Additional Instruction - Duerkopp

Threading procedure
878 PREMIUM – Facts and USP
Programmable electronic
thread tension
(optional)
Programmable
top roller lift
(max. 13 mm)
Operation panel
OP 3000
Programmable
top roller constant
pressure
© Dürkopp Adler AG
Basic
information
Stop button
for service
Programmable stitch length
adjustment (max. 7 mm)
including back tack and
short stitch length
Integrated LED
sewing light
Automatic thread trimmer
(length of remaining
thread approx. 10 mm)
M-TYPE PREMIUM
Integrated bobbin winder
with winding assistant
Keypad for the
most common
functions
Bottom wheel feed with
possibility of differential
between the top roller
and wheel feeder
(without needle transport)
Powerful
direct drive
Vertical hook
L (26 mm)
Electronic hand wheel
(Jog-Dial)
Thread monitor
for hook thread
(optional)
Blocking machine run
after opening the cover
hook (optional)
0791 878701 EN - 00.0 - 05/2017
© Dürkopp Adler AG
Control unit DAC comfort
(max. 999 sewing programs
with max. 30 seam sections)
Electronic knee switch
with a choice of function
0791 878701 EN - 00.0 - 05/2017
© Dürkopp Adler AG
0791 878701 EN - 00.0 - 05/2017
Programming mode
Programmable favorite
button
TEACH-IN
1. Select programing mode.
1. Press
Stitch length
Thread tension (optional)
button.
〉〉
Program 000 – Manual mode
.
2. Press
2. Set the parameters.
button.
3. Select
and sew for the first seam section.
4. Press ▲ button to activate the next seam section; if necessary,
readjust parameters and sew for the next seam section.
Top roller pressure
Differential
Other parameters
3. Press
→ Perform for all desired seam sections.
5. Press pedal back → Program is saved, display
switches to Edit mode.
button.
1
0,2
→ Fine adjustment is possible.
4. Press OK button.
Assigning functions to
the favorite button
1. Press
→ Press
button.
Change of
difference
sense
Automatic
material
thickness
detection
MANUAL PROGRAMMING (Edit mode)
1. Press ► button to select
2. Press
0791 878701 EN - 00.0 - 05/2017
Press
button to add a seam section.
5. Enter values for the selected seam section.
→ Perform for all desired seam sections.
6. Press ESC → Program is saved.
0791 878701 EN - 00.0 - 05/2017
© Dürkopp Adler AG
→ Program is saved.
1 seam section.
button to add a seam section.
3. Enter parameters for the selected seam section.
4. Press ▲ button to activate the next seam section.
© Dürkopp Adler AG
ESC
Delete program
1. Select program to be delete.
2. Press P button.
Stitch counter
(1) Threading mode
(2) Back tack suppression/recall
(3) Top roller position
(4) Needle position (up/down)
(5) New program
(6) Bobbin mode
(7) Other functions
2. Press desired function and favorite button at the same time.
→ Favorite button has been assigned; function appears on the start screen.
© Dürkopp Adler AG
+
Use numeric buttons to change program number.
0791 878701 EN - 00.0 - 05/2017
3. Press
button.
4. Press
button.
→ Program is deleted.
5. Press ESC .
→ Program selection is active.
© Dürkopp Adler AG
0791 878701 EN - 00.0 - 05/2017