Induction Hob - Nagold By Hafele

Hafele Nagold Appliances
Induction Hob
Instruction Manual / Installation Manual
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Safety Warnings
Your safety is important to us. Please read this
information before using your cooktop.
Electrical Shock Hazard
• Disconnect the appliance from the main
electricity supply before carrying out any
work or maintenance activity.
• Connection to a good earth wiring system is
essential and mandatory.
• Alterations to the domestic wiring system
must only be made by a qualified electrician.
• Failure to follow this advice may result in
electrical shock causing fatal accidents.
• Take care - panel edges are sharp.
• Failure to use caution could result in injury or
Important safety instructions
• Read these instructions carefully before
installing or using this appliance.
• No combustible material or products should be
placed on this appliance at any time.
• Please make this information available to the
person responsible for installing the appliance
as it could reduce your installation costs.
• In order to avoid a hazard, this appliance must
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
be installed according to these instructions for
• This appliance is to be properly installed and
earthed only by a Hafele authorized engineer.
• This appliance should be connected to a circuit
which incorporates an isolating switch
providing full disconnection from the power
• Failure to install the appliance correctly could
invalidate any warranty or liability claims.
Operation and maintenance
Electrical Shock Hazard
• Do not cook on a broken or cracked cooktop. If
the cooktop surface should break or crack,
switch the appliance off immediately at the
mains power supply (wall switch) and contact a
qualified technician.
• Switch the cooktop off at the wall before
cleaning or maintenance.
• Failure to follow this advice may result in
electrical shock causing fatal accidents.
Health Hazard
• This appliance complies with electromagnetic
safety standards.
• However, persons with cardiac pacemakers or
other electrical implants (such as insulin
pumps) must consult with their doctor or
implant manufacturer before using this
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
appliance to make sure that their implants will
not be affected by the electromagnetic field.
• Failure to follow this advice may result in fatal
Hot Surface Hazard
• During use, accessible parts of this appliance
will become hot enough to cause burns.
• Do not let your body, clothing or any item
other than suitable cookware contact the
Induction glass until the surface is cool.
• Metallic objects such as knives, forks, spoons
and lids should not be placed on the hob surface
since they can get hot
• Keep children away.
• Handles of saucepans may be hot to touch.
Check saucepan handles do not overhang
other cooking zones that are on. Keep handles
out of reach of children.
• Failure to follow this advice could result in
Cut Hazard
• The razor-sharp blade of a cooktop scraper is
exposed when the safety cover is retracted. Use
with extreme care and always store safely and
out of reach of children.
• Failure to use caution could result in injury or
Important safety instructions
• Never leave the appliance unattended when in
use. Over-boiling causes smoke and greasy
spillovers that may be inflammable.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
• Never use your appliance as a work or storage
• Never leave any objects or utensils on the
• Do not place or leave any magnetic objects
(e.g. credit cards, memory cards) or electronic
devices (e.g. computers, MP3 players) near the
appliance, as they may be affected by its
electromagnetic field.
• Never use your appliance for warming or
heating the room.
• After use, always turn off the cooking zones
and the cooktop as described in this manual (i.e.
by using the touch controls). Do not rely on the
pan detection feature to turn off the cooking
zones when you remove the pans.
• Do not allow children to play with the
appliance or sit, stand, or climb on it.
• Do not store items of interest to children in
cabinets above the appliance. Children climbing
on the cooktop could be seriously injured.
• Do not leave children alone or unattended in
the area where the appliance is in use.
• Children or persons with a disability which
limits their ability to use the appliance should
have a responsible and competent person to
instruct them in its use. The instructor should be
satisfied that they can use the appliance without
danger to themselves or their surroundings.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
• Do not repair or replace any part of the
appliance unless specifically recommended in
the manual. All other servicing should be done
by a qualified technician.
• Do not use a steam cleaner to clean your
• Do not place or drop heavy objects on your
• Do not stand on your cooktop.
• Do not use pans with jagged edges or drag
pans across the Induction glass surface as
this can scratch the glass.
• Do not use scourers or any other harsh
abrasive cleaning agents to clean your
cooktop, as these can scratch the Induction
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a
•This appliance is intended to be used in
household and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments; -farm houses; -by
clients in hotels, motels and other residential
type environments; -bed and breakfast type
•WARNING: The appliance and its accessible
parts become hot during use.
Care should be taken to avoid touching heating
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Children less than 8 years of age shall be kept
away unless continuously supervised.
•This appliance can be used by children aged
from 8 years and above and persons with
reduced physical,sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
•Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
•WARNING: Unattended cooking on a hob with
fat or oil can be dangerous and may result in
fire.NEVER try to extinguish a fire with water,
but switch off the appliance
and then cover flame e.g. with a lid or a fire
•WARNING: Danger of fire: do not store items
on the cooking surfaces.
• Warning: If the surface is cracked, switch off
the appliance to avoid
the possibility of electric shock, for hob surfaces
of glass-ceramic or similar material which
protect live parts
•A steam cleaner is not to be used.
•The appliance is not intended to be operated
by means of an external timer or separate
remote-control system.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Congratulations on the purchase of your new Induction Hob.
We recommend that you spend some time to read this Instruction / Installation
Manual in order to fully understand how to install correctly and operate it.
For installation, please read the installation section.
Read all the safety instructions carefully before use and keep this Instruction /
Installation Manual for future reference.
Product Overview
Top View
1. max. 1500 W zone
2. max. 2000 W zone
3. max. 1500 W zone
4. max. 2000 W zone
5. Glass plate
6. Control panel
7. ON/OFF control
Control Panel
1. Heating zone selection controls
2. Power / Timer regulating key
3. keylock control
4. ON/OFF control
5. Timer control
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
A Word on Induction Cooking
Induction cooking is a safe, advanced, efficient, and economical cooking
technology. It works by electromagnetic vibrations generating heat directly in
the pan, rather than indirectly through heating the glass surface. The glass
becomes hot only because the pan eventually warms it up.
iron pot
magnetic circuit
ceramic glass plate
induction coil
induced currents
Before using your New Induction Hob
• Read this guide, taking special note of the ‘Safety Warnings’ section.
• Remove any protective film that may still be on your Induction hob.
Using the Touch Controls
The controls respond to touch, so you don’t need to apply any pressure.
Use the ball of your finger, not its tip.
You will hear a beep each time a touch is registered.
Make sure the controls are always clean, dry, and that there is no object (e.g.
a utensil or a cloth) covering them. Even a thin film of water may make the
controls difficult to operate.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Choosing the right Cookware
• Only use cookware with a base suitable for induction
cooking. Look for the induction symbol on the
packaging or on the bottom of the pan.
• You can check whether your cookware is suitable by carrying out
a magnet test. Move a magnet towards the base of the pan. If it
is attracted, the pan is suitable for induction.
• If you do not have a magnet:
1. Put some water in the pan you want to check.
2. If
does not flash in the display and the water is heating, the pan is suitable.
• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or
copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is
the same size as the cooking zone. Use pans whose diameter is as large as the
graphic of the zone selected. Using a pot a slightly wider energy will be used at
its maximum efficiency. If you use smaller pot efficiency could be less than
expected. Pot less than 140 mm could be undetected by the hob. Always centre
your pan on the cooking zone.
Always lift pans off the Induction hob – do not slide, or they may scratch the
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Using your Induction Hob
To start cooking
1. Touch the ON/OFF control.
After power on, the buzzer beeps once, all displays
show “ – “ or “ – – “, indicating that the induction
hob has entered the state of standby mode.
2. Place a suitable pan on the cooking zone that
you wish to use.
• Make sure the bottom of the pan and the surface
Of the cooking zone are clean and dry.
3. Touching the heating zone selection control ,and
a indicator next to the key will flash
4. Select a heat setting by touching the”-“or”+”
• If you don’t choose a heat setting within 1
minute, the Induction hob will automatically
switch off. You will need to start again at
step 1.
• You can modify the heat setting at any time
during cooking.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
If the display flashes
alternately with the heat
This means that:
• you have not placed a pan on the correct cooking zone or,
• the pan you’re using is not suitable for induction cooking or,
• the pan is too small or not properly centered on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically turn off after 1 minutes if no suitable pan is
placed on it.
When you have finished cooking
1. Touching the heating zone selection
control that you wish to switch off
Turn the cooking zone off by scrolling down to”0” or touching”-“ and”+”
control together. Make sure the display shows”0”
Turn the whole cooktop off by touching the
ON/OFF control.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
4. Beware of hot surfaces
H will show which cooking zone is hot to touch. It will disappear when the
surface has cooled down to a safe temperature. It can also be used as an
energy saving function if you want to heat further pans, use the hotplate
that is still hot.
Locking the Controls
• You can lock the controls to prevent unintended use (for example children
accidentally turning the cooking zones on).
• When the controls are locked, all the controls except the ON/OFF control are
To lock the controls
Touch the keylock control. The timer indicator will show “ Lo “
To unlock the controls
1. Make sure the Induction hob is turned on.
2. Touch and hold the keylock control for a while
3. You can now start using your Induction hob.
When the hob is in the lock mode,all the controls are disable except the ON/OFF
you can always turn the induction hob off with the ON/OFF control in an
emergency,but you shall unlock the hob first in the next operation
Over-Temperature Protection
A temperature sensor equipped can monitor the temperature inside the
Induction hob. When an excessive temperature is monitored, the Induction hob
will stop operation automatically.
Detection of Small Articles
When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other
small item (e.g. knife, fork, key) has been left on the hob, the hob automatically
go on to standby in 1 minute. The fan will keep cooking down the induction hob
for a further 1 minute.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Auto Shutdown Protection
Auto shut down is a safety protection function for your induction hob. It shut
down automatically if ever you forget to turn off your cooking. The default
working times for various power levels are shown in the below table: .
Power level
Default working timer (hour) 8
When the pot is removed, the induction hob can stop heating immediately and
the hob automatically switch off after 2 minutes.
People with a heart pace maker should consult with their doctor before
using this unit.
Using the Timer
You can use the timer in two different ways:
• You can use it as a minute minder. In this case, the timer will not turn any
cooking zone off when the set time is up.
• You can set it to turn one cooking zone off after the set time is up.
• You can set the timer up to 99 minutes.
Using the Timer as a Minute Minder
If you are not selecting any cooking zone
Make sure the cooktop is turned on.
Note: you can use the minute minder even if you’re not selecting any
cooking zone.
Touch timer control , The minder indicator
will start flashing and “10” will show in the
timer display.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
3. Set the time by touching the”-“ or “+” control
of the timer
Hint: Touch the “-“ or”+” control of the timer
once to decrease or increase by 1 minute.
Hold the “-“ or “+” control of the timer to
decrease or increase by 10 minutes.
4. Touching the”-“ and “+” together, the timer is cancelled, and the”00” will
show in the minute display.
5. When the time is set, it will begin to count down
immediately. The display will show the remaining
time and the timer indicator will flash for 5 seconds.
6. Buzzer will bips for 30 seconds and the timer
indicator shows “- - “ when the setting time
Setting the timer to turn one cooking zone off
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
1. Touching the heating zone selection control
that you want to set the timer for.
Touch timer control , The minder indicator
will start flashing and “10” will show in the
timer display.
3. Set the time by touching the or control of the
Hint: Touch the”-“ or ”+” control of the timer
once will decrease or increase by 1 minute.
Touch and hold the”_” or “+” control of the timer
will decrease or increase by 10 minutes.
Touching the “-“ and “+” together, the timer is cancelled, and the “00” will
show in the minute display.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
5. When the time is set, it will begin to count down
immediately. The display will show the remaining
time and the timer indicator flash for 5 seconds.
NOTE: The red dot next to power level indicator
will illuminate indicating that zone is selected.
6. When cooking timer expires, the corresponding
cooking zone will be switch off automatically.
Other cooking zone will keep operating if they are turned on previously.
Cooking Guidelines
Take care when frying as the oil and fat heat up very quickly,
particularly if you’re using PowerBoost. At extremely high
termperatures oil and fat will ignite spontaneously and this presents a
serious fire risk.
Cooking Tips
When food comes to the boil, reduce the temperature setting.
Using a lid will reduce cooking times and save energy by retaining the heat.
Minimise the amount of liquid or fat to reduce cooking times.
Start cooking on a high setting and reduce the setting when the food has
heated through.
Simmering, cooking rice
• Simmering occurs below boiling point, at around 85˚C, when bubbles are just
rising occasionally to the surface of the cooking liquid. It is the key to delicious
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
soups and tender stews because the flavours develop without overcooking the
food. You should also cook egg-based and flourthickened sauces below boiling
• Some tasks, including cooking rice by the absorption method, may require a
setting higher than the lowest setting to ensure the food is cooked properly in
the time recommended.
Searing steak
cook juicy flavoursome steaks:
Stand the meat at room temperature for about 20 minutes before cooking.
Heat up a heavy-based frying pan.
Brush both sides of the steak with oil. Drizzle a small amount of oil into the
hot pan and then lower the meat onto the hot pan.
4. Turn the steak only once during cooking. The exact cooking time will depend
on the thickness of the steak and how cooked you want it. Times may vary
from about 2 – 8 minutes per side. Press the steak to gauge how cooked it
is – the firmer it feels the more ‘well done’ it will be.
5. Leave the steak to rest on a warm plate for a few minutes to allow it to relax
and become tender before serving.
For stir-frying
Choose an induction compatible flat-based wok or a large frying pan.
Have all the ingredients and equipment ready. Stir-frying should be quick. If
cooking large quantities, cook the food in several smaller batches.
Preheat the pan briefly and add two tablespoons of oil.
Cook any meat first, put it aside and keep warm.
Stir-fry the vegetables. When they are hot but still crisp, turn the cooking
zone to a lower setting, return the meat to the pan and add your sauce.
Stir the ingredients gently to make sure they are heated through.
Serve immediately.
Heat Settings
The settings below are guidelines only. The exact setting will depend on several
factors, including your cookware and the amount you are cooking. Experiment
with the induction hob to find the settings that best suit you.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Heat setting
delicate warming for small amounts of food
melting chocolate, butter, and foods that burn quickly
gentle simmering
slow warming
rapid simmering
cooking rice
cooking pasta
bringing soup to the boil
boiling water
Care and Cleaning
Everyday soiling on
glass (fingerprints,
marks, stains left by
food or non-sugary
spillovers on the
1. Switch the power to the
cooktop off.
2. Apply a cooktop cleaner
while the glass is still warm
(but not hot!)
3. Rinse and wipe dry with a
clean cloth or paper towel.
4. Switch the power to the
cooktop back on.
• When the power to the cooktop is
switched off, there will be no ‘hot
surface’ indication but the cooking
zone may still be hot! Take extreme
• Heavy-duty scourers, some nylon
scourers and harsh/abrasive
cleaning agents may scratch the
glass. Always read the label to
check if your cleaner or scourer is
• Never leave cleaning residue on the
cooktop: the glass may become
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Over-boiling, melts,
hot sugary spills on
the glass
Spillovers on the
touch controls
Remove these immediately
with a fish slice, palette knife or
razor blade scraper suitable for
Induction glass cooktops, but
beware of hot cooking zone
1. Switch the power to the
cooktop off at the wall.
2. Hold the blade or utensil at a
30° angle and scrape the
soiling or spill to a cool area
of the cooktop.
3. Clean the soiling or spill up
with a dish cloth or paper
4. Follow steps 2 to 4 for
‘Everyday soiling on glass’
1. Switch the power to the
cooktop off.
2. Soak up the spill
3. Wipe the touch control area
with a clean damp sponge or
4. Wipe the area completely
with a paper towel.
5. Switch the power to the
cooktop back on.
• Remove stains left by melts and
sugary food or spillovers as soon
as possible. If left to cool on the
glass, they may be difficult to
remove or even permanently
damage the glass surface.
• Cut hazard: when the safety cover
is retracted, the blade in a scraper
is razor-sharp. Use with extreme
care and always store safely and
out of reach of children.
• The cooktop may beep and turn
itself off, and the touch controls
may not function while there is
liquid on them. Make sure you wipe
the touch control area dry before
turning the cooktop back on.
Hints and Tips
Possible causes
What to do
The induction hob
cannot be turned on.
No power.
The touch controls are
The controls are locked.
Make sure the induction hob is
connected to the power supply
and that it is switched on.
Check whether there is a power
output in your home or area. If
you’ve checked everything and the
problem persists, call a qualified
Unlock the controls. See section
‘Using your induction cooktop’ for
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
The touch controls are
difficult to operate.
The glass is being
Some pans make
crackling or clicking
The induction hob
makes a low
humming noise when
used on
a high heat setting.
Fan noise coming
from the induction
Pans do not become
hot and appears in
the display.
The induction hob or a
cooking zone has
turned itself off
unexpectedly, a tone
sounds and an error
code is displayed
(typically alternating
with one or two digits
in the cooking timer
There may be a slight film of
water over the controls or you
may be using the tip of your
finger when touching the
Rough-edged cookware.
Make sure the touch control area is
dry and use the ball of your finger
when touching the controls.
Unsuitable, abrasive scourer or
cleaning products being used.
This may be caused by the
construction of your cookware
(layers of different metals
vibrating differently).
This is caused by the
of induction cooking.
See ‘Care and cleaning’.
A cooling fan built into your
induction hob has come on to
prevent the electronics from
overheating. It may continue to
run even after you’ve turned
induction hob off.
The induction hob cannot
detect the pan because it is not
suitable for induction cooking.
This is normal and needs no action.
Do not switch the power to the
induction hob off at the wall while
the fan is running.
The induction hob cannot
detect the pan because it is too
small for the cooking zone or
not properly in the center.
Technical fault.
Centre the pan and make sure that
its base matches the size of the
cooking zone.
Use cookware with flat and smooth
bases. See ‘Choosing the right
This is normal for cookware and
does not indicate a fault.
This is normal, but the noise should
quieten down or disappear
completely when you decrease the
heat setting.
Use cookware suitable for induction
cooking. See section ‘Choosing the
right cookware’.
Please note down the error
letters and numbers, switch
the power to the induction hob
off at the wall, and contact a
qualified technician.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Failure Display and Inspection
If an abnormality comes up, the induction hob will enter the protective state
automatically and display corresponding protective codes:
Possible causes
Temperature sensor failure
What to do
Please contact the supplier.
Temperature sensor of the
Please contact the supplier.
Abnormal supply voltage
Abnormal temperature
Please inspect whether power
supply is normal.
Power on after the power
supply is normal.
Please inspect the pot.
Bad induction hob heat
Please restart after the
induction hob cools down.
IGBT failure.
The above are the judgment and inspection of common failures.
Please do not disassemble the unit by yourself to avoid any dangers and
damages to the induction hob.
Technical Specification
Cooking Hob
Cooking Zones
4 Zones
Supply Voltage
220-240V~ / 400V 3N~
Installed Electric Power
Product Size
Building-in Dimensions A×B (mm)
Weight and Dimensions are approximate. Because we continually strive to
improve our products we may change specifications and designs without prior
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Selection of installation equipment
Cut out the work surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 5 cm space shall be
preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select
heat-resistant work surface material to avoid larger deformation caused by the
heat radiation from the hotplate. As shown below:
50 mini
Under any circumstances, make sure the Induction cooker hob is well ventilated
and the air inlet and outlet are not blocked. Ensure the Induction cooker hob is
in good work state. As shown below
Note: The safety distance between the hotplate and the cupboard above
the hotplate should be at least 760mm.
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
50 mini
20 mini
Air intake
Air exit 5mm
Before you install the hob, make sure that
• the work surface is square and level, and no structural members interfere with
space requirements
• the work surface is made of a heat-resistant material
• if the hob is installed above an oven, the oven has a built-in cooling fan
• the installation will comply with all clearance requirements and applicable
standards and regulations
• a suitable isolating switch providing full disconnection from the mains power
supply is incorporated in the permanent wiring, mounted and positioned to
comply with the local wiring rules and regulations.
The isolating switch must be of an approved type and provide a 3 mm air gap
contact separation in all poles (or in all active [phase] conductors if the local
wiring rules allow for this variation of the requirements)
• the isolating switch will be easily accessible to the customer with the hob
• you consult local building authorities and by-laws if in doubt regarding
• you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for
the wall surfaces surrounding the hob.
When you have installed the hob, make sure that
• the power supply cable is not accessible through cupboard doors or drawers
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
• there is adequate flow of fresh air from outside the cabinetry to the base of the
• if the hob is installed above a drawer or cupboard space, a thermal protection
barrier is installed below the base of the hob
• the isolating switch is easily accessible by the customer
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do
not apply force onto the controls protruding from the hob.
Adjusting the bracket position
Fix the hob on the work surface by screw 2 brackets on the bottom of hob(see
picture) after installation.
Adjust the bracket position to suit for different table top thickness.
1. The induction hotplate must be installed by qualified personnel or technicians.
We have professionals at your service. Please never conduct the operation by
2. The hob will not be installed directly above a dishwasher, fridge, freezer,
washing machine or clothes dryer, as the humidity may damage the hob
3. The induction hotplate shall be installed such that better heat radiation can be
ensured to enhance its reliability.
4. The wall and induced heating zone above the table surface shall withstand
5. To avoid any damage, the sandwich layer and adhesive must be resistant to
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
Connecting the hob to the mains power supply
This hob must be connected to the mains power supply only by a suitably qualified
Before connecting the hob to the mains power supply, check that:
1. the domestic wiring system is suitable for the power drawn by the hob.
2. the voltage corresponds to the value given in the rating plate
3. the power supply cable sections can withstand the load specified on the rating plate.
To connect the hob to the mains power supply, do not use adapters, reducers, or
devices, as they can cause overheating and fire.
The power supply cable must not touch any hot parts and must be positioned so that its
temperature will not exceed 75˚C at any point.
Check with an electrician whether the domestic wiring system is suitable without
alterations. Any alterations must only be made by a qualified electrician.
The power supply should be connected in compliance with the relevant standard,
or a single-pole circuit breaker. The method of connection is shown below.
• If the cable is damaged or to be replaced, the operation must be carried out
the by after-sale agent with dedicated tools to avoid any accidents.
• If the appliance is being connected directly to the mains an omnipolar
circuit-breaker must be installed with a minimum opening of 3mm between
• The installer must ensure that the correct electrical connection has been made
and that it is compliant with safety regulations.
• The cable must not be bent or compressed.
• The cable must be checked regularly and replaced by authorised technicians
Hafele Article Number (538.01.701)
Hafele Nagold Appliances
This appliance is labeled in compliance with European directive
2002/96/EC for Waste Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is disposed of correctly, you will
help prevent any possible damage to the environment and to
human health, which might otherwise be caused if it were disposed
of in the
wrong way.
The symbol on the product indicates that it may not be treated as
normal household waste. It should be taken to a collection point for
the recycling of electrical and electronic goods.
dispose this product
as unsorted municipal
waste. Collection of
such waste separately
for special treatment is
This appliance requires specialist waste disposal. For further
information regarding the treatment, recover and recycling of this
product please contact your local council, your household waste
disposal service, or the shop where you purchased it.
For more detailed information about treatment, recovery and
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased
the product.
Hafele Article Number (538.01.701)
Download PDF