17W & 25W WALL PACK IN STALLATION
WARNING
1. To a v o id elec t r i c s h o c k , di s c o n n e c t p o w e r at source pri or to i nstal l ati on.
2. T he ins t a lla t ion s h o u l d be p e r fo r m e d by qual i fied el ectri ci ans or l i ghti ng techni ci ans.
3. B e f o r e c o nd uc t i n g an y i n s t al l at i o n , m ai n t enance, or rem oval , di sabl e al l power to the l um i nari e s a n d wa it
unt il t he fi x t ur e c o o l do w n .
4. Do no t t o uc h th e fixt u r e w h i l e i t i s i n s e r vi ce.
5. If t he r e is a ny p r o bl e m w i t h t h e fixt u r e, D O turn off power and DO NOT attem pt repai r unl ess you a re a
q ua lifi e d t ec hn i c i an o r t h e c u s t o m e r s e r v i ce m em ber.
6. T he elec t r ic a l r at i n g o f t h i s p r o du c t i s 1 2 0 - 2 7 7 V AC when no photocel l . There are 1 2 0 V and 2 77V vers ion
f o r t his p r o d uc t s w h e n c o n t ai n s p h o t o c e ll . Pl ease read the l abel i nf orm ati on caref ul l y to get proper in pu t
v o lt a g e f o r t hi s p r o du c t .
Mounting with a 1/2” conduit at the bottom
1. Removing the len by loosening the
two screws aside the len, removing the
reflector by loosening the two screws .
2. Remove the threaded plug from
the bottom, Plug the 1/2” conduit into
the fixture, konck out 2 screw holes on the
back housing and attach the fixture on
the wall with proper screws, use the
supplied gasket for a weather tight seal.
3. Connect Black for line, White for
Neutral and bare wire for Ground to
complete the wiring.
4. Replace the reflector and lens
carefully by reversing procedure
used to remove it.
2. Knock out the 2 screw holes and
the holes in the center of the back
housing, Plug the wires from the J-BOX
into the fixture through the center hole,
and attach the fixture to the J-box with
proper screws. use the supplied gasket
for a weather tight seal.
3. Connect Black for line, White for
Neutral and bare wire for Ground to
complete the wiring.
4. Replace the reflector and lens
carefully by reversing procedure
used to remove it.
Mounting with J-box
1. Removing the len by loosening the
two screws aside the len, removing the
reflector by loosening the two screws .
Catalog # ESL-1725WP-INSTALL-2017-V2
ESL Vision, LLC 2017
888.493.5559
info@eslvision.com
www.eslvision.com
3 0W, 45W, A N D 70W WALL PACK IN STALLATION
WARNING
1. To a v o id elec t r i c s h o c k , di s c o n n e c t p o w e r at source pri or to i nstal l ati on.
2. T he ins t a lla t ion s h o u l d be p e r fo r m e d by qual i fied el ectri ci ans or l i ghti ng techni ci ans.
3. B e f o r e c o nd uc t i n g an y i n s t al l at i o n , m ai n t enance, or rem oval , di sabl e al l power to the l um i nari e s a n d
w a it unt il t he fixt u r e c o o l do w n .
4. Do no t t o uc h th e fixt u r e w h i l e i t i s i n s e r vi ce.
5. If t he r e is a ny p r o bl e m w i t h t h e fixt u r e, D O turn off power and DO NOT attem pt repai r unl ess you a re a
q ua lifi e d t ec hn i c i an o r t h e c u s t o m e r s e r v i ce m em ber.
1. Junction box Mounting
1. Loosen screws and remove the front case set carefully from the back plate.
(Angle between front case and back plate varies from 0 degree to 45 degree.
Push up to take down the front case.)
2. Remove 1/2'' plug in center (B) for wiring, the fixture supports standard 3
1/4'' and 4''Junction box.
3. Attach the back plate on the wall, use the supplied gaskets for a weather
tight seal.
4. Finish wiring (Black for Line, White for Neutral and Yellow Green for Ground).
5. Replace the lens set on the hinges, make connections and close the lens set
then tighten the screws.
A - 1/2” NPS tapped holes
(surface conduit or photo control)
B - 1/2” Nps Tapped Holes
C - 5/16” dia. Screw hole
Front housing
Sealing ring
Bottom box
Leveling Bubble
EVA Gasket
2. Conduit Mounting
1. Loosen screws and remove the front case set carefully from the back plate.
(Angle between front case and back plate varies from 0 degree to 45 degree.
Push up to take down the front case.)
2. Remove 1/2” plug from where you intend to feed conduit .
3. Drilling out the holes (C) to secure it on the wall with choosing proper screws.
4. Finish wiring (Black for Line, White for Neutral and Yellow Green for Ground).
5. Replace the lens set on the hinges, make connections and close the lens set
then tighten the screws.
Screw
3. Photocell Installation (Optional)
RED
BLACK
BLACK
LAMPLOAD
1. Install photocell and wire as per diagram.
2. Use photocell rated for your supply voltage.
BLACK
WHITE
WHITE OR YELLOW
Troubleshooting
INPUT
1. Check that the line coltage at the fixture is correct. Refer
to wiring directions.
2. Is the fixture grounded properly?
2. Be sure the photocell, if used, is functioning properly.
888.493.5559
PHOTOCONTROL
WHITE
Universal voltage driver permits operation at 120V to 277VAC,
60 Hz except fixtures factory ordered with a 120V photocell
(P1) or 277V photocell (P2) or 120-277V photocell(P0) or
347V photocell (P3)
info@eslvision.com
Catalog # ESL-304570WP-INSTALL-2017-V2
ESL Vision, LLC 2017
www.eslvision.com
90 W & 135W WALL PACK IN STALLATION
WARNING
1. To a v o id elec t r i c s h o c k , di s c o n n e c t p o w e r at source pri or to i nstal l ati on.
2. T he ins t a lla t ion s h o u l d be p e r fo r m e d by qual i fied el ectri ci ans or l i ghti ng techni ci ans.
3. B e f o r e c o nd uc t i n g an y i n s t al l at i o n , m ai n t enance, or rem oval , di sabl e al l power to the l um i nari e s a n d
w a it unt il t he fixt u r e c o o l do w n .
4. Do no t t o uc h th e fixt u r e w h i l e i t i s i n s e r vi ce.
5. If t he r e is a ny p r o bl e m w i t h t h e fixt u r e, D O turn off power and DO NOT attem pt repai r unl ess you a re a
q ua lifi e d t ec hn i c i an o r t h e c u s t o m e r s e r v i ce m em ber.v
1. Junction box Mounting
1. Loosen screws and remove the front lens set carefully
from the back plate.
2. Drill appropriate knockouts (B) for wiring, the fixture
supports standard 3 1/4'' and 4''Junction box.
3. Attach the back plate on the wall, use the supplied gaskets for
a weather tight seal.
Top
Gasket
C
B
C
4. Finish wiring (Black for Line, White for Neutral
and Green/Yellow Green wire for Ground).
5. Replace the lens on the hinges, make connections and
close the lens set then tighten the screws.
Wire Connection
Black
Line
White
Neutral
Green/Yellow Green
Ground
888.493.5559
info@eslvision.com
www.eslvision.com
2. Conduit Mounting
1. Loosen screws and remove the front lens set carefully from the
back plate. (See step 1 above)
2. Remove 1/2” plug from where you intend to feed conduit .
3. Drilling out the holes (C) to secure it on the wall with
choosing proper screws.
4. Finish wiring ( Black for line, White for neutral and
Green/Yellow Green for ground). (See step 4 above)
5. Replace the lens set on the hinge and finish connection, Close
the lens set and tighten the screws to fasten the lens set to the
back plate.
C
C
C
Catalog # ESL-90135WP-INSTALL-2017-V2
ESL Vision, LLC 2017
888.493.5559
info@eslvision.com
www.eslvision.com