Condenser
Sensor Dryer
DSC64W
DSC64S
Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and passed
through a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep it for
future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
B
Important safety information. Warning for hazardous situations with regard to life and property.
Caution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
C
Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect
the environment by dropping it off in the municipal receptacles provided for this
purpose. Your appliance also contains a great amount of recyclable material.
It is marked with this label to indicate the used appliances that should not be
mixed with other waste. This way, the appliance recycling organised by your
manufacturer will be done under the best possible conditions, in compliance with
European Directive 2002/96/EC on Waste Electrical and Electronic Equipment.
Contact your town hall or your retailer for the used appliance collection points
closest to your home. We thank you doing your part to protect the environment.
2960310667_EN/240113.1012
A
TABLE OF CONTENTS
1 Your Dryer
4
Overview..............................................4
Technical Specifications........................5
2 Important safety information6
General safety......................................6
Intended use........................................7
Children’s safety...................................7
3 Installation
8
Appropriate installation location............8
Removing the transportation safety
assembly..............................................8
Under counter installation.....................8
Mounting over a washing machine........8
Connection to water drain;...................8
Adjusting the feet..................................9
First use...............................................9
Disposing of packaging material...........9
Transportation of the machine..............9
Disposing of the old machine................9
4 Electrical Connection
10
Attention!............................................10
Electrical requirements........................10
Fitting a different plug ........................10
Washer/dryer combination..................10
5 Initial preparations for drying11
Things to be done for energy saving:..11
Laundry suitable for drying in the
machine.............................................11
Laundry unsuitable for drying in the
machine.............................................11
Preparing laundry for drying................12
Correct load capacity.........................12
6 Selecting a Programme and
Operating Your Machine
13
Control panel......................................13
Preparing the machine........................14
Programme selection..........................14
Programme selection and consumption
table...................................................15
Auxiliary function.................................16
Warning indicators..............................16
Time delay..........................................16
Starting the programme......................16
Progress of programme......................16
Changing the programme after it has
started................................................16
Child-proof lock..................................17
Finishing by canceling the programme.17
End of programme.............................18
7 Maintenance and cleaning 20
Filter Cartridge / Door Inner Surface....20
Sensor ..............................................20
Water tank;.........................................21
For the condenser .............................21
8 Suggested solutions for
problems
23
9 Guarantee
24
What is covered?................................24
What is not covered?..........................24
Important notes..................................24
10 Service
25
1 Your Dryer
Overview
7
1
6
5
2
4
3
1- Control panel
5- Rating plate
2- Kick plate opening tab
6- Fluff filter
3-Adjustable feet
7- Power cord
4-Kick plate
4 EN
Technical Specifications
EN
2
Height (adjustable)
84,6 cm
Width
59,5 cm
Depth
53 cm
Capacity (max.)
6 kg
Weight (net)
36 kg
Voltage
Rated power input
See rating plate
Model code
Type label is located behind the loading door.
Specifications of this appliance may change without notice to improve the quality of the product.
Figures in this manual are schematic and may not match your product exactly.
Values stated on the machine labels or in the documentation accompanying it are obtained in
laboratory in accordance with the relevant standards. Depending on operational and environmental
conditions of the appliance, values may vary.
5 EN
2 Important safety instructions
This section includes safety information that
will help protection from risks of personal
injuries or damages. Failure to follow these
instructions shall cause any warranty to
become void.
General safety
• Never place the machine on a carpetcovered floor, otherwise, lack of airflow
beneath the machine may cause electrical
parts to overheat. This will cause problems
with your machine.
• If the power cable or mains plug is
damaged, you must call Authorised Service
Agent for repair.
• The product should not be plugged in
during installation, maintenance and repair
works. Such works should always be made
by the technical service. Manufacturer shall
not be held responsible for damages arising
from processes carried out by unauthorised
persons.
• Connect the product to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
• Operate your product at temperatures
between +5°C and +35°C.
• Do not use electrical devices in the product.
• Do not connect the air exit of the product
to the exit ducts which are used for the
exhaust fumes of the devices operating
with gas or other types of fuel.
• You must provide enough ventilation in
order to prevent gases exiting from devices
operating with other types of fuels including
the naked flame from accumulating in the
room due to the back fire effect.
• Always clean the lint filter before or after
each loading.
• Never operate your dryer without the lint
filter installed.
• Do not allow fibre, dust and dirt
accumulation around the exhaust exit and
at adjacent areas.
• Power cable plug must be within easy
reach after installation.
• Do not use extension cords, multi-plugs
or adaptors to connect the dryer to power
supply in order to decrease the risk of
electric shock.
• Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket with
a suitable one.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry unwashed items in the dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
• Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
• Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
• This product must be earthed. Grounding
installation decreases the risk of electric
shock by opening a path with low
resistance for the electricity flow in case of
a malfunction or failure. Power cable of this
product is equipped with a conductor and
a grounding plug that allows for grounding
the product. This plug must be installed
appropriately and inserted into a socket
which is grounded in accordance with the
local laws and regulations.
• Do not install the product behind a door
with a lock, sliding door or a door that has
a hinge against the hinge of the dryer.
• Do not install or leave this product in
places where it will be exposed to outdoor
conditions.
• Do not tamper with the controls.
6 EN
• Do not perform any repair or part replacing
procedures on the product even if you
know or have the ability to perform unless
it is clearly suggested in the operating
instructions or the published service
manual.
• Inside and exhaust duct of the product
must be cleaned by the qualified service
personnel periodically.
• Wrong connection of grounding conductor
of the product can cause electric shock. If
you have any suspect about the grounding
connection, have it checked by a qualified
electrician, service representative or service
personnel.
• Do not reach into the machine when the
drum is spinning.
• Unplug the machine when it is not in use.
• Never wash down the appliance with water!
There is the risk of electric shock! Always
disconnect by unplugging from the mains
before cleaning.
• Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug only.
Do not operate the machine if the power
cable or plug is damaged!
• Never attempt to repair the machine
yourself, otherwise, you will be putting your
life and others’ lives in danger.
• For malfunctions that cannot be solved by
following the information given in the safety
instructions:
Turn off the machine and contact an
authorised service agent.
• Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer quickly in
order to hang them and dissipate the heat.
• Remove the door of the drying
compartment before decommissioning or
disposing of the product.
• The final step of the drying cycle (cooldown cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
• Fabric softeners or similar products should
be used as specified by the fabric softener
instructions.
• Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result if
metal reinforcements come loose during
drying.
• Check all garments for forgotten lighters,
coins, metal pieces, needles, etc. before
loading.
• At times when your dryer is not in use or
after the laundry is taken out following the
completion of drying process, turn off by
using the On/Off button. In cases when
the On/Off button is on (while the dryer
is energized), keep the door of the dryer
closed.
Intended use
• This product has been designed for
domestic use. It should not be used for
other purposes.
• Use the product only for drying laundry that
are marked accordingly.
• Dry only those articles in your product that
are stated in this manual.
• This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they
are attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of the
product.
Children’s safety
• Electrical appliances are dangerous for
the children. Keep children away from the
machine when it is operating. Do not let
them tamper with the machine.
• Packaging materials are dangerous to
children. Keep the packaging materials out
of reach of children or dispose them by
classifying according to waste directives.
• Do not allow children sit/climb on or enter
in the product.
• Children should be supervised to ensure
that they do not play with the product.
• Close the loading door when you leave the
area where the product is located.
7 EN
3 Installation
A Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
Appropriate installation location
• Install the product in an environment which
has no risk of freezing and is in a stable and
level position.
• Operate your product in a well ventilated,
dust-free environment.
• Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden plinths.
• Do not place your product on a long pile
rug or on similar surfaces.
• Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
• Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
BDo not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls of
other furniture.
Removing the transportation
safety assembly
ARemove the transportation safety assembly
before using the product for the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum that
contains a piece of styrofoam. Hold it from
its section marked with XX.
3. Pull the nylon towards yourself and remove
the transportation safety assembly.
AMake sure that you have removed
the transportation safety assembly
(nylon+styrofoam pieces) before using the
product for the first time. Do not leave any
items inside the drum.
Under counter installation
• The product should never be operated
without the top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in
a cupboard.
Mounting over a washing machine
• A fitting device should be used between
the two machines when installing above
a washing machine. The bracket must be
installed by the Authorised Service Agent.
• Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
Connection to water drain;
In products equipped with a condenser unit
the water accumulated during the drying cycle
is collected in the water tank. You should drain
the accumulated water after each drying cycle.
You can directly send the accumulated water
out through the water drain hose supplied with
the machine instead of periodically draining the
water collected in the water tank.
Connecting the water drain hose;
8 EN
CNever unscrew the adjustable feet from
their housings.
First use
1. Remove the hose on the machine by
pulling it out from its end. Do not use any
tools to take out the hose.
2. Connect the special drain hose supplied
with the machine to the pipe fitting.
3. The other end of the drain hose can be
directly connected to the wastewater
drain or to the washbasin. The fitting
must always be secured in all types of
connections. Your house may be flooded
if the hose gets out of its housing during
water discharge.
Important:
• The hose should be attached to a height of
maximum 80 cm.
• You must be careful not the pinch or bend
the hose.
• The end of the hose should not be bent,
it should not be stepped on and it must
not be folded between the drain and the
machine.
Adjusting the feet
In order to ensure that your machine operates
more silently and vibration-free, it must stand
level and balanced on its feet. Balance the
machine by adjusting the feet.
Rotate the feet to adjust until the machine
stands level and firmly.
• To have the product ready for operation
before calling the authorised service agent,
make sure that its location and power
supply installations are appropriate. If they
are not, call a qualified electrician to have
any necessary arrangements carried out.
• Make sure that the power connections of
the product are in accordance with the
instructions given in relevant chapters of
this manual.
Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place out
of reach of children. Packaging materials of
your product are manufactured from recyclable
materials. Sort and dispose of them in
accordance with recycled waste instructions.
Do not dispose of them with normal domestic
waste.
Transportation of the machine
1. Unplug the machine from the mains.
2. Remove the water drain and vent
connections (if any).
3. Drain water remaining in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your machine.
Before disposing of your old machine, cut off
the power cable plug and make the loading
door lock unusable to avoid dangerous
conditions to children.
9 EN
4 Electrical Connection
Make sure that you have an earthed power
outlet socket rated at 13 amps (minimum).
A Do not operate without the top cover
Attention!
When installed, the socket must be reachable
after installation, or a separate switch (which
can disconnect the two poles) must be used
in the installation. Check for suitability.
For a permanent connection, a master switch
with at least 3mm contact clearance and
minumum 13 A rating must be used.
Electrical requirements
Before you insert the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
We recommend that this appliance be
connected to the mains supply via a suitable
switched and fused socket in a readily
accessible position.
Should the mains lead of the appliance
become damaged or need replacing at any
time, it must be replaced by a special purpose
made mains lead which can only be obtained
from a Authorised Service Agent.
fitted. Risk of injury.
A Important
Fitting a different plug
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green (earth)
wire to the terminal in the plug marked ‘E’ or
with the symbol or coloured green and yellow
or green.
2 Connect the blue (neutral) wire to the
terminal in the plug marked ‘N’ or coloured
black.
3 Connect the brown (live) wire to the terminal
in the plug marked ‘L’ or coloured red.
With the alternative plugs a 13A fuse must
be fitted either in the plug or adaptor or in the
main fuse box. If in doubt contact a qualified
electrician.
Green and yellow
or green
A Warning
This appliance must be earthed
If the fitted moulded plug is not suitable for
your socket, then the plug should be cut off
and an appropriate plug fitted.
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse need
to be replaced an ASTA approved BS1362
fuse of the same rating must be used. Do not
forget to refit the fuse cover. In the event of
losing the fuse cover, the plug must not be
used until a replacement fuse cover has been
fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the
pin face of the plug. Fuse covers are available
from any good electrical store.
In order to avoid hazards, damaged supply
cord should be replaced by the manufacturer,
its service agent or similarly qualified people.
Built-under installation
This appliance can be installed under a
worktop.
N
Blue or black
L
Brown or red
Washer/dryer combination
Do not stack washing machine on top of
the tumble dryer. This would damage both
appliances and guarantees would become
void. It is also unsafe to stack an appliance
on top of another without using a suitable
and approved stacking kit obtained from the
manufacturer of the appliances.
• A special stacking kit is required as an
optional extra please contact customer
service.
10 EN
5 Initial preparations for drying
Things to be done for energy
saving:
• Make sure that you operate the product
at its full capacity but pay attention to not
exceeding it.
• Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
• Pay attention to dry same types of laundry
together.
• Follow the instructions in the user manual
for programme selection.
• Make sure that sufficient clearance is
provided at the front and rear side of the
dryer for air circulation. Do not block the
grill at the front side of the product.
• Do not open the door of the machine
during drying unless necessary. If you must
certainly open the door, pay attention not to
keep it open for a long time.
• Do not add new (wet) laundry during
drying.
• Lint and fibres released from the laundry to
the air during the drying cycle are collected
in the “Lint Filter”. Make sure that you clean
the filters before or after each drying.
• In models with condenser, make sure that
you clean the condenser regularly at least
once every month or after every 30 drying
cycles.
• In vented models, follow the hose
connection rules in the user manual and
pay attention to the hose cleaning.
• Ventilate the room, where the dryer is
located, well during drying.
• For power saving in models with lamps, at
times when your dryer is not in use, keep
the door closed if the On/Off button is
pressed (if the dryer is energized).
Laundry suitable for drying in the
machine
CAlways follow the suggestions on the
laundry labels. Dry only the laundry having
a label stating that they are suitable for
drying in a dryer and make sure that you
select the appropriate programme.
A B C D
Low
l n m
o p q
Laundry unsuitable for drying in
the machine
• Laundry items with metal attachments such
as belt buckles and metal buttons can
damage your dryer.
• Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
• Laundry made of delicate and valuable
fabrics as well as lace curtains can be
creased. Do not dry them in the dryer!
• Do not dry items made of hermetic fibres
such as pillows and quilts in the dryer.
• Laundry made of foam or rubber will be
deformed.
• Do not dry laundry containing rubber in the
dryer.
• Do not dry laundry exposed to petroleum,
oil, combustible or explosive agents in the
dryer even if they are washed beforehand.
• Overly wet laundry or laundry with dripping
water must not be put into the dryer.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
11 EN
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry your unwashed laundry in the
dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
• Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
• Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
• Do not dry the underwear reinforced with
metal parts in the dryer. If these metal
reinforcements loosen and break during
drying, they will damage your dryer.
Preparing laundry for drying
• Check all laundry items before loading them
into the product to make sure that there are
no lighters, coins, metal items, needles and
etc. in their pockets or on any part of them.
• Fabric softeners and similar products must
be used in accordance with the instructions
of the manufacturer of the relevant
products.
• All laundry must be spun at the highest spin
speed that your washing machine allows
for the laundry type.
• Laundry may be tangled after washing.
Separate your laundry before placing them
into your dryer.
• Sort your laundry according to their types
and thicknesses. Dry the same type of
laundry together. E.g.: fine kitchen towels
and table cloths dry faster than the thick
bath towels.
Correct load capacity
A Consider the information in the
“Programme Selection Table”. Always start
the programme in accordance with the
maximum load capacity.
CAdding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance will
degrade when the machine is overloaded.
Furthermore, your dryer and your laundry
can be damaged.
CPlace your laundry into the drum loosely so
that they will not get tangled.
Following weights are given as examples.
Home articles
Cotton quit covers (double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
Bath towels
Hand towels
Garments
Blouses
Cotton shirts
Shirts
Cotton dresses
Dresses
Jeans
Handkerchiefs (10 pieces)
T-Shirts
Loading
Approximate
weights (g)
1500
1000
500
350
700
250
100
700
350
Approximate
weights (g)
150
300
200
500
350
700
100
125
• Open the loading door.
• Place laundry items loosely into the dryer.
• Push the loading door to close. Ensure that
no items are caught in the door.
12 EN
6 Selecting a Programme and Operating Your Machine
Control panel
1
2
3
7
4
6
5
1. Filter cleaning warning light
5. Programme selection knob
2. Programme follow-up indicator
6. Start/Pause/Cancel button
Warning light turns on when the filter is full.
Used to follow-up the progress of the
current programme.
Used to select a programme.
Used to start, pause or cancel the
programme.
3. Cancel audio warning
7. Water tank warning light*
4. On/Off button
8. Time delay selection button
Used to cancel the audio warning given at
the end of the programme.
Used to turn on and off the machine.
13 EN
Warning light turns on when the water tank
is full.
Used to set the time delay.
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
CPressing the “On/Off” button does not
necessarily mean that the programme has
started. Press “Start/Pause/Cancel” button
of the machine to start the programme.
Programme selection
Decide the appropriate programme from
the table below which includes drying
temperatures in degrees. Select the desired
programme with the programme selection
button.
Extra dry
Cupboard
dry
Normal dry
Iron Dry
.
C
Dry at high temperature only
for cotton laundry. Thick and
multi layered laundry (E.g.:
towels, linens, jeans) are dried
in a way that they do not
require ironing before placing
in the wardrobe.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do not
require ironing before placing
in the drawers.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do not
require ironing before placing
in the drawers, but more
than those in the ready to
wearoption.
Normal laundry (E.g., Shirts,
dresses) are dried ready to be
ironed.
For further programme details, see,
“Programme Selection Table”
Main programmes
Depending on the type of laundry, the following
main programmes are available:
Cottons
You can dry your durable laundry with this
programme. Dries at high temperature. It is
recommended to use for your cotton items
(such as bed sheets, quilt cover, underclothing,
etc.).
Synthetics
You can dry your less durable laundry with this
programme. It dries at a lower temperature
compared to the cottons programme. It is
recommended for your synthetic laundry (such
as shirts, blouses, synthetic/cotton blended
laundry, etc.).
CDo not dry curtains and lace in your
machine.
Anti-creasing
A 2-hour anti creasing programme to prevent
laundry from creasing will be activated if
you do not take the laundry out after the
programme is over. This programme rotates
the laundry in 10-minute intervals to prevent
creasing.
Special programmes
For special cases, there are also extra
programmes available:
CAdditional programmes may differ
according to the model of your machine.
•Xpress 35’ min.
You can use this programme to dry the cottons
that are spun at high speeds in your washing
machine. It can dry your 2 kg Cotton laundry (3
Shirts / 5 T-Shirts) within 35 minutes.
C In order to obtain better results from the
dryer programmes, your laundry must be
washed with suitable programme and spun
at the recommended spin speeds in your
washing machine.
• Shirts
Dries the shirts in a more sensitive way so that
they are less creased and ironed easily.
C Shirts may contain little amount of
dampness at the and of the programme.
It is advised not to leave the shirts in the
dryer.
•Jeans
You can use this programme to dry the jeans
that are spun at high speeds in your washing
machine.
C Review the relevant part of the programme
table.
•Delicates
You can dry at a lower temperature your very
delicate laundry (silk blouses, fine underwear,
etc.) that are suitable for drying or laundry
which is advised to be hand-washed.
CIt is recommended to use a cloth bag to
avoid certain delicate garments and laundry
from getting creased or damaged. Take
your garments immediately out of the dryer
14 EN
and hang them after the programme ends
in order to prevent them being creased.
• Freshen Up
Only ventilation is performed for 10 minutes
without blowing hot air. You can air your
clothes that have been kept at closed
environments for a long time thanks to this
programme to deodorize unpleasant odours.
•Timer programmes
You can select one of the 10 min., 20 min.,
40 min. and 60 min. timer programmes to
achieve the desired final drying level at low
temperatures. Programme dries at the selected
time regardless of the drying temperature.
15 EN
Programme selection and consumption table
EN
Programmes
Capacity (kg)
Spin speed in
washing machine
(rpm)
Approximate
amount of
remaining
humidity
Drying time
(minutes)
Cottons / Coloreds
A
Cupboard dry
6
1200-1000
% 60
105
A
Normal dry
6
1200-1000
% 60
109
A
Iron dry
6
1200-1000
% 60
80
2
1400-1000
%50
35
Xpress 35 min.
Shirts
1.5
1000-800
%50
39
Jeans
4
1200-1000
%50
80
Cupboard dry
3
800
% 40
40
Cupboard dry
1,5
800
% 40
32
Capacity (kg)
Spin speed in
washing machine
(rpm)
Cottons linen cupboard dry
6
1000
% 60
3.90
Cottons iron dry
6
1000
% 60
2.88
Synthetics cupboard dry
3
800
% 40
1.28
Synthetics
B
Delicates
B
Energy consumption values
Programmes
Approximate
Energy
amount of
consumption
remaining
value kWh
humidity
* : Energy Label standard programme (EN 61121:2012)
All values given in the table have been fixed according to EN 61121:2012 Standard. These values
may deviate from the table according to the laundry type, laundry spin speed, environmental
conditions and voltage fluctuations.
16 EN
Auxiliary function
Cancel audio warning
Your dryer will give an audio warning when the
programme comes to an end. If you do not
want to hear the audio warning, press “Cancel
Audio Warning” button. The relevant light
will turn on when this button is pressed and
an audio warning will not be given when the
programme comes to an end.
CYou can select this function either before or
after the programme starts.
Warning indicators
CWarning indicators may differ according to
the model of your dryer.
Filter cleaning
A warning light will turn on to remind filter
cleaning after the programme finishes.
CIf the filter cleaning warning light lights up
continuously, please refer to, “Suggested
solutions for problems”.
Canceling the time delay
If you want to cancel the time delay countdown
and start the programme:
1. Press “Start/Pause/Cancel” button for
about 3 seconds.
2. Press “Start/Pause/Cancel” button to start
the programme right away.
Starting the programme
Water tank
Warning light starts flashing when the tank is
filled with water. The dryer stops operating if
the warning light turns on when a programme
is running. Drain the water in the water tank to
restart the dryer. Press “Start/Pause/Cancel”
button to start the programme after you have
emptied the water tank. The warning light turns
off and the programme resumes operating.
Time delay
4. Delayed operation of the selected
programme is started by pressing the
“Start/Pause/Cancel” button after selecting
the time delay.
C Additional laundry may be loaded / taken
out during the time delay period.
C During the time delay period, laundry is
rotated for 4 seconds in every 10 minutes
to prevent creasing.
If you wish to dry your clothes at a later time,
thanks to the time delay function, you can delay
the programme start up to 3 hours, 6 hours or
9 hours.
1. Open the loading door and put the laundry
in.
C Make sure that all air outlets are open,
door filter is cleaned and the water tank is
empty.
2. Set the drying programme and, if required,
the auxiliary functions.
3. When the time programming button is
pressed once, a 3 hour delay is selected
and the relevant led lights. When the same
button is pressed again, 6 hours; and if
pressed once more, 9 hours delay will be
selected. If the time programming button
is pressed one more time, time delaying
function will be cancelled. Set the time
delay as you require.
1. Press “Start/Pause/Cancel” button to start
the programme.
2. Light of the “Start/Pause/Cancel” button
will turn on to indicate that the programme
has started.
Progress of programme
Progress of a running programme is shown
through the programme follow-up indicator.
At the beginning of every programme step, the
relevant indicator LED will light up and light of
the completed step will turn off.
“Drying”:
- Drying level will be illuminated during the whole
drying process until the drying degree reaches
“iron dry”.
“Iron Dry”:
- Starts to illuminate when the drying degree
reaches “iron dry” step and remains illuminated
until the next step.
“Cupboard dry”:
Starts to illuminate when the drying degree
reaches “Ready to wear” step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the programme comes to an
end and anti-creasing function is activated.
C If more than one LED light up or
17 EN
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after it
has started
You can use this feature to dry your clothes
under higher or lower temperatures after your
dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to start
the programme.
CPress “Start/Pause/Cancel” button for
3 seconds to cancel the programme or
turn the programme selection knob in any
direction to end the programme while the
machine is running. Water tank and filter
cleaning warning lights turn on to warn the
user when the programme is cancelled by
pressing the “Start/Pause/Cancel” button
for 3 seconds. However, the warning
lights do not turn on when the programme
is cancelled by turning the programme
selection knob. Only the drying light turns
on and the machine remains in hold until
a new programme is selected and the
“Start/Pause/Cancel” button is pressed.
Child-proof lock of the machine should
not be active in order to perform these
two operations. If the child-proof lock is
active, deactivate it before performing these
operations.
the machine intermingle with wet clothes
and the result will be wet laundry after the
drying process is over.
CLaundry may be added or taken out
as much as desired during a drying
process, but this process will extend the
programme duration and increase energy
consumption since the drying will be
interrupted continuously. Therefore, it is
recommended to add laundry before the
drying programme has started.
Child-proof lock
There is a child-proof lock to prevent any
programme interruption due to the pressing of
button while the programme is running. The
loading door and all buttons except the “On/
Off” button on the control panel are deactivated
when the child-proof lock is active.
Press the “Start/Pause/Cancel” and “Cancel
audio warning” buttons simultaneously for 3
seconds to activate the child-press lock.
To start a new programme after the programme
is over or to interrupt the programme, the childproof lock should be deactivated. Press the
same buttons for 3 sec. again to deactivate the
child-proof lock.
CChild-proof lock is deactivated when the
machine is restarted by pressing the On/Off
button.
Adding/removing laundry in standby
mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to start
the programme.
CAny laundry added after the drying process
has started may cause the dried clothes in
C Press the relevant buttons for 3 seconds
to activate the child-proof lock. A long
beep will be heard and the child-proof lock
will be activated. A double beep will be
heard if you press any button or turn the
programme selection knob while the childproof lock is active. Press the buttons for 3
seconds to deactivate the child-proof lock.
Single beep will be heard and child-proof
lock will be deactivated.
A A double beep will be heard if you turn
the programme selection knob when the
machine is running and the child-proof lock
18 EN
is active. If you deactivate the child-proof
lock without returning the programme
selection knob to its previous position, the
programme will be terminated since the
position of the programme selection knob
is changed. The drying light turns on and
the machine remains on hold until a new
programme is selected and the “Start/
Pause/Cancel” button is pressed.
Finishing by cancelling the
programme
To cancel any selected programme:
Press “Start/Pause/Cancel” button for about 3
seconds. The “Filter cleaning”, “Water tank” and
“End/ Anti-creasing” warning lights will turn on
at the end of this period for reminding purposes.
A As the inside of the dryer will be excessively
hot when you cancel the programme while
the dryer is running, activate the ventilation
programme to cool it down.
End of programme
The “End/Anti-creasing”, “Filter cleaning” and
“Water tank” warning lights on the programme
follow up indicator will turn on when the
programme comes to an end. The door can be
opened and the machine becomes ready for a
second cycle.
Press “On/Off” button to turn off the dryer.
CFinal step of the drying cycle (cooling step)
is performed without heat application in
order to keep the items at a temperature
that would not harm them.
CA 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry out
after the programme has come to an end.
CIf you will not take the laundry out
immediately, do not stop the dryer before
the drying process is complete.
CClean the filter after each drying (please
see, Filter cleaning).
CDrain the water tank after each drying
(please see, Water tank)
19 EN
7 Maintenance and cleaning
Filter Cartridge / Door Inner
Surface
Lint and fibres released from the laundry to the
air during the drying cycle are collected in the
“Filter Cartridge”.
CSuch fibre and lint are generally formed
during wearing and washing.
CAlways clean the filter and the inner
surfaces of the cover after each drying
process.
CYou can clean the filter and filter area by
vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up and
open the filter.
3. Clean lint, fibre, and cotton by unravelling
by hand or with a soft piece of cloth.
4. Close the filter and place it back into its
seat.
C Clogging may arise on the filter surface
after using your machine for some time; if
this occurs, wash the filter with water and
dry it before using again.
C
Sensor
There are humidity sensors in your dryer that
detect whether the laundry is dry or not.
To clean the sensor:
1. Open the loading door of the dryer.
2. Allow the machine to cool down if drying
has been carried out.
3. Wipe the metal sensors with a soft cloth,
dampened with vinegar and dry them.
CClean metal sensors 4 times a year.
A Never use solvents, cleaning agents
or similar substances when cleaning
since these materials can cause fire and
explosion!
Clean the entire inner surface of the door
and door gasket by wiping with a damp
cloth.
20 EN
Water tank;
The moisture in the damp laundry is taken from
the laundry and condensed. Drain the water
tank after each drying cycle or during drying
when “Water tank” warning light turns on.
A Condensed water is not drinkable!
A Never take out the water tank when the
programme is running!
If you forget to drain the water tank, your dryer
will stop during the following drying cycles
when the water tank is full and the “Water
tank” warning light will turn on. If this is the
case, press the “Start/Pause/Cancel” button
to resume the drying cycle after draining the
water tank.
To drain the water tank:
1. Drain the water as shown on the picturre .
2. Unlock the 2 condenser locks after opening
the kick plate.
3. Pull out the condenser.
2. If there is lint accumulation in the water tank
cover, clean it and press to close.
4. Clean the condenser by applying
pressurized water with a shower head and
wait until the water drains.
3. Place the water tank into its seat.
For the condenser
Hot and humid air in the condenser is cooled
with the cold air from the room. Thus, the
humid air circulating in your dryer is condensed
and then pumped into the tank.
CClean the condenser after every 30 drying
cycles or once a month.
To clean the condenser:
1. If a drying process has been carried out,
open the door of the machine and wait until
it cools down.
21 EN
5. Place the condenser in its housing. Fasten
the 2 locks and make sure that they are
seated securely.
6. Close the kick plate cover.
22 EN
8 Suggested solutions for problems
Drying process takes too much time
• Meshes of the filter may be clogged. Wash with water
Laundry comes out wet at the end of drying.
• Meshes of the filter may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not load the dryer in excess.
Dryer does not switch on or the programme does not start. Dryer is not activated when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Programme might have not been set or the «Start/Pause/Cancel» button might have not
been pressed. Make sure that the programme has been set and it is not in “Pause” mode.
• «Childproof lock» might have been activated. Deactivate the childproof lock.
Programme has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the programme.
• Make sure that the condenser cover and the red lock is closed securely.
Laundry has shrunk, become felted or deteriorated.
• A programme suitable for the laundry type might have not been used. Dry only the laundry
which is suitable for drying in dryer after checking the labels on your clothes.
• Select a programme with suitable low temperature for the laundry type to dry your clothes.
Drum lightning does not come on. (For models with lamp)
• Dryer might have not been started by using the «On/Off» button. Make sure that the dryer is
on.
• Bulb may have blown. Call the authorized service to replace the bulb.
“Final / Anti-creasing” LED flashes.
• The 2-hour anti creasing programme to prevent laundry from creasing might have been
activated. Turn off the dryer and take out the laundry.
“Final / Anti-creasing” LED is on.
• Programme has come to an end. Turn off the dryer and take out the laundry.
The “Drying” LED flashes.
• A heat sensor failure has occurred. Dryer ends the programme without heating. Turn off the
dryer and take out the laundry. Call your authorized service
• “Filter cleaning” LED is on.
• Filter might have not been cleaned. Clean the cover filter.
“Water comes out the cover”
• Clean the entire inner surface of the cover and door gasket.
“Cover opens spontaneously.”
• Push it until you hear that it is closed.
For products with a condenser:
“Water tank” warning LED is on.
• Water may be full. Drain the water in the tank.
“Condenser cleaning” LED is on.
• Condenser might have not been cleaned. Clean the filters in the condenser under the kick
plate.
A Call an authorized service if the problem persists.
23 EN
9 Guarantee
Important notes
Your new product is guaranteed against the
cost of breakdown repairs for twelve months
from the date of the original purchase.
What is covered?
• Repairs necessary as a result of faulty
materials, defective components or
manufacturing defect.
• The cost of functional replacement parts,
but excluding consumable items.
• The labour costs of a approved repairer to
carry out the repair.
What is not covered?
• Transit, delivery or accidental damage or
misuse and abuse.
• Cabinet or appearance parts, including
knobs, flaps, handles or container lids.
• Accessories or consumable items including
but not limited to, ice trays, scrapers,
cutlery baskets, filters and light bulbs.
• Repairs required as a result of
unauthorised repair or inexpert installation
that fails to meet the requirements
contained in the user instruction book.
• Repairs to products used on commercial
or non-residential household premises.
• Loss of frozen food in freezers or fridge/
freezers. (Food loss insurance is often
included within your household contents
insurance policy, or may be available
separately from your retailer).
• Your product is designed and built for
domestic household use only.
• The guarantee will be void if the product
is installed or used in commercial or nonresidential domestic household premises.
• The product must be correctly installed,
located and operated in accordance with
the instructions contained in the User
Instructions Booklet provided.
• Professional installation by a qualified
Electrical Domestic Appliance Installer
is recommended for all Washing
Machines,Tumble Dryers, Dishwashers,
Dryers and Electric Cookers
• Gas Cookers must only be installed by a
Gas safe registered Gas Installer.
• The guarantee is given only within the
boundaries of the United Kingdom and the
Republic of Ireland.
• The guarantee is applicable only to new
products and is not transferable if the
product is resold.
• Disclaims any liability for incidental or
consequential damages.
• The guarantee does not in anyway diminish
your statutory or legal rights.
24 EN
10 Service
Please keep your purchase receipt or other
proof of purchase in a safe place; you will
need to have it should the product require
attention under guarantee.
You should also complete the details below;
it will help us assist you when requesting
service. (The model number is printed on the
Instruction Booklet and the serial number
is printed on the Rating Label affixed to the
appliance)
Service once the manufacturers
guarantee has expired.
If you have purchased an extended guarantee
please refer to the instructions contained
within the extended guarantee agreement
document. Otherwise please call the
appropriate number above where service can
be obtained at a charge.
Should you experience any difficulty in
obtaining service please contact the Customer
Help-Line.
Tel: 0845 600 4911
For service under guarantee simply telephone
the appropriate number below.
Model No:
Serial No:
Retailer:
Date of purchase:
Republic of Ireland
UK Mainland & Northern Ireland
All Refrigeration, 01 862 3411
All Cookers
Washing Machines & Dryers, Tumble Dryers
Dishwashers
Before requesting service please check the
trouble-shooting guide in the Operating
Instructions as a charge may be levied where
no fault is found even though your product
may still be under guarantee.
Fridges & Freezers 0845 600 4903
Electric Cookers 0845 600 4902
Gas & Dual Fuel Cookers
0845 600 4905
Washing Machines & Tumble Dryers
0845 600 4906
25 EN