Operating and installation instructions Cooker hood

Operating and installation instructions
Cooker hood
To prevent the risk of accidents or damage to the appliance, it is
essential to read these instructions before it is installed and used for
the first time.
en-SA, AE
M.-Nr. 10 650 890
Contents
Warning and Safety instructions.......................................................................... 4
Caring for the environment ................................................................................ 13
Guide to the appliance ........................................................................................ 14
Modes of operation ............................................................................................. 16
Operation.............................................................................................................. 17
To switch the fan on .............................................................................................. 17
To select a power level .......................................................................................... 17
To switch the fan off .............................................................................................. 17
Switching the hob lighting on/off .......................................................................... 17
Power management .............................................................................................. 17
Switching Power management on/off .............................................................. 18
Safety switch-off ................................................................................................... 18
Energy saving tips ............................................................................................... 19
Cleaning and care ............................................................................................... 20
Housing ................................................................................................................. 20
Grease filters ......................................................................................................... 21
Charcoal filter ........................................................................................................ 23
Disposing of charcoal filters ............................................................................. 23
Reactivatable charcoal filter ............................................................................. 23
Changing a lamp ................................................................................................... 24
Installation............................................................................................................ 25
Before installation.................................................................................................. 25
Protective foil......................................................................................................... 25
Installation instructions.......................................................................................... 25
Dismantling............................................................................................................ 25
Assembly parts...................................................................................................... 26
Appliance dimensions ........................................................................................... 28
Safety distance between hob and cooker hood (S) .............................................. 29
Installation recommendations ............................................................................... 30
Drilling diagram for wall mounting......................................................................... 30
Connection for air extraction ............................................................................. 31
Condensate trap.................................................................................................... 32
Silencer.................................................................................................................. 32
Electrical connection .......................................................................................... 34
Electrical connection ............................................................................................. 34
2
Contents
After Sales / Guarantee....................................................................................... 35
Position of the data plate ...................................................................................... 35
Technical data...................................................................................................... 36
3
Warning and Safety instructions
This appliance complies with all relevant local and national safety
requirements. Inappropriate use can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and damage to the appliance, please
read these instructions carefully before using it for the first time.
They contain important notes on the safety, installation, use and
maintenance of the appliance. Miele cannot be held liable for noncompliance with these instructions.
Keep these instructions in a safe place and ensure that all users
are familiar with the contents. Pass them on to any future owner of
the appliance.
Correct application
 This cooker hood is intended for use in domestic households and
similar working and residential environments.
 The cooker hood is not intended for outdoor use.
 It must only be used as a domestic appliance to extract vapours
and remove odours from cooking.
Any other usage is not supported by the manufacturer and could be
dangerous.
 Where a recirculation cooker hood is fitted above a gas hob,
please ensure that there is an adequate supply of fresh air into the
room in which it is installed. Please seek the advice of a qualified gas
fitter if necessary.
4
Warning and Safety instructions
 The cooker hood can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and recognise and understand the
consequences of incorrect operation.
Safety with children
 Children under 8 years of age must be kept away from the cooker
hood unless they are constantly supervised.
 Children 8 years and older may only use the cooker hood
unsupervised if they have been shown how to use it safely and
recognise and understand the consequences of incorrect operation.
 Children must not be allowed to clean or maintain the cooker
hood unsupervised.
 Please supervise children in the vicinity of the cooker hood and do
not let them play with it.
 The hob lighting is very intensive.
Ensure, in particular, that babies/small children do not look at the
light.
 Danger of suffocation. Packaging, e.g. plastic wrappings, must be
kept out of the reach of babies and children. Whilst playing, children
could become entangled in packaging or pull it over their head and
suffocate.
5
Warning and Safety instructions
Technical safety
 Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and
repairs must only be carried out by a Miele authorised technician.
 A damaged appliance can be dangerous. Check it for visible signs
of damage. Do not use a damaged appliance.
 The electrical safety of this appliance can only be guaranteed
when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt please have the electrical
installation tested by a qualified electrician.
 Reliable and safe operation of this cooker hood can only be
assured if it has been connected to the mains electricity supply.
 Before connecting the appliance to the mains supply, ensure that
the connection data on the data plate (voltage and frequency) match
the mains electricity supply. This data must correspond in order to
avoid the risk of damage to the appliance. Consult a qualified
electrician if in any doubt.
 Do not connect the appliance to the mains electricity supply by a
multi-socket unit or an extension lead. These are a fire hazard and
do not guarantee the required safety of the appliance.
6
Warning and Safety instructions
 For safety reasons, this appliance may only be used after it has
been built in.
 The cooker hood must not be used in a non-stationary location
(e.g. on a ship).
 Touching electrical components and tampering with electrical and
mechanical parts is highly dangerous to the user and can cause
operational faults.
Only open the housing as described in the instructions given in the
installation sheet and in the Cleaning and care section of this
booklet. Under no circumstances should any other parts of the
housing be opened.
 The manufacturer's warranty will be invalidated if the appliance is
not repaired by a Miele approved service technician.
 Miele can only guarantee the safety of the appliance when
genuine original Miele replacement parts are used. Faulty
components must only be replaced by Miele spare parts.
 If the electrical connection cable is faulty it must only be replaced
by a Miele authorised service technician to protect the user from
danger.
 During installation, maintenance and repair work, the appliance
must be disconnected from the mains electricity supply.
7
Warning and Safety instructions
Using at the same time as other heating appliances that depend on the air
from the room
 Warning - danger of toxic fumes
Great care should be taken when using the cooker hood at the
same time and in the same room or area of the house as another
heating appliance which depends on the air in the room.
Such appliances include gas, oil, wood or coal-fired boilers and
heaters, continuous flow or other water heaters, gas hobs,
cookers or ovens which draw air in from the room and duct
exhaust gases out through a chimney or extraction ducting.
When used in extraction mode, with or without an external motor
fitted, or in recirculation mode with a recirculation box installed
outside the room, the appliance draws air in from the room in
which it is installed and from neighbouring rooms.
If there is insufficient air, an underpressure will occur. The heating
appliance will be starved of oxygen, impairing combustion.
Harmful gases could be drawn out of the chimney or extraction
ducting back into the room, with potentially fatal consequences.
8
Warning and Safety instructions
In order to ensure safe operation, and to prevent gases given off
by the heating appliances from being drawn back into the room
when the cooker hood and the heater are in operation
simultaneously, an underpressure in the room of 0.04 mbar (4 pa)
is the maximum permissible.
Ventilation can be maintained by air inlets which cannot be
blocked, in windows, doors or outside wall vents, or by other
technical measures, such as ensuring that the cooker hood can
only be switched on when the heating appliance is switched off or
vice versa. A ventilation brick alone is not generally sufficient to
ensure safe ventilation.
The overall ventilation condition of the dwelling must be taken into
account. If in any doubt, the advice of a competent builder or, for
gas a qualified gas fitter (registered with an official gas safety body
in accordance with national safety regulations) must be sought.
If the cooker hood is used in recirculation mode, where the air is
directed back into the room in which it is located, operating a
heating appliance which depends on the room air at the same time
is no cause for concern.
9
Warning and Safety instructions
Correct use
 Never use a naked flame beneath the cooker hood. To avoid the
danger of fire, do not flambé or grill over a naked flame.
When switched on, the cooker hood could draw flames into the filter.
Fat deposits could ignite, presenting a fire hazard.
 The cooker hood can become damaged when exposed to
excessive heat.
– When using the cooker hood over a gas hob, ensure that any
burners in use are always covered by a pan. Switch the cooking
zone off when a pan is removed, even for a short time.
– Select a pan which is suitable for the size of the burner.
– Regulate the flame so that it does not burn up the sides of the
pan.
– Avoid overheating the pan (e.g. when cooking with a wok).
 Always switch the cooker hood on when a cooking zone is in use,
otherwise condensation may collect in the hood, which could cause
corrosion.
 When cooking with oil or fat, chip pans and deep fat fryers etc, do
not leave the pans unattended. Never leave an open grill unattended
when grilling. Overheated oil and fat can ignite and could set the
cooker hood on fire.
10
Warning and Safety instructions
 Do not use the cooker hood without the filters in place. This way
you will avoid the risk of grease and dirt getting into the appliance
and hindering its smooth operation.
 There is a risk of fire if the cooker hood is not cleaned as
described in these operating instructions.
 The cooker hood can get very hot during cooking due to heat
rising from the hob.
Do not touch the housing or the grease filters until the cooker hood
has cooled down.
 This cooker hood is not suitable for placing objects on.
Correct installation
 Refer to the cooker or hob manufacturer's instructions as to
whether a cooker hood may be operated above the cooker/hob.
 Safety regulations prohibit the fitting of a cooker hood over solid
fuel stoves.
 Insufficient distance between the cooker or hob and the cooker
hood can result in damage to the hood.
The minimum safety distances between the top of the cooker or hob
and the bottom of the cooker hood given in the "Installation" section
must be maintained, unless the hob manufacturer states that a
greater distance is required.
If more than one cooking appliance is fitted beneath the cooker
hood, and they have different minimum safety distances to the
cooker hood, select the greater distance.
 The distances given in "Installation" must be observed when
fitting the cooker hood.
11
Warning and Safety instructions
 Exhaust ducting must be of non-inflammable material. Suitable
material is available from your Miele dealer.
 The appliance must not be connected to a chimney or flue which
is in use. Neither should it be connected to ducting which ventilates
rooms with fireplaces.
 If exhaust air is to be extracted into a chimney or ventilation duct
no longer used for other purposes, seek professional advice.
Cleaning and care
 Do not use a steam cleaning appliance to clean this appliance.
The steam could reach electrical components and cause a short
circuit.
Accessories
 Only use genuine original Miele accessories and spare parts with
this appliance. Using accessories or spare parts from other
manufacturers will invalidate the guarantee, and Miele cannot accept
liability.
12
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Disposal of your old appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Miele dealer for
advice.
Ensure that it presents no danger to
children while being stored for disposal.
13
Guide to the appliance
14
Guide to the appliance
a Telescopic extension piece
b Tower
c Canopy
d Controls
e Grease filter(s) *
f Recirculation grilles
(only for recirculation mode)
g Hob lighting
h Charcoal filter
(special accessory for recirculation mode)
i On/Off control for the fan
j Controls to select the fan power level
k On/Off control for the hob lighting
*Your cooker hood is supplied with one or more grease filters depending on model.
Filters are referred to in the plural thoughout this booklet.
15
Modes of operation
Depending on the model of the cooker
hood, the following options are
available:
Extraction mode
The air is drawn in and cleaned by the
grease filters and directed outside.
Non-return flap
The non-return flap is designed to
prevent the exchange of room and
outside air taking place when the
cooker hood is switched off.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
If the on-site ventilation system does
not have a non-return flap, the nonreturn flap supplied must be fitted in the
exhaust socket in the motor unit.
16
Recirculation mode
(recirculation mode cooker hoods
require a conversion kit and charcoal
filter (available as optional accessories):
see "Technical Data")
The air is drawn in and cleaned first by
the grease filters and then by a charcoal
filter. The cleaned air is then
recirculated back into the kitchen.
Operation
To switch the fan on
 Press the On/Off control .
Switching the hob lighting on/
off
The fan will switch on at level 2. The 
symbol and 2 will light up in the power
level display.
The hob lighting can be switched on
and off independently of the fan.
To select a power level
The  symbol will light up when the
hob lighting is switched on.
For light to heavy cooking vapours and
odours, select from power levels 1 to 3.
For short periods of cooking food with
intensive vapours and a strong aroma,
e.g. when searing meat, select Booster
setting B.
 For a lower power level, press the
"" control, or "" for a higher level.
Reducing power down from the
Booster setting
If power management is activated
(default setting), the fan automatically
switches back to level 3 after 5 minutes.
To switch the fan off
 Use the On/Off control  to switch
the fan off.
 To do this, press .
Power management
The cooker hood features a power
management system to help save
energy. The fan power level is reduced
and the lighting is switched off
automatically.
– If the Booster setting has been
selected, the fan will automatically
switch to level 3 after 5 minutes.
– From levels 3, 2 or 1 the power will
be reduced by one level after 2 hours
and then in 30 minutes stages until
the fan finally switches off.
– The hob lighting will switch off
automatically after 12 hours.
The  symbol will go out.
17
Operation
Switching Power management on/off
Safety switch-off
You can deactivate Power
management.
This can result in increased electricity
consumption.
If Power management has been
deactivated, the cooker will switch itself
off automatically after 12 hours if it has
been left on (fan and hob lighting).
 To set this option, both the fan and
the hob lighting must be switched off.
 Pressing the On/Off control  or the
lighting control  will switch the fan
back on again.
 Press the "" and "" controls at the
same time for approx. 10 seconds,
until the 1 lights up.
 Then press in turn,
– the lighting control ,
– the "" button and then
– the lighting control  again.
If Power management is switched on,
the 1 and B indicators will light up
constantly.
If it is switched off, 1 and B will flash.
 Press "" to switch Power
management off.
The 1 and B indicators will flash.
 To switch it on, press "".
The 1 and B indicators will light up
constantly.
 Confirm your choice with the On/Off
control .
All the indicator lamps will go out.
If you do not confirm within 4 minutes,
the cooker hood will revert to the old
setting.
18
Energy saving tips
This cooker hood operates very
efficiently and economically. The
following will help you to save even
more energy when using it:
– Ensure that there is sufficient
ventilation in the kitchen when
cooking. In extraction mode, if there
is insufficient air flow the cooker
hood cannot operate efficiently and
this causes increased operating noise
levels.
– Always cook with the lowest possible
setting. This produces fewer cooking
vapours, so you can use a lower
cooker hood power level and
therefore benefit from reduced
energy consumption.
– Check the power level selected on
the cooker hood. A lower power level
is generally sufficient for the majority
of cooking. Only use the Booster
setting when necessary.
– When a large volume of cooking
vapours is being produced, switch to
a high power level in good time. This
is more efficient than operating the
cooker hood for longer to try to
capture cooking vapours which have
already been distributed throughout
the kitchen.
– Make sure that you switch the cooker
hood off after use.
– Clean or change the filters at regular
intervals. Heavily soiled filters reduce
performance, increase the risk of fire
and are unhygienic.
19
Cleaning and care
Housing
General information
The surfaces and controls are
susceptible to scratches and
abrasion.
Please observe the following
cleaning instructions.
 All external surfaces and controls can
be cleaned using hot water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
Important for appliances with
stainless steel surfaces
(This information does not apply to the
controls).
 Stainless steel surfaces can be
cleaned with a proprietary nonabrasive cleaning agent designed
specifically for use on stainless steel.
 To help prevent re-soiling, a
proprietary conditioning agent for
stainless steel (available from Miele)
can also be used.
Apply sparingly with a soft cloth.
Make sure that water does not get
into the cooker hood.
Only clean the area of the controls
with a damp cloth.
Important for RAL coloured housing
 Then wipe the surfaces dry using a
soft cloth.
It is very difficult to clean this type of
surface without causing minor marks
to the surface material. This can
become particularly noticeable
depending on the type of lighting in
the kitchen.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents.
20
(Special order finish)
 Please observe the general notes on
cleaning earlier in this section.
Cleaning and care
Important for the controls
Do not leave soiling on the controls
for any length of time.
Otherwise they may suffer
discolouration or damage.
Remove soiling straight away.
 Please observe the general notes on
cleaning earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
Grease filters
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
cooker hood.
 An oversaturated filter is a fire
hazard.
Cleaning interval
Grease which builds up over time will
harden and make cleaning more
difficult. The grease filters should be
cleaned regularly (at least every 3 - 4
weeks) to avoid a build-up of grease.
Removing a grease filter
When handling a grease filter, be
careful not to drop it.
This can result in damage to the filter
and the hob below.
Make sure you hold the filter securely
at all times when handling it.
 To take out a grease filter, release the
locking clip on the filter, lower the
filter approx. 45°, unhook it at the
back and remove it.
21
Cleaning and care
Cleaning the grease filters by hand
After cleaning
 Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid. Do not use "neat" washing up
liquid.
 After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
Unsuitable cleaning agents
Unsuitable cleaning agents can cause
damage to the surface of the filters if
used regularly.
Do not use:
– cleaning agents containing descaling
agents
 When removing the filters for
cleaning, also clean off any residues
of oil or fat from the now accessible
housing to prevent the risk of these
catching fire.
 Replace the grease filters, making
sure that the locking clips are facing
down towards the hob.
– powder cleaners, cream cleaners
– aggressive multi-purpose cleaning
agents or spray cleaners for grease
– oven sprays
Cleaning the grease filters in the
dishwasher
 Place the filters as upright as possible
in the lower basket, with the short
sides upright, ensuring the spray arm
is not obstructed.
 Use a standard household
dishwasher detergent.
 Select a dishwasher programme with
a wash temperature between 50°C
and 65°C.
Depending on the dishwasher
detergent used, cleaning the filter in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filter in any way.
22
 If a grease filter is inadvertently
replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.
Cleaning and care
Charcoal filter
When to change the charcoal filter
If the cooker hood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filters.
This is designed to absorb cooking
odours and is fitted in the canopy
above the grease filters.
 Always replace the charcoal filter
when it no longer absorbs kitchen
odours effectively.
It should, however be replaced at
least every 6 months.
Fitting/replacing a charcoal filter
 Used charcoal filters can be disposed
of with the normal household waste.
 Before fitting or replacing a charcoal
filter, the grease filters must first be
taken out (see previous section for
instructions on how to do this).
 Take the charcoal filter out of its
packaging.
Disposing of charcoal filters
Reactivatable charcoal filter
A reactivatable charcoal filter is
available for this cooker hood. By
reactivating it in an oven it can be
reused several times.
 It is supplied with its own installation
and usage instructions which must
be observed.
Charcoal filters are available to order
from your Miele dealer (see end of this
booklet for contact details).
 Press the charcoal filter into the
frame.
The charcoal filters are listed under
"Technical data" at the back of this
booklet.
 Replace the grease filters.
23
Cleaning and care
Changing a lamp
Only use the specified lamps.
Other lamps, e.g. halogen lamps,
may become damaged due to the
high generation of heat.
The lamps should be replaced with a
lamp of the same type:
 Switch off the fan and the lighting.
The lamps can get hot in use.
Allow the lamps to cool down for a
few minutes before changing them.
 Disconnect the cooker hood from the
mains electrical supply (see "Warning
and Safety instructions").
Manufacturer ............................... EGLO
Lamp type .................................... GU10
Specification................................ 11427
Wattage ........................................... 3 W
ILCOS D Code...... DR-3-H-GU10-50/56
Alternatively the following lamps can be
used:
Manufacturer ............................... EGLO
Lamp type .................................... GU10
Specification................................ 11511
Wattage ........................................... 5 W
ILCOS D Code...... DR-5-H-GU10-50/54
These lamps have a different luminosity.
Only use lamps of the same type in the
cooker hood.
These lamps are available from your
Miele dealer.
24
 Insert the lever supplied into the gap
between the lamp and the lamp
holder.
The lamp will then drop downwards.
 Grip the lamp, turn it anti-clockwise
and take it out.
 Screw the new lamp into the socket
and push it upwards. Please follow
the manufacturer's safety
instructions.
Installation
Before installation
 Before installation, it is important
to read the information given on the
following pages as well as the
"Warning and Safety instructions" at
the beginning of this booklet.
Protective foil
The housing components have
protective foil around them to protect
them from transport damage.
Dismantling
Should the appliance ever need to be
dismantled, follow the installation
instructions in reverse order as
described on the installation sheet. A
lever is supplied to assist with the
removal of the tower.
 Unscrew the two fixing screws on the
tower.
 Please remove this foil before fitting
the housing components. It can be
peeled off easily.
Installation instructions
See enclosed Installation sheet for
instructions on how to install this
appliance.
 Push the lever between the tower and
the extension piece.
 Lever the tower out of its fixings.
25
Installation
Assembly parts
26
Installation
a 3 protective sheets
for use when fitting the tower.
b 1 exhaust socket
for exhaust ducting  150 mm.
2 x M 6 self-tapping nuts
for securing the canopy
c 1 reducing collar
for exhaust ducting  125 mm.
d 1 non-return flap
for installation in the exhaust socket
of the motor unit (not for
recirculation mode). The non-return
flap may already be fitted depending
on model.
2 screws 3.9 x 7.5 mm
for securing the tower.
Keep the following in a safe place:
e
ntag tallation aje
gio
nt
Ins
Mo Montag ntering agem
s
nt
Mo
Mo Asennu
Mo
e Wall brackets
for securing the cooker hood to the
wall.
f Conversion kit for recirculation
mode
including directional unit, aluminium
hose and hose clips (the conversion
kit is not supplied. It has to be
purchased separately - see
"Technical data" for model number).
Installation instructions
1 lever
for replacing lamps and for dismantling
the tower.
8 screws, 5 x 60 mm and
8 plugs, 8 x 50 mm
for securing to the wall.
The screws and plugs are designed
for use in solid walls only.
For other types of wall construction,
alternative fixings will be required.
Make sure the wall is able to take the
weight of the cooker hood.
27
Installation
Appliance dimensions
The diagram is not drawn to scale.
28
Installation
a Extraction
b Recirculation
c Ventilation grille positioned at the top for recirculation
de (Only d is required for recirculation mode cooker hoods). The shaded area
represents the wall or ceiling area for the ducting cut-out and for the
connection socket. Recirculation cooker hoods only need a connection
socket to be fitted.
Connection for air extraction  150 mm, or 125 mm with reducing collar.
Safety distance between hob and cooker hood (S)
When planning the installation height of your cooker hood, the minimum safety
distance between the top of a cooker or hob and the bottom of the cooker hood
is as follows, unless a greater distance is specified by the manufacturer of your
cooking appliance.
See "Warning and Safety" instructions for further information.
Cooking appliance
Minimum distance S
Electric hob
450 mm
Electric grill, deep fat fryer (electric)
650 mm
Multi-burner gas hob,
total output ≤ 12.6 kW, no burner > 4.5 kW
650 mm
Multi-burner gas hob,
total output > 12.6 kW and ≤ 21.6 kW,
no burner > 4.8 kW.
760 mm
Multi-burner gas hob,
total output > 21.6 kW,
or multi-burner gas hob where one burner > 4.8 kW.
Not possible
Single burner gas hob, output ≤ 6 kW.
650 mm
Single burner gas hob, output > 6 kW and ≤ 8.1 kW.
760 mm
Single burner gas hob, output > 8.1 kW
Not possible
29
Installation
Installation recommendations
Drilling diagram for wall
– When deciding on the safety distance mounting
between the hob and cooker hood,
please note that a distance of 650
mm above electric cookers/hobs may
be preferable to give more working
space under the hood.
 Please follow the directions given in
the installation instructions supplied
for drilling.
– Account should also be taken of the
height of the person who will be
using the hood most often. They
should have sufficient space to work
comfortably at the hob, and be able
to reach the hood controls with ease.
– Please be aware that if positioned too
high, extraction will be inefficient.
– To achieve optimum vapour
extraction, the cooker hood must be
positioned centrally over the hob, not
to the side.
– The hob should be no wider than the
cooker hood, and if possible, it
should be narrower.
– The installation area must be easily
accessible. The cooker hood should
be easily accessible and easy to
dismantle in the event that service is
required. This should be taken into
consideration when planning the
position of cupboards, shelves,
ceilings or features in the vicinity of
the cooker hood.
 For pre-installation of a back wall
where the holes have to be predrilled, please refer to the drilling
distances in the drawing above
(screws  5 mm).
*The dimension for the middle wall
bracket is variable. It will depend on the
position of the wall vent and the socket.
It should be set as low as possible.
30
Connection for air extraction
 If the cooker hood is used at the
same time as a heating appliance
that relies on oxygen from the same
room, there is a risk in certain
circumstances of toxic fumes
building up.
It is essential that the "Warning and
Safety" instructions are observed.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
Use smooth or flexible ducting made
from approved non-flammable
materials for exhaust ducting.
To achieve the most efficient air
extraction with the lowest noise levels,
please note the following:
– The diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the cross
section must not be smaller than the
cross sectional area of the exhaust
connection.
– The exhaust ducting should be as
short and straight as possible.
 If the exhaust is ducted through an
outside wall, a telescopic wall vent or
a roof vent (available as an optional
accessory) is recommended.
 If the exhaust air is to be ducted into
a flue, the ducting must be directed in
the flow direction of the flue.
 When ducting is horizontal it must be
laid to slope away at at least 1 cm per
metre. This is to ensure that
condensate cannot drain back into
the appliance.
 If the exhaust ducting is to run
through rooms, ceiling space etc.
where there may be great variations
in temperature between the different
areas, the problem of condensation
will need to be addressed. The
exhaust ducting will need to be
suitably insulated.
– Only use wide radius bends.
– The exhaust duct must not be kinked
or compressed.
– Ensure that all connections are
strong and airtight.
Remember that any constriction of
the air flow will reduce extraction
performance and increase operating
noise.
31
Connection for air extraction
Condensate trap
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur.
Condensate traps for 125 mm or 150
mm ducting are available as optional
accessories.
 When installing a condensate trap,
ensure that it is positioned vertically
and as closely as possible above the
exhaust socket.
The arrow on the housing indicates
the direction of air-flow.
32
Silencer
To achieve even further reductions in
noise levels, a special silencer (optional
accessory) can be fitted in the ducting
system.
Extraction mode
The silencer not only reduces noise
from the motor outside the house, but
also sounds from outside (e.g. traffic
noise). For this reason the silencer must
be positioned as close as possible to
the ducting exit .
Connection for air extraction
Recirculation mode
The silencer needs to be positioned
between the exhaust socket and the
directional unit . Ensure there is
adequate space for fitting it.
33
Electrical connection
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent electrician in strict
accordance with current national and
local safety and building code
regulations.
Please ensure the connection data
(voltage and frequency) quoted on the
data plate match the household mains
supply. Please consult a qualified
electrician if you are in any doubt.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to
operate the appliance via a suitable
residual current device (RCD). Contact
a qualified electrician for advice.
Do not connect the appliance to the
mains electricity supply by a
multisocket adapter or an extension
lead. These are a fire hazard and do not
guarantee the required safety of the
appliance.
If the connection cable is faulty, it may
only be replaced by a qualified
electrician in order to avoid a hazard.
WARNING: THIS APPLIANCE MUST
BE EARTHED
34
After Sales / Guarantee
In the event of a fault which you cannot
remedy yourself, please contact your
Miele dealer.
Contact details your Miele dealer are
given at the end of this booklet. N.B. A
call-out fee will be charged for service
visits where the problem could have
been resolved as described in these
instructions.
When contacting your Miele dealer,
please quote the model and serial
number of your appliance.
These are shown on the data plate.
Position of the data plate
The data plate is visible after removing
the grease filters.
Guarantee
For information on the appliance
guarantee specific to your country
please contact your Miele dealer. See
end of this booklet for contact details.
35
Technical data
Fan motor
220 W
Hob lighting
DA 68 W
2x3W
DA 98 W
3x3W
Total connected load
DA 68 W
226 W
DA 98 W
229 W
Mains connection cable length
1.5 m
Weight
PUR 68 W
21 kg
PUR 98 W
25 kg
Accessories required for recirculation mode
DUW 20 kit to convert from extraction mode to recirculation mode and charcoal
filter DKF 12-1 or DKF 12-R (reactivatable).
36
Miele Saudi Arabia
AWAD BADI NAHAS TRADING CO. LTD
Head Office:
Jeddah
P.O. Box 11529 Jeddah 21463
Tel. +966 12 2560888, Fax. +966 12 2560555
Hotline for customer care: 920003240
Website: www.awadnahas.com
Branches:
Jeddah
Madina Road
Tel. +966 12 6970060, Fax. +966 12 6970012
Jeddah
Sitteen Street
Tel. +966 12 6611675, Fax. +966 12 6606852
Jeddah
Miele Gallery
Al Thanyyan Group Building, Al-Madina Road,
Near, Al Rowdah District, Jeddah
Tel. +966 12 6989339 Ext. 100
Fax. +966 12 6989339 Ext. 200
Riyadh
Olaya Street
Tel. +966 11 2013501, Fax. +966 11 2013502
Taif
Hadiya Street
Tel. +966 12 7327001, Fax. +966 12 7369596
Khobar
Al Zahran Road
Tel. +966 13 8646150, Fax. +966 13 8646190
Miele United Arab Emirates
Miele Appliances Ltd.
Gold & Diamond Park
Office No. 6-217
Sheikh Zayed Road
P.O. Box 114782 - Dubai
United Arab Emirates
Tel. +971 4 3044 999
Fax. +971 4 3418 852
800-MIELE (64353)
E-Mail: info@miele.ae
Website: www.miele.ae
Webshop: www.shop.miele.ae
Miele Gallery Dubai
Sama Tower (Ground Floor)
Dubai World Trade Center
Roundabout
Dubai
Miele Service Centre
Shed No. 9, Block B,
Jamal Al Ghurair Warehouses
Al Quoz Industrial III
Dubai
Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany
PUR 68 W
PUR 98 W

en-SA, AE
M.-Nr. 10 650 890 / 00
Download PDF