ENGLISH
FRANÇAIS
ESPAÑOL
KD-X320BTS
DIGITAL MEDIA RECEIVER
Please read all instructions carefully before
operation to obtain the best possible performance
from the unit.
Veuillez lires les instructions attentivement avant
d’utiliser l’appareil afin d’obtenir les meilleures
performances possibles de l’appareil.
Por favor lea detenidamente este manual para
comprender a fondo todas las instrucciones y
obtener un máximo disfrute de esta unidad.
INSTRUCTION MANUAL
RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE
MANUEL D’INSTRUCTIONS
RECEPTOR DE MEDIOS DIGITALES
MANUAL DE INSTRUCCIONES
For customer Use:
Enter below the Model No. and Serial No. which are
located on the top or bottom of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
B5A-0117-00 [J]
JS_JVC_KD_X320BTS_J_C.indd 1
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
24/9/2014 4:55:49 PM
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de
la vida útil (aplicable a los países que hayan adoptado sistemas independientes de
recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no
podrán ser desechados como residuos domésticos. Los equipos eléctricos y
electrónicos al final de la vida útil, deberán ser reciclados en instalaciones
que puedan dar el tratamiento adecuado a estos productos y a sus
subproductos residuales correspondientes. Póngase en contacto con su
administración local para obtener información sobre el punto de recogida
más cercano. Un tratamiento correcto del reciclaje y la eliminación de
residuos ayuda a conservar los recursos y evita al mismo tiempo efectos
perjudiciales en la salud y el medio ambiente.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not installed and used in
accordance with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada
ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou
importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos
naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio
ambiente.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—
special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
i
JS_JVC_KD_X320BTS_J_C.indd i
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:32 PM
Para cumplimiento de la COFETEL:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada”
IC (Industry Canada) Notice
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
The term “IC: ” before the certification/ registration number only signifies that the Industry
Canada technical specification were met.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement
que les specifications techniques d’Industrie Canada ont été respectées.
Contains Bluetooth Module
Contains Bluetooth Module
FCC ID: ZWYMC55
IC:
12033A-MC55
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C
to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very
low levels of RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated keeping the
radiator at least 20cm or more away from person’s body (excluding extremities: hands,
wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui
est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant,
cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre
le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et
chevilles).
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé
pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l’intensité nécessaire à l’établissement d’une communication satisfaisante.
ii
JS_JVC_KD_X320BTS_J_C.indd ii
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:32 PM
CONTENTS
BEFORE USE
BEFORE USE
2
BASICS
3
GETTING STARTED
4
USB / iPod / ANDROID
5
RADIO
7
AUX
8
Pandora®
9
iHeartRadio®
10
SiriusXM® Radio
11
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short
circuit.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
BLUETOOTH®
14
AUDIO SETTINGS
20
DISPLAY SETTINGS
22
MORE INFORMATION
23
TROUBLESHOOTING
24
SPECIFICATIONS
27
How to read this manual
INSTALLATION /
CONNECTION
28
• Operations are explained mainly using buttons on the faceplate.
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft
cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector.
Connector (on the reverse
side of the faceplate)
2
JS_JVC_KD_X320BTS_J_EN_2.indd 2
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:48 PM
BASICS
Faceplate
Remote control (RM-RK52)
Attach
Volume knob
(turn/press)
Display window
Remote sensor (Do not expose
to bright sunlight.)
Detach
Pull out the insulation sheet
when using for the first time.
How to reset
How to replace the battery
Detach button
Your preset adjustments
will also be erased.
To
On the faceplate
Turn on the power
Press
.
• Press and hold to turn off the power.
Adjust the volume
On the remote control
—
Turn the volume knob.
Press
Press the volume knob to mute the sound or pause playback.
• Press again to cancel.
Press
to mute the sound or pause playback.
• Press again to cancel.
Select a source
• Press
• Press
repeatedly.
, then turn the volume knob within 2 seconds.
Press SOURCE repeatedly.
Change the display
information
Press
repeatedly. ( 24)
or
.
—
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2A.indd 3
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
3
18/9/2014 12:29:39 PM
GETTING STARTED
Default: XX
SETTINGS
BEEP
ON: Activates the keypress tone. ; OFF: Deactivates.
SRC SELECT
1
1
2
3
4
Cancel the demonstration
Press and hold
.
Turn the volume knob to select [DEMO], then press the knob.
Turn the volume knob to select [DEMO OFF], then press the knob.
Press
to exit.
AM *
ON: Enables AM in source selection. ; OFF: Disables.
PANDORA *
ON: Enables PANDORA in source selection. ; OFF: Disables.
IHEART *
ON: Enables IHEARTRADIO in source selection. ; OFF: Disables.
AUX *
ON: Enables AUX in source selection. ; OFF: Disables.
F/W UPDATE
SYSTEM / BLUETOOTH
2
F/W xxxx
Set the clock
1
2
3
4
Press and hold
.
Turn the volume knob to select [CLOCK], then press the knob.
Turn the volume knob to select [CLOCK SET], then press the knob.
Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [24H/ 12H], then press the knob.
6 Turn the volume knob to select [12 HOUR] or [24 HOUR], then press the
knob.
7 Press
to exit.
To return to the previous setting item, press
.
YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
CLOCK
CLOCK SYNC
AUTO: The clock time is automatically set using the Clock Time (CT) data
in FM Radio Broadcast Data System signal. ; OFF: Cancels.
CLOCK DISP
ON: The clock time is shown on the display even when the unit is turned
off. ; OFF: Cancels.
* Not displayed when the corresponding source is selected.
3 Set the basic settings
.
1 Press and hold
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press
to exit.
To return to the previous setting item, press
.
4
JS_JVC_KD_X320BTS_J_EN_2A.indd 4
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
18/9/2014 12:29:41 PM
USB / iPod / ANDROID
Start playback
The source changes automatically and
playback starts.
USB input terminal
USB
USB 2.0 cable*1
(commercially available)
iPod/iPhone
To
On the faceplate
Reverse / Fast-forward*3
Press and hold
Select a file
Press
.
Press
Select a folder*4
Press
.
Press
Repeat play*5
Press
repeatedly.
TRACK RPT/ RPT OFF
Random play*5
Micro USB 2.0 cable*1
(commercially available)
Press and hold
.
.
.
: JVC Playlist Creator (JPC) / JVC Music
Control (JMC) file ( 24)
TRACK RPT/ FOLDER RPT/ RPT OFF : MP3/WMA/AAC/WAV/FLAC file
ONE RPT/ ALL RPT/ RPT OFF
: iPod or ANDROID
(Accessory of the iPod/
iPhone)*1
ANDROID*2
On the remote control
.
Press
repeatedly.
FOLDER RND/ ALL RND/ RND OFF : MP3/WMA/AAC/WAV/FLAC file or JPC /
JMC file
SONG RND/ ALL RND/ RND OFF
: iPod or ANDROID
*1 Do not leave the cable inside the car when not using.
*2 When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
( 23)
*3 For ANDROID: Applicable only when [AUTO MODE] is selected. ( 6)
*4 Only for MP3/WMA/AAC/WAV/FLAC files. This does not work for iPod/ ANDROID.
*5 For iPod/ ANDROID: Applicable only when [HEAD MODE]/ [AUTO MODE] is selected. ( 6)
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2A.indd 5
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
5
18/9/2014 12:29:41 PM
USB / iPod / ANDROID
To
On the faceplate
Select control
mode
While in iPod source, press
repeatedly.
HEAD MODE: Control from the unit.
IPHONE MODE: Control from the iPod/iPhone. However, you
can still play/pause or file skip from the unit.
While in ANDROID source, press
repeatedly.
AUTO MODE: Control from the unit (using JVC MUSIC
PLAY application).
AUDIO MODE: Control other media player applications
from the Android device (without using JVC
MUSIC PLAY application). However, you can
still play/pause or file skip from the unit.
Select music
drive
Press
repeatedly.
The stored songs in the following start playback.
• Selected internal or external memory of a smartphone
(Mass Storage Class).
• Selected drive of a multiple drives device.
Change the playback speed of the Audiobook
While listening to the iPod and [HEAD MODE] is selected ( Select control mode)....
1 Press and hold
.
2 Turn the volume knob to select [IPOD], then press the knob.
3 Press the volume knob to select [AUDIOBOOKS].
4 Turn the volume knob to make a selection, then press the knob.
0.5× SPEED / 1× SPEED / 2× SPEED: Select the desired playback speed of the
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
5 Press
to exit.
To return to the previous setting item, press
.
Select a file from a folder/list
.
1 Press
2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA/AAC/WAV/FLAC or JPC / JMC file:
Turn the volume knob quickly.
For iPod:
You can search for a file according to the first character.
Press
or turn the volume knob quickly to select the
desired character (A to Z/ 0 to 9/ OTHERS).
• Select “OTHERS” if the first character is other than A to Z,
0 to 9.
• To return to the previous setting item, press
.
• To cancel, press and hold
.
• For iPod, applicable only when [HEAD MODE] is selected. ( Select
control mode)
• For ANDROID, applicable only when [AUTO MODE] is selected.
( Select control mode)
6
JS_JVC_KD_X320BTS_J_EN_2.indd 6
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:53 PM
RADIO
Other settings
.
1 Press and hold
2 Turn the volume knob to select [TUNER], then press the
knob.
3 Turn the volume knob to make a selection (see the
following table), then press the knob.
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
repeatedly to select FM or AM.
1 Press
2 Press
(or press
on RM-RK52) to search for a station automatically.
(or)
Press and hold
(or press and hold
on RM-RK52) until “M” flashes,
then press repeatedly to search for a station manually.
4 Repeat step 3 until the desired item is selected/
activated or follow the instructions stated on the
selected item.
5 Press
to exit.
To return to the previous setting item, press
.
Default: XX
RADIO TIMER
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1 to 6).
(or)
1 Press and hold the volume knob until “PRESET MODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Turns on the radio at a specific time regardless of the
current source.
1 ONCE/ DAILY/ WEEKLY/ OFF: Select how often the
timer will be turned on.
2 FM/ AM/ SIRIUS XM *1: Select the source.
3 01 to 18 (for FM/ SIRIUS XM)/ 01 to 06 (for
AM): Select the preset station.
4 Set the activation day *2 and time.
“M” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AM] in [SRC SELECT] after Radio
Timer for AM is selected. ( 4)
*1 Selectable only when SiriusXM Vehicle Tuner is connected. ( 11)
*2 Selectable only when [ONCE] or [WEEKLY] is selected in step 1.
Select a stored station
Press one of the number buttons (1 to 6).
(or)
1 Press
2 Turn the volume knob to select a preset number, then press the knob to
confirm.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2A.indd 7
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
7
18/9/2014 12:29:47 PM
AUX
RADIO
Default: XX
SSM
SSM 01 – 06 / SSM 07 – 12 / SSM 13 – 18: Automatically presets up
to 18 stations for FM. “SSM” stops flashing when the first 6 stations are
stored. Select SSM 07 – 12 / SSM 13 – 18 to store the following 12
stations.
IF BAND
AUTO: Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
MONO
ON: Improves the FM reception, but the stereo effect will be lost. ;
OFF: Cancels.
AREA
AREA US: For North/Central/South America, AM/FM intervals:
10 kHz/200 kHz. ; AREA SA: For some South American countries, AM/
FM intervals: 10 kHz/50 kHz. ; AREA EU: For any other areas, AM/FM
intervals: 9 kHz/50 kHz.
PTY SEARCH*3
Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
Use a portable audio player
1 Connect a portable audio player (commercially available).
3.5 mm (1/8") stereo mini plug with “L” shaped connector
(commercially available)
Auxiliary input jack
Portable audio player
2 Select [ON] for [AUX] in [SRC SELECT]. ( 4)
3 Press
repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
PTY code: NEWS, INFORM (information), SPORTS, TALK, ROCK, CLS ROCK (classic
rock), ADLT HIT (adult hits), SOFT RCK (softrock), TOP 40, COUNTRY, OLDIES, SOFT,
NOSTALGA (nostalgia), JAZZ, CLASSICL (classical), R & B (rhythm and blues),
SOFT R&B (soft rhythm and blues), LANGUAGE, REL MUSC (religious music),
REL TALK (religious talk), PERSNLTY (personality), PUBLIC, COLLEGE, HABL ESP
(Spanish talk), MUSC ESP (Spanish music), HIP HOP, WEATHER
*3 Only for FM source.
8
JS_JVC_KD_X320BTS_J_EN_2.indd 8
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:54 PM
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [ON] for [PANDORA] in [SRC SELECT]. ( 4)
Create and save a new station
.
1 Press
2 Turn the volume knob to select [NEW STATION], then press the knob.
3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then
press the knob.
A new station is created based on the current song or artist.
4 Press and hold number button 1, 4, 5 or 6 to store.
To select a stored station, press number button 1, 4, 5 or 6.
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
USB input terminal
Search for a registered station
.
1 Press
2 Turn the volume knob to make a selection, then press the knob.
[BY DATE]: According to the registered date.
[A-Z]:
Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold
.
(Accessory of the iPod/iPhone)*1
The source changes to PANDORA and broadcast starts.
To
On the faceplate
On the remote control
Playback / pause
Press the volume knob.
Press
Skip a track
Press T.
Thumbs up or
thumbs down*2
Press
Bookmark a song or artist information
1 Press and hold the volume knob.
2 Turn the volume knob to make a selection, then press the knob.
.
Press I.
.
*1 Do not leave the cable inside the car when not using.
*2 If thumbs down is selected, the current track is skipped.
Press
.
[THIS TRACK]: Current song information
[THIS ARTIST]: Current artist information
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this
unit.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 9
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
9
11/9/2014 4:57:55 PM
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for JVC application on your device (iPhone/ iPod
touch), then create an account and log in to iHeartRadio.
• Select [ON] for [IHEART] in [SRC SELECT]. ( 4)
Search for a station
.
1 Press
2 Turn the volume knob to select a category, then
press the knob.
3 Turn the volume knob to the desired station, then
Start listening
1 Open the iHeart Link application on your device.
2 Connect your device to the USB input terminal.
press the knob.
When a city list appears, you can skip cities in
alphabetical order.
To cancel, press and hold
.
USB input terminal
Skip cities by alphabetical order
(Accessory of the iPod/iPhone)*1
3 Press
repeatedly to select IHEARTRADIO.
Broadcast starts automatically
To
On the faceplate
On the remote control
Playback / pause
Press the volume knob.
Press
Skip a track for custom station
Press T.
Thumbs up or thumbs down
for custom station*2
Press
Create a new/custom station
Press and hold the volume
knob.
.
Press I.
.
Press
.
—
Add to favorite stations for live Press 1.
station
—
Scan for live station
—
Press 4.
While a city list appears during search...
1 Turn the volume knob quickly to enter character
search.
You can search through the list quickly according to
the first character (A to Z).
2 Turn the volume knob or press
to select the
character to be search for.
3 Press the volume knob to start searching.
To cancel, press and hold
.
*1
Do not leave the cable inside the car when not using.
*2 If thumbs down is selected, the current track is skipped.
10
JS_JVC_KD_X320BTS_J_EN_2.indd 10
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:55 PM
SiriusXM® Radio
Only SiriusXM® brings you more of what you love
to listen to, all in one place. Get over 140 channels,
including commercial-free music plus the best sports,
news, talk, comedy and entertainment. Welcome to the
world of satellite radio. A SiriusXM Vehicle Tuner and
Subscription are required. For more information, visit
www.siriusxm.com.
Start listening
1 Press
2 Press
.
Preparation:
1 Connect the optional SiriusXM Vehicle Tuner
(commercially available).
5 Turn the volume knob to select a channel, then press the knob.
repeatedly to select SIRIUS XM.
“ ” lights up.
3 Turn the volume knob to select a CATEGORY, then press the knob.
4 Turn the volume knob to select a category from the list, then press the knob.
If “ALL CHANNEL” is selected, all the available channels will be shown.
Antenna
Expansion port on
the rear panel
SiriusXM
Vehicle Tuner
2 Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and
can be found by tuning to Channel 0 as well as on
the label found on the SiriusXM Connect tuner and
its’ packaging.
The Radio ID does not include the letters I, O, S or F.
3 Activate the subscription.
For users in U.S.A.:
Online: Go to www.siriusxm.com
Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to www.siriusxm.ca/activatexm
Phone: Call 1-877-438-9677
4 Press
repeatedly to select SIRIUS XM
to start updating.
(or)
Press
to search for a channel manually.
• Pressing and holding
changes the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears.
Enter the pass code to receive the channel. ( 13)
Store a channel
You can store up to 18 channels.
To
Store a channel
Select a stored
channel
Do this
Press and hold one of the number buttons (1 to 6).
1 Press and hold the volume knob until “PRESET MODE” flashes.
2 Turn the volume knob to select a preset number, then press
the knob.
The preset number flashes and “MEMORY” appears.
Press one of the number buttons (1 to 6).
1 Press
.
2 Turn the volume knob to select PRESET, then press the knob.
3 Turn the volume knob to select a preset number, then press
the knob.
Press
on RM-RK52.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 11
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11
11/9/2014 4:57:55 PM
SiriusXM® Radio
When you select a SmartFavorites channel, you can rewind and replay up
to 30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if [TUNE START] is set to
[ON] ( 13) for most music channels stored as a SmartFavorite.
SiriusXM Replay™
1 Press the volume knob.
“
” lights up and the unit memorizes this paused position.
2 Press the volume knob to start Replay.
Replay starts from the paused position in step 1.
To
Select a stored
SmartFavorite
channel
During Replay...
To
On the faceplate
On the remote control
Playback / pause
Press the volume knob.
Press
Skip the current song
backward/forward
Press
Press
Rewind /
Fast-forward
Press and hold
.
Go to Live and exit
Reply
Press and hold the volume knob.
.
.
Press and hold
.
1 Press
.
2 Turn the volume knob to select LIVE, then
press the knob.
On the faceplate
Press one of the number buttons (1 to 6).
1 Press
.
2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset number,
then press the knob to confirm.
Cancel
1 Press
.
SmartFavorites 2 Turn the volume knob to select PRESET, then
channels
press the knob.
3 Turn the volume knob to select a preset number,
then press and hold the knob.
“ * ” are removed from the last character.
Reassign
Repeat steps 1 to 3 of cancelling SmartFavorites
SmartFavorites channels.
channels
“ * ” appears at the last character.
SmartFavorites and TuneStart™
User preset channels are initially assigned as the SmartFavorites channels.
SmartFavorite channel is available with SXV200 or later SiriusXM tuner
models. SiriusXM Vehicle Tuner automatically buffers the broadcast audio
content of the SmartFavorites channels in the background.
• Using SXV200: This unit can assign a maximum of 6 SmartFavorites
channels. If you try to assign the 7th channel, an error beep tone will be
heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.
Using SiriusXM tuner models later than SXV200: This unit can assign
a maximum of 18 SmartFavorites channels. Initially, all preset channels
are assigned as SmartFavorites.
• “ * ” appears at the last character of the channel name for the
SmartFavorites channels.
TuneScan™
You can get a short preview of the songs that you have missed on each of
your SmartFavorite music channels or current tuned music channel.
1 Press
.
2 Turn the volume knob to select TUNE SCAN, then press the knob.
Scanning start for the first 6 seconds of the recorded music contents.
• To listen to the current song, press the volume knob to stop scanning.
The unit continues playing the current song.
• To select the previous/next song, press
.
• To cancel scanning, press and hold the volume knob. Playback returns
to the channel before you enter TuneScan.
12
JS_JVC_KD_X320BTS_J_EN_2.indd 12
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:56 PM
SiriusXM® Radio
SiriusXM settings
.
1 Press and hold
2 Turn the volume knob to select [SIRIUS XM], then press the knob.
3 Turn the volume knob to make a selection (see the following table), then
press the knob.
4 Repeat step 3 until the desired item is selected/activated or follow the
instructions stated on the selected item.
5 Press
to exit.
To return to the previous setting item, press
ON: Selected SmartFavorite channel starts playback from
the beginning of the song. ; OFF: Cancels.
SIGNAL LVL
NO SIGNAL/ WEAK/ GOOD/ STRONG: Shows the strength
of the current received signal.
BUF USAGE
0% — 100% (0): Shows the memory usage for Replay
buffer.
SXM RESET
YES: Resets stored channel and lock setting to default. ;
NO: Cancels.
.
Default: XX
CH LOCK
TUNE START*2
To unlock settings:
1 Turn the volume knob to select a number.
2 Press
to move to the entry position.
3 Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4 Press the volume knob to confirm.
CODE SET
1 Press the volume knob to enter [NEW CODE].
2 Turn the volume knob to select a number.
3 Press
to move to the entry position.
4 Repeat steps 2 and 3 to enter a new 4-digit pass code.
5 Press the volume knob to confirm.
6 Repeat steps 2 to 5 to reconfirm the pass code.
• Make a note of the new pass code to enter channel lock settings from next time.
LOCK SET
MATURE CH: Selects the SiriusXM-defined lock setting. ; USER DEFINED: Selects the
user-defined lock setting. ; OFF: Cancels.
CH EDIT*1
1 Turn the volume knob to select a category, then press the knob.
2 Turn the volume knob to select a channel you want to lock, then press the knob.
“L” appears in front of the channel number.
3 Press and hold
to exit.
CH CLEAR*1
YES: Clears all the locked channels. ; NO: Cancels.
*1 Displayed only when [USER DEFINED] is selected.
*2 Available only if the connected SiriusXM Vehical Tuner is SXV200 or later that
supports SmartFavorites.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 13
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
13
11/9/2014 4:57:56 PM
BLUETOOTH®
BLUETOOTH — Connection
Pair a Bluetooth device
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Rear panel
Microphone
(supplied)
Microphone input jack
Secure using cord clamps
(not supplied) if necessary.
Adjust the microphone
angle
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit
and the device.
1 Press
to turn on the unit.
2 Search and select “JVC UNIT” on the Bluetooth device.
“BT PAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
• Refer also to the manual supplied with your Bluetooth device.
3 Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “VOL – YES” “BACK – NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkey which appears on the unit and Bluetooth device is the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL – YES” “BACK – NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing. ( 18)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the Bluetooth
connection is established.
• Up to five devices can be registered (paired) in total.
• Only one Bluetooth device can be connected at any time.
• This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device
to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you
reset the unit. To delete the paired device, 18, [DELETE PAIR].
• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request
(via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed
the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected devcie is turned on.
– [AUTO CNNT] is set to [ON]. ( 18)
– JVC MUSIC PLAY application is installed on the Android device.
14
JS_JVC_KD_X320BTS_J_EN_2.indd 14
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:56 PM
BLUETOOTH®
BLUETOOTH — Mobile phone
Improve the voice quality
While talking on the phone....
1 Press and hold
.
2 Turn the volume knob to make a selection
(see the following table), then press the
knob.
3 Repeat step 2 until the desired item is
selected or activated.
4 Press
to exit.
To return to the previous setting item, press
.
Receive a call
When there is an incoming call:
– All the buttons flash.
– The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 16)
During a call:
– If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
Default: XX
To
On the faceplate
Answer a call
Press
On the remote control
Reject a call
Press and hold
knob.
or the volume
Press and hold
.
End a call
Press and hold
knob.
or the volume
Press and hold
.
Adjust the phone
volume
[00] to [50] (Default: [15]*)
Turn the volume knob during a call.
• This adjustment will not affect the
volume of the other sources.
—
Switch between handsfree and private talk
modes
Press the volume knob during a call.
• Operations may vary according to the
connected Bluetooth mobile phone.
—
or the volume knob.
Press
MIC LEVEL
–10 — +10 (–4): The sensitivity of
the microphone increases as the number
increased.
NOISE RDCT
–5 — +5 (0): Adjust the noise reduction
level until the least noise is being heard
during a phone conversation.
ECHO CANCEL
–5 — +5 (0): Adjust the echo
cancellation delay time until the least
echo is being heard during a phone
conversation.
.
* Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2A.indd 15
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
15
18/9/2014 12:30:15 PM
BLUETOOTH®
Make the settings for receiving a call
to enter Bluetooth mode.
1 Press
2 Turn the volume knob to make a selection
(see the following table), then press the
knob.
3 Repeat step 2 until the desired item is
selected or activated.
To return to the previous setting item, press
.
Default: XX
SETTINGS
AUTO ANSWER
01 SEC — 30 SEC: The unit answers
incoming call automatically in
the selected time (in seconds). ;
OFF: Cancels.
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also
possible if your mobile phone has the feature.
1 Press
to enter Bluetooth mode.
2 Turn the volume knob to make a selection (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on
the selected item.
To return to the previous setting item, press
.
RECENT CALL
1 Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the volume knob to call.
PHONEBOOK
1 Press
to select the desired letter (A to Z, 0 to 9, and OTHERS).
• “OTHERS” appears if the first character is other than A to Z, 0 to 9.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the
unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
16
JS_JVC_KD_X320BTS_J_EN_2A.indd 16
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
18/9/2014 12:30:16 PM
BLUETOOTH®
DIAL NUMBER
VOICE
1 Turn the volume knob to select a number (0 to 9) or character ( , #,
+).
2 Press
to move the entry position.
Repeat steps 1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
Speak the name of the contact you want to call or the voice command to
control the phone functions. ( Make a call using voice recognition)
Make a call using voice recognition
to activate the connected phone.
1 Press and hold
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of
iPhone.
Delete a contact
to enter Bluetooth mode.
1 Press
2 Turn the volume knob to select [RECENT CALL], then press the knob.
3 Turn the volume knob to select a contact.
4 Press and hold
to enter delete mode.
5 Turn the volume knob to select [DELETE] or [DELETE ALL], then press
the knob.
DELETE: Selected name or phone number in step 3 is deleted.
DELETE ALL: All names or phone numbers in [RECENT CALL] in step 2 is
deleted.
6 Turn the volume knob to select [YES], then press the knob.
• To return to the previous setting item, press
.
• Not applicable for mobile phone that supports PBAP.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press
to enter Bluetooth mode.
2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK], or
[DIAL NUMBER], then press the knob.
3 Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
4 Press and hold one of the number buttons (1 to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select [DIAL NUMBER] in step 2
and store a blank number.
Make a call from memory
to enter Bluetooth mode.
1 Press
2 Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
Bluetooth mode settings
.
1 Press and hold
2 Turn the volume knob to select [BLUETOOTH], then press the knob.
3 Turn the volume knob to make a selection ( 18), then press the
knob.
4 Repeat step 3 until the desired item is selected/activated or follow
the instructions stated on the selected item.
to exit.
To return to the previous setting item, press
.
5 Press
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 17
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
17
11/9/2014 4:57:57 PM
BLUETOOTH®
Default: XX
PHONE*1
AUDIO*1
Selects the phone or audio device to connect or disconnect.
“ ” appears in front of the device name when connected.
APPLICATION*1
Shows the connected phone name using the JVC Smart Music Control *2
app. “ ” appears in front of the device name when connected.
DELETE PAIR
1 Turn the volume knob to select a device to delete, then press the
knob.
2 Turn the volume knob to select [YES] or [NO], then press the knob.
SET PINCODE
(0000)
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
2 Press
to move the entry position.
Repeat steps 1 and 2 until you finish entering the PIN code.
3 Press the volume knob to confirm.
AUTO CNNCT
ON: The unit automatically reconnect when the last connected
Bluetooth device is within range. ; OFF: Cancels.
AUTO PAIR
ON: The unit automatically pair supported Bluetooth device (iPhone/
iPod touch/ Android device) when it is connected through USB input
terminal. Depending on the operating system of the connected device,
this function may not work. ; OFF: Cancels.
INITIALIZE
YES: Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.). ; NO: Cancels.
INFORMATION
MY BT NAME: Displays the unit name (JVC UNIT). ;
MY ADDRESS: Shows address of this unit.
*1 You can only connect another Bluetooth device by disconnecting the connected Bluetooth
device first. “ ” disappears when disconnected.
*2 JVC Smart Music Control is designed to view JVC car receiver status and perform simple
control operations on Android smart phones.
For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold
.
“BLUETOOTH”
“CHECK MODE” appears. “SEARCH NOW USING
PHONE” “PIN IS 0000” scrolls on the display.
2 Search and select “JVC UNIT” on the Bluetooth device within
3 minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same
passkey appears on the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” “[Device Name]” appears and
Bluetooth compatibility check starts.
If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device
to allow phonebook access to continue.
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*1 and/or “A.STREAM OK”*2 and/or
“PBAP OK”*3 : Compatible
*1 Compatible with Hands-Free Profile (HFP)
*2 Compatible with Advanced Audio Distribution Profile (A2DP)
*3 Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has
been deleted, and the unit exits check mode.
• To cancel, press and hold
to turn off the power, then turn
on the power again.
18
JS_JVC_KD_X320BTS_J_EN_2.indd 18
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:58 PM
BLUETOOTH®
BLUETOOTH — Audio
Internet radio via Bluetooth
Listen to Pandora
Preparation:
Select [ON] for [PANDORA] in [SRC SELECT]. ( 4)
You can listen to Pandora on your smart phone
(Android OS) through Bluetooth on this unit.
1 Open the Pandora application on your device.
2 Connect your Bluetooth audio player via
Bluetooth connection. ( 14)
3 Press
repeatedly to select PANDORA.
The source switches and broadcast starts
automatically.
You can operate Pandora in the same way as Pandora
for iPod/iPhone. ( 9)
Audio player via Bluetooth
repeatedly to select BT AUDIO (or press SOURCE on RM-RK52).
1 Press
2 Operate the Bluetooth audio player to start playback.
To
On the faceplate
On the remote control
Playback / pause
Press
Press
.
Select group or folder
Press
.
Press
Reverse /
Forward skip
Press
.
Press
.
.
.
Listen to iHeartRadio
.
Reverse / Fast-forward
Press and hold
Repeat play
Press
repeatedly.
TRACK RPT, ALL RPT, RPT OFF
—
Random play
repeatedly.
Press
GROUP RND, ALL RND, RND OFF
—
Press and hold
Operations and display indications may differ according to their availability on the
connected device.
.
Preparation:
Select [ON] for [IHEART] in [SRC SELECT]. ( 4)
You can listen to iHeartRadio on your smart phone
(Android OS) through Bluetooth on this unit.
1 Open the iHeart Link application on your smart
phone.
2 Connect your smart phone via Bluetooth
connection. ( 14)
3 Press
repeatedly to select
IHEARTRADIO.
The source switches and broadcast starts
automatically.
You can operate iHeartRadio in the same way as
iHeartRadio for iPod/iPhone. ( 10)
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2A.indd 19
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
19
18/9/2014 12:30:22 PM
AUDIO SETTINGS
To
On the faceplate
Select a preset
equalizer
Press
Store your own
sound settings
Default: XX
EQ SETTING
repeatedly.
Press
, then turn the volume knob
within 2 seconds.
Preset equalizer: FLAT (default), HARD ROCK, JAZZ, POP,
R&B, TALK, USER1, USER2, VOCAL BOOST, BASS BOOST,
CLASSICAL, DANCE
EQ PRESET
FLAT / HARD ROCK / JAZZ / POP / R&B / TALK / USER1 / USER2 /
VOCAL BOOST / BASS BOOST / CLASSICAL / DANCE: Selects a preset
equalizer.
EASY EQ
1 USER1/ USER2: Select a preset name.
2 Adjust your own sound settings.
SUB.W SP *1*2:
00 to +06
SUB.W *1*3:
–08 to +08
BASS LVL:
–06 to +06
MID LVL:
–06 to +06
TRE LVL:
–06 to +06
1 Press and hold
.
2 Turn the volume knob to select [EASY EQ], then
press the knob.
3 Turn the volume knob to select [USER1] or
[USER2], then press the knob.
4 Turn the volume knob to make a selection,
then press the knob.
For settings, refer to step 2 of [EASY EQ].
• To return to the previous setting item, press
• To exit, press
.
PRO EQ
.
Other settings
.
1 Press and hold
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
to exit.
To return to the previous setting item, press
.
4 Press
(Default: 03
00
00
00
00)
1 USER1/ USER2: Select a preset name.
2 BASS / MIDDLE / TREBLE: Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
(Default: 80 HZ
BASS
Frequency: 60/ 80/ 100/ 200 HZ
Level:
–06 to +06
00
Q:
Q1.0/ Q1.25/ Q1.5/ Q2.0
Q1.0)
MIDDLE Frequency: 0.5/ 1.0/ 1.5/ 2.5 KHZ
(Default: 1.0 KHZ
Level:
–06 to +06
00
Q:
Q0.75/ Q1.0/ Q1.25
Q1.25)
TREBLE Frequency: 10.0/ 12.5/ 15.0/ 17.5 KHZ (Default: 10.0 KHZ
Level:
–06 to +06
00
Q:
Q FIX
Q FIX)
*1 Displayed only when [SUB.W] is set to [ON]. ( 21)
*2 Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W]. ( 21)
*3 Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W]. ( 21)
20
JS_JVC_KD_X320BTS_J_EN_2.indd 20
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:57:59 PM
AUDIO SETTINGS
AUDIO
BASS BOOST
+01 / +02: Selects your preferred bass boost level. ; OFF: Cancels.
LOUD
01 / 02: Boosts low or high frequencies to produce a well-balanced
sound at low volume. ; OFF: Cancels.
SUB.W LEVEL *4
SPK-OUT *5
00 to +06 (+03): Adjusts the output level of the
subwoofer connected via speaker lead. ( 29)
PRE-OUT *6
–08 to +08 (00): Adjusts the output level of the
subwoofer connected to the lineout terminals (REAR/
SW) through an external amplifier. ( 29)
SUB.W *6
ON / OFF: Turns on or off the subwoofer output.
SUB.W LPF *4
THROUGH: All signals are sent to the subwoofer. ; LOW 55HZ /
MID 85HZ / HIGH 120HZ: Audio signals with frequencies lower than
55 Hz/ 85 Hz/ 120 Hz are sent to the subwoofer.
SUB.W PHASE *4
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [THROUGH] is selected for
[SUB.W LPF].)
FADER
R06 — F06 (00): Adjusts the front and rear speaker output balance.
BALANCE *7
L06 — R06 (00): Adjusts the left and right speaker output balance.
VOL ADJUST
–05 — +05 (00): Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOL ADJ FIX” appears if FM is selected.)
AMP GAIN
LOW POWER: Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50 W to prevent damaging
the speakers.) ; HIGH POWER: The maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression. ; OFF: Cancels.
SPK/PRE OUT
Selects the appropriate setting to get the desired output. (See the
following table.)
*4
*5
*6
*7
Displayed only when [SUB.W] is set to [ON].
Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W].
Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W].
This adjustment will not affect the subwoofer output.
SPK/PRE OUT
Connection via lineout terminals ( 29)
Lineout terminal
Setting
FRONT
REAR/SW
REAR/REAR
Front speakers output
Rear speakers output
REAR/SUB.W
Front speakers output
Subwoofer output
SUB.W/SUB.W
Front speakers output
Subwoofer output
Connection via speaker leads ( 29)
Rear speaker lead
Setting
L (left)
R (right)
REAR/REAR
Rear speakers output
Rear speakers output
REAR/SUB.W
Rear speakers output
Rear speakers output
SUB.W/SUB.W
Subwoofer output
(Mute)
If [SUB.W/SUB.W] is selected:
– [HIGH 120HZ] is selected in [SUB.W LPF] and [THROUGH] is not available.
– [R01] is selected in [FADER] and selectable range is [R06] to [00]
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 21
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
21
11/9/2014 4:57:59 PM
DISPLAY SETTINGS
1 Press and hold
.
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
BRIGHTNESS
Sets the button, display and USB input terminal brightness for day and night
separately.
1 DAY / NIGHT: Select day or night.
2 Select a zone for setting. ( Illustration on left)
3 Set the brightness level (00 to 31). (Default: DAY: 31 ; NIGHT: 15)
SCROLL *2
ONCE: Scrolls the display information once. ; AUTO: Repeats scrolling at
5-second intervals. ; OFF: Cancels.
*1 The illumination control wire connection is required. ( 29)
*2 Some characters or symbols will not be shown correctly (or will be blanked).
the instructions stated on the selected item.
to exit.
To return to the previous setting item, press
.
4 Press
Default: XX
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the [BRIGHTNESS]
setting.
OFF: Selects the day adjustments. ; ON: Selects the night adjustments. ;
DIMMER TIME: Adjusts the dimmer on and off time.
Turn the volume knob to adjust the [ON] time, then press the knob.
Turn the volume knob to adjust the [OFF] time, then press the knob.
(Default: [ON]: 18:00 or 6:00 PM
[OFF]: 6:00 or 6:00 AM)
AUTO: Changes between the day and night adjustments when you turn off or
on the car headlights. *1
22
JS_JVC_KD_X320BTS_J_EN_2.indd 22
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:58:00 PM
MORE INFORMATION
Playable files
• Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.m4a), WAV (.wav), FLAC (.flac)
• Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
About USB devices
• This unit can play MP3/WMA/AAC/WAV/FLAC files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- AAC Tag: 64 characters
- WAV Tag: 64 characters
- FLAC Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder
without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1 A.
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• It is not possible to browse video files on the “Videos” menu in [HEAD MODE].
• The song order displayed on the selection menu of this unit may differ from that of the iPod/
iPhone.
• If some operations are not performed correctly or as intended, visit:
<http://www.jvc.net/cs/car/>.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory
(AOA) 2.0.
• If the Android device supports both mass storage class device and AOA 2.0, this unit always
playback via AOA 2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>.
About Pandora
• Pandora is available only in the U.S., Australia and New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired, or some or all of the services may
become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at pandora-support@pandora.com.
About iHeartRadio
• iHeartRadio® is a third-party service, therefore the specifications are subject to change
without prior notice. Accordingly, compatibility may be impaired or some or all of the
services may become unavailable.
• Some iHeartRadio® functionality cannot be operated from this unit.
About Bluetooth
• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able
to connect to this unit.
• This unit may not work with some Bluetooth devices.
• Signal conditions vary, depending on the surroundings.
• For more information about Bluetooth, visit the following JVC website:
<http://www.jvc.net/cs/car/>.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 23
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
23
11/9/2014 4:58:00 PM
TROUBLESHOOTING
About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and AndroidTM application JVC Music
Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music
Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site:
<http://www.jvc.net/cs/car/>.
Symptom
Change the display information
Press
repeatedly.
Radio
Station name (PS)*1 Frequency Program type (PTY)*1*2
Title*1*2 Day/Clock (back to the beginning)
*1 For FM Radio Broadcast Data System stations only.
*2 If unavailable, “NO PTY” / “NO TEXT” appears.
USB
Playing time Day/Clock Album title/Artist*3
Folder/file name (back to the beginning)
*3 If not recorded, “NO NAME” appears.
Track title*3
USB-IPOD
USB-ANDROID
Playing time Day/Clock Album title/Artist*4
to the beginning)
*4 If not recorded, “NO NAME” appears.
Track title*4
PANDORA
Station name Album title/Artist
Clock (back to the beginning)
IHEART
Station name Track title*5 Track Artist*5
the beginning)
*5 If unavailable, station name appears.
SiriusXM
Channel no./Channel name B Artist B Song title B Content information
B Category name B Day/Clock B (back to the beginning)
AUX
AUX
BT AUDIO
Playing time Day/Clock Album title/Artist*6
to the beginning)
*6 If not recorded, “UNKNOWN” appears.
Track title
Playing time
Day/Clock
(back
Day/
(back to
Day/Clock
Track title*6
(back
• Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
Turn the power off, then check to be sure the terminals
of the speaker wires are insulated properly. Turn the
power on again.
“PROTECTING SEND
SERVICE” appears.
Send the unit to the nearest service center.
Source cannot be selected.
Check the [SRC SELECT] setting. ( 4)
• Connect the antenna firmly.
• Radio reception is poor.
• Static noise while listening • Pull the antenna out all the way.
to the radio.
Playback order is not as
intended.
The playback order is determined by the file name
(USB).
Elapsed playing time is not
correct.
This depends on the recording process earlier.
“NOT SUPPORT” appears and
file skips.
Check whether the file is a playable format. ( 23)
“READING” keeps flashing.
USB / iPod
FM or AM
Remedy
Sound cannot be heard.
General
MORE INFORMATION
• Do not use too many hierarchical levels and folders.
• Reattach the USB device.
“CANNOT PLAY” flashes and/ • Check whether the connected device is compatible with
or connected device cannot
this unit and ensure the files are in supported formats.
be detected.
( 23)
• Reattach the device.
The iPod/iPhone does not
turn on or does not work.
Correct characters are not
displayed.
• Check the connection between this unit and iPod/
iPhone.
• Detach and reset the iPod/iPhone using hard reset.
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
24
JS_JVC_KD_X320BTS_J_EN_2.indd 24
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:58:00 PM
TROUBLESHOOTING
Remedy
ANDROID
Cannot playback at
[AUTO MODE].
“NO DEVICE” or
“READING” keeps
flashing.
Playback is intermittent
or sound skips.
Pandora
“CANNOT PLAY”
Remedy
“UPGRADE APP”
Make sure you have installed the latest version of the
Pandora application on your device.
“CONNECT ERR”
Communication is unstable.
“RATING ERR”
Registration of thumbs up/thumbs down has failed.
“LICENSE ERR”
You try to access from a country which Pandora is not
deliverable.
• Make sure JVC MUSIC PLAY APP is installed on the Android
device. ( 5)
• Reconnect the Android device and select the appropriate
control mode. ( 6)
• If this does not solve the problem, the connected Android
device does not support [AUTO MODE]. ( 23)
Station cannot be selected.
If “Explicit Content” in [Account Settings] is checked in
the web version of iHeartRADIO, custom stations become
unavailable.
• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android
device does not support [AUTO MODE]. ( 23)
Turn off the power saving mode on the Android device.
• Make sure Android device contains playable audio files.
• Reconnect the Android device.
• Restart the Android device.
Pandora
• Sound cannot be heard • Reconnect the Android device.
during playback.
• If in [AUDIO MODE], launch any media player application
on the Android device and start playback.
• Sound output only
• If in [AUDIO MODE], relaunch the current media player
from the Android
application or use another media player application.
device.
• Restart the Android device.
• If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit. ( 23)
Symptom
iHeartRadio
Symptom
“CREATE ERR”
Custom station name creation is unsuccessful.
“SAVE ERROR”
Addition to the favorite category failed.
“DISCONNCTED”
Check the connection to the device.
“NO SKIPS”
The skip limit has been reached. Retry later.
“NO STATIONS”
No stations are found.
“NOT CONNCTD”
Link to the application is impossible.
“UPDATE APP”
Make sure you have installed the latest version of the
iHeart Link for JVC application on your device.
“PLS LOGIN”
You haven’t log in. Log in again.
“STATION NOT AVAILABLE”
Broadcast from the station is over.
“STATION NOT SELECTED”
No station is selected.
Check the Pandora application on your device.
“STREAM ERR”
Broadcast data is interrupted.
The skip limit has been reached.
“THUMBS ERR”
Registration of Thumbs Up/Down has failed.
“NO STATIONS”
No stations are found.
“TIMED OUT”
The request has resulted in time-out.
“STATION LMT”
The number of registered stations has reached its limit.
Retry after deleting unnecessary stations from your device.
“ADD ERROR”
“SEARCH ERR”
New station creation is unsuccessful.
“CHK DEVICE”
“NO SKIPS”
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 25
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
25
11/9/2014 4:58:01 PM
TROUBLESHOOTING
Bluetooth®
Remedy
“CH LOCKED LOCK
CODE?”
The selected channel is locked. Enter the correct pass code
to unlock. ( 13)
“CHAN UNSUB”
The selected channel is unsubscribed.
Call 1-866-635-2349 in U.S.A. or 1-877-438-9677 in Canada
to subscribe.
“CH UNAVAIL”
The selected channel is unavailable. Visit
www.siriusxm.com for more information about the
SiriusXM channel lineup.
“CHK ANTENNA”
Check the antenna and its connection are in good condition.
“CHECK TUNER”
Make sure the SiriusXM Vehicle Tuner is connected to the
unit.
“NO SIGNAL”
Make sure the antenna is mounted outside the vehicle.
“SUBSCRIPTION
UPDATED – PRESS
ENTER TO CONTINUE.”
Your subscription is updated. Press the volume knob to
continue.
“CODE ERROR”
Make sure you have entered the correct pass code. ( 13)
“NO CONTENT”
There is insufficient content to start TuneScan.
“SCAN CANCEL”
TuneScan has been aborted.
No Bluetooth device is
detected.
• Search from the Bluetooth device again.
• Reset the unit. ( 3)
Pairing cannot be
made.
• Make sure you have entered the same PIN code to both the
unit and Bluetooth device.
• Delete pairing information from both the unit and the
Bluetooth device, then perform pairing again. ( 14)
Echo or noise occurs.
• Adjust the microphone unit’s position. ( 14)
• Check the [ECHO CANCEL] setting. ( 15)
Phone sound quality
is poor.
• Reduce the distance between the unit and the Bluetooth
device.
• Move the car to a place where you can get a better signal
reception.
Symptom
Bluetooth®
SiriusXM® Radio
Symptom
Remedy
Sound is being
interrupted or skipped
during playback of a
Bluetooth audio player.
• Reduce the distance between the unit and the Bluetooth
audio player.
• Turn off, then turn on the unit and try to connect again.
• Other Bluetooth devices might be trying to connect to the
unit.
The connected
Bluetooth audio player
cannot be controlled.
• Check whether the connected Bluetooth audio player
supports Audio/Video Remote Control Profile (AVRCP).
(Refer to the instructions of your audio player.)
• Disconnect and connect the Bluetooth player again.
“PAIRING FULL”
The number of registered devices has reached its limit.
Retry after deleting an unnecessary device. ( 18,
DELETE PAIR)
“PLEASE WAIT”
The unit is preparing to use the Bluetooth function. If the
message does not disappear, turn off and turn on the
unit, then connect the device again.
“BT DEVICE NOT FOUND”
The unit failed to search for the registered Bluetooth
devices during [AUTO CNNCT]. Turn on Bluetooth from
your device and connect manually. ( 18)
“NOT SUPPORT”
The connected phone does not support Voice Recognition
feature.
“ERROR”
Try the operation again. If “ERROR” appears again, check
if the device supports the function you have tried.
“H/W ERROR”
Reset the unit and try the operation again. If “H/W
ERROR” appears again, consult your nearest service center.
“BT ERROR PLS UPDATE”
Update the Bluetooth firmware. ( 4)
If you have any troubles, try the following:
1 Check TROUBLESHOOTING
2 Reset the unit ( 3)
3 Contact (USA only)
Call: 1-800-252-5722 ( or ) visit: http://www.jvc.com
26
JS_JVC_KD_X320BTS_J_EN_2.indd 26
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:58:01 PM
8.2 dBf (0.71 μV/75 Ω)
Quieting Sensitivity (DIN S/N = 46 dB)
17.2 dBf (2.0 μV/75 Ω)
Frequency Response (±3 dB)
30 Hz — 15 kHz
Signal-to-Noise Ratio (MONO)
64 dB
AM Frequency Range
40 dB
530 kHz — 1 700 kHz (10 kHz step)
531 kHz — 1 611 kHz (9 kHz step)
Channel Space Selection
9 kHz/10 kHz
Usable Sensitivity (S/N = 20 dB)
29 dBμ (28.2 μV)
USB Standard
USB 1.1, USB 2.0 (Full speed)
Compatible Devices
Mass storage class
File System
FAT12/ 16/ 32
Maximum Supply Current
DC 5 V D/A Converter
24 Bit
Frequency Response (±1 dB)
20 Hz — 20 kHz
Signal-to-Noise Ratio (1 kHz)
105 dB
Dynamic Range
88 dB
Channel Separation
90 dB
MP3 Decode
Compliant with MPEG-1/2 Audio Layer-3
WMA Decode
Compliant with Windows Media Audio
AAC Decode
AAC-LC “.m4a” files
WAV Decode
RIFF waveform Audio Format (Linear
PCM only)
FLAC Decode
FLAC files
1 A
Bluetooth
50 kHz/200 kHz
Usable Sensitivity (S/N = 26 dB)
Audio
Channel Space Selection
Stereo Separation (1 kHz)
USB
87.9 MHz — 107.9 MHz (200 kHz step)
87.5 MHz — 108.0 MHz (50 kHz step)
General
Tuner
FM Frequency Range
Auxiliary SPECIFICATIONS
Frequency Response (±3 dB)
20 Hz — 20 kHz
Input Maximum Voltage
1 000 mV
Input Impedance
30 kΩ
Version
Bluetooth Ver.2.1+EDR/ Bluetooth 3.0
Frequency Range
2.402 GHz — 2.480 GHz
Output Power
+4 dBm (MAX), 0 dBm (AVE) Power Class 2
Maximum Communication Range
Line of sight approx. 10 m (32.8 ft)
Pairing
SSP (Secure Simple Pairing)
Profile
HFP1.6 (Hands-Free Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP1.4 (Audio/Video Remote Control Profile)
PBAP (Phonebook Access Profile)
SPP (Serial Port Profile)
Maximum Output Power
50 W × 4 or
50 W × 2 + 50 W × 1 (Subwoofer = 4 Ω)
Full Bandwidth Power
(at less than 1 % THD)
22 W × 4
Speaker Impedance
4 Ω — 8 Ω
Preout Level/Load (USB)
2 500 mV/10 kΩ
Preout Impedance
≤ 600 Ω
Operating Voltage
(10.5 V — 16 V allowable)
14.4 V
Maximum Current Consumption
10 A
Operating Temperature Range
0°C to +40°C
Installation Size (W × H × D)
182 mm × 53 mm × 108 mm
(7-3/16" × 2-1/8" × 4-5/16")
Weight
0.60 kg (1.4 lbs)
Subject to change without notice.
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 27
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
27
11/9/2014 4:58:02 PM
INSTALLATION / CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Installing the unit (in-dash mounting)
Do the required wiring.
( 29)
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50 W. If the
maximum power of the speakers is lower than 50 W, change the
[AMP GAIN] setting to avoid damaging the speakers. ( 21)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then
disconnect the
Hook on the top side
Orientate the trim plate as
illustrated before fitting.
Dashboard of
your car
Bend the appropriate tabs to
hold the sleeve firmly in place.
When installing without the mounting
sleeve
How to remove the unit
Use only the specified screws. Using wrong screws
might damage the unit.
Flat or round head screws
(not supplied)
M5 × 8 mm (M5 × 3/8")
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( 29)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Reset the unit. ( 3)
Pocket
Bracket (not supplied)
28
JS_JVC_KD_X320BTS_J_EN_2.indd 28
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
11/9/2014 4:58:02 PM
Wiring connection
Signal cord (not supplied)
Front output
JVC Amplifier *1
Rear/subwoofer output
Remote wire
(not supplied)
(B) Trim plate
To the optional SiriusXM Vehicle Tuner
(commercially available) ( 11)
Light blue/yellow
STEERING
WHEEL
REMOTE
Blue/white: Remote (200 mA max.)
Orange/white: Illumination
Factory wiring
harness (vehicle)
To the steering wheel
remote control adapter
(Not used)
Separate red wire
Make this connection if
your vehicle factory wiring
harness does not have
“12 V ignition switch” wire.
*2 You can also connect a
subwoofer speaker directly
using this lead without an
external subwoofer amplifier.
For setting, 21.
(C) Mounting sleeve
Recommended
connection
Blue: To power antenna
Blue/white: To amplifier
Brown
Yellow: Battery 12 V
Car fuse block
(A) Faceplate
Antenna terminal
Join the same color wires together.
Ignition switch
Part list for
installation
Vehicle dashboard
Fuse (10 A)
MIC (Microphone
input terminal)
( 14)
*1 Firmly connect the ground wire of
the amplifier to the car’s chassis to
avoid damaging the unit.
Vehicle-specific Wiring
Harness (separately
purchased)
(D) Wiring harness
Red: Ignition 12 V
Black: Ground
Gray: Front speaker (right)
Gray/black
White: Front speaker (left)
White/black
Purple: Rear speaker (right)
Purple/black
Green: Rear speaker (left) *2
Green/black *2
For more information:
Metra Electronics:
www.metraonline.com
Scosche Industries:
www.scosche.com
(E) Extraction key
ENGLISH
JS_JVC_KD_X320BTS_J_EN_2.indd 29
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
29
11/9/2014 4:58:02 PM