H10X/H5X
H5E/DV PC
With Digital Control Board
Supercedes:
10420.0001; 10889.0001; 39338.0000
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit
the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain
the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain
a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.
39338.0001A
07/09 © 2009 BUNN-O-MATIC CORPORATION
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone
at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior
authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN
are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
BrewWISE, BrewLOGIC, BrewMETER, BrewWIZARD, Bunn Gourmet, BUNN Gourmet Ice, BUNN Pour-O-Matic, BUNN,
Bunn-OMatic, Bunn-O-Matic, BUNNlink, BUNNserve, BUNNSERVE, BUNN Espress, Cool Froth, DBC, Dr. Brew, Dual, EasyClear, EasyGard, Easy Pour, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, IMIX, Infusion Series, Intellisteam,
Quality Beverage Equipment Worldwide, The Mark of Quality in Beverage Equipment Worldwide, My Café, PowerLogic,
Safety-Fresh, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, System
III, ThermoFresh, 392, AutoPOD, AXIOM, Beverage Profit Calculator, Beverage Bar Creator, BUNNsource, Coffee At Its
Best, Digital Brewer Control, Nothing Brews Like a BUNN, Pouring Profits, Pulse Wave, Signature Series, Smart Heat,
Tea At Its Best, The Horizontal Red Line, Titan, Ultra, are either trademarks or registered trademarks of Bunn-O-Matic
Corporation.
2
39338.1 012609
CONTENTS
Warranty........................................................2
Introduction...................................................3
User Notices..................................................3
Electrical Requirements.................................4
Plumbing Requirements................................5
Initial Set-Up..................................................5
Programming.................................................6
Draining the Dispenser...................................8
Cleaning.........................................................8
INTRODUCTION
This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel
above the faucet that indicates the status of the dispenser. This equipment is for indoor use, either wall-mounted
(H5E/H5X/H5-PC only) or on a sturdy counter or shelf.
USER NOTICES
The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels.
This equipment must be installed to comply
with the International Plumbing Code of the
International Code Council and the Food
Code Manual of the Food and Drug Administration (FDA). For models installed outside
the U.S.A., comply with the applicable
Plumbing /Sanitation Code.
00656.0000
! WARNING
Fill water tank before turning - on thermostat or connecting appliance
to power source.
Use only on a properly protected
circuit capable of the rated load.
Electrically ground the chassis.
Follow national/local electrical codes.
Do not use near combustibles.
120V
120/208-240V
00831.0000
FAILURE TO COMPLY RISKS EQUIPMENT
DAMAGE, FIRE, OR SHOCK HAZARD
READ THE ENTIRE OPERATING MANUAL
BEFORE BUYING OR USING THIS PRODUCT
THIS APPLIANCE IS HEATED WHENEVER
CONNECTED TO A POWER SOURCE
00831.0000F 3/98 ©1998 BUNN-O-MATIC CORPORATION
00831.0000
To reduce the risk of electric shock,
do not remove or open cover.
No user-serviceable parts inside.
Authorized service personnel only.
Disconnect power before servicing.
NOTICE
37881.0000
120 V, 15.4 A, 1850 W
1PH, 2-Wire + GND, 60HZ
29710.0000
ALL COMPONENTS ARE
200 TO 240 VOLT A.C.
Replace only with
components listed in the
accompaning literature
rated for the same
voltage
! WARNING
Hot Water
Use With Care
Optional Field Wiring
12537.0000
12593.0000
Optional Field Wiring
120/208-240 V, 16.9 A, 4050 W
1PH, 3-Wire + GND, 60HZ
29710.0000
3
39338.1.1 072409
ELECTRICAL REQUIREMENTS
WARNING - The dispenser must be disconnected from the power source until specified in Initial Set-Up.
Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
WHITE
NEUTRAL
L1 BLACK
NEUTRAL WHITE
N
L1 BLACK
POWER CORD
L2 RED
L1
L1 BROWN
GREEN
120 volt ac models
Note: This electrical service consists
of 2 current carrying conductors (L1
and Neutral) and a separate conductor
for earth ground.
L2 RED
L1
L2
L1 BLACK
L1
GREEN
G
POWER CORD
L2 RED
L1 BLACK
GREEN/YELLOW
G
POWER CORD
NEUTRAL BLUE
N
L1 BLACK
G
208 & 240 volt ac models
230 volt ac models
Note: This electrical service consists
of 2 current carrying conductors (L1
and Neutral) and a separate conductor
for earth ground.
Electrical Hook-Up
CAUTION – Improper electrical installation will damage electronic
components.
1.An electrician must provide electrical service as specified.
2.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.
3.Turn off master switch (if equipped).
4.Remove the upper and lower rear panels (side panel on H10X).
5.Install the proper electrical wiring to the terminal block.
6.On Dual Volt models, make sure the toggle switch below the circuit
board is set to the desired voltage (120 volts or 208/240 volts) and
the red switch on the circuit board is in the “SET” position.
7.Connect the dispenser to the power source and verify the voltage at
the terminal block before proceeding. Reinstall both rear panels.
8.If plumbing is to be hooked-up later be sure the dispenser is disconnected from the power source. If Plumbing has been hooked-up, the
dispenser is ready for Initial Set-Up.
Note: This electrical service consists
of 2 current carrying conductors (L1
and L2) and a separate conductor for
earth ground.
POWER CORD
L2 RED
L2 RED
WHITE
NEUTRAL WHITE
N
NEUTRAL
L1 BLACK
L1 BLACK
L2
L1
GREEN
G
120/208 & 120/240V ac
single phase models
Note: This electrical service consists
of 3 current carrying conductors
(Neutral, L1 and L2) and a separate
conductor for earth ground.
DUAL VOLT TOGGLE SWITCH
CE REQUIREMENTS
• This appliance must be installed in locations where it can be overseen by
trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance
with all local and national codes.
• This appliance must not be cleaned by water jet.
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of this appliance by a person
responsible for its safety.
• Children should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with
a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.
4
39338.1 072409
PLUMBING REQUIREMENTS
This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi
(138 and 620 kPa)from a ⁄2” or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345
kPa). The water inlet fitting is ⁄4” flare.
1
1
NOTE - Bunn-O-Matic recommends ⁄4” tubing for installations of less than 25 feet and ⁄8” for more than 25 feet
from the ⁄2” water supply line. At least 18 inches of an FDA approved flexible beverage tubing, such as reinforced
braided polyethylene or silicone, before the dispenser will facilitate movement to clean the countertop. BunnO-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole
made in the supply line by this type of device may restrict water flow.
1
3
1
This equipment must be installed to comply with the International Plumbing Code of the International
Code Council and the Food Code Manual of the Food and Drug Administration (FDA). For models installed
outside the U.S.A., you must comply with the applicable Plumbing/Sanitation Code for your area.
Plumbing Hook-Up
1. Remove the shipping cap from the fitting on the rear of the dispenser, and attach the flare elbow fitting
(supplied separately with the dispenser) to the fitting. (H10X has flare fitting w/o adaptor)
2. Flush the water line and securely attach it to the flare fitting.
H5E/X/DV-PC
H10X
INITIAL SET-UP
CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except
when specified in the instructions.
1. Connect dispenser to the power source and turn on water supply.
2. Place master ON/OFF switch in the ON position (if equipped).
3. Water will automatically flow into the tank to the proper level and shut-off. When filled, the water heater will
turn on automatically.
4. The tank will heat to the (set) temperature.
5. Refer to Programming to set the Tank Temperature and the Ready Temperature.
5
39338.1 072409
PROGRAMMING
When power is applied to the dispenser, the display located on the bottom of the main circuit board will show
the software version for 5 seconds, and then it will show the model number (see chart below) it will then go
to (-). While the tank is filling, the display will read (FIL). When the tank is full the display will show the model
number and then go to (-).
MODEL DISPLAYS
(H5H)
(H5L)
(HPC)
(H10)
5 Gallon High Voltage Unit (200-240V)
5 Gallon Low Voltage Unit (100-120V)
5 Gallon Portion Control Unit (all)
10X (all)
Switch must be in “SET” position for
access into programming modes.
LEFT
BUTTON
CENTER
BUTTON
RIGHT
BUTTON
LEVEL 1 PROGRAMMING
1. Before programming any settings into the Control Board, confirm the correct model
number is entered.
2. Do this by pressing and holding down on the center button until P1 appears on the
display. Release the center button. The display will now show the model number
(ex: H5H). Now scroll with the (+/-) buttons through the models listed above until
the display matches the model you are working with.
3. Press and release the center button once more. The display will show P2. Display
will now show the tank temperature (ex: 200). Press the (+) button to increase the
temperature set point, or the (-) button to decrease the set point.
NOTE: If the unit is a H5X or H10X, set the Tank Temperature to 212°F.
4. After the Tank Temperature is entered, press and release the center button once
more. The display will read P3, then show the ready temperature set point. Factory
default is 195° F for most dispensers, and 85° F for some.
5. Press the (+) button to increase the set point, or the (-) button to decrease the set
point.
6. To exit Level 1 Program press and release the center button once more. The display
will show Software version, then model number, then (-).
6
39338.1 072409
PROGRAMMING (Continued)
LEVEL 2 PROGRAMMING
H1 - DISPENSE TEMPERATURE LOCKOUT - PORTION CONTROL ONLY
(WILL NOT DISPLAY ON OTHER MODELS)
1. To enter Level 2 Programming, press and hold the center button until H1 appears on the display (approximately 6 seconds) then release button. The display
will either read noL (LOCKOUT DISABLED) or Loc (LOCKOUT ENABLED). When
(ENABLED), unit will not dispense if the Tank Temperature is below the (READY)
temperature setting.
2. Use the (+) or (-) buttons to alternate between Loc and noL.
3. Press and release the center button once more to advance to H2.
H2 - F° OR C° SELECTION
1. To enter Level 2 Programming, press and hold the center button until H2 appears
on the display (approximately 6 seconds). Release the center button, The display
will show either FAH (Degrees in Fahrenheit) or CEn (Degrees in Centigrade).
2. Press and release the (+) or (-) buttons to alternate between FAH and CEn.
3. After setting FAH or CEn, to exit Level 2 Programming, press and release the
center button twice. Software version, then model number, then (-).
H3 - RESTORING FACTORY DEFAULTS
1. To restore Factory Defaults (This clears all settings that were previously entered),
press and release the center button until H2 appears on the display (approximately
6 seconds). Release the Center Button, then press and release the Center Button
once more. The display will read H3, then show (- - -).
2. Press and hold both (+) and (-) buttons to initiate the resetting of the factory
default settings. The display (- - -) will flash on and off during this time (about 5
to 7 seconds).
3. When the factory default numbers are loaded in, the display will stop flashing,
then read don (DONE). You can now release the two buttons.
NOTE: If you release the two buttons at any time before the display reads don, the Factory
Default numbers will not be entered. The old numbers will remain in the memory.
4. To exit Level 2 Programming press and release the center button once more. The display will show the Software version, then model number, then (-).
7
39338.1 072409
OPERATING CONTROLS - PORTION CONTROL ONLY
d.
(a) VOLUME SELECTOR BUTTONS
Press and release the button corresponding to the Small, Medium, or
Large volume, to select the desired
amount of water to be dispensed.
Pressing a different button after a
cycle has been initiated does not
change the volume in progress.
(b)AUTO STOP/MANUAL DISPENSE
BUTTON
Press and release button to stop a
dispense cycle. Press and hold button
to dispense manually.
(c) HIDDEN PROGRAMMING BUTTON
(d)LED INDICATORS
(e)DISPENSE NOZZLE
c.
a.
b.
e.
ADJUSTING DISPENSE VOLUMES
NOTE: The dispenser should be at operating temperature before setting dispense volumes.
1. Press and hold the hidden programming button (c) located under the ® next to the BUNN logo on the front
of the dispenser until the 3 LED's begin flashing from the left to the right. Release the button.
2. Place an empty graduated container under the dispense nozzle (e).
3. Press and release the batch size to be set (a). The LED's will stop flashing, and the LED over the button just
pressed will come on steady. Water will begin to dispense into the container.
4. When the desired amount of water is dispensed, press and release the same button (a). The water will stop
dispensing and the batch size is now set.
5. The LED's will begin flashing from left to right again. Repeat steps 2 thru 4 to set up the other batch sizes.
6. To exit the programming set up at any time, press and release the hidden button once (c). The dispenser is
now ready for use.
8
39338.1 072409
DRAINING THE DISPENSER
CAUTION - The dispenser must be disconnected from the power source throughout these steps.
1.
2.
3.
4.
5.
Disconnect the dispenser from the power source.
Shut-off and disconnect the incoming water supply and allow dispenser to cool.
Remove the 4-40 screws and the top cover.
Gently remove one of the grommets from the tank lid.
Insert a tube to the bottom of the tank and syphon ALL of the water out.
NOTE - The dispenser must be full using the INITIAL SET-UP steps before reconnecting to the power source.
CLEANING
The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment.
H5E/H5E-PC/H5X ONLY:
WALL MOUNTED INSTALLATION
If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or
table top. Use B.O.M. part #12542.0000 for side mounted Wall Bracket Kit or # 13125.0001 for front mounted
Wall Bracket Kit .
SUPPORT FOR LARGE RECEPTACLES
CAUTION: If the dispenser is to be used with larger receptacles such as pitchers or pots, those receptacles must
be adequately supported during dispensing of hot water to avoid spillage of very hot water. This support may be
provided by a table or counter top, or use B.O.M. part #12599.0000 Shelf Kit.
9
39338.1 072409
Download PDF