INSTALLATION INSTRUCTIONS INSTRUCTIONS D'

INSTALLATION
INSTRUCTIONS
Commercial Stacked Dryer
Gas (120-Volt, 60-Hz)
or Electric
(120/240-Volt, 60-Hz)
INSTRUCTIONS
D’INSTALLATION
Sécheuse à usage
commercial superposée
à gaz (120 Volts, 60 Hz)
ou électrique
(120/240 Volts, 60 Hz)
TABLE OF CONTENTS
.
Page
Dryer Safety.......................................................................................................... 2
Tools & Parts ....................................................................................................... 5
Dimensions/Clearances .............................................................................. 6
Location Requirements ................................................................................. 7
Gas Dryer Electrical Requirements ........................................................ 8
Gas Requirements ........................................................................................... 9
Electric Dryer Electrical Requirements ............................................. 10
Dryer Venting Requirements ................................................................... 13
Gas Supply Connection ............................................................................. 15
Electric Dryer Electrical Connections ................................................ 17
Leveling ............................................................................................................... 21
Complete Installation .................................................................................. 22
Reversing Dryer Door Swing ................................................................... 23
Maintenance Instructions .......................................................................... 24
If You Need Assistance .............................................................................. 24
Electronic Control Setup Instructions ................................................ 25
Warranty ............................................................................................................. 30
W10761033A
W10761034A-SP
TABLE DES MATIÈRES
.
Page
Sécurité de la sécheuse............................................................................. 31
Outils et pièces .............................................................................................. 34
Dimensions/Distances de dégagement .......................................... 35
Exigences de l’emplacement................................................................... 36
Exigences électriques pour la sécheuse à gaz.............................. 37
Exigences de gaz........................................................................................... 38
Exigences électriques pour la sécheuse électrique ................ 39
Exigences concernant l’évacuation de la sécheuse .................. 40
Raccordement à la canalisation de gaz ............................................. 42
Nivellement ........................................................................................................44
Achever l’installation .....................................................................................45
Inversion du sens d’ouverture de la porte ........................................46
Instructions d’entretien ................................................................................ 47
Si vous avez besoin d’assistance .......................................................... 47
Instructions de réglage du tableau
de commande électronique ......................................................................48
Garantie ............................................................................................................. 55
www.maytagcommerciallaundry.com
DRYER SAFETY
■■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells
gas. This information should be obtained from your gas supplier.
■■ Post the following warning in a prominent location.
2
DRYER SAFETY
IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
3
DRYER SAFETY
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the
following:
■■ Read all instructions before using the dryer.
■■ Clean dryer lint screen before or after each load.
■■ This dryer is intended only for drying clothes and textiles
■■ Do not use this dryer without the lint screen in place.
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■
that have been washed in water. Do not use for any other
purpose.
WARNING: If you smell gas, do not use the dryer or any
electrical equipment nearby. Warn other people to clear the
area. Contact the dryer owner immediately.
Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-cleaning
solvents, other flammable, or explosive substances as they
give off vapors that could ignite or explode.
Do not dry unwashed items in the dryer.
Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is used
near children.
Before the dryer is removed from service or discarded,
remove the doors to the dryer compartment.
Do not reach into the dryer if the drum is moving.
Do not open door while dryer is in operation. It will stop.
Do not install or store the dryer where it will be exposed to
water and/or the weather.
Do not tamper with controls.
■■ Do not repair or replace any part of the dryer or attempt any
■■
■■
■■
■■
■■
■■
■■
servicing unless specifically recommended in this Installation
Instructions or in published user-repair instructions that you
understand and have the skills to carry out.
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
The final part of a tumble dryer cycle occurs without heat
(cool-down cycle) to ensure that the articles are left at a
temperature that ensures that the items will not be damaged.
WARNING: Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated. (Avoids risk of
spontaneous combustion).
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
The interior of the dryer and dryer exhaust vent should be
cleaned periodically by qualified service personnel.
See “Electrical Requirements” section for grounding
instructions.
SAVE THESE INSTRUCTIONS
4
TOOLS & PARTS
Tools Needed:
8" (200 mm) or 10" (250 mm)
Pipe wrench
Torx T-20®† security screwdriver or bit
8" (200 mm) or 10" (250 mm) Adjustable wrench
that opens to 1" (25 mm)
Flat-blade screwdriver
1" (25 mm) Hex-head
5⁄16" (8 mm) Socket wrench
socket wrench
Level
Utility knife
1/4" (6 mm) Nut driver
Caulk gun and caulk
Vent clamps
(for installing new exhaust vent)
Flashlight (optional)
1" (25 mm)
Open-end wrenches
Pipe-joint compound suitable for gas type
Phillips screwdriver
Pliers (that open to
19/16" [39 mm])
27" (686 mm) Wood block
Putty knife
Ruler or measuring tape
Parts Supplied:
Security cotter pins (2)
†® TORX and T-20 are registered trademarks of Acument Intellectual Properties, LLC.
5
DIMENSIONS/CLEARANCES
Dimensions
Front View
Side View
51/2"
(140 mm)
Back View
27"
(686 mm)
101/2"
(267 mm)
763/8"
(1940 mm)
–
763/4"
PD Models
(1950 mm)
741/4"
(1886 mm) –
PR Models
411/2"
(1054 mm) –
PD Models
391/2"
(1003 mm) –
PR Models
Clearances
Recessed Front View
6
Recessed Side View
LOCATION REQUIREMENTS
Recessed Area Installation Instructions
This dryer may be installed in a recessed area. For recessed area
installations, minimum clearances can be found on the warning
label on the rear of the dryer or in “Dimensions/Clearances.”
The installation spacing is in inches and is the minimum allowable.
Additional spacing should be considered for ease of installation,
servicing, and compliance with local codes and ordinances.
The dryer must be exhausted outdoors.
Your dryer can be installed in a basement, laundry room,
or recessed area.
This dryer is not intended for installation in a mobile home.
Companion appliance location requirements should also be
considered.
IMPORTANT:
■■ Do not install or store the dryer where it will be exposed
to water and/or the weather. Proper installation is your
responsibility.
■■ This dryer must not be installed in a closet with a door.
You will need:
■■ A grounded electrical outlet located within 6 ft. (1.8 m) of
where the power cord is attached to the back of the dryer.
See “Electrical Requirements.”
■■ A level floor with a maximum slope of 1" (25 mm) under entire
dryer. Installing the dryer on soft floor surfaces, such as carpets
or surfaces with foam backing, is not recommended.
Dryer installation clearances
■■ The location must be large enough to allow the dryer door to be
fully opened.
■■ Additional spacing should be considered for ease of installation
and servicing. The door opens more than 180°.
■■ Additional clearances might be required for wall, door, and floor
moldings.
■■ Additional spacing of 1" (25 mm) on all sides of the dryer is
recommended to reduce noise transfer.
When installing a gas dryer:
IMPORTANT: Observe all governing codes and ordinances.
■■ Check code requirements: Some codes limit or do not
permit installation of clothes dryers in garages, closets, or
sleeping quarters. Contact your local building inspector.
■■ Make sure that lower edges of the cabinet, plus the back and
bottom sides of the dryer, are free of obstructions to permit
adequate clearance of air openings for combustion air. See
“Recessed Area Installation Instructions” below for minimum
spacing requirements.
7
GAS DRYER ELECTRICAL REQUIREMENTS
Gas Dryer Grounding
IMPORTANT: The dryer must be electrically grounded in
accordance with local codes and ordinances or, in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70,
latest edition, or Canadian Electrical Code, CSA C22.1. If codes
permit and a separate ground wire is used, it is recommended
that a qualified electrical installer determine that the ground path
is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park, Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
■■ Do not ground to a gas pipe.
■■ Do not have a fuse in the neutral or ground circuit.
■■ A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical
circuit is required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this dryer be provided.
■■ If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
■■ Check with a qualified electrician if you are not sure the dryer
is properly grounded.
8
GAS REQUIREMENTS
Gas Supply
IMPORTANT: Observe all governing codes and ordinances.
This installation must conform with all local codes and ordinances.
In the absence of local codes, installation must conform with
American National Standard, National Fuel Gas Code ANSI
Z223.1/NFPA 54 or CAN/CSA B149.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park, Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
The design of this dryer has been certified by CSA International
for use at altitudes up to 10,000 feet (3048 m) above sea level at
the B.T.U. rating indicated on the model/serial plate. Burner input
adjustments are not required when the dryer is operated up to
this elevation.
When installed above 10,000 feet (3048 m), a four percent (4%)
reduction of the burner B.T.U. rating shown on the model/serial
plate is required for each 1,000 foot (305 m) increase in elevation.
For assistance when converting to other gas types and/or installing
above 10,000 feet (3048 m) elevation, contact your local service
company.
9
ELECTRIC DRYER ELECTRICAL REQUIREMENTS (U.S.A. ONLY)
It is your responsibility:
■■ To contact a qualified electrical installer.
■■ To be sure that the electrical connection is adequate and in
conformance with the National Electrical Code, ANSI/NFPA
70-latest edition and all local codes and ordinances.
■■ The National Electrical Code requires a 4-wire power supply
connection for homes built after 1996, dryer circuits involved
in remodeling after 1996, and all mobile home installations.
■■ A copy of the above code standards can be obtained from:
National Fire Protection Association, One Batterymarch Park,
Quincy, MA 02269.
■■ To supply the required 3 or 4 wire, single phase, 120/240 volt,
60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt
electrical supply, if specified on the serial/rating plate) on a
separate 30-amp circuit, fused on both sides of the line. A time
delay fuse or circuit breaker is recommended. Connect to an
individual branch circuit. Do not have a fuse in the neutral or
grounding circuit.
■■ Do not use an extension cord.
■■ If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Electrical Connection
To properly install your dryer, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
■■ This dryer is manufactured ready to install with a 3-wire
electrical supply connection. The neutral ground conductor is
permanently connected to the neutral conductor (white wire)
within the dryer. If the dryer is installed with a 4-wire electrical
supply connection, the neutral ground conductor must be
removed from the external ground connector (green screw),
and secured under the neutral terminal (center or white wire)
of the terminal block. When the neutral ground conductor is
secured under the neutral terminal (center or white wire) of the
terminal block, the dryer cabinet is isolated from the neutral
conductor.
■■ If local codes do not permit the connection of a neutral ground
wire to the neutral wire, see “Optional 3-wire connection”
section.
■■ A 4-wire power supply connection must be used when the
appliance is installed in a location where grounding through the
neutral conductor is prohibited. Grounding through the neutral
is prohibited for (1) new branch-circuit installations and (2)
areas where local codes prohibit grounding through the neutral
conductor.
10
Electric Dryer Grounding
ELECTRIC DRYER ELECTRICAL REQUIREMENTS (U.S.A. ONLY)
Electric Dryer Power Supply Cord
Direct Wire
If using a power supply cord:
Use a UL listed power supply cord kit marked for use with clothes
dryers. The kit should contain:
■■ A UL listed 30-amp power supply cord, rated 120/240 volt
minimum. The cord should be type SRD or SRDT and be at
least 4 ft. (1.22 m) long. The wires that connect to the dryer
must end in ring terminals or “U” shaped spade terminals
with upturned ends.
If connecting by direct wire:
Direct wire cable must match power supply (4-wire or 3-wire)
and be:
■■ Flexible armored cable or nonmetallic sheathed copper cable
(with ground wire), covered with flexible metallic conduit.
All current-carrying wires must be insulated.
■■ 10-gauge solid copper wire (do not use aluminum).
■■ At least 5 ft. (1.52 m) long.
■■ A UL listed strain relief.
If your outlet looks like this:
hen choose a 4-wire power supply cord with ring or
T
spade terminals and UL listed strain relief. The 4-wire
power supply cord, at least 4 ft. (1.22 m) long, must
have four 10-gauge copper wires and match a 4-wire
receptacle of NEMA Type 14-30R. The ground wire
(ground conductor) may be either green or bare.
4-wire
receptacle The neutral conductor must be identified by a white
(14-30R) cover.
If your outlet looks like this:
hen choose a 3-wire power supply cord with ring
T
or spade terminals and UL listed strain relief. The
3-wire power supply cord, at least 4 ft. (1.22 m)
long, must have three 10-gauge copper wires and
match a 3-wire receptacle of NEMA Type 10-30R.
3-wire
receptacle
(10-30R)
11
ELECTRIC DRYER ELECTRICAL REQUIREMENTS (CANADA ONLY)
Direct Wire
If connecting by direct wire:
Direct wire cable must match power supply (4-wire or 3-wire)
and be:
■■ Cable must be rated to 60 Amps minimum.
■■ Flexible armored cable or nonmetallic sheathed copper cable
(with ground wire), covered with flexible metallic conduit.
All current-carrying wires must be insulated.
■■ 6-gauge minimum solid copper wire (do not use aluminum).
■■ At least 5 ft. (1.52 m) long.
12
DRYER VENTING REQUIREMENTS
Elbows:
■■ 45° elbows provide better airflow than 90° elbows.
Good
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Better
Clamps:
■■ Use clamps to seal all joints.
■■ Exhaust vent must not be connected or secured with screws
or other fastening devices that extend into interior of duct and
catch lint. Do not use duct tape.
Dryer exhaust must not be connected into any gas vent, chimney,
wall, ceiling, attic, crawlspace, or a concealed space of a building.
Only rigid or flexible metal vent shall be used for exhausting.
4"
(102 mm)
4" (102 mm) Heavy, metal exhaust vent
■■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps may
be used.
■■ Do not use plastic or metal foil vent.
Rigid metal vent:
■■ Recommended for best drying performance and to avoid
crushing and kinking.
Flexible metal vent: (Acceptable only if accessible to clean)
■■ Must be fully extended and supported in final dryer location.
■■ Remove excess to avoid sagging and kinking that may result
in reduced airflow and poor performance.
■■ Do not install in enclosed walls, ceilings, or floors.
■■ The total length should not exceed 73⁄4 ft. (2.4 m).
NOTE: If using an existing vent system, clean lint from entire length
of the system and make sure exhaust hood is not plugged with
lint. Replace plastic or metal foil vents with rigid metal or flexible
metal vents. Review “Vent System Chart” and if necessary, modify
existing vent system to achieve best drying performance.
13
DRYER VENTING REQUIREMENTS
Vent Hoods
4" (102 mm) Diameter Exhaust Hoods
Box hood
Louvered hood
Exhaust hood must be at least 12" (305 mm) from the ground or
any object that may be in the path of the exhaust (such as flowers,
rocks, bushes, or snow).
Angled hood
12" min.
(305 mm)
Vent System Length
Maximum Vent Length/Vent Connection
Maximum length of vent system depends upon the type of vent
used, number of elbows, and type of exhaust hood.
3. Tighten hose clamp with Phillips screwdriver.
Vent System Chart (Rigid Metal Vent)
No. of 90˚ Turns
Box and
Louvered Hood
Angled Hood
0
64 ft. (19.5 m)
58 ft. (17.7 m)
1
54 ft. (16.5 m)
48 ft. (14.6 m)
2
44 ft. (13.4 m)
38 ft. (11.6 m)
3
35 ft. (10.7 m)
29 ft. (8.8 m)
4
27 ft. (8.2 m)
21 ft. (6.4 m)
For vent systems not covered by the vent specification chart,
see your parts distributor.
Provision must be made for enough air for combustion and
ventilation. (Check governing codes and ordinances.) See
“Recessed Area Installation Instructions” in the “Location
Requirements” sections.
A 4" (102 mm) outlet hood is preferred. However, a 21⁄2" (64 mm)
outlet exhaust hood may be used. A 21⁄2" (64 mm) outlet creates
greater back pressure than other hood types. For permanent
installation, a stationary vent system is required.
Connect Vent
1. If connecting to existing vent, make sure the vent is clean.
2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in dryer.
Vent collar
NOTE: Do not remove vent collar.
14
4. Make sure the vent is secured to exhaust hood with a 4"
(102 mm) clamp.
5. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
DRYER VENTING REQUIREMENTS
If an Exhaust Hood Cannot be Used
Multiple Dryer Venting
The outside end of main vent should have a sweep elbow directed
downward.
A main vent can be used for venting a group of dryers. The main
vent should be sized to remove 5663 l/min. (200 CFM) of air per
dryer. Large-capacity lint screens of proper design may be used in
main vent if checked and cleaned frequently. The room where the
dryers are located should have make-up air equal to or greater than
CFM of all the dryers in the room.
Back-draft Damper Kit, Part No. 3391910, is available from your
distributor and should be installed in the vent of each dryer to
keep exhausted air from returning into dryers and to keep exhaust
in balance within main vent. Unobstructed return air openings are
required.
Each vent should enter the main vent at an angle pointing in
the direction of the airflow. Vents entering from the opposite side
should be staggered to reduce the exhausted air from interfering
with the other vents.
12" min.
(305 mm)*
24" min.
(610 mm)
*Minimum clearance above any
accumulation of snow, ice, or
debris such as leaves
If main vent travels vertically through the roof, rather than through
wall, install a 180° sweep elbow on end of vent at least 2 ft.
(610 mm) above surface of roof.
The opening in wall or roof shall have a diameter 1⁄2" (13 mm)
larger than vent diameter. Vent should be centered in opening.
Do not install screening over end of vent for best performance.
30˚ max.
Air
airflow
flow
The maximum angle of each vent entering the main vent should be
no more than 30°.
Keep air openings free of dry cleaning fluid fumes. Fumes create
acids which, when drawn through the dryer heating units, can
damage dryers and items being dried.
A clean-out cover should be located on the main vent for periodic
cleaning of the vent system.
GAS SUPPLY CONNECTION
Make Gas Connection
1. Remove red cap from gas pipe on back of dryer.
2.Connect gas supply to dryer. Use a pipe thread compound
approved for the type of gas supplied. If flexible metal tubing
is used, be certain there are no kinks.
If necessary for service, open the toe panel. Use a putty knife
to press on the toe panel locks located at the upper corners
of the toe panel. Pull downward on the toe panel to open.
Toe panel is hinged at the bottom.
3.Open the shut-off valve in the gas supply line and make sure
the dryer has its own gas supply opened.
4.Test all connections by brushing on an approved noncorrosive
leak-detection solution. Bubbles will show a leak. Correct any
leaks found.
15
GAS SUPPLY CONNECTION
Type of Gas
This dryer is equipped for use with natural gas. It is design-certified
by CSA International for LP (propane and butane) gases with
appropriate conversion. No attempt shall be made to convert dryer
from gas specified on serial/rating plate for use with a different gas
without consulting the serving gas supplier. Conversion must be
done by a qualified service technician.
Gas conversion kit part numbers are listed on gas valve burner
base.
Gas Supply Line
Recommended Method
Provide a gas supply line of 1⁄2" (13 mm) rigid (IPS) pipe to dryer
location. Pipe joint compounds that resist action of LP gas must
be used. Do not use TEFLON®† tape. With LP gas, piping or tubing
size can be 1⁄2" (13 mm) minimum. Usually, LP gas suppliers
determine size and materials used in the system.
Gas Supply Pressure Testing
A 1/8" NPT minimum plugged tapping, accessible for gauge
testing, must be installed immediately downstream of the installed
shut-off valve to the dryer (as shown above). The dryer must
be disconnected from the gas supply piping system during any
pressure testing of the system at test pressures in excess of
1/2" psig (352 kg/m2).
Alternate Method
The gas supply may also be connected using 3⁄8" (10 mm)
approved copper or aluminum tubing. If the total length of the
supply line is more than 20 ft. (6.1 m), larger tubing will be
required.
If using natural gas, do not use copper tubing. Pipe joint
compounds that resist action of type of gas supplied must
be used.
Flexible Metal Appliance Connector
It is recommended that a new flexible stainless steel gas line,
design-certified by CSA International, be used for connecting the
dryer to the gas supply line. (The gas pipe which extends through
the lower rear of the dryer is provided with 3⁄8" male pipe thread.)
NOTE: Do not kink or damage the flexible stainless steel gas line
when moving the dryer.
Rigid Pipe Connection
The rigid pipe connection requires a combination of pipe fittings
to obtain an in-line connection to the dryer.
Shut-off valve required
The supply line must be equipped with a manual shut-off valve
installed within 6 ft. (1.8 m) of dryer in accordance with National
Fuel Gas Code, ANSI Z223.1. This valve should be located in
same room as dryer. It should be in a location that allows ease
of opening and closing. Do not block access to shut-off valve.
In Canada, an individual manual shut-off valve must be installed in
accordance with the B149 installation codes CAN/CGA B149.1
and CAN/CGA B149.2.
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
16
ELECTRIC DRYER ELECTRICAL CONNECTIONS (U.S.A. ONLY)
Strain Relief
Remove Terminal Block Cover
Direct Wire Strain Relief
1. Insert strain relief.
2. Insert conduit into strain relief and tighten clamp.
Power Supply Cord Strain Relief
1. Insert strain relief.
2. Insert power cord into strain relief.
17
ELECTRIC DRYER ELECTRICAL CONNECTIONS
Connection Options
Power Cord
4-wire receptacle (NEMA Type 14-30R)
Direct Wire
4-wire direct
1"
m)
(25 m
5
(127 "
mm
)
3-wire receptacle (NEMA Type 10-30R)
3-wire direct
Connecting 4-Wire Connection: Power Supply Cord
IMPORTANT: A 4-wire connection is required where local codes
do not permit the use of 3-wire connections.
Standard Power Supply Cord Connectors
Flanged spade connector
Connecting Power Cord Ground Wire
3. Connect ground wire (green or bare) with external ground
connector screw.
Ring Connector
Connecting Ground and Neutral Wires
1. Remove center terminal block screw and the ground wire
by removing the external ground connector screw.
Connecting Remaining Wires
4. Connect remaining wires with outer terminal block screws.
2. Connect ground and neutral wire to center terminal block.
18
ELECTRIC DRYER ELECTRICAL CONNECTIONS
Connecting 3-Wire Connection: Power Supply Cord
Standard Power Cord Connectors
Flanged spade connector
2. Connect neutral wire to center terminal block.
Ring Connector
Connecting Neutral Wire
1. Loosen or remove center terminal block screw.
3. Connect remaining wires with outer terminal block screws.
Connecting 4-Wire Connection: Direct Wire
IMPORTANT: A 4-wire connection is required where local codes
do not permit the use of 3-wire connections.
Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer
can be moved if needed.
Strip 5" (127 mm) of outer covering from end of cable, leaving bare
ground wire at 5" (127 mm). Cut 11⁄2" (38 mm) from 3 remaining
wires. Strip insulation back 1" (25 mm). Shape ends of wires into
a hook shape.
Connecting Ground and Neutral Wires
1. Remove center terminal block screw and the ground wire by
removing the external ground connector screw.
19
ELECTRIC DRYER ELECTRICAL CONNECTIONS
Connecting 4-Wire Connection: Direct Wire
Connecting Ground and Neutral Wires (cont.)
2. Connect ground and neutral wire to center terminal block.
Connecting Remaining Wires
4. Connect remaining wires to outer terminal block.
Connecting Direct Wire Ground
3. Connect ground wire (green or bare) with external ground
connector screw.
Connecting 3-Wire Connection: Direct Wire
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer
can be moved if needed.
Strip 31⁄2" (89 mm) of outer covering from end of cable. Strip
insulation back 1" (25 mm). If using 3-wire cable with ground wire,
cut bare wire even with outer covering. Shape ends of wires into
a hook shape.
2. Connect neutral wire to center terminal block.
Connecting Neutral Wire
1. Loosen or remove center terminal block screw.
3. Connect remaining wires to outer terminal block.
20
ELECTRIC DRYER ELECTRICAL CONNECTIONS
Connecting 3-Wire Connection: Optional
Use for direct wire or power supply cord where local codes
do not permit connecting cabinet-ground conductor to
neutral wire.
Connecting Neutral Wire
1. Remove center terminal block screw. Also remove neutral
ground wire by removing external ground conductor screw.
3. Connect remaining wires to outer terminal block.
2. Connect neutral wire and neutral wire of power supply cord/
cable to center terminal block.
4. Connect a separate copper ground wire from the external
ground conductor to an adequate ground.
LEVELING
Leveling your dryer properly reduces excess noise and vibration.
Not Level
LEVEL
Not Level
1. Remove cardboard from beneath dryer. Place a level on top
edges of dryer, checking each side and front. If not level, tip
dryer and adjust legs up or down as shown in Steps 3 and 4,
repeating as necessary.
21
LEVELING
2. G
rip dryer from top and rock back and forth, making sure all four
legs are firmly on floor. Repeat, rocking dryer from side to side. If
dryer rocks, go to Step 3 and adjust leveling legs. If all four legs
are in firm contact with floor, go to Step 4.
HELPFUL TIP: You may want to prop up front of dryer about 4"
(102 mm) with a wood block or similar object that will support
weight of dryer.
Jam
Jam nut
nut
4. W
hen dryer is level and all four legs are firmly in contact with the
floor, use a 1" or 25 mm open-end or adjustable wrench to turn
jam nuts counterclockwise (as viewed from above) on leveling
legs tightly against dryer cabinet.
HELPFUL TIP: You may want to prop dryer with wooden block.
3. If dryer is not level, use a 1" or 25 mm open-end or adjustable
wrench to turn jam nuts clockwise (as viewed from above) on
legs until they are about 1/2" (13 mm) from the dryer cabinet.
Then turn the leveling leg counterclockwise to lower the dryer or
clockwise to raise the dryer. Recheck levelness of dryer and that
all four legs are firmly in contact with the floor. Repeat as needed.
COMPLETE INSTALLATION
1. C
heck the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. See “Electrical Requirements.”
2. C
heck that all parts are now installed. If there is an extra part,
go back through the steps.
3. C
heck that you have all of your tools.
4. D
ispose of/recycle all packaging materials.
5. Plug into a grounded outlet, or connect power.
22
6. C
heck dryer operation. Close dryer door. Select the cycle. Using
a full heat cycle (not the air cycle), let the dryer run for at least five
minutes. Dryer will stop when time is used up.
NOTE: Dryer door must be closed for dryer to operate. When
door is open, dryer stops, but timer continues to run. To restart
dryer, close door and re-select the cycle.
7. Open the dryer door. Check that the inside of the dryer is warm.
If the burner does not ignite and you can feel no heat inside
the dryer, shut off dryer for five minutes. Check that all supply
valve controls are in “ON” position and that the electrical cord
is plugged in. Repeat five-minute test.
8. If drying time is too long, make sure that the lint screen is clean
and that there are no obstructions to airflow in the dryer vent
system.
9. R
estart the dryer and allow it to complete a full heat cycle
(not air cycle) to make sure it is working properly.
REVERSING DRYER DOOR SWING (OPTIONAL)
You can change your door swing from a right-side opening to
left-side opening, if desired.
Remove the Door Assembly
1. Place a towel or soft cloth on top of work space to avoid
scratching of the surface.
2. Open dryer door. Remove button screws from cabinet side
of hinges. Loosen (do not remove) top screws from cabinet
side of hinges.
7. Be certain to keep cardboard spacer centered between doors.
Reattach outer door panel to inner door panel so handle is on
the side where hinges were just removed.
Door catch
Plugs
8. Reattach screws at top, bottom, and side of door (5 screws).
Hinges
3. Lift door until top screws in cabinet are in large part of hinge
slot. Pull forward off screws. Set door (handle side up) on top
of towel. Remove top screws from cabinet.
4.Remove screws attaching hinges to door.
5. Remove screws at top, bottom, and side of door (5 screws).
6. Holding door over towel, grasp sides of outer door and gently
lift to separate it from inner door. Do not use a putty knife to pry
apart. Do not pull on door seal or plastic door catch.
9. Attach door hinges to dryer door so that larger hole is at the
bottom of the hinge and the hinge pin is toward the door front.
10. R
emove the 4 screws that attach 2 plugs on the left side.
Attach plugs to right side using the same 4 screws.
11. Insert screws into bottom holes on left side of cabinet. Tighten
screws halfway. Position door so large end of door hinge slot
is over screws. Slide door up so screws are in bottom of slots.
Tighten screws. Insert and tighten top screws in hinges.
12. C
lose door and check that door strike aligns with door catch.
If needed, slide door catch left or right within slot to adjust
alignment.
23
MAINTENANCE INSTRUCTIONS
■■ Clean lint screen before and after each cycle.
■■ Removing accumulated lint:
From inside the dryer cabinet:
Lint should be removed every 2 years or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
From the exhaust vent:
Lint should be removed every 2 years, or more often, depending
on dryer usage.
■■ Keep area around dryer clear and free from combustible
materials, gasoline, and other flammable vapors and liquids.
■■ Keep dryer area clear and free from items that would obstruct
the flow of combustion and ventilation air.
If dryer does not operate, check the following:
■■ Electrical supply is connected.
■■ Circuit breaker is not tripped or house fuse is not blown.
■■ Door is closed.
■■ Controls are set in a running or “on” position.
■■ Cycle has been selected.
■■ For gas dryers, check that gas supply shut-off valves are set
in open position.
IF YOU NEED ASSISTANCE
Contact your authorized Commercial Laundry distributor. To locate your authorized Commercial Laundry distributor, or for web inquiries,
visit www.MaytagCommercialLaundry.com.
If you cannot locate your distributor, the Commercial Laundry Support Center will answer any questions about operating or maintaining
your dryer not covered in the “Installation Instructions.”
Just dial 1-800 NO BELTS (1-800-662-3587) — the call is toll free.
When you call, you will need the dryer model number and serial number. Both numbers can be found on the serial-rating plate located
in the dryer door opening.
24
ELECTRONIC CONTROL SETUP INSTRUCTIONS
IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
■■ Use an anti-static wrist strap. Connect wrist strap to green
ground connection point or unpainted metal in the appliance.
-ORTouch your finger repeatedly to a green ground connection point
or unpainted metal in the appliance.
■■ Before removing the part from its package, touch the
anti-static bag to a green ground connection point or
unpainted metal in the appliance.
■■ Avoid touching electronic parts or terminal contacts; handle
electronic control assembly by edges only.
■■ When repackaging failed electronic control assembly in
anti-static bag, observe above instructions.
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing is in
effect (stacked PD models also require Fixed Cycle with Top Off
option to be selected). Cycle time can be purchased one coin at a
time (PD models) up to the maximum time of 99 minutes. Stacked
PD models will credit all money to a cycle with a single button press
while in accumulator pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer “Top Off” capability will allow time to be
added to an existing dry cycle in increments equal to the number
of minutes of dry time per quarter (coin 1), up to 99 minutes,
regardless of the cost required to start the dryer. No credit is given
for coins or debit inputs entered when the control is displaying
99 minutes.
PR Models: In Enhanced Debit Mode, the top off price can be set
independently. (See VALUE OF COIN 2), and the top off time is
calculated according to the following equation:
top off price
full cycle price
=
top off time
full cycle length
Penny increment offset is not applied to top off purchases.
BLANK DISPLAY – This condition indicates the dryer is inoperative.
Enter set-up mode to view diagnostic code.
FREE CYCLES – This is established by setting the cycle price
to zero. When this happens, “SELECT CYCLE” will appear
rather than a cycle price. Any cycle started as a free cycle
will automatically terminate when the door is opened.
“0 MINUTES” SHOWING IN DISPLAY – This indicates the cycle
is complete and the dryer cannot be operated. Coins dropped
or debit inputs during this condition will be stored in escrow but
cannot be used until normal operation is restored by opening and
closing the door. If a door switch has failed, it must be replaced
before normal operation can be restored.
DEBIT CARD READY – This dryer is debit card ready. It will
accept a variety of debit card systems, but does NOT come with a
debit card reader. Refer to the debit card reader manufacturer for
proper dryer setup. In models converted to a Generation 1 debit
card system, debit pulses represent the equivalent of one coin
(coin 1).
COLD START (Initial first use) – Dryer is programmed at the
factory as follows:
5 minutes dry time/quarter (coin 1)
$1.50 dry price (fixed cycle with top off – PD Models)
$0.00 dry price (fixed cycle – PR Models)
Display
General User Information
After the dryer has been installed and plugged in, the display will
show “0 minutes.”
Stacked PR Models
WARM START (after power failure) – A few seconds after power
is restored, if a cycle was in progress at the time of the power
failure, “RESELECT CYCLE” will flash in the display, indicating
a button needs to be pressed to restart dryer.
0
MINUTES
0
PRICING – After the door is opened and then closed following the
completion of a cycle, the display indicates the cycle price (unless
set for free operation). As coins are dropped or debit inputs arrive,
the display will change to lead the user through the initiation of
a cycle.
There are four (4) types of dryer pricing:
Fixed “Vend” Pricing
A dryer set up for “Fixed Cycle” operation can only accept
additional time accumulated by increments equal to the length of a
complete dry cycle. A maximum of 99 minutes may be purchased;
no additional credit is given for coins dropped with 99 minutes in
the display.
MINUTES
UPPER DRYER
WHITES
& COLORS
HIGH HEAT
WHITES
& COLORS
HIGH HEAT
PERMANENT
PRESS
DELICATES
MEDIUM HEAT
LOW HEAT
PERMANENT
PRESS
DELICATES
MEDIUM HEAT
LOW HEAT
LOWER DRYER
Once the unit has been plugged in and the dryer door opened
and closed, the display will show the price. In PR models set for
free cycles, the display will flash “SELECT CYCLE” (not shown).
Stacked PD Models
PRICE
1.50
PRICE
1.50
UPPER DRYER
WHITES
& COLORS
HIGH HEAT
WHITES
& COLORS
HIGH HEAT
PERMANENT
PRESS
DELICATES
MEDIUM HEAT
LOW HEAT
PERMANENT
PRESS
DELICATES
MEDIUM HEAT
LOW HEAT
LOWER DRYER
25
ELECTRONIC CONTROL SETUP INSTRUCTIONS
Control Set-up Procedures
CodeExplanation
IMPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are used
to set up the dryer controls. The display can contain 4 numbers
and/or letters and a decimal point. These are used to indicate
the set-up codes and related code values available for use in
programming the appliance.
606 How to Use the Buttons to Program the Controls
1. The WHITES AND COLORS button is used to adjust the values
associated with set-up code. Pressing the button will change
the value by increments of one (1). Rapid adjustment is possible
by holding down the button.
2. The PERM. PRESS button will advance through the set-up
codes. Pressing the button will advance to the next available
set-up code. Holding down the PERM. PRESS button will
automatically advance through the set-up codes at a rate faster
than one (1) per second.
3. The DELICATES button is used to select or deselect options.
IMPORTANT: The console must not be opened unless power is
first removed from the dryer. To access connector AA1:
g Unplug dryer or disconnect power.
g Open console, disconnect plug on AA1, close console.
g Plug in dryer or reconnect power.
■■ Stacked PD Models: Insert access panel key and turn
counterclockwise.
■■ Stacked PR Models: Once the debit card reader is installed
(according to the reader manufacturer’s instructions), the
set-up mode can be entered by inserting a manual set-up
card (supplied by the reader manufacturer) into the card slot.
If manual set-up card is not available, manual set-up mode can be
entered by turning the access panel key.
The dryer is now in the set-up mode.
NOTE: This dryer is preset at the factory and does not require any
programming. However, if you want to change the settings, follow
the “Set-Up Codes” guide below.
■■ PD Units are pre-set at the factory for fixed cycle price with
top off.
■■ PR units are pre-set for free cycle operation so they can be run
without readers or coins.
Set-Up Codes
■■ The PERM. PRESS button will advance you from code to code.
■■ The WHITES AND COLORS button will change the code
value.
■■ The DELICATES button will select or deselect options.
FOR PR MODELS: The set-up codes are the same as for the PD
models except where noted.
NOTE: On all stacked dryer models, programming selections apply
to both dryers. Stacked dryer selections are accessed by pressing
the LOWER DRYER buttons.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or three
right-hand characters.
26
REGULAR CYCLE PRICE
606Represents the number of quarters (coin 1) needed
to start the dryer; may adjust from 0–39 (See
VALUE OF COIN 1 b.05). Advance from 0–39 by
pressing the WHITES AND COLORS button. Factory
default of 6 quarters = $1.50.
PR MODELS ONLY: Factory preset for 0 quarters.
Press the PERM. PRESS button once to advance
to next code.
•
705 REGULAR DRY TIME
705
Represents the number of minutes per quarter (coin 1).
Factory default of 5 minutes per coin.
Example: 6 quarters x 5 minutes = 30 minutes.
By pressing the WHITES AND COLORS button, value
adjusts from 1–99 minutes.
Press the PERM. PRESS button once to advance
to next code.
•
800 TYPE OF DRYER PRICING
800Fixed Cycle with Top Off. For detailed description, see
“General User Information.”
8FCFixed Cycle. For detailed description, see “General User
Information.”
Use DELICATES button to make this selection.
PR MODELS ONLY: Factory preset for FC.
Press the PERM. PRESS button once to advance
to next code.
•
9 00 CYCLE COUNTER OPTION
This option is either NOT SELECTED “OFF” or
SELECTED “ON.”
9 00
9 0C
Not Selected “OFF.”
Selected “ON” and not able to be deselected.
Press the DELICATES button 3 consecutive times
to select “ON.” Once selected “ON” it cannot be
deselected.
Press the PERM. PRESS button once to advance
to next code.
•
•
If cycle counter (9 0C) is selected, the following is true:
1 00 Cycles in HUNDREDS
1 02 = 200
2 00 Cycles in ONES
2 25 = 25
TOTAL CYCLES = 225
This is “VIEW ONLY” and cannot be cleared.
Press the PERM. PRESS button once to advance to next code.
•
ELECTRONIC CONTROL SETUP INSTRUCTIONS
CodeExplanation
OPTIONS 3.XX – 9.XX TO USE IF SPECIAL PRICING
IS SELECTED
1. 00
CodeExplanation
1. 00 1. 0C
MONEY COUNTER OPTION
This option is either NOT SELECTED “OFF” or
SELECTED “ON.”
Not Selected “OFF.”
Selected “ON.”
Press the DELICATES button 3 consecutive times
to select “ON” and 3 consecutive times to remove
(Not Selected “OFF”). Counter resets by going from
“OFF” to “ON.”
1. C0Selected “ON” and not able to be deselected.
To select “ON” and not able to be deselected, first select “ON,” then within 2 seconds, press
the DELICATES button twice, the WHITES AND
COLORS button once, and exit set-up mode.
Press the PERM. PRESS button once to advance
to next code.
•
•
•
2. 00 SPECIAL PRICING OPTIONS
This option is either NOT SELECTED “OFF”
or SELECTED “ON.”
2. 00Not Selected “OFF,” and next available code will be A.00.
2. SP Selected “ON.”
Press the DELICATES button once to change this
selection.
If SPECIAL PRICING OPTION is selected, there is access
to codes “3.XX” through “9.XX.”
Press the PERM. PRESS button once to advance
to next code.
•
•
If money counter (1.0C or 1.C0) is selected, the following
is true:
3 00 Dollars in HUNDREDS
3 01 = $100.00
4 00 Dollars in ONES
4 68 = $ 68.00
5 00 Number of CENTS
5 75 = $ 00.75
TOTAL = $168.75
3.06 SPECIAL CYCLE PRICE
3.06Represents the number of quarters (coin 1) to start the
dryer; may adjust from 0–39. (See VALUE OF COIN 1
b.05.)
Advance from 0–39 by pressing the WHITES AND
COLORS button. Factory default of 6 quarters = $1.50.
PR MODELS ONLY: Factory preset for 0 quarters.
Press the PERM. PRESS button once to advance
to next code.
•
4.05
SPECIAL DRY TIME
4.05
Represents the number of minutes per quarter (coin 1).
Factory default of 5 minutes per coin.
Example: 6 quarters x 5 minutes = 30 minutes.
By pressing the WHITES AND COLORS button,
the value can be adjusted from 1–99 minutes.
Press the PERM. PRESS button once to advance
to next code.
5. 00 •
•
•
TIME-OF-DAY CLOCK, MINUTES
5. 00This is the TIME-OF-DAY CLOCK, minute setting; select
0–59 minutes by pressing the WHITES AND COLORS
button.
Press the PERM. PRESS button once to advance
to next code.
•
6. 00 TIME-OF-DAY CLOCK, HOURS
NOTE: Uses military time or 24 hr. clock.
6. 00This is the TIME-OF-DAY CLOCK, hour setting; select
0–23 hours by pressing the WHITES AND COLORS
button.
Press the PERM. PRESS button once to advance
to next code.
•
27
ELECTRONIC CONTROL SETUP INSTRUCTIONS
CodeExplanation
CodeExplanation
7. 00
S PECIAL PRICE START HOUR
NOTE: Uses military time or 24 hr. clock.
b. 05 7. 00This is the start hour; 0–23 hours.
Select START HOUR by pressing the WHITES AND
COLORS button.
Press the PERM. PRESS button once to advance
to next code.
•
•
8. 00This is the stop hour; 0–23 hours.
Select STOP HOUR by pressing the WHITES AND
COLORS button.
Press the PERM. PRESS button once to advance
to next code.
•
•
SPECIAL PRICE DAY
9. 10This represents the day of the week and whether special
pricing is selected for that day. A number followed by “0”
indicates no selection that particular day (9.10). A number
followed by an “S” indicates selected for that day (9.1S).
Days of the week (1–7) are selected by pressing the
WHITES AND COLORS button. Press the DELICATES
button once to select special pricing for each day chosen.
When exiting set-up code “9,” the display must show the current
day of week:
DISPLAY
DAY OF WEEK
CODE (selected)
10
Day 1 = Sunday
1S
20
Day 2 = Monday
2S
30
Day 3 = Tuesday
3S
40
Day 4 = Wednesday
4S
50
Day 5 = Thursday
5S
60
Day 6 = Friday
6S
70
Day 7 = Saturday
7S
•
Press the PERM. PRESS button once to advance
to next code.
A. 00 VAULT VIEWING OPTION
This option is either NOT SELECTED “OFF” or
SELECTED “ON.”
A. 00 Not Selected “OFF.”
A. SCSelected “ON.”
Press the DELICATES button once to change this
selection. When selected, the money and/or cycle
counts will be viewable (if counter option(s) is
selected) when the coin box is removed.
Press the PERM. PRESS button once to advance
to next code.
•
•
28
b. 05This represents the value of coin 1 in number of nickels:
05 = $0.25.
By pressing the WHITES AND COLORS button,
there is an option of 1–199 nickels.
Press the PERM. PRESS button once to advance
to next code.
•
•
C. 20 VALUE OF COIN 2
8. 00 SPECIAL PRICE STOP HOUR
NOTE: Uses military time or 24 hr. clock.
9. 10
VALUE OF COIN 1
C. 20 This represents the value of coin 2 in number of nickels:
20 = $1.00.
By pressing the WHITES AND COLORS button,
there is an option of 1–199 nickels.
PR MODELS ONLY: For PR models using Enhanced
Debit, this field represents the value of top off in nickels.
PR MODELS: Factory preset for $0.25.
Press the PERM. PRESS button once to advance
to next code.
•
•
d.00
COIN SLIDE OPTION
This option is either NOT SELECTED “OFF”
or SELECTED “ON.”
d.00 d.CS
Not Selected “OFF.”
Selected “ON.”
Press the DELICATES button 3 consecutive times
for this selection. When coin slide mode is selected,
set “b.” equal to value of slide in nickels. Set “606”
(REGULAR CYCLE PRICE) and “3.06” (SPECIAL
CYCLE PRICE) to number of slide operations.
NOTE: If the installer sets up “CS” on a coin drop model,
it will not register coins.
Press the PERM. PRESS button once to advance
to next code.
•
•
E. 00 ADD COINS OPTION
This option is either NOT SELECTED “OFF” or
SELECTED “ON.” This option causes the customer
display to show the number of coins (coin 1) to enter,
rather than the dollars-and-cents amount. The number
in the display changes as the coins are accepted.
E. 00 Not Selected “OFF.”
E. ACSelected “ON.”
Press the DELICATES button 3 consecutive times
to change this selection.
PR MODELS ONLY: In enhanced debit mode, this option
is not selectable.
Press the PERM. PRESS button once to advance
to next code.
•
•
ELECTRONIC CONTROL SETUP INSTRUCTIONS
CodeExplanation
END of SET-UP PROCEDURES
J. Cd
EXIT FROM SET-UP MODE
PAYMENT MODE (COIN/DEBIT OPTION)
J. CdBoth coin and debit selected. Press the DELICATES
button 3 consecutive times to change this selection.
J. C_Coins selected, debit disabled. Press the DELICATES
button 3 consecutive times to change this selection.
J._dDebit Card selected, coins disabled. Press the
DELICATES button 3 consecutive times to change this
selection.
J. EdEnhanced Debit is self-selected when a Generation 2
card reader is installed in the dryer. The Ed option cannot
be manually selected or deselected.
Press the PERM. PRESS button once to advance
to next code.
Stacked Models: Turn access panel key back to original position.
DIAGNOSTIC GUIDE
If the set-up mode is entered and one of the following has
occurred, the appropriate diagnostic code will be in the display.
STACKED DRYERS
CODE
EXPLANATION
d1/F-01
Invalid dryer door circuit
state – Sahara control does not
differentiate between invalid
state and open door state.
d4/F-01
CCU error – Sahara control will
send this error when the motor
feedback circuit is sensing
voltage with the door open or
when the motor should not be
on. The control does not know
if the relay is bad (stuck on), the
relay drive circuit is bad (shorted
causing the motor relay to stay
on), or the relay fedback circuit
is bad.
•
L. 00
PRICE SUPPRESSION OPTION
This option is either NOT SELECTED “OFF” or
SELECTED “ON.” This option causes the customer
display to show “ADD” or “AVAILABLE” rather than
the amount of money to add. (Used mainly in debit
installations.)
L. 00
Not Selected “OFF.”
L. PSSelected “ON.”
Press the DELICATES button once to change this
selection.
Press the PERM. PRESS button once to advance
to next code.
•
•
n. CE
LEAR ESCROW OPTION
C
This option is either NOT SELECTED “OFF” or
SELECTED “ON.” When selected, money held in escrow
for 30 minutes without further escrow or cycle activity will
be cleared.
n. 00
Not Selected “OFF.”
n. CESelected “ON.”
Press the DELICATES button once to change this
selection.
Press the PERM. PRESS button once to advance
to next code.
•
•
U. 00
d9
d12/F-01
•
Coin 2 Failure
d13
Upper dryer motor sense circuit
error on control board or due to
power line interference (upper
dryer cycles and upper dryer
display disabled until diagnostic
code is manually cleared).
d16
Gen 2 Debit Card
d17
Lower dryer door sense error on
control board or due to power
line interference (lower dryer
cycles and lower dryer display
disabled until diagnostic code
is manually cleared).
d20
Upper dryer motor control circuit
error (upper dryer cycles and
upper dryer display disabled
until diagnostic code is manually
cleared).
PENNY INCREMENT OFFSET
U. 00This represents the penny increment price offset used in
Generation 2 (Enhanced Debit) PR models. Choose from
0–4 pennies by pressing the WHITES AND COLORS
button.
Press the PERM. PRESS button once to advance
to next code.
Low voltage
29
MAYTAG® COMMERCIAL WASHER, DRYER, STACKED
DRYER/DRYER, COMMERCIAL STACK LAUNDRY,
AND MULTI-LOAD COIN OPERATED COMMERCIAL
WASHERS AND DRYERS WARRANTY
LIMITED WARRANTY (PARTS ONLY – LABOR NOT INCLUDED)
For the first five years from the original date of purchase, when this commercial appliance is installed, maintained, and operated according
to the instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (hereafter “Maytag”) will pay for factory
specified replacement parts to correct defects in materials or workmanship that existed when this commercial appliance was purchased.
This limited warranty does not include labor.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Maytag recommends that you use an “in network” service provider to diagnose and repair your Commercial Laundry product. Maytag will not
be responsible under this warranty to provide additional replacement parts as a result of incorrect diagnosis or repair by an “out of network”
service company. This limited warranty is valid in the United States or Canada and applies only when the commercial appliance is used in
the country in which it was purchased. This limited warranty is effective from the date of the original consumer purchase. Proof of original
purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. All other costs including labor, transportation, shipping, or custom duties for covered parts.
2. Factory specified replacement parts if this commercial appliance is used for other than normal, commercial use or when it is used in a
manner that is inconsistent to published user or operator instructions and/or installation instructions.
3. Service calls to correct the installation of your commercial appliance, to instruct you on how to use your commercial appliance, to replace
or repair house fuses, or to correct external wiring or plumbing.
4. Damage resulting from improper handling of product during delivery, theft, accident, alteration, misuse, abuse, fire, flood, acts of God,
improper installation, installation not in accordance with local electrical or plumbing codes, or use of products not approved by Maytag.
5. Pick up and delivery. This commercial appliance is designed to be repaired on location.
6. Repairs to parts or systems resulting from unauthorized modifications made to the commercial appliance.
7. The removal and reinstallation of your commercial appliance if it is installed in an inaccessible location or is not installed in accordance
with published installation instructions.
8. Damage resulting from exposure to chemicals.
9. Changes to the building, room, or location needed in order to make the commercial appliance operate correctly.
10. Factory specified replacement parts on commercial appliances with original model/serial numbers that have been removed, altered,
or cannot be easily determined.
11. Discoloration, rust, or oxidation of stainless steel surfaces.
12. Factory specified replacement parts as a result of incorrect diagnosis or repair by an “out of network” service company.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this commercial appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with
this commercial appliance, you should ask Maytag or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If you need service, please contact your authorized Maytag Commercial Laundry® distributor. To locate your authorized Maytag
Commercial Laundry® distributor, call 1-800-662-3587, or for web inquiries, visit www.MaytagCommercialLaundry.com.
30
For written correspondence:
Maytag Commercial Laundry® Service Department
2000 N M 63
Benton Harbor, Michigan 49022-2632 USA
02/14
For more information and pricing, contact:
100 Melrose Avenue
Cherry Hill, NJ 08003
www.equipmentmarketers.net
W10761033A
W10761034A-SP
Phone: 800.223.1376
Fax: 856.428.5477
maytag@equipmentmarketers.net
®/TM © 2015 Maytag. All rights reserved.
®/TM © 2015 Maytag. Tous droits réservés.
02/2015
Printed in U.S.A.
Imprimé aux États-Unis