model t23094 pneumatic metal shear

MODEL T23094
PNEUMATIC METAL SHEAR
OWNER'S MANUAL
Copyright © APRIL, 2011 By Grizzly Industrial, Inc.
Warning: No portion of this manual may be reproduced in any shape
or form without the written approval of Grizzly Industrial, inc.
#CR14035 printed in CHINA
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
SAFETY.............................................................................................................................2
Safety Instructions for Pneumatic Tools......................................................................2
Additional Safety Instructions for Pneumatic Shears..................................................3
SECTION 1: INTRODUCTION..........................................................................................4
Foreword......................................................................................................................4
Specifications...............................................................................................................4
Contact Info.................................................................................................................4
Identification.................................................................................................................5
SECTION 2: SETUP..........................................................................................................6
Unpacking....................................................................................................................6
Inventory......................................................................................................................6
Assembly.....................................................................................................................6
SECTION 3: OPERATIONS..............................................................................................7
Operation Overview.....................................................................................................7
SECTION 4: ACCESSORIES............................................................................................8
SECTION 5: MAINTENANCE.........................................................................................10
SECTION 6: SERVICE....................................................................................................11
Troubleshooting.........................................................................................................11
SECTION 7: PARTS........................................................................................................13
Main Parts Diagram...................................................................................................13
Main Parts List...........................................................................................................13
WARRANTY....................................................................................................................14
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminent hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTICE
This symbol is used to alert the user to useful information about proper operation of the equipment.
Safety Instructions for Pneumatic Tools
KEEP ALL SAFETY DEVICES IN PLACE
and in working order.
REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before operation.
KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should be
kept at a safe distance from work area.
MAKE WORKSHOP CHILD PROOF.
Make sure to lock your shop and shutOFF the power and air supply.
-2-
DO NOT FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
USE THE RIGHT TOOL. Do not force tool
or attachment to do a job for which it was
not designed.
DO NOT USE UNDER THE INFLUENCE
OF DRUGS OR ALCOHOL, OR WHEN
TIRED.
USE CORRECT AIR PRESSURE.
Exceeding the maximum PSI rating
of this tool may cause seal damage,
unpredictable operation, or line burst.
Model T23094 Pneumatic Metal Shear
USE PROPER AIR HOSE for the tool.
Make sure your air hose is in good
condition and is long enough to reach
your work without stretching.
SECURE WORK. Use clamps or a vise to
hold work when practical. It is safer than
using your hand and frees both hands to
operate tool.
MAINTAIN TOOLS WITH CARE. Keep
tools lubricated and clean for best and
safest performance. Follow instructions
for lubricating and changing accessories.
PREVENT ACCIDENTAL OPERATION.
Do not carry tool with hand on trigger
and always disconnect from air when not
in use.
MAINTAIN TOOLS WITH CARE. Keep
tools lubricated and clean for best and
safest performance. Follow instructions
for lubricating and changing accessories.
BE AWARE OF HOSE LOCATION. Hoses
can easily become a tripping hazard when
laid across the floor in a disorganized
fashion.
WEAR
APPROVED
HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause hearing
damage with prolonged exposure.
AIR LINE CONNECTION INSPECTION.
An air line that becomes disconnected
from a tool can whip violently, causing
severe injury. Verify that air line is
properly connected and the fittings are
tight and free of leaks. A leaking fitting
can indicate the fitting is cracked and is
about to fail.
WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry that
may get caught in moving parts. Nonslip footwear is recommended. Wear a
protective hair covering to contain long
hair.
ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask if cutting
operation is dusty. Everyday eyeglasses
only have impact resistant lenses, they
are NOT safety glasses.
Additional Safety Instructions for
Pneumatic Shears
CHANGING BITS. When servicing or
removing metal from the jaws, disconnect
the shear from air to prevent an accidental
start-up injury.
TOOL STABILITY. To establish the best
control possible when cutting, hold the
handle and housing with two hands, and
stabilize your hands and body against
a fixed object. When free-hand cutting
(using one hand) use a guide to slide the
pneumatic shear along when making the
cut to avoid severe injury.
Model T23094 Pneumatic Metal Shear
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other tools with caution and respect.
Failure to do so could result in
serious personal injury, damage to
equipment or poor work results.
-3-
SECTION 1: INTRODUCTION
Foreword
Contact Info
We are proud to offer this manual with
your new T23094! We've made every
effort to be exact with the instructions,
specifications, drawings, and photographs
of the T23094 we used when writing
this manual. However, sometimes we still
make an occasional mistake.
We stand behind our products. If you have
any service questions, parts requests
or general questions about the product,
please call or write us at the location listed
below.
Also, owing to our policy of continuous
improvement, your T23094 may not exactly
match the manual. If you find this to be the
case, and the difference between the
manual and T23094 leaves you in doubt,
check our website for the latest manual
update or call technical support for help.
For your convenience, we post all available
manuals and manual updates for free
on our website at www.grizzly.com. Any
updates to your model of tool will be
reflected in these documents as soon as
they are complete.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
E-Mail: techsupport@grizzly.com
We want your feedback on this manual.
If you can take the time, please email or
write to us at the address below and tell
us how we did:
Grizzly Industrial, Inc.
C/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
Specifications
Jaw Strokes Per Minute................................................................................................. 1,800
Average Air Flow.......................................................................................................... 5 CFM
Swivel Head Adjustment..................................................................................................360°
Maximum Cutting Thickness (Plastics)................................................................... 12 Gauge
Maximum Cutting Thickness (Sheet Aluminum)..................................................... 14 Gauge
Maximum Cutting Thickness (Mild Sheet Steel)..................................................... 20 Gauge
Maximum Cutting Thickness (Stainless Steel)........................................................ 22 Gauge
Width of Cut................................................................................................................ 5.05mm
Operating Air Pressure................................................................................................. 90 PSI
Maximum Air Pressure............................................................................................... 100 PSI
Air Inlet Size................................................................................................................ 1⁄4" NPT
Minimum Air Hose Inside Diameter..................................................................................... 3⁄8"
Net Weight.....................................................................................................................2.8 lbs
Shipping Weight...............................................................................................................3 lbs
-4-
Model T23094 Pneumatic Metal Shear
Identification
Body
Head
Angled
Slide
⁄ " Quick
Disconnect
Fitting
Removed
14
Trigger
Jaw Set
Filter
Screen
Jaw Retaining
Cap Screws
Swivel Head
Cap Screw
Exhaust
Port
Figure 1. Components and controls.
This tool presents serious injury
hazards to untrained users. Read
through this entire manual to become
familiar with the controls and operations before using the tool!
Model T23094 Pneumatic Metal Shear
-5-
SECTION 2: SETUP
Unpacking
Assembly
Your tool was carefully packaged for safe
transportation. Remove the packaging
materials from around your tool and inspect
it. If you discover the tool is damaged,
please immediately call Customer Service
at (570) 546-9663 for advice.
To assemble the pneumatic shear:
1.Remove the plastic plug from the air
inlet in the handle.
Save the containers and all packing
materials for possible inspection by the
carrier or its agent. Otherwise, filing a
freight claim can be difficult. When you are
completely satisfied with the condition of
your shipment, inventory the contents.
3.Thread the fitting into the pneumatic
shear air inlet and tighten.
If any non-proprietary parts are missing
(e.g., a nut or a washer), we will gladly
replace them; or for the sake of expediency,
replacements can be obtained at your
local hardware store.
2. Apply pipe sealant on the threads of
the quick disconnect fitting.
4.Press the trigger, and place a few
drops of air tool oil into the air inlet,
and release the trigger. The pneumatic
shear is ready for use.
Air supply setup tips:
•If the air hose is longer than 25-feet,
increase the air pressure to 100 PSI to
compensate for air flow restriction.
•
Inventory
Model T23094 Inventory (Figure 2)
A.Pneumatic Metal Shear......................1
B. Quick Disconnect Air Fitting................1
C. Bottle for Oil........................................1
D.Hex Wrench 4mm...............................1
For consistent air flow, use air hoses
with an inside diameter of 3⁄8" or larger.
•To eliminate air system moisture and
maintain automatic lubrication, install a
main or in-line filter water separator as
far as possible from the air compressor,
but before any automatic in-line oiler.
See examples in Figure 3.
In-Line
Oiler
Filter
Regulator
(Optional)
A
Your
Tool
D
C
B
Quick-Disconnect
Fittings
Male Female
Steel
Air Piping
Compressor
Filter
Lead-In Hose
Automatic
Water
(Optional)
Oiler
Separator
Main Air
Air
Supply Hose
Regulator
Figure 3. Typical air supply system.
Figure 2. Inventory.
-6-
Model T23094 Pneumatic Metal Shear
SECTION 3: OPERATIONS
Operation Overview
To complete a typical cutting operation,
the following is done:
1.Put on safety goggles and gloves.
This tool presents serious injury
hazards to untrained users. Read
through this entire manual to become
familiar with the controls and operations before using the tool!
2. Mark the cut line, secure the workpiece,
and clamp a guide to the workpiece if
needed.
3.Determine if the swivel head needs to
be rotated for optimum tool control and
cut line viewing.
•If so, loosen the swivel head cap
screw (see Figure 1, on Page 5),
rotate the head to the required
angle, and retighten the cap
screw.
EYE INJURY HAZARD!
Wear safety goggles with full eye
protection from all sides when
using this grinder.
LUNG/EAR
INJURY HAZARD!
Wear protective
equipment when
using this tool.
ACCIDENTAL
START HAZARD!
Disconnect before
service or tool
changes.
AIR PRESSURE
HAZARD!
Never exceed max
PSI rating for tool.
Model T23094 Pneumatic Metal Shear
4. Apply a few drops of air tool oil on the
jaws and in the air inlet fitting.
5. Connect the air supply hose to the
pneumatic shear.
6.Engage the tip of the jaws against the
edge of the sheet metal.
7.Pull the trigger, and in a controlled
manner, push the shear into the
workpiece to begin cutting. As the cut
progresses, keep the angled slide (see
Figure 1, on Page 5) flat against the
surface of the sheet metal, so the jaws
and sheet metal do not bind.
8. When finished, or if leaving the area,
disconnect the shear from air, and
store it away from children.
-7-
SECTION 4: ACCESSORIES
T23103—12" Slip Roll
This slip roll is just the ticket for live
steamers, model makers and small
jobbers. With its 12" ground and polished
rolls it can handle mild steel up to 22
gauge and also has 5 ⁄ 32", 15 ⁄ 64" and 5 ⁄ 16"
diameter grooves to handle rod and wire.
A great little machine!
T20881—In-Line Lubricator 1 ⁄4" NPT
T20887—Pressure Regulator 1 ⁄4" NPT
G6261—Water Filter 1 ⁄4" NPT
Install an in-line lubricator to apply oil
automatically. Install an air regulator right
at the tool for precise air control. Install a
filter in your air supply line to prevent water
from traveling into your expensive air tools,
and ruining them.
T20887
T20881
G6261
Figure 4. 12" slip roll.
Figure 6. In-line pneumatic accessories.
G7147—12" Hand Brake
This hand brake is perfect for the home
hobbyist and those delicate forming jobs
that need a fine touch bending mild steel up
to 18 ga. Fully adjustable cams for bending
from 0° to 135°. Features a ground bed for
clean, straight edge forming. Approximate
shipping weight: 49 lbs.
T20554—Compressor Oil 32 Oz
T20555—Tool Oil 8 Oz
This Porter Cable air compressor and tool
oil offers outstanding heat displacement
and friction reduction without eating away
at O-rings and other rubber components
like detergent motor oils.
Figure 5. 12" hand brake.
Figure 7. Air tool oil.
-8-
Model T23094 Pneumatic Metal Shear
G8780—Portable hand punch.
Producing 1 ton of force, this Hand Punch
has a 16 gauge capacity in mild steel,
brass and aluminum. Much
quicker and safer than drilling thin stock
and leaves no ragged edges. Includes
3
⁄ 32", 1⁄ 8", 5 ⁄ 32", 3 ⁄ 16", 7⁄ 32", 1⁄4" and 9 ⁄ 32" dies
and wrenches.
T10172—Sheet Metal Shrinker Stretcher
Make smooth radius curves in sheet
metal without cutting, welding, heating
or hammering. This tool shrinks sheet
metal on one side for inside curves and
expands sheet metal on the opposite side
for outside curves. Handles up to 16 gauge
aluminum, 18 gauge mild steel and 20
gauge stainless steel. Great for fabricating
fender flanges, collars, and long one-piece
strips with various angles.
Figure 8. Portable hand punch.
H3243—4" Vise Brake
H3244—5" Vise Brake
H3245—6" Vise Brake
These accessories are one of the slickest
and cheapest tools to accurately bend
sheet metal. The dies magnetically mount
on the vise jaws. Slide your sheet metal in
and bend by tightening the vise! The press
fingers are sectional and can be removed
allowing small boxes to be made. Great
crafter’s tool!
Figure 10. Sheet metal stretcher
shrinker.
Figure 9. Vise brake.
Model T23094 Pneumatic Metal Shear
-9-
SECTION 5: MAINTENANCE
ACCIDENTAL
START HAZARD!
Disconnect before
service.
AIR PRESSURE
HAZARD!
Never exceed max
PSI rating for tool.
EYE INJURY HAZARD!
Wear safety goggles with full eye
protection from all sides when
using or servicing this shear.
Lubrication
Daily Maintenance
In most cases for perodic tool use, manual
lubrication is sufficiant. However, if the tool
is to be used on a consistent basis, we
recommend installing an automatic oiler to
eliminate dry runs and ensure maximum
tool life. The two methods are explained
below.
Before and after each use:
• Check and replace any leaking air
fittings; bubbled, cut, or worn hoses.
Manual Lubrication: Every two hours of
use, place a few drops of air tool oil in
the air inlet fitting and at all pivot points.
Do not use motor oil as the additives can
corrode the tool seals. Next, connect the
tool to the air line and cover the exhaust
port (see Figure 1, on Page 5) with a rag.
Position the end of the tool safely away
from you, and run the tool for 30 seconds
to completely circulate the oil through the
tool and into the rag.
Periodically as required:
• Clean the filter screen behind the air
inlet fitting (see Figure 1).
Automatic Lubrication: Adjust the
automatic in-line oiler. Place a sheet of
paper next to the exhaust port, run the tool
at three or four 30-second intervals. When
finished, the paper should show a slight oil
stain. If no oil is seen or excessive oil drips
from the paper, adjust the oiler and repeat
this process until the adjustment is correct.
See Figure 3 for location.
•Drain water from the compressor tank,
water filter separator reservoirs, and
lubricate the pneumatic shear.
•If used, check and adjust any automatic
in-line oiler as required to maintain a
fine oil mist at the tool.
•Sharpen dulled jaws edges by removing
both jaw retaining cap screws (see
Figure 1), and the jaws. Next use a
dressing stone at the locations shown
below. Do not use a grinder.
Dress the Top
Dress the Bottoms
Don’t Dress Sides
Figure 11. Jaw sharpening locations.
-10-
Model T23094 Pneumatic Metal Shear
SECTION 6: SERVICE
Troubleshooting
IMPORTANT: Air tool repairs must be completed by a qualified service person.
Symptom
Possible Cause
Tool runs at
normal speed but
bogs down when
cutting, or tool
runs slowly with
little air exiting the
exhaust.
1.Pneumatic shear is being 1.Reduce feed pressure. Only cut
materials within limits of tool.
overloaded.
2.Dress or replace jaws.
2.Jaws are dull or loose.
3.Remove any metal that may be
3.Trigger is at fault.
binding trigger from full travel.
4.Intake filter screen is 4.Clean the filter screen behind
the air supply fitting (see Figure
clogged.
1, on Page 5).
5.Insufficient air supply volume 5.Set the regulator to 90 PSI, or
100 PSI if the air hose is longer
or pressure.
than 25 feet. Repair any leaking
fittings, remove all restrictions
and hose kinks. Ensure that all
hoses and lines have an inside
diameter of at least 3⁄8".
6.Incorrect
lubrication
is 6.Make sure tool is lubricated
affecting tool.
correctly and does not run
dry. Prevent oil from flooding
the air tool by re-adjusting the
automatic oiler.
7.Water is entering tool.
7.Service or reposition the air
filter water separator as far as
possible from the compressor.
This allows for maximum air
cooling and water condensation
for the water separator.
8.Air tool motor clogged with 8.Clean or rebuild the air tool as
oil-water sludge.
required, and correct moisture
or lubrication problem in the air
supply system.
Model T23094 Pneumatic Metal Shear
Solution
-11-
Symptom
Possible Cause
Solution
Tool does not
operate when the
trigger is pressed,
but air runs freely
from exhaust.
1.Motor is at fault.
1.Motor may be stuck in position
from
improper
storage.
Lubricate the air tool, remove
the swivel head cap screw
and the head. Using a 17mm
wrench, rotate the spindle back
and forth slightly a few times.
Next operate the air tool while
re-oiling several times in the
process to flush the tool.
2.Replace tool.
2.Motor or gearing is at fault.
Tool runs slowly,
1.Air regulator or tool
and only a small
adjustment is at fault.
amount of air exits
from the exhaust
port.
2.Trigger throttle valve
obstructed.
1.Adjust the air regulator to 90
PSI, or 100 PSI if the air hose is
longer than 25 feet. Re-adjust
the throttle valve screw to the
fully open position.
is 2.Disassemble the throttle valve
and clean out sludge and
contaminants.
3.Intake filter screen is 3.Clean the filter screen behind
clogged.
the air supply fitting (see Figure
1, on Page 5).
4.Motor loaded with moisture 4.Disassemble air tool, clean, and
or oil sludge.
relubricate. Lubricate air tool
and rotate spindle by hand a
few times. Next use the trigger
to operate the air tool, re-oiling
several times in the process to
flush the system.
Tool does
not shut OFF
when trigger is
released.
1.Trigger binding or throttle 1.Remove matter that is binding
valve at fault.
trigger, so throttle valve is free
to fully release.
2.Throttle valve stuck open.
2. Replace throttle valve spring or
O-rings.
Air tool becomes
hot or noisy
during operation.
1.Air tool heats up from 1.Repair air tool, and correct
insufficient lubrication or a
in-line
oiler
lubrication
worn bearing.
adjustment, or follow manual
lubrication requirements.
Air tool becomes
too cold to hold,
or ice crystals
form at exhaust
port.
1.The intake of moisture and 1. Keep compressor tank drained,
the pressure drop is causing
service, reposition, or add
moisture to freeze in the
additional water separators in
tool.
the supply system.
-12-
Model T23094 Pneumatic Metal Shear
SECTION 7: PARTS
Main Parts Diagram
Parts breakdown provided for
reference only. Not all parts
shown are available
for purchase.
27
32
31
23
25
21
24
26
20
29
4
30
42
33
35
28
14
16
13
6
41
15
37
8
17
36
18
19
11
10
5
2
12
42
9
22
40
7
38
39
1
3
Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
AIR INLET
EXHAUST SLEEVE
DUST PLUG
MOTOR HOUSING
COMPRESSION SPRING
O-RING 4 X 2MM
VALVE STEM
O-RING 12 X 3MM
SPOOL VALVE
TRIGGER
SET SCREW M4-.7 X 8
BALL BEARING 626 ZZ
REAR END PLATE
CYLINDER
ROTOR
ROTOR BLADE
FRONT END PLATE
BALL BEARING 626 ZZ
GASKET
PINION GEAR
GEAR PIN
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
THROTTLE CYLINDER
SHAFT
INTERNAL RING GEAR
BALL BEARING 6201 Z
CLAMP NUT
THRUST SPACER
PIN
BALL BEARING R8Z
ECCENTRIC NUT
HEAD
BARREL LOCK NUT
CAP SCREW M5-.8 X 30
TRIGGER PIN
SEAL PLATE
SLEEVE
JAW SET 3-PC
HEX WRENCH 4MM
BOTTLE FOR OIL
O-RING 10.6 X 1.8MM
O-RING 4 X 1.1MM
O-RING 11.5 X 1.8MM
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
PSS51M
P626ZZ
N/A
N/A
N/A
N/A
N/A
P626ZZ
N/A
N/A
N/A
Model T23094 Pneumatic Metal Shear
N/A
N/A
N/A
P6201Z
N/A
N/A
N/A
N/A
N/A
N/A
N/A
PCAP95M
N/A
N/A
N/A
N/A
PAW04M
N/A
N/A
N/A
N/A
-13-
WARRANTY
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.