- Industrial & lab equipment
- Electrical equipment & supplies
- Electrical distribution
- Wall transmitters
- User manual
advertisement
Plug-In ON/OFF Control (In/Outdoor)
Model PA-318
1. INTRODUCTION 3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS (CONT)
(In /Outdoor), Model PA-318. This receiver module allows you to wirelessly turn on and off lights or small appliances with the SkylinkHome TM transmitters.
The Plug-In ON/OFF Control (In /Outdoor) PA-318 can communicate with up to 8 transmitters, so user has the option to add more transmitters to the system, such as more remote controls, or motion sensors etc.
Operating Mode
On / Off
Countdown Timer
LED Indication
Flashing
Steadily On based on rolling code technology to ensure highest security is used.
The following items are included in this package:
- Plug-In ON/OFF Control (In /Outdoor)
- Antenna
- User's Instructions
Plug-In ON/OFF Control
(In /Outdoor)
2. SETUP
Insert the antenna to the Plug-In ON/OFF Control
(In/Outdoor) as shown. Place the antenna in the upright position to have the best reception.
Simply plug the Plug-In ON/OFF Control (In/Outdoor) to an electrical outlet, then plug in a light or home appliance to the socket on the Plug-In ON/OFF
Control (In/Outdoor).
The Plug-In ON/OFF Control (In/Outdoor) is designed to operate maximum load of 1500W at 120VAC.
Do not connect loading that exceeds this maximum rating.
Antenna
5. Within 15 seconds, follow steps A) to C).
A). Press the PROG button on the back of the
TC transmitter with a sharp object.
B). Press the button on the TC transmitter that
you would like to program.
C). Once the transmitter is programmed, the
red LED on the module flashes quickly then
stops flashing, indicating you have successfully
programmed the transmitter to the module.
Now the programmed transmitter button is
ready to be used for ON/OFF Mode.
“PROG” button
TC-318-3
Press the desired button
To program a TC series transmitter into the Plug-In ON/OFF Control
(In/Outdoor) under Countdown Timer Mode, follow the instructions below.
1. Plug in a load to the Plug-In Module (Indoor / Outdoor)
2. Plug in the module to an AC electrical outlet, the red LED flashes once
quickly. The connected load (i.e. light) should be in off mode.
3. Press and hold the "SET" button for about 9 seconds, until the red LED
is steadily on.
4. You may now release the "SET" button. The red LED will continue to be
on for about 15 seconds.
5. Within 15 seconds, follow steps A) to C).
A). Press the PROG button on the back of the TC transmitter with a
sharp object.
B). Press the button on the TC transmitter that you would like to program.
C). Once the transmitter is programmed, the red LED on the module
flashes quickly then stops flashing, indicating you have successfully
programmed the transmitter to the module. Now the programmed
transmitter button is ready to be used for Countdown Timer Mode.
3. PROGRAMMING TRANSMITTERS (TC SERIES)
In order to operate the Plug-In ON/OFF Control (In/Outdoor) remotely, transmitter or sensor, must be programmed to the Plug-In ON/OFF
Control(In /Outdoor). Each module can be operated by up to 8 different transmitters (or 8 different command signals).
There are 2 operating modes with the Plug-In ON/OFF Control (In/Outdoor):
1) On / Off Mode - When a valid signal is received, it will turn on or off a
load.
2) Countdown Timer Mode - When a valid signal is received, the load will
be on for a specific period of time, either 1 minute, 5 minutes, 15 minutes,
30 minutes, or 60 minutes, then off. This is mainly for energy saving.
To program a TC series transmitter into the
Plug-In ON/OFF Control (In/Outdoor) under
ON/OFF mode, follow the instructions below.
1. Plug in a load to the Plug-In Module
(Indoor / Outdoor)
2. Plug in the module to an AC electrical
outlet, the red LED flashes once quickly.
The connected load (i.e. light) should be
in off mode.
3. Press and hold the “SET” button for about
3 seconds, unit the red LED flashes.
4. You may now release the “SET” button.
The red LED will continue to flash for
about 15 seconds.
2
3 Light Off
Note: To program other transmitters/sensors (besides TC transmitter), please refer to the instructions of the transmitters/sensors and the above instructions.
Note: You must complete the programming sequence within the
15-second interval, otherwise, the module will quit from programming mode and you need to start again from step 3 if the red LED is off.
4. SET TIMER DURATION
As mentioned, the timer can be set to the following durations, 1 minute,
5 minutes, 15 minutes, 30 minutes, or 60 minutes.
There is only one timer setting, so all transmitters that are programmed for timer mode will have the same timer duration. To set the timer duration, follow the instructions below:
1. Plug in the module to an AC outlet, the red LED flashes once, so it is
powered on properly.
2. Turn on the connected load by a programmed transmitter. The load
must be on under ON/OFF mode in order to set the timer duration.
3. Press and hold the SET button for 3 seconds, the red LED flashes
once. The number of flashes indicates the timer duration:
Number of Flashes
1
4
5
2
3
Timer Duration
1 min.
5 min.
15 min.
30 min.
60 min.
1
Red LED
LED Flashing: On/Off Mode
LED Steadily ON: Timer Mode
4. Continue to hold the SET button until it reaches the desired setting. The
status will change every 6 seconds, i.e. hold the SET button, you will
see the number of flashes changes from 1 to 2, 2 to 3, etc.
4. SET TIMER DURATION (CONT)
Note: Once the number of flashes reaches 5, it will stay at this setting. If you would like to go back to other settings, such as 1 flash, release the button and repeat from step 1 to start over.
Once a transmitter (button) is programmed for timer mode, activating this programmed transmitter (button) will turn on the light for the specified timer duration.
During a timer count down, if the module receives another signal for timer operation, the timer will start again and overrides the previous timer, therefore, extending the On period by another timer interval.
To stop timer count down, press a programmed button for ON/OFF mode.
8. ERASING TRANSMITTERS FROM THE MODULE
You may erase a transmitter or sensor from the module, but you cannot erase a specific device directly, you must erase all the wireless devices, then program the ones you want to keep. Follow the instructions below to erase programmed transmitters / sensors.
1. Power off the Plug-In Module (Indoor / Outdoor)
by removing it from the AC socket.
2. Press and hold the SET button, while plugging in
the module to an AC outlet.
3. The red LED will be on first, then flashes rapidly
for 1 second, then on and off.
4. You may release the SET button, now
you have successfully erased all the
devices from the lighting receiver.
Press and hold the SET button while plugging it in to an AC socket
5. Now you have successfully erased all
the devices.
5. ON / OFF OPERATION
The PA-318 Plug-In Module (Indoor / Outdoor) allows on / off operation.
When the programmed button is pressed, it will transmit a signal to toggle the status of a load. For example, if a toggle signal is received when the light is off, that signal will turn on the light.
If you have a deluxe remote, you can make sure that you will actually turn on a light by pressing [ ] first, then the programmed button. Similarly, you can make sure that you will turn off a light by pressing [ ] first, then the programmed button.
If you have a deluxe remote and you press [ ], all those receivers to which the remote is programmed will turn on their loads. If you press
[ ], all those receivers to which the remote is programmed will turn off their loads.
9. TECHNICAL SPECIFICATIONS
Input Voltage: 120V AC, 60Hz
Standby Current: 3mA
Minimum Load: 10W
Maximum Rating: 15 Amps
Maximum Load: 1500W at 120VAC
Operating Frequency: 318MHz
Operational Temperature: -4° F - 140° F (-20° C - 60° C)
Humidity: 5%-95%
Range: Up to 500 feet in open area.
6. COUNTDOWN TIMER OPERATING MODE
If a transmitter or a sensor is programmed to the Plug-In ON/OFF Control
(In/Outdoor) under the countdown timer mode, when that transmitter is activated, the load connected will be on for the predetermined timer interval, the LED on the Plug-In ON/OFF Control will also be on. After the timer interval, the load will be turned off.
Pressing a programmed button for ON/OFF mode can override timer operation.
10. FCC
The device is approved by the FCC and it complies with Part 15 of the FCC Rules.
Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment.
7. ZONE OPERATION
An optional deluxe remote is needed for zone operation. A Zone Command allows you to operate multiple lights altogether in the same zone.
A zone command must first be programmed to the receiver before zone operation. To program a zone command, please refer to the user's instructions of the deluxe remote.
Zone Operation - On / Off
To turn on or off a zone, hold [ ] or [ ] until the red LED flashes three times and keeps on, then release the held button and press the zone number.
For example:
Hold [ ] until the red LED flashes three times and keeps on, then release [ ] and press [1], all lights in zone 1 will be turned on.
Hold [ ] until the red LED flashes three times and keeps on, then release [ ] and press [1], all lights in zone 1 will be turned off.
Note: The Zone Operation is also applicable to loads other than lights.
11. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
12. CUSTOMER SERVICE
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
13. ACCESSORIES
The Skylink Home TM System consists of many other devices such as
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
TM ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z700
Patent Pending
©2010 SKYLINK GROUP
V1.8
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project