Page 1 of 3
Operating Instructions
RFRP Room Thermostat Wireless
Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Factory default settings
Specifications & wiring
Mounting
Installation
Frost protection
LCD symbol / buttons description
Resetting the thermostat
Keypad lock and unlock
Setting the date, time and operating mode
Factory program settings
Adjusting the program settings for 5/2d
Copy Function
Temporary override
Permanent override
Boost function
Holiday function
To connect the RFRP thermostat to an RF1A receiver
To disconnect the RFRP thermostat from an RF1A receiver
Backlight mode selection
Battery low warning
Replacing the batteries
1. Factory default settings
Temperature indicator:
Switching differential:
In built frost protection:
Clock:
Keypad lock:
Operating mode:
°C
0.4°C
5°C - Not adjustable
24 hours
Off
5/2 day
CAUTION!
The thermostat must not be left unsupervised
when open. (Prevent non specialists and especially
children from gaining access to it.)
Only qualified electricians or authorised service
staff are permitted to open the thermostat.
If the thermostat is used in a way not specified by
the manufacturer, its safety may be impaired.
Important: Keep this document
Prior to setting the thermostat, it is neccessary to
complete all required settings described in this section.
5. Frost protection
5°C
Frost protection is built into this thermostat.
It is pre fixed at 5°C and is not adjustable.
It will only be activated when the thermostat is in the OFF mode and the
room temperature falls below 5°C.
6. LCD Symbol / button description
2. Specifications & wiring
Power supply:
Power consumption:
Battery replacement:
Temp. control range:
Ambient temperature:
Dimensions:
Temperature sensor:
Temperature indication:
Switching differential:
Frost protection:
2 x AA Alkaline Battery
2 mW
Once a year
5 ... 35°C
0 ... 50°C
130 x 99 x 25mm
NTC 10K Ohm @ 25°C
˚C
0.4˚C
Only operational in OFF mode
6.1 LCD Symbol description
Current program
Temperature
Day of the week
Battery low symbol
Day / Month
Wireless symbol
Current Time
Heating on symbol
(Boost to time)
Keypad lock symbol
Operating mode
3. Mounting
2. Directly on walls.
3. Table mounting with stand provided.
4. Installation
Lower the flap at the front of the thermostat.
There is a battery compartment located below the buttons.
Using your 2 thumbs, apply pressure and pull downwards to remove the cover.
Insert the 2 x AA batteries and the thermostat will turn on.
Close the battery compartment.
6.2 Button description
Set point increase
Wireless connect button
Set point decrease
Automatic
mode
Reset button
AUTO
MAN
OFF
PROG
TIME
HOL
COPY
BOOST
OK
OK confirm button
(Back)
Boost mode
Manual
mode
Copy function
Off mode
Holiday mode
Program mode
Set Date/ Time
EPH Controls Ireland
EPH Controls UK
Sitecast Industrial Estate, Pouladuff,
Cork, T12 W665, Ireland
sales@ephcontrols.com www.ephcontrols.com
Unit E4, Welland Business Park, Valley Way, Market Harborough,
Leicestershire, LE16 7PS, United Kingdom
sales@ephcontrols.co.uk www.ephcontrols.co.uk
20170816_RFRP_OpIns_JW
The mounting height should be 1.5 meters above the floor level.
The thermostat should be wall mounted in the room where the heating is to
be controlled.
The place of installation should be chosen so that the sensor can measure the
room temperature as accurately as possible.
Choose the mounting location to prevent direct exposure to sunlight or other
heating / cooling sources when mounted.
The unit can be fitted to:
1. Recessed conduit boxes.
Page 2 of 3
Operating Instructions
RFRP Room Thermostat Wireless
11. Adjusting the program settings for 5/2d
7. Resetting the thermostat
It is necessary to reset the thermostat prior to initial programming.
Press the ‘PROG’ button once.
Press the
Programming for Monday to Friday is now selected.
RESET
button on the side of the thermostat.
‘rst no’ will appear on the screen.
Press the
or
buttons to adjust the P1 time. Press the ‘OK’ button.
Press the
Press the
or
buttons to adjust the P1 temp.
button.
Press the ‘OK’ button.
‘rst yes’ will appear on the screen.
Repeat this process to adjust P2 to P6 times and temperatures.
Press the ‘OK’ button to reset the thermostat.
Press the ‘OK’ button.
Programming for Saturday to Sunday is now selected.
8. Keypad lock and unlock
OFF
To lock the keypad, press and hold the
and
buttons for 10 seconds.
will appear on the screen. The keypad is now locked.
To unlock the keypad, press and hold the
and
Press the
or
buttons to adjust the P1 time. Press the ‘OK’ button.
Press the
or
buttons to adjust the P1 temp. Press the ‘OK’ button.
Repeat this process to adjust P2 to P6 times and temperatures.
Press the ‘AUTO’ button to return to automatic mode.
buttons for 10 seconds.
While in PROG Mode pressing the ‘PROG’ button will jump from P1-P2 etc
without changing the temperature.
will disappear from the screen. The keypad is now unlocked.
While in PROG Mode pressing the ‘TIME’ button will jump to the next Day
(block of days).
9. Setting the date, time and operating mode
If 7 D mode is selected, you can program each day of the week with 6
individual times and temperatures.
Press the ‘TIME’ button once, the day will begin flashing.
Press the
or
buttons to adjust the year.
Press the ‘OK’ button.
Press the
or
buttons to adjust the month. Press the ‘OK’ button.
Press the
or
buttons to adjust the day.
Press the ‘OK’ button.
Press the
or
buttons to adjust the hour.
Press the ‘OK’ button.
Press the
or
buttons to adjust the minute. Press the ‘OK’ button.
Copy function may only be used if the thermostat is in the 7d mode.
Press the
or
buttons to adjust from 5/2d to 7d or 24h mode.
Set the times and temperatures for the day that you wish to copy from in
PROG Mode.
Press the ‘AUTO’ button or wait 5 seconds and the thermostat will return to
normal operation.
10. Factory program settings
If 24H mode is selected, you can only program each day of the week with
the same 6 times and temperatures.
12. Copy function
When still on the day press the ‘COPY’ button.
The day of the week that you have selected will be shown with ‘COPY’
below it.
5/2d
The next day will begin to flash on the top of the screen.
5/2D
Sat-Sun
P2
P3
P4
P5
P6
06:30
08:00
12:00
14:00
17:30
22:00
21˚C
18˚C
21˚C
18˚C
21˚C
16˚C
08:00
10:00
12:00
14:00
17:30
23:00
21˚C
18˚C
21˚C
18˚C
21˚C
16˚C
Sat-Sun
P1
P2
P3
P4
P5
P6
06:30
08:00
12:00
14:00
17:30
22:00
21˚C
18˚C
21˚C
18˚C
21˚C
16˚C
08:00
10:00
12:00
14:00
17:30
23:00
21˚C
18˚C
21˚C
18˚C
21˚C
16˚C
P1
P2
P3
P4
P5
P6
06:30
08:00
12:00
14:00
17:30
22:00
21˚C
18˚C
21˚C
18˚C
21˚C
16˚C
24H
Everyday
button to copy the times and temperatures to that day.
Press the
button to skip a day.
You can copy to multiple days using the
button.
Press the ‘OK’ button when copying has been completed.
13. Temporary override
7D
Mon-Fri
Press the
When in AUTO mode, press the
temperature setpoint.
or
buttons to adjust the
‘OvEr’ will appear on the screen.
Press ‘OK’ or after 5 seconds the thermostat will operate in this temporary
override, util the next switching time.
To cancel temporary override, press the ‘OFF’ buttton and then press the
‘AUTO’ button to return to the automatic mode.
14. Permanent override
Press the ‘MAN’ button to enter Manual Mode (Permanent Override).
‘MAN’ will appear on the screen.
Press the
or
buttons to adjust the temperature setpoint.
Press ‘OK’ to confirm the temperature selection or after 5 seconds the
thermostat will operate in this permanent override.
The thermostat will operate in MAN mode until the mode is changed.
To cancel permanent override, press the ‘OFF’ button and then press the
‘AUTO’ button to return to automatic mode.
EPH Controls Ireland
EPH Controls UK
Sitecast Industrial Estate, Pouladuff,
Cork, T12 W665, Ireland
sales@ephcontrols.com www.ephcontrols.com
Unit E4, Welland Business Park, Valley Way, Market Harborough,
Leicestershire, LE16 7PS, United Kingdom
sales@ephcontrols.co.uk www.ephcontrols.co.uk
20170816_RFRP_OpIns_JW
Mon-Fri
P1
Page 3 of 3
Operating Instructions
RFRP Room Thermostat Wireless
15. Boost function
The thermostat can be boosted to a specific temperature for 1, 2 or 3
hours while the thermostat is operating in all modes except for holiday
mode.
Press the ‘BOOST’ button 1, 2 or 3 times, the time that the boost will be
activated to will flash on the screen.
If you do not press any other button the boost will activate to the
temperature displayed on the screen after 5 seconds.
If you press the ‘OK’ button the temperature will now flash. You can edit
the temperature if you press the
or
buttons.
Press the ‘OK’ button or wait for 5 seconds to enter BOOST Mode.
‘BOOST TO’ will now be displayed on the screen with the time that it is
activated to displayed above this text.
Press the ‘BOOST’ button again to deactivate the boost.
18. To disconnect the RFRP thermostat from an
RF1A receiver
On the RFRP thermostat:
Press the
CONNECT
button.
The thermostat will begin to search through the RF channels.
Press and hold the ‘COPY’ button for 10 seconds.
‘Addr’ will appear on the screen of the thermostat.
Press the ‘OK’ button twice to complete the unpairing process.
The thermostat RFRP is now disconnected from the receiver RF1A.
On the RF1A receiver:
Press the
RESET
button and immediately press the
button.
Connect
The red and green lights will flash quickly followed by a solid red light.
The RF1A receiver is now disconnected from the RFRP thermostat.
16. Holiday function
This will switch your heating system off between the start and end times
you select .
Press the ‘HOL’ button, ‘HOLIDAY FROM’ will appear on screen.
Press the
or
buttons to adjust the day.
Press the
or
buttons to adjust the month. Press the ‘OK’ button.
Press the ‘OK’ button.
Press the
or
buttons to adjust the year.
Press the ‘OK’ button.
Press the
or
buttons to adjust the hour.
Press the ‘OK’ button.
19. Backlight mode selection
There are two settings for selection. The factory default setting is AUTO.
OFF
The backlight is permanently OFF.
AUTO On pressing any button the backlight stays on for 5 seconds.
To adjust the backlight setting, lower the cover on the front of the unit.
‘HOLIDAY TO’ will appear on screen.
Press the ‘OK’ button.
Press the ‘OK’ button for 5 seconds.
Press the
or
buttons to adjust the day.
Press the
or
buttons to adjust the month. Press the ‘OK’ button.
Press either the
Press the
or
buttons to adjust the year.
Press the ‘OK’ button.
Press the‘OK’ button.
Press the
or
buttons to adjust the hour.
Press the ‘OK’ button.
The thermostat will now return to the mode it was in before the Holiday
settings were entered.
To cancel Holiday mode, press the ‘HOL’ button.
17. To connect the RFRP thermostat to an RF1A
receiver
Please note, If you are installing a CombiPack4 the RFRP thermostat and the
RF1A receiver will have a pre-established RF connection so it is not necessary
to carry out the RF connection process below.
On the RF1A receiver:
Press the
AUTO
button on the RF1A receiver.
Connect
The red and green light will begin to flash.
or
buttons to select the OFF or AUTO mode.
20. Battery low warning
When the batteries are almost empty, the
on the screen.
symbol will begin to flash
The batteries must now be replaced or the unit will shut down.
21. Replacing the batteries
Lower the flap at the front of the thermostat.
There is a battery compartment located below the buttons.
Using your 2 thumbs, apply pressure and pull downwards to remove
the cover.
Insert the 2 x AA batteries and the thermostat will turn on.
Close the battery compartment.
On the RFRP thermostat:
Press the
CONNECT
button.
The thermostat will begin to search through the RF channels.
Once an RF connection has been established the thermostat will show ‘r01’
on the LCD screen.
Press the ‘OK’ button to finish the process.
20170816_RFRP_OpIns_JW
The thermostat is now connected to the RF1A receiver.
EPH Controls Ireland
EPH Controls UK
Sitecast Industrial Estate, Pouladuff,
Cork, T12 W665, Ireland
sales@ephcontrols.com www.ephcontrols.com
Unit E4, Welland Business Park, Valley Way, Market Harborough,
Leicestershire, LE16 7PS, United Kingdom
sales@ephcontrols.co.uk www.ephcontrols.co.uk