en Instructions for use 9000 005 762 (8402)

 en
Index
Safety instructions . . . . . . . . . . . . .
Getting to know your appliance . .
Before using your appliance
for the first time . . . . . . . . . . . . . . . .
Filling in the Salt . . . . . . . . . . . . . . .
Setting up the water softener . . . .
Filling with rinse aid . . . . . . . . . . . .
Unsuitable dishes . . . . . . . . . . . . .
Arranging crockery, glasses,
etc. in the dishwasher . . . . . . . . . .
Detergents . . . . . . . . . . . . . . . . . . .
4
6
7
8
9
10
11
12
15
Opening and closing the door . . .
serve@Home * . . . . . . . . . . . . . . . .
Adjusting the appliance . . . . . . . . .
auto 3in1 . . . . . . . . . . . . . . . . . . . . .
Programme overview . . . . . . . . . .
Selecting options/standard settings
Maintenance and care . . . . . . . . . .
Fault finding . . . . . . . . . . . . . . . . . .
Customer Service . . . . . . . . . . . . .
Notes . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . .
17
18
19
19
21
22
28
30
33
33
34
en
Safety instructions
Delivery
Immediately check the packaging and
dishwasher for any damage which may
have been caused in transit. Do not use
a damaged appliance, but consult your
supplier.
Please dispose of packaging material
properly.
The corrugated cardboard consists
mainly of waste paper.
The polystyrene moulded parts have
been foamed without any CFCs.
The polyethylene film (PE) consists
partly of secondary raw material.
The wooden frames (if fitted) are made
of residual wood and are untreated.
The hoops (if fitted) consist of
polypropylene (PP).
4
Installation
Install and connect the appliance
according to the installation and
assembly instructions.
The dishwasher must NOT be
connected to the power supply during
installation.
Ensure that the protective conductor
system of the domestic electricity
supply has been installed correctly.
Electrical connection conditions must
correspond with the specifications on
the rating plate of the dishwasher.
In order for your dishwasher to become
serve@Home capable, you will need
a special accessory, the System
Interface (available from your specialist
supplier). Please follow the enclosed
installation instructions, and install the
system interface in the chamber located
at the front of the dishwasher.
Built-under and built-in appliances
should always be installed under a
continuous work surface which is
attached to the adjacent cupboards, in
order to ensure that the appliance is
entirely stable.
After the appliance has been installed,
the mains plug should still be easily
accessible.
Not on all models:
The plastic housing on the water input
contains an electrically operated valve.
The connecting wires are inside the
inlet hose. Do not cut through this hose
and do not immerse the plastic housing
in water.
en
Warning
For safety reasons, if the appliance is not
fitted in a recess, thereby making a side
wall accessible, the door hinge area
should be covered at the side.
(Risk of injury)
Covers are available as optional
accessories from customer services or
specialist stores.
In daily use
Warning
Knives and other utensils with sharp points
must be placed in the baskets either flat or
with the points downwards.
Use the dishwasher only in the
household and only for its designed
purpose, i.e. for washing domestic
dishes.
Do not lean or sit on the open door.
The appliance could tip.
The water in the appliance is not
drinking water.
Do not add any solvents to the washing
chamber. Danger of explosion!
Open the door carefully when the
programme is still running. Water could
spray out of the appliance.
Read and observe the safety
information and instructions for use on
the packaging for cleaning and rinsing
agents.
Children in the household
Do not let infants play or operate the
dishwasher.
Keep cleaning and rinsing agents out of
the reach of infants.
Keep infants away from the open
dishwasher. It could contain residue of
the cleaning agent.
To prevent injuries, e.g. caused by
stumbling, open the dishwasher only
briefly in order to load and unload the
dishwasher.
If a fault occurs
Repairs or other work on the
dishwasher should only be carried out
by a qualified specialist.
The dishwasher must be disconnected
from the electricity supply before any
repairs or other work are started. Pull
the mains plug out of the wall socket or
switch off at the fuse box. Grasp the
plug to remove it from the socket; do
not tug on the cable. Turn the water off
at the tap.
When disposing of old
appliances
Appliances that have reached the end
of their service life should be rendered
inoperable in order to exclude the
possibility of subsequent accidents. Pull
the mains plug out of the wall socket,
cut through the connecting cable and
disable the door lock.
Take the appliance to a designated
waste disposal centre.
Warning
Children could get locked in the appliance
(risk of suffocation) or get stuck in other
positions.
Therefore: Remove the mains plug, cut the
mains wire and set aside. Damage the
door lock so that the door can no longer
be closed.
5
en
Getting to know your
appliance
Diagrams of the control panel and the
interior of the appliance can be found
in the envelope at the front.
Individual positions are referred to in
the text.
Control panel
1
2
3
4
5
6
Main switch
Button M/OK: Select options, store
(changed) value
Buttons – and +: Select programmes
and settings
This display gives optical character
information on the programmes,
options, and settings to be selected
as well as on the available actions.
Start Button: Start programme
Door Opener
The luminous arrows indicate whether you
are able to select among other options
using – or + 3 .
This dishwasher is equipped with touch
buttons. A gentle touch starts the function.
Always keep the user interface clean
and free of grease in order to prevent
malfunctions. Use a dry or lightly
moistened cloth only, do not use
scouring or abrasive detergents.
6
Appliance interior
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Upper utensils basket
Additional cutlery basket * for the
top basket
Additional cup rack *
Upper spray arm
Lower spray arm
Dispenser for salt
Filters
Cutlery basket
Lower utensils basket
Lock
Dispenser for rinse aid with refill
display
Detergent dispenser
Optical limescale sensor
Rating plate
* some models
en
Before using your appliance for the first time
Before you can use your appliance for the first time, you must select the language. When
the appliance has been switched on, the following display is output:
M
OK
–
<
DE EN FR NL IT EL
>
+
The language abbreviation “DE” for
“Deutsch” (German) is flashing. If you
want to select a different language,
press – or + 3 repeatedly until the
abbreviation of your desired language
flashes.
Confirm the language selection by
pressing M/OK 2 .
All following optical character messages
will be displayed in the selected language.
Providing operating materials
Chosen the wrong language
Before using the appliance for the first time
and after selecting the language, fill with
salt (if required) and rinse aid and adjust
the softening system. Proceed as
described in the chapters “Filling with salt”,
“Filling with rinse aid” and “Adjusting the
softening system”.
The following steps will take you back
to the language selection:
1. Switch off the device.
2. Switch on the device. Press the button
M/OK 2 until the language selection
is displayed.
3. Select the desired language and
confirm your selection.
To operate the dishwasher you will require
salt (only for appropriate water
hardness, see chapter “Adjusting
the softening system”),
rinse aid,
detergent.
Only use products which are suitable
for the dishwasher.
7
en
Filling in the Salt
Note
If the hardness of your mains
water corresponds to the
(see
device’s index value
chapter “Setting up the softening
system”), you do not need to fill
in the salt because the operation
will not use any salt. In case of
the settings “Hardness-Auto” and
to , salt must be filled in.
During the rinse cycle the salt is being
washed automatically from the salt
compartment into the softening system
where it will dissolve the lime.
The lime-containing solution drains from
the dishwasher. Afterwards the softening
system is ready to be loaded again.
This regeneration cycle will only work if
the salt is dissolved in water.
After switching on the device, lack of salt
is indicated by the display “Refill Salt”.
(This display will no longer appear once
you have set the softening system to the
value .)
Open the screw-type cap of the
compartment 25 .
Before operating the device for the first
time you must pour 1 litre of water into
the salt compartment.
8
Then you must refill salt (not table salt)
using the supplied salt filling aid until the
salt compartment is full (max 1.5 kg).
When you refill the salt, water is being
displaced and drains off. Therefore the
refilling must take place shortly before
switching on the device. (In order to avoid
corrosion). This way the overflowing salt
solution is diluted and flushed immediately.
Then clean the filling area of salt residues
and screw the compartment lid back on
without tilting the lid.
As soon as a sufficiently high salt solution
has formed the display “Refill Salt” will
disappear.
If you do not want to wait until the display
disappears but you want to wash
immediately, confirm the refilling of the salt
using the button M/OK 2 .
If you do not want to refill the salt now you
can skip the display “Refill Salt” by
pressing the button M/OK 2 .
Do not pour detergent into the
container for special salt. This
would destroy the water
softener.
en
Setting up the water
softener
In order to provide satisfactory rinsing
results, the dishwasher requires soft water,
i.e., containing little or no lime, otherwise
water stains will be left behind on the
dishes and interior containers.
If the tap water exceeds a certain level of
hardness, it must be softened, i.e.,
decalcified, so that it can be used in the
dishwasher.
This is achieved by adding a special salt
to the water softener inside the
dishwasher.
The water softener, that is the required
amount of salt, is set up according to how
hard the tap water is.
The softening system is only capable to
accept a limited amount of lime. If this
limit is reached the system must be
regenerated or refreshed using salt.
The factory setting “Hardness-Auto” allows
the deposit sensor to determine the
hardness and to control the softening
system automatically. This means that
changes to the settings are unnecessary
during start-up or in case of changes in
the water hardness.
If you would nevertheless like to set
the water softening system manually,
proceed as follows:
Find out the degree of hardness of your
tap water. Your water supply company
or customer service will assist you.
Switch on the appliance with the main
switch 1 . The main menu is
displayed (if switching on the appliance
for the first time, only when a language
has been selected and dispensers
have been filled with salt (if required)
and rinse aid).
Press the button M/OK 2 until
“Hardness-Auto” is displayed.
Using the buttons – or + 3 , select the
setting corresponding to the hardness
of your mains water. The factory setting
is “Hardness-Auto”.
Press the button M/OK 2 to store the
setting and return to the Main Menu.
If the setting is “0” the softening system is
switched off. Possible lack of salt will not
be indicated.
9
en
Filling with rinse aid
Rinse aid is used in washing mode to
ensure that glasses are sparkling and
utensils are stain-free.
When the appliance is switched on, low
rinse aid level is indicated by ”Refill rinse
aid”. You can add rinse aid either when the
appliance door is completely open or – for
a more comfortable posture – when the
door is half open.
Open the rinse aid dispenser 30 by
pressing the button on the dispenser
cover and open the cover. When the
door is half open, also pull out the
hinged filling aid until it locks into
position.
If necessary, you can change the amount
of rinse aid that is added during the
operation. In order to do this, select the
option “Rinse Aid Amount” as described
in the chapter “Device Set-up” under
the heading “Options/Basic Settings”.
rinse–aid control
Fill when door is fully open.
Fill in the rinse aid slowly and take care
not to overfill. The right amount is
indicated by the level indicator at the
compartment not being illuminated
when the door is fully opened and by
the display “Refill Rinse Aid” no longer
being lit.
Close the lid of the compartment until it
audibly clicks into place. If necessary,
the filling aid will be re-inserted
automatically.
If you want to fill in the rinse aid at a later
time you can skip the display “Refill Rinse
Aid” by pressing the button M/OK 2 .
10
Filling when the door is half open.
Note
Use only rinse aid for domestic
dishwashers. Spilt rinse aid
may result in excessive foam
formation in the next rinse
cycle. Therefore, remove any
spilt rinse aid with a cloth.
en
Unsuitable dishes
You should not clean the
following items in your
dishwasher:
Cutlery and dishes made of wood. They
will leach out and become unsightly; the
utilised adhesives are also not suitable
for the dishwasher temperatures.
Delicate décor glasses, craft dishes and
vases, special antique or irreplaceable
dishes. These décor items are not
dishwasher-safe.
Plastic parts, copper and tin dishes
sensitive to hot water are not suitable
either. Overglazed patterns, aluminium
and silver parts tend to become
discoloured and fade during the rinsing
cycle. Even some types of glass (e.g.
crystal glass objects) may become cloudy
after many rinse cycles. Completely
absorbent materials, such as sponges and
cloths must not be cleaned in the
dishwasher either.
Recommendation:
In future buy only dishes which are
identified as dishwasher-safe.
Damage to glassware and other
dishes
Possible causes:
type of glass or manufacturing process
chemical composition of detergent
water temperature and duration of
dishwasher programme.
Suggested remedy:
Use glassware or porcelain dishes that
have been marked ’dishwasher–proof’
by the manufacturer.
Use a mild detergent that is described
as ’kind to dishes’. If necessary, seek
further information from detergent
manufacturers.
Select a programme with as low a
temperature and as short a duration as
possible.
To prevent damage, take glass and
cutlery out of the dishwasher as soon
as possible after the programme has
ended.
Note
Dishes which are soiled with
ash, wax, lubricating grease or
ink must not be cleaned in the
dishwasher.
11
en
Arranging crockery, glasses,
etc. in the dishwasher
Pots and pans
Lower basket
28
Loading the dishwasher
Scrape off any large amounts of left-over
food. It is not necessary to rinse the dishes
under running water.
Place objects in the dishwasher in such a
way that
items such as cups, glasses, pots/pans,
etc. are stood upside down,
curved items, or those with recesses,
should be at a slant so that water can
run off,
they are stacked securely and cannot
tip over,
they do not prevent the spray arms from
rotating while washing takes place.
Very small items should not be washed in
the dishwasher as they could easily fall out
of the baskets.
Cutlery
Cups and glasses
Cutlery should be placed in the
dishwasher always unsorted and with the
eating surface pointing downwards. The
spray jet is then better able to reach the
individual parts.
To prevent injuries, place long, pointed
accessories and knives on the étagère
(some models) or on the knife shelf
(available as an accessory).
Upper basket
Folding spikes *
Removing the dishes
To prevent water dripping from the top
basket onto the dishes in the lower basket,
we recommend that you empty the lower
basket first and then the top basket.
20
* on applicable models
To improve stacking of pots and pans, the
spikes can be folded down.
* on applicable models
12
en
Baking sheet spray head *
Shelf *
* some models
You can clean large baking sheets or
grilles with the baking sheet spray head.
To do this, remove the top basket and
insert the spray head as illustrated in the
diagram.
* not on all models
Lean tall glasses and those with long
stems against the shelf – not against other
items to be washed.
Long items, serving cutlery, salad servers
or knives should be placed on the shelf so
that they do not obstruct the rotation of the
spray arms. The shelf can be folded back
when not required for use.
Small accessories holder*
To ensure that the spray jet can reach all
parts, arrange the baking sheets as
illustrated
(max. 4 baking sheets and 2 grilles).
* some models
Light-weight plastic accessories, e.g. cups,
lids, etc. can be held securely in the small
accessories holder.
13
en
Adjusting position of basket *
* not on all models
Top basket with side levers
(Rackmatic)
Pull out the top basket.
Ø max.
20/*25cm
86cm
81cm
Ø max.
20/*25cm
Ø max.
30/*25cm
Ø max.
34/*29cm
If required, the height of the top basket can
be adjusted in order to create more space
for large utensils either in the top or bottom
basket.
Select one of the two following procedures
according to the design of the top basket
for your appliance model:
Top basket with upper
and lower roller pairs
Pull out the top basket.
Remove the top basket and re-attach it
to the upper or lower rollers.
14
To lower the basket, press in
succession the two levers on the left
and right sides of the basket. Always
take hold of the side of the basket on
the upper edge, otherwise the basket
will not drop smoothly (and may
damage the utensils).
en
Detergents
Notes on detergents
You may use any brand of liquid or powder
detergent, as well as tablets, that have
been specifically designed for use in
domestic dishwashers (do not use normal
washing-up liquid!).
To raise the basket, take hold of the
basket on the upper edge and pull
upwards.
Before you re-insert the basket, ensure
that it is at the same height on both
sides. Otherwise, the appliance door
cannot be closed and the upper spray
arm will not connect to the water circuit.
Nowadays there are three types of
dishwasher detergent available:
1. Those containing phosphates
and chlorine.
2. Those containing phosphates
but no chlorine.
3. Those containing neither phosphates
nor chlorine.
When a phosphate-free detergent is used
in conjunction with hard water, there is
a greater possibility that white marks will
be left behind on the dishes and glasses,
etc.
These can be prevented by pouring an
increased amount of detergent into the
dispenser.
Chlorine-free detergents have a reduced
bleaching effect. This may mean that tea
stains are not completely removed or
plastic items become discoloured.
This can be resolved by:
– using the “Auto Super Wash”
programme
– increasing the amount of detergent
– using a detergent that contains chloride
Check the label on the packaging to
determine whether a particular product is
suitable for use with silverware.
If you have any further questions, we
recommend that you contact the customer
advice departments of the respective
detergent manufacturer.
15
en
Detergent dispenser with
dosing aid
The graduated detergent dispenser helps
you add the correct amount of detergent.
The lower and middle lines in the
dispenser indicate15 ml and 25 ml of
detergent respectively. The dispenser can
be filled with 40 ml of detergent when the
door is opened horizontally.
Filling with detergent
You can add detergent either when the
appliance door is completely open or –
for a more comfortable posture – when
the door is half open.
If the detergent dispenser is still closed,
.
open it by pressing the catch
When the door is half open, press the
button on the right side of the detergent
dispenser. Swivel up the detergent
compartment and cover. The detergent
compartment can easily be locked into
position by lifting it slightly.
16
Pour detergent into the dispenser.
Please follow the manufacturer’s
instructions on the detergent packet
for correct dosage.
Due to the different solvency properties
of the detergent tablets supplied by
various manufacturers, the cleaning
efficiency of the detergent may not be
fully utilised by short programmes. It is
recommended to use washing powder
for these programmes.
For the “Auto Super Wash” function,
pour an additional 10–15 ml of
detergent onto the inside of the
appliance door.
en
Reduce costs!
If your dishes are only
moderately dirty, you may be
able to use less detergent than
recommended.
If using washing tablets, please refer to
the washing tablets box where to place
the tablets in the appliance (e.g. in the
cutlery basket, detergent dispenser).
Close the detergent dispenser. Slide
the dispenser cover completely over
the detergent compartment (1) and then
press down firmly (2) until the catch
“clicks” into position.
Opening and closing
the door
To open the door, pull the door handle.
To close the door, press the door shut
until it “clicks” into position.
The door can be easily opened before
the wash programme starts and when the
programme ends.
Close the detergent dispenser when the
door is completely open.
Close the detergent dispenser when
the door is half open.
During the washing cycle the cover of
the detergent dispenser is automatically
opened and the detergent is washed
out. The cover is therefore open when
the programme ends.
17
en
serve@Home *
* on applicable models
This dishwasher is serve@Home capable.
serve@Home is a network comprising
other serve@Home domestic appliances
besides dishwashers. Through it the
device offers you greater comfort and
mobility, at home as well as on the road.
In order for your dishwasher to become
serve@Home capable, you will need a
special accessory, the System Interface.
You can purchase this interface from your
specialist supplier. The interface must be
mounted in the chamber at the front of the
dishwasher following the installation
instructions supplied with the system
interface.
When you select your dishwasher’s mode
“Remote Control: On” you can remotely
control the device.
You can set up and start the prepared,
switched on, and closed dishwasher if you
are not at home. Equally, you can switch
off your dishwasher at any time, even if the
device is not in the Remote Control Mode.
18
Status Inquiry
You can check the current status of your
dishwasher at any time.
Remote Control
The serve@Home system allows you to
select the programme and to start the
dishwasher. To take advantage of this
service you must set the dishwasher’s
mode to “Remote Control: On”.
Advice and Warning Messages
These messages can be transmitted from
your dishwasher to your operating unit.
Remote Diagnosis
You can transmit error messages to the
Customer Support, thereby helping in the
diagnosis.
en
Adjusting the appliance
auto 3in1
Switching on the appliance
Turn on the tap fully.
Switch on the appliance with the main
switch 1 and, if required, top up with
salt and rinse aid (see chapters “Filling
with salt”, “Filling with rinse aid”). The
main menu is then displayed.
<
Auto Wash
>
After switching on the Main Menu shows
the programme “Auto Wash”.
Setting the Programme
From the programme “Auto Wash” in the
Main Menu you can select among the
following programmes:
“Auto Super Wash” –
“Auto Wash” –
“Auto Delicate Wash” –
“Short Rinse” –
“Prerinse Only”.
Set the desired programme by using
the buttons – or + 3 .
The auto programmes “Auto Super Wash”,
“Auto Wash”, and “Auto Delicate Wash”
automatically match the programme to the
amount and soil level of the dishes. This
keeps the energy and water consumption
as low as possible.
Using the following programme overview
you can select the appropriate programme
for the type, amount, and soil level of the
dishes.
The use of so-called combined detergent
products may make the use of rinse aid
and/or salt unnecessary.
There are currently several types of
combined detergent products available.
3in1: They contain detergent, rinse aid
and salt function.
2in1: They contain detergent and rinse
aid or salt function.
>>> Always check the type of detergent
or combined product which you
are using!
Always follow the operating instructions
or the information on the packaging.
The rinse programme is automatically
adjusted in order to obtain the best
possible rinsing and drying result.
Observe the following important
information if using combined cleaning
products:
Regeneration salt is not required up to
a water hardness of 21 dH (37 fH,
26 Clarke, 3.7 mmol/l) only. No other
settings on the appliance are required.
Salt is still required if the water
hardness is above 21 dH (37 fH,
26 Clarke, 3.7 mmol/l). Fill the salt
dispenser with salt 25 .
The factory-set hardness setting
“hardness auto” ensures that the water
softening system is set optimally by
the optical limescale sensor even if
combined cleaning products are used.
19
en
If in doubt, please contact the detergent
manufacturer, especially if:
the utensils are very wet at the end
of the programme.
limescale forms.
Note
Optimum rinsing and drying results can be
obtained by using standard detergents in
conjunction with separate application of
salt and rinse aid.
Observance of the operating instructions
or information on the packaging of the
combined detergents determines their
effectiveness.
If the “Add rinse aid or special salt” display
is defective, you can switch it off as
follows:
Switching “Add rinse aid”
off and on:
Switch on the appliance with the main
switch 1 .
Keep pressing button M/OK 2 until
the “rinse aid 4” setting is displayed.
By pressing buttons – or + 3 ,
you can select a set value between
0 and 6. To switch off, select position “0”
Press button M/OK 2 . The set value
is saved and you are returned to the
Start menu.
If the set value “0” is selected, rinse aid
is not dispensed. Low rinse aid is not
displayed.
20
Switching “Add special salt”
and therefore the water
softening system off and on:
Switch on the appliance with the main
switch 1 .
Keep pressing button M/OK 2 until
the “hardness auto” setting is displayed.
By pressing buttons – or + 3 ,
select a set value between 0 (off) and 7.
The factory setting is “hardness auto”.
To switch off, select position “0”
Press button M/OK 2 . The set value
is saved and you are returned to the
Start menu.
If the set value “0” (off) is selected, the
water softening system is switched off.
Low salt is not displayed.
Note
If you use the detergent and rinse aid
separately or switch from combined
detergents to standard cleaning products,
ensure that the rinse aid dispenser amount
has been switched on and the water
softening system has been set to the
correct water hardness or to “hardness
auto”.
en
Programme overview
Type of utensil
e.g. porcelain,
pans,
cutlery,
glasses,
etc.
Type of food
remains
e.g.
Hardwearing
Soups,
soufflés,
sauces,
potatoes,
pastries,
rice, eggs,
fried food
Amount of
food remains
Fragile
Very
adhesive
Wash
programme
AUTO
SUPER
WASH
60 – 70
Mixed
Coffee,
cake, milk,
sausage, cold
drinks,
salads
Soups,
potatoes,
pastries,
rice, eggs,
fried food
Rinse if the
utensils have
been left for
several days
prior to washing in the dish
washer
Very
small
Large -> small
Condition of
food remains
Programme
progress
Mixed
Slightly adhesive
AUTO WASH
45 – 55
AUTO
DELICATE
WASH
35 – 45
QUICK
WASH
PRERINSE
ONLY
45
Prerinse
The programme progress is
optimised and adjusted
according to the appliance
load and degree of soiling
on the utensils.
Clean
Intermediate wash
Final wash
Drying
21
en
Programme data
The programme data (duration, energy
and water consumption) can be found in
the summary of instructions and refers to
standard conditions. Greater deviations
may be caused by:
different quantities of utensils
inlet temperature of the water
water pressure
ambient temperature
mains voltage tolerances
and appliance-specific tolerances
(e.g. temperature, water flow rate, etc.)
Only ranges can be indicated for the
automatic programmes.
The water consumption values refer
to water hardness value 4.
22
Selecting options/
standard settings
Operating principle
From the Main Menu you can select the
following options/settings by repeatedly
pressing the button M/OK 2 :
Time Pre-select
Remote Control **
Reduce Time
Drying Level
Buzzer Volume
Adding Rinse Aid
Water Hardness
Language
Standard Programmes
Remote Setting **
** Only with installed serve@Home
interface
Within an option/basic setting there are
several possible settings that can be
selected using the buttons – or + 3 .
A selected setting is applied by
changing to the next option/basic
setting using the button M/OK 2 .
If a setting has been changed using the
buttons – or + and stored using M/OK
2 , the message “Value stored” will be
displayed and the display returns to the
Main Menu.
en
Time Pre-select
Reduce Time
You can delay the programme start by
24 hours in steps of 30 minutes.
If the option “Time Pre-select” is chosen
the display shows ”Delay Start:
00 mins”.
Set the desired time.
Return to the Main Menu by pressing
M/OK 2 and start the required
programme by pressing the Start Button
5 .
Close the door. This starts the time
counting backwards.
When the set time has elapsed the
programme will start automatically.
Until the programme starts you are able
to change the set time and programme.
To do this, use the button – 3 to
return to the Main Menu and change
the settings. Then start the programme
again.
In order to delete the pre-selected time,
set the time back to “Delay Start:
00mins”.
The Auto Programmes allow you to reduce
the run time of the programmes. However,
in order to achieve an optimal cleaning
result, the water and energy consumption
will be increased.
If the option “Reduce Time” is chosen
the display shows “Reduce Time: Off”
(factory setting).
Select “Reduce Time: On”.
Return to the Main Menu by pressing
M/OK 2 and start the required
programme by pressing the Start Button
5 .
If you do not want to use “Reduce
Time” the next time you use the
dishwasher, you must deselect this
option.
Remote Control **
After choosing the option “Remote
Control” the display will show “Remote
Control: Off” (factory setting)
You activate this option by selecting
“Remote Control: On”.
** Only with installed interface
Drying Level
If the option “Drying Level” is chosen
the display shows “Normal Drying”
(factory setting).
Alternatively, you can choose
“Save Drying” or “Extra Drying”.
The option “Extra Drying” increases the
temperature during rinsing in all
programmes. (Please take care with
delicate dishes.)
Buzzer Volume
You can modify the volume of the acoustic
signals or even turn it off altogether.
If the option “Buzzer Volume” is chosen
the display shows “Buzzer 6” (factory
setting).
You can change this value to 0
(acoustic signals switched off) or to
values between 1 (quiet) and 6 (loud).
A short buzz demonstrates the currently
chosen volume level.
23
en
Adding Rinse Aid
Language
You can set the amount of rinse aid
added.
If the option “Adding Rinse Aid” is
chosen the display shows “Rinse Aid 4”
(factory setting).
Change this setting only if there are
streaks (reduce the value) or water
stains (increase the value) remaining
on the dishes.
You can choose a value between 0
and 6.
You can change the language selected
when the appliance was started for the first
time (see chapter “Before Starting The
Device For The First Time”).
If the option “Language” is chosen the
display shows several language
abbreviations. The abbreviation of the
currently selected language is flashing.
In order to choose a different language,
press – or + 3 until the desired
language appears.
Confirm the language selection by
pressing M/OK 2 .
All subsequent optical character
messages will be displayed in the selected
language.
Water Hardness
The factory setting “Hardness-Auto” allows
the deposit sensor to determine the
hardness and to control the softening
system automatically. This means that
changes to the settings are unnecessary
during start-up or in case of changes in
the water hardness.
24
en
Standard Programmes
In addition to the rinse programmes
available in the Main Menu you can
choose among the following standard
programmes from the programme
“Normal”:
Extra,
Eco,
Normal,
Plus.
Set the desired programme and start
the selected programme by pressing
the Start Button 5 .
If you do not want to use any of the
displayed standard programmes return
to the Main Menu by using the button
M/OK 2 .
If you want to cancel the selection of
a standard programme in the Main
Menu press the button – “Back”. The
selected standard programme will be
displayed. By pressing the buttons –
or + the Main Menu will display the
programme “Auto Wash”.
Extra
Eco
Normal
Type of Dishes
Mixed Dishes
Amount of
Food Particles
Little to Many
State of
Food Particles
Lightly Adhesive
Plus
You can find the corresponding programme data (length of time, energy and water
consumption) in the short manual.
We recommend on principle to use the Auto Programmes because they keep the
water and energy consumption as low as possible due to the variable programme run.
In the case of the standard programmes on the other hand, the programme run is
predetermined.
25
en
Remote Options **
Start programme
The dishwasher installs itself automatically
during the first use within a serve@Home
network. In some cases however, it might
become necessary to start the enrolment
process anew.
If the option “Remote Options” is
selected, the message “Enrol Device”
will be displayed. By pressing the
button + 3 you enrol the device
again at the gateway. After successfully
enrolling the device the message
“Auto Wash” will be displayed.
If the enrolment is unsuccessful the
display shows “no gateway found”.
** Only with installed interface
Before starting check again whether the
spray arms can move freely.
Press the button “Start” 5 in the Main
Menu.
The message “Close the door” will be
displayed, alternating with a display of the
expected programme time. This time
is only approximate. At programme start
it corresponds to the time the programme
ran the last time. During the programme
run the remaining time will be adjusted
according to the water supply temperature
and the amount and soil level of the
dishes.
If you have chosen a time for the
programme start the message “Close
Door” will appear when the programme is
started, alternating with the pre-selected
time.
Close the door.
The programme or the pre-selected time
respectively will run.
The programme and other settings can still
be changed as long as the door is still
open after pressing the button “Start” 5 .
By pressing the button M/OK 2 “Back”,
return to the Main Menu where you can
change the settings. Finally start the
programme again.
When the door is closed after the start
and the programme has already started,
you will have to interrupt the programme in
order to change any settings (see “Cancel
Programme”).
Aqua sensor *
* on applicable models
The Aqua sensor is an optical measuring
device which measures the turbidity of the
rinsing water. A light barrier can detect
dissolved food remnants in the water, e.g.
egg, fat and oats.
The Aqua sensor is used according to
the programme. When the Aqua sensor
is active, ”clean” rinsing water may be
transferred into the next rinsing bath
and/or the temperature adjusted. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In this
way the water consumption is reduced by
approx. 4 litres for utensils which are ”less”
dirty.
Optical indicator during
operation *
* With some models
During the rinse programme a light point
appears on the floor below the device’s
door. Only open the dishwasher door
when the light point has disappeared.
In the case of built-in dishwashers with
flush front the light point will not be visible.
26
en
Cancel Programme
In order to interrupt the programme,
open the door. In order to avoid water
escaping, only open the door slightly
first.
The message “Cancel Programme”
will be displayed, alternating with
the message “Close the door”,
the remaining programme time, the
selected programme, and the current
programme phase.
In order to interrupt, do not in any
circumstance press the button – 3
“Cancel Programme” because this will not
allow the programme to continue!
To continue the programme, close the
door. The programme will continue
automatically.
In the case of a warm water supply or
when the appliance is already heated,
leave the door slightly ajar for a few
minutes before closing it. Otherwise the
door can spring open again due to the
warm air trapped in the device’s interior.
Cancelling active programme
Open the door. First open the door only
slightly in order to avoid water spraying
out.
The message “Cancel Programme” will
be displayed, alternating with the
message “Close the door”, the
remaining programme time, the
selected programme, and the current
programme phase.
In order to cancel the programme,
press – 3 “Cancel Programme”.
The display shows “To drain Close
the door” with the message “Close the
door” flashing.
Close the door. The water remaining in
the device’s interior will be pumped off.
Once the pumping off has finished
a buzzer will sound 5 times.
Open the door. “Ready” is briefly
displayed, the appliance automatically
switches off after 5 seconds.
End of the programme
As soon as the programme has finished
a buzzer will sound 5 times.
Open the door. “Ready” is briefly
displayed, the appliance automatically
switches off after 5 seconds.
If the door is not opened, the appliance
automatically switches off after one
hour. During this time the acoustic
signal sounds every 15 minutes.
After letting the device cool down take
out the dishes.
When the programme has finished you
can switch off the appliance or start it
again.
Note
For an optimum drying of the dishes wait
for 15 minutes after the programme has
finished before you open the door and
empty the dishwasher. During this time the
possibly remaining water on the dishes
can evaporate and condense on the sides
of the device’s interior.
Note
If the device becomes disconnected from
the power supply during operation (e.g.
it is switched off or there is a power cut),
all settings remain stored. Operation will
resume automatically once the power
supply has been restored.
27
en
Maintenance and care
You can help prevent faults by checking
and maintaining your appliance regularly.
This will save time and reduce problems.
Therefore you should occasionally
examine the inside of your dishwasher.
Overall condition of the
appliance
Check the rinsing compartment for grease
and limescale deposits.
If you find any deposits:
Fill the detergent dispenser with
detergent. Start the empty appliance
with the programme which has the
highest rinsing temperature.
Clean the door seal:
Wipe the door seal regularly with
a damp cloth and remove any deposits.
Special Salt
When the salt level is low, your
dishwasher displays a message in the
window.
Rinse aid
When the rinse aid level is low, your
dishwasher displays a message in the
window.
Filters
The filters 26 prevent larger remnants of
food or other objects from getting inside
the pump. This residue can occasionally
clog up the filters.
The filter system consists of a filter
cylinder, a flat fine filter and, depending on
the model, a microfilter (*).
Inspect the filters for obstructions every
time the dishwasher has been used.
By unscrewing the filter cylinder, you
can remove the filter system. Remove
any food remnants and clean the filters
under running water.
28
Reassembly:
Insert the filter system and screw down
with the filter cylinder.
en
Spray arms
Lime and remnants of food in the washing
water can block the nozzles in the spray
arms 23 and 24 and the arm
mountings .
Inspect the nozzles in the spray arms
for blocked holes due to remnants of
food.
If necessary, pull the lower arm 24
upwards and lift it off.
Unscrew the upper spray arm 23 .
Clean both spray arms under running
water.
Refit the spray arms. Ensure that the
lower arm has locked into place and the
upper one is screwed tight.
Pump *
* on applicable models
Larger remnants of food that have not
been trapped by the filters and have been
left in the water can cause a blockage in
the pump. The water is no longer pumped
out of the dishwasher and it can be seen
covering the filter.
Proceed as follows:
Ladle out as much water as possible.
Remove the filters 26 .
Undo the screw in the cover (Torx T 20)
and remove the cover.
Inspect the inside and remove any
obstructions that you find.
Re-insert the cover and screw down.
Re-insert the filters and screw down.
Torx T20
2
1
3
2
1
0
Spray arms
29
en
Fault finding
Resolving minor problems
yourself
Experience has shown that you can
resolve most problems that arise during
normal daily usage yourself, without
having to call out a service engineer. Not
only does this save costs, but it also
means that the appliance is available for
use again that much sooner. The following
list of common occurrences and their
remedies should help you identify the
causes of most problems.
Problems ...
... On Switching On
Wrong Language Selected
The following steps return you to the
language selection:
1. Switch off the device.
2. Switch on the device. Press the button
M/OK 2 repeatedly until the
language selection appears in the
display.
3. Select the language and confirm your
selection.
The device does not start.
A fuse in the house is defect.
The device is not properly
plugged in.
The device’s door is not closed
properly.
The device’s door was closed
without first starting the
programme.
30
Some time after the programme
start a continuous acoustic signal
sounds.
The device does not draw water.
When the door is opened the
message “Check water supply”
is displayed.
Mains water tap is not opened.
Open the tap fully and press the
button M/OK 2 of the device.
Then close the device’s door for
the programme to resume.
Filter of the water inlet hose is
blocked.
Switch off the device and
disconnect it from the power
supply. Close the mains water tap.
Clean the filter located at the
connection of the Aquastop or the
inlet hose. Finally, restore the
power supply. Open the mains
water tap, switch on the device,
and close the door for the
programme to resume.
Attention
Please remember: Repairs
may only be carried out by
professionals. Unprofessional
repairs can cause significant
damage and danger to the
user.
en
... with the appliance itself
Lower spray arm rotates with
difficulty
Spray arm is blocked by small
items or food remains.
Lid in detergent compartment
cannot be closed
Detergent compartment has been
overfilled.
Mechanism is clogged with
remnants of detergent.
Indicator lamps do not extinguish
after washing has finished.
Remnants of detergent stuck inside
dispenser
Compartment was damp when it
was filled up with detergent.
Compartment must be dry before
detergent is added.
Refill display does not light up.
Rinse aid refill indicator switched
off. (see auto 3in1 chapter)
Salt refill indicator switched off.
(see auto 3in1 chapter)
At the end of the programme there
is still water in the appliance.
The waste water hose is blocked
or kinked.
The waste water pump is blocked.
The filters are blocked.
The programme has not yet
ended. Wait until the programme
ends or terminate the programme.
... during washing
Unusual amount of foam is created
Normal washing up liquid has
been poured into the rinse-aid
container.
Remove any spilled rinse aid with
a cloth as it could otherwise lead
to excessive foaming during the
next washing cycle.
Appliance stops suddenly while
washing is taking place
Cut in electricity supply to
appliance.
Water supply has been
interrupted.
Knocking sound can be heard
while washing is taking place
A spray arm is knocking against
the dishes inside the appliance.
Rattling sound can be heard while
washing is taking place
Crockery has not been stacked
properly inside the appliance.
Knocking sound coming from inlet
valves
This is caused by the way the
water pipes have been laid and it
has no effect upon the way the
appliance functions. There is no
remedy for this.
... with the dishes, cutlery, etc.
Remnants of food are stuck to the
dishes, cutlery, etc.
Dishwasher was not loaded
properly. Jets of water could not
reach all parts of the dishes, etc.
Too many items in the rack.
Items in the rack were touching
each other.
Not enough detergent was added
to dispenser.
Selected wash programme was
not intensive enough.
Rotation of spray arm was
obstructed by dish, etc.
Nozzles in spray arm are blocked
by remnants of food.
Filters are blocked.
Filters have been incorrectly fitted.
Waste-water pump is jammed.
31
en
Plastic items are discoloured
Not enough detergent was added
to dispenser.
White stains are left on crockery,
glasses have a milky appearance
Not enough detergent was added
to input compartment.
Amount of rinse-aid was set too
low.
Although water is quite hard, no
salt has been put in appliance.
Water softener was set too low.
Lid on salt container is not
screwed tight.
If you used a phosphate-free
detergent, try a detergent
containing phosphates and
compare results.
Dishes, cutlery, etc. have not been
dried
Selected programme did not
include drying function.
Amount of rinse-aid was set too
low.
Items were removed from
dishwasher too soon.
Glasses have a dull appearance
Amount of rinse-aid was set too
low.
Tea stains or traces of lipstick have
not been completely removed
Detergent does not have a
sufficient bleaching effect.
Washing temperature was set too
low.
Traces of rust on cutlery
Cutlery is not sufficiently rustproof.
Salt content in washing water is
too high.
Lid on salt container is not
screwed tight.
Too much salt was spilt while
filling container.
32
Glasses become clouded and
discoloured; coating cannot be
wiped off
Unsuitable detergent was used.
Glasses are not dishwasher-proof.
Smears left behind on glasses and
cutlery; glasses have acquired a
metallic appearance
Amount of rinse-aid set too high.
... serve@Home
The dishwasher cannot be
operated via serve@Home.
The device is not connected to
the network.
The device is not ready for
serve@Home.
The System Interface is not
installed.
en
Customer Service
Please call your local service agent, if you
are not able to resolve any problem
yourself. The name of your nearest service
agent is shown in the Customer Service
address list. When you call, please provide
details of the model number (1) and the
production (FD) number (2) which are
shown on the nameplate on the appliance
door.
1
FD
2
Warning
Please note that a visit by the
customer service technician in
the event of a fault or one of
the problems previously
discussed is not free of charge
even during the warranty
period.
Notes
Disposal of your old appliance
Old appliances are not worthless rubbish.
Valuable raw materials can be reclaimed
by recycling old appliances.
Pull out the mains plug of the redundant
appliance. Cut off the power cord and
discard with mains plug.
To prevent children from locking
themselves in the appliance and
suffocating, destroy the door lock
and childproof lock (if fitted).
You received your new appliance in
a protective shipping carton. All packaging
materials are environmentally friendly and
recyclable. Please contribute to a better
environment by disposing of packaging
materials in an environmentally-friendly
manner.
Please ask your dealer or inquire at your
local authority about current means of
disposal.
Keep children away from the shipping
carton and packaging components.
Danger of suffocation from folding cartons
and plastic film.
Notes on comparison tests
You will find details of the conditions for
the comparison tests on the additional
”Notes on comparison tests” sheet. The
consumption values for the relevant
programmes are given in the introduction.
33
en
General
Built-under and integrated appliances
which are subsequently installed as
free-standing appliances must be
secured to prevent them from falling
over, e.g. by screwing them to the wall
or by installing them under a continuous
worktop which is screwed to the
adjoining units.
For Swiss version only:
The appliance can be installed without
difficulty between wooden and plastic
walls in a kitchen range. If the appliance
is not connected via a plug, the
installation side must feature an all-pole
disconnector with a contact gap of at
least 3 mm in order to satisfy the
relevant safety regulations.
Installation
The dishwasher must be connected by
a qualified technician to ensure correct
operation. The specifications for supply,
drainage and connected load must fulfil
the required criteria as stated in the
following paragraphs or in the installation
instructions.
Install the appliance in the following
sequence:
– Check the delivery
– Install the appliance
– Connect the waste water
– Connect the fresh water
– Connect the power supply
Delivery
Your dishwasher was checked at the
factory to ensure that it was in perfect
working order. This may have left some
small water stains in the dishwasher.
These will disappear after the first rinse
cycle.
Installation
The required installation dimensions can
be found in the installation instructions.
Using the height-adjustable feet, adjust the
appliance until it is level. Ensure that the
appliance is standing firmly.
Waste water connection
See the installation instructions for the
required connection steps. If required,
attach a siphon with drainage spigot.
Using the enclosed parts, connect the
waste water hose to the drainage spigot
of the siphon.
Ensure that the drainage hose is not
kinked, crushed or twisted (ensure that
there is no sealing cover which prevents
the waster water from flowing away!).
34
en
Fresh water connection
Removing the appliance
Using the enclosed parts, connect the
fresh water connection to the tap
according to the installation instructions.
Ensure that the fresh water connection is
not kinked, crushed or twisted.
When replacing the appliance, always
connect a new water supply hose to the
water supply. The old supply hose must
not be re-used.
Water pressure:
Minimum 0,05 MPa (0,5 bar) – maximum
1 MPa (10 bar).
If the water pressure is higher, install a
pressure reducing valve.
Flow rate:
Minimum of 10 litres per minute.
Water temperature:
We recommend that you use cold water.
If you do use hot water, the temperature
should not exceed 60 °C.
It is essential, when removing the
appliance, to observe the following
sequence: First, disconnect the appliance
from the power supply.
Pull out the mains plug.
Turn off the water supply.
Disconnect the waste water and fresh
water connections.
Loosen the fastening screws under the
worktop. If fitted, remove the base panel.
Pull out the appliance, carefully pulling the
hose behind.
Electrical connection
Connect the appliance only to 230 V
alternating current via a correctly installed
socket with protective conductor.
See rating plate for required fusing 33 .
The socket must be attached near the
dishwasher and be freely accessible.
The connection may be modified by an
electrician only.
Use only a residual-current-operated
circuit-breaker which features the
symbol. Only this circuit breaker
guarantees compliance with the currently
valid regulations.
Transportation
Empty the dishwasher according to
the following steps:
Turn on the tap.
Switch on the appliance.
Start any automatic programme
and close the appliance door.
Wait until approx. 4 minutes have
elapsed.
Then open the door, terminate
the programme and close the door
to drain the appliance.
Wait until the buzzer is emitted 5 times,
i.e. all the water has been drained.
Switch off the appliance.
Turn off the tap.
Secure loose parts prior to transportation.
Transport the appliance upright only.
Otherwise, residual water may penetrate
the control and damage the appliance.
Protection from freezing
temperatures
If the appliance is installed in a location
where there is a risk of freezing
temperatures (e.g. in a holiday home), all
water must be completely drained out of
the interior (see “Transporting the
dishwasher”).
Turn OFF the tap, disconnect the supply
hose and allow to drain.
35
en
en
36
Subjekt to modification
016 #22.+%#$.' 61 #22.+#0%'5 9+6*176 37#>612
0 #&&+6+10 61 9#44#06; %.#+/5 #)#+056 6*' 5'..'4 $#5'& 10 6*' 5#.'5 #)4''/'06 #0& +0 #&&+6+10
61 174 #22.+#0%' 9#44#06; 9' 5*#.. 4'2.#%' 6*' #22.+#0%' 70&'4 6*' (1..19+0) %10&+6+105
( &#/#)' +5 %#75'& $; 9#6'4 &7' 61 # /#.(70%6+10 1( 174 37#>612 5;56'/ 9'5*#..
/#-' )11& 6*' &#/#)' +0 6*' %#5' 1( 24+8#6' %1057/'45
*+5 .+#$+.+6; 9#44#06; +5 8#.+& (14 6*' 5'48+%' .+(' 1( 6*' #22.+#0%'
*' 9#44#06; %.#+/ +5 57$,'%6 61 %144'%6 +056#..#6+10 #0& %100'%6+10 1( 6*' #22.+#0%' +0
#%%14&#0%' 9+6* 174 +05647%6+105 <*+5 #.51 +0%.7&'5 %144'%6 +056#..#6+10 1( 6*' 37#>612
':6'05+10 14+)+0#. #%%'5514; 74 9#44#06; &1'5 016 %18'4 &'('%6+8' 5722.; .+0'5 14
(+66+0)5 72 61 6*' 37#>612 %100'%6+10 10 6*' 6#2
0 24+0%+2.' +6 +5 016 0'%'55#4; 61 /10+614 #0 #22.+#0%' (+66'& 9+6* 37#>612 &74+0)
12'4#6+10 14 61 5'%74' +6 #(6'49#4&5 $; 6740+0) 1(( 6*' 6#2 !17 5*17.& 10.; 6740 1(( 6*' 6#2
+( ;17 #4' #$5'06 (41/ *1/' (14 # 241.10)'& 2'4+1& ') 10 *1.+&#; (14 5'8'4#. 9''-5
+'/'05#75)'4=6'
+0 '57%*'0 +' 705 +/ 06'40'6
*6629995+'/'05&'*#75)'4#'6'
'0 "81..+
Download PDF