FW422 Integrated In Column Larder Fridge

FW422 Integrated In Column
Larder Fridge
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
Important
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note that
CDA reserve the right to invalidate the guarantee supplied with this
product following incorrect installation or misuse of the appliance.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity:
This appliance has been designed, constructed and marketed in
compliance with safety requirements of EEC Directive 2006/95/EEC
(Low voltage) and requirements of EMC Directive 2004/108/EEC.
2
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation, including Electrical safety (LVD)
and Electromagnetic interference compatibility (EMC). Parts intended
to come into contact with food conform to EEC/89/109.4
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority differentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving from
inappropriate disposal and enables the constituent materials to be
recovered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
3
Important
Never store inflammable or explosive items and strong corrosive
acids or alkalis in the appliance.
This is a household appliance, which is produced in accordance with
the national standard. It is intended for food storage only, not for
storage of blood, medicine and biological products.
To prevent risk of fire, keep the appliance away from petrol or any
other inflammables.
To prevent risk of electromagnetic interference or other accidents,
do not place a microwave oven on top of the refrigerator or use any
electric appliance inside the refrigerator.
Do not allow children to play with or near the appliance.
The internal surface of freezer compartment is very cold when the
appliance is running. Do not touch the surface especially with wet
hands.
Do not splash water onto the appliance. Keep it away from places of
high humidity that may have adverse effect on the electric insulation
performance.
Please remove the door, door seal and shelves before disposal of the
old appliance and put them away in a safe place to prevent children
from being entrapped.
4
Before First Use
You must allow the fridge to settle for at least twenty four hours
prior to switching the power on.
It is recommended that you clean the interior of the appliance prior to
first use, using a solution of bicarbonate of soda and warm water and
then thoroughly drying the interior.
The fridge may have an odour to it at first use. This will disappear as
the appliance cools.
Please note:
The appliance will work continuously until it comes down to the
correct temperature.
If the appliance is switched off, you should allow five minutes
before switching it on again to prevent unnecessary damage to the
compressor.
This fridge cools your food by making the inside back of the cavity
cold. It is normal for frost to build up on this surface; it then dissipates
and drains through a small drain at the bottom, where it evaporates
harmlessly. The presence of frosting at the back is not a malfunction
of the fridge.
5
Setting the Temperature
You must allow the fridge to settle for at least twenty four hours
prior to switching the power on.
To adjust the temperature turn the thermostat control knob clockwise
(from off) to the required level. The temperature becomes colder the
higher the number on the control.
When the thermostat is set to 0 (off) the fridge light will continue to
work but the cooling system is switched off.
We recommend initially setting the temperature control in mid range
for the first 24 hours then adjusting the temperature up or down from
this point as your personal preference.
Use
Fridge
• Never put liquids in the refrigerator uncovered.
• Never put hot foods in the refrigerator. Warm food should be
allowed to cool to room temperature before being put into the
refrigerator.
• Nothing should rest against the rear wall of the refrigerator, as this
will cause frost and possible condensation problems which will be
difficult to remove.
• Make sure food is clean and any extra water is wiped away before
putting into the fridge.
• Wrap or cover food before putting into the fridge. This will help
prevent the loss of moisture, keep food fresh and avoid unpleasant
odours.
6
• Sort foods prior to storing. Any foods to be used soon should be
stored at the front of the shelf to prevent deterioration caused by
the door being open for prolonged periods.
• Do not overfill the fridge. There should be sufficient space between
the foods to allow the cool air to circulate.
• Thawing frozen foods in the fridge compartment will help to keep
the temperature low and save energy.
• Only open the door for as long as is necessary. Leaving the
door open for long periods will affect the temperature inside the
appliance and waste energy.
• Ensure all compartments are fully closed after use.
Care and Cleaning
Always disconnect the appliance from the power supply before
any cleaning or maintenance.
The fridge sections should be cleaned using a solution of bicarbonate
of soda and lukewarm water. Do not use abrasive products or
detergents. After washing, rinse and dry thoroughly.
Clean the shelves and balconies separately by hand with soap and
water. Do not put them in the dishwasher.
The water drain hole at the back of the fridge compartment and
the evaporating tray should be clened periodically to prevent the
defrosted water from collecting inside the fridge compartment. The
drain plug can be used to clean the drain hole.
7
Once cleaning is complete, then reconnect the power.
• Keep the door gasket clean. If damaged, the gasket should be
replaced.
• If the appliance is not used for prolonged periods of time, unplug
and clean the appliance. The door should be left slightly open to
prevent the formation of mildew and smell.
Defrosting the Fridge
The fridge is self-defrosting. Any water created will run out of the
fridge through the channel at the back of the fridge.
Itfig.is1 important to keep the channel clear at all times. The defrosted
water is collected in the evaporating tray at the back of the appliance.
8
Changing the Light Bulb
Disconnect the appliance from the power.
• Carefully remove the light cover by pushing in the lever at the back
of the cover, and then pulling the cover down.
• Unscrew the light bulb to remove it and replace with a new bulb (not
more than 15W).
• Replace the light cover and reconnect the power after five minutes’
delay as explained on page 3.
Troubleshooting
If you have any problems with your appliance, you should check
the troubleshooting prior to calling CDA Customer Care to prevent
unnecessary service calls and potential cost.
If the appliance is not working
• Check there is power to the appliance:
• The house fuses are intact and the fuse in the plug has not blown.
• The thermostat is not set to 0 (off position).
•The plug socket is functioning fine. To check this, plug another
electrical appliance in to see if the socket is working.
• The temperature of the room is adequate (10°C or above).
The appliance is working, but not very well
• The appliance is not overloaded.
• The thermostat is set to an appropriate temperature.
• The door is closing properly.
• The cooling system at the rear of the appliance is clean and free of
9
dust, and not touching the rear wall.
• There is enough ventilation at the side and rear walls.
• The temperature of the room is adequate (10°C or above).
The appliance is noisy
• The appliance is level and stable.
• The side and rear walls are clear, and there is nothing resting on the
appliance.
• The cooling gas in the refrigerator will make a slight bubbling noise,
even when the compressor is not running.
There is water in the lower part of the refrigerator compartment
• The drain hole in the channel at the back of the compartment is
clear.
10
Installation
Product Dimensions and aperture
required for installation:
Your refrigerator is designed to be
installed into a standard larder unit
of width 560-570mm and depth of
550mm. the diagram below shows
the product dimensions and aperture
required.
Note also the arrows on the diagram
show ventilation requirements. In the
diagram a plinth vent is fitted to allow
free air into the cabinet. This is not
necessary where there is already a free
air supply into the run of units provided
by a vent in another unit (or side of the
run).
90
¡
fig. 2
11
Fig. 3 - Fitting the decor door bracket
Unscrew and remove the nuts and
washers from the appliance door. Place
fixing bracket on the appliance door by
inserting the holes to adjustment bolts.
Dimension B= Measure from the
underside surface of kitchen unit to the
bottom of fixing bracket.
Dimension C= Measure from the
underside surface of kitchen unit to the
top of next unit door.
Fig. 4 - Fitting the decor door bracket
Substract C from B and put the
fixing bracket (2) in place using this
measurement for vertical position
and place to the centre for horizontal
position. Secure the fixing bracket (2)
using screws(1).
C
B
fig. 3
1
B-C
2
fig. 4
Fig. 5 - Fitting the decor door
Place the decor door onto the
appliance door by inserting adjustment
bolts into the slots on the fixing bracket.
Locate the washers and screw the nuts
onto the adjustment bolts.
fig. 5
12
Fig. 6 - Aligning the decor door
Close the door and check the
alignment with the other unit doors.
Adjust the decor door by screwing or
unscrewing the adjustment bolts for
vertical adjustment and by the help of
the slots on the fixing bracket for other
directions. Lock the screws into place
as shown in 4.
Fig. 7 - Fitting the decor door base
fixings
With the appliance door open, remove
the screws at the bottom of the
appliance door. Locate the decor door
base fixings (3) and screw the fixings to
the appliance door and the decor door.
10
10
8
fig. 6
1
3
fig. 7
Fig. 8 - Fitting the decorative cover
Fit the decorative cover (4) on the decor
door fixing bracket.
4
fig. 8
13
Fig.9 - Fitting the plinth
Fit the plinth section, providing
minimum 25 mm gap between the
cabinet door and fix it.
Never cover over the ventilation slots.
Once installed the plinth must not
block the ventilation slots in the
appliance.
This may require cutting the plinth
down. Failure to ensure adequate
ventilation may invalidate the
warranty.
14
min 25mm
fig. 9
Reversing the Door
It is possible to reverse the door on
this appliance, if required. To do so,
follow the steps below:
1.Open the door.
2. Remove the white hinge screw cover
plate carefully to gain access to the
hinge screws.
3. Loosen the hinge fixing screws (1)
and remove the door.
4. Remove the door fixing screws (2).
5. Remove the cover caps (3).
6.Relocate the hinges as shown.
7. Refit the door to the hinges.
Do not turn the door upside down
8.Insert the cover caps (3) on the
opposite side in the exposed holes.
9. Refit the hinge screw cover plate.
fig. 10
15
Electrical Information
Warning! This appliance must be earthed.
The mains lead of this appliance has been fitted with a BS 1363A 13
amp fused plug. To change a fuse in this type of plug, follow the steps
below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the
fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in
position.
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should be
cut off and disposed of safely to prevent the risk of electric shock. A
suitable alternative plug of at least 13 Amp rating to BS 1363 should be
used.
16
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
• The wire which is coloured GREEN and YELLOW must be connected
to the terminal which is marked with letter (E) or by the Earth symbol
or coloured GREEN and YELLOW.
• The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter (N), or coloured BLACK.
• The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter (L) or coloured RED.
If in doubt regarding the electrical connection of this appliance,
consult a qualified electrician. Do not shorten the supply cable, the
appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible
place.
If the power supply cord is damaged, it must replaced by a CDA
authorised agent.
17
NOTES
18
NOTES
19
Please contact our Customer Care Department, or for Service on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Download PDF

advertising