Autoriseret dansk forhandler
service@coffeetime.dk
www.coffeetime.dk | Bestil tilbehør online | Leveret indenfor 24 timer
The IMPRESSA X9 Win Manual
KE
Original instructions for use
Before using the machine read the instructions for use.
The ‘IMPRESSA Manual’ has been awarded the seal of approval by the
independent German Technical Inspection Agency, TÜV SÜD, due to its
easy-to-understand style, its thoroughness and coverage of safety
aspects.
JURA Type 657
Table of contents
Your IMPRESSA X9 Win
Control elements
4
6
Proper use
For your safety
6
The IMPRESSA X9 Win Manual
8
Symbol description.......................................................................................................................................8
1 IMPRESSA X9 Win
9
A stylish performance ..................................................................................................................................9
JURA on the Internet ....................................................................................................................................10
2 Preparing and using for the first time
11
Standard products........................................................................................................................................11
Setting up .......................................................................................................................................................11
Filling the water tank...................................................................................................................................12
Filling the bean container ...........................................................................................................................12
First-time use ................................................................................................................................................12
Inserting and activating the filter cartridge ............................................................................................14
Determining and adjusting the degree of water hardness ..................................................................14
Adjusting the grinder ..................................................................................................................................16
Switching on .................................................................................................................................................17
Switching off (standby) ...............................................................................................................................17
3 Familiarising yourself with the control options
18
Preparation at the touch of a button........................................................................................................18
Permanent settings in programming mode...........................................................................................19
Viewing information and maintenance status ......................................................................................20
Resetting the counter ..................................................................................................................................21
4 Preparation at the touch of a button
22
Espresso ........................................................................................................................................................22
Coffee ............................................................................................................................................................22
Cappuccino, milky coffee and latte macchiato......................................................................................23
Hot milk ........................................................................................................................................................23
Hot water ......................................................................................................................................................24
Steam ............................................................................................................................................................24
5 Permanent settings in programming mode
25
Product settings..........................................................................................................................................25
Time and weekday ......................................................................................................................................26
Timer .............................................................................................................................................................26
Automatic switch-off ..................................................................................................................................28
2
Table of contents
Language......................................................................................................................................................29
Format (unit of water amount and time format) ..................................................................................29
Switch-on rinse............................................................................................................................................30
Multimedia...................................................................................................................................................30
6 Maintenance
32
Maintenance tips.........................................................................................................................................32
Rinsing the machine...................................................................................................................................32
Dismantling and rinsing the dual spout .................................................................................................33
Milk system cleaning ..................................................................................................................................33
Coffee system cleaning ..............................................................................................................................34
Combined cleaning.....................................................................................................................................35
Changing the filter ......................................................................................................................................37
Descaling the machine...............................................................................................................................38
Cleaning the bean container.....................................................................................................................40
Descaling the water tank ...........................................................................................................................40
7 Display messages
42
8 Troubleshooting
44
9 Transport and environmentally neutral disposal
46
Transport / emptying the system ............................................................................................................46
Disposal.........................................................................................................................................................46
10 Technical data
47
Index
48
JURA contact details / Legal information
52
3
Control elements
Control elements
7
1
2
8
Open the cover
3
9
10
4
5
11
6
12
13
Figure: IMPRESSA X9 Win Platinum
1
2
3
4
5
6
4
Bean container with cover
Cup tray
Power switch and power cable (back of
machine)
Dual spout (height adjustable)
Milk pipes
Coffee grounds container
7
8
9
10
11
12
13
Filler funnel for cleaning tablet
Cover for programming buttons
Water tank with cover
Hot water pipe (pivoting)
Steam pipe (pivoting)
Cup platform
Drip tray
Control elements
1
2
3
4
Front left
Front right
1
2
3
Display
Product buttons (standard products):
1espresso button
1coffee button
2 coffee button
Milk foam button
Cappuccino button
Latte macchiato button
Milk coffee button
Milk button
(The products are shown on the display.)
4
5
5
Programming buttons:
Q On/off button
$
Filter button
$
Descaling button
9 Counter button
O P button
+
+ button
c Rinse button
6 Milk system cleaning button
7 Coffee system cleaning button
8 Combined cleaning button
0 Exit button
- button
m Hot water button
n Steam button
5
Important notes
Proper use
The machine is designed and intended for commercial use. It should
only be used to prepare coffee and to heat milk and water. Use for
any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of
improper use.
Before using the machine always carefully read and comply with
these instructions. Keep this manual close to the IMPRESSA and pass
it on to the next user if applicable.
The IMPRESSA may only be operated by instructed persons.
For your safety
Always read the following safety instructions carefully.
To prevent potentially fatal electric shocks:
Z Never use a machine which has been damaged or has a defective power cable.
Z For information on what to do in case of damage, for example
if there is a smell of burning, unplug the machine immediately
from the mains supply and contact the JURA service centre.
Z If the power cable for this machine is damaged, it must be
repaired either directly by JURA or by a JURA authorised service centre.
Z Make sure that the IMPRESSA and the power cable are not
located close to hot surfaces.
Z Ensure that the power cable is not trapped in any way and
does not rub against sharp edges.
Z Never open and repair the machine yourself. Do not modify
the machine in any way that is not described in the IMPRESSA
Manual. The machine contains live parts. If opened, there is a
danger of serious injury. Repairs may only be carried out by
authorised JURA service centres, using original spare parts
and accessories.
It is possible to scald or burn oneself on the spouts, on the hot water
pipe and steam pipe:
Z Place the machine out of the reach of children.
Z Do not touch any hot parts. Use the handles provided.
6
Important notes
A defective machine is not safe and could cause injury or fire. To
avoid damage and any associated risk of injury or fire:
Z Never allow the power cable to trail, as someone could trip
over the power cable and/or it could get damaged.
Z Protect your IMPRESSA from environmental influences such
as rain, frost and direct sunlight.
Z Do not put the IMPRESSA, cable or connections in water.
Z Never put the IMPRESSA or its components into the dishwasher.
Z Turn your IMPRESSA off at the power switch before cleaning
the machine. Always wipe your IMPRESSA with a damp cloth
rather than a wet one, and protect it from prolonged water
splash.
Z Do not set up the IMPRESSA anywhere where a jet of water
may be used.
Z Only connect the machine to a power supply in accordance
with the information on the rating plate. The rating plate is
located on the rear of your IMPRESSA. Further technical data
is given in Chapter 10 ‘Technical Data’.
Z Use only original JURA care products. Use of accessories that
are not explicitly recommended by JURA could damage the
IMPRESSA.
Z Do not use any coffee beans treated with additives or caramelised coffee beans.
Z Only fill the water tank with fresh, cold water.
Z Switch the machine off at the power switch if you are absent
for long periods of time.
Using the CLARIS filter cartridge safely:
Z Keep the filter cartridges out of the reach of children.
Z Store the filter cartridges in a dry place in the sealed
package.
Z Protect the filter cartridges from heat and direct sunlight.
Z Never use any damaged filter cartridges.
Z Never open filter cartridges.
7
The IMPRESSA X9 Win Manual
The IMPRESSA X9 Win Manual
You are holding the manual for your IMPRESSA X9 Win in your hand.
It will help you to familiarize yourself with your IMPRESSA safely and
quickly and teach you the full range of facilities it offers.
Chapter 2, ‘Preparing and using for the first time’, explains step-bystep how to set up and prepare the IMPRESSA.
Chapter 3, ‘Familiarising yourself with the control options’ is important for you to read as you are familiarising yourself with your
IMPRESSA. It invites you to actively explore all the different coffee
experiences that it offers.
All the other chapters are intended to help you when you have a
specific query.
If you use the IMPRESSA X9 Win, you will become a master at
preparing exciting coffee specialities, you will be a Barista!
You can download the short operating instructions for your machine
from the JURA website (www.jura.com).
Symbol description
Warnings
Always take note of any information marked with the CAUTION or WARNING symbol.
The signal word WARNING points out potential risk of serious injury, and the signal
CAUTION word CAUTION potential risk of slight injury.
CAUTION
The CAUTION symbol is used to draw attention to circumstances which could cause
the machine to become damaged.
Symbols used
8
E
Information and tips to make things easier for you as you use your IMPRESSA.
@
References to the online JURA website, where you can find interesting further information: www.jura.com.
T
Prompt to take action. This symbol means that you are being prompted to perform
some action.
1IMPRESSA X9 Win
1 IMPRESSA X9 Win
A stylish performance
With its elegant design and highest-quality materials, this luxury
machine with its cool Nordic style not only has an appealing exterior, but easily fulfils the most sophisticated coffee wishes of customers, guests and colleagues. In addition to such classic specialities
such as ristretto, espresso and coffee, the IMPRESSA X9 Win also
makes contemporary drinks such as cappuccino or latte macchiato
at the touch of a button.
In addition to its unique design and the variety of product options,
the TFT screen also permits adScreen advertising. This is useful at
the POS where eight of ten purchasing decisions are made, or in
seminar centres, where attendees can be informed about additional
offers. You too can give your customers that decisive impetus, and
motivate your target group to make spontaneous extra purchases.
The IMPRESSA X9 Win is tremendous for all kinds of applications!
Z
Z
Simple operation with ‘Smart Lead’: ‘Smart Lead’, the interactive JURA user guidance with visual and audio features,
guides personnel through all operating and care steps. This
makes maintenance simple and prevents incorrect intervention. From filling of the water tank through to cleaning –
‘Smart Lead’ demonstrates each step with visual and audio
output. The user is guided through the complete procedure,
which simplifies the process and minimises errors. This prevents unnecessary service costs and loss of turnover caused
by machine errors.
Coffee specialities: The IMPRESSA X9 Win makes more than
20 coffee specialities, all of which can be adapted to suit your
own personal preferences. The 3.5 inch TFT display guides you
through to the required coffee speciality and offers you coffee
enjoyment at the touch of a button. With ristretto, espresso,
regular coffee, milky coffee, coffee in a glass, cappuccino or a
trendy latte macchiato: Let your taste make the decision! Up
to 100 cups can be prepared each day with ease.
9
1IMPRESSA X9 Win
Z
Z
JURA on the Internet
Programming: When the chrome-plated programming cover
elegantly slides upwards, it reveals the programming panel
with the various setting options. The cleaning, rinsing and
descaling programmes are also started from here, and the
integrated cup counter can also be activated. Would you like
to restrict the programming options to a specific group of
users? No problem: Simply generate code groups.
Customisable: The setting options of the IMPRESSA X9 Win
are just as varied as the wishes of our customers. The machine
can therefore be equipped with a number of different accessories. These include a permanent water connection, a wide
range of vending systems, a matching cup warmer or a refrigerator for the milk. Request our full-range brochure and contact an authorised dealer for advice.
Visit us on the Internet.
@ At www.jura.com you will find interesting and up-to-date
information on your IMPRESSA and on every aspect of
coffee.
10
2 Preparing and using for the first time
2 Preparing and using for the first time
This chapter provides you with the information you need to use your
IMPRESSA without any problems. You will prepare your IMPRESSA
step-by-step for your first coffee experience.
Standard products
Your
ard:
Z
Z
Z
Z
Z
Z
Z
Z
IMPRESSA is supplied with the following products as stand1espresso
1coffee
2 coffees
Milk foam
Cappuccino
Latte macchiato
Milky coffee
Milk
Settings by the JURA service
technician
The following settings can only be made by the JURA service technician:
Z Customised product programming. The standard products
can be replaced by:
U 2 espressi, 1ristretto, 2 ristretti, small pot, macchiato, milky
coffee, hot water, steam, 2x
U Grinder selection or rinse button (all buttons can be
arranged to preference)
Z Blocking products
Z Setting the filter capacity
Z Assigning code groups: Three code groups can be assigned.
The respective code groups correspond to different authorisations. It can be defined, for example, that the programming
mode of the maintenance programmes is blocked by a code.
Setting up
When setting up your IMPRESSA, please note the following:
Z Place the IMPRESSA on a horizontal surface that is not sensitive to water.
Z Choose a spot for your IMPRESSA which is protected against
overheating. Ensure that the ventilation slots are not covered.
11
2 Preparing and using for the first time
Filling the water tank
CAUTION
To enjoy perfect coffee, we recommend changing the water every
day.
Milk, mineral water or other liquids can damage the water tank or
the machine.
T Only fill the water tank with fresh, cold water.
T Remove the cover of the water tank.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert. It must
snap firmly into place.
T Replace the cover on the water tank.
E You can also fill the water tank without removing it. To this
purpose remove the cover of the water tank and use a receptacle to fill the water tank from above with fresh, cold water.
Filling the bean container
CAUTION
Your IMPRESSA features two bean containers. You therefore have
the option of using two types of coffee beans. The cover of the bean
container also acts as an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
Coffee beans which have been treated with additives (e.g. sugar),
pre-ground or freeze-dried coffee will damage the grinder.
T Only use untreated coffee beans to refill the bean container.
T Remove the cover of the bean container.
T Remove any dirt or foreign objects inside the bean container.
T Fill the bean container with coffee beans.
T Replace the cover on the bean container.
First-time use
WARNING
If the machine is operated with a defective power cable, there is a
danger of electric shock.
T Never use a machine which has a defective power cable.
Precondition: The water tank and bean container are full.
T Insert the mains plug into a power socket.
12
2 Preparing and using for the first time
3 T Switch on the IMPRESSA using the power switch on the back
of the machine.
T Open the cover of the programming buttons.
Q T Press the on/off button to switch the IMPRESSA on.
SPRACHE DEUTSCH appears on the display.
T Press the + or - button several times until the desired language is displayed. For Example: LANGUAGE ENGLISH
O T Press the P button to confirm the language.
CONFIRMED appears briefly on the display to confirm the
setting.
E You have now set the language of the machine. The language of the film clips can be set in programming mode with
the MULTIMEDIA LANGUAGE option.
O
O
O
c
TIME HOURS --:-T Press the + or - button several times to set the hours.
TIME HOURS 12:00 (Example)
T Press the P button to confirm the hour setting.
TIME MINUTES 12:00 (Example)
T Press the + or - button to set the minutes.
TIME MINUTES 12:45 (Example)
T Press the P button to confirm the minute setting.
CONFIRMED appears briefly on the display.
WEEKDAY MONDAY
T Press the + or - button several times to set the weekday.
WEEKDAY WEDNESDAY (Example)
T Press the P button to confirm the weekday setting.
CONFIRMED and WELCOME TO JURA appear briefly on the
display. PRESS RINSE BUTTON is then displayed.
T Press the rinse button.
SYSTEM FILLS, the system isfilled with water. Asmall amount
of water flows from the hot water spout. The operation stops
automatically. After heating, PRESS RINSE BUTTON is displayed.
13
2 Preparing and using for the first time
c T Press the rinse button to start the rinse operation.
MACHINEISRINSING, water flows out of the dual spout. The
operation stops automatically. Your IMPRESSA is ready for
operation.
E After first-time use do not disconnect the IMPRESSA from the
power supply for 24 hours to ensure that it is in the optimum
operating condition.
E When a coffee speciality has been prepared for the first time,
it is possible that FILL BEANS is shown on the display as the
grinder has not yet been completely filled with coffee beans.
In this case prepare a different coffee speciality.
E If you have not been able to use the machine for the first time
correctly and fully, contact your JURA service partner. The contact details are given in the ‘JURA contacts’ section on the last
page of these instructions.
Inserting and activating the filter cartridge
Your IMPRESSA no longer has to be descaled if you are using the
CLARIS filter cartridge.
E The CLARIS filter cartridge must be installed for the first time
by a service technician. Please contact your JURA service partner.
Determining and
adjusting the degree of
water hardness
Water is heated in the IMPRESSA. This results in a build-up of limescale over time. The harder the water, the more frequently the
machine needs to be descaled. For this reason it is important to
select the correct setting on the IMPRESSA for the water hardness of
the used water.
The water hardness can be adjusted on a continuous scale between
1° dH and 30° dH. This can also be deactivated, which means that
the IMPRESSA will not let you know when it has to be descaled.
E However, if you are using the CLARIS filter cartridge and it is
activated, you will not be able to adjust the water hardness.
14
2 Preparing and using for the first time
Determining the water
hardness
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
T Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
T Wait for about one minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
You can now adjust the water hardness.
Adjusting the water
hardness
Example: To change the water hardness from 16° dH to 25° dH, proceed as follows:
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATER HARDNESS 16° dH
appears.
O T Press the P button to enter the programme item.
WATERHARDNESS 16° dH
T Press the + button several times to select the water hardness.
WATERHARDNESS 25° dH (example)
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
WATERHARDNESS 25° dH
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
15
2 Preparing and using for the first time
Adjusting the grinder
CAUTION
Both grinders can be adjusted on a continuous scale to suit the roast
of the respective coffee blend.
If you adjust the fineness of grind when the grinder is not in operation, the setting ring could be damaged.
T Only adjust the fineness of grind when the grinder is
running.
The fineness of grind setting is correct if the coffee flows regularly
from the coffee spout. In addition, a fine, dense crema is formed.
Our recommendations:
Z Select a fine setting for a light roast.
U If the fineness of grind is too fine, the coffee only drips from
the coffee spout.
Z
Select a coarse setting for a darker roast.
U If the fineness of grind is too coarse, the coffee flows too
quickly from the coffee spout.
Example: To change the fineness of grind during coffee preparation,
proceed as follows:
Precondition: Your IMPRESSA is ready for operation.
T Place a cup under the dual spout.
T Press the 1coffee button.
The grinder starts and 1COFFEE is displayed.
T Set the setting ring on the bean container to the required
position while the grinder is running.
The coffee will be prepared and the fineness of grind is
adjusted.
16
2 Preparing and using for the first time
Switching on
When the IMPRESSA is switched on, a prompt for the rinse operation
automatically appears which is initiated by pressing the rinse button.
This setting can be changed in programming mode so that the
machine automatically activates the switch-on rinse (see Chapter 5
‘Permanent settings in programming mode – Switch-on rinse’).
Precondition: Your IMPRESSA is switched on at the power switch.
T Open the cover of the programming buttons.
Q T Press the on/off button to switch the IMPRESSA on.
WELCOME TO JURA appears briefly on the display. After
heating, PRESS RINSE BUTTON is displayed.
c T Press the rinse button to start the rinse operation.
MACHINEISRINSING, water flows out of the dual spout. The
operation stops automatically. Your IMPRESSA is ready for
operation.
Switching off (standby)
When you switch your IMPRESSA off, the spouts with which a coffee
speciality or milk have been prepared are rinsed. If only hot water or
steam was prepared, the machine switches off without rinsing.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
Q T Press the on/off button to switch the IMPRESSA off.
GOODBYE appears on the display. The machine is rinsed,
water flows out of the dual spout. The operation stops automatically, the IMPRESSA is switched off (standby).
E To disconnect the machine completely from the mains, switch
it off with the power switch on the rear of the machine.
17
3 Familiarising yourself with the control options
3 Familiarising yourself with the control options
With the IMPRESSA, you can prepare an excellent coffee or milk speciality at the touch of a button. You also have the option of adjusting
the coffee strength and temperature, as well as the amount of water
to your personal taste.
Thischapter will allow you to become familiar with all control options
with the aid of examples. To familiarise yourself with your IMPRESSA,
we recommend that you make a point of actively trying the facilities
described in this chapter. You will find this is well worthwhile.
Learn how to perform the following:
Z Preparation at the touch of a button
Z Permanent settings in programming mode
E You can stop the machine at any time while a coffee or milk
speciality or hot water is being prepared. To do this, press any
button.
Preparation at the
touch of a button
Prepare your favourite coffee speciality at the touch of a button.
Preparing a coffee speciality
at the touch of a button
Example: This is how to prepare one coffee.
Precondition: Your IMPRESSA is ready for operation.
T Place a cup under the dual spout.
T Press the 1coffee button.
Coffee preparation then begins. You can follow the current
status of preparation on the progress bar. The pre-set
amount of water flows into the cup. The operation stops
automatically.
Your IMPRESSA is once more ready for operation.
18
All coffee specialities are prepared following this model.
3 Familiarising yourself with the control options
Permanent settings in
programming mode
Programme item
You can easily adjust your IMPRESSA to your personal coffee blends
and specialities. The permanent setting options in programming
mode are shown here:
Subitem
Explanation
NOT ACTIVE,
WATERHARDNESS
1° dH – 30° dH
(is only displayed when
the filter is not activated)
T Adjust the water hardness.
PRODUCT SETTINGS
T Select your settings for the coffee
and milk specialities as well as hot
water and steam.
TIME
--:--, WEEKDAY
T Set the time and weekday.
T Set the switch-on and switch-off
times and specify the weekdays on
which IMPRESSA should switch on
and off automatically.
TIMER
OFF AFTER
OFF AFTER--. HRS,
0.5 HRS – 9 HRS
T Set the number of hours after
which the IMPRESSA should switch
off automatically.
SWITCH-ON RINSE
MANUAL, AUTOMATIC
T Set whether the switch-on rinse
should be started manually or
automatically.
LANGUAGE
DEUTSCH, FRANCAIS, ENGLISH,
ITALIANO, NL
T Select your language.
FORMAT
UNIT,
TIME FORMAT
T Select the unit of the amount of
water and the time format.
T Keep track of all prepared coffee
and milk specialities and view the
maintenance status.
INFORMATION
MULTIMEDIA
VOLUME, BRIGHTNESS,
CONTRAST,
MULTIMEDIA LANGUAGE,
VIDEO PLAYBACK
(INTAKE, ALERT, INSTRUCTION),
VIDEO SOUND
(INTAKE, ALERT, INSTRUCTION)
T Select your settings for the
display and the explanatory film
clips.
19
3 Familiarising yourself with the control options
Settings in programming mode always follow the same model.
Example: Proceed as follows to change the amount of powder for
an espresso.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATER HARDNESS 16° dH
appears.
T Press the + or - button several times until PRODUCT
SETTINGS is shown.
O T Press the P button to enter the programme item.
SELECT PRODUCT and the available products are displayed.
T Press the 1espresso button.
1ESPRESSO / WATERAMOUNT 35 ML
T Press the + button several times until 1ESPRESSO / POWDER
AMOUNT is shown.
O T Press the P button to enter the programme item.
1ESPRESSO / POWDERAMOUNT
T Press the + or - button several times to select the powder
amount.
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
1ESPRESSO / POWDERAMOUNT
0 T Press the exit button to exit the programming item.
SELECT PRODUCT
0 T Press the exit button to exit the programming item.
PRODUCT SETTINGS
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Viewing information
and maintenance
status
20
With the INFORMATION programme item you can view the following information:
Z Number of the prepared coffee and milk specialities and hot
water
Z Maintenance statusand number of maintenance programmes
performed (cleaning, descaling, filter change, milk system
cleaning)
3 Familiarising yourself with the control options
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until INFORMATION is
shown.
O T Press the P button to enter the programme item.
TOTAL and the overall number of preparations are displayed.
E Press the + or - button several times to view the various items
of information.
0 T Press the exit button to exit the programming item.
INFORMATION
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Resetting the counter
With the individual counter (counter button 9) you can track your
consumption over a specific period of time which you can specify.
This counter can be reset to zero at any time.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
9 T Press the counter button until an acoustic signal is given.
1COFFEE and the number of preparations are displayed.
E Press the + or - button several times to view the respective
number of prepared products.
0 T Press the exit button.
COUNTERDELETE / NO
T Press the + or - button to change the setting to YES.
O T Press the P button to reset the counter.
DELETED appears briefly on the display.
Your IMPRESSA is once more ready for operation.
21
4 Preparation at the touch of a button
4 Preparation at the touch of a button
In this chapter you will find out how to prepare coffee and milk specialities as well as hot water and steam without making further settings.
Chapter 3, ‘Familiarising yourself with the control options’, will teach
you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 5, ‘Permanent settings in programming mode’.
E You can stop the machine at any time while a coffee or milk
speciality or hot water is being prepared. To do this, press any
button.
Espresso
The classic coffee drink from Italy. An espresso is crowned by a fine,
dense crema on the surface.
Example: This is how to prepare one espresso.
Precondition: Your IMPRESSA is ready for operation.
T Place an espresso cup under the dual spout.
T Press the 1espresso button.
Coffee preparation then begins. You can follow the current
status of preparation on the progress bar. The pre-set
amount of water flows into the cup. The operation stops
automatically.
Your IMPRESSA is once more ready for operation.
Coffee
Example: This is how to prepare one coffee.
Precondition: Your IMPRESSA is ready for operation.
T Place a cup under the dual spout.
T Press the 1coffee button.
Coffee preparation then begins. You can follow the current
status of preparation on the progress bar. The pre-set
amount of water flows into the cup. The operation stops
automatically.
Your IMPRESSA is once more ready for operation.
E To prepare two coffees, place two cups under the dual spout
and press the 2 coffees button.
22
4 Preparation at the touch of a button
Cappuccino,
milky coffee and
latte macchiato
You can prepare cappuccino, milky coffee and latte macchiato very
simply at the touch of a button.
Example: This is how to prepare one latte macchiato.
Precondition: Your IMPRESSA is ready for operation.
T Immerse both milk pipes completely in the milk.
T Place a glass under the dual spout.
T Press the latte macchiato button.
Preparation starts and the milk foam flows into the glass.
You can follow the current status of preparation on the
progress bar.
A short interval follows. The pre-set amount of water of the
espresso flows into the glass.
The operation stops automatically.
Your IMPRESSA is once more ready for operation.
E Ten minutes after milk is prepared, the dual spout is automatically rinsed. This rinsing operation is announced by an acoustic signal. The setting can be changed by a JURA service technician.
Hot milk
You can prepare hot milk very simply at the touch of a button.
Precondition: Your IMPRESSA is ready for operation.
T Immerse both milk pipes completely in the milk.
T Place a cup under the dual spout.
T Press the milk button.
Preparation starts and the hot milk flows into the cup. You
can follow the current status of preparation on the progress
bar.
The operation stops automatically.
Your IMPRESSA is once more ready for operation.
E Ten minutes after milk is prepared, the dual spout is automatically rinsed. This rinsing operation is announced by an acoustic signal. The setting can be changed by a JURA service technician.
23
4 Preparation at the touch of a button
Hot water
CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Precondition: Your IMPRESSA is ready for operation.
T Place a cup under the hot water pipe.
m T Press the hot water button.
Preparation then begins. You can follow the current status of
preparation on the progress bar.
The operation stops automatically when the pre-set amount
of water is reached.
Your IMPRESSA is once more ready for operation.
Steam
CAUTION
There is a danger of scalding from hot steam.
T Avoid direct contact with the skin.
Precondition: Your IMPRESSA is ready for operation.
T Place a receptacle under the steam pipe.
n T Press the steam button.
Preparation then begins. You can follow the current status of
preparation on the progress bar.
The operation stops automatically when the pre-set amount
of steam is reached.
Your IMPRESSA is once more ready for operation.
24
5 Permanent settings in programming mode
5 Permanent settings in programming mode
Product settings
With the PRODUCT SETTINGSprogramme item you can select individual settings for all coffee and milk specialities as well as hot
water.
The following permanent settings can be made:
Product
Amount
Additional setting options
1espresso,
1coffee,
2 coffees
WATERAMOUNT: 25 ML – 300 ML
(with 2 coffees: amount per cup)
POWDERAMOUNT
GRINDER(left and right grinder
in percent)
TEMPERATURE: LOW, NORMAL,
HIGH
Cappuccino, milky
coffee, latte macchiato
WATERAMOUNT: 25 ML – 300 ML
POWDERAMOUNT
MILK AMOUNT: 0 / 3 SEC – 120 SEC
MILK FOAM: 0 / 3 SEC – 120 SEC
GRINDER(left and right grinder
in percent)
TEMPERATURE: LOW, NORMAL,
HIGH
Hot milk
MILK AMOUNT: 0 / 3 SEC – 120 SEC
–
Hot water (portion)
WATERAMOUNT: 25 ML – 500 ML
–
Steam (permanent)
–
–
Settings in programming mode always follow the same model.
Example: Proceed as follows to change the powder amount for
1espresso.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until PRODUCT
SETTINGS is shown.
O T Press the P button to enter the programme item.
SELECT PRODUCT
T Press the 1espresso button.
1ESPRESSO / WATERAMOUNT
T Press the + button several times until 1ESPRESSO / POWDER
AMOUNT is shown.
O T Press the P button to enter the programme item.
POWDERAMOUNT
25
5 Permanent settings in programming mode
O
0
0
0
Time and weekday
T Press the + or - button several times to select the amount of
powder.
T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
1ESPRESSO / POWDERAMOUNT
T Press the exit button to exit the programming item.
SELECT PRODUCT
T Press the exit button to exit the programming item.
PRODUCT SETTINGS
T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
You already set the time and weekday when you used the machine
for the first time. You can change this setting.
Example: How to change the time from 8:45 (example) to 9:50.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATER HARDNESS 16° dH
appears.
T Press the + or - button several times until TIME is shown.
O T Press the P button to enter the programme item.
TIME HOURS 08:45 (Example)
T Press the + or - button several times to set the hours.
O T Press the P button to confirm the setting.
T Press the + or - button to set the minutes.
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
WEEKDAY MONDAY (Example)
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
TIME
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Timer
26
The following settings can be made in the TIMERmenu item:
Z MACHINE ON
U Set the required switch-on time.
5 Permanent settings in programming mode
Z
Z
MACHINE OFF
U Set the required switch-off time.
ON/OFF
U Set the weekdays on which the IMPRESSA should switch on
and off automatically.
E The programmable switch-on and switch-off time can only be
set when the time has been set.
E The programmable switch-on only works when the machine
is switched on at the power switch (standby).
Example: Proceed as follows to set the switch-on time to 07:30 and
stipulate that your IMPRESSA does not switch on automatically on
Sundays.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATER HARDNESS 16° dH
appears.
T Press the + or - button several times until TIMERis shown.
O T Press the P button to enter the programme item.
MACHINE ON --:-O T Press the P button to enter the programme item.
MACHINE ON / HOURS --:-T Press the + button several times until MACHINEON / HOURS
07:00 is shown.
O T Press the P button to confirm the hour setting.
T Press the + button several times until MACHINE ON /
MINUTES 07:30 is shown.
O T Press the P button to confirm the minute setting.
CONFIRMED appears briefly on the display.
MACHINE ON 07:30
T Press the + or - button several times until ON/OFF / SUNDAY
YES is displayed.
O T Press the P button to enter the programme item.
ON/OFF / SUNDAY YES
T Press the + or - button to change the setting to SUNDAY
NO.
27
5 Permanent settings in programming mode
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
ON/OFF / SUNDAY NO
0 T Press the exit button to exit the programming item.
TIMER
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the last action on
the machine.
E The programmable switch-off time can be adjusted between
0.5 and 9 hours or deactivated.
Example: Proceed as follows to change the automatic switch-off
time from 5.0 HRS TO 2.0 HRS.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until OFF AFTER5 HRS
is shown.
O T Press the P button to enter the programme item.
OFF AFTER5.0 HRS
T Press the - button several times until OFF AFTER 2.0 HRS is
shown.
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
OFF AFTER2.0 HRS
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
28
5 Permanent settings in programming mode
Language
You selected the language when the machine was used for the first
time. You can change this setting.
Example: To change the language from ENGLISH to DEUTSCH, proceed as follows.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until LANGUAGE
ENGLISH is shown.
O T Press the P button to enter the programme item.
LANGUAGE ENGLISH
T Press the + or - button several times to select the language,
for example SPRACHE DEUTSCH.
O T Press the P button to confirm the setting.
GESPEICHERT appears briefly on the display.
SPRACHE DEUTSCH
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Format (unit of water
amount and time
format)
You can change the unit of the amount of water from ‘ml’ to ‘oz’ and
the time format to ‘24 HRS’ or ‘AM/PM’ in the FORMAT programme
item.
Example: To change the unit for the amount of water from ML to
OZ, proceed as follows.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until FORMAT is
shown.
O T Press the P button to enter the programme item.
FORMAT / UNIT ML
O T Press the P button to enter the programme item.
FORMAT / UNIT ML
T Press the + or - button to change the setting to UNIT OZ.
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
FORMAT / UNIT OZ
29
5 Permanent settings in programming mode
0 T Press the exit button to exit the programming item.
FORMAT
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Switch-on rinse
You can set whether the switch-on rinse must be started manually
or automatically.
Example: To programme the machine for a manual switch-on rinse,
proceed as follows.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until SWITCH-ON
RINSE / AUTOMATIC is shown.
O T Press the P button to enter the programme item.
SWITCH-ON RINSE / AUTOMATIC
T Press the + or - button to change the setting to MANUAL.
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
SWITCH-ON RINSE / MANUAL
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
Multimedia
30
The following settings can be made in the MULTIMEDIA programme
item:
Z VOLUME
Z BRIGHTNESS
Z CONTRAST
Z MULTIMEDIA LANGUAGE
Z VIDEO PLAYBACK - INTAKE
U Film clips during preparation of a product
Z VIDEO PLAYBACK - ALERT
U Film clips when your IMPRESSA prompts an action, for
example filling the bean container or water tank
Z VIDEO PLAYBACK - INSTRUCTION
U Explanatory film clips when you have started a maintenance
programme
5 Permanent settings in programming mode
Z
Z
Z
VIDEO SOUND - INTAKE
VIDEO SOUND - ALERT
VIDEO SOUND - INSTRUCTION
E In the VIDEO PLAYBACKand VIDEO SOUND programme items,
the options CONTINUOUS, NEVERand ONCEare available for
playback.
Example: Proceed as follows to programme playback of the sound
(VIDEO SOUND) once in the event of an ALERT.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
O T Press the P button until WATERHARDNESS appears.
T Press the + or - button several times until MULTIMEDIA is
shown.
O T Press the P button to enter the programme item.
MULTIMEDIA / VOLUME
T Press the + or - button several times until VIDEO SOUND ALERT is shown.
O T Press the P button to enter the programme item.
CONTINUOUS
T Press the + or - button several times until VIDEO SOUND ALERT / ONCE is shown.
O T Press the P button to confirm the setting.
CONFIRMED appears briefly on the display.
VIDEO SOUND - ALERT
0 T Press the exit button to exit the programming item.
MULTIMEDIA
0 T Press the exit button to exit programming mode.
Your IMPRESSA is once more ready for operation.
31
6 Maintenance
6 Maintenance
Maintenance tips
To ensure that you get many years of reliable service out of your
IMPRESSAand to guarantee an optimum coffee quality, the machine
requires daily maintenance. Proceed as follows:
Z Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
Z Rinse the water tank with clean water.
Z Dismantle and rinse the dual spout (See Chapter 6 ‘Maintenance – Dismantling and rinsing the dual spout’).
Z Wipe the surface of the machine with a damp cloth.
Rinsing the machine
When the IMPRESSA is switched on, a prompt to perform a rinse
operation appears after heating, or this is automatically started.
When the IMPRESSA is switched off, a rinse operation is automatically initiated.
In programming mode you can make a setting to stipulate whether
the switch-on rinse needs to be activated manually or whether it is
activated automatically (see Chapter 5 ‘Permanent settings in programming mode – Switch-on rinse’).
Rinsing the machine –
manually
Rinsing can be initiated manually at any time.
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
c T Press the rinse button.
MACHINE IS RINSING, water flows out of the dual spout.
The operation stops automatically.
Your IMPRESSA is once more ready for operation.
32
6 Maintenance
Dismantling and
rinsing the dual spout
For reasons of hygiene and to ensure that the dual spout works perfectly, it must be regularly dismantled and rinsed.
Precondition: Your IMPRESSA is switched off (standby).
T Press the release button on the top of the dual spout and
remove the cover.
T Carefully pull the pipes out.
T Remove the spouts and dismantle all components.
T Rinse all parts thoroughly with hot water.
T Reassemble the individual parts. Pay attention to the colour
of the individual parts.
T Mount the spouts on the machine.
T Replace the cover.
Milk system cleaning
CAUTION
For reasons of hygiene and to ensure that the dual spout works perfectly, you should clean the milk system daily if you have prepared
milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Only use original JURA care products.
E The cleaning programme only lasts about 2 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E The JURA Cappuccino Cleaner is available from stockists.
33
6 Maintenance
Precondition: Your IMPRESSA is ready for operation.
T Open the cover of the programming buttons.
6 T Press the milk system cleaning button.
The current maintenance status is shown.
6 T Press the milk system cleaning button again.
START MILK SYSTEM CLEANING
6 T Press the milk system cleaning button to start the cleaning
operation.
CLEANERFORMILK SYSTEM CLEANING
T Fill a receptacle with 400 ml water and add 11/2 caps of the
JURA Cappuccino Cleaner.
T Immerse both milk pipes completely in the cleaning solution.
T Place a receptacle (at least 500 ml) under the dual spout.
6 T Press the milk system cleaning button.
MACHINE IS CLEANING, the dual spout and the pipes are
cleaned.
The procedure is interrupted, WATER FOR MILK SYSTEM
CLEANING.
T Rinse the receptacle thoroughly, fill it with approx. 400 ml of
fresh water and immerse the milk pipes in the water.
T Empty the other receptacle and place it under the dual spout
once more.
6 T Press the milk system cleaning button.
MACHINE IS CLEANING, the dual spout and the pipes are
cleaned with fresh water.
The operation stops automatically.
Your IMPRESSA is once more ready for operation.
Coffee system cleaning
After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean the coffee system.
CAUTION
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Only use original JURA care products.
E The cleaning programme only lasts about 20 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
34
6 Maintenance
E JURA cleaning tablets are available from stockists.
Precondition: Your IMPRESSA is ready for operation, the message
R is shown on the display.
T Open the cover of the programming buttons.
7 T Press the coffee system cleaning button.
The current maintenance status is shown.
7 T Press the coffee system cleaning button again.
START COFFEE SYSTEM CLEANING
7 T Press the coffee system cleaning button to start the cleaning
operation.
EMPTY DRIP TRAY
T Empty the drip tray.
EMPTY COFFEE GROUNDS CONT.
T Empty the coffee grounds container.
T Replace the coffee grounds container and the drip tray.
PRESS BUTTON
O T Press the P button.
MACHINE IS CLEANING, water flows out of the dual spout.
You can follow the current cleaning status of the coffee system on the progress bar.
The operation is interrupted, ADD TABLET.
T Insert a JURA cleaning tablet into the filler funnel for the
cleaning tablet.
7 T Press the coffee system cleaning button.
MACHINE IS CLEANING, water flows out of the dual spout
several times.
The process is interrupted, EMPTY DRIP TRAY.
T Empty the drip tray.
EMPTY COFFEE GROUNDS CONT.
T Empty the coffee grounds container.
T Replace the coffee grounds container and the drip tray.
Your IMPRESSA is once more ready for operation.
Combined cleaning
During combined cleaning, both the milk and coffee systems are
cleaned. After 220 coffee preparations or 80 switch-on rinses, the
IMPRESSA will prompt you to clean the coffee system. You have the
option of cleaning the milk system in addition to the coffee system.
35
6 Maintenance
CAUTION
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Only use original JURA care products.
E The cleaning programme only lasts about 22 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets and the JURA Cappuccino Cleaner are
available from stockists.
Precondition: Your IMPRESSA is ready for operation, the message
R is shown on the display.
T Open the cover of the programming buttons.
8 T Press the combined cleaning button.
The current maintenance status is shown.
8 T Press the combined cleaning button again.
START COMBINED CLEANING
8 T Press the combined cleaning button to start the cleaning
operation.
EMPTY DRIP TRAY
T Empty the drip tray.
EMPTY COFFEE GROUNDS CONT.
T Empty the coffee grounds container.
T Replace the coffee grounds container and the drip tray.
CLEANERFORMILK SYSTEM CLEANING
T Fill a receptacle with 400 ml water and add 11/2 caps of the
JURA Cappuccino Cleaner.
T Immerse both milk pipes completely in the cleaning solution.
T Place a receptacle (at least 500 ml) under the dual spout.
6 T Press the milk system cleaning button.
MACHINEISCLEANING. You can follow the current status of
combined cleaning on the progress bar.
The operation is interrupted, ADD TABLET.
36
6 Maintenance
T Insert a JURA cleaning tablet into the filler funnel for the
cleaning tablet.
8 T Press the coffee system cleaning button.
MACHINE IS CLEANING, water flows out of the dual spout
several times. The dual spout and the pipes are cleaned.
The procedure is interrupted, WATER FOR MILK SYSTEM
CLEANING.
T Rinse the receptacle thoroughly, fill it with approx. 400 ml of
fresh water and immerse the milk pipes in the water.
T Empty the other receptacle and place it under the dual spout
once more.
6 T Press the milk system cleaning button.
MACHINE IS CLEANING, the dual spout and the pipes are
cleaned with fresh water.
The process is interrupted, EMPTY DRIP TRAY.
T Empty the drip tray.
EMPTY COFFEE GROUNDS CONT.
T Empty the coffee grounds container.
T Replace the coffee grounds container and the drip tray.
Your IMPRESSA is once more ready for operation.
Changing the filter
After 50 litres of water have flowed through, or after two months,
the filter will cease to work. Your IMPRESSA will automatically
prompt you to change the filter.
E The filter button is only active if the amount of water of the
filter is set to 50 l. If another water amount is set, the filter can
only be replaced by a JURA service technician.
Precondition: Your IMPRESSA is ready for operation, the message
R is shown on the display.
T Open the cover of the programming buttons.
$ T Press the filter button.
The current maintenance status is shown.
$ T Press the filter button again.
START CHANGE FILTER
$ T Press the filter button.
INSERT FILTER
T Remove the water tank and empty it.
37
6 Maintenance
T Take out the old CLARIS plus filter cartridge and the extension.
T Fit the extension onto a new filter cartridge.
T Fit the filter cartridge into the water tank, pressing slightly,
and push the cartridge holder back so that it audibly snaps
into place.
T Place a receptacle (at least 500 ml) under the hot water
spout.
m T Press the hot water button.
FILTERIS RINSING, water flows out of the hot water spout.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml.
Your IMPRESSA is once more ready for operation.
Descaling the machine
WARNING
38
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T If the descaling agent comes into contact with the skin or the
eyes, rinse thoroughly with clean water. Should you get any
descaling agent in your eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.
T Only use original JURA care products.
CAUTION
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
CAUTION
If the descaling agent comes into contact with sensitive surfaces,
damage cannot be ruled out.
T Remove any splashes immediately with clean water.
6 Maintenance
E The descaling programme lasts approx. 45 minutes.
E JURA descaling tablets are available from stockists.
E If you use a CLARIS filter cartridge and this is activated, or the
water hardness is set to ‘not active’, you will not be prompted
to descale the machine.
E Do not descale the machine if a CLARIS filter cartridge is fitted.
Precondition: Your IMPRESSA is ready for operation, the message
R is shown on the display.
T Open the cover of the programming buttons.
% T Press the descaling button.
The current maintenance status is shown.
% T Press the descaling button again.
START DESCALING
% T Press the descaling button to start the descaling operation.
EMPTY DRIP TRAY
T Empty the drip tray.
EMPTY COFFEE GROUNDS CONT.
T Empty the coffee grounds container.
T Replace the coffee grounds container and the drip tray.
SOLVENT IN TANK
T Remove the water tank and empty it.
T Completely dissolve the contents of one blister (three JURA
descaling tablets) in a container that holds 700 ml of water.
This may take several minutes.
T Pour the solution into the empty water tank and insert it in
the machine.
T Place three receptacles under the dual spout, the steam pipe
and the hot water pipe.
% T Press the descaling button.
MACHINE IS DESCALING, water flows from the steam pipe,
the dual spout and the hot water pipe. You can follow the
current status of descaling on the progress bar.
The process is interrupted, EMPTY DRIP TRAY.
T Empty the drip tray and replace the tray.
WATERTANK RINSE / FILL
39
6 Maintenance
T Remove the water tank and rinse it.
T Fill the water tank with fresh, cold water and reinsert.
T Empty the three receptacles and place them under the dual
spout, the steam pipe and the hot water pipe.
% T Press the descaling button.
MACHINE IS DESCALING, water flows from the steam pipe,
the dual spout and the hot water pipe.
The process is interrupted, EMPTY DRIP TRAY.
T Empty the drip tray.
EMPTY COFFEE GROUNDS CONT.
T Empty the coffee grounds container.
T Replace the coffee grounds container and the drip tray.
Your IMPRESSA is once more ready for operation.
Cleaning the bean
container
WARNING
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These residues may negatively affect
the coffee results. For this reason clean the bean container from
time to time.
Danger of injury to the fingers when the grinder is running.
T Switch the machine off with the on/off button Q before performing any work on the grinder.
T Switch the machine off at the power switch 3.
T Remove the cover of the bean container.
T Remove the remaining beans with a vacuum cleaner.
T Clean the bean container with a soft, dry cloth.
T Fill the coffee beans into the bean container and replace the
cover.
Descaling the water
tank
40
Limescale deposits may form in the water tank. To ensure correct
function of your IMPRESSA, you should descale the water tank from
time to time.
T Remove the water tank.
T If you use a CLARIS filter cartridge, remove this.
T Descale the tank with a mild conventional descaling agent
in accordance with the manufacturer’s instructions.
T Rinse the water tank with clean water afterwards.
T If you use a CLARIS filter cartridge, insert this again.
6 Maintenance
T Fill the water tank with fresh, cold water and reinsert.
41
7 Display messages
7 Display messages
Message
Cause/Result
Action
The message R is displayed. A maintenance programme is
necessary.
T Press the milk system
cleaning button 6 to activate
the maintenance status. Run
the respective maintenance
programme. The corresponding
description is contained in
section 6 ‘Maintenance’.
FILL BEANS / LEFT GRINDER One of the bean containers is
or
empty.
FILL BEANS / RIGHT GRINDER You cannot prepare coffee
products for which coffee beans
from this container are
required. It is possible to
prepare hot water or milk.
T Fill the bean container (See
Chapter 2, ‘Preparing and using
for the first time – Filling the
bean container’)
FILL WATERTANK
The water tank is empty.
You cannot prepare any coffee
products, hot water or milk
products.
T Fill the water tank (See
Chapter 2, ‘Preparing and using
for the first time – Filling the
water tank’)
EMPTY COFFEE GROUNDS
CONT.
The coffee grounds container is T Empty the coffee grounds
container and the drip tray.
full. You cannot prepare any
coffee products, but you can
prepare hot water or milk.
COFFEE GROUNDS CONT.
MISSING
The coffee grounds container is T Insert the coffee grounds
container.
missing. You cannot prepare
any coffee products, hot water
or milk products.
EMPTY DRIP TRAY
The drip tray is full. You cannot
prepare any coffee products,
hot water or milk products.
42
T Empty the drip tray.
7 Display messages
Message
Cause/Result
Action
DRIP TRAY MISSING
The drip tray is not inserted
correctly or is not inserted at
all. You cannot prepare any
coffee products, hot water or
milk products.
T Clean and dry the metal
contacts on the back of the drip
tray.
T Insert the drip tray.
PRESS BUTTON
T Press the rinse button to start
The IMPRESSA is prompting
you to start a rinse operation or rinsing or to continue the maincontinue a started maintenance tenance programme.
programme.
COFFEE SPOUT MISSING
The cover of the dual spout is
either missing or not correctly
fitted.
T Fit the cover of the dual
spout and ensure that it snaps
correctly in place.
CHECK BEAN CONTAINER
The catch of the bean container
is not pulled completely to the
front. The grinder cannot draw
in any coffee beans.
T Open the cover on the back
of the machine.
T Pull the catch completely to
the front.
43
8 Troubleshooting
8 Troubleshooting
Problem
Cause/Result
Action
Grinder is making a very loud
noise.
There are foreign objects in
the grinder.
T Please contact your JURA
service partner (see Chapter
‘JURA contact details / Legal
information’).
Insufficient foam is produced
when milk is foamed
The dual spout is dirty.
T Rinse and clean the dual
spout (refer to Chapter 6
‘Maintenance – dismantling
and rinsing the dual spout’).
Coffee only comes out in drips The coffee is ground too finely
when it is being prepared.
and obstructs the system.
T Set the grinder to a courser
setting(refer to Chapter 2,
‘Preparing and using for the
first time – Adjusting the
grinder’).
Water hardness cannot be
adjusted.
The CLARIS filter cartridge is
activated.
T Please contact your JURA
service partner, who will be
able to deactivate the CLARIS
filter cartridge.
FILL BEANS is displayed
although the bean container
has been filled.
The grinder is not yet completely filled with beans.
T Prepare a coffee speciality.
Cleaning of the coffee system
cannot be started although
the machine displays the
prompt.
The machine requests cleaning T First perform descaling or
change the filter. You can then
of the coffee system and
clean the coffee system.
descaling / filter change.
The bean monitor is dirty.
In spite of the empty bean
container, no bean is displayed
for the respective products.
T Clean the bean container
(see Chapter 6, ‘Maintenance –
Cleaning the bean container’).
EMPTY DRIP TRAY is always
displayed.
The metal contacts of the drip
tray are dirty or wet.
T Clean and dry the metal
contacts on the back of the
drip tray.
FILL WATERTANK is displayed
although the water tank is full.
The water tank float is trapped. T Descale the water tank (see
Chapter 6, ‘Maintenance –
Descaling the water tank’).
44
8 Troubleshooting
Problem
Cause/Result
Action
ERROR2 or ERROR4 is
displayed.
If the machine was exposed to
the cold for a long period of
time, heating is disabled for
safety reasons.
T Warm up the machine at
room temperature.
Other ERRORmessages are
displayed.
–
T Turn the IMPRESSA off at the
power switch 3. Please
contact your JURA service
partner (see Chapter ‘JURA
contact details / Legal
information’).
E If it was not possible to remedy the problem, please contact
your JURA service partner. The contact details are given in the
‘JURA contacts’ section on the last page of these instructions.
45
9 Transport and environmentally neutral disposal
9 Transport and environmentally neutral disposal
Transport / emptying
the system
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transportation.
In order to protect the IMPRESSA from frost during transportation,
the system must be emptied.
Precondition: The IMPRESSA is switched off (standby).
T Remove the water tank.
T Open the cover of the programming buttons.
c T Press the rinse button until SYSTEM EMPTYING appears.
A small amount of water flows from the hot water pipe and
the steam pipe. The operation stops automatically. The
IMPRESSA will switch itself off.
3 T Turn your IMPRESSA off at the power switch.
The next time you use the machine, the system must be refilled (see
Chapter 2, ‘Preparing and using for the first time – First-time use’).
Disposal
Please dispose of old machines in an environmentally neutral way.
H
46
Old machines contain valuable materials capable of being recycled
which should be salvaged for recycling. Please therefore dispose of
old machines via your regional collection system.
10 Technical data
10 Technical data
Voltage
220–240 V ~, 50 Hz
Power
CH: 1500 W
EU: 2200 W
Airborne noise emitted
Lp < 70 dB (A)
Marks of conformity
AS
Power consumption in standby mode
4.2 Wh
Pump pressure
2x static max. 15 bar
Water tank capacity
5.0 l
Bean container capacity
2x 650 g
Coffee grounds container capacity
max. 40 portions
Cable length
approx. 1.8 m
Weight
20.7 kg
Dimensions (W x H x D)
43 x 58.5 x 51cm
47
Index
Index
E
Environmentally neutral disposal 46
Espresso 22
A
Adjusting the grinder 16
Automatic switch-off 28
F
Filler funnel for cleaning tablet 4
Filling
B
Bean container 12
Bean container 4
Film
Cleaning 40
Filling 12
Multimedia 30
Filter cartridge
C
Changing 37
Inserting and activating 14
Cappuccino 23
Changing the filter
Fineness of grind
Changing the filter cartridge 37
Adjusting the grinder 16
CLARIS filter cartridge
Filter cartridge 14
Cleaning
First-time use 12
G
Grinder
Bean container 40
Milk system cleaning 33
Cleaning tablet
Filler funnel 4
Coffee 22
Coffee grounds container 4
Coffee grounds container 4
Coffee system cleaning 34
Combined cleaning 35
Control options
Adjusting the grinder 16
H
Hot water 24
Hot water pipe 4
I
Internet 10
L
Language 29
Latte macchiato 23
Default settings in programming mode 19
Cover
Bean container 4
Programming buttons 4
Water tank 4
D
Descaling
Descaling the machine 38
Machine 38
Water tank 40
Determining and adjusting the degree of
water hardness 14
Display 5
Messages 42
Display messages 42
Disposal 46
Drip tray 4
Drip tray 4
Dual spout 4
Dismantling and rinsing 33
48
M
Machine
Descaling 38
First-time use 12
Rinsing 32
Setting up 11
Switching on 17
Maintenance 32
Maintenance 32
Maintenance status
Viewing information and maintenance
status 20
Maintenance tips 32
Milk
Hot milk 23
Milk pipe 4
Milk system cleaning 33
Milky coffee 23
Index
Switch-on time
P
Timer 26
Permanent settings in programming mode
25
Power consumption
Switching off (standby) 17
Switching on
Machine 17
Technical data 47
Power switch 4
Preparation
Cappuccino 23
Espresso 22
Hot water 24
Latte macchiato 23
Milky coffee 23
Preparation at the touch of a button 22
Steam 24
Preparation at the touch of a button 18
Products
Standard products 11
Product settings 25
Programming buttons 4, 5
Programming mode
T
Technical data 47
Time and weekday 26
Time format 29
Transport 46
Troubleshooting 44
U
Unit of water amount 29
Use, first-time 12
W
Water tank 4
Descaling 40
Filling 12
Language 29
Permanent settings in programming mode
25
Product settings 25
Time and weekday 26
Time format 29
Unit of water amount 29
Prompt to take action
Symbols used 8
Proper use 6
R
Resetting the counter 21
Rinsing
Dual spout 33
Machine 32
S
Safety
Safety notes 6
Setting up
Machine 11
Standard products 11
Product buttons 5
Steam 24
Steam pipe 4
Switch-off (standby)
Automatic switch-off 28
Switch-on rinse 30
49
50
51
Art. 68411/X9/en/20091204
JURA contact details / Legal information
Your JURA dealer:
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel.: +4162 38 98 233
www.jura.com
Directives
The machine complies with the following EU directives:
Z 2006/42/EC – Machinery Directive
Z 2004/108/EC – Electromagnetic Compatibility
Technical changes
We reserve the right to make technical changes.
The illustrations used in the IMPRESSA X9 Win Manual show the
IMPRESSA X9 Win Platinum. Your IMPRESSA could incorporate
minor changes.
Feedback
Your opinion is important to us!
Use the contact link at www.jura.com.
Copyright
The Instructions for Use contain information which is protected by
copyright. It is not permitted to photocopy or translate these Instructions for Use into another language without the express written consent of JURA Elektroapparate AG.
52