EN
User Manual
2
USER
MANUAL
Cooler
ZRG11600WA
ZANUSSI
Contents
Safety information����������������������������������2
Safety instructions����������������������������������3
Product description���������������������������������5
Correctly positioning�������������������������������5
Using your refrigerator����������������������������6
Door reversibility�������������������������������������7
Cautions�������������������������������������������������8
Changing the bulb����������������������������������8
Maintenance�������������������������������������������8
Troubleshooting��������������������������������������9
Electrical connection����������������������������10
Environmental concerns�����������������������11
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for
future reference.
Children and vulnerable people safety
•This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
•Do not let children play with the appliance.
•Keep all packaging away from children.
•Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
•This appliance is intended to be used in household and similar applications such as:
––Farm houses; staff kitchen areas in shops, offices and other
working environments
––By clients in hotels, motels, bed and breakfast and other
residential type environments
•Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
EN
2
•Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by the
manufacturer.
•Do not damage the refrigerant circuit.
•Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type
recommended by the manufacturer.
•Do not use water spray and steam to clean the appliance.
•Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
•Do not store explosive substances such as aerosol cans with
a flammable propellant in this appliance.
•If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
•If the appliance is equipped with an Ice maker or a water dispenser, fill them with potable water only.
•If the appliance requires a water connection, connect it to
potable water supply only.
•The inlet water pressure (minimum and maximum)must be
between 1 bar (0,1 MPa) and 10 bar (1 MPa).
Safety Instructions
Installation
WARNING!
Only a qualified person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied with
the appliance.
• Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
• Make sure the air can circulate around the
appliance.
• Wait at least 4 hours before connecting the
www.zanussi.com
•
•
•
•
•
appliance to the power supply. This is to allow
the oil to flow back in the compressor.
Do not install the appliance close to radiators
or cookers, oven or hobs.
The rear of the appliance must stand against
the wall.
Do not install the appliance where there is
direct sunlight.
Do not install this appliance in areas that
are too humid or too cold, such as the
construction appendices, garages or wine
cellars.
When you move the appliance, lift it by the
front edge to avoid scratching the floor.
3
EN
Electrical connection
WARNING!
Risk of fire and electrical shock.
• The appliance must be earthed.
• All electrical connections should be made by a
qualified electrician.
• Make sure that the electrical information on
the rating plate agrees with the power supply.
If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the electrical components (e.g. mains plug, mains cable,
compressor). Contact the Service or an electrician to change the electrical components.
• The mains cable must stay below the level of
the mains plug.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after the
installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Use
WARNING!
Risk of injury, burns, electrical shock or
fire.
• Do not change the specification of this appliance.
• Do not put electrical appliances (e.g. ice
cream makers) in the appliance unless they
are stated applicable by the manufacturer.
• Be careful not to cause damage to the refrigerant circuit. It contains isobutane (R600a), a
natural gas with a high level of environmental
compatibility. This gas is flammable.
• If damage occurs to the refrigerant circuit,
make sure that there are no flames and
sources of ignition in the room. Ventilate the
room.
• Do not let hot items to touch the plastic parts
of the appliance.
• Do not put soft drinks in the freezer compartment. This will create pressure on the
drink container.
• Do not put flammable products or items that
are wet with flammable products in, near or on
the appliance.
• Do not touch the compressor or the condenser. They are hot.
EN
4
• Do not remove or touch items from the freezer
compartment if your hands are wet or damp.
• Do not freeze again food that has been
thawed.
• Obey the storage instructions on the packaging of frozen food.
Internal light
• The type of light bulb or halogen lamp used
for this appliance, is only for household appliances. Do not use it for house lighting.
Care and cleaning
WARNING!
Risk of injury or damage to the appliance.
• Before maintenance, deactivate the appliance
and disconnect the mains plug from the mains
socket.
• This appliance contains hydrocarbons in the
cooling unit. Only a qualified person must do
the maintenance and the recharging of the
unit.
• Regularly examine the drain of the appliance and if necessary, clean it. If the drain is
blocked, defrosted water collects in the bottom
of the appliance.
Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door to prevent children and pets
to be closed inside of the appliance.
• The refrigerant circuit and the insulation materials of this appliance are ozone-friendly.
• The insulation foam contains flammable gas.
Contact your municipal authority for information on how to discard the appliance correctly.
• Do not cause damage to the part of the cooling unit that is near the heat exchanger.
Product description
10
9
8
1
2
3
4
NOTE: This figure is only a sketch of the
refrigerator, the actual product may differ
from it.
7
WARNING!
Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction.
6
Do not user mechanical devices or
other means to accelerate the defrosting
process.
5
Parts and features
Do not use electrical appliances inside
the food storage compartments of the
appliance.
1 Top cover
2 Removable glass shelves
3 Glass panel
4 Crisper
5 Levelling legs
6 Lower rack
7 Bottle blind rack
8 Recessed handle
9 Light switch
10 Light
Correctly positioning
Well ventilating
Power supply
There is need of good ventilation around the
refrigerator for easy dissipation of heat, high efficiency of refrigeration and low power consumption.
For this purpose, sufficient clear space should be
needed around the
refrigerator, its back is at least 100mm away
from the wall, its sides at least have a space of
200mm separately and the height from over its
top is not less than 300mm. A clear space should
be left to open its doors to 160°.
The refrigerator is only applied with power supply of single phase alternating current (See the
rating label).
If fluctuation of voltage in the district user is of
so large that the voltage exceeds the scope, for
safety sake, be sure to apply A.C. automatic voltage regulator to the refrigerator. The refrigerator
must employ a special power socket instead of
common one other electric appliances. Its plug
must match the socket with ground wire.
www.zanussi.com
5
EN
Power line cord
Protection from heat
The cord should be neither lengthened nor
folded into coil during operation. Moreover, it
is forbidden that cord is kept close onto the
compressor at the back of the refrigerator, the
surface temperature of which is quite high when
operating. Touching with it would deactivate
the insulation or cause leakage for electricity.
Extension cord is not recommended to use. The
appliance must be positioned so that the plug is
accessible.
The refrigerator should be far away from any
heat source or direct sunshine.
WARNING!
If the power cord is damaged, it must be
replaced by the manufacturer or its service agent or a similarly qualified person
in order to avoid a hazard.
Protection from moisture
Avoiding placing the refrigerator in a place where
heavy moisture is present so as to minimize
possibility of rusty for its metal parts. Still more,
the refrigerator is forbidden to be directly sprayed
by water, otherwise, poor insulation and current
leakage would occur.
Fixing stable
Floor on which refrigerator will be placed must
be flat and solid. It should not be laid on any soft
material such as foam plastic, etc. If the refrigerator is not on the same level, adjust the screws
suitably. The refrigerator should not be placed
near anything which may echo.
Keep a way from danger
It is inadvisable that the refrigerator is placed
near any volatilizable or combustibles such as
gas, petrol, alcohol, lacquer and banana oil, etc.
The above-mentioned objects can not be stored
in the refrigerator.
Moving
When fixed or moved, the refrigerator can not be
set horizontally or declined to more than 45° or
upside-down.
Using your refrigerator
Temperature control
• The first time you turn the unit on, set the
temperature control to “7” position.
• The settings of the temperature control are
“0,1,2,3,4,5,6,7”. After 20 minutes, adjust the
temperature control setting to “4”. The setting
of “4” should be correct for home or office use
• To turn the refrigerator off, turn the temperature control to “0”.
NOTE: Turning the temperature control
to “0” position stops the cooling cycle,but
does not shut off the power to the refrigerator.
EN
6
Temperature is at
medium cold
• If the unit is unplugged, power lost, or turned
off, you must wait 3 to 5 minutes before
restarting the unit. If you attempt to restart
before this time delay, the refrigerator will not
start.
• You should put your appliance in the coolest
place in your room, which can save energy
consumption of your appliance. If the environment temperature is too high, the temperature
in the refrigerator may not get the target
temperature.
Door reversibility
This refrigerator has the capability of either opening the door from the left or right side. This unit is
delivered to you with the door opening from the
left side. Should you desire to reverse the opening direction, please follow these instructions.
NOTE: All parts removed must be saved
to do the reinstallation of the door.
13.Keep the door open, raise the end of the
top cover, pull it (10) backwards to hitch the
block (9).
14.After the assembly of the top cover, close
the door, fix the top cover (10) with the screw
(11).
11
Reversal Refrigerator Door
1. Remove the screw nails (11).
2. Keep the door open, raise the end of the top
cover, push it (10) frontad and take it off from
the block (9) of the top cover, then move the
bottom block (8).
3. Remove the two screws blot (6) that connect
the upper hinge (5) on the right side of the
cabinet top.
4. Carefully lift the door and place it on a padded surface to prevent scratching.
5. Remove the plug (7) and transfer it to the uncovered hole on the right side of the unit. Be
sure to press the button firmly into the hole.
6. Remove the two screws (6) that hold the
lower hinge (2) on the right side of the unit.
7. Remove the screw-type leveling front leg (4)
and transfer it to the right side as shown in
the adjacent figure.
8. Set the door into it’s new place making sure
the pin enters the bushing at the lower frame
section (hole).
9. Secure the upper hinge (5) previously
removed in step 3 on the left side of the unit.
Make sure the pin enters the bushing on the
upper frame section (hole).
10.Loosely secure the lower left hinge (2) and
do not tighten the bolts until the door is in the
closed position and leveled.
11.Insert the plug (7) on the uncovered holes
(right side).
12.Fix the decoration block (8) in the right of the
top cover plate (10).
www.zanussi.com
10
9
6
7
5
8
2
4
1
3
1 Screw
2 Low hinge
3 Upper hinge
4 Adjustable low foot
5 Adjustable high foot
6 Screw bolt
7 Plug
8 Decoration block
9 The block of the top cover
10 Top cover plate
11 Screw nail
7
EN
Cautions
Defrosting
The fridge defrosts automatically
The rear wall of the fridge covers with frost
when the compressor is running,and defrosts
when the compressor is off.The water from the
thawing frost evaporates by itself. If the supply
cord of this appliance is damaged, it must only
be replaced by professional person or the repair
shopappointed by the manufacturer.
Before you throw away your old refrigerator: take
off the door, leave the shelves in place, so that
children may not easily climb inside it. Never allow children to operate, play with, or crawl inside
the appliance.
Changing the bulb
• UNPLUG FROM THE MAINS.
• The electric light bulb is inside, at the top of
the refrigerator.
• Remove the shelves and any food/drink.
• Take plastic cover off and unscrew the light
bulb anticlockwise to remove.
• Replace with a new 1,5 watt 220/240volt bulb.
Electric light bulb just behind the
temperature control.
Maintenance
• The refrigerator should be cleaned and maintained once a month.
• When performing maintenance, make absolutely sure that the power plug is first disconnected from the power outlet.
• Wipe the inner and outer surface of the
refrigerator and its accessories with wet cloth.
If they are too dirty, scrub them with neutral
detergent, and then clean them with water and
dry them with clean cloth. After this, a small
quantify of glass wax is recommended to polish the refrigerator surface with a flannelette.
• For cleaning, don’t use hot water, diluent,
petrol, alcohol, kerosene, washing powder,
cleanser, alkaline detergent, acid, Chemical
EN
8
cloth, etc. So as not to damage the lacquer
coat and plastics. It is forbidden than the
refrigerator is directly sprayed with water.
Otherwise, it would cause rusty or weaken the
insulation.
• Be careful to upkeep the sealing rubber bars
of the doors. They should always be cleaned.
• If the plastic parts in refrigerator remain
contaminated for a long time by oil (animal or
vegetable), they will be easy aged and possibly cracked. The drain pan gets dirty very
easily if it is not cleaned regularly, bad odours
will be produced, get into the habit of cleaning
this pan regularly.
Troubleshooting
1. When the refrigerator does not work.
Check if there is a power failure. Check if the
power plug is plugged into the power outlet.
Check that the fuse has not blown.
2. When the refrigerator is cooling excessively. The temperature control dial may be
set too high.
3. When the refrigerator is not cooling sufficiently. The food may be packed too tightly
together which will block the flow of cool air.
You may have put something hot or a lot of
food stuffs into the refrigerator. The door may
not have been closed properly. The door
gaskets may be damaged. The refrigerator
may not be ventilated. There may be insufficient clearance between the refrigerator
and the surfaces immediately both sides and
above. The temperature control dial may not
be set properly.
4. When the defrosting water overflows
inside the refrigerator and onto the floor.
Check that the drain pipe and the drain hose
are not clogged. Check that the drain pan is
housed properly.
5. When the refrigerator’s cabinet front
heats up. In order to safeguard against
www.zanussi.com
condensation, there is an anticondensation,
pipe which heats up the cabinet front when
running actuated. A warm cabinet front does
not indicate a malfunction.
6. When condensation form on the outside
of the refrigerator. Condensation may form
on the outside when the humidity is high
such as during a wet season. This is the
same result as the condensation formed
when chilled water is poured into a glass. It
does not, therefore, indicate a failure, wipe
dry with a dry cloth.
7. When you hear a sound like water
flowing. A sound like water flowing is the
refrigerant flowing. It does not Indicate a
malfunction.
8. When the cabinet’s side panel heats up.
The side panel of the cabinet will heat up
when the door is opened or closed frequently, when starting the unit and when the
unit operates in summer with high ambient
outside temperature, In such case, do not
touch the panel, it results from the dissipation of the heat from inside the cabinet, and it
does not mean that something is wrong with
the refrigerator.
9
EN
Electrical connection
CAUTION!
Any electrical work required to install
this appliance should be carried out by a
qualified electrician or competent person.
WARNING!
This appliance must be earthed.
The manufacture declines any liability
should these safety measures not be
observed.
2
1
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1. Connect the wire coloured green and yellow
to the terminal marked either with the letter
“E” or by the earth symbol
or coloured
green and yellow.
2. Connect the wire coloured blue to the
terminal either marked with the letter “N” or
coloured black.
3. Connect the wire coloured brown to the terminal either marked with the “L” or coloured
red.
4. Check that no cut, or stray strands of wire
is present and the cord clamp 4 is secure
over the outer sheath.
3
5
4
IMPORTANT!
The wires in the mains lead are colored in
accordance with the following code:
1 Green and Yellow: Earth
3 Brown: Live
5 Blue: Neutral
EN
10
5. Make sure the electricity supply voltage is
the same as that indicated on the appliance
rating plate.
6. Switch on the appliance.
The appliance is supplied with a 13 amp plug fitted 2 . In the event of having to change the fuse
in the plug supplied, a 13 amp ASTA approved
(BS 1362) fuse must be used.
WARNING!
A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that it is disposed of safety.
Environmental concerns
The symbol
on the product or on its packaging indicates that this product may not be treated
as household waste. Instead it should be taken
to the appropriate collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product.
www.zanussi.com
For more detailed information about recycling of
this product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Packaging materials
The materials with the symbol
are
recyclable. Dispose of the packaging in suitable
collection containers to recycle it.
Disposal of the appliance
1. Disconnect the mains plug from the mains
socket.
2. Cut off the mains cable and discard it.
11
EN
www.zanussi.com/shop