SI-10
OWNER'S MANUAL
SI-10
DFP6
H38-30
TANK 10
HBSS1238
PSG12
AP25
BA25
DPN-10
DPG-10
DP-10
PW124-120
HBEL1238
ST2520
HBSS1238
H38B
PVCV34FM
W10
SSAXLE12
SHW3
AXC12
HB1438
STR14
SI-10
P56
R25
P14
AG100
HBBEL1814
AFR25
ABR25
HB14P
HB5638
SC1212
PL10-B
HBSSEL1238
HBSSEL1238
INSIDE VIEW - CONTROL PANEL
07-14-08
SI-10
PARTS LIST
PART NO.
DESCRIPTION
ABR25
AIR BOWL FOR R25
AFR25
AIR FILTER FOR R25
AG100
1.5in DRY MODEL 20 DUAL SCALE GAUGE
AP25
PLUG 1/4 NPTM AIR FITTING - BRASS
AXC12
1/2in PUSH NUT FOR AXLE CAP
BA25
MALE/FEMALE ADAPTER 1/4 X 1/4
DFP6
6 INCH THREADED CAP FOR 10 GALLON UNIT
DP-10
BULKHEAD BODY 1/2 FPT
DPG-10
DPN-10
BULKHEAD GASKET
H38-30
30FT OF 3/8in BLUE HOSE REPLACEMENT
HB14P
1/4in BRASS HB AIR FITTING
HB5638
HOSE BARB FOR P56 PUMP
HB1438
1/4in MPT X 3/8in HOSE BARB (PLASTIC)
HBBEL1438
3/8 BRASS HOSE BARB X 1/4 PIPE ELB
HBBEL1814
HOSE BARB ELBOW 1/8 x 1/4
HBEL1238
HOSE BARB ELBOW 1/2 X 3/8
HBSS1238
STAINLESS HOSE BARB 1/2 X 3/8
HBSSEL1238
304 S.S. 1/2in MPT BY 3/8in H.B. ELBOW
P14
COUNTERSUNK PLUG-HEXAGON 1/4
P56
5700 SANTO PUMP
PL10-B
PLASTIC PLATE FOR FI-10 UNIT
PSG12
1/2in POLY SPRAY GUN W/ GRAY HNDL. & 316SS
BULKHEAD RETAINING NUT
PVCV34FM
PVC VALVE 3/4in FPT X 3/4in MPT
PW124-120
1/2in BLACK POLY PRO X 4in - SCH.120 - 1/2in MPTOE & 1/4in FPTOE
R25
FILTER REGULATOR COMBO INCLUDES AFR25 AND ABR25
SC1212
S.S. COUPLER 1/2in BY 1/2in
SHW3
3in LONG COATED WEIGHT
SSAXLE12
12 9/16IN x 1/2IN STAINLESS STEEL AXLE FOR 10 GALLON UNIT
ST2520
VEEJET NOZZLE, BRASS 2520
STR14
40 MESH SUCTION LINE STRAINER
TANK 10
10 GALLON ROTOMOLDED TANK
W10
6 in wheel X 1.25 in TPR Celcon Brg 1/2 in Axle
SGA14
SANITIZER GUN ASSEMBLY (INCLUDES ITEM # HBSS1238, PSG12, PW124-120 and ST2520)
SI-10
SAFETY INSTRUCTIONS
1.
ALWAYS WEAR SAFETY GOGGLES AND PROTECTIVE GLOVES WHILE OPERATING FOAM UNIT.
2.
AVOID CONTACT OF CLEANING AGENT WITH SKIN AND EYES. IF CONTACT OCCURS RINSE AFFECTED AREA
WITH WATER FOR 15 MINUTES AND GET MEDICAL ATTENTION IF NEEDED.
3.
AFTER USE, RELIEVE ALL REMAINING PRESSURE IN THE SYSTEM BY UNPLUGGING THE AIR LINE FROM THE
UNIT (AP25) AND OPENING THE DISCHARGE SPRAY GUN (PSG12) UNTIL ALL PRESSURE IS GONE.
4.
NEVER POINT THE DISCHARGE WAND AT ANYONE.
OPERATION INSTRUCTIONS
1.
FILL THE TANK WITH DESIRED SPRAY SOLUTION.
2.
PLUG AN AIR LINE INTO THE AIR INLET FITTING (AP25)
3.
HOLD THE DISCHARGE SPRAY GUN (PSG12) SECURELY IN HAND AND SPRAY DESIRED AREA.
WARNING: NEVER POINT THE DISCHARGE WAND AT ANYONE.
4.
RELIEVE PRESSURE FROM DISCHARGE HOSE AFTER USE.
NOTE: AFTER SPRAYING HARSH CHEMICALS, IT IS RECOMMENDED THAT YOU RUN AT LEAST ONE GALLON
OF WATER THROUGH THE UNIT.
ACCEPTABLE PRODUCTS
UNACCEPTABLE PRODUCTS
• ALKALINE CLEANERS
• ALL HYDROCARBONS
• CAUSTIC CLEANERS
• D-LIMONENE
• SANITIZERS
• ACIDS
Download PDF