NEMCO STEAMER
Model Series: 6600
OPERATING INSTRUCTIONS
INTRODUCTION
1. Read These Operating Instructions thoroughly before installing or using this Equipment. Improper installation or use can result in
equipment or property damage, electric shock or personal injury.
2. Nemco Steamers are heavy duty and are designed for commercial use.
3. Only trained personnel should operate this equipment.
SAFETY INSTRUCTIONS
1. IMPORTANT: Clean machine thoroughly before first use and after all uses, using cleaning instructions below.
2. IMPORTANT: Incoming power MUST be the same as the equipment’s rating. Refer to the Electrical Ratings listed on the
equipment’s Data Tag Located on the side of the unit.
3. CAUTION: This unit’s power cord is equipped with a GROUNDED, 3-prong power cord. Plug only into a matching, grounded outlet.
DO NOT cut or break off the third prong. Operating this equipment without proper grounding may result in electric shock.
4. CAUTION: Always disconnect Power when not in use and before cleaning or servicing.
5. CAUTION: Do not operate with a damaged cord or plug or after the machine malfunctions, has been dropped or damaged. Use
authorized service for examination, electrical or mechanical adjustment or repair.
6. CAUTION: Equipment surfaces are HOT during use and a short time after disconnecting the power. Allow to cool before moving or
servicing.
7. WARNING: DO NOT immerse in water or other liquid. DO NOT clean with water jet. SEVERE personal injury or death can result.
ELECTRICAL REQUIREMENTS
1. The electrical ratings are listed on the equipment’s Data Tag located on the side of this equipment.
2. Model 6600 is rated 120 Volts, 1800 Watts, 15Amps and has a NEMA 5-15P plug and grounded cord.
3. This equipment must be properly GROUNDED.
Note: This unit is equipped with a Hi-Limit reset button (located on the rear of the unit). To reset this thermostat, unplug the unit
and allow unit to cool for approximately 45 minutes. Remove cap located on the reset switch and fully press the reset button and
reinstall cap.
PREPARATION
1.
2.
3.
4.
5.
6.
7.
8.
Remove all packing pieces and lift unit out of the box.
Remove any outside packaging.
Set unit on a flat surface. REFER to SAFETY INSTRUCTIONS No. 1 above.
Position unit near the power outlet. Avoid the use of extension cords. Do not run cord under carpeting or cover with runners or the
like. Arrange cord where it will not be tripped over.
This appliance has hot and live electrical parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or
stored.
Unit must be operated with legs installed.
Remove any white plastic coating that may be affixed to exterior surfaces.
If unit fails to work properly when first operated, call NEMCO customer service at 1-800-782-6761.
OPERATION
1.
2.
3.
4.
5.
6.
7.
Plug the unit into the power supply.
Open tank cover and verify that filter inside tank is installed properly. Fill unit with approximately 3 quarts of cold tap water (Do
NOT overfill the tank). Note: 6600 is designed to use cold tap water. Distilled water may be used to reduce calcium/mineral deposit
build-up and reduce maintenance costs.
Turn on/off switch to the on position and allow the unit to preheat for approximately 30 minutes. Note: Do NOT push the operate
button during warm-up.
Open the top cover and place the product to be steamed onto the Trivet and then close the top cover.
Press the OPERATE button for 1 second then release and wait 20 seconds for the steam to penetrate the product. Repeat if product
requires more steam. Note: Pressing and holding the OPERATE button for longer than 1 second at a time and/or to often will flood
out the generator surface and result in poor steaming.
Remove steamed product.
To disconnect appliance, turn switch to off and remove plug from outlet.
WARNING: DURING NORMAL OPERATION, THE EXTERIOR OF THE UNIT IS HOT.
10/06/10
11
10110691011069
Rev: BRev. D 03/12
2
1011069 Rev. D 03/12
Figure A - Steamer Components
Trivet
Pan
Top Cover
Assy.
Gasket
Hinge Pin
Diffuser
Spray
Tube
Assy.
Steam
Generator
Surface
Figure B - Hi Limit Reset
Reset
Button
Cap
3
1011069 Rev. D 03/12
Exploded View 6600
20
17
12
18
1
10
14
9
4
1011069 Rev. D 03/12
Exploded
View
6600
Exploded
View
6600
See Inset B
11
15
See Inset A
13
Inset A
9
Inset B
3
4
16
6
5
ES
UN
ANT
T6
T5
E IN
MAD
R18
CR5
C3
R1
R9
C1
4
023
00-
PCB
T2
.
NO
T3
R5
+
R16
USA
IAL
SER
R8
+
R11
CR4
CR2
+C5
VR1
C6
R10
CR1
CR6
R2
R15
R4
C4
R13
R6
T4
U1
R14
T1
R12
2
7
8
Service
Parts
List
6600
Service
Parts
List
6600
Item
Part No.DescriptionQty.
Used
Part No.
Description
Qty Used
1.
68782Spray Tube Assembly1
1.
68782
Spray Tube Assembly
1
2.
68783Transformer1
2.
68783
Transformer
1
3.
68784Pump1
3.
68784
Pump
1
4.
68785Control Board1
4. 68785
Control Board
1
5.
68786Rocker Switch1
5. 68786
Rocker Switch
1
6.
68787Momentary
Switch1
6.
68787
Momentary Switch
1
7.
68788Hi-Limit
Thermostat1
7.
68788
Hi Limit Thermostat
1
8.
68789Solid
Relay1
8.
68789
Solid StateState
Relay
1
9.
68790
Thermistor
1
9.
68790Thermistor1
10.
68791
Generator
1
10.
68791Generator1
11.
68792
Water
Tank
Filter
1
11.
68792Water Tank Filter1
12. 68793
Cover Gasket
1
12.
68793Cover Gasket1
13. 68794
Silicone Tube Kit
1
13.
68794Silicone
Tube Kit1
14. 68795
Generator Tube
1
14.
68795Generator
Tube1
15.
68796
Water Tank / Cover
Assembly
1
15. 68797
68798-1 Control
Water
TankLabel
/ Cover Assembly 1 1
16.
Panel
17.
68798
Top Cover Assembly
1
16.
68797Control
Panel Label1
18.
68799
Trivet Cover Assembly1
1
17.
68798Top
19.
68800
Silicone High Temperature
1
18.
68799Trivet1
19.
68800Silicone High Temperature1
Item
NEMCO FOOD EQUIPMENT 301 Meuse Argonne, Hicksville, OH 43526
1-800-782-6761 Toll Free 419-542-6690 Fax
www.nemcofoodequip.com
5
10/06/10
5
1011069 Rev. D 03/12
1011069 Rev: B