Fast Track Troubleshooting
Model: WF210ANW/XAA
Please Note: There are
Serial # changes on this
model, verify you are ordering the correct parts for the
Serial # you are servicing
by reviewing Bulletins.
IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
Quick Test Mode:
Publication # tsWF210 Revision Date 08/12/2010
Service Mode:
To enter press Spin, Soil, & Power
simultaneously with the power off.
This mode allows more detailed operation tests and
troubleshooting, to enter press Signal & Extra Rinse
simultaneously with the power on.
1. All LED’s light up and the washer beeps as it
enters the Quick Test Mode.
While in Service Mode (the Service Mode can be entered
while the unit is in a wash cycle) the following tests can
be performed:
2. The unit displays the software version.
3. After the displaying the software version, turn
Jog dial CCW until version disappears.
Press Spin to test Door Lock/Unlock circuit.
Press Temp Key (with door locked) to cycle through
the Water Valves circuit test in this order: Cold Main,
Bleach, Hot, then off.
Press Soil Key to test the Heater
Press Signal Key to test the Pump
Spin Only option:
Power on, Press and hold Spin until display changes.
Press Spin to select spin time.
Press Start/Pause to start cycle, Normal Cycle 10/12
minutes, Heavy Duty Cycle 11/13 minutes, Delicate
Cycle 8 minute. Spin speed varies with cycle.
EEPROM Clear Check
Power off, Press Delay Start, Signal and Power Key at
the same time. Good = Goo Fail = FAI
All memory will be cleared, including Fault Codes
This should be done when a new Main PCB is installed
Fabric Softener Dispenser Test:
Start Rinse and Spin Cycle. After fill is completed
remove detergent drawer, place towel below opening
and within 3 minutes the dispenser will activate
Quick Spin Test = Delay Start & Temp: This
accelerates the drum motor from 0 to maximum RPM over a few
minutes. Press the Start/Pause button during the test to hold
its spinning speed up to 10 min. before going back to Quick
Spin Test Mode, return to spin with Delay Start &
Temp.Cycle Count = Press the Signal button to see how
many times the unit was used
Soft Ware # = Press the Soil Level button to see the software
version information
Fault Code Test = Press the Spin button to view the stored
fault codes – then turn Dial to view error codes (Push Start/
Pause while the code is displayed to view the number of cycles since the error occurred, push Start/Pause again to get
back to faults)
Peripheral (Main PCB) input Tests, enter Service Mode &
press Extra Rinse.
1. Turn the Dial CCW to Normal, Temperature will be displayed in Celsius.
2. Turn the Dial CCW to Heavy Duty, Temperature will be displayed in Fahrenheit .
3. Turn the Dial CCW to Perm Press, The door switch status
will be displayed (CL if Closed, OP if Open).
4. Turn the Dial CCW to Sanitize, The door lock Switch status
will be displayed (UL if unlocked, LO if locked).
5. Turn the Dial so that the Rinse+Spin is turned on. Next,
press the Start/Pause Key. The Water Frequency will be displayed.
1
RY1
2
Washer Connector Checks WF210
CN2
1 AC Pwr (Wht)
3 AC Pwr L (Blu)
RY1 Main Relay
1 AC Pwr N (Wht)
2 AC Pwr (Blu)
CN3
1 Water Temp Thermistor (Wht)
2 Water Temp Thermistor Gnd. (Org)
3 Water Level Sensor (Vio)
4 Water Level Sensor (Pnk)
Water Level Sensor Check
Voltage: Connector CN 3 Pin 4 (Pink) and CN3 Pin
2 (Orange) And Connector CN 3 Pin 3 (Violet) and
CN3 Pin 2 (Orange)
CN5
1 Main Valve (Blu)
2 Hot Valve (Red)
3 Bleach Valve (Pnk)
4 Drain Pump (Gry)
6 Door Lock (Wht)
Connector CN8 Pin 4 (Orange) and Pin 2 (Red)
additionally Pin 4 (Orange) and Pin 3 (blue)
Motor Check
Connector CN9 Pin 1 (Blue), Pin 2 (White) and Pin
3 (Red)
CN
PCB Sub (Display)
Test 1
Operating voltage at no water in the
drum-2.5VDC
Test 2
Operating Resistance (Power
off)
Pin 8 (Pink) and Pin 7 (Violet)
22- 24Ω
Resistance: Connector CN 3 Pin 8 (Pink) and CN3
Pin 7 (Violet)
Hall Sensor Check
CN8 (Hull Sensor)
1 +5 vdc (Pnk)
2 Sensor Signal (Red)
3 Sensor Signal (Blu)
4 Ground (Org)
CN1
1 Motor Pwr U Phase (Blu)
2 Motor Pwr V Phase (Wht)
3 Motor Pwr W Phase (Red)
Test 1
Manually spin the drum to see the voltage change, Power On. 0Vdc or
3.75Vdc
Test 2
N/A
Test 1
Power Off 11.5Ω across Pins 1-2,
Pins 1-3, & Pins 2-3
Test 2
N/A
3
Test 1
Door Lock Check
Connector CN Pin 3 (Blk) and RY1 Pin 2 (Blue)
When Door is Unlocked 6VAC
When Door is Locked 0VAC
N/A
Test 1
Door Switch Check
Connector CN5 Pin 6 (Wht) and RY1 Pin 2(Blu)
Test 2
48Ω Door Closed, ∞Ω Door Open
Test 1
A/C Power Check
Connector CN 2 Pin 1 (Blu) and RY1 Pin 1 (Wht)
Connector CN 2 Pin 1 (Blu) and RY1 Pin 2 (Blu)
Power Off 120VAC
Power Off 0VAC - Power On 120VAC
Connector CN5 Pin 4 (Gry) and RY1 Pin 2 (Blu)
Error Mode
LED
N/A
Test 2
120VAC with the pump On and 0VAC
with the pump off
Power Off, the resistance should be
14Ω
Test 1
Test 2
120VAC with the Valve On and 0VAC
with the Valve off
Power Off, valve resistance is from
1202Ω - 1245Ω
Water Valve Check
Connector CN2 Pin (Blu) to CN5 Pin 3 (Pink), Pin
2 (Red) , Pin 1 (Blue)
Test 2
Test 1
Drain Motor Check
Error Type
Test 2
Details
LCD
Water Level Sensor
LE
8
Check the Hose where the sensor is connected, may be loose,
pinched, damaged or clogged. Also check the sensor it may be
disconnected or defective. The Main PCB may also be defective
Water Level Sensor
1E
Water Level Sensor Trouble, Signal out of range
Motor Drive Error or
Hall Sensor error
3E
E3
bE
25
Check the motor drive connector, it may be loose. The hall sensor
may be disconnected, loose or damaged . Check for a foreign object inside the motor or motor damage. The stator might be loose
or damaged. The drum might be overloaded from too many
clothes or the relay or PCB might be defective.
Check the water valve wiring harness.
Water Supply
Error
nF
3
Check whether the water supply valve is clogged with foreign material and whether water is supplied properly.
Check for reversed fill hoses
Check water temperature, if sensed as higher than 50 ˚C in the
Wool or Lingerie cycle it will create error.
Check the relays, if they operate correctly replace the Main PCB.
Fill Hoses Reversed
nF1
Correct Hot/Cold hose connections
System Error
SF1
SF2
SF3
Replace PCB
4
Error Type
Error Mode
LED
Details
LCD
Check for Foreign material entering the pump or hoses.
Drain Error
nD
1
Check to make sure the wiring harness is connected properly.
Check the water pump terminal .
Check for freezing
Power Error
2E
91
92
Make sure to check the operating voltage. (An error occurs when
under or over voltage is supplied.) Check whether a plug receptacle is used. When the connecting wires are too small (extension
cord use), a momentary low voltage may drop up to 10 V
Main PBA fault (sometimes)
PF
Momentary Power Failure
AE
Check the wire connections and terminal contacts between the sub
and main PBAs.
Communication Error
Check for disconnected wires.
Check whether the sub PCB is short circuited because of moisture.
If the main PCB’s communication circuit is faulty, replace it.
EEPROM
Fault.
11
Switch Error
E2
15
(Main Relay
Error)
Go to “EEPROM Clear Mode” If display shows “FAiL”, Replace Machine Control Board
Check whether either the Power switch or a tact switch (any button)
is stuck down.
Check whether the service PBA holding screws are fastened too
tight pinching the contacts
If the main PBA switching IC on/off error has occurred, replace the
main PBA.
SR
The “E2” error occurs if the main relay connections are incorrect.
Check the connections. If there is no error in the connections, replace the main PBA
dS
22
(Before
operation)
Door Error
dL
18
(During
operation)
LO
2
Check the door switch and latch alignment .
Check the latch for damage
Check the wiring harness to the latch.
Check the door switch. Replace if faulty.
Check the main PBA door sensing circuit. Replace if faulty.
Finally verify he operation of the Main PCB
(Unlock
Fail)
FL
4
(Lock Fail)
5
Error Type
Error Mode
LED
Heater Error
Details
LCD
This can be a short or a wire disconnected to the heater circuit. This
can also be problem with the tub contacting the heater or if the water in the tub is frozen or there is no water. The error is triggered by
temperatures above 145C. If the heater has no error, this occurs
because of a PBA relay malfunction. Check the wiring harness to
the heater.
Hr
36
(Heater
Relay)
An Hr error occurs if the steam heater, is faulty, replace it.
Overflow error
9E1
EMC Filter issue or a noise spike from an external device
OE
1E
Water is supplied continually because the water level detection
does not work. - Verify the drain is working properly, the water level
detection does not work and water is supplied continually. Verify the
water valves shut off fully. Finally check the water level sensor.
29
The washing heater temperature sensor in the tub has an error.
Check the connections for the washing heater temperature sensor
connector.
Temperature
Sensor Error
Unbalance
Error
Check the type of laundry. Check whether it may cause an unbalanced situation.- Educate the consumer in this case, to press
pause, reposition the load or remove a few items. Press start to
continue and complete the wash cycle.
dC
10
Silver Care Kit 7E
(Silver Care
PCB) Failure.
Mems or Har-
Foaming
Detected
Check Silver Care PCB ,Main PCB & Wire-harness
8E
Check MEMS PCB ,Main PCB & Wire-harness
This occurs when too much foaming is detected. It is also displayed
while foaming is removed. When the removal is finished, the normal
cycle proceeds. (This is one of the normal operations. It is an error
for preventing non-sensing faults.)
SUdS
Sd
SUd
Check whether the washing machine is level to the floor with respect to the original position of the washing machine prior
to service. Doing this now will reduce the need for a redo call and customer dissatisfaction.
✔ Vibrations can shorten the lifetime of the product.
Location considerations
Do not install your washer in areas
where water may freeze, since
your washer will always maintain
some water in its water valve,
pump, and hose areas. This can
cause damage the belts, the
pump, hoses and other components. Operating temperature
should be above 60°F/16°C.
When installing a washer and dryer on the first, or second
floor, do not exceed this leg adjustment height for stability.
6
Water valve connections for the Detergent Drawer
When using non-HE detergents, or using too much detergent for the water hardness and soil level of the clothing,
over sudsing will occur. When this happens there will be
leaks out of the detergent drawer and door. Please advise
consumer of proper detergent usage.
It is normal for some water to remain in Detergent Drawer after it completes washing.
Bleach is usually flushed out into the tub at the
beginning of the washing. Also, its compartment is washed again during the following
rinse cycle, removing any remnants.
A
B
Items Packed With Washer
BOLT-SPANER (10-13mm Wrench) DC60-40146A
ASSY HOSE WATER Cold DC97-15648A
ASSY HOSE WATER Hot DC97-15648B
CAP-FIXER DC67-00307A
HOSE-HANGER DC62-10278A
To unlock the door if washer is stuck in the door
locked mode.
Remove top, remove console, remove screws for
front panel, pull panel forward.
Picture “A” pull bottom of plastic cover away from
front until it pops off.
Picture “B” pull down on plastic lever to release
lock.
Remove lock ass’y to replace plastic cover.
7
Download PDF

advertising