QK-DMKEY1
QK-KEY1
Waterproof Keypad/Reader/Controller
User Manual
V02/12
1. Packing List
Name
Digital Keypad QK-DMKEY1
Quantity
1
Remarks
User manual
1
Screw driver
1
Rubber bungs
4
6*27mm, used for fixing
Self tapping screws
4
3.5*27mm, used for fixing
Manager Card
2
Manager Add Card & Manager Delete Card
Please ensure that all the above contents are correct. If any are missing please notify the
supplier of the QK-DMKEY1.
2.
Description
The QK-DMKEY1 is single door multifunction standalone access controller or a Wiegand
output keypad or card reader. It is suitable for mounting either indoor or outdoor in harsh
environments. It is housed in a strong, sturdy and vandal proof Zinc Alloy electroplated
case. The electronics are fully potted so the QK-DMKEY1 is waterproof and conforms to
IP68.
The QK-DMKEY1 supports up to 2000 users in either a Card, 4~8 digits PIN, or a Card +
PIN option. The built-in card reader supports EM 125KHZ frequency cards/tags. The
QK-DMKEY1 has many extra features including block enrollment, Wiegand 26 bits
interface, and backlit keypad.
These features make QK-DMKEY1 an ideal choice for door access not only for small
shops and domestic households but also for commercial and industrial applications such
as factories, warehouses, laboratories, banks and prisons.
3.
Features
z
Waterproof, conforms to IP68
z
Strong Zinc Alloy Electroplated anti-vandal case
z
Full programming from the keypad
z
2,000 users, supports Card, PIN, Card + PIN
z
Can be used as a stand alone keypad, Pin length 4~8 digits
z
Backlight keypad
z
Wiegand 26 bit input & output
z
One programmable Relay output, NO, NC, COM
z
Adjustable Door Output time, Alarm time, Door Open time
z
Block enrollment, can enroll maximum 2000 consecutive card within 2 minutes
z
Very low power consumption (<60mA)
z
Easy to install and program
www.quikoitaly.com
2
z
Built in light dependent resistor (LDR) for anti tamper
z
Built in buzzer
z
Red, Yellow and Green LEDs display the working status
z
12~24VDC – 12-18VAC
z
Two-year warranty
4.
Specifications
Operating Voltage
12~24V DC – 12-18V AC
User Capacity
2,000
Keypad
12 keys, 3 x 4 digits
Card Type
EM 125 KHZ card
Card Reading Distance
3~6 cm
Active Current
<80mA
Idle Current
≤40mA
Lock Output Load
Max 2A
Alarm Output Load
Max 20mA
Operating Temperature
-20~60℃
Operating Humidity
5%~95% RH
Environment
Conforms to IP68
Adjustable Door Relay time
0 ~ 99 seconds
Adjustable Alarm Time
0 ~ 3 minutes
Wiegand Interface
Wiegand 26 input & output
Wiring Connections
Electric Lock, Exit Button, DOTL, External Alarm
Dimensions
L128 x W82 x H28 mm
Net Weight
550 g
Gross Weight
700 g
www.quikoitaly.com
3
5. Installation
z
Remove the back cover from the keypad using the supplied security screwdriver
z
Drill 4 holes on the wall for the screws and I hole for the cable
z
Fix the back cover firmly on the wall with 4 flat head screws
z
Thread the cable through the cable hole
z
Attach the keypad to the back cover.
6. Wiring
Color
Function
Description
Green
D0
Wiegand Output D0
White
D1
Wiegand Output D1
Grey
Alarm -
Alarm Negative
Yellow
OPEN
Request to Exit Button
Brown
D-In
Door Contact
Red
Power supply
Regulated Power Input
Black
Power supply
Regulated Power Input
Blue
NO
Relay NO
Purple
COM
Relay COM
Orange
NC
Relay NC
Pink
GND
External Reader Negative
www.quikoitaly.com
4
Connection Diagram
Power positive
Alarm
Pink
Green
Power supply
White
12-14VDC / 12-18 VAC
Grey
Exit button
Yellow
Door contact
Brown
Red
Black
Blue
Violet
Lock negative power
Orange
QK-DMKEY1
Power positive
Lock
To contact
N.C. or N.O
Notes:
Connect the negative pole of the lock to NC is for Fail safe lock.
Connect the negative pole of the lock to NO is for Fail-secure lock.
www.quikoitaly.com
5
7.
To Reset to Factory Default
To reset to factory default, power off, press
*
, hold it and power on, release it until hear two
beeps and the LED shines in orange, then read any two EM cards, the LED will turn in red,
means reset to factory default setting successfully. Of the two EM cards read, the first one is
Manager Add card, the second one is Manager Delete card.
Remarks: Upon reset to factory default, the user’s information is still retained.
8. Anti Tamper Alarm
The QK-DMKEY1 uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad
is removed from the cover then the tamper alarm will operate.
9. Sound and Light indication
Operation Status
Red Light
Green Light
Yellow Light
Buzzer
Power on
Bright
-
-
Short Ring
Stand by
Bright
-
-
-
Press keypad
-
-
-
Short Ring
Operation successful
-
Bright
-
Short Ring
Operation failed
-
-
-
3 Short Rings
Bright
-
-
Short Ring
In the programming mode
-
-
Bright
-
Exit from the programming
Bright
-
-
Short Ring
-
Bright
-
Short Ring
Bright
-
-
Alarm
Enter into programming mode
mode
Open the door
Alarm
www.quikoitaly.com
6
10.
QK-DMKEY1 Detailed Programming Guide
10.1
User Settings
To enter the programming mode
*
Master code #
888888 is the default factory master code
To exit from the programming mode
*
Note that to undertake the following programming the master user must be logged in
To change the master code
0
New code
#
New code #
The master code is any 6 digits
Setting the working mode:
Set valid card only users
3
0
#
Entry is by card only
Set valid card and PIN users
3
1
#
Entry is by card and PIN together
Set valid card or PIN users
3
2
#
Entry is by either card or PIN
(default)
To add a user in either card or PIN mode ( 3
To add a Pin user
1
2
#
) (Default setting)
User ID number
#
PIN #
The ID number is any number between 1 ~ 2000.
The PIN is any 4~8 digits between 0000 ~ 99999999
with the exception of 1234 which is reserved. Users
can be added continuously without exiting from
programming mode as follows:
To delete a PIN user
1
User ID no 1 #
PIN # User ID no 2 #
2
User ID number
PIN #
#
Users can be deleted continuously without exiting
programming mode
To change the PIN of a PIN user
(This step must be done out of
*
ID number #
Old PIN #
New PIN #
New
PIN #
programming mode)
To add a card user (Method 1)
1
This is the fastest way to enter cards
Cards can be added continuously without exiting
using ID number auto generation.
programming mode
To add a card user (Method 2)
1
Read card
ID number
#
#
Card
#
This is the alternative way to enter
cards using User ID Allocation. In this
www.quikoitaly.com
7
method a User ID is allocated to a card.
Only one user ID can be allocated to a
single card.
5
To add card user (Method 3)
Add a series cards users – Block
ID number
quantity
#
8 digits Card number
# Card
#
Card quantity is between 1 ~ 2000. The 8 digits card
Enrollment
number is the last 8 digits on the card.
Maximum 2000 cards can be enrolled at a stretch
within 2 minutes.
To delete a card user by card number.
Note
users
continuously
can
be
without
2
Read Card
#
deleted
exiting
programming mode
2
To delete a card user by user ID. This
User ID
#
option can be used when a user has
lost their card
To add a card and PIN user in card and PIN mode ( 3
1
#)
To Add a card and Pin user
Add the card as for a card user
(The PIN is any 4~8 digits between
Press
0000 & 99999999 with the exception of
Then allocate the card a PIN as follows:
1234 which is reserved.)
To change a PIN in card and PIN mode
(Method 1) Note that this is done
*
to exit from the programming mode
*
Read card 1234 # PIN # PIN #
*
Read Card
Old PIN #
New PIN #
New
PIN #
outside programming mode so the user
can undertake this themselves
*
To change a PIN in card and PIN mode
(Method 2) Note that this is done
ID number #
Old PIN #
New PIN #
New
PIN #
outside programming mode so the user
can undertake this themselves
2
To delete a Card and PIN user just
User ID
#
delete the card
To add a card user in card mode ( 3
To Add and Delete a card user
0
#)
The operating is the same as adding and deleting a
card user in 3
2
#
To delete All users
www.quikoitaly.com
8
2
To delete ALL users. Note that this is a
0000
#
dangerous option so use with care
To set card users by Manager card
Manager add card Read card Manager add card
To add user by Manager Add Card
Cards can be added continuously.
To delete User by Manager Delete Card
Manager delete card Read Card
Manager delete card
Cards can be deleted continuously.
To unlock the door
For a PIN user
Enter the PIN
then press #
For a card User
Read card
For a card and PIN user
Read card then enter PIN #
10.2 Door Relay, Door Detecting, Alarm Settings
Door relay time setting
To set door relay strike time
4
0~99
#
The door relay time is between 0~99 seconds, the factory default
setting is 5 seconds.
Door Open Detection
Door Open Too Long (DOTL) warning. When used with an optional magnetic contact or built-in
magnetic contact of the lock, if the door is opened normally, but not closed after 1 minute, the inside
buzzer will beep automatically to remind people to close the door and continue for 1 minute before
switching off automatically.
Door Forced Open warning. When used with an optional magnetic contact or built-in magnetic contact
of the lock, if the door is opened by force, or if the door is opened after 20 seconds of the
electro-mechanical lock not closed properly, the inside buzzer and alarm output will both operate. The
Alarm Output time is adjustable between 0~3 minutes with the default being 1 minute.
To disable door open detection.
6
0
#
6
1
#
9
0~3
(Factory default)
To enable door open detection
Alarm output time
To set the alarm output time (0~3
www.quikoitaly.com
#
9
minutes) Factory default is 1 minute
Keypad Lockout & Alarm Output options. If there are 10 invalid cards or 10 incorrect PIN numbers
in a 10 minute period either the keypad will lockout for 10 minutes or the alarm will operate for 10
minutes, depending on the option selected below.
Normal status: No keypad lockout or
7
0
# (Factory default setting)
Keypad Lockout
7
1
#
Alarm Output
7
2
#
alarm (factory default)
To remove the alarm
To reset the Door Forced Open warning
To reset the Door Open Too Long warning
Read valid card or Master Code #
Close the door or
Read valid card or Master Code #
11.
Interconnecting Two Devices
11.1
QK-DMKEY1 operating as a Wiegand Output Reader
In this mode the QK-DMKEY1 supports a Wiegand 26 bit output so the Wiegand data lines
can be connected to any controller which supports a Wiegand 26 bit input. See figure 1.
Pink
Green
White
Red
Power supply
Controller
(with Wiegand 26 bit input)
QK-DMKEY1
Figure 1
www.quikoitaly.com
10
Transmission Format:
◆ 1: Keypad Transmission
The Reader will transmit the PIN data when it receives the last key (#) press after PIN code.
Format: PIN Code (any 4~8 digits between 0000 ~ 99999999)
Example: PIN code: 111111
Press 111111 #, then the output format will be: 00111111
(Note: if press an invalid PIN (any 4~8 digits), the data will be also transmitted.)
◆ 2: Proximity Card Transmission
The Reader will transmit the card data when it reads the Card.
Format: Card Number (the last 8 digits of Card Number)
(Note: no matter the card is valid or invalid, the data will be transmitted)
11.2
QK-DMKEY1 operating as a Controller
In this mode the QK-DMKEY1 supports a Wiegand 26 bit input so an external Wiegand
device with a 26 bit output can be connected to the Wiegand input terminals on the
QK-DMKEY1. Either an ID card reader (125 KHZ) or an IC card reader (13.56MHZ) can be
connected to the QK-DMKEY1. Cards are required to be added at the external reader, except
where an external EM reader is used, in this case cards can be added at either reader or
controller. See figure 2.
Power supply
Reader with 26 bit
Wiegand output
Pink
Green
White
Grey
Exit button
Yellow
Brown
Door contact
Red
Black
Blue
Violet
Orange
QK-DMKEY1
www.quikoitaly.com
Figure 2
11
QK-DMKEY1 Quick Reference Programming Guide
To enter the programming mode
*
Master code
#
888888 is the default factory master code
To exit from the programming mode
*
Note that to undertake the following programming the master user must be logged in
To change the master code
0
New code
#
New code
#
The master code can be 6 digits long
To add a PIN user
1
User ID number
#
PIN #
The ID number is any number between 1 ~ 2000. The
PIN is any 4~8 digits between 0000 ~ 99999999 with the
exception of 1234 which is reserved. Users can be added
continuously without exiting programming mode
To add a card user
1
Read Card
#
Cards can be added continuously without exiting from
programming mode
To delete a PIN or a card user.
2
User ID number
2
Read Card
#
#
for a PIN user or
for a card user
Users can be deleted continuously without exiting from
programming mode
To unlock the door
To unlock the door for a PIN user
Enter the PIN then press #
To unlock the door for a card user
Present the card
www.quikoitaly.com
12
Download PDF