Instructions – Parts List
10:1 PRESIDENT PUMP
Hydra-Cleanr Units
306817K
For Mounting on Open 55 Gallon Supply Drum
(Can be wall-mounted with accessory bracket)
Model 206515, Series C
7 MPa, (69 bar, 1000 psi) Maximum Working Pressure
0.7 MPa, (7 bar, 100 psi) Maximum Incoming Air Pressure
D Stainless steel pump and spray valve handle powerful clean
solutions at high pressure.
D Divorced design pump – keeps cleaning solution from fouling air
motor.
D Accumulator reduces line pulses – air charged at the factory.
D Air line lubricator for automatic lubrication of air motor.
D Suction tube has intake filter.
Solution volume and working pressure can be adjusted using a
different tip orifice size and an air regulator. Fan pattern can be
changed to concentrating jet stream using blasting tip.
Read warnings and instructions.
See page 2 for Table of Contents.
06017B
GRACO INC.P.O. BOX 1441MINNEAPOLIS, MN55440-1441
Copyright 1996, Graco Inc. is registered to I.S. EN ISO 9001
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . .
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
14
14
16
16
Symbols
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
Use this pump only for pumping water and water–diluted cleaning solutions in a pressure washing system. Never use the pump for paint or any other coatings. Any misapplication of the pump may cause
dangerous operating conditions which can result in serious injury and substantial property damage.
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
D Do not alter or modify this equipment. Use only Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Handle hoses carefully. Do not pull on hoses to move equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 66_C (150_F) or below –40_C (–40_F).
D Wear hearing protection when operating this equipment.
D Do not move or lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
2
306817
WARNING
INJECTION HAZARD
Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an
extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin
can also cause a serious injury.
D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medical attention.
D Do not point the spray gun at anyone or at any part of the body.
D Do not put hand or fingers over the spray tip.
D Do not stop or deflect fluid leaks with your hand, body, glove, or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the spray gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 6 whenever you: are instructed to relieve pressure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.
D Tighten all the fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Do not repair high pressure couplings; replace the entire hose.
D Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the pump.
D Never operate the pump with the air motor plates removed.
D Before checking or servicing the equipment, follow the Pressure Relief Procedure on page 6 to
prevent the equipment from starting unexpectedly.
306817
3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Before operating this equipment, electrically disconnect all equipment in the spray area.
D Before operating this equipment, extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or off any light switch in the spray area while spraying or while operating if fumes
are present.
D Do not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
4
306817
Setup
Grounding
7. Object being sprayed: follow your local code.
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE OR EXPLOSION
HAZARD on page 4.
Although water generally provides a natural electrical
ground, the following equipment must be grounded if
the cleaning chemical are volatile.
1. When cleaning in enclosed areas, such as storage
tanks, locate the pump and air compressor outside
the area and well away from it. Provide adequate
ventilation. If the area you are cleaning has stored
flammable materials. take appropriate precautions
to avoid static sparking. Consul your local codes.
8. Solvent pails used when flushing: follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding continuity.
9. To maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the spray
gun firmly to the side of a grounded metal pail,
then trigger the gun.
General Information
The typical setup shown in Figure 2 is only a guide to
selecting and installing required and optional components. For assistance in designing a system to suit
your needs, contact your Graco distributor. Refer to
Figure 2 for callouts in parentheses.
Connect Hoses and Mount Pump
2. Pump: use a ground wire and clamp. See Fig. 1.
Loosen the grounding lug locknut (W) and washer
(X). Insert one end of a 1.5 mm@ (12 ga) minimum
ground wire (Y) into the slot in lug (Z) and tighten
the locknut securely. Connect the other end of the
wire to a true earth ground. Order Part No. 237569
Ground Wire and Clamp.
2. Using LoctiteR Pipe Sealant, screw the accumulator (7) inlet adapter into the pump outlet. Connect
the fluid hose to the accumulator, the nozzle to the
spray valve, and the air line lubricator (3) to the
pump air inlet. Hang the pump on your cleaning
solution drum.
W
Y
X
NOTE: The filter on the suction hose should be about
1/2 in. (12.7 mm) off the bottom of the drum. If the
hose is too long, cut it off as necessary.
Z
0864
Fig. 1
3. Air and fluid hoses: use only electrically conductive
hoses.
4. Air compressor: follow manufacturer’s recommendations.
5. Spray gun: ground through connection to a properly grounded fluid hose and pump.
6. Fluid supply container: follow your local code.
1. Using Loctite Pipe Sealant, screw the hose
stud (10) of the suction hose into the pump’s
intake housing. See Fig. 2. Remove one of the
screws from the pump base opposite the outlet,
and assemble the hanging bracket (19) to the
pump with the provided screw (9) – use the lockwasher that was on the replaced screw.
3. Close the air ball valve (24), then connect your 1/2
ID (min) air supply hose to the 1/2 nptm(f) inlet
union (15) – do not use thread sealer. Install an
accessory air filter and water separator to remove
excessive moisture that could cause air motor
icing. Pour high quality SAE 10 into the lubricator
until oil reaches the level mark on the sight glass.
CAUTION
Oils containing phosphate ester or chlorinated hydrocarbons are not compatible with the plastic bowl of
the lubricator – be sure that oil used to lubricate the
compressor is free of these additives.
306817
5
Operation
Pressure Relief Procedure
WARNING
INJECTION HAZARD
Fluid under high pressure can be injected through the skin and cause
serious injury. To reduce the risk of an
injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
D
D
D
D
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray nozzles.
1. Lock the Hydra-CleanR gun trigger safety.
2. Close the pump air regulator.
6
306817
3. Close the red handled bleed-type master air valve
(required in your system)
4. Unlock the gun trigger safety and trigger the gun to
relieve pressure.
5. Lock the gun trigger safety.
6. Open the pump drain valve, having a container
ready to catch the drainage.
7. Leave the drain valve open until you are ready to
spray again.
If you suspect that the dispensing valve, extension, or
grease fitting coupler is clogged, or that pressure has
not been fully relieved after following the steps above,
VERY SLOWLY loosen the coupler or hose end coupling and relieve pressure gradually, then loosen
completely, now clear the clog.
Operation
WARNING
24
To avoid serious injury, including fluid injection and
splashing in the eyes or on the skin, never point the
gun at yourself or anyone else.
3
7
Before Using
Prepare cleaning solution as instructed, observing all
safety precautions. Pre-mix powered cleaners in a
separate bucket of hot water before adding to water in
the supply drum.
*1
34
9
19
10
WARNING
06018B
Take care not to get spray containing cleaning
chemicals into your eyes, ears, or nose. If any
spray does get on your skin or in your eyes, flush
immediately and thoroughly with water. Seek
immediate medical attention.
See Fig. 2. Open the main air supply valve, hold the
spray valve open and slowly open the air petcock until
the pump is running slowly. After solution is coming
from the spray nozzle, open the ball valve (24) all the
way and adjust the air line lubricator (3) to deliver
about 1 drop per minute. Refer to the separate lubricator instruction manual.
Release the spray valve trigger and let the pump run.
The pump will charge the accumulator with liquid
pressure, then stall.
NOTE: Protect surfaces that might be damaged by the
cleaning solution and rinse before the solution dries on
both surfaces. You can clean stubborn dirt off better
with a stronger, heated solution.
Useful Hints
15
16
Fig. 2
After all the dirt is cleaned off, rinse all the solution off
with clear, cold water. When you are through cleaning,
close the air petcock and relieve the pressure.
Shutdown and Care of Unit
CAUTION
Do not allow the pump to run dry. It will quickly
accelerate to a high speed, causing damage. If your
pump is running too fast, stop it immediately and
check the fluid supply. If the container is empty and
air has been pumped into the lines, refill the container and prime the pump and the lines, or flush and
leave it filled with a compatible solvent. Eliminate all
air from the fluid system.
WARNING
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 6.
Hold the spray nozzle about 2 feet (0.6 m) from the
surface and completely mist-wet the object you are
cleaning. Let it soak briefly, then use the spray to
“chisel” the dirt off – keep the nozzle about 6 in.
(152.4 mm) from, and at an angle to the surface. If
some dirt remains, wet the surface again. Let the
object soak a little longer, then hold the nozzle as
close as possible and spray to blast the dirt off.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 6.
When shutting down for the day or weekend, shut off
the main air supply and relieve the pressure. Rinse
all solution off the equipment with clear, cold water,
Shut off the water supply valve and relieve the water
pressure.
Check the air line lubricator (3) often and keep it filled
with oil. Also check the pump packing nut regularly and
keep it just tight enough to stop leakage, but no tighter.
Use a 1/4 in. diameter rod to tighten.
306817
7
Troubleshooting
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 6.
Before servicing this equipment always make sure to
Relieve the pressure.
Note: Check all possible problems and solutions
before disassembling.
Problem
Cause
Solution
Excessive surge
g at spray
y nozzle
Obstructed spray tip, valve, or hose
Clean, clear
Cleaning solution supply empty
Refill
Accumulator not working
Recharge – see page 9 and manual
306933
Clogged intake filter, kinked or collapsed suction hose
Clean, unkink
Fluid leaking from valve
Loose packing nut or worn packings
See manual 307010
Valve will not stop dispensing
g
Valve not adjusted properly
See manual 307010
Dirty or worn valve stem or seat
Clean, clear, or replace – See manual
307010
Cleaning solution supply empty
Refill
Clogged intake filter, kinked or collapsed suction hose
Clean, unkink
Dirty or worn valve stem or seat
Clean clear, or replace – See manual
307010
Dirty or worn fluid piston or packings
Service – See manual 308117
Pump operating, but spray pressure low on up stroke.
Dirty or worn fluid piston or packings
Service – See manual 308117
Pump operating, but spray pressure low on down stroke
Dirty or worn fluid intake valve
Clean, clear, or replace – See manual
308117
Pump operating, but spray pressure low on both strokes
Clogged intake filter, kinked or collapsed suction hose
Clean, unkink
Dirty or worn fluid piston or packings
Service – See manual 308117
Dirty or worn fluid intake valve
Clean, clear, or replace – See manual
308117
Loose packing nut or worn packings
Tighten, replace – See manual
308117
Restricted air line
Check for closed valve; use larger
supply hose
Pump throat packing nut too tight
Loosen
Pump air motor not working
Service – See manual 306982
Restricted air line
Check for closed valve; use larger
supply hose
Pump air motor not working
Service – See manual 306982
Valve will not stop the pump
Fluid will not come from pump
((hose removed))
System will not spray
8
306817
Service
General
See Fig. 2. Check the air line lubricator often and keep
it filled with oil. Also check the pump packing nut
regularly to keep it just tight enough to stop leakage,
but no tighter. Use a 1/4 in. (6.3 mm) diameter rod to
tighten.
Proper packing nut take-up will stop leakage. However,
all the packings should be replaced after 1000 hours
of operation or delivery of 120,000 gallons of solution
at 2 gpm. Use Repair Kit 206923.
Accumulator Repair
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 6.
NOTE: Before disassembling the accumulator (7),
check the air valve for leakage. Remove the air valve
cap and recharge the air chamber to 0.58–1.36 MPa
(5.78–13.6 bar, 85–200 psi). Wet the valve stem with
saliva and watch for bubbling, indicating leakage. If
leakage it detected, replace the valve core – release
the air pressure first by depressing the valve core
plunger pin.
1. Shut off the air supply to the pump and relieve the
pressure. Release air pressure in the accumulator
by depressing the valve core plunger pin. Disconnect the spray hose and remove the accumulator
from the pump.
2. Screw the inlet adapter out of the housing and
remove the o-ring, poppet, and spring. Screw the
housing off of the cylinder. Take the piston out and
remove the bearings and seal. Clean all parts and
inspect for wear and damage, replacing as necessary. Check the piston and cylinder wall for pitting
or scoring. Check the valve seat in the inlet adapter for wear or damage.
3. Lubricate the piston seal, and reassemble the
accumulator. Remount the accumulator on the
pump and reconnect the spray hose. Charge the
accumulator to 0.58–1.36 MPa (5.78–13.6 bar,
85–200 psi). Start the pump and check for air or
liquid leaks.
306817
9
Accessories
Stainless Steel Spray Tips
AIR SUPPLY TO PUMP
TIP
NO.
ORIFICE
SIZE
SPRAY
ANGLE
164435
.043
40
160964
.043
25
164434
.052
25
164436
.052
40
160957
.062
40
160963
.062
25
KEY:
GPM : Gallons Per Minute
CFM : Cubic Feet Per Minute
PSI : Pounds Per Square Inch
WP : Working Pressure in PSI
Stainless Steel Blasting Tips
10
TIP NO.
ORIFICE SIZE
102442
.067
102446
.086
102450
.125
306817
476 kPa
(4.76 bar, 70 PSI)
680 kPa
(6.8 bar, 100 psi)
GPM
CFM
WP
GPM
CFM
WP
12
1.2
13
630
14
1.4
19
885
16
1.6
17
610
18
1.8
24
840
23
2.3
23
560
26
2.6
32
750
Notes
306817
11
Parts
Model 206515 President Hydra-Clean
32
5
31
37
23
24
7
3
15
11
38
*1
34
10
9
8
6
19
22
16
18
Ref. No. 6
4*
22c
22b
22d
12
306817
06016B
22a
Parts
Model 206515
President Hydra-Clean
Includes items 1–38
Ref
No.
Part No.
Description
1*
205753
3
4*
5
214847
206300
224346
6
237485
7
207278
8
9
10
11
102123
102235
102550
158256
15
162505
16
18
162802
164085
SPRAY HOSE; cpld 3/8 npt(m);
3/8 ID; 40’ (12.2 m)
AIR LINE LUBRICATOR
SUCTION HOSE FILTER
10:1 PRESIDENT PUMP
See manual 308117 for parts
SPRAY GUN
See manual 307010 for parts
AIR CHARGED ACCUMULATOR
(See manual 306933 for parts)
CLAMP, hose
CAPSCREW, hex hd; 1/4–20 x 1/2”
STUD, barbed hose; 3/8 npt(m)
UNION, swivel; 1/2 nptf
x 3/8 npsm
UNION, str swivel; 3/8 npt(m)
x 1.2 npt(f) swivel
HOSE, plastic; 3/4” ID; 24” (.6 m) long
SPRING, reinforcing
Qty.
1
1
1
Ref
No.
Part No.
Description
19
22
165280
207299
22a
164017
22b
103921
22c
22d
23
24
175019
220220
108066
113333
31
32
34
37
38
113498
237569
102024
100176
235208
BRACKET, pump mounting
SPRAY NOZZLE EXTENSION KIT
Includes items 22a –22d
. TUBE, straight threaded; 1/4 npt(m);
10” (254 mm) long
. TIP, spray; .062 orifice;
40 fan_ angle
. ADAPTER; 1/4 npt(f) x 11/16 ns(m)
. GUARD, tip
TEE; 1.4 npt(f)
BLEED-TYPE AIR VALVE,
red handled
VALVE, air relief
GROUND WIRE
WASHER, lock
BUSHING, hex
UNION, swivel
1
1
1
2
1
1
1
1
1
1
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
* Recommended Tool Box spare parts. Keep these
spare parts on hand to reduce down time.
306817
13
Dimensions
1/2 npt air inlet
14–3/4”
(375 mm)
28–3/16”
(715 mm)
06019
Technical Data
Air pressure range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 to 850 kPa (1.5 to 8.5 bar, 20 to 120 psi)
Air volume requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 cfm (0.64 m3/min) at 480 kPa (4.8 bar, 70 psi),
(With .062 in spray tip, included)
32 cfm (0.90 m3/min) at 690 kPa (6.9 bar, 100 psi)
Pump ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10:1
Max. recommended pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 cycles per min. or 3 gpm
Pump discharge pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 MPa (83 bar, 1200 psi)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 lb (24.95 kg)
Sound pressure level* at 100 psi (6.8 bar, 0.68 MPa)–40 cycles/min (at one meter). . . . . . . . . . . . . . . . . . . . . . 83 dBa
Sound power level* at 100 psi (6.8 bar, 0.68 MPa)–40 cycles/min. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 dBa
* Sound power level was tested in accordance with ISO 9614–2.
14
306817
Notes
306817
15
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the
exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of
sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment
is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers
to identify the distributor closest to you:
1–800–367–4023
612–623–6921
612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit
International Offices: Belgium, Korea, Hong Kong, Japan
GRACO INC.
P.O. BOX 1441
MINNEAPOLIS, MN
www.graco.com
PRINTED IN U.S.A. 306817 08/1983, Revised 02/2002
16
306817
55440–1441