Instruciton Manual - Salini Appliances

Important safety information
Using your appliance
Cleaning and maintenance
Technical data
Declaration of conformity
This User Instruction Manual contains important information, including safety & installation
points, which will enable you to get the most out of your appliance. Please keep it in a safe
place so that it is easily available for future reference; for you or any person not familiar
with the operation of the appliance.
General Information
Carefully read the following important information regarding installation safety and
maintenance. Keep this information booklet accessible for further consultations.
The appliance has been designed as an exhausting version (external exhaust) or as a filter
version (inter air recycle) range hood.
This appliance is designed for domestic household use and designed be used indoors only.
IMPORTANT: Your product warranty will be void if the installation is not in accordance with
the instructions. The installation must be carried out by a suitably qualified person, in
accordance with the with the manufacturer’s instructions, and must be connected in
accordance with all local electrical rules specifications.
The use of this appliance for any other purpose or in any other environment will void
Your new appliance is guaranteed against electrical or mechanical defects, subject to
certain exclusions, the foregoing does not affect your statutory rights.
Repairs may only be carried out by Service Engineers or an authorised service agent.
Check the appliance for damage after unpacking it. Do not connect or install the appliance
if it has been damaged in transport as this will void the warranty.
Warning and safety instructions
Ensure there is adequate ventilation of the room when the range hood is used at the
same time as appliances burning gas or other fuels. (Not applicable to appliances
that only discharge the air back into the room.)
This appliance complies with all current Australian and European safety legislation, and
designed to operate safely in normal use.
Follow the local laws applicable for external air evacuation.
Appliance shall only be used with rated voltage and frequency.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Ensure adequate ventilation in the environment for the safe operation of the cooker hood.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Do not check the status of the filters while the cooker hood is operating.
Do not touch the light bulbs after appliance use.
Do not disconnect the appliance with wet hands or force the supply cord.
Do not have flames under the cooker hood as this damages the filters and is a fire hazard.
In the instance of a gas hotplate, ensure the flames are covered by a pot to protect the
range hood. Flame cooking is prohibited underneath the cooker hood.
Disconnect the electrical plug prior to any maintenance or cleaning.
Cleaning should be carried out in accordance with the “Cleaning and Maintenance” section
to avoid possible hazards.
If the power cord is damaged it must be replaced by the manufacturer or a qualified service
In the event of any incident caused by a technical fault, disconnect the power and report the
fault to the service centre to be repaired.
Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities. Contact your local
government for information regarding collection systems
Electrical Caution
CAUTION! Cleaning operations must only be carried out when the range hood
is cool and disconnected from the power supply.
Any work on electric equipment and systems may only be carried out by authorised
qualified persons.
In case of any damage, switch off the appliance and disconnect it from the power supply.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
WARNING: Ensure that the appliance is switched off before replacing the light globe to
avoid the possibility of electric shock.
The range hood should be placed at a distance of 65-75cm from the cooking surface for best effect.
Installation Option 1: (See drawing below)
To install onto the wall, mark and drill 4 holes of Ø8mm according to the dimensions on the
diagram. Measurements are taken from the centre of the holes in the back of the range
Insert the wall plugs into the holes in the wall.
Insert the screws into the wall plugs and tighten the screws.
Install the range hood onto the fixed screws.
Put the air outlet and extendable pipe onto the range hood. (the extendable pipe is optional
not supplied)
Installation Option 2: (See drawing below)
Drill 6 holes of 4mm diameter at the bottom of the hanging cupboard according to the
dimensions in the diagram.
Put the air outlet on the range hood, then install the range hood underneath the cupboard,
tighten the hood with enclosed 6 screws.
Install the adjusted board on the bottom of the hood in order to keep the gap between hood
back and cupboard.
Connect the plug into the power.
Push the switch ① in “
”, to turn the light on; push into “0”, to turn the light off.
Push the switch ② in “I or II”, the hood has two speeds “low or high”, push into “0”, to turn
the hood off.
The cooker hood will work at low or high speed when the front panel is pulled out.
It is recommended to operate the appliance prior to cooking.
There shall be adequate ventilation of the room when the range hood is used at the same time
as appliances burning gas or other fuels. (Not applicable to appliances that only discharge the
air back into the room.)
It is recommended to leave the appliance in operation for 15 minutes after cooking is
terminated in order to completely eliminate cooking vapours and odours.
If the appliance is not being used, please turn off.
Do not have flames under the range hood.
Don’t use or stop use immediately if the appliance is damaged especially the supply cord or the
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Don’t immerse the appliance in liquid.
The exhaust air must not discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
Regulations concerning the discharge of air have to be fulfilled.
In order to prevent fire hazard, it is recommended to clean the filter at a minimum of 2 monthly
by carrying out the following:
 Unplug before cleaning, then remove the filters from the cooker hood and wash them in a
solution of water and neutral liquid detergent, leaving to soak.
 Rinse thoroughly with warm water and leave to dry.
 The filters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several washes. This is not cause for customer
complaint nor replacement of panels.
Clean the surface of the cooker hood regularly using a cloth moistened with denatured alcohol
or non-abrasive liquid detergent. (Do not clean the motor and inside mechanisms.)
Replace filters approximately every 4 months.
There is a fire risk if cleaning is not carried out in accordance with these instructions.
Replace the light globe. See pic 5
Carbon filter (not supplied)
Carbon filters can be used to trap odours. Normally the activated carbon filter should be
changed at three or six months according to your cooking habits. Activated carbon filters
cannot be washed or recycled. The installation procedure of activated carbon filters is as below.
Slide the front part of the cooker hood.
In order to install the activated carbon filter, the Al anti-grease filter should be detached first.
Press the lock and pull it downward.
Put the activated carbon filter into the unit and turn it in anti-clockwise direction. Repeat the
same on the other side. Put the grease filter back in position.
Note: When the activated carbon filter is installed, the suction power will be reduced.
If you suspect that your appliance is not functioning correctly, we advise you read below
troubleshooting information to help you identify and asses how to best rectify any issues.
Servicing of the appliance must only be carried out by an authorised service representative and
the appliance must not be modified. Power must be disconnected before any servicing or
maintenance is conducted.
The extractor fan ceases to
Insufficient suction power.
Possible cause
The supply cable is not
connected to the power.
Connect supply cable to the power
There is no electrical current
Check that there is electrical current,
in the network.
check the fuse box.
Did not set to the right
speed and/or air outlet
being blocked.
If the kitchen hood is set up for
recirculation, check that the charcoal
filter is still effective.
If the kitchen hood is set up for
extraction, check that the ducting
and outlets are not blocked.
The kitchen is adequately vented to
allow the entry of fresh air.
Turn off the hood and then wait for
the device to reset.
Hood has switched off during The safety cut-out device
has been tripped.
The lights do not work.
Hood vibrates during
If the hood has been installed below
the heights indicated in the
installation instructions, the motor
will cut-out frequently which may
damage the hood.
The globes are burnt out.
The globes are loose.
Change the light globes.
Tighten the light globes.
Leaf is damaged.
Replace the leaf.
The body or motor not
secured properly.
Secure the motor tightly or fix the
body tightly, respectively.
Height/Max Height
Extraction/ Max Air Flow
Noise When Working
56 dB(A)
Rated Voltage
Max Rated Inputs (Total power)
Australian Standards
This product has been designed and manufactured to comply with all relevant Australian and New
Zealand Standards.
AS/NZS 60335.1 General Requirements for Domestic Electrical Appliances
AS/NZS 60335.2.6 Specific Requirements for Domestic Electrical Cooking Appliances
This appliance is SAA certified
Installation of the appliance must be only be undertaken by a licenced electrician who can provide
a compliance certificate.
This appliance is intended for domestic use only.
Download PDF