ST sup-plus GOR_13cop_19 390 3625 00_EN

Contents
1.
2.
3.
4.
Description of the controls ________________________________ 2
Operating instructions ___________________________________ 11
Cleaning and maintenance _______________________________ 24
Troubleshooting _______________________________________ 28
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use
of your dishwasher.
The individual sections are laid out to provide you with a step-by-step
guide to all your appliance's functions; the texts are easy to understand
and are complete with detailed illustrations.
Recommendations are given for the correct use of the baskets, spray
arms, containers, filters, washing programs, and for operating the
controls.
Following the cleaning instructions provided here will keep your
dishwasher's performance at peak levels in the long term.
This user-friendly manual will provide answers to all your questions
about use of the dishwasher.
USER INSTRUCTIONS: these consist of recommendations for using the
appliance, a description of its controls and of the correct cleaning and
maintenance procedures.
1
User instructions
1. Description of the controls
1.1
Upper panel
All the dishwasher controls are grouped on the upper panel. Switch-on,
programming, switch-off etc. procedures are only possible when the
door is open.
1
ON/OFF BUTTON
Pressing this button energises the appliance.
2
SELECTED PROGRAM INDICATOR LIGHTS
Illumination of this light denotes the program selected and the
occurrence of a fault (troubleshooting).
3
PROGRAM SELECTION BUTTON
By pressing this button in sequence it is possible to select the
desired program.
4
WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT
The light flashes to indicate that the appliance is in “water hardness
adjustment” mode.
SALT WARNIN LIGHT (on some models only)
If the
symbol is present, illumination of this light denotes a
regenerating salt warning level.
5
RINSE AID WARNING LIGHT (on some models only)
Illumination of this light signals that rinse aid dispenser is empty.
EXTRA PROGRAM + EXTRA OPTION BUTTON
6
(see “EXTRA OPTIONS” section)
The button controls selection of the extra programs. (see table).
7
2
EXTRA PROGRAM LIGHT
Illuminates to indicate that one of the extra programs (see table) is
going to be executed.
User instructions
ENERSAVE OPTION + EXTRA OPTION BUTTON
8
(see “EXTRA OPTIONS” section)
Press the button to enable/disable the option.
9
ENERSAVE OPTION LIGHT
Illuminates to indicate that the function is activated.
10
HALF LOAD BUTTON
Press this button to activate the half load wash option.
11
HALF LOAD LIGHT
Illuminates to indicate that the function is activated.
12
"3/1" OPTION (EXTRA OPTION) LIGHT
Illuminates to indicate that the function is activated.
13
PROGRAM DELAY BUTTON
Press this button to delay the start of the program.
14
INFORMATION DISPLAY (1 or 3 digits depending on model)
N.B.: symbols and styling are guideline and may vary depending on
the model or version of the dishwasher purchased.
Information displayed
no
no
1 - 9 hours
E
Scheduled program
duration
Remaining program
time
Delayed start
Error message
yes
yes
1 - 24 hours
Err
SETTING THE WASHING PROGRAM AND SWITCHING ON
To select the most suitable program for the dishes to be washed refer to
the table below, which indicates the most appropriate program according
to dish type and degree of soiling.
After using the table to identify the most appropriate washing program:
•
•
•
press the ON/OFF button (1) and wait for the PROGRAM
INDICATOR LIGHT (2) to illuminate;
keep pressing the PROGRAM SELECTION button (3) until the
indicator light corresponding to the desired program illuminates;
close the door; after about 2" the program will start. While it is in
progress, the relative LIGHT will flash (indicating that the program is
being executed).
3
User instructions
DURATION
PROGRAMME,
NUMBER &
SYMBOL
1 RINSE
2 DELICATE
3 AUTO
60-70
LOAD CROCKERY AND
CUTLERY
****
WATER
LITRES
POWER
KWh (1)
45 (3)
9
0,90
Delicate dishes with
normal dirt.
Cold prewash
Wash at 45°C
Cold rinse
Rinse at 70°C
Dry
75 (3)
16
1,15
EN 50242
5 HYGIENE PLUS
MINUTES
(1)
Cold rinse
Rinse at 70°C
Dry
Dishes with normal dirt,
even with dried-on
residues.
4 BIO (*)
CONSUMPTION
Pans and dishes for rinsing
and drying.
Pans and dishes with
normal dirt, even with driedon residues.
IEC/DIN
***
PROGRAM
PROGRESS
Very dirty pans and dishes,
even with dried-on
residues.
When the "AUTO" program is selected, the dishwasher
recognises the type of dirt and automatically adjusts the
washing parameters as appropriate.
Cold prewash (4)
Wash at 45°C
Cold rinse
Rinse at 55°C
Dry
Hot prewash
Wash at 70°C
Cold rinse (2)
Rinse at 70°C
Dry
**
**
**
150 (3)
15
1,50
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
The "HYGIENE PLUS" program terminates with an anti-bacteria rinse that ensures a
further reduction in the bacteria level. If the temperature falls during this stage of the
program (e.g. because the door is opened or due to a power blackout), the program
lights (3) flash to warn that the anti-bacteria effect is not guaranteed.
The washing cycle will not take place if the dishwasher door is left open
or not properly closed.
4
User instructions
EXTRA PROGRAMS
(see relevant section for explanation of functioning modes)
PROGRAMME
NUMBER E
SYMBOL
6 SOAK
+
7 QUICK
+
8 AUTO
40-50
DURATION
LOAD CROCKERY AND
CUTLERY
PROGRAM
PROGRESS
Pans and dishes awaiting
completion of the load.
Delicate dishes, with light
dirt, washed immediately
after use.
Dishes with normal dirt,
washed immediately after
use
CONSUMPTION
MINUTI
(1)
WATER
LITRES
POWER
KWh (1)
Cold prewash
15 (3)
5,5
0,02
Wash at 38°C
Cold rinse
Rinse at 58°C
45 (3)
13
0,85
When the "AUTO" program is selected, the dishwasher
recognises the type of dirt and automatically adjusts the
washing parameters as appropriate.
+
9 ECO
+
10 INTENSIVE
EXPRESS
+
Dishes with normal dirt,
washed immediately after
use.
Cold prewash
Wash at 55°C
Cold rinse
Rinse at 70°C
Dy
110 (3)
15
1,50
Mixed dishes with normal
dirt without dried-on
residues.
Wash at 65°C
Cold rinse
Rinse at 70°C
50 (3)
10
1,20
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
The washing cycle will not take place if the dishwasher door is left open
or not properly closed.
5
User instructions
NOTES AND REFERENCES
Only run the soak program with half loads.
Options cannot be used with the soak program.
The ENERSAVE option cannot be used with soak, hygiene plus, or any programs
which do not include the final drying stage.
Standard programme under EN 50242. If present, the ENERSAVE option must
*
be enabled.
**
See information sheet provided
*** IEC/DIN reference programme. If present, the ENERSAVE option must be
enabled.
**** Reference program for laboratories: Detergent: 20g in the dispenser + 10g in
the door or tablet. Configuration: see photo in “Using the baskets”.
(1) The cycle duration and power consumption may vary according to the water
and room temperatures, and the type and amount of dishes.
(2) 1 or 2 cold rinses depending on the model.
(3) For 3 digit models, see display.
(4) On some models only
REFERENCES for the ENERGY LABEL supplied with the dishwasher:
-
-
-
6
Annual energy consumption is based on 280 standard wash cycles with
cold water and consumption of low-energy operating modes. Actual
consumption depends on the way in which the appliance is used.
Water consumption is based on 280 standard wash cycles. Actual
consumption depends on the way in which the appliance is used.
Information refers to the EN 50242 STANDARD programme (identified in
the programmes table), which is the most effective in terms of combined
energy and water consumption. The programme is recommended for dishes
with a normal level of dirt.
Energy consumption in “sleep” mode = 0.02 W.
Energy consumption in “on” mode = 1.5 W.
Drying efficiency class on a scale from “G” (minimum efficiency) to “A”
(maximum efficiency).
User instructions
1.2
Washing programs
Before starting a washing program make sure that:
•
The water supply tap is open.
•
The correct amount of detergent has been added to the
dispenser.
•
The baskets have been correctly loaded.
•
The spray arms are able to rotate freely and without
obstruction.
•
The dishwasher door is securely closed.
EXTRA PROGRAMS
Button (6) gives access to five extra programs in addition to the ones
which can be selected directly using the program selector button.
This button must be pressed (the light comes on) after selection of the
“main” program (1,2,3,4 or 5).
This function is retained in the memory, so the button has to be pressed
again (the light goes out) if the user wishes to execute one of the 5 main
programs at the next cycle.
ENERSAVE OPTION
This option can be selected with the wash programme of choice to
further reduce energy consumption. Drying is aided by a special
device that automatically releases the door, which opens slowly and
smoothly by a few centimetres. This ensures perfect drying and greater
control of rinsing temperatures, which can be kept at lower levels for
significant energy saving.
Once the door has opened, the dishwasher
emits a short beep and programme lights
nos. 4 and 5 flash to indicate the end of the
washing cycle.
Enersave is activated automatically every time a wash cycle is
selected (except for programs that do not include the final drying phase;
see programs table) and can be disabled before the program is started.
When the function is activated, opening of the door must not be
impeded in any way; do not leave anything in the space in front of the
door necessary to allow it to open. Do not re-close the door during
automatic opening as this would damage the mechanism. Wait for the
pushers to retract before re-closing the door.
7
User instructions
SPREAD HALF LOAD
When there are not many dishes to be watched, the “spread half load”
option, controlled by button (10) is useful; it saves water and electricity
and reduces the program’s duration. Place dishes in both baskets then
load the detergent dispenser than less than the normal amount for a full
load..
EXTRA OPTIONS - “3/1” BUTTON
Press buttons 6 + 8 (EXTRA PROGRAMS button + ENERSAVE option
button) simultaneously to activate the "3/1" option; the respective light
(12) comes on to confirm the selection. The option is optimised for use of
detergents which are complete with salt and rinse aid, known on the
market as "3 in 1", "triple action", etc. With this option activated, any salt
and rinse aid If you wish to use detergents which already contain salt
and rinse aid already in the dishwasher will not be used.
N.B.: even with the "3/1" option selected, the regenerating salt/rinse aid
lights will still stay on if their containers are empty.
IMPORTANT: the option continues to be active until it is deactivated by
pressing buttons 6 + 8 simultaneously; the light (12) will then go out.
3/1 products are not suitable for use with excessively hard water.
Therefore, if the water hardness is set higher than H3, the 3/1 OPTION
light (12) flashes to indicate a setting error. This does not prevent the
use of the option, but the washing results might not be of the best.
DELAYED START
The start of the washing program can be delayed to program the
dishwasher to operate at the preferred time of day (e.g. overnight). Press
the PROGRAM DELAY button (13) to activate the option and display (14)
a 1 hour delay. Keep pressing to select the delay required, which may be
up to 9, 12 or 24 hours depending on the model.
When the door is closed, the appliance will prewash the dishes, after
which the "program delay" set will come into effect.
8
User instructions
CANCELLING THE CURRENT PROGRAM
•
To cancel the currently selected program, open the door and hold
down the PROGRAM SELECTION (3) button for a few seconds
until the indicator lights for programs 4 and 5 illuminate
simultaneously (the word "end" is displayed on the window).
•
•
Close the door.
After approximately 1 minute the dishwasher will advance to the end
of cycle.
CHANGING THE PROGRAM
To change the program in progress, simply open the door and select a
new program. When the door is closed the dishwasher will automatically
select the new program.
TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT
•
•
•
Always try to run the dishwasher fully loaded.
Do not wash the dishes in running water.
Use the washing program that is most appropriate for each type of
load.
•
Do not carry out any preliminary rinsing.
•
If available, connect the dishwasher to a hot water supply up to 60°C.
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT
THE ENVIRONMENT
The phosphates contained in dishwasher detergents are harmful to the
environment. To avoid using excessive amounts of detergent and to save
on electricity, observe the following:
•
•
separate the more delicate items from dishes that are more resistant
to aggressive detergents and high temperatures;
do not pour the detergent directly on the dishes.
If the door has to be opened while washing is in progress, the program
will be interrupted. The relative light will keep flashing and a beeper will
signal that the cycle has not been completed. You must wait about 1
minute before closing the door to restart the program. When the door is
closed the program will continue from where it was interrupted. This
operation should only be carried out if strictly necessary, because it
might cause problems in execution of the program.
9
User instructions
END OF CYCLE
At the end of the washing cycle the dishwasher
gives a short acustic signal and the program
indicators nr 4 and 5 start blinking (the word
"end" is displayed on the window).
To switch off the dishwasher, open the door and press the ON/OFF
button (1).
ENERGY MANAGEMENT
After 5 minutes of waiting (washing cycle completed, stopped or set but
not started) the dishwasher switches to a standby state to reduce
energy consumption.
In this state, the dishwasher indicator panel (lights or display depending
on model) functions more slowly (switch-on once every 5 seconds).
REMOVING THE DISHES
At the end of the washing program, wait at least 20 minutes before
removing the dishes, to allow them to cool down. To prevent any water
droplets on the upper basket from falling on the dishes in the lower
basket, it is advisable to unload the lower basket first, and then the
upper basket.
10
User instructions
2. Operating instructions
Once the dishwasher has been correctly installed, prepare for use as
follows:
•
•
•
2.1
Adjust the water softening system;
Add the regenerating salt;
Add the rinse aid and detergent.
Using the water softening system
The amount of scale contained in the
water (water hardness index) can cause
whitish staining on the dry dishes, which
tend to become dull over time. The
dishwasher is equipped with an automatic
softening system which uses a special
regenerating salt to reduce the hardness
of the water.
The dishwasher is factory set for water
hardness level 3 (average hardness
41-60°dF – 24-31°dH ).
SALT
When using water of medium hardness, the regenerating salt container
should be refilled after approximately 20 washing cycles. The salt
container can hold approximately 1.7 Kg of salt in grains. The container
is situated at the bottom of the dishwasher. After removing the lower
basket, unscrew the salt container cap by turning it anticlockwise and
pour in the salt using the funnel supplied with the dishwasher. Before
replacing the cap, remove any salt residues from around the opening.
•
When using the dishwasher for the first time, in addition to the salt it
is also necessary to add one litre of water to the container.
•
Each time the salt container is refilled, make sure that the cap is
securely closed. The mixture of water and detergent must never
penetrate the salt container, as this would compromise the operation
of the regeneration system. In the event of this occurring, the
warranty will be invalidated.
•
Only use regenerating salt specially formulated for domestic
dishwashers. If using salt tablets, do not fill the container
completely.
11
User instructions
•
Do not use table salt as it contains insoluble substances which,
over time, may damage the water softening system.
•
When necessary, refill the regenerating salt container before
starting the washing program. In this way, the excess saline
solution will be immediately removed by the water; the prolonged
presence of salt water inside the tank may lead to corrosion.
Be careful not to confuse the salt and detergent packages; adding
detergent to the salt container will damage the water softening system.
ADJUSTING THE WATER SOFTENING SYSTEM
The dishwasher is equipped with a device which allows the softener
setting to be varied to suit the hardness of the mains water. The
hardness is set using the PROGRAM SELECTION BUTTON (3).
To access the setting function, hold the button down for more than 15
seconds. The WATER HARDNESS ADJUSTMENT INDICATOR LIGHT
(4) flashes, while the SELECTED PROGRAM INDICATOR LIGHTS (2)
show the current setting. Each pressure on the button changes the
setting following the sequence in the table below:
>
12
User instructions
WATER HARDNESS TABLE
WATER HARDNESS
German
French
degrees (°dH)
Degrees (°dF)
0-4
0-7
5 - 15
8 - 25
16 - 23
26 - 40
24 - 31
41 - 60
32 - 47
61 - 80
48 - 58
81 - 100
SETTING
All lights off
(no salt)
One light on
Two lights on
Three lights on
Four lights on
Five lights on
Contact your local water board for information on the hardness of your
water supply.
After adjustment or display of the current setting, simply do not touch the
button for a few seconds; the dishwasher will automatically return to
standard mode, quitting the adjustment mode.
2.2
Using the rinse aid and detergent dispensers
The detergent and rinse aid
dispensers are situated on the inner
part of the door: the detergent
dispenser is on the left, and the
rinse aid dispenser is on the right.
With the exception of the SOAK program, before every washing cycle it
is necessary to add the required amount of detergent to the detergent
dispenser. The rinse aid, on the other hand, should only be added as
required.
13
User instructions
ADDING THE RINSE AID
The rinse aid helps the dishes dry faster and
prevents the formation of scale deposits and
staining; it is automatically added to the water
during the final rinse cycle, from the container
situated on the inner side of the door.
To add rinse aid:
•
Open the door.
•
Rotate the container cap anticlockwise by ¼ of a turn and remove it.
•
Add the rinse aid until the container is full (approximately 140 cc).
The optical level indicator on the side of the cap should be
completely obscured. Refill the rinse aid when the optical level
indicator becomes clear again, or when the rinse aid warning light
illuminates.
•
Replace the cover and turn it in a clockwise direction.
•
Use a cloth to remove any spillage of rinse aid which might lead to
the formation of excess foam.
ADJUSTING THE RINSE AID DISPENSER SETTING
The dishwasher is factory set for medium water hardness. However it
possible to change the setting by turning the dispenser’s selector to the
desired position: the amount of rinse aid dispensed is proportional to the
selector position.
•
•
•
•
•
14
To adjust the rinse aid setting, rotate the dispenser cap through a
quarter turn in an anticlockwise direction and remove it.
Then use a screwdriver to rotate the rinse aid selector to the desired
position.
Replace the cap, turning it clockwise.
The amount of rinse aid must be increased if the washed dishes
appear dull or feature circular stains.
If, on the other hand, the dishes are sticky or have white streaks, it
is necessary to reduce the rinse aid setting.
User instructions
ADDING THE DETERGENT
To open the detergent dispenser cap, lightly press
the button P. Add the detergent and close the cap
carefully.
During the washing cycle, the dispenser will be
opened automatically.
•
•
•
•
•
•
When a program with hot prewash is selected (see program table),
extra detergent must be placed in the cavity G/H (depending on
models).
Use only detergents specially formulated for dishwashers. For optimal
washing results it is important to use a good quality detergent.
The detergent packs must be sealed and stored in a dry place to
prevent the formation of lumps which may negatively affect washing
results. Once opened the detergent packs should not be kept for too
long, otherwise the detergent loses its effectiveness.
Do not use detergents formulated for washing dishes by hand,
because they produce a great deal of foam and may negatively affect
the operation of the dishwasher.
Add the correct amount of detergent. An insufficient amount of
detergent will result in a partial removal of dirt from the dishes,
whereas an excessive amount is wasteful and does not improve the
washing results.
The market offers liquid and powder detergents with differing chemical
compositions, which may contain phosphates, or be phosphate-free
but contain natural enzymes.
- Detergents containing phosphates are more effective against
grease and starch at temperatures above 60°C .
- Enzyme detergents, on the other hand, are also effective at lower
temperatures (from 40 to 55°C ) and are more easily
biodegradable. With enzyme detergents it is possible to obtain at
low temperatures comparable results to those which can only be
achieved at 65°C using traditional detergents.
For the safeguarding of the environment we recommend the use of
phosphate- and chlorine free detergents.
15
User instructions
The introduction of detergent into the rinse aid dispenser, even in
liquid form, will damage the dishwasher.
2.3
General warnings and recommendations
Before using the dishwasher for the first time, it is advisable to read the
following recommendations concerning dish types to be washed and
their loading.
There are generally no constraints on the washing of domestic dishes,
but in certain cases it is necessary to take their characteristics into
account.
Before loading the dishes into the baskets it is necessary to:
•
remove coarse food remains: e.g. bones, fish-bones, etc. which
may clog the filter or damage the wash pump.
•
soak any pots or pans with burnt-on food remains on the bottom to
facilitate removal, then load them into the LOWER BASKET.
There is no need to pre-wash the dishes under running water before
loading them into the baskets since this only wastes water.
Correct loading of the dishes helps ensure optimal washing
results.
16
User instructions
WARNING!
•
•
•
•
•
Make sure that the dishes are securely in place so that they cannot
tip over or obstruct the rotation of the spray arms during the
washing cycle.
Do not place very small objects in the baskets as these could fall
and obstruct the spray arms or the wash pump.
Containers such as cups, bowls, glasses and pots should always
be loaded with the opening facing downwards and with any cavities
at an angle, to allow the water to drain out.
Do not stack dishes or place them in such a way that they cover
one other.
Do not place glasses too close together because they may knock
against each other and break, or there might be staining at the
point where they touch.
MAKE SURE that the items being washed are dishwasher-safe.
Items which are not dishwasher-safe:
•
•
•
•
•
•
•
•
Wooden dishes, pots or pans: these may be damaged by the
high washing temperatures.
Handcrafted items: these are rarely suitable for washing in a
dishwasher. The relatively high water temperatures and the
detergents used may damage them.
Plastic dishes: heat resistant plastic dishes must be washed in the
upper basket.
Dishes and objects in copper, tin, zinc or brass: these tend to
stain.
Aluminium dishes: items made from anodised aluminium may
lose their colour.
Silverware: silver items may stain.
Glass and crystal: in general, glass and crystal objects can be
washed in the dishwasher. However, certain types of glass and
crystal may become dull and lose their clearness after many
washings. Therefore, for these items we recommend using the
least aggressive program available.
Decorated items: the decorated objects available on the market
are generally able to withstand washing in the dishwasher,
although the colours may fade after a great many washes. If in
doubt as to the fastness of the colours, it is advisable to wash just a
few items at a time for approximately one month.
17
User instructions
2.4
Using the baskets
The dishwasher has a capacity of 13 place-settings, including serving
dishes.
LOWER BASKET
The lower basket receives the full force of the lower spray arm, and
should therefore be used for the “toughest” items with a heavier degree
of soiling.
All types and combinations of loads are
permitted, provided that the dishes, pots and
pans are arranged with all the soiled surfaces
exposed to the water jets coming from the
bottom.
With fixed supports
To make the most of the space inside the
basket when loading large items, certain
models are equipped with tip-up supports for
plates in 2 or 4 sections.
With tip-up supports
BOTTOM BASKET INSERTS
Some models are equipped with bottom basket inserts which improve
the drying of dishes. The inserts are supplied in the accessories bag; to
use them, simply fit them into place as shown.
18
User instructions
LOADING THE LOWER BASKET
Carefully load flat plates, soup plates, dessert and serving dishes,
positioning them vertically. Pots, pans and their covers must be loaded
upside down. When loading soup plates and dessert bowls, be sure to
leave a gap between them.
Loading examples:
Examples of loading for intensive dirt:
19
User instructions
CUTLERY BASKET
The basket has removable top grids into which items of cutlery should
be inserted to keep them properly spaced and allow water to pass
between them effectively. The top grids and central lid are in the bag of
accessories. The central lid functions as a lid only.
The top grids can be detached and used separately.
The cutlery should be arranged in an orderly manner inside the basket,
with the handles pointing downwards. Take care during loading to avoid
injury from the knife blades. The basket is suitable for all types of cutlery,
except those long enough to interfere with the upper spray arm. Ladles,
wooden spoons and cooking knives can be placed in the upper basket,
making sure that the knife blades do not protrude from the basket.
The cutlery basket slides across the dishwasher and can be placed in
any position to allow optimal use of the space in the bottom basket.
20
User instructions
UPPER BASKET
It is recommended to load the upper basket with small- or medium-sized
items such as glasses, small plates, tea or coffee cups, shallow bowls
and light objects made from heat resistant plastic. If the upper basket is
used in the lowermost position, it can also be loaded with serving dishes,
provided they are only slightly soiled.
LOADING THE UPPER BASKET
Load plates facing forward; cups, bowls etc. must always be facing
downwards. The left side of the basket can be loaded with cups and
glasses on two levels. In the centre section, plates and saucers can be
loaded vertically into the supports provided.
Loading examples:
21
User instructions
Depending on the models, the basket may be equipped with some or all
of the following accessories:
Supports for cups or long objects (ladles, spoons…), on the left;
can be tipped to the vertical position when not in use.
Long-stemmed glass holder, on the left; to use, simply lift and
fix onto the hooks provided.
Cutlery racks, on the right, designed for knives and teaspoons;
for teaspoons, pull out the sliding support. The racks can be
tipped to the vertical position when not in use.
Fixed or movable racks in the middle. The movable supports
can be fixed vertical, resting on the bottom of the basket when
not in use, or set in the intermediate position, as required.
22
User instructions
ADJUSTING THE UPPER BASKET
The height of the top basket can be adjusted to allow large dishes or
pans to be placed in the bottom basket.
The adjustment procedure may be type A or B, depending on the
dishwasher model purchased.
Version A: pull-out with adjustment in two positions.
•
Pull out both the basket guides.
•
Remove the stops, first releasing them as shown in the diagram.
•
Pull out the basket.
•
Fit the upper or lower pair of wheels into the guide, depending on
the setting required;
•
Return the stops to their original position.
The left hand and right hand sides of the basket must always be set at
the same height.
Version B: with adjustment in three positions on both sides.
The sides of the basket must always be set at the same height.
•
Raise the basket by pulling on the top edge (1), to the first or second
catch depending on the height required.
•
To lower the basket, first release it by pulling the release lever (2).
Adjustment is also possible with the basket loaded, but in this case when
lowering the basket it should be held steady with one hand to avoid
knocking the dishes.
23
User instructions
3. Cleaning and maintenance
Before carrying out any work, always unplug the appliance from the
electrical supply or switch off the all-pole disconnection device.
3.1
General warnings and recommendations
Avoid the use of acidic or abrasive detergents.
Clean the outer surfaces and door-lining of the dishwasher regularly
using a soft cloth moistened with water or with a normal detergent
suitable for painted surfaces. Clean the door gaskets with a damp
sponge. Periodically (once or twice a year) it is advisable to clean the
tank and gaskets, using a soft cloth and water to remove any deposits.
CLEANING THE WATER INTAKE FILTER
The water intake filter A located at the outlet of the water supply tap
needs to be cleaned periodically.
After having closed the water supply tap, unscrew the end of the water
intake hose, remove the filter A and clean it delicately under running
water. Reassemble filter A in its seat and carefully screw the water
intake hose back into position.
CLEANING THE SPRAY ARMS
The spray arms can be easily removed for periodic cleaning of the
nozzles, to prevent possible clogging. Wash them under running water
and carefully replace them in their seats, checking that their rotary
movement is in no way impeded.
•
•
•
To remove the upper spray arm, unscrew locking ring R.
To remove the lower spray arm, simply lift it up, pulling by the
central part.
To remove the orbital spray arm assembly, take hold of the longer
arm and pull the orbital unit upward. Wash the arms under a jet of
running water and return them carefully to their seat. After
reassembly, check that the spray arms turn freely. Otherwise,
check that they have been installed correctly.
ORBITAL
24
User instructions
CLEANING THE FILTER UNIT
•
•
•
•
It is advisable to periodically inspect the centre filter C and, if
necessary, to clean it. To remove the filter, grip the tabs, turn them
anticlockwise and lift upwards;
push the centre filter D from the underside to remove it from the
micro-filter:
separate the two parts which make up the plastic filter by pressing
the body of the filter in the zone shown by the arrows;
remove the centre filter by lifting it upwards.
GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT
MAINTENANCE:
•
The filters should be cleaned under running water using a stiff
brush.
•
When removing the filter, take care that there are no food residues
on it. If any residues fall into the washing pit they might block
hydraulic components, or foul the spray arm nozzles.
•
It is essential to thoroughly clean the filters according to the
above instructions: the dishwasher cannot function if the filters are
clogged.
•
Carefully replace the filters in their seats, to avoid damaging the
wash pump.
PROLONGED DISUSE:
•
Run the soak program twice in succession.
•
Unplug the power cord from the socket.
•
Leave the door slightly open, in order to prevent the formation of
unpleasant odours inside the washing tank.
•
Fill the rinse aid dispenser.
•
Shut off the water supply tap.
25
User instructions
BEFORE STARTING THE DISHWASHER AFTER PROLONGED
DISUSE:
•
•
•
Check that there are no deposits of sludge or rust inside the water
pipe: if there are, allow the water to run from the water supply tap for
a few minutes.
Plug the power cord back into the socket.
Reconnect the water intake hose and open the tap again.
TROUBLESHOOTING MINOR PROBLEMS
In some cases it is possible to remedy minor problems by referring to the
following instructions:
If the program fails to start, check that:
•
•
•
•
the dishwasher is connected to the electrical power supply;
there is no power failure;
the water tap is open;
the dishwasher door is properly closed.
If water remains inside the dishwasher, check that:
•
•
•
the drain hose is not kinked;
the drain siphon is not obstructed;
the dishwasher filters are not clogged.
If the dishes are not being cleaned properly, check that:
•
•
•
•
•
•
•
26
the correct amount of detergent has been added;
there is regenerating salt inside the special container;
the dishes are being loaded correctly;
the selected program is suitable for the dish types and their degree
of soiling;
all the filters are clean and positioned correctly;
the spray arm nozzles are not obstructed;
there is no object obstructing the rotation of the spray arms.
User instructions
If the dishes fail to dry or remain dull, check that:
•
•
•
there is rinse aid inside the special container;
the rinse aid dispenser setting is correct;
the detergent used is of good quality and has not lost its
effectiveness (for example, through incorrect storage, with the box
left open).
If the dishes show signs of streaking, staining, etc., check that:
•
the rinse aid dispenser setting is not too high.
If there are visible traces of rust inside the tank:
•
•
•
the tank is made of steel, and therefore any rust marks are due to
external elements (fragments of rust from the water pipes, pots,
cutlery, etc.). Special products are commercially available to remove
such marks;
check that the amount of detergent being used is correct. Certain
detergents can be more corrosive than others.
check that the cap of the salt container is securely closed, and that
the water softening setting is correct.
If after following the above troubleshooting instructions the problem
persists, call the nearest After-Sales Centre.
WARNING: any operations performed on the appliance by
unauthorised persons are not covered by the warranty and shall be
paid for by the user.
27
User instructions
4. Troubleshooting
The dishwasher is able to indicate a series of malfunctions by
illuminating a number of lights simultaneously (see key below); “E” or
“Err” (depending on the model) also appears on the display in the event
of a malfunction.
FAULT
DESCRIPTION
E1
Acquastop failure
The anti-flooding system has been activated (for the
relevant models only). The system is tripped in case
of water leaks. Contact the after-sales service.
E2
Safety level
The system which limits the water level inside the
dishwasher has been tripped. Interrupt the program
and switch off the dishwasher. Switch the dishwasher
back on, program it again and start the washing
cycle. If the problem persists, contact the after-sales
service.
E3
Water heating malfunction
The water is not heated or the heating parameters
are not correct. Repeat the washing program; if the
problem persists, contact the after-sales service.
E4
Water temperature monitoring malfunction
Interrupt the program and switch off the dishwasher.
Switch the dishwasher back on, program it again and
start the washing cycle. If the problem persists,
contact the after-sales service.
E5
Water intake malfunction
The appliance does not take in water or does not do
so correctly. Check that the water connections are
correct, the water intake tap is turned on and the filter
is not fouled. If the problem persists, contact the
after-sales service.
E6
Water pump-out malfunction
The appliance does not pump out the water or does
not do so correctly. Check that the drain hose is not
kinked or crushed and that the siphon and filter are
not fouled. If the problem persists, contact the aftersales service.
28
User instructions
FAULT
DESCRIPTION
Turbine flow-regulator malfunction
(for the relevant models only)
The appliance is not able to "measure" the amount
of water loaded accurately. Interrupt the program
and switch off the dishwasher. Switch the
dishwasher back on, program it again and start
the washing cycle. If the problem persists, contact
the after-sales service.
E7
E8
Alternate washing system malfunction
Interrupt the program and switch off the dishwasher.
Switch the dishwasher back on, program it again and
start the washing cycle. If the problem persists,
contact the after-sales service.
E9
Water intake system malfunction
Contact the after-sales service.
Light off
Light on
Light flashing
If an alarm occurs the appliance interrupts the program in progress and
signals a fault.
•
Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program
immediately.
•
The E5, E6 alarms interrupts the running program once the cause is
resolved, it will bring bach the execution of the program.
•
The alarm E7 is visualized at the end of the cycle that comes, however,
brought to the end since the operation of the dishwasher is not harmed.
To “reset” an alarm is necessary:
•
Open and close the door, or turn off and on the machine. At this point is
possible to program the dishwasher again.
If the malfunction persists, contact your authorised Service Centre.
29
User instructions
TECHNICAL DATA
Width
Depth measured flush with the
outer edge of the control panel
Height (depending on models)
Capacity
Water supply pressure
Electrical characteristics
30
597 ÷ 599 mm
550 mm
from 820 mm to 870 mm
from 860 mm to 910 mm
13 Standard place settings
min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar)
See rating plate