OPEN THE WASHING MACHINE DOOR AND INSERT THE LAUNDRY.
Open the washing machine door by pulling the handle towards you.
1
2
3
Place the laundry into the washing machine drum.
Before doing so, make sure the drum is empty.
Do not overload the drum!
If the washing machine drum is too full, the laundry will not be washed as thoroughly.
15
STEP 4: ADD THE DETERGENT AND THE CONDITIONER.
Recommended amount of detergent is usually specified on the detergent packaging. When washing a
smaller amount of laundry, the amount of detergent used can be decreased.
Observe manufacturers' recommendations regarding the type of detergent suitable for certain temperatures,
load size, and water hardness.
When using the ADS (AutoDoseSystem), the appliance will automatically add the liquid detergent depending
on the amount and type of laundry.
Powder detergent
Add powder detergent into the main wash detergent compartment. If you have selected the Prewash function
or Heavy program, Stain program Coffee or Fruit, or the Time program with 2:30 or longer duration, then add
powder detergent to the prewash detergent compartment.
We recommend adding the powder detergent immediately before the washing cycle. Otherwise, make
sure the detergent compartment in the dispenser tray is completely dry before adding the powder detergent,
as otherwise, the powder detergent may cake before the start of the washing process.
Liquid detergent
When using a liquid detergent, observe the detergent manufacturer's recommendations. When using thick
detergents, we recommend always using the laundry balls. Use the barrier (3) in the detergent compartment;
see figure in the chapter detergent tray. Add the liquid detergent in the front part of the detergent
compartment in the dispenser tray (2).
Liquid detergent in ADS
The washing machine will automatically add the amount of liquid detergent according to the amount of your
laundry and depending on how heavily soiled it is. Before adding the liquid detergent, pull out the dosing
container as far as it will go.
Compartment (A) for liquid detergent for the Colour program.
Compartment (B) for liquid detergent for the Black / White / Sensitive / Other program.
See chapter "SPECIAL FEATURES".
The washing machine must be switched on before you add the detergent!
Laundry ball or washing bag
If you are using a laundry ball or a washing bag, place it directly into the drum and choose a program without
any prewash.
An excessive amount of detergent will not improve washing results. Rather, it will lead to foaming and
increase the environmental impact. We recommend using less detergent. Only increase the dosage if you are
not satisfied with the washing results.
Conditioner
Pour the conditioner into the dispenser tray, into the compartment with the symbol
recommendation on the conditioner packaging.
. Observe the
Do not fill the conditioner compartment over the max. indication (maximum indicated level). Otherwise, the
conditioner will be added to the laundry too soon, leading to poorer washing effect.
16
STEP 5: CHOOSE THE PROGRAM.
Choose the program by rotating Program selector knob in either direction. Confirm the program selection by
pressing the button under the program.
Choose the program depending on the type of laundry and how heavily soiled it is (see chapter "TIPS
BEFORE WASHING").
Estimated program duration will appear on the display.
Extra program settings can also be selected for each program.
See STEP 6.
Choose between the following programs:
Program
Description
1.
EVERYDAY WASH
Program for lightly to moderately dirty laundry. The temperature can
be set separately; therefore, observe the instructions indicated on the
clothing. Wash the clothes worn directly on the skin at 60 °C. Less
heavily soiled laundry will be thoroughly cleaned at 40 °C. Spinning
speed can also be freely selected. Default setting is maximum spinning
speed.
Program duration and amount of water will be adjusted to the amount of
laundry.
2.
STANDARD COTTON
Program for normally or heavily soiled laundry, white or coloured. The
temperature can be set separately; therefore, observe the instructions
indicated on the clothing worn directly on the skin. Choose 40 °C if
the laundry is only lightly dirty. Spinning speed can be set to your
preference. Default setting is maximum spinning speed.
Program duration and amount of water will be adjusted to the amount of
laundry.
3.
MIX/SYNTHETICS
Program for delicate clothing made of synthetic and mixed fibres
or viscose, and for simple care of cotton. The highest available
temperature is 60 °C. Observe the instructions indicated on the clothing.
Most synthetic fabrics will be washed at 40 °C. Clothing worn directly on
the skin should be washed at 60 °C. Maximum spinning speed is 1000
rpm; it can be decreased if necessary.
4.
WOOL/HAND
Gentle program for washing wool, silk, and clothes that require manual
washing. Maximum temperature is 40 °C. This program has a short
spinning cycle. Top spinning speed available is 800 rpm.
5.
DARK WASH
This program is used for washing dark laundry using special-purpose
detergents for black laundry. The program washes at low temperatures,
with gentle tumbling and lower spin speed.
17
Program
18
Description
6.
TIME PROGRAM
Use this program when you wish to wash the laundry for a specific
amount of time. Duration can be set from 20 minutes to 3 hours (in
15-minute steps). In this program, select the corresponding washing
time and temperature according to the type of laundry being washed.
7.
AUTO
This program automatically adjusts the duration of the main wash and
number of rinses depending on the amount of laundry in the machine.
No extra program settings are possible.
8.
QUICK
Quick program for laundry that only needs refreshing. The program
operates at certain temperatures; therefore, observe the instructions
indicated on the clothing. A lower temperature setting will result in
shorter duration of the wash. Spinning speed can be set to your
preference.
9.
HEAVY
Program for heavily soiled laundry. The temperature can be set
separately; therefore, observe the instructions indicated on the clothing.
Maximum available temperature is 90 °C. It is suitable for very heavily
soiled laundry.
Spinning speed can be set to your preference.
Program duration and amount of water will be adjusted to the amount of
laundry.
10.
RINSE
This program includes 2 cold rinses and a short spinning cycle. The
program is suitable for laundry that only needs rinsing, and for cleaning
cloths or mops.
11.
SPIN
Use the program when you only wish to spin the laundry.
12.
DRAIN
If you only wish to pump out the water from the washing machine,
choose the Drain program.
13.
EASY CARE
Program for delicate clothing made of synthetic and mixed fibres, and
for simple care of cotton. It may also be used for pillows, quilted jackets
and similar items, as it uses a lot of water for the wash. Carefully read
the washing instructions. If the outer layer has a membrane, do not
use a conditioner. Washing temperature can be set up to 60 °C, and
spinning speed can be set up to 1000 rpm.
14.
DRUM CLEANING
This program is used to clean the drum and to remove detergent
residues and bacteria. The drum has to be empty. Only add a small
amount of powder detergent. You may also add a small amount of
vinegar (approximately 2 dl) or sodium bicarbonate “baking soda” (1
tablespoon or 15 g). Run this program at least once a month.
15.
JEANS
Program for washing jeans. It uses low temperature and a low spin
speed. Due to a higher water level and an extra rinse, there will be no
traces of detergent on the jeans.
16.
SHIRTS
This program washes the collars and cuffs without wrinkling them. The
wash takes place at a low temperature, with a greater amount of water
and gentle tumbling.
Program
Description
17.
HYGIENE
This program is used to wash clothes that require special care, such
as baby clothes , undreware or clothes for people suffering from skin
allergies.
We recommend turning the garments inside out as this will also
thoroughly wash out the skin residues or residues of skin treatment
products.
The program is a combination of an extra long and high heating and
extra rinsing with strong and sharp movements that removes any
detergent residue.
18.
SPORTS WEAR
This program is suitable for washing clothing with membranes,
waterproof clothing, and breathable clothing, requiring simple care. It
is suitable for sportswear made of mixed materials. It combines low
temperature with gentle tumbling.
Do not use conditioner with this program!
19. B
CONDITIONING
This is short program suitable for washing waterproof clothes and
clothing made of microfibres.
This is short program suitable for washing waterproof clothes , if agent
is used, and clothing made of microfibres.
The program makes sure the clothes are waterproof and reduces
adherence of dirt on the outer surface of the garments.
Use of an impregnation agent is recommended.
The program combines a short wash with cold water and gentle
tumbling.
20.
STAIN PROGRAM
Choose the fabric and stain type from the menu, and the right stain
removal program will be automatically selected.
You can choose between the following types of stains: red wine, blood,
grass, blueberries, butter/grease, chocolate, coffee/tea, egg, dairy
products, kids, baby.
After selecting the type of stain, select the type of fabric (Cotton or
Synthetics) and washing temperature for the selected type of fabric.
See chapter "TIPS BEFORE WASHING".
You can also choose the spinning rate.
21.
BEDDING
This program is used to wash bedding, pillows, and larger items.
Weekly wash of your bedding will remove skin residue and mites.
Observe the instructions for washing and maintenance. The wash uses
a large amount of water and extra rinse cycles.
22.
ALLERGY COTTON
This program is used to wash normal to heavily soiled clothes that
require special care, such as clothes for people with highly sensitive
skin or skin allergies. We recommend turning the garments inside out
as this will also thoroughly wash out the skin and other residues.
You can also select the option to wash at maximum temperature and
maximum spinning speed.
Set temperature will be maintained for a longer time period than on
conventional programs in combination with intense agitation and extra
rinses.
23.
ALLERGY
SYNTHETICS
This program is used to wash clothes that require special care, such
as clothes for people with highly sensitive skin or skin allergies. The
program is also suitable for people sensitive to washing detergents. We
recommend turning the garments inside out as this will also thoroughly
wash out the skin and other residues.
Set temperature will be maintained for a longer time period than on
conventional programs in combination with intense agitation and extra
rinses.
19
Program
Description
24.
QUICK
A quick program with high efficiency for smaller amounts of lightly
soiled laundry. The program washes with intensive tumbling and lower
spin speed.
(4 kg, 40 °C, 59 min)
25.
SYSTEM SETTINGS
Use the program selector knob to choose System Settings and confirm
with ENTER (button "2").
Use the Program selector knob to scroll through the settings.
The following options are available:
– Child Lock,
– Language (language selection),
– Temperature (temperature unit),
– Automatic Dosing System (ADS),
– Water (water hardness),
– Sounds (acoustic signals),
– Display (display unit: brightness & logo),
– Programs (set of programs),
– Reset.
See chapter "SYSTEM SETTINGS".
20
STEP 6: CHOOSING THE PROGRAM SETTINGS
Using the program settings, the washing programs can be further adjusted to your wishes.
Some program settings may not be available for your selected program.
Selected program settings will remain stored after the end of the washing cycle and may be changed
subsequently (except for delayed start which is not stored after the wash is complete).
1
1. Washing program (that you selected)
2. Washing mode
3. Temperature
2
3
4
5
6
4. Spin speed)
5. Start delay
6. Additional program option (choosing extra
functions)
Choose the program settings before pressing the START button.
Program settings cannot be changed during the progress of a program.
Press the button under the program setting to display the information (INFO) about the each program
setting.
Following are the program settings that may be selected using the buttons 2 to 6:
2. Washing mode
The following washing modes are available:
•
Normal mode
(Basic setting)
Green mode
•
(Wash that saves energy; longer washing time, lower water consumption).
•
Speed Mode
(Time-saving wash; shorter washing times, higher water and energy consumption).
In the Cotton program, we recommend a half-load.
•
Allergy Mode
(Wash with extra water, extra rinsing, extended washing time, higher water and energy consumption)
•
Night Mode
(Wash that reduces noise and extends washing time.)
•
Intense Mode
(Wash that improves cleaning performance, with extra water and extended washing time).
3. Temperature
The following temperatures are available for the selected program:
Cold wash and 20/30/40/50/60/70/80/90 °C.
The actual available temperature options will depend on the selected program.
21
4. Spin speed
The following spinning rates are available for the selected program: max. (rpm) /... / NO d (no drain) (max rpm
= depends on the model).
Default setting is 1400 rpm; it depends on the selected program (spin rate can be changed – reduced or
increased (only in some models)).
The actual available spin speed will depend on the selected washing program.
With the NO d (no drain) option, the program will not include a spin cycle, and the water from the last rinse
will remain in the washing machine. The laundry will stay in the water from the last rinse, which will prevent
creasing. If you have selected the No d (No Drain) option, you have to select the Drain or Spinning program
after the end of the washing program to pump the water out from the machine before you open the washing
machine door.
5.
Start delay
Choose the delayed start when you wish the washing program to start after a certain period of time (30´ to 24
hours after you press the Start button).
Use the Program selector knob to
Set Delay Start
set the delay from 30´ to 4 hours in
30 Min
1h
1,5 h
2h
2,5 h
OFF
30-minute steps, and then from 6 hours
to 24 hours in 1-hour steps.
Press the button to confirm your
selection.
2:00 h + 1:42 h The estimated start delay time and time
Everyday wash
Program
Mode
40°C
1000
Temp
Spin
2h
OptioStart
ns
Delay
1:30 h
Delay
/
Options
remaining until the end of the washing
program will be indicated above the 6
button. When the countdown reaches
zero, the selected washing program will
start automatically.
To change the start delay time, press the Pause button and then use the 5 button or the Program selector
knob to set a new start delay time. After selecting the new delay time, press the Start button again.
To cancel or skip the delay and start the washing process immediately, press the 5 button (Skip).
If you have set the delayed start function and you are using liquid detergent, we do not recommend
choosing a programme with a pre-wash cycle.
22
6.
Selecting extra functions (Options)
Press the button to confirm the extra settings. Then, use the Program selector knob to scroll the list of
functions or options. Confirm your selection by pressing the button under the selected function or option.
The following extra functions are available:
*
Favourite programs
To store the selected program as a favourite, press the
button and the program with all your settings will
be stored.
The stored program will be displayed at the start of the Main menu.
Up to 6 favourite programs can be stored.
If you do not wish to store the program after the wash, rotate the Program selector knob and you will return to
the program selection; or, simply open the washing machine door.
Changing a favourite program
If you wish to store a program after the end of the washing cycle, but there is no more room for another
favourite program (only 6 favourite program slots are available), then one of the existing stored favourite
programs can be substituted with a new one.
The list of favourite programs will appear when you switch on the washing machine.
*
Super Rinse (extra rinses) (depending on model)
To increase the number of rinse cycles (+2), select the Super Rinse setting. This is recommended for persons
with highly sensitive skin and/or in areas with very soft water. Confirm the selection by pressing the On
/
Off
button.
Use the
button to return to Main menu.
*
Prewash
To use a prewash before the main wash, choose the Prewash option. Use of this function is recommended for
heavily soiled laundry or for laundry with stubborn surface stains. Confirm the selection by pressing the On
/ Off
button.
Use the
button to return to Main menu.
Add the prewash detergent into the prewash compartment
and the main wash detergent into the main
wash compartment
of the dispenser tray (see chapter "DISPENSER TRAY").
*
High water level
For a larger amount of water after the wash and spinning cycle, select the High Water Level option. Confirm
the selection by pressing the On
/ Off
button.
Use the
button to return to Main menu.
Anti-crease
*
To prevent creasing the wash, choose the Anti-Crease option (gently tumbling). This function is
recommended for delicate laundry. Confirm the selection by pressing the On
/ Off
button.
Use the
button to return to Main menu.
Some functions may not be available on all programs.
23
STEP 7: START THE WASH
Close the washing machine door and press the Start
/Pause button.
Start (short press of the button – start/resume)
Pause (short press of the button – pause)
Stop (press and hold for 3 seconds – stop or cancel)
40°C
01:34
Starting
Everyday
Remaining time
Depending on the selected program, anticipated washing time will be displayed in hours and minutes.
Actual washing time will depend on the selected program, load, type of laundry, spin speed etc.
Actual washing time may be longer or shorter than initially displayed.
Remaining time will be updated during the program duration, depending on the actual amount of laundry
and amount of water pumped into the machine. The last remaining time update takes place before the final
spinning cycle.
In case of uneven distribution of laundry, the time on the display will flash and it will not count down.
Once the laundry is evenly redistributed, the washing time will continue and it will stop flashing.
40°C
00:26
Washing
Everyday
Adding or removing laundry after the start of the program
Everyday
wash
Everyday
40°C
ECO
Program
Everyday
PROGRAM
Mode
MODE
1:42 h
1000
40o°C
40
C
Paused 1000
Temp
TEMP
Spin
SPIN
OFF
O
iD
on
A
utpotClothes
ose
Add
OPTIONS
1:30
1:30 hh
01:41
Delay
/ /
Options
Stop
Program
DELAY
5
40°C
Please wait
Everyday
24
01:41
To add or remove laundry during the
progress of a washing program, use
the Start/Pause
button to pause the
program. Then, press the button 5 to
select "Add clothes".
The door may be opened when the water is pumped from the machine (but not completely pumped out).
Then, add or remove the laundry. Close the door and continue the program. Press the Start /Pause button.
The program will resume from the point at which it was interrupted.
If the door cannot be opened, it is
40°C
possible that the temperature in the
Door unlocked
01:41 machine is too high, and you won't be
Everyday
Stop Program
able to add the laundry.
Also, if the door cannot be opened, it
is possible that the program has been
running for too long and any laundry
added at that point would not be
efficiently washed.
Pausing, stopping or changing the program
40°C
Ready to resume
Everyday
01:41
Stop Program
To pause the program, shortly press the
Start/Pause
button.
To resume a program, press the Start
/Pause button again.
40°C
Resuming wash
01:40
Everyday
To stop the washing program, press the Start/Pause button and hold it for 3 seconds.
Choose "Stop program". The program is canceled and the water is pumped out of the machine if necessary.
Only then will you be able to open the washing machine door. Use the Program selector knob to select a new
program. If necessary, add detergent, and then press the Start /Pause button.
A washing program can be paused by pressing the ON/OFF button.
The washing machine will switch off.
After the washing machine is switched on, press the Start button to resume the program.
Do not open the dispenser tray while the appliance is operating.
25
STEP 8: END OF PROGRAM
40°C
Wash finished
00:00
Wash finished
00:00
Everyday
After the end of the washing program,
the display will indicate that the program
has been successfully completed
("Wash finished").
40°C
A
Auto
40°C
A
Auto
Wash finished
Stop Anti Crease
If you have selected the Anti-Crease
extra function, gentle tumbling will
continue after the end of the washing
program in order to prevent creasing.
6
Open the door towards you and remove the laundry from the washing machine.
Make sure the washing machine drum is empty.
If you do not take any action within 5 minutes after the end of the program, the display will switch off to
standby mode in order to save power.
The display will light up again if you press the ON/OFF button or open the washing machine door.
After the washing cycle, close the water intake and pull out the washing machine plug from the power
socket.
26
SYSTEM SETTINGS
40°C
Stain program
60°C
60°C
60°C
40°C
Bedding
Allergy Cotton
Allergy Synth.
Quick PRO
Settings
In the Main menu, use the Program
selector knob to select System Settings.
Confirm the selection by pressing the
button under the desired setting.
6
Then, use the Program selector knob to scroll the list of the following settings that you can adjust:
Child Lock
°C / °F
•
•
•
•
•
•
•
•
•
Child Lock,
Language (language selection),
Temperature (temperature unit),
Automatic Dosing System (ADS),
Water (water hardness),
Sounds (acoustic signals),
Display: brightness & logo
Programs (set of programs),
Reset.
Use the button
to return to System Settings or to the Main menu.
Press the button under the setting to display concise information about the setting.
CHILD LOCK
Select Child Lock with the
Child Lock
button.
°C / °F
Child Safe Start
Choose between switching the child
lock On or Off.
When the child lock is activated, no
other function can be selected.
onds in order to activate/deactivate the child lock
On
1
4
5
6
To temporarily (for 3 minutes) switch off
the Child lock, press the 1 and 4 buttons
simultaneously and keep them pressed
for 3 seconds.
Use the
menu.
button to return to Main
27
LANGUAGE
You can choose between 25 languages.
Press the
button. Use the Program
selector knob to scroll the list of
languages.
Confirm your selection by pressing the
"Set" button.
Set language to: United Kingdom ENGLISH
Use the
menu.
button to return to Main
°C / F TEMPERATURE (TEMPERATURE UNIT)
Choose either °C or °F.
Confirm your selection with the button
under the selected temperature unit.
Set Temperature Unit
°C / F
°C
°F
Use the
menu.
button to return to Main
AUTOMATIC DOSING SYSTEM (ADS)
Press the ON/OFF button to switch on/off the ADS display in the Main menu.
For ADS settings, see chapter "SPECIAL
Auto Dose
FEATURES".
28
On
Off
A
60°C
40°C
40°C
30°C
40°C
Auto Dose
Everyday wash
Cotton
Mix / Synth
Wool / Hand
Dark
60°C
40°C
40°C
30°C
40°C
30°C
Everyday wash
Cotton
Mix / Synth
Wool / Hand
Dark
Time
ON = display the ADS menu in the Main
Menu
OFF = do not display the ADS menu in
the Main Menu
Use the
menu.
button to return to Main
WATER (WATER HARDNESS)
Set Water Hardness
Normal
Soft
Hard
Choose water hardness between the
following settings: soft / normal / hard.
Confirm your selection with the button
under the selected water hardness.
Use the
menu.
button to return to Main
Water hardness can be measured with a water hardness indicator (available in a pharmacy). Check the
information on water hardness with your local water supply company or authority.
Water
hardness
Hardness levels
°dH (°N)
m mol/l
°fH(°F)
p.p.m.
1 – soft
< 8,4
< 1,5
< 15
< 150
2 – normal
8,4 - 14
1,5 - 2,5
15 - 25
150 - 250
3 – hard
> 14
> 2,5
> 25
> 250
SOUNDS
You may choose the acoustic signal
volume.
Sounds Settings
Volume
Sound Volume
+
Use the (–/+) button to set the acoustic
signal volume.
During selection, the acoustic signal will
be played with the currently highlighted
volume.
Use the
menu.
button to return to Main
29
DISPLAY UNIT
Set the brightness and logo display.
Display Settings
Brightness
Info
Logo
Brightness
Use the (–/+) buttons to set the display
brightness.
+
Logo
Confirm your selection with the button
under the logo display on/off option.
ON = display the logo at turning washing
machine on
OFF = not display the logo at turning
washing machine on
Use the
menu.
button to return to Main
PROGRAMS
The Main menu includes the entire set of programs that you can choose using the Program selector knob.
This setting allows only displaying the selected program in the Main menu.
Use the Program selector knob to select
Customize Favorites and Programs
2
3
1
30
40
40
40
40
a program.
Confirm your selection with the button
A
under the selected program.
Auto
Everyday
Cotton
Mix / Synth
Wool / Hand
Symbol
will appear next to the
selected program.
°C
°C
°C
°C
°C
Customize Favorites and Programs
1
40°C
Everyday
2
40°C
Cotton
30°C
Mix / Synth
40°C
Wool / Hand
30°C
Dark
Only programs indicated with
appear on the display unit.
Use the
menu.
.will
button to return to Main
RESET
This means that all settings will return to the default settings and your own settings will be deleted.
Confirm the selection by pressing the
Reset Washing Machine Settings?
button under the "reset" option that will
appear on the display.
Reset default
Use the
menu.
30
button to return to Main
SPECIAL FEATURES
AUTOMATIC DOSING SYSTEM (ADS)
1.
2.
3.
4.
ADS display in the Main menu (see chapter "SYSTEM SETTINGS")
Choosing the ADS settings in the Main menu
Filling the ADS tank
Choosing the ADS settings by opening the dispenser tray
2. Choosing the ADS settings in the Main menu
A
60°C
40°C
40°C
30°C
40°C
Auto Dose
Everyday wash
Cotton
Mix / Synth
Wool / Hand
Dark
Set the automatic dosing by pressing
the button under the ADS.
With this setting, you will choose which tank (A or B) the detergent will be dispensed from.
Automatic liquid detergent dosing
3
46
Auto Dose
B
A
system can be set for each washing
cycle separately.
Dirt
Options
The most recent setting is stored and
it can be changed for the next washing
cycle.
In some programs the ADS setting is not
available.
A
B
C
D
Press the A/B button and hold if for a
while to display information about the
content of the A/B tank.
A, B. Choose the compartment from which the detergent is to be added depending on the type of laundry.
You can choose between automatic detergent dosing from compartment A or from compartment B. Confirm
the setting with
Liquid detergent for Colour
A
Liquid detergent for Black / White / Sensitive / Other. See section D/e (choosing the type of laundry).
B
C. Choose how heavily soiled the laundry is. Choose between:
Lightly soiled laundry
Normally soiled laundry
Heavily soiled laundry
The washing program will choose the suitable amount of detergent depending on the setting for how heavily
the laundry is soiled.
31
D. Press the Options button to set the following:
Auto Dose Options
Set ML/Wash
for A
Set ML/Wash
for B
a
b
Rinse
tank A
c
Rinse
tank B
d
Content
tank B
e
a, b. Amount of liquid detergent (ml/cycle from the compartment, A or B. Choose the amount of detergent
according to liquid detergent manufacturer's recommendations specified on the packaging. For thus washing
machine model, observe the recommendations for 4–6 kg loads, medium water hardness and medium-soiled
laundry. The washing machine's factory setting is 60 ml. This amount shall be adjusted depending on the
water hardness setting, load sensed by the washing machine, and how heavily the laundry is soiled.
Auto Dose Options
Set ML/Wash
for A
Set ML/Wash
for B
a
b
Rinse
tank A
Rinse
tank B
Content
tank B
40
50
60
Rinse
tank A
Rinse
tank B
Content
tank B
Set concentration for new detergent A (ml/wash)
10
20
30
c, d. Cleaning the detergent tank
Select Options, then choose Rinse.
Auto Dose Options
Set ML/Wash
for A
Set ML/Wash
for B
c
d
We recommend cleaning the detergent tank once per two months and when it is empty.
Before cleaning the detergent tank, close the dispenser tray.
Rinse tank B
Pumping out detergent. Please wait.
Cancel
Rinse tank B
Tank B successfully emptied.
Next
32
The compartment may be additionally rinsed with an extra amount of water via detergent compartment
inlet. (500 ml of water). Open the dispenser tray to the final position and add water to the compartment to be
cleaned. Then, close the dispenser tray and press the Start button (maximum amount of detergent that
can be added to selected detergent tank is 1.5 l)
If you do not wish to rinse the tank with
Rinse tank B
water, the process can be cancelled by
of water and close compartment.
pressing
button.
If you have already started supplying
the water, the process can no longer be
cancelled. The
sign will disappear
and the water filling process has to be
completed.
When cleaning of compartment B is completed, open the dispenser tray to the end position and pour the
liquid detergent into compartment B.
Rinse tank B
detergent in compartment B.
Ok
6
Cleaning time for a full tank (draining + rinsing) may be up to 60 minutes.
e. Type of detergent, and changing the detergent in the ADS
The detergent in the compartment A shall only be used for one type of laundry: coloured wash (Colour).
The detergent in compartment B shall be designated for several types of laundry.
Set content tank B
Black
White
Sensitive
Other
When you change the detergent in the tank B, select another type of laundry. The question whether you are
sure you wish to change the detergent will appear on the display unit.
We recommend changing the detergent when the detergent tray is empty.
Otherwise, the compartment has to be emptied. In this case, however, the dispenser tray has to be
closed first.
Pour the other type of liquid detergent into compartment B (e.g. if you have selected Black, you will probably
add the special detergent for black laundry).
If the compartment is not empty, then the liquid detergent should be pumped out from the compartment
and the compartment should be cleaned (see section c, d. "Cleaning the compartments").
33
3. Filling the compartment with liquid detergent
Before adding the liquid detergent into the tank, pull out the dispenser tray as far as it will go.
(If the dispenser tray is not fully opened, the liquid detergent will not flow into the tank.)
The washing machine has to be switched on.
Start adding the liquid detergent to the selected compartment. The level for the selected compartment,
indicated on the display unit, will increase. When the compartment is full, stop adding the detergent.
(maximum amount of detergent that can be added to selected compartment is 1.5 l).
Tank B is full
The maximum level for Auto Dose tank B has been reached.
Ok
Before closing the dosing tank, wait for 10 seconds to let the detergent flow into the compartment.
If you add too much liquid detergent, it may overflow into the washing machine drum. To remove the detergent
from the drum, use the Rinse program.
Start rinse program if you want to remove detergent from drum.
Ok
4. Choosing the ADS settings by opening the dispenser tray
Pull out the dispenser tray as far as it will go, to its end position! The ADS setting in the Main Menu will be
displayed.
All steps are the same as with section 2 (Choosing the ADS settings in the Main menu).
If you selected OFF in the System Settings (i.e. do not display the ADS menu in the Main Menu), then the
ADS menu will not be displayed when you open the dispenser tray.
Only add liquid detergents into the ADS tanks.
Do not mix liquid detergent with conditioner. Do not add conditioner into any ADS tank; conditioner has to
be added manually to the compartment labelled with .
Do not mix different liquid detergents. Before changing the liquid detergent (depending on the type of
laundry), the tanks have to be cleaned. See sections c, d. Cleaning the tanks.
34
CLEANING AND MAINTENANCE
CLEANING THE FILTER
The washing machine has a filter that will retain smaller objects such as coins, buttons, hair etc.
Before cleaning, drain the water from the washing
machine using the Drain program, and disconnect
the washing machine from the power mains.
1
Open the pump filter cover using appropriate tools
(emergency door opening tool is located on the back
side of the dispenser).
2
Release the water drain hose from the holder.
Before cleaning the filter, drain the water from the
washing machine by placing the end of the water drain
hose over a large shallow container and opening the
cap on the water drain hose.
3
Gradually rotate the filter in the counter-clockwise
direction and pull it out.
4
Clean the filter thoroughly under running water.
5
Remove all objects and impurities from the filter
housing and the impeller.
Replace the filter as shown in the figure and
fasten it by rotating in the clockwise direction. For
a good seal, the filter seal surface should be clean.
Also re-install the drain hose.
6
35
CLEANING THE DISPENSER TRAY AND DOOR RUBBER GASKET
1
A
B
Press the tab to completely remove the dispenser
tray from its housing.
Rinse and thoroughly clean the tray. You may also
remove the cap from the plug in the conditioner
compartment (A). Clean any residue from the cap and
tube.
2
Clean the dispenser tray (B) interior.
Replace the cap on the plug.
3
Use a brush to clean the nozzles on the upper
side of the dispenser tray housing.
After a washing program, nozzles that clean the
interior of the dispenser are automatically switched on
(only available in some models).
Use a brush to clean the lower part of the dispenser
tray housing.
4
Replace the detergent dispenser into its housing.
Close the dispenser tray!
Do not wash the dispenser tray in the dishwasher!
5
36
After every wash, wipe the rubber door seal to
extend its useful life.
CLEANING THE AUTOMATIC DOSING SYSTEM (ADS)
Cleaning the detergent compartment:
Remove the dispenser tray from the dispenser
housing by pulling it out and pressing the release
tab (1).
1
1
2
Open the cover for detergent compartment A and B
(2).
2
Rinse the detergent compartment by directing a
stream of running water through it.
37
CLEANING THE APPLIANCE EXTERIOR
Wipe the washing machine exterior and the display unit using a soft damp cotton cloth and mild detergent.
Do not use any solvents or cleaning agents that could damage the washing machine (please observe
the recommendations and warnings provided by the manufacturers of the cleaning agents).
Do not clean the washing machine with a jet of water!
Always disconnect the washing machine from the power mains before cleaning.
CLEANING THE WASHING MACHINE INTERIOR AGAINST ODOURS
Modern detergents often allow washing clothes at low temperatures. This means that residue may
accumulate in the washing machine, which in turn could cause odours.
To avoid such odorous, we recommend running the self-cleaning program (Drum-cleaning) once per month.
Use a small amount of powder detergent and do not put any laundry in the drum.
38
CLEANING THE RINSING HOLES (UNDER THE AGITATOR IN THE DRUM)
If you believe that objects like nails or paper clips fell into the washing machine drum, check the area
underneath the agitator. Such objects may rust (corrode) and cause stains on your clothes. Nails and other
sharp objects can also cause holes in the fabric.
Proceed as follows:
1
Insert a screwdriver or a similar tool into the slot in
the rib and carefully push it to the left.
2
Hold the rib with the other hand and pull it towards
you.
3
4
Lift the drum rib.
Remove any objects.
Place the rib into the installation slot indicated with
"F" towards you. Make sure all ribs are firmly in
place in their respective slots in the drum. Push the rib
inwards (as indicated by the arrow in the figure) until it
snaps.
5
If you are using hard water
If you are washing with hard water (causing limescale build-up), a greyish-white film may appear on the
washing machine drum. To remove this film, add vinegar (approximately 2 dl or sodium bicarbonate “baking
soda” (1 tablespoon or 15 g)) into the washing machine drum and select any program with a temperature of
90 °C, or the Drum Cleaning program. See STEP 5: Choose the program.
Repeat the process as necessary.
Water hardness can be set under "SYSTEM SETTINGS / Water / Water Hardness".
39
ERRORS – WHAT TO DO?
Disturbances from the environment (e.g. the power grid) may result in various error reports (see
Troubleshooting table). In such case:
• Switch off the appliance, wait for 1 minute, switch the appliance back on, and repeat the washing program.
• If the error persists, call an authorized service unit.
• You will be able to solve most of the problems in appliance operation by yourself (see Troubleshooting
table below).
• Repairs may only be carried out by an adequately trained person.
• Repair or any warranty claim resulting from incorrect connection or use of the washing machine shall not be
covered by the warranty. In such cases, the costs of repair shall be charged to the user.
The warranty does not cover the errors or failures resulting from disturbances from the environment
(lightning strike, power grid failures, natural disasters etc.).
Problem/error
Cause
Washing machine
• Water level too high.
door does not open.
The machine will
not start.
Display does not
light up.
40
• Drain the water using the Drain or Spinning
program. See "Step 5: Choose the program".
• Water temperature in the
washing machine is too high.
• Wait for the water temperature to drop and pump
out the water. If you still cannot open the door, use
the emergency door opening tool (see chapter
"ERRORS – WHAT TO DO? / Manual opening of
washing machine door").
• Power supply failure.
• Press the Start
Washing program is • Washing machine door is not
not in progress.
properly closed.
Washing time
is longer than
anticipated (the
time is regularly
updated on the
display unit).
What to do?
button to resume the program.
• Firmly press on the washing machine door until
you hear two clicks when it is closed.
• There is no voltage in the
power outlet.
• Check if the plug is connected to the power outlet
and whether there is electric current (or voltage) in
the outlet.
• Delayed start function has
been selected.
• To cancel the delayed start function, press the
Start button and hold it for three seconds.
• Low inlet water temperature.
• Program duration can be up to 60% longer than
initially anticipated in the normal progress.
• UKS* (*unbalance system)
• Program time is extended due to the need to
stability system engaged due
redistribute the laundry in the drum.
to unevenly distributed laundry.
• Low mains voltage.
• Washing machine needs more time because the
power mains voltage is too low.
• Power supply failure.
• Program time is extended by the duration of the
power supply failure.
• There is no voltage in the
appliance.
• Check if the plug is connected to the power outlet
and whether there is electric current (or voltage) in
the outlet.
The wording on the • You have not selected your
display unit is not
preferred language yet.
in your language.
• Choose the preferred language (see "STEP 5 /
System Settings / Choosing the language").
Wet laundry
("unbalance" will
appear on display)
• Loosen and redistribute the laundry and select the
Drain or Spinning program.
• Increase the amount of laundry in the washing
machine and restart the program (see "STEP 7:
Start the wash / Adding or removing laundry after
the start of the program").
• A small amount of laundry will
often be unevenly distributed.
Problem/error
Cause
There are traces
• The laundry was very greasy.
of grease (or
grease rolls) on the
clothes.
There are still
stains on the
laundry.
What to do?
• Wash the laundry again. When your laundry is
this heavily soiled, add more washing powder or
use a liquid detergent in combination with a more
powerful (longer) program.
• You used bleach-free liquid
• Use a detergent that contains bleach.
detergent or powder detergent
for coloured laundry.
• You selected an unsuitable
program.
• Use special stain removers.
There are white
• This is not due to poor rinsing • Immediately rinse the laundry again.
residues of
by your washing machine,
• Use liquid detergents that do not contain zeolites.
washing powder on but rather due to phosphate• Try removing any residues with a brush.
the laundry.
free detergents which contain
ingredients (zeolites) for water
softening. These ingredients
may be deposited on the
laundry.
There is powder
detergent left in
the main wash
compartment
of the detergent
dispenser tray.
• Water pressure not high
enough.
• Clean the net on the water supply hose.
• Some washing powders may
stick strongly to the dispenser
tray if it is empty.
• Choose higher water level or extra rinse (see
"Step 6 / Choose program settings").
• Wipe the dispenser tray before adding the powder
detergent.
There is
• Plug cap is not positioned
conditioner left in
correctly or it is
the conditioner
clogged.
compartment of the
dispenser tray.
• Make sure the plug cap in the conditioner
compartment of the dispenser tray is positioned
correctly.
• Clean the plug cap (see chapter "CLEANING AND
MAINTENANCE / Cleaning the dispenser tray").
Odour in the
washing machine
drum.
• Residues of fabric, washing
detergent, and conditioner in
the filter.
• Check if the filter is clean.
• Development of germs and
bacteria.
• Choose a self-cleaning (Drum Cleaning) program
(see "STEP 5: Choose the program").
• Feet not adjusted correctly.
• Level the feet (see chapter "INSTALLATION AND
CONNECTION / Adjusting the feet").
• Transport bolts not removed.
• Remove the transport bolts (see chapter
"BEFORE USING THE APPLIANCE FOR THE
FIRST TIME / Transport protection").
• Unevenly distributed laundry
or not enough laundry.
• The washing machine will automatically decrease
the spin speed if vibration is too strong.
• Increase the amount of laundry in the washing
machine and restart the program (see "STEP 7:
Start the wash / Adding or removing laundry after
the start of the program").
Machine is moving
during operation.
Machine is moving
during spinning.
41
Manual opening of washing machine door
Washing machine door may be opened manually if the appliance is not connected to the power mains
and if the water has been pumped out of the machine.
A Choose the Spinning or Drain program to pump the water from the machine. If this does not work, water has
to be drained from the washing machine drum manually. See chapter "Cleaning the trap and drain pump" in
the chapter "CLEANING AND MAINTENANCE".
B Make sure the main switch is off and that the plug is disconnected from the power outlet.
C Take the emergency door opening tool (found at the back of the dispenser) and insert it into the upper part
of the slot on the right-hand side of the washing machine door latch.
D Press the key (key=the emergency door opening tool) downwards (all the way, until you hear a click) to
unlock the washing machine door. When the door is unlocked, open it by pulling towards you.
1
2
If the washing machine door still cannot be opened, call a service technician.
42
FAILURE DISPLAY
In case of a failure while a program is in progress, the relevant Error XX is indicated on the display unit.
Press the INFO button to display the
Error Message
error description.
Error XX
Info
Exit
Switch off the appliance and turn it back
on.
5
Errors indicated on the display unit may include the following:
Error
Error indication on the display unit
What to do?
E1
THERMISTOR ERROR
Temperature sensor error.
• Inlet water too cold. Repeat the washing program.
• If the appliance reports this error again, call a service
technician.
E2
DOOR LOCK ERROR
Restart the program. If the error reoccurs, call a
service technician.
E3
WATER FILLING ERROR
Check the following:
• is the water inlet valve open,
• is the filter on the water inlet hose clean,
• is the water supply hose deformed (clipped, clogged
etc.).
Then, press the Start button to resume the
program.
If the error reoccurs, call a service technician.
E6
HEATING ERROR
Water heating error.
Restart the program. If the error reoccurs, call a
service technician.
E7
DRAINING ERROR
Water draining error.
Check the following:
• is the pump filter clean,
• is the drain hose clogged,
• is the drain clogged,
• is the drain hose fitted at the right height (see chapter
on drain hose installation in the instruction manual).
Then, press the Start button again. If the error
reoccurs, call a service technician.
DRAIN SYSTEM ALERT
Water drain system alert.
Alert about reduced water flow in the pumping stage.
Check the following:
• is the pump filter clean,
• is the drain hose clogged,
• is the drain clogged,
• is the drain hose fitted at the right height (see chapter
on drain hose installation).
E8
SPINNING ERROR
Restart the programme. If the error reoccurs, call a
service technician.
E10
WATER LEVEL SENSOR ERROR
Restart the program. If the error reoccurs, call a
service technician.
E7.1
43
Error
Error indication on the display unit
What to do?
E11
OVERFLOW
If there is water in the drum, the washing machine
will automatically stop adding water. Use the Drain
programme. Restart the programme. If the error
reoccurs, call a service technician.
If there is water in the drum and the washing machine
continues to add water, close the water tap and call a
service technician.
E12
MOTOR ERROR
Restart the program. If the error reoccurs, call a
service technician.
E13.1
UNBALANCE EMPTY DRUM
Call a service technician.
E13.2
INERTIA ERROR
Call a service technician.
E22
DOOR LOCK ERROR
Error while locking the door.
Door is closed, but it cannot be locked. Close the door
again. Turn the washing machine off, then restart the
washing program. If the error reoccurs, call a service
technician.
E23
DOOR UNLOCK ERROR
Error while unlocking the door.
Door is closed, but it cannot be unlocked. Turn off
the washing machine, then turn it back on. If the error
reoccurs, call a service technician. See instructions for
opening the door – chapter on manual door opening.
E29
REED SWITCH 1 ERROR
Call a service technician.
E30
REED SWITCH 2 ERROR
Call a service technician.
E31
PERISTALTIC PUMP 1 ERROR
Call a service technician.
E32
PERISTALTIC PUMP 2 ERROR
Call a service technician.
E33
AD1 DETERGENT LEVEL SENSOR ERROR Restart the programme. If the error reoccurs, call a
service technician.
E34
AD2 DETERGENT LEVEL SENSOR
ERROR.
Restart the programme. If the error reoccurs, call a
service technician.
E35
COMMUNICATION AD AND PMCU
Turn off the appliance and turn it back on. If the error
reoccurs, call a service technician.
E36
COMMUNICATION UI AND PMCU
Error in UI and PMCU communication.
Turn off the appliance and turn it back on. If the error
reoccurs, call a service technician.
UNBALANCE
Unevenly distributed laundry.
Manually distribute the laundry and run the spinning
program.
STERIL TUB ALERT
Warning – Self-cleaning program
Use the self-cleaning program (DRUM CLEANING);
see STEP 5.
** UI = (User Interface)
Unevenly distributed laundry or lumps of laundry in the washing machine drum may cause problems such
as vibration and noisy operation. The washing machine will sense this and activate the UKS* (*unbalance
system).
Smaller loads (e.g. one towel, one sweater, one bathrobe etc.) or clothes made of materials with special
geometrical properties are virtually impossible to distribute evenly across the washing machine drum
(slippers, large items etc.). This results in several attempts to redistribute the laundry, which in turn leads to
longer program duration. In extreme cases of unfavourable conditions, the program can be completed without
the spinning cycle.
UKS* (*unbalance system) allows stable operation and extends the useful life of the appliance.
44
SERVICE
BEFORE CALLING A SERVICE TECHNICIAN
1, 2, 3
When you contact a service centre, please state
the model (1), type (2), and serial number (3) of your
washing machine.
Model, type, and serial number are indicated on the
rating (type) plate located on the washing machine
door casing.
In case of a failure, only use approved spare
parts by authorized manufacturers.
Repair or any warranty claim resulting from
incorrect connection or use of the washing machine
shall not be covered by the warranty. In such cases,
the costs of repair shall be charged to the user.
2
3
1
TYPE: WMXX.XXXXX MODEL: XXXXXX.X
Art.No.: XXXXXX/XX
Ser.No.: XXXXXXXX
XXX-XXX V ~ XXXX W
IPX4
XX Hz
XXA
X kg
XX-X MPa
45
TECHNICAL INFORMATION
INFORMATION ON ENERGY LABELLING
Information sheet pursuant to the Commission Regulations (EU) No. 1061/2010 and 1015/2010
Model
WM75.2
Maximum washing load
9 kg
Energy efficiency class
A+++
Annual energy consumption (AEC)
185 kWh na year1)
Power consumption
Standard cotton + ECO 60 °C with a full load (Et,60)
0,93 kWh
Standard cotton + ECO 60 °C with half load (Et,60½)
0,88 kWh
Standard cotton + ECO 40 °C with half load (Et,40½)
0,60 kWh
Power consumption
Off (P0)
0,3 W
Mode without switching off (Pl)
0,7 W
Annual water consumption (AWC)
10590 litres per year2)
Spinning efficiency class
A3)
Maximum spin speed
1800 rpm
Residual moisture
43 %
Washing program
Standard cotton + ECO4)
60 °C
40 °C
Program duration
Standard cotton + ECO 60 °C with a full load (Et,60)
183 minutes
Standard cotton + ECO 60 °C with half load (Et,60½)
175 minutes
Standard cotton + ECO 40 °C with half load (Et,40½)
155 minutes
Noise emissions
Washing stage
50 dB(A) re 1 pW
Spinning stage
78 dB(A) re 1 pW
1)
Based on 220 standard washing cycles for Standard cotton + ECO 60 °C and 40 °C for full and half load in energy saving modes. Actual power consumption
will depend on the way the appliance is used.
Based on 220 standard washing cycles for Standard cotton + ECO 60 °C and 40 °C with full and half load. Actual water consumption will depend on the way
the appliance is used.
3)
On a scale from G (the least efficient) to A (the most efficient).
4)
Standard cotton + ECO, 60 °C and 40 °C are standard washing programs used for gathering the information for the energy label. These programs are intended
for washing normally soiled cotton fabric and they are the most efficient in terms of overall power and water consumption. Actual water temperature may
deviate from the temperature selected for the washing cycle.
2)
ECO=Green Mode
46
PERFORMANCE DATA
Program
Maximum load
Temp. °C
Standard cotton + ECO 1)
9 /4,5* kg
60 °C
Everyday wash 2)
9 /4,5* kg
60
Mix/Synthetics2)
3,5 kg
40
40 °C
1)
Test program for connection to cold water supply, pursuant to EN 60456.
40 °C program for testing institutes. The 40 °C option has to be set.
* Half load
⌑
ECO=Green Mode
2)
ENERGY LABELLING
European test standard
EN 60456
Washing program
Standard cotton + ECO
Connection
Cold water 15 °C
Noise testing method
IEC-60704-2-4
60 °C
40 °C
, 9 kg cotton
TECHNICAL INFORMATION
Height
850 mm
Width
595 mm
Depth
580 mm
Weight
88,5 kg
Drum volume
60 l
Rated power
See rating plate
Heater power
See rating plate
Water pressure
0,1–1 MPa
1–10 kp/cm2
10–100 N/cm2
Material for the drum and dispenser
Stainless steel
Housing material
Hot-dip galvanized and powder coated sheet metal, or
stainless steel sheet (depending on model)
Water connection
1.5 m pex hose
Drain hose
1.6 m polypropylene hose
47
Spinning speed
(rpm)
Maximum load
(kg)
Water consumption
(approximately, in litres)
Power consumption
(approximately, kWh)
Program duration
(approximately, in hours
and minutes)
1. Everyday wash
X
I
1800
9
73
2,10
2:20
2. Standard cotton
X
X
9
73
1,80
2:20
N
1800
60
1)
N
1800
43
9/4,5*
55
0,93/0,88*
3:03/2:55*
40
1)
N
1800
43
9/4,5*
55
0,67/0,60*
2:45/2:35*
X 40
2)
S
1000
3,5
50
0,35
1:52
H
800
2
58
0,28
0:55
E
1000
3
40
0,53
1:20
30
E
1000
2
-
-
-
40
N
1200
9
-
-
-
X
N
1200
3
40
0,50
0:50
X
I
1800
9
100
2,50
3:50
10. Rinse
N
1800
3,5
30
0,06
0:28
11. Spin
-
1800
9
-
0,06
0:17
12. Drain
-
9
-
0,01
0:01
3,5
50
0,45
1:50
-
-
-
Standard cotton
60 °C
40 °C
⌑
+ECO
3. Mix/Synthetics
40
Residual moisture [%]
Agitation level**
Program
Temp. °C
X 602)
Prewash
Super rinse
PROGRAM TABLE
4. Wool/Hand wash
30
5. Dark wash
40
6. Time program
X
7. Auto program
8. Quick program
9. Heavy
X
13. Easy care
60
40
X
X
X
14. Drum cleaning
E
1000
N
15. Jeans
X
40
X
S
1000
3,5
50
0,60
1:20
16. Shirts
X
40
X
E
1000
3,5
45
0,45
1:05
60
I
1800
9
87
1,80
2:40
40
S
1000
3,5
43
0,40
0:55
X
S
1000
3,5
15
0,03
0:23
17. Hygiene
18. Sports wear
X
19. Conditioning
20. Stain program
40
X
I
1800
9
-
-
-
21. Bedding
60
X
N
1800
4
52
1,67
2:05
22. Allergy program cotton
60
I
1800
9
95
1,85
2:50
23. Allergy program synthetics
60
S
1000
4
70
1,10
2:20
24. Quick Pro
40
N
1000
4
40
0,50
0:59
⌑
ECO=Green Mode
Cold wash
* Half load
**Agitation level (I = Intensive rhythm, N = Normal rhythm, E = Extra sensitive rhythm, S = Sensitive rhythm, H = Hand wash rhythm)
1)
Test program for connection to cold water supply, pursuant to EN 60456.
2)
40 °C program for testing institutes. The 40 °C option has to be set.
The above table includes several examples of the use of energy, water, and time for several different program settings. Actual consumption or duration
may vary depending on the water pressure, water hardness, water inlet temperature, room temperature, weight and type of load, changes in power
supply, and selected options or settings. In the examples specified here, the draining is set to Normal and no additional options are selected.
Maximum or nominal load applies to laundry prepared pursuant to the IEC 60456 standard.
48
Adjustment of the displayed washing time
Advanced technology allows the appliance to sense the amount of laundry and add the required amount of
water during the washing process. Depending on the washing load, washing time can be longer or shorter
and the time displayed will be adjusted accordingly.
Moreover, displayed washing time may change due to differences in inlet water temperature. At low inlet
water temperatures, washing time can be longer; at higher temperatures, it can be shorter.
Unevenly distributed laundry or lumps of laundry in the washing machine drum can cause problems such as
vibration and noisy operation. The appliance can sense such lumps and will try to redistribute the laundry.
Smaller loads (e.g. one towel, one sweater, one bathrobe etc.) or clothes made of materials with special
geometrical properties are virtually impossible to distribute evenly across the washing machine drum
(slippers, large items etc.). This results in several attempts to redistribute the laundry, which in turn leads to
longer program duration.
49
TABLE: WASHING MODE/TEMPERATURE
1. Everyday wash
- 90°C
20°C - 90°C
- 90°C
2. Standard cotton
- 90°C
20°C - 90°C
- 90°C
3. Mix/Synthetics
- 60°C
20°C - 60°C
- 60°C
4. Wool/Hand wash
,
30°C - 40°C
,
30°C - 40°C
5. Dark wash
,
30°C - 40°C
,
30°C - 40°C
6. Time program
- 60°C
7. Auto program
- 90°C
8. Quick program
9. Heavy
30°C - 90°C
30°C - 60°C
30°C - 40°C
Intense
Night
Allergy
Speed
Green
Program
Normal
Washing mode
- 90°C
40°C-90°C
- 90°C
40°C-90°C
- 60°C
40°C-60°C
,
30°C - 40°C
40°C
, 40°, 60°,
90°C
- 90°C
30°C - 90°C
- 90°C
30°C-60°C
- 60°C
10. Rinse
11. Spin
12. Drain
13. Easy care
- 60°C
20°C - 60°C
- 60°C
40°C-60°C
14. Drum cleaning
15. Jeans
,
30°C - 40°C
,
30°C - 40°C
16. Shirts
,
30°C - 40°C
,
30°C - 40°C
17. Hygiene
60°C - 90°C
18. Sportswear
30°C - 40°C
30°C-40°C
,
30°C - 40°C
40°C
,
30°C - 40°C
60°C-90°C
19. Conditioning
20. Stain program
21. Bedding
40°C - 90°C
22. Allergy program cotton
60°C - 90°C
23. Allergy program synthetics
60°C
24. Quick Pro
40°C
Cold wash
50
30°, 40°,
60°, 90°C
40°C - 90°C
40°C - 90°C
40°C - 90°C
TABLE OPTIONS
1. Everyday wash
1800
2. Standard cotton
1800
3. Mix/Synthetics
1000
4. Wool/Hand wash
800
5. Dark wash
1000
6. Time program
1000
7. Auto program
1200
8. Quick program
1200
9. Heavy
1800
10. Rinse
1800
11. Spin
1800
12. Drain
0
13. Easy care
14. Drum cleaning
Start delay
Anti-crease
High water level
Prewash
Super Rinse
Program
Spinning speed
(rpm)
Options
1000
/
15. Jeans
1000
16. Shirts
1000
17. Hygiene
1800
18. Sportswear
1000
19. Conditioning
1000
20. Stain program
1800
21. Bedding
1800
22. Allergy program cotton
1800
23. Allergy program synthetics
1000
24. Quick Pro
1000
Option (setting) available on Program
51
DISPOSAL
Disposal / recycling of packaging
Our product packaging is made of environmentally friendly materials that can be recycled, disposed
of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled
appropriately.
The symbol on the product or its packaging indicates that the product should not be treated as
normal household waste. The product should be taken to an authorized collection centre for waste electric and
electronic equipment processing.
When disposing of an appliance at the end of its useful life, remove all power cords and destroy the door latch
and switch to prevent the door from locking or latching (child safety).
Correct disposal of the product will help prevent any negative effects on the environment and health of people
which could occur in case of incorrect product removal. For detailed information on removal and processing of
the product, please contact the relevant authority in charge of waste management, your waste disposal
service, or the store where you bought the product.
52
NOTES
53
NOTES
54
QUICK GUIDE
SORT THE LAUNDRY.
1.
Close the zippers.
Empty the pockets and turn them inside out.
Check the laundry care symbols.
Sort the laundry based on how heavily soiled it is, by colour, and by
material.
SWITCH ON THE MAIN ON/OFF SWITCH (ON/OFF)
2.
3.
OPEN THE WASHING MACHINE DOOR AND INSERT
THE LAUNDRY.
Before doing so, make sure the drum is empty.
ADD THE DETERGENT AND THE CONDITIONER.
4.
Recommended detergent amount is usually indicated on the
packaging.
For smaller wash loads, use a smaller amount of detergent.
See chapter "SPECIAL FEATURES" for ADS settings.
CHOOSE THE WASHING PROGRAM.
5.
Turn the program selector knob to the desired washing program.
Selected program will be indicated on the display unit.
CHOOSE THE PROGRAM SETTING.
Choose the settings by pressing the relevant buttons.
6.
7.
CLOSE THE WASHING MACHINE DOOR AND PRESS
THE ”START” BUTTON.
Anticipated washing time, in hours and minutes, will be indicated on
the display.
END OF PROGRAM
8.
Open the door and remove the laundry from the washing machine.
See chapter "CLEANING AND MAINTENANCE".
Close the door.
Switch off the main on/off switch.
Close the water tap and remove the power plug from the power socket.
We reserve the right to modifications.
55
Gorenje, Partizanska 12, 3320 Velenje, Slovenija
www.asko.com
WM75.2
en (02-18)
Download PDF