Keurig® Vue® V600 Brewer
Use & Care Guide
IMPORTANT SAFEGUARDS
Safe Operation & Use
When using electrical appliances, basic safety precautions should
be followed, including the following:
1.Read all instructions before using.
2.Do not touch hot surfaces. Use
handles and knobs when available.
3.This appliance must be properly
installed and located in accordance
with these instructions before it
is used.
4.The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5.Do not place on or near a hot gas or
electric burner, or in a heated oven.
6.Do not use outdoors.
7.To protect against fire, electric shock
and injury do not immerse cords,
plugs, or the appliance in water or
any other liquid.
8.Do not overfill the Water Reservoir
with water.
9.Use only water in this appliance!
Do not put any other liquids or
foods in the Water Reservoir
except as instructed in the Cleaning
Instructions in this guide.
13.Do not let the cord hang over the edge
of the table or counter, or touch hot
surfaces.
14.To disconnect, press the Power
Button on the brewer to ‘OFF’ status
and then remove the plug from the
wall outlet.
15.Close supervision is necessary when
any appliance is used by or near
children.
16.Do not lift the Handle to open the
brewer while brewing is in progress.
17.Always keep the Water Reservoir Lid
on the Water Reservoir unless you are
refilling it.
18.This appliance is equipped with a
power cord having a grounding wire
with a grounding plug. The appliance
must be grounded using a 3-hole
properly grounded outlet. In the
event of an electrical short circuit,
grounding reduces the risk
of electrical shock.
19.If the outlet is a standard 2-prong
wall outlet, it is your personal
responsibility and obligation to have
it replaced with a properly grounded
10.Turn off and unplug the brewer before
3-prong wall outlet.
cleaning or maintenance. Allow to cool
before putting on or taking off parts
20.Do not, under any circumstances,
cut or remove the third (ground)
and before cleaning the appliance.
prong from the power cord or use
11.For best operation, plug the appliance
an adapter.
into its own electrical outlet on a
dedicated circuit to prevent flickering 21.Consult a qualified electrician if
the grounding instructions are not
of lights, blowing of fuses or tripping
a circuit breaker.
completely understood, or if doubt
exists as to whether the appliance
12.Do not operate any appliance with
is properly grounded.
a damaged cord or plug or after
the appliance malfunctions or is
22.Do not use the appliance for
damaged in any manner. Contact
other than its intended use.
Keurig Customer Service to report
any malfunction of or damage to
the brewer.
2
CAUTION: There is extremely hot water in the Vue® pack Holder
during the brew process. To avoid risk of injury, do not lift the
Handle or remove the Brew Head during the brewing process.
Do not remove or puncture the lid of the Vue® pack prior to
brewing. After brewing, use caution when removing the Vue®
pack, as it will be hot.
Please always keep the brewer in its upright position to avoid
potential injury and/or damage to your brewer.
SHORT CORD INSTRUCTIONS: A short power supply cord is
provided to reduce the risk of becoming entangled in or tripping
over a longer cord.
Longer detachable power-supply or extension cords are available
and may be used if care is exercised in their use.
If an extension cord is used, (1) the marked electrical rating of
the cord set or extension cord should be at least as great as the
electrical rating of the appliance; (2) the cord should be arranged
so that it will not drape over the counter top or tabletop where it can
be pulled on by children or tripped over unintentionally; and (3) the
extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
Save These Instructions.
WARNING
THIS PRODUCT CONTAINS CHEMICALS, INCLUDING
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
!
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM
COVER. NO USER SERVICEABLE PARTS ARE
INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED
SERVICE PERSONNEL ONLY.
WARNING TO USERS AND PARENTS: DO NOT permit children to use
brewer unless there is adult supervision. Brewer dispenses very hot water.
3
Table of Contents
Section 1 Brewer Overview
6
Section 2 Preparing Your Brewer
8
Section 3 Using Your Brewer
9
Section 4 Setting the Time & Temperature
17
Section 5 Caring For Your Brewer
20
Section 6 Recycling the Vue® Pack’s Plastic Cup
22
Section 7 Troubleshooting
23
Section 8 Warranty
24
Record Your Brewer Serial Number Above
The serial number can be found on the bottom of the brewer
box and on the left side of the brewer once the Water Reservoir
has been removed. Removing the serial number label from the
brewer will void warranty.
4
5
SECTION 1
Brewer Overview
A
B
A “BREW” Button
C
Flashing indicates brewer is ready to brew
B Power Button
C Touchscreen
J
D
D Handle
E Brew Head
F Power Cord
G Drip Tray
E
I
H Adjustable Drip Tray Plate
I Water Reservoir
J Water Reservoir Lid
F
H
G
The Keurig® Vue® brewer is not for
use with K-Cup® packs.
6
7
SECTION 2
SECTION 3
Preparing Your Brewer
Using Your Brewer
Step 1
Remove all adhesive tape and labels from brewer. Lift
Handle and remove shipping disc. Lower Handle before
filling Water Reservoir or powering on brewer. Behind the
brewer is a convenient compartment to hold the Power
Cord for storage.
Plug cord into grounded outlet.
Step 1
If brewer has been exposed to temperatures below freezing, allow
brewer at least two hours to reach room temperature before
brewing. A frozen or extremely cold brewer will not operate.
Step 2
Carefully remove Water Reservoir Lid. Remove the Water
Reservoir by lifting up and away from the brewer.
Brew what you love, the way you love it.
The new Keurig® Vue® brewer, with Custom Brew Technology®, gives you total
control to brew your way: stronger, bigger, hotter and with more choices than
ever before. Enjoying a perfect cup of coffee has never been easier.
So what are you in the mood for today?
How to Use the Vue® Brewer Touchscreen
Rinse Water Reservoir with fresh water. Return Water
Reservoir to brewer. Fill the Water Reservoir to the
“MAX FILL” line. Bottled or filtered water is recommended.
Place Lid on Water Reservoir.
Step 2
See page 16 for options for how to add water to the
Water Reservoir.
Back Button
Step 3
Beverage
Category
Place a 10 oz. mug toward the back of the Drip Tray and
press the Power Button.
Beverage Type
The Handle should be in the lowered position.
Strength Selection
(Coffee Only)
Step 3
Step 4
When the brewer is first turned on, the Touchscreen
will indicate “Not Ready” as the brewer heats the water.
Wait until the Touchscreen indicates “Ready”
(about four minutes).
Step 4
8
Brew Status
If there is not enough water in the Water Reservoir, the
Touchscreen will indicate “Add Water” and the Water Reservoir
light will flash.
Lift and lower the Handle, then press the flashing “BREW”
Button. Your brewer will dispense 8 oz. of hot water into
your mug. Once complete, discard the hot water. You are
ready for your first brew!
Beverage Size
Selection
Available Range
Coffee Tea/Other Hot Cocoa 4 - 18 oz.
6 - 12 oz.
6 - 10 oz.
The screen above shows all possible menu selections for illustration purposes only.
When in use, your Touchscreen will display only selectable actions.
9
SECTION 3
SECTION 3
Using Your Brewer
Using Your Brewer
Brewing Coffee, Tea,
Hot Cocoa and Hot Apple Cider
Choose Vue® Pack
Make sure your Vue® pack
features the Coffee & Tea Icon.
Lift the Handle, insert
the Vue® pack into the Holder
and lower the Handle.
Select Beverage Type & Size
After you lower the Handle, the Touchscreen will display
as pictured with the “Coffee” button, “Regular” and 8 oz.
beverage size.
To make coffee, choose your strength and size. If you prefer a
stronger brew, select “Strong.” Then select your beverage size
by using the + and - buttons at the bottom of the Touchscreen.
To make tea, hot cocoa or other beverages, such as hot cider,
press the “Coffee & Tea” button.
Available Range
Coffee Tea/Other Hot Cocoa 4 - 18 oz.
6 - 12 oz.
6 - 10 oz.
For Smaller Mugs
Lift the Adjustable Drip Tray Plate and rotate a
third of a turn until it drops into place. Make sure it
is seated securely in the elevated position before
placing your cup on it.
For Travel Mugs
If needed, remove the Drip Tray to allow your mug to fit.
For larger brew sizes, we recommend using Travel Mug
Vue® packs, which are designed to deliver a great tasting
travel mug-sized brew.
Follow the instructions for brewing a coffee (refer to page 10),
but select one of the larger size options (12 oz. to 18 oz.).
Note that Travel Mug beverages have been optimized at
14 oz. and 16 oz. settings. Enjoy your travel mug brew!
Once selected, the screen will display as pictured with the
“Coffee,” “Tea/Other” and “Hot Cocoa” buttons. Choose your
selected beverage. For hot cider, select “Tea/Other.” Select
your beverage size using the + and - buttons at the bottom
of the Touchscreen.
Press
& Enjoy!
The Vue ® pack will be hot after brewing. Use caution when removing.
Allow it to cool completely before handling.
10
Immediately after using a hot cocoa pack, we recommend running a
cleansing brew. See page 15 for directions.
14
16
18
12oz
14oz
16oz
18oz
oz
oz
oz
oz
14oz
16oz
18oz
oz
4oz
6oz
8oz
10oz
Do not remove mug or lift the Handle until “Enjoy!”
disappears from Touchscreen.
Remove the Vue ® pack after brewing is complete.
12
4oz
6oz
8oz
10oz
12oz
oz
oz
oz
Available Sizes
11
6o
6o
SECTION 3
SECTION 3
Using Your Brewer
Using Your Brewer
Brewing Café Beverages
Requires 2 packs
Step 1
Step 2
Choose Café
Step 1 Pack
Choose Café
Step 2 Pack
Make sure your Vue® pack
features the Café Icon.
Insert the Vue® pack into the
Holder and lower the Handle.
Lift the Handle, insert
the Vue® pack into the Holder
and lower the Handle.
Select “Café”
Select Beverage Type & Size
Press the “Café” button, then the Touchscreen
will display as pictured. Froth is available in the 4 oz.
brew size only.
After you insert the second Vue® pack and lower
the Handle, the Touchscreen will display
as pictured.
Coffee: For a coffee-based café beverage, press the
“Coffee Step 2” button. “Strong” is the default setting for café
beverages. De-select if desired.
Tea: For a tea-based café beverage, press “Tea/Other
Step 2” button.
Press
After the froth is prepared, lift the Handle and carefully remove
the pack. The Touchscreen will display as pictured on
page 13. Proceed to Step 2.
The Vue ® pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
Select your café beverage size using the + and - buttons at
the bottom of the Touchscreen. The amount you select will be
ADDED to the existing 4 oz. of froth.
If a selection is not made within 60 seconds, the brewer will
return to the default screen. To complete the brew successfully,
follow the brewing instructions on page 10 and brew
“Coffee” 4 oz. “Strong” (for a coffee-based café beverage) or
“Tea/Other” 4 oz. (for a tea-based café beverage).
Press
4oz
6oz
8oz
4oz
6oz
8oz
Available Sizes
& Enjoy!
Do not remove mug or lift the Handle until “Enjoy!”
disappears from Touchscreen.
Remove the Vue ® pack after brewing is complete.
12
The Vue ® pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
13
SECTION 3
SECTION 3
Using Your Brewer
Using Your Brewer
Brewing Over Ice
What is a Cleansing Brew?
After brewing certain Vue® pack varieties such as hot
cocoa, iced tea or a café beverage, we recommend
performing a cleansing brew as follows:
Prepare Your Cup
Fill a 16 oz. plastic cup with ice. Do not use glass.
Remove the Drip Tray if necessary and place cup
under the Brew Head.
Choose Vue® Pack
Make sure your Vue® pack
features the Brew Over Ice Icon.
Lift the Handle, insert
the Vue® pack into the Holder
and lower the Handle.
Step 1 Take a used Vue® pack and peel off the lid. Discard
the lid and any filter which adheres to it. Ensure the
empty Vue® pack cup is clean.
Step 1
Step 2Place the EMPTY Vue® pack cup in the brewer and
place a mug on the Drip Tray.
Step 3Lower the Handle, then press “BREW.” The brewer
will dispense 8 oz. of hot water into your mug.
Once complete, discard the water and carefully
remove the Vue® pack cup. The cleansing is
complete.
Stopping the Brewing Process
If you need to stop the brewing process after it has started,
press and release the Power Button to turn the brewer off.
The beverage flow will stop and the brewer will shut off.
Select Beverage Type & Size
Select the “Brew Over Ice” button. The Touchscreen
will display as pictured.
Select the desired beverage type.
Select your beverage size using the + and - buttons
at the bottom of the Touchscreen.
* Available sizes for Iced Coffee and Iced Tea/Other
are 6 oz., 8 oz. and 10 oz.
* Available sizes for Iced Café are 6 oz. and 8 oz.
The Vue ® pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
When turning the brewer back on, place an empty mug
toward the back of the Drip Tray and press the Power
Button. Since the previous brew was interrupted, some
water may drip into the mug during preheating.
We recommend that you perform a cleansing brew before
brewing your next beverage (see above). If this is not done,
the brewer may deliver an additional amount of water for
your next beverage.
Step 3
Dispensing Hot Water
Available Sizes*
Press
& Enjoy!
Do not remove mug or lift the Handle until “Enjoy!”
disappears from Touchscreen.
Remove the Vue ® pack after brewing is complete.
14
Step 2
The Vue ® pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
If you need hot water for cooking (instant soup or oatmeal,
for example), place a cup or bowl below the Brew Head.
Place your cup or bowl toward the back of the Drip Tray.
Lift and lower the Handle WITHOUT inserting a Vue® pack.
Select “Coffee” (do not select “Strong”) and your desired cup
size and then press “BREW.” The brewer will dispense hot
water into your cup or bowl.
15
SECTION 3
SECTION 4
Using Your Brewer
Setting the Time & Temperature
Adding Water
Accessing the Settings Menu
When the water supply is low, the Touchscreen will display
as pictured and the Water Reservoir light will flash.
When the brewer is on and not brewing, the “Menu”
option will appear on the Touchscreen. Follow the
steps below to access the settings menu. Press and
hold the “Menu” button to access. Use the “Menu”
button to tab through the setting options.
Bottled or filtered water is recommended.
Do not remove the Water Reservoir during the brewing process.
There are two options for filling the Water Reservoir:
Setting the Clock
Step 1
Option 1
Remove the Water Reservoir Lid and pour water directly
into the Water Reservoir. Replace the Lid.
Touch the “Menu” button on the Touchscreen.
Step 2
The “H” will flash, indicating you are programming the hours.
Use the + and - buttons to change the hours. Press the
“Menu” button again to access the minutes. Use the + and buttons to set the minutes. The clock is on a 11h setting and
will switch to PM once the 11h mark is passed.
Step 3
Option 2
Once the clock is set, touch the “Menu” button to save your
settings. The screen will move to the next programmable
setting (Auto Off).
You may also remove the Water Reservoir from
the brewer to fill it. Replace the Lid and return
the filled Water Reservoir to the brewer.
Do not remove the Water Reservoir during the brewing process.
Programming the “Auto Off”
Feature
When brewing at 14 oz., 16 oz. and 18 oz. sizes, if the brewer
senses the water level is low, the brewing process will stop until
the Water Reservoir is refilled. Once enough water has been
added, the brewing process will resume. Ensure that your mug is
still on the Drip Tray.
16
You can program the brewer to automatically turn off after a
certain period of time after the last brew. This feature can be
used as an energy saver.
In “Auto Off” programming mode, use the + and - buttons
to change the hours the brewer will remain on after the last
brew. For example, if you select “2,” the brewer will turn off
two hours after the last brew. Use the + and - buttons to
scroll to “Off” to deactivate the “Auto Off” feature.
Once the feature is set, press the “Menu” button to save your
settings. The screen will move to the next programmable
setting (Set On Time see page 18).
17
SECTION 4
SECTION 4
Setting the Time & Temperature
Programming the
“On Time” Feature
By programming your brewer to turn on each morning, you
will never have to wait for the brewer to warm up to brew
your first cup. It takes the brewer approximately 4 minutes
to warm up from room temperature.
The clock must be set in order for the on/off feature to operate
correctly. See page 17 for directions.
If power is interrupted to the brewer by unplugging it, or if power
is lost, follow the procedure on page 17 to set the clock.
In “On Time” programming mode, the “H” will flash,
indicating you are programming the hours. Use the +
and - buttons to set the hours. Press the “Menu” button
again to access the minutes. Use the + and - buttons to set
the minutes. The clock is on a 11h setting and will switch to
PM once the 11h mark is passed.
Setting the Time & Temperature
Setting the Brew Temperature
The brewer has a preset temperature of 192° F. You can
adjust the temperature up or down in 1-degree increments
within the brewer range (187° – 197° F). Once set, your
beverages will be brewed at the selected temperature.
At high altitudes, if boiling occurs, use the temperature
adjustment to lower the temperature so that boiling does
not occur.
Here is how to set the brew temperature:
Step 1
In “Set Brew Temp” mode, Use the + and - buttons to
change the temperature.
Step 2
Press the “Menu” button to save your setting and return
to the main screen.
Once the “On Time” clock is set, press the “Menu” button
to save your settings. The screen will move to the next
programmable setting (Set Off Time).
Programming the
“Off Time” Feature
Programming your brewer to turn off each evening will
ensure the brewer turns off each night when it will not
be used.
Viewing Your Presets
Your settings will appear in the main menu. To review your
current settings, touch the “Menu” button. You can change
the settings at any time. Simply enter through the “Menu”
to re-set any options using the directions in this section.
If power is interrupted to the brewer by unplugging it, or if power
is lost, follow the procedure on page 17 to set the clock.
The clock must be set in order to program the on/off feature.
See page 17 for directions.
In “Off Time” programming mode, the “H” will flash,
indicating you are programming the hours. Use the
+ and - buttons to set the hours. Press the “Menu” button
again to access the minutes. Use the + and - buttons to set
the minutes. The clock is on a 11h setting and will switch
to PM once the 11h mark is passed.
18
Once the “Off Time” clock is set, press the “Menu” button
to save your settings. The screen will move to the next
programmable setting (Setting the Brew Temperature).
19
SECTION 5
SECTION 5
Caring For Your Brewer
Caring For Your Brewer
Cleaning & Maintenance
Cleaning External Parts
Cleaning of the brewer’s external parts is recommended
one to two times per month. Never immerse the
brewer in water or other liquids. The Housing and other
external parts may be cleaned with a soapy, damp,
non-abrasive cloth.
The Drip Tray can accumulate up to 13 oz. of overflow.
The Drip Tray and the Adjustable Drip Tray Plate should be
periodically inspected and rinsed clean. To remove the Drip
Tray, simply slide it toward you, keeping it level at all times to
avoid spilling. The Drip Tray should be cleaned with a soapy,
damp, non-abrasive cloth. The Drip Tray and Adjustable
Drip Tray Plate should not be put in the dishwasher.
1
2
3
Cleaning The Brew HEAD
Step 1 Lift the Handle.
Step 2 Grip and press the buttons on both sides of
the Brew Head and tilt it down.
Step 3 Pull the Brew Head toward you to remove.
Carefully clean the Brew Head with a soapy, damp,
non-abrasive cloth and rinse thoroughly. The Brew
Head should not be placed in the dishwasher.
Return the Brew Head by sliding it gently back into place
until you hear a click. Lower the Handle and you are ready
to brew again.
Cleaning the Water Reservoir &
Water Reservoir Lid
The Water Reservoir and Lid should not be put
into the dishwasher. Clean them with a soapy, damp,
non-abrasive cloth and rinse thoroughly. Do not dry
the inside of the Water Reservoir with a cloth as lint
may remain.
CAUTION: Rinse the Water Reservoir thoroughly after cleaning
to ensure that no cleaners or cleaning solutions remain in this
area as they may contaminate the water supply in the brewer.
20
De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the mineral content
of the water in your area, calcium deposits or scale may build up in your brewer. Scale
is non-toxic, but left unattended, it can hinder brewer performance. De-scaling your
brewer helps maintain the heating system and other internal parts of the brewer that
come in contact with water.
The brewer should be de-scaled every three to six months to ensure optimal
performance. It is possible for calcium deposits to build up faster, making it necessary
to de-scale more often.
The de-scale process requires the brewer to stand for at least 4 hours. During this period, the
brewer should not be used to brew beverages.
Prepare
Step 1 To begin, you will need:
• At least 48 oz. of undiluted white vinegar
• A large ceramic mug, at least 10 oz. (do not use a paper cup)
• A clean, empty Vue® pack cup
Step 2 Empty the water in the Water Reservoir.
Step 3 Disable “Auto Off” and “On/Off Time” settings (refer to pages 17 and 18).
Fill & Clean
Step 1 Pour at least 48 oz. of the vinegar into the Water Reservoir.
Step 2 Place the mug on the Drip Tray Plate. Lift the Handle and insert a clean, empty
Vue® pack cup. Lower the Handle, then press “BREW.” The brewer will dispense
8 oz. of hot vinegar into your mug. Dispose of the vinegar.
Step 3 Repeat the process until “Add Water” is indicated.
Step 4 Let the brewer stand for at least 4 hours while still on.
Step 5 Discard the remaining vinegar from the Water Reservoir and rinse the Reservoir
thoroughly. Remove the empty Vue® pack cup from the brewer.
Rinse
Step 1 Ensure the Water Reservoir is filled with fresh water.
Step 2 Place a large mug on the Drip Tray Plate and run a cleansing brew. Pour the
contents of the large mug into the sink.
Step 3 Repeat the cleansing brew process until “Add Water” is indicated.
Step 4 You may need to perform additional cleansing brew cycles (refer to page 15)
if you notice any residual taste.
21
SECTION 6
SECTION 7
Recycling the Vue Pack’s Plastic Cup
Troubleshooting
®
Recycle your Vue® pack’s plastic cup wherever #5
plastic is accepted. #5 plastic may not be recyclable in
your community today, so please check locally with
your municipality or waste hauler, or visit
www.vuerecycling.com for more information about
recycling your Vue® pack’s plastic cup.
SITUATION SOLUTION
Brewer does not • Plug brewer into an independent outlet without dimmer control.
have power • Check to be sure that it is plugged in securely.
• Plug into a different outlet.
• Reset your home’s circuit breaker if necessary.
• Make sure that the Power Button has been turned on and
Touchscreen is illuminated.
Simply follow these simple steps:
Brewer will • After placing the Vue® pack in the Vue® pack Holder, make sure the
not brew Handle is pushed down securely and the Touchscreen displays the
beverage options. Select your desired beverage type on the Touchscreen
Step 1
Once brewing is complete, lift the Handle and carefully
remove the Vue® pack by holding the outer rim.
The Vue ® pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
and follow the brewing instructions in Section 3 (refer to pages 9-15).
• If the Touchscreen indicates “Add Water,” add water to the Water Reservoir
or make sure the Water Reservoir is seated properly in its base.
• If the Touchscreen indicates “Add Water” even after refilling, remove the
Water Reservoir and empty the water. Then thoroughly clean (refer to
page 20). Fill the Water Reservoir to the “MAX FILL” line and then return
it to the brewer and ensure it is seated properly in its base.
• T he Brew Head may need to be cleaned or the brewer needs to be
de-scaled (refer to pages 20 and 21).
• If you have completed the above procedure two times and this situation
Step 2
Once cool, separate the lid and filter from the cup.
Any filter will adhere to the lid.
persists, contact Customer Service at 1.866.901.BREW (2739).
Brewer brews only • Clean the Brew Head if necessary (refer to page 20).
a partial cup • T he Water Reservoir may have been removed during brewing.
Replace the Water Reservoir and perform cleansing brews
(refer to page 15) without a Vue® pack.
• De-scale the brewer (refer to page 21).
• If you have repeated the de-scale procedure on your brewer two times
and it is still only brewing a partial cup, contact Customer Service at
Step 3
Once separated, discard the lid and any attached
filter. Recycle your Vue® pack’s plastic cup wherever
#5 plastic is accepted. #5 plastic may not be recyclable
in your community today, so please check locally with
your municipality or waste hauler, or visit
www.vuerecycling.com for more information about
recycling your Vue® pack’s plastic cup.
1.866.901.BREW (2739).
Brewer shuts off or • Check to make sure that the “On/Off Time” and/or “Auto Off” settings
turns on automatically have not been set. Please refer to pages 17 and 18 for instructions.
Water Reservoir • The water level is low and a full cup cannot be brewed. Add water to
light is flashing and Water Reservoir.
the Touchscreen
• If the water level is not low, remove the Water Reservoir and empty the
indicates “Add Water”
water. Then thoroughly clean (refer to page 20). Fill the Water Reservoir to
the “MAX FILL” line and then return it to the brewer and ensure it is seated
properly in its base. Wait for the Water Reservoir light to stop flashing.
The time is not displayed • If power is interrupted to the brewer by unplugging it, or if power is lost,
on the Touchscreen follow the procedure on page 17 to set the clock.
22
23
SECTION 8
SECTION 8
Warranty
Warranty
Limited One Year Warranty
How do you obtain warranty service?
Keurig warrants that your brewer will be free of defects in materials or workmanship
under normal home use for one year from the date of purchase. It is recommended
that you fill out and return the warranty card enclosed with your brewer so that
your purchase information will be stored in our system. Keurig will, at its option,
repair or replace a defective brewer without charge upon its receipt of proof of the
date of purchase. If a replacement brewer is necessary to service this warranty, the
replacement brewer may be new or reconditioned. If a replacement brewer is sent, a
new limited one year warranty will be applied to the replacement brewer.
Keurig® brewers are high-quality appliances and, with proper care, are intended
to provide years of satisfying performance. However, should the need arise for
warranty servicing, simply call Keurig Customer Service at our toll free phone number
1.866.901.BREW (2739). Please do not return your brewer for servicing without first
speaking to Keurig Customer Service to obtain an Authorization to Return number
(ATR). Keurig® brewers returned without an ATR number will be returned to the sender
without servicing.
This warranty only applies to brewers operated in the United States and Canada. This
warranty gives you specific legal rights, and you may also have other rights that vary
from state to state and, in the case of Canada, from province to province.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)
Only the use of Keurig Brewed® Vue® brand packs and accessories will guarantee the
proper functioning and lifetime of your Keurig® brewer. Any damage to or malfunction
of your brewer resulting from the use of non Keurig Brewed® Vue® brand packs and
accessories may not be covered by this warranty or may result in a service fee if the
damage or malfunction is determined to be caused by such use.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES
SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS
AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF
FORESEEABLE. Some states or provinces do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitation or exclusion may not
apply to you depending on the state or province of purchase.
Nor does this warranty cover damages caused by use of non Keurig Brewed® Vue®
brand packs or accessories, services performed by anyone other than Keurig or its
authorized service providers, use of parts other than genuine Keurig parts, or external
causes such as abuse, misuse, inappropriate power supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY,
WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY
DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR V600 BREWER,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such
implied warranties or limitations on how long an implied warranty lasts, so the above
limitation may not apply to you depending on the state or the province of purchase.
24
25
Notes
26
27
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
Keurig, Incorporated is a wholly-owned subsidiary
of Green Mountain
Coffee Roasters, Inc.
For Household Use Only
Made in China.
Printed in China.
© 2013 Keurig, Incorporated
All rights reserved
www.keurig.com | 1.866.901.BREW
P/N 60-201386-000 Rev C 02/13