R
INSTALLATION
AND
OPERATING
INSTRUCTIONS
roiler
ot Dog B older
H
A
-2
R
D
Bun H
Model
al BH-1A
n
o
i
t
p
O
With
MERCHANDISERS
Models:
DS-1A, DR-1A, BH-1A
INTENDED FOR OTHER THAN HOUSEHOLD USE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or Parts, this information is required.
Model Number
!
Serial Number
Date Purchased
WARNING: For your safety do not store or use gasoline or other flammable vapors or liquids in the
vicinity of this or any other appliance. Keep the area free and clear of combustibles. (See ANZI
Z83.14B, 1991)
!
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the Installation, Operating and
Maintenance Instructions thoroughly before installing or servicing this equipment.
!
!
This equipment has been engineered to provide you with year-round dependable service when used
according to the instructions in this manual and standard commercial kitchen practices.
P/N 457213-00 2/08
Phone:
Fax:
Toll Free:
Website:
E-mail:
+1 (307) 634-5801
+1 (307) 637-8071
+1 (800) 752-0863
www.apwwyott.com
info@apwwyott.com
APW WYOTT
P.O. Box 1829
Cheyenne, WY 82003
1
APW Wyott takes pride in the design and quality of our products. When used as intended and with proper
care and maintenance, you will experience years of reliable operation from this equipment. To ensure best
results, it is important that you read and follow the instructions in this manual carefully.
Installation and start-up should be performed by a qualified installer who thoroughly read, understands and
follows these instruction.
If you have questions concerning the installation, operation, maintenance or service of this product, write
Technical Service Department APW/Wyott Foodservice Equipment Company, P.O. Box 1829, Cheyenne,
WY 82003.
SAFETY PRECAUTIONS
Before installing and operating this equipment be sure everyone involved in its operation are fully trained
and are aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules
and precautions.
The following words and symbols, found in this manual, alert you to hazards to the operator, service
personnel or the equipment. The words are defined as follows:
!
DANGER: This symbol warns of imminent hazard which will result in serious injury or death.
!
!
WARNING: This symbol refers to a potential hazard or unsafe practice, which could result in
serious injury or death.
!
!
CAUTION: This symbol refers to a potential hazard or unsafe practice, which may result in minor or
moderate injury or product or property damage.
!
!
NOTICE: This symbol refers to information that needs special attention or must be fully understood
even though not dangerous.
!
!
CAUTION: These models are designed, built, and sold for commercial use. If these models are
positioned so the general public can use the equipment make sure that cautions, warnings, and
operating instructions are clearly posted near each unit so that anyone using the equipment will
use it correctly and not injure themselves or harm the equipment.
!
!
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause
property damage, injury or death. Read the Installation, Operating and Maintenance Instructions
thoroughly before installing or servicing this equipment.
!
!
WARNING: Install per the spacing requirements listed in the installation section of this manual. We
strongly recommend having a competent professional install the equipment. A licensed electrician
should make the electrical connections and connect power to the unit. Local codes should always
be used when connecting these units to electrical power. In the absence of local codes, use the
latest version of the National Electrical Code.
!
!
WARNING: For your safety do not store or use gasoline or other flammable vapors or liquids in the
vicinity of this or any other appliance. Keep the area free and clear of combustibles. (See ANZI
Z83.14B, 1991)
!
!
NOTICE: Instructions to be followed if anyone smells gas should be posted in a prominent place.
These may be obtained from the gas supplier.
!
WARNING: Check the data plate on this unit before installation. Connect the unit only to the voltage
and frequency listed on the data plate. Connect only to 1 or 3 phase as listed on the data plate.
!
!
2
!
WARNING: Disconnect device from electrical power supply and place a Tag Out-Lockout on the
power plug, indicating that you are working on the circuit.
!
!
CAUTION: Maintenance & repair should be handled by a factory authorized agent. Before doing
any maintenance or repair, contact APW Wyott.
!
CONTENTS
Safety Precautions
General Information & Troubleshooting
DS-1A Mr. Frank Display Steamer
DR-1A Mr. Frank Display Broiler w/BH-1A Bun Warmer
Wiring Diagrams: DR-1A, DR-2A and DS-1A
2
3
4
5
5
Parts Lists & Exploded Views
DR-1A, DR-2A, BH-1A
DS-1A
Warranty
6
6
7
8
LOCATION OF DATA PLATE
The data plate is located on the back of the unit.
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All containers should be examined for damage before and during unloading. The freight carrier has
assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent
or concealed, a claim must be made with the delivering carrier.
A)
Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then
be signed by the carrier representative (Driver). If this is not done, the carrier may refuse the
claim. The carrier can supply the necessary forms.
B)
Concealed damage or loss if not apparent until after equipment is uncrated, a request for
inspection must be made to the carrier within 15 days. The carrier should arrange an
inspection. Be certain to hold all contents and packaging material.
Installation and start-up should be performed by a qualified installer who thoroughly read, understands and
follows these instructions.
GENERAL INFORMATION & TROUBLESHOOTING
!
NOTICE: The unit when installed, must be electrically grounded and comply with local codes, or in
the absence of local codes, with the national electrical code ANSI/NFPA70- latest edition.
Canadian installation must comply with CSA-STANDARD C.22.2 Number 0 M1982 General
Requirements-Canadian Electrical Code Part II, 109-M1981- Commercial Cooking Appliances.
!
!
NOTICE: Local codes regarding installation vary greatly from one area to another. The National
Fire Protection Association, Inc. states in its NFPA96 latest edition that local codes are “Authority
Having Jurisdiction” when it comes to requirement for installation of equipment. Therefore,
installation should comply with all local codes.
!
General Installation Instructions:
1. Always clean equipment thoroughly before first use. (See general cleaning instructions.)
2. Check rating label for your model designation and electrical rating.
3. Position equipment on level counter and plug into a grounded outlet so the plug is accessible. (See
individual description for electrical loads.) On units bearing the CE marking, the appliance must be
connected by an earthing cable to all other units in the complete installation and, hence, to an
independent earth connection.
3
General Operating Instructions:
1. All foodservice equipment should be operated by trained personnel.
2. Do not allow your customers to come in contact with any surface labeled “CAUTION HOT.”
3. Where applicable, never pour cold water into dry heated units.
4. Where applicable, do not cook, warm or hold food directly in liner pans (well pans). Always use
steam table pans/insets, etc.
5. Never hold food below 150°F (66°C).
General Cleaning Instructions:
1. NEVER clean any electrical unit by immersing it in water. Unplug unit before surface cleaning.
2. Always clean equipment thoroughly before first use. Clean unit daily. Except where noted on charts,
use warm, soapy water. Mild cleansers and PLASTIC scouring pads may be used to remove bakedon food and water scale.
3. Unplug all units before cleaning or servicing. All service should be performed by an APW authorized
service agency.
4. Do not use chlorides or chloride-based products in this unit. Always clean equipment before first
use. Clean unit daily. Use warm, soapy water. Rinse thoroughly to remove all residue. Chlorides,
chloride-based products and improper cleaning may cause corrosion and pitting.
!
CAUTION: Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your unit,
marring it’s appearance and making it susceptible to dirt accumulation. Do Not use steel wool, other
abrasive cleaners or cleaners/sanitizers containing chlorine, iodine, ammonia or bromine
chemicals as these will deteriorate the stainless steel and glass material and shorten the life of the
unit.
!
!
WARNING: Unit is not waterproof. To avoid electrical shock or personal injury, DO NOT submerge
in water. DO NOT operate if it has been submerged in water. DO NOT clean the unit with a water jet.
DO NOT steam clean or use excessive water on the unit.
!
Failure to comply with these instructions may void unit warranty.
General Troubleshooting—Always ask and/or check:
1. Is the unit plugged in?
2. Check circuit breaker.
3. Is power switch on and pilot light glowing?
4. Check rating label. Are you operating unit on proper voltage?
5. If the supply cord is damaged, it should only be replaced by an identical supply cord.
If the above checks out and you still have problems, call an APW authorized service agency.
DS-1A—MR. FRANK DISPLAY STEAMER
Installation:
1. Follow general installation instructions on page 3.
2. The operator must slide basket in over support pins and support flange.
Operations:
1. Follow general operation instructions on page 4.
2. Pour 3 quarts of hot water, 120°-140°F (50°-60°C), into lower pan. Cap on drain pipe must be finger
tight.
3. Place perforated hot dog tray into lower compartment. Load with up to 150 hot dogs.
4. Heat up time will depend on size and temperature of the hot dogs. Place bun basket into upper
cabinet, slide drip shield on top of bun basket, load up to 60 buns. Buns may be stored in plastic bag
for prolonged holding periods.
5. Turn on unit. Set infinite control to “HI” position to begin steaming.
6. For holding, readjust control to “4” or “5” setting after 15 minutes (or when water steams).
7. Add water to unit if level is low.
Cleaning:
1. Follow general cleaning instructions on page 4.
2. Turn off unit and allow cabinet to cool.
3. Unscrew drain cap and drain water from cabinet.
4. Remove trays, baskets and support shelves from cabinet. Clean thoroughly
4
DR-1A—MR. FRANK DISPLAY BROILER WITH BH-1A BUN WARMER
Installation:
1. Follow general installation instructions on page 3. The broiler is labeled “Caution Hot.” Do not allow
customers to come in contact with the hot surface.
2. Insert basket holder assembly into cabinet by placing shaft end into spring loaded fitting. Connect
slotted coupling end over motor shaft by compressing spring loaded fitting.
3. Place individual baskets into support holes on hold assembly. Open side of basket should always
face operator.
4. Slide drip pan into cabinet under the basket assembly.
5. If optional bun warmer is used, place warmer into opening on top of broiler.
Operations:
1. Follow general operating instructions on page 4.
2. Switch on unit. Set infinite control to “HI” position to begin broiling.
3. Load each basket with up to 4 hot dogs. Use “Load/Unload” push button.
4. Heat up time will depend on the size and temperature of the hot dogs when loaded into the baskets.
5. For holding, readjust control to “5” or “6” setting after 15 minutes. If control is left on “HI,” hot dogs will
blister. To display hot dogs for several hours without shriveling or flavor loss, Do Not Pierce Casings.
6. If optional bun warmer is used, pour 1 quart of hot water, 120°-140°F (50°-60°C), into pan. Load up
to 36 buns. Attach drip shield. Buns may be stored in plastic bag for prolonged holding periods.
7. Use LOAD/UNLOAD push button to remove hot dogs from unit.
8. Add water as necessary to maintain moist buns.
Daily Cleaining:
1. Follow general cleaning instructions on page 4 .
WIRING DIAGRAMS
DR-1A, DR-2A
DS-1A
Indicator Light
Lamps 240V, 1Ph
Heating Element
Indicator
Light
Lamps
Gear
Motor
P L1 L2
H1 H2
P L1 L2
H1 H2
Infinite
Control
Infinite
Control
Load/Unload
Switch
On/Off
Switch
Heating Element
240V, 1Ph
Limiting Thermostat
Terminal Block
5
PARTS LISTS w/EXPLODED VIEWS
DR-1A, DR-2A, BH-1A
R
Toll Free:
Website:
Display Hot Dog Broiler
P.O. Box 1829
Cheyenne, WY 82003
Phone:
Fax:
E-mail:
+1 (307) 634-5801
+1 (307) 637-8071
+1 (800) 752-0863
www.apwwyott.com
info@apwwyott.com
HOT DOG ROASTER DR-1A & DR-2A & BUN HOLDER BH-1A
Item Part No.e Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
N/S
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
N/S
37
38
39
40
41
42
43
N/S
N/S
N/S
N/S
N/S
44685200
44685400
44680200
44680100
8967200
44686600
44687000
1506000
2002300
2000300
44687800
44683100
1505800
1196100
47255900
1547000
8968900
48609300
44683800
83006-00
48914500
48521000
1301608
1301602
45582500
48940600
44687500
45653000
44689500
44689100
44685000
44685600
44687400
44681200
45576800
21766800
44688100
44688500
47253300
44689000
44680300
8705000
44674900
446851
446825
446832
446830
446880
Page 2 of 4
Wrapper Assembly
Control Housing
Large Glass
Small Glass
1/2 Inch Hole Bushing
Top Cover
Reflector Assembly
Lamp Holder
Nipple, Lamp Holder
Nut, Lamp Holder
Heating Element 120V
Heating Element 240V
Lamp Bulb
Wire Nut
Cord 120V
Cord 240V
Strain Relief Bushing
Conveyor Motor 120V
Conveyor Motor 240V
Motor Drive Roll Pin
Terminal Block
Conveyor Idler Bearing
Infinite Control 120V
Infinite Control 240V
Knob, Infinite Control
On-Off Switch
Load Push Switch
Indicator Light
Inspection Panel
Conveyor Carousel
Basket (Each)
Drip Pan
Top Hole Cover
Bottom Cover
Foot (Each)
Marketing Label
Wrapper & Top Assembly
Door Assembly
Handle, Door
Bun Basket
Drip Shield
Magnet Door
Magnet Plate, Door (Ralley's)
DR-1A 120V Unit
DR-2A 120V Unit
DR-1A 240V Unit
DR-2A 240V Unit
Bun Holder
41
42
37
43
40
33
39
38
6
7
10
9
12 11
30
8
13
31
5
14
3
24 23
19 18
29
22
2
21
1
28
27 25
17 26
4
32
15 16
34
35
Note: When ordering, ALWAYS specify Part #, Model #, Serial #, Voltage & Phase.
6
P/N 467111-00 Rev. 6/05
+1 (307) 634-5801
+1 (307) 637-8071
+1 (800) 752-0863
www.apwwyott.com
info@apwwyott.com
Phone:
DS-1A
R
Fax:
Toll Free:
Website:
Hot Dog Steamer
P.O. Box 1829
Cheyenne, WY 82003
E-mail:
HOT DOG STEAMER DS-1A
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
N/S
N/S
N/S
N/S
Exploded View
Part No.e Description
44662900 Upper Wrapper Assembly
44680200 Glass
44661100 Bottom Wrapper Assembly
44663100 Door Assembly
44660900 Hot Dog Tray
44689000 Bun Basket
Model
DS-1A
DS-1A
Voltage
240V
120V
2
P/N
442103
446640
7
1
26
44675600 Drip Shield
44661300 Basket Support
6
44681200 Bottom Cover
45576800 Rubber Foot (each)
5
44677500 Drain Cap Assembly
44676100 Drain Cap Only
44675000 Drain Cap Chain
44676200 Rubber Gasket
22
1301608 Infinite Control (120V)
1301602 Infinite Control (240V)
26
45582500 Knob, Infinite Control
45653000 Indicator Light
21
47255900 Cord, Power 120V
47255900 Cord, Power 240V (Remove Plug)
24
23
8968900 Strain Relief Bushing
46910700 High Limit Thermostat
4
25
18
15
3
45596000 Heating Element 120V, 800W
45081700 Heat Transfer Plate
27
19
45569500 Element Clamp
45569600 Anti-Rotation Clamp
16
45599200 Element Cover
21766800 Label, Marketing
14
48970100 Label, Caution Hot
8978400 Hole Bushing 7/8”
11
8422400 10-24 Green Hex Nut
8422300 10-24 Hex Nut
12
48902500 10-24 Speed Nut
8128700 Screw, Drive, Type AB 8-18
Page 2 of 4
8
20
9
17
13
10
Note: When ordering, ALWAYS specify Part #, Model #, Serial #, Voltage & Phase.
7
28
P/N 467112-00 Rev. 2/06
APW WYOTT EQUIPMENT LIMITED WARRANTY
APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the
following conditions:
This warranty applies to the original owner only and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, at the option of
APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency. APW Wyott will only be
responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott
Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated
with same. The closest APW Wyott Authorized Service Agent must be used.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There
will be no labor coverage for equipment located on any island not connected by roadway to the mainland.
Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada
may vary. Contact the international APW Wyott distributor, dealer, or service agency for details.
Time Period
One year for parts and one year for labor, effective from the date of purchase by the original owner. The Authorized Service Agency
may, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the
original product warranty only.
Exceptions
*Gas/Electric Cookline: Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all
component parts, except switches and thermostats. (2 additional years on parts only. No labor on second or third year.)
*Broiler Briquettes, Rock Grates, Cooking Grates, Burner Shields, Fireboxes: 90 Day Material Only. No Labor.
*Heat Strips: Models FD, FDL, FDD, FDDL. Two (2) Year Warranty on element only. No labor second year.
*Glass Windows, Doors, Seals, Rubber Seals, Light Bulbs: 90 Day Material Only. No Labor.
In all cases, parts covered by extended warranty will be shipped FOB the factory after the first year.
Portable Carry In Products
Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment
weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to
the following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of
connection, or use, at APW Wyott's option or its Authorized Service Agency, it will be serviced on site or replaced.
From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott
Authorized Service Agency for in-warranty repairs. No mileage or travel charges are allowed on portable units after the first day of use.
If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)
countertop warmers and cookers, which are covered under the Enhanced Warranty Program, and (2) toasters or rollergrills which have
in store service.
Exclusions
The following conditions are not covered by warranty:
*Equipment failure relating to improper installation, improper utility connection or supply and problems due to
ventilation.
*Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning
and water damage to controls.
*Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect,
abuse, accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot or act of god.
*Equipment that has the model number or serial number removed or altered.
If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the
warranty period, then the manufacturer shall not be liable for any damages to any person or to any property, which may result from the
use of the equipment thereafter.
This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which
normally involve overtime or premium labor rates, the owner shall be charged for the difference between normal service rates and such
premium rates. APW Wyott does not assume any liability for extended delays in replacing or repairing any items beyond its control.
In all cases, the use of other than APW Wyott Authorized OEM Replacement Parts will void this warranty.
This equipment is intended for commercial use only. Warranty is void if equipment is installed in other than commercial application.
Water Quality Requirements
Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before
being used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.
Note: Product failure caused by liming or sediment buildup is not covered under warranty.
“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES
AND CONSTITUTES THE ENTIRE LIABILITY OF APW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY
EXTEND BEYOND THE TERMS STATED HEREIN.”
9/05
8