/
/
/
/
INSTALLATION MANUAL
Applied Machines:
/
/
/
/
<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
I. Outline of installation procedures (C554e/C454e)
✱ Electronic system options
KP-101
EK-606*1
HT-509
TK-101
UK-204*1
MK-734
PC-110
PC-210
PC-410
SC-508*1
DK-510
AU-201
DK-705
UK-208*1
MK-730
SP-501
AU-102
Machine
WT-506
EK-607*1
VI-506
LU-204
IC-414
LU-301
FK-511
Electronic system options
FK-508*3
MK-735
MK-728*3
*1:
No particular order in installation procedures.
Unable to be installed in C454e.
*3: Varies depending on the applicable marketing area
*2:
KH-102
PK-519
FS-533
FS-534
FS-534SD
OT-506
PK-521*2
SD-511
PK-520
SD-512*2
ZU-606*2
*2
FS-535
JS-506
JS-602*2
PI-505*2
When installing the machine and associated options as a system, follow the order shown on the upper.
Caution:
could result in personal injury. When transport• For the detailed installation procedures for each
ing the machine, assign an adequate number of
option, follow the instructions given in the correpersons to the job and ensure that each person
sponding installation manual and perform the
can take a good position of not being excesprocedures correctly. (Optional devices must be
sively loaded.
installed after completing the main unit installation.)
(mass: approx. 101 kg (222-11/16 lb))
• Once the Power Switch is turned ON, do not
turn OFF it until the installation work has been
completed.
• When placing the machine on the floor, make
sure to use the paper feed cabinet or the desk
to secure the performance and the quality of
the product.
• Lifting the machine in an awkward position or
transporting it in a poorly balanced position
A2XKIXC001DA
E-1
A5C1-9620-12
Outline of installation procedures (C364e/C284e/C224e)
✱ Electronic system options
KP-101
EK-606*1
HT-509
UK-204*1
MK-734
PC-110
PC-210
PC-410
EK-607*1
DK-510
DK-705
UK-208*1
UK-209
SC-508
AU-102
AU-201
DF-701
WT-506
Machine
MK-730
VI-506*2
Electronic system options
IC-414*2
MK-735
FK-511
SP-501
DF-624
FK-508*3
OC-511
*1:
PK-519
FS-533
JS-506
FS-534
PK-520
SD-511
FS-534SD
*2:
*3:
MK-728*3
No particular order in
installation procedures.
Unable to be installed in
C224e.
Varies depending on the
applicable marketing area
KH-102
When installing the machine and associated options as a system, follow the order shown on the upper.
Caution:
• Lifting the machine in an awkward position or
• For the detailed installation procedures for each
transporting it in a poorly balanced position
option, follow the instructions given in the correcould result in personal injury. When transportsponding installation manual and perform the
ing the machine, assign an adequate number of
procedures correctly. (Optional devices must be
persons to the job and ensure that each person
installed after completing the main unit installacan take a good position of not being excestion.)
sively loaded.
• When placing the machine on the floor, make
(mass: approx. 85 kg (187-3/8 lb))
sure to use the paper feed cabinet or the desk
to secure the performance and the quality of
the product.
• To use this machine, install the dual scan document feeder, the reverse automatic document
feeder, or the original cover.
Even if you do not install the original cover, be
sure to install the hinge covers supplied with
the original cover.
• Once the Power Switch is turned ON, do not
A161IXC001DA
turn OFF it until the installation work has been
completed.
E-2
II. Installation space (unit: mm (inch))
III. Pre-installation check items
bizhub C554e + PC-210 + ZU-606 + FS-535
+ LU-204
1. Select a level and stable place for installing the
machine.
2. Be sure to use a power source of the voltage and
frequency indicated in the product specifications.
Ensure that the current carrying capacity of the
power outlet is at least equal to the current listed
in the product specifications.
3. Power the machine directly from a dedicated
power outlet. (Do not use an extension cord.)
4. Do not plug or unplug the power cord with wet or
dirty hands, otherwise you may get an electric
shock.
5. Avoid a hot and humid environment, or a place
exposed to direct sunlight.
6. Avoid a dusty location, or a place near volatile
and flammable substances.
7. Avoid a poorly ventilated place.
2763
(108-3/4)
1217
(47-15/16)
1066
(41-15/16)
480
(18-7/8)
1246
(49-1/16)
428
(16-7/8)
818
(32-3/16)
936
(36-7/8)
Be sure to instruct users on the following points.
• This machine uses a capacitive touch panel.
When you touch the touch panel, use your finger or the stylus pen supplied with the machine.
If you touch the panel using your nail or a pen
tip instead of using your finger or the stylus pen,
the touch panel does not respond normally.
• Pressing the touch panel hard may cause damage.
• Do not strongly press the panel or press it using
the sharp tip of mechanical pencils.
• The key is a finger tapping (quick light touch
using a finger) operation.
246
(9-11/16)
1568
(61-3/4)
386
(15-3/16)
IV. Notes on using touch panel
A61DIXC021DB
bizhub C364e + DF-701 + PC-210 + FS-534
+ MK-730
660
(26)
1822
(71-3/4)
937
(36-7/8)
225
(8-7/8)
1246
(49-1/16)
818
(32-3/16)
936
(36-7/8)
246
(9-11/16)
1568
(61-3/4)
386
(15-3/16)
428
(16-7/8)
A61DIXC022DB
E-3
V. Accessory parts
No.
Name
Note:
The parts shown below are used when installing
options. Keep them safe.
• Paper size label: Large capacity unit (LU-301)
(C554e/C454e only)
• Label (Super G3 label): Fax kit
Q’ty
1. User’s guide holder
1
2. Quick start guide
1
3. Installation manual
1 set
4. User’s guide CD
1
5. CD-ROM
1 set
6. Paper size label
1
7. Label (Legal restrictions on copying) *1
1
8. Label (Super G3 label)
1
9. Panel sheet
1
10. Cap A (Black)
2
11. Cap B (White)
2
12. Power cord *1
1
13. Power cord instruction *1
1
14. Cord clamp*2
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
Note:
This manual provides the illustrations of the accessory parts and machine that may be slightly different in shape from yours. In that case, instead of
the illustrations, use the appearance of your
machine to follow the installation procedure. This
does not cause any significant change or problem
with the procedure.
0 to 2
15. Connector cover
1
16. Duct cover
1
17. Screw A *1*3
1
A1530308
18. Screw B
1
V1160308
19. Screw C *1
1
V1160330
20. Chart *4
1
21. Stylus pen
1
22. Waste toner box
1
*1
Varies depending on the applicable marketing
area.
*2
North American market: N/A
C554e/C454e for markets other than North America: One
C364e/C284e/C224e for markets other than
North America: Two
*3 C364e/C284e/C224e only
*4 C554e/C454e only
E-4
VI. Removing the machine
VII. Removing protective tape, packing
and other shipping materials
1. Unpack and remove the machine package.
2. Remove the machine, holding it by the locations
on the left side and the handles on the right side
as shown in the illustration and keeping it level.
Caution:
Machine mass
C554e/C454e: approx. 101 kg/222-11/16 lb
C364e/C284e/C224e: approx. 85 kg/187-3/8 lb
• Make available collective manpower of an
appropriate size for transporting the machine.
• Before attaching the machine to the paper feed
cabinet, make sure that the supplied connector
cover is not attached.
• When attaching the machine, as the reference
fit the machine with the corner A and B of the
paper feed cabinet.
1. Remove the protective tape and the protective
materials.
Note:
After removing protective tape A, be sure to push
the area indicated by the “
” mark to lock the
guide. (C554e/C454e only)
<C554e/C454e>
When holding the transportation handles,
be careful not to catch your fingers in the
machine.
A5AYIXC002DC
A2XKIXC003DA
A
Connector cover
A
B
A5AYIXC003DC
A2XKIXE034DA
E-5
2. Open the right door and remove the protective
sheet and packaging materials.
Note:
After removing the packaging materials, make
sure that the transfer roller assy is secured in
place. In the case of <NG>, press the transfer
roller assy into place so that it is secured as shown
in <OK>.
<C364e/C284e/C224e>
B
<Viewed from point B>
A5C1IXC001DB
< OK >
< NG >
A5C1IXC002DA
A161IXC005DB
3. Remove the locking screws.
A5C1IXC003DB
A2XKIXC008DA
4. Remove the protective sheets.
A5C1IXC004DA
A2XKIXC009DA
E-6
9. <C554e/C454e>
Open the lower front door.
5. Slide out the tray 1.
6. Remove the protective tapes from the inside of
the tray 1 and remove accessory part.
A2XKIXC010DA
A5C1IXC032DA
<C364e/C284e/C224e>
Open the front door.
7. Slide out the tray 2 and remove the tray locking
materials.
A161IXC015DB
A5C1IXC014DA
10. Remove the protective tape.
8. Remove the protective tapes from the inside of
the tray 2 and remove accessory parts.
<C554e/C454e>
Protective tape
A2XKIXC011DA
<C364e/C284e/C224e>
A5C1IXC015DA
Protective tape
A5C1IXC016DA
E-7
14. Slightly slide the drum unit (K) out and remove
the protective tape
11. Remove the protective tape from the developing
units.
Note:
Do not remove the tape A in this procedure.
A
A2XKIXC015DA
15. Slide the drum unit (K) into the machine.
16. Lock the drum unit (K) with the lever.
17. Install the supplied waste toner box.
Note:
Push the areas indicated by the “ ” marks to set
the waste toner box to the machine
A5AYIXC005DB
12. Remove the protective materials from the four
places.
Note:
Keep the protective materials. It is necessary for
transporting the machine.
A2XKIXC013DA
13. Release the lever of the drum unit (K).
A2XKIXC016DA
* Perform the following steps 18 and 19 only when
installing C554e/C454e.
18. Close the lower front door.
19. Open the upper front door.
A2XKIXC014DA
E-8
VIII. Installing the toner cartridge
3. Push the toner cartridge all the way in and rotate
it clockwise to lock it.
Note:
Make sure that the toner cartridge is pushed all the
way in.
Note:
Since cartridge is not supplied with the machine,
purchase toner cartridge (of different colors) separately.
1. Shake the toner cartridge up and down and left to
right 5 to 10 times respectively.
Note:
Shake the cartridge adequately. Otherwise, it may
cause trouble.
A2XKIXC018DA
4. Using the same procedure, install the toner cartridges for other colors of toner.
5. <C554e/C454e>
Close the upper front door.
<C364e/C284e/C224e>
Close the front door.
A0EDIXC020DA
2. Insert the toner cartridge into the machine.
Note:
• Make sure that the color is same between
inserting port and the toner cartridge.
• Make sure that the blue label position of the
toner cartridge is matched with the one of the
machine side.
IX. Mounting the accessory parts
1. Attach the supplied caps A and B.
A2XKIXC019DA
2. Remove the protective cover from the supplied
stylus pen.
Note:
Discard the removed protective cover.
A2XKIXC017DA
A2X0IXC068DA
E-9
3. Set the stylus pen in the place shown in the illustration.
6. Attach the supplied duct cover.
A5C1IXC007DA
4. Attach the supplied cord clamp to the scanner
rear cover of the machine. (One supplied screw
A)
Note:
• Only C364e/C284e/C224e needs this step.
• This may not be performed depending on the
applicable marketing area.
A5C1IXC021DA
X. Connecting the power cord
Note:
Steps 1 and 2 may be unnecessary depending on
the applicable marketing area.
1. Connect the power cord.
A161IXE047DA
5. Attach the supplied connector cover to the
machine. (One supplied screw B)
A161IXE042DA
2. Fit the supplied cord clamp over the power cord.
(One supplied screw C)
A161IXE065DA
A161IXE043DB
E-10
3. Plug the power cord into the power outlet.
XIII. Serial number input
Note:
Serial number input is needed only for optional
devices that will be installed later.
1. Select the Serial Number Input function as follows: System 1 → Serial Number.
2. Touch the item you want to enter and input the
serial number.
3. Touch “END.”
4. For other devices, enter their serial number in the
same way.
5. Touch “END.”
C4004U139CA
XI. Toner supply
Turn ON the Main Power Switch.
Note:
• Toner is automatically supplied in parallel with
warm-up.
• If any one of the toner cartridges is not set,
toner supply does not start.
XII. Date & Time Setting/Time Zone Setting
(Service Mode)
1. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
2. Display the Date & Time Setting/Time Zone Setting screen.
(To display the Date & Time Setting/Time Zone
Setting screen, press Stop → 1 → 1 → 4 → 4 →
Clear on the control panel.)
3. Input the time zone using up/down keys or direct
keys.
4. Touch “Entry.”
5. Touch “Apply.”
6. Touch “OK.”
7. Touch “END.”
XIV. Unit change
Note:
This function allows the user to select the type of
message that will appear when the replacement
time arrives for each of the different units.
1. Select the Unit Change function as follows:
System 2 → Unit Change.
2. Select the appropriate message type for each
unit.
3. Touch “END.”
XV. List output
1. Load the tray 1 with A4
or Letter
paper.
2. Touch “List Output.”
3. Check that “Machine Management List” is
selected and press the start key.
The list will be output.
4. Output “Adjustments List” in the same way.
5. Touch “2.”
6. Check that “Service Parameter” is selected and
press the start key.
The list will be output.
7. Touch “END.”
8. Touch “Exit” on the Service Mode screen.
9. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
Mode screen and wait for 10 seconds or more
before turning on.
E-11
XVI. Adjusting the height
Note:
• The following “XVI. Adjusting the height” to
“XXI. Adjusting the document stop position” and
“XXIII. Changing the stopper position” shall be
referenced only when installing C554e/C454e.
• When installing the dual scan document feeder
DF-701 or reverse automatic document feeder
DF-624 to C364e/C284e/C224e, adjustments
shall be made according to the installation manual of each option.
2. If there is any clearance, adjust the height by
turning the adjustment screw on the right side
viewed from the back.
Clockwise: The rear side will move up.
Counterclockwise: The rear side will move down.
• If further adjustment is required, adjust the height
by using the adjustment screw on the left side
viewed from the back together.
Clockwise: The rear side will move up.
Counterclockwise: The rear side will move down.
1. Check the clearance between the upper face of
scanner and the protrusion on the dual scan document feeder side. (Three spots)
* There must be no clearance between the protrusion on the dual scan document feeder and the
upper face of scanner.
A2XKIXE027DB
XVII. Adjusting skew feed (Front side)
Note:
Perform this adjustment if necessary.
OK
Protrusion
1. Close the dual scan document feeder.
2. Check how the edges of the chart are misaligned.
The amount of the deviation of the chart will be X.
NG
A3CFIXC010DA
X
Protrusion
Deviation in + (plus)
X
Deviation in - (minus)
9J07IXC043DA
Protrusion
A3CEIXC003DB
E-12
3. Place the chart in the document feeding tray (with
the side having an arrow facing up).
8. When the difference of the deviation is + (plus),
turn the adjustment screw located at the back of
the dual scan document feeder clockwise to
adjust.
Note:
• Look at the guide lines when making the adjustment.
• When turning the screw, be sure not to raise the
dual scan document feeder until in an upright
position.
* To prevent the adjustment screw breakage, be
sure to follow the above instructions.
A3CFIXC013DA
Guide lines
4. Make copies 5 times repeatedly in single side
mode.
5. Fold all 5 sample copies as illustrated and check
for any deviation.
Deviation on the sample will be Y.
Y
Y
A2XKIXC026DC
Deviation in + (plus)
Deviation in - (minus)
9J07IXC043DA
6. Obtain the difference between the deviation of
the chart and the deviation of the sample.
Difference of the deviation = Y - X
Specifications: 0 ± 2 mm
* If the difference of the deviation does not fall
within the specified range, perform the following
adjustment.
7. Loosen the mounting screw on the right hinge
viewed from the front.
Mounting screw
A3CEIXC004DA
E-13
9. When the difference of the deviation is - (minus),
turn the adjustment screw located at the back of
the dual scan document feeder counterclockwise
to adjust.
Note:
• Look at the guide lines when making the adjustment.
• When turning the screw, be sure not to raise the
dual scan document feeder until in an upright
position.
* To prevent the adjustment screw breakage, be
sure to follow the above instructions.
3. Fold all 5 sample copies as illustrated and check
for any deviation.
Deviation on the sample will be Z.
Z
Deviation in + (plus)
Z
Deviation in - (minus)
Guide lines
9J07IXC043DA
4. Obtain the difference between the deviation of
the chart and the deviation of the sample.
Difference of the deviation = Z - X
Specifications: 0 ± 2 mm
* If the difference of the deviation does not fall
within the specified range, perform the following
adjustment.
5. Open the dual scan document feeder and remove
the two screws shown in the illustration.
A2XKIXC025DC
10. Tighten the mounting screw on the right hinge
that has been loosened in step 7 using a screwdriver.
XVIII. Adjusting leading edge skew
(Back side)
Note:
Perform this adjustment if necessary.
A3CEIXC032DA
1. Place the chart in the document feeding tray
(Make sure that the blank surface of the chart
faces up).
6. Close the dual scan document feeder.
7. Remove the front cover.
A3CEIXC033DA
A3CEIXC039DA
2. Make copies 5 times repeatedly in duplex mode.
E-14
8. Loosen the two screws shown in the illustration.
XIX. Magnification adjustment
<Magnification in the feeding direction>
Note:
Perform this adjustment if necessary.
1. Place the chart in the document feeding tray
(with the side having an arrow facing up).
A3CEIXC034DA
9. Turn the adjustment dial according to the difference of the deviation.
When the difference is a positive (+) value, turn
the dial clockwise
When the difference is a negative (-) value, turn
the dial counterclockwise
A3CFIXC013DA
2. Make a single-sided copy sample in full size.
3. Check whether the difference in the width C
between the chart and the copy sample is within
the specified range.
Difference in the width C = C of the copy sample
– C of the chart
Specifications: 0 ± 1.0 mm
* If the difference in the width C does not fall within
the specified range, perform the following
adjustment.
A3CEIXC035DA
10. Make duplex copies and check the amount of
deviation (Z).
11. After completing the adjustment, tighten the
screws loosened in step 8.
12. Install the front cover removed in step 7. (Two
screws)
A1DMIXC018DA
4. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
5. Touch “ADF.”
6. Touch “FD-Mag. Adj.(F).”
7. Check that “Orig. Feed Zoom Ad” is selected.
8. Specify a value using the -/+ key.
Adjustable range: -2.00 % to +2.00 %
(0.1% per step)
If the difference in the width C is greater than the
specifications, use the – (minus) key.
If the difference in the width C is smaller than the
specifications, use the + (plus) key.
9. Touch “Test Copy.”
10. Select the tray loading paper for the test copy.
11. Touch “2.”
E-15
12. Check that “1-Sided -> 1-Sided” is selected.
13. Place the chart in the document feeding tray
(with the side having an arrow facing up).
14. Press the start key, and check the difference in
the width C between the chart and the discharged copy sample.
<Back side magnification in the feeding direction>
Note:
Perform this adjustment if necessary.
15. Place the chart in the document feeding tray.
(Make sure that the blank surface of the chart
faces up.)
A3CEIXC039DA
16. Make a duplex copy sample in full size.
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “2-Sided -> 2-Sided” and then
press the start key to make a copy sample.
18. Display the Service Mode screen, and touch
“ADF.”
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “END” twice.
19. Touch “FD-Mag. Adj.(B).”
20. Check that “Orig. Feed Zoom Ad” is selected.
21. Specify a value using the -/+ key.
Adjustable range: -2.00 % to +2.00 %
(0.1% per step)
If the difference in the width C is greater than the
specifications, use the – (minus) key.
If the difference in the width C is smaller than the
specifications, use the + (plus) key.
22. Touch “Test Copy.”
23. Select the tray loading paper for the test copy.
24. Touch “2.”
25. Touch “2-Sided -> 2-Sided.”
26. Place the chart in the document feeding tray.
(Make sure that the blank surface of the chart
faces up.)
27. Press the start key, and check the difference in
the width C between the chart and the discharged copy sample.
<Back side zoom in the main scanning direction>
Note:
Perform this adjustment if necessary.
28. Place the chart in the document feeding tray.
(Make sure that the blank surface of the chart
faces up.)
17. Check whether the difference in the width C
between the chart and the copy sample is within
the specified range.
Difference in the width C = C of the copy sample
– C of the chart
Specifications: 0 ± 1.0 mm
* If the difference in the width C does not fall within
the specified range, perform the following
adjustment.
A3CEIXC039DA
29. Make a duplex copy sample in full size.
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “2-Sided -> 2-Sided” and then
press the start key to make a copy sample.
A1DMIXC018DA
E-16
30. Check whether the difference in the width D
between the chart and the copy sample is within
the specified range.
Difference in the width D = D of the copy sample
– D of the chart
Specifications: 0 ± 2.0 mm
* If the difference in the width D does not fall within
the specified range, perform the following
adjustment.
XX. Mixed original size adjustment
Note:
Perform this adjustment if necessary.
1. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
2. Touch “ADF.”
3. Touch “Mixed original size adjustment.”
4. Place the chart in the document feeding tray
(lengthwise).
A1DMIXC015DA
31. Display the Service Mode screen, and touch
“ADF.”
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “END” twice.
32. Touch “Main Scanning Direction Zoom.”
33. Check that “Main scanning direction zoom adj.”
is selected.
34. Specify a value using the -/+ key.
Adjustable range: -1.00 % to +1.00 %
(0.1% per step)
If the difference in the width D is greater than the
specifications, use the – (minus) key.
If the difference in the width D is smaller than the
specifications, use the + (plus) key.
35. Touch “Test Copy.”
36. Select the tray loading paper for the test copy.
37. Touch “2.”
38. Touch “2-Sided -> 2-Sided.”
39. Place the chart in the document feeding tray.
(Make sure that the blank surface of the chart
faces up.)
40. Press the start key, and check the difference in
the width D between the chart and the discharged copy sample.
41. Touch “END” twice.
42. Touch “Exit” on the Service Mode screen.
43. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
Mode screen and wait for 10 seconds or more
before turning on.
A3CFIXC028DA
5. Press the Start key.
6. Check that “Adjustment Result” is “OK.”
7. Touch “END.”
XXI. Adjusting the document stop position
<Sub Scanning Direction 1-side/ Sub Scanning
Direction 2-side>
Note:
Perform this adjustment if necessary.
1. Place the chart in the document feeding tray (with
the side having an arrow facing up).
A3CFIXC013DA
2. Make a single-sided copy sample in full size.
E-17
3. Place the chart in the document feeding tray.
(Make sure that the blank surface of the chart
faces up.)
14. Touch “1-Sided -> 1-Sided” or “2-Sided -> 2Sided.”
15. Place the chart in the document feeding tray.
1-Side: With the side having an arrow facing
up
2-Side: With the blank side facing up
16. Press the start key, and check the difference in
the width B between the chart and the discharged copy sample.
<Main Scanning (Front)/ Main Scanning (Back)>
Note:
Perform this adjustment if necessary.
A3CEIXC039DA
17. Place the chart in the document feeding tray
(with the side having an arrow facing up).
4. Make a duplex copy sample in full size.
5. Check whether the difference in the width B
between the chart and the copy sample is within
the specified range.
Difference in the width B = B of the copy sample –
B of the chart
Specifications: 0 ± 2.0 mm
* If the difference in the width B does not fall within
the specified range, perform the following
adjustment.
A3CFIXC013DA
18. Make a single-sided copy sample in full size.
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “1-Sided -> 1-Sided” and then
press the start key to make a copy sample.
19. Place the chart in the document feeding tray.
(Make sure that the blank surface of the chart
faces up.)
A1DMIXC017DA
6. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
7. Touch “ADF.”
8. Touch “Original Stop Position.”
9. Touch “Sub Scanning Direction 1-Side” or “Sub
Scanning Direction 2-Side.”
10. While looking at the copy sample, enter a value
using the ten-key pad on the touch panel. (To
switch the signs, press the +/- key.)
Adjustable range: -4.0 mm to +4.0 mm
(0.1 mm per step)
If the difference in the width B is greater than the
specifications, enter a positive (+) value.
If the difference in the width B is smaller than the
specifications, enter a negative (-) value.
11. Touch “Test Copy.”
12. Select the tray loading paper for the test copy.
13. Touch “2.”
A3CEIXC039DA
E-18
20. Make a duplex copy sample in full size.
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “2-Sided -> 2-Sided” and then
press the start key to make a copy sample.
21. Check whether the difference in the width A
between the chart and the copy sample is within
the specified range.
Difference in the width A = A of the copy sample
– A of the chart
Specifications: 0 ± 2.0 mm
* If the difference in the width A does not fall within
the specified range, perform the following
adjustment.
<Front>
31. Press the start key, and check the difference in
the width A between the chart and the discharged copy sample.
32. Touch “END” twice.
33. Touch “Exit” on the Service Mode screen.
34. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
Mode screen and wait for 10 seconds or more
before turning on.
Note:
When the dual scan document feeder/reverse
automatic document feeder is adjusted in service mode, “Adjustments list” should be output
again as necessary. (Refer to E-11 “XV. List output.”)
<Back>
XXII. Affixing the label (Legal restrictions
on copying)
A1DMIXC016DA
A1DMIXC019DA
22. Display the Service Mode screen, and touch
“ADF.”
Note:
If the Test Copy screen on the Service Mode is
displayed, touch “END” twice.
Affix the label (Legal restrictions on copying) to the
position shown below.
Note:
This step may not be performed depending on the
applicable marketing area.
Label
23. Touch “Original Stop Position.”
24. Touch “Main Scanning (Front)” or “Main Scanning (Back).”
25. While looking at the copy sample, enter a value
using the ten-key pad on the touch panel. (To
switch the signs, press the +/- key.)
Adjustable range: -4.4 mm to +4.4 mm
(0.1 mm per step)
If the difference in the width A is greater than the
specifications, enter a positive (+) value.
If the difference in the width A is smaller than the
specifications, enter a negative (-) value.
26. Touch “Test Copy.”
27. Select the tray loading paper for the test copy.
28. Touch “2.”
29. Touch “1-Sided -> 1-Sided” or “2-Sided -> 2Sided.”
30. Place the chart in the document feeding tray.
Front: With the side having an arrow facing up
Back: With the blank side facing up
A2XKIXE030DA
E-19
XXIII. Changing the stopper position
XXV. Check through test print
1. Raise the two hinge covers on the back of the
dual scan document feeder and remove the stopper from the hinge of the dual scan document
feeder.
2. Change the set position of the stopper to the
upper side and secure it in position.
Make operation checks using “Setting Information
Print.”
1. Select the function to be used as follows:
Menu → Utility → User Settings → Printer Settings → Print Reports.
The types of the test prints that can be printed will
be displayed.
2. Touch “Configuration Page.”
3. Touch A4 size and press the start key.
Check that the machine produces the corresponding printed page.
4. Touch “Cancel” and then touch “Close” four
times.
Stopper
XXVI. Connecting the network cable
1. Connect the networking equipment (HUB) using
the network cable.
Note:
The following shows the recommended network
cables that correspond to each communication
speed.
• 10BaseT/100BaseTX: Category 5
• 1000BaseT: Category 5E, Category 6
LED1
A3CEIXE047DB
XXIV. Affixing the paper size label
Affix the paper size labels that correspond to the
sizes of paper used in each tray.
Networkport
LED2
A5C1IXC008DB
2. Check LEDs for lighting conditions.
LED1:
Should light up steadily if the link network connection has been made.
LED2:
Should blink according to the communications
status of the ACT network.
Paper size label
A161IXC026DA
For loading the paper as well as setting the paper
type, refer to the user’s guide.
E-20
<When adding no paper feed options/desk or when using
the desk DK-705>
4. Remove the knockout from the rear right cover
removed in step 3 using nippers.
3. Remove the indicated knockout from the
machine’s interface cover using nippers.
A161IXC057DA
A161IXC027DB
4. Route the network cable through the harness
guides and pass it through the notch cut in step 3.
Note:
Leave an appropriate amount of slack in the portion of the cable between the plug and the top harness guide in a manner which does not interfere
with the opening and closing of the cover.
5. Route the network cable through the harness
guides and three wire saddles.
Note:
Leave an appropriate amount of slack in the portion of the cable between the plug and the top harness guide in a manner which does not interfere
with the opening and closing of the cover.
Leave an appropriate amount of slack.
Leave an appropriate amount of slack.
A5C1IXC009DB
<When using the paper feed cabinet PC-110/PC-210/PC-410
or desk DK-510>
3. Remove the rear right cover from the paper feed
cabinet or desk. (Two screws)
A5C1IXC010DB
6. Route the cable through the notch cut in step 4
and attach the rear right cover. (Two screws)
A161IXC056DA
A161IXC058DA
E-21
XXVII. Performing Non-Image Area Erase
Check
Note:
Perform the below at the site where customer
uses the machine.
1. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
2. Select the Non-Image Area Erase Check function
as follows:
Machine → Non-Image Area Erase Check.
Note:
• <C554e/C454e>
Open fully the dual scan document feeder.
<C364e/C284e/C224e>
Open fully original options if loaded.
• Do NOT place a document on the document
glass.
• Clean the document glass if dirty.
XXVIII. Network setting
Make the TCP/IP address setting for the network.
Note:
Consult the network administrator for the setting
value to be entered and make settings as
required.
1. Select the function to be used as follows:
Menu → Utility → Administrator Settings → Enter
the Administrator Password → Network Settings
→ TCP/IP Settings → IPv4 Settings.
2. Touch “Manual Input” of IP Address Setting
Method and make the following settings.
IP Address: IP address of the controller
Subnet Mask: Subnet mask of the network, to
which the machine is connected
Default Gateway: IP address of the default gateway
3. Touch “OK” twice.
4. Select the function to be used as follows:
Forward → Detail Settings → PING Confirmation,
and make the operation check of TCP/IP.
Note:
After completing all the steps, take a sample
copy in color mode, and confirm the image. If
image troubles occur, first turn OFF and ON the
Main Power Switch, and then redo the steps
from E-11 “XII. Date & Time Setting/Time Zone
Setting (Service Mode)” to E-11 “XV. List output.”
A161IXC020DA
3. Press the Start key.
4. Make sure that “Result” is “OK.”
Note:
If “Result” is “NG1” or “NG2”, review the place and
direction of installation, or take measures to block
the light source (by covering it, etc.), then perform
installation checking again.
(If a fluorescent light or other bright light sources
exist right above the machine, the light source can
hinder installation checking and cause operation
errors in the Non-Image Area Erase Check. For
detailed information, see the service manual.)
5. Touch “OK.”
6. Touch “Exit” on the Service Mode screen.
7. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
Mode screen and wait for 10 seconds or more
before turning on.
E-22
XXIX. Adjusting registration of paper
source options
10. If the measured width A falls outside the specified range, enter the correction value using the
or
key.
Note:
Performing this procedure is necessary only when
the paper feed cabinet PC-110/PC-210/PC-410 is
installed.
*
1. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
2. Select the function to be used as follows:
Machine → Printer Area → Printer Image Centering Side 1 → 3rd.
3. Press the start key.
A test print will be produced.
4. Measure width A of the test pattern on the backside of the test print produced and check that it
falls within the specified range.
Specifications: 3.0 mm ± 1.0 mm
When the tray 4 is available with the optional
paper feed cabinet, check the tray and make
adjustments in the same way.
11. Produce another test print and check to see if
width A falls within the specified range.
12. Touch “END.”
13. Touch “Exit” on the Service Mode screen.
14. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
Mode screen and wait for 10 seconds or more
before turning on.
XXX. Installing the user’s guide holder
Install the user’s guide holder.
A
Paper exit
direction
4061IXC152DA
5. If the measured width A falls outside the specified
range, see the installation manual of each paper
feed cabinet and make adjustments.
6. Produce another test print and check to see if
width A falls within the specified range.
7. Select the function to be used as follows:
Prt. Image Center. Side 2 (Dup) → 3rd.
8. Press the start key.
A test print will be produced.
9. Measure width A of the test pattern on the backside of the test print produced and check that it
falls within the specified range.
Specifications: 3.0 mm ± 2.0 mm
A61DIXC016DB
XXXI. Affixing the panel sheet
Affix the supplied panel sheet to the surface of the
operation panel.
Note:
• The panel sheet is affixed on customer request.
• The panel sheet must be kept by the customer.
A
Paper exit
direction
A161IXC050DA
4061IXC152DA
E-23
XXXII. Installing the output tray (OT-506)
(C554e/C454e only)
4. Attach the guide supplied with the output tray to
the machine.
1. Check whether the output tray has the snap-fit
hook illustrated below or not.
< With the snap-fit hook >
➁
➀
A2XKIXC032DA
5. Install the output tray.
< With the snap-fit hook >
A5C1IXC026DA
< Without the snap-fit hook >
A5C1IXC028DA
A5C1IXC027DA
< Without the snap-fit hook >
< If the machine has the snap-fit hook >
Go to step 4.
< If the machine does not have the snap-fit hook >
Go to step 2.
2. Open the upper and lower front door of the
machine.
3. Remove the upper left cover from the machine.
(Three screws)
A2XKIXC022DB
6. Reattach the upper left cover removed in step 3
to the machine. (Three screws)
7. Close the upper and lower front door of the
machine.
A2XKIXC021DA
E-24
SP-501 Stamp Unit
INSTALLATION MANUAL
Applied Machines: C554e/C454e
COLOR MFP: 55 ppm/45 ppm
Product Code: A5AY/A5C0
I. Accessory parts
No.
Name
Shape
Q’ty
4. Remove the cover shown in the illustration.
(Two screws)
1. Stamp unit
1
4614U001AA
2. Stamp
1
4614U002AA
3. Installation
manual
1 set
A3CEIXC025DA
4980IXC019DA
5. Remove the ground terminal. (One screw)
6. Remove the connector fastened to the guide
plate.
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
II. Installation procedures
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Raise the dual scan document feeder.
3. To detach the left side of the document pad from
the feeder, separate the two faces of the hookand-loop fastener (at two places on the left).
Note:
When removing the document pad, pull apart the
hook and loop fastener one by one. Pulling the
mall at once may damage the sponge.
A3CEIXC026DA
7. Remove the guide plate. (One screw)
A3CEIXC027DA
A3CEIXC024DA
E-25
8. Remove the ground terminal. (One screw)
13. Route the ground terminal through the hole
shown in the illustration and attach the guide
plate to the dual scan document feeder.
(One screw removed in step 7)
Screw
A3CEIXC028DA
9. Mount the supplied stamp in stamp unit.
Note:
Align the round pin of the stamp with the slit in the
stamp unit side.
A3CEIXC030DA
14. Connect the connector of the hookup harness,
and route the hookup harness into the guide.
4614IXC007DA
10. Route the harness through the hole shown in the
illustration.
11. Attach the stamp unit to the guide plate.
(One screw removed in step 8)
Note:
Ensure that the ground terminal is on the upper
side of the mounting bracket of stamp unit.
A3CEIXC031DA
Route the harness through the hole.
A3CEIXC029DA
12. Fasten the harness to the guide located on the
back of the guide plate.
15. Attach the end of the ground terminal to the
place where it was removed in step 5.
(One screw removed in step 5)
16. Reinstall the cover that have been removed in
step 4. (Two screws)
17. Securely attach the document pad by pressing it
against the feeder by hands.
Note:
Make sure that there is no misalignment and slack
in the document pad.
18. Close the dual scan document feeder.
III. Setting
A3CEIXC042DA
1. Plug the power cord into the power outlet and
turn on the machine.
2. Display the Service Mode screen.
(For details of how to display the Service Mideastern, see the service manual.)
3. Touch “System 2.”
4. Touch “Stamp.”
5. Touch “Set.”
6. Touch “END.”
7. Touch “Exit” on the Service Mode screen.
E-26
OC-511 Original Cover
INSTALLATION MANUAL
Applied Machines: C364e/C284e/C224e
COLOR MFP: 36 ppm/28 ppm/22 ppm
Product Code: A5C1/A5C2/A5C4
I. Accessory parts
No.
Name
II. Installation procedures
Shape
Q’ty
1. Original cover
1. Remove the two knockouts using nippers or a
similar tool.
1
A161IXC060DA
2. Hinge cover
(right)
1
A161IXC031DA
3. Hinge cover
(left)
1
A161IXC032DA
4. Screw
(3 x 8 mm)
A161IXC033DA
2
V1160308
2. Attach the supplied hinge cover (right) and hinge
cover (left).
(Two screws supplied with the original cover)
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
A161IXC034DA
3. Install the original cover.
A161IXC035DA
E-27