Important Battery lnformation
Instructions for PREMISE PRO
Digital Surveillance Camera
- Only use Alkaline or Lithium batteries. We recommend the use of Energizer batteries.
- Do not mix old and new batteries. Always replace ALL the batteries at the same time.
- When the camera is not in use, please remove the batteries.
Moultrie Limited Warranty
This product has been thoroughly tested and inspected before shipment. It is guaranteed from
defects in material and workmanship from the date of purchase for 2 years. Under this limited
guarantee we agree to replace or repair free of charge any part or parts which have been found to
be defective in original material or workmanship. Should you require in-warranty service, call our
Customer Service Department. If your problem cannot be addressed over the telephone, we may
need you to send us your defective product plus proof of purchase.
You must register your camera at www.moultriefeeders.com/warranty to activate
your 2-year warranty.
THANK YOU for your purchase of the PREMISE PRO Digital Surveillance Camera. Please read
this booklet before using the unit. If you should have any questions about this product or any
other Moultrie product, please contact us using the information on the back of this booklet.
Please register your camera at www.moultriefeeders.com/warranty to activate your
2-year warranty.
A
CAMERA OVERVIEW
FRONT VIEW
Troubleshooting
Please visit www.moultriefeeders.com/contact-us for troubleshooting and helpful tips.
Infrared LED Flash
Motion Sensor
Returns and Repairs
Please visit http://www.moultriefeeders.com/return-policy and complete the form or our
Service Department will gladly answer any questions you have. Call 800-653-3334,
Monday - Friday, 8:00 AM to 5:00 PM CST.
Camera Lens
LCD Display
FCC Statements
SD Card Slot
Moultrie Products
MCS-13070
Status Indicator
Premise Pro
Menu Button
ON
AIM
OFF
Note: changes and modifications not expressly approved by the party responsible could void the user’s authority to operate this device.
OK/Select Button
Navigation Buttons
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Push Button Release for battery compartment
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: This device complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- lncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
BOTTOM VIEW
External Power Port
USB Port
www.moultriefeeders.com
PRADCO Outdoor Brands • 3280 Highway 31, Ste B • Calera, AL 35040
11232015 / MCS-13070
1/4” 20 Mount
PREMISE PRO Digital Surveillance Camera
Page 1
A
CAMERA OVERVIEW (cont.)
OFF / AIM / ON
Aim - When Aim is ON and the PIR sensor detects motion, the red LED on the front of the camera will
come on for 1 second and then shut off.
MENU BUTTON
The Menu Button selects Camera Setup or Main Screen. When camera mode is selected, the LEFT and
RIGHT buttons navigate through the menu options. The Menu Button is also used to wake-up the
camera and turn on the display when the camera is in power saving (or sleep) mode.
OK, UP/DOWN and LEFT/RIGHT BUTTONS
The OK button selects the item to be changed. The UP/DOWN and LEFT/RIGHT buttons are used
to step through and modify the menu options. Pressing the OK button again, selects the option
indicated on the display. The OK button is also used to manually take a picture.
BATTERY COMPARTMENT
The camera is powered by eight (8) AA alkaline or lithium batteries. Push the battery compartment
release button to eject the battery tray. Install batteries as indicated on the engravings on the battery
tray, taking care to note the correct polarity.
See Important Battery Information section on the back page of this manual.
SD CARD SLOT
Accepts up to a 32GB SD Card (Class 4 or higher) for photo and video storage.
NOTE: A Class 4 or higher SD Card must be installed for the camera to operate (sold separately).
USB PORT
Download still pictures and video onto your computer by connecting a micro-B to USB cable
(not included) to the USB port.
EXTERNAL POWER PORT
Accepts the Moultrie PowerPanel, Moultrie AC Adapter or Moultrie Battery Box accessories
(sold separately) only. Refer to www.moultriefeeders.com for more information.
NOTE: The use of any other power source will void your warranty and possibly harm your camera.
Page 2
PREMISE PRO Digital Surveillance Camera
H
MOULTRIE ACCESSORIES (Sold Separately)
Moultrie Mobile® Compatibility
Your camera is compatible with our Moultrie Mobile®
cellular service when combined with the
Field Modem MV1.
Please visit www.moultriemobile.com
for more information.
NOTE: Camera firmware update may be required
for full Moultrie Mobile functionality.
Using the Moultrie AC Adapter
Keep your Moultrie camera running in the field with
the constant power of an AC adapter. Plug into a
standard 110-240VAC 50-60Hz electrical outlet and
then connect to the External Power Port on your
Moultrie camera.
Note: Leave internal batteries in the camera during
use. In the event of power loss to the outlet into which
the AC adapter is plugged, the internal batteries will
keep your camera running.
Using the Moultrie Camera Power Panel
Place near the tree where the camera is mounted.
Place for best exposure to sun. To attach to a
tripod secure the power panel to the tripod
angled upward for best exposure. Plug the power
panel to the Power Panel Plug. This will extend the
life of your camera in the field.
Note: Leave internal batteries in the camera
during use. The Camera Power Panel needs
4 hours of sunlight to fully power the camera.
Using the Moultrie Battery Box
Extend the field life of your Moultrie camera with a
long-lasting, rechargeable external power source.
Place near the tree where the camera is mounted.
Plug the Battery Box to the Power Panel Plug.
This will extend the life of your camera in the field.
PREMISE PRO Digital Surveillance Camera
Page 11
G
VIEWING YOUR IMAGES
There are a number of ways for you download and view
the pictures, videos in the field or at another location.
Removing the SD Card
To remove the SD Memory Card, open the camera cover
and push gently on the SD card and it will pop out slightly
allowing you to remove it. Load the SD card into the
player or card reader to view or move stored images to
another location.
Important
Make sure that the camera is in the OFF position before
removing SD card.
ln the Field
You can download the pictures, videos, and time lapse
pictures with the aid of external devices. To download,
use an external player or card reader that is
supported by 12V DC or Mini USB Jack.
QUICK START INSTRUCTIONS
Use the steps below as a guide to quickly set up your camera so it will function using the factory
default settings.
STEP 1
Open camera cover. Press the battery chamber release button. Install 8 AA batteries.
Recommended for use: Energizer® lithium batteries.
STEP 2
Insert SD Memory Card until you hear an audible click. Camera will not operate without SD Card.
Slide the power switch to ON. Press the Menu button to switch the camera to Setup, press Left button
to enter the OPTIONS and set time and date.
STEP 3
Eyelet
Mount camera in desired location using a mounting strap
or mounting bracket. NOTE: Camera must be attached to
a stable object for motion detection to function properly.
STEP 4
Switch camera to IR Aim. Aim camera using motion
detection to determine target area. Walk in front of the
camera at the desired distance and the camera LED will
flash showing the covered area. Switch camera to ON.
STEP 5
At Home
Remove the entire camera and transport to another location to download images. To connect the
camera to a PC computer, turn the camera ON, press the MENU button once to change to SETUP
Mode. Connect the USB cord (not included) between the USB out port and the PC computer. The
computer will recognize the camera as a removable drive. The unit works with Windows XP/Vista/7 or
Mac OS X 10.1 or higher. Copy the images and videos from the camera onto your PC for further
editing or printing. When the USB cable is disconnected, the camera will go back to SETUP mode.
See the full line of TRACE camera accessories at www.moultriefeeders.com
Page 10
B
PREMISE PRO Digital Surveillance Camera
Slide the power switch to ON. Close cover. The camera
will operate using Default settings. You may also
customize the settings if required.
C
Mounting
Strap
DEFAULT SETTINGS
DATE/TIME:
01/01/16 11:11pm
CAPTURE MODE:
3 PHOTO
START TIME:
ALWAYS ON
STOP TIME:
MIDNIGHT
CAMERA NAME:
TRACE CAM
ERASE ALL IMAGES:
NO
MANAGED MEMORY:
OVERWRITE OLDEST
PHOTO QUALITY:
LOW (4MP)
VIDEO QUALITY:
HD (1280x720)
VIDEO LENGTH:
30 SECONDS
SECURITY CODE:
00000
AC CONNECTED:
NO
WI-FI SD CARD:
NO
RESET TO FACTORY DEFAULTS:
NO
PREMISE PRO Digital Surveillance Camera
Page 3
D
CAPTURE MODES
The PREMISE PRO offers three capture modes as described below. The default capture mode is 3 PHOTO.
1 PHOTO
A single still photo is taken when movement is detected. Photos are stored in the DCIM/100MFCAM
folder on the SD card.
3 PHOTO
Three still photos are taken when movement is detected in a sequential manner with an approximate
1 second interval between images. Photos are stored in the DCIM/100MFCAM folder on the SD card.
F
CAMERA SPECIFICATIONS
Memory & Storage
Your camera supports external SD memory cards ONLY and will accept up to a 32GB card
(Class 4 or higher). Using large memory cards can slow the camera response. The camera
cannot capture any photo or video without external memory. Please insert an SD memory card
to operate camera. Estimates are based on the most common types of memory cards that can be
purchased at electronic stores, office supply stores, or online. Estimates may vary based on camera
settings or environmental conditions.
Important
VIDEO
Camera records a video when movement is detected by the motion sensor. The video length is
configurable in OPTIONS.
Always turn the unit off when inserting or removing an SD memory card to avoid damage and ensure
that the camera properly updates the memory information.
Photo Mode
E
SETUP AND PROGRAMMING
SD Card Size:
2 GB
16 GB
HIGH 4608 x 2592
1300
10400
LOW 2688 x 1512
3800
30400
Video Mode
PHOTODLY:00:29
B:99%9999/9999
When the camera’s power is turned ON, the display will come on to the Default Screen. Moving
clockwise from the top left, information is displayed for capture type, delay countdown for capture,
image count/remaining capacity, and battery level. If no buttons are pressed within 30 seconds, the
LCD screen will enter sleep mode to conserve battery life and enter capture mode based on current
settings. To wake the camera manually, press and hold the menu button until you see the default
screen on the display.
TRACE
PREMISE
<OPTIONS
START>
Setup Selection Setting
From the Default Screen, press the Menu button to enter the Main Screen. Press the Left button
to enter OPTIONS or Right button to START and force the camera to countdown and enter capture
mode. In the OPTIONS menu, Press the OK button, the selection will start to flash. Press the Up/Down
buttons to change the settings. Press the OK button again to Iock in selection. Press the Left button to
move to the next setting. Using this method you can customize your camera’s feature settings.
SD Card Size:
2 GB
16 GB
HD 1280 x 720 (based on 10 sec video)
110
880
VGA 640 x 480 (based on 10 sec video)
310
2480
Actual capacity will vary based on image properties.
Specifications
Operational Mode
Photo / Video
Resolution
12.0 MP
Still Resolutions
JPEG
Low 2688 x 1512
High 4608 x 2592
Video Resolutions
VGA- 640 x 480
HD 1280 x 720
SD Memory Card
Up to 32 GB SD card, Class 4 or higher (not included)
Format
JPEG - Still pictures, AVI - Video clips
Power Supply
8 AA Alkaline or Lithium batteries (not included)
From this Main Screen, press OK to get to the Test Capture screen.
Page 4
PREMISE PRO Digital Surveillance Camera
PREMISE PRO Digital Surveillance Camera
Page 9
AC
CONNECTED?
NO
AC Connected
When the camera is connected to an AC power supply and this option is selected, the camera will
remain on instead of going to a sleep state between detection and capture sequences. This will
greatly improve camera speed and performance and can be used in conjunction with most external
supplies, but is only recommended when connected to an AC power supply. In the event this option
is selected but no external supply is detected, it will default to the NO state. Press Left button to go
to the next option.
WI-FI
SD
SETUP AND PROGRAMMING (cont)
TEST
<NO
CAPTURE?
YES>
Test Capture
From the Main Screen, press the OK button to enter Test Capture mode. In this mode, you can force
the camera to take a test shot. This option is useful when placing your camera and making sure it is
aimed correctly. Press the Right button to take a test image. A 5-second countdown will commence
and the camera will take the test image.
CARD?
NO
Wi-Fi SD Card
Select option when using a Wi-Fi enabled SD card. Turning this feature on will keep the SD port
powered for a set amount of time to allow the files to transfer off the card to the Wi-fi network set up.
Press Left button to go to the next option.
Note: Moultrie does not offer technical support for Wi-Fi SD cards. Please contact your Wi-Fi card’s
manufacturer for support. Before use, you must setup your Wi-Fi SD card on your wireless network.
UPGRADE
E
FIRMWARE
S-770-130919
NO
Upgrade Firmware
The firmware version is displayed. Press Up/Down to choose setting.
YES - To upgrade firmware.
NO - Keep current firmware.
Make sure that an SD card with the new firmware is inserted into the camera. Press the OK button to
make selection. Make sure the process is completed before pressing other buttons or powering the
camera Off. Press Left button to go to the next option.
Setting OPTIONS
When you choose OPTIONS, the LCD Display will automatically display different feature within the
OPTIONS menu. Using the navigation process, set the features you desire.
DATE
&
TIME
01/01/16
11:11pm
Setting Date and Time
Press the OK button. Use the Left/Right buttons to move from one value to the next and the
Up/Down buttons to adjust each value. Press the OK button to lock in selections. When all your
selections have been made, and the date and time has been set, press the Right button to move to
the next option.
Setting Capture Mode
Press the OK button. Use the Up/Down buttons to choose between operating modes.
This camera has 3 modes.
A. 1 Photo - A single still photo is taken
when movement is detected.
CAPTURE
MODE
B. 3 Photo - Three still photos are taken
when movement is detected.
CAPTURE
MODE
CAPTURE
MODE
Note: This option will only be used if directed to do so by TRACE Customer Service.
RESET
TO
DEFAULTS?
FACTORY
NO
Reset to Default settings
You can reset your camera to the factory default settings. Press UP or DOWN to choose YES - all
setups restored to factory default or NO - keep custom settings. Press the OK button again to
make selection. Press Left button to return to the Main Screen.
Page 8
PREMISE PRO Digital Surveillance Camera
C. Video - Camera records a video when movement is
detected by the motion sensor. The video
length is configurable in OPTIONS.
PREMISE PRO Digital Surveillance Camera
1
3
PHOTO
PHOTO
VIDEO
Page 5
START
TIME
ALWAYS
ON
Start Time
Start time allows you to set specific operating times for the camera so that it will only look for activity
and capture images during times of interest. By default the START TIME is ALWAYS ON, meaning the
camera will look for and react to activity 24 hours per day. If desired, you may set the START TIME to
a specific hour upon which the camera will wake up and begin capturing images when movement is
detected, turning off at the defined STOP TIME. To change the START TIME, press the UP/DOWN buttons
to highlight the desired time and then press OK. Press Left button to go to the next option.
STOP
TIME
MIDNIGHT
Stop Time
Like START TIME, STOP TIME allows you to control when the camera will react to movement and
capture images. If a START TIME is defined, Setting the STOP TIME will determine when the camera
will cease capturing images when movement is detected. To change the STOP TIME, press the
UP/DOWN buttons to highlight the desired time and then press OK. Press Left button to go to the
next option.
NOTE: If Start Time is set to ALWAYS ON, Stop Time will be hidden.
CAMERA
NAME
ALL
IMAGES
NO
Erase Images
Press the OK button. Use the Up/Down buttons to choose between Yes - erase all images, or
No - does not change stored images. Press the OK button to select. When your selection has been
made, press Left button to go to the next option.
NOTE: This will also format your SD card for use in your camera.
Page 6
MEMORY
OVERWRITE
OLDEST
Managed Memory
Selecting the OVERWRITE OLDEST option will cause the oldest files to be overwritten with new
captures when the SD card reaches its capacity. With the DO NOT OVERWRITE option selected, the
camera will cease image capture once the SD card reaches capacity. Press the OK button to select.
When your selection has been made, press Left button to go to the next option.
PHOTO
QUALITY
LOW(4MP)
Setting Photo Quality
Press the OK button. Use the Up/Down buttons to choose between 4 image resolution settings.
1. High (12MP):
4608 x 2592
2. Low (4 MP):
2688 x 1512
Press the OK button to confirm the selection. Press the Right button to move to the next option.
VIDEO
QUALITY
HD
(1280X720)
Setting Video Quality
Press the OK button. Use the Up/Down buttons to choose between 2 image quality settings.
1. HD:
1280 x 720
2. Low:
640 x 480
Press the OK button. Press Left button to go to the next option.
TRACE CAM
Setting Camera Name
Press the OK button. Use the Up/Down and Left/Right buttons to select an identity for your
camera. For example, you can use a name or a location; the identity you wish to use is up to you.
Press the OK button. Press Left button to go to the next option.
ERASE
MANAGED
PREMISE PRO Digital Surveillance Camera
VIDEO
LENGTH
30
SECONDS
Video Length
Press the OK button. Use the Up/Down buttons to choose between 2 video length settings
(10 or 30 seconds). Press the OK button. Press Left button to go to the next option.
PROGRAM
SECURITY
CODE00000
Security Code
Press the OK button. Use the Up/Down and Left/Right buttons to select a 5 digit security code
for your camera. Press the OK button. Press Left button to go to the next option.
NOTE: Please remember your security code. If the code is lost, you can contact TRACE
customer support to reset the password. (Charges may apply)
PREMISE PRO Digital Surveillance Camera
Page 7