Milli Axon Wall Top Assemblies | Reece Bathrooms

page 1 of 3
42
MILLI AXON
WALL TOP ASSEMBLIES
6
55
14
57
SPECIFICATIONS
Recommended Use
Domestic, hotel and commercial
Finish Available
Chrome Handle with Chrome B/P
Chrome/Black Handle with Chrome B/P
Chrome/Black Handle with Black B/P
Pressure Rating
Maximum continous operating pressure 500 kPa.
Note: For best performance and longer life we
recommend 150-500 kPa.
Temperature Rating
Maximum continous working temperature 75o
Suitable Hot Water
Storage Tank: No
Continuous Flow: Refer to manufacturer of
continuous hot water systems
Gravity Feed: No
Standards
AS/NZS 3718
To see the complete Milli range go to
www.reece.com.au/bathrooms
CLEANING RECOMMENDATIONS
This product should not be cleaned with abrasive materials eg. steel
wool/scourers. Damage caused by any improper treatment is not
covered by the product warranty - refer to Warranty Conditions on the
last page.
Disclaimer: Products in this specification manual must by regulation be installed by licensed and
registered trade people. The manufacturer/distributor reserves the right to vary specifications or
delete models from their range without prior notification. Dimensions are nominal measurements only.
Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor
takes no responsibility for printing errors.
Tech Page Version 1
Brand logo area
- grey box to be
deleted. Apply on
Master Page
page 2 of 3
MILLI AXON
WALL TOP ASSEMBLIES
INSTALLATION INSTRUCTIONS
Milli Axon Wall Top Assemblies INSTALLATION INSTRUCTIONS
WATER SUPPLY REQUIREMENTS
Breach are in good
condition and are free
of foreign objects.
75
Recommended Working
Pressure
Maximum hot water
temperature
Note:
-If the pressure exceeds or is likely to
exceed 550kpa, an approved pressure
limiting device must be installed.
- Flush out all pipe work prior to
installation.
- If the water temperature exceeds 75°C,
an approved tempering valve must be
fitted.
- Installation should comply with
Australian standard AS3500.1 or
relevant local authority requirements.
Recessed Breach to Wall
Surface. Check against
diagram below to determine
which cartridge extension
to be used in step 4.
Wall Surface
Max. 17mm
Recommended
installation range for
Recessed Breach
as shown in diagram.
150 KPa Min.
550 KPa Max.
3 Screw Cartridge into Recess until Cartridge
2 Measure the distance from
1 Check seats in Recessed
seals with seat in Recess.
Do not over-tighten
Distance
Cartridge
0mm~12mm
Reseat if required.
18mm
12mm~17mm
29mm
Recessed Breach
4 Fit the cartridge extension onto the
cartridge spindle.
Fasten screw.
5 Fit Red Fibre Washer around the cartridge.
Fasten Bonnet onto the cartridge firmly with
a spanner.
Failure to comply with the above may
void all warranties.
Bonnet
Screw
Maintenance and Care
-Chrome plated surfaces should be
cleaned with mild liquid detergent or
soap and water.
-Do not use cream cleaners or citrus
based cleaning products, as they are
abrasive.
-Use of unsuitable cleaning agents may
damage the surface. Any damage
caused in this way will not be covered
by warranty.
Cartridge
Extension
Red Fibre
Washer
Turn the cartridge clockwise untill it stops at
the “OFF” position.
OFF
OFF
Place Square Plate into position.
Fasten Lock Nut to secure Square Plate.
Lock
Nut
8 Fit Nylon Washer into the groove of Lock Nut.
Mixer Operation
6 Fit “O” Ring to Square Plate.
Square Plate
“O” Ring
9 Push on Handle over the cartridge extension.
Fasten Grub Screw firmly, push in Screw Cap.
Nylon Washer
Nylon Washer
3/4 Turn
Handle
3/4 Turn
Screw Cap
NOTE : The handle with hot marking must be on the left
IN0187_revA
Grub Screw
hand side as viewed from the users position.
Plumbers, please ensure a copy of the installation instructions
is left with the end user for future reference
Brand logo area
- grey box to be
deleted. Apply on
Master Page
QU
AL
7
YEAR
IT Y
TE
MILLI AXON
WALL TOP ASSEMBLIES
E
page 3 of 3
G UARA
N
REECE PRODUCT QUALITY GUARANTEE
You have purchased a quality product from Reece Pty Ltd
ABN 84 004 097 090 (“Reece”). This product is covered by a
7 year replacement product warranty and a 12 month warranty
over spare parts and labour.
This warranty does not include faults caused by:
7 YEAR WARRANTY – DOMESTIC USE
This warranty covers faults in the product construction, material
and assembly. Products which are within 7 years from the
date of purchase, found upon inspection by an authorised
Reece representative, to be defective in construction, material
or assembly, will be repaired or exchanged with an equivalent
product free of charge. Replaced items become Reece’s
property. This warranty also covers any spare parts included
under “Manufacturer’s Provisions” below.
• Installation or part installation by the purchaser or any person
other than a LICENSED PLUMBER
All replacement products will be available for collection without
charge to the customer at the nearest Reece branch to the
customer’s location, or elsewhere as agreed between the
customer and Reece.
Labour and Spare Parts
The labour for the replacement of products and spare parts
to which this warranty applies will be supplied by Reece or
relevant supplier using licensed plumbers engaged by Reece or
relevant supplier within 1 year from the date of purchase.
Spare parts other than those listed in the Manufacturer’s
Provisions above, which are within 1 year from the date of
purchase found upon inspection by an authorised Reece
representative to be defective in construction, material or
assembly, will be replaced free of charge.
Warranty Conditions
This warranty will apply only under all of the
following conditions:
• The item has been installed by a licensed plumber
• The item has been installed for and subjected to domestic
residential use only
• Failure is due to a fault in the manufacture of the product
• Proof of purchase (including the date of purchase)
is provided
• The installation of the product is in accordance with the
instructions provided
• Incorrect installation or installation not in accordance with
the instructions provided
• Normal wear and tear
• Inadequate or complete lack of maintenance
• Chemical, electrochemical or electrical influences
• Harsh detergents or abrasive cleaners used on
product finishes
1 YEAR WARRANTY – COMMERCIAL USE
‘Commercial’ use is all use other than for normal domestic
residential purposes, including use in non-business places as in
public buildings, schools, sports centres and in establishments
that contain private bathrooms with high frequency of use by
many individuals, such as hotels, motels, retirement villages
and hospitals.
The Commercial warranty covers this product against
manufacturing faults in the construction, material and assembly
of both the finished products and any spare parts for a period
of 1 year from the date of purchase. Products and spare
parts which are found upon inspection by an authorised
Reece representative to be defective in construction, material
or assembly will be repaired or exchanged free of charge.
Replaced items become Reece’s property. The labour for the
replacement of products and spare parts to which this warranty
applies will be supplied by Reece or relevant supplier using
licensed plumbers engaged by Reece or relevant supplier.
The Warranty Conditions and exclusions which apply to the
domestic use warranty also apply to this commercial warranty.
EXCLUSIONS
To the fullest extent permitted by law, Reece excludes all liability
for damage or injury to any person, damage to any property,
and any indirect consequential or other loss or damage.
CLAIM PROCEDURE
For all warranty queries customers are to contact the branch
where the product was purchased. These details can be found
on your purchase invoice.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
TAP.T1.7YR
This warranty does not cover products purchased as an
ex-display without being fully checked and tested for sale by
the manufacturer.
• Unsuitable or improper use
Don’t risk it, use a licensed plumber.™
Brand logo area
- grey box to be
deleted. Apply on
Master Page