96901K-MN - RT Edwards Commercial

96901K-MN
Ceramic glass hob
Table de cuisson vitrocéramique
Glaskeramische kookplaat
Installation and Operating Instructions
Instructions de montage et mode d’emploi
Montage- en gebruiksaanwijzing
Dear Customer,
Please read these user instructions carefully and keep them to refer to
later.
Please pass the user instructions on to any future owner of the appliance.
1
3
2
2
The following symbols are used in the text:
Safety instructions
Warning! Information that affects your personal safety.
Important! Information that prevents damage to the appliance.
Useful tips and hints
Environmental information
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooking surface layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch Control sensor fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Residual heat indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
6
7
7
8
Operating the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching the appliance on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the heat setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching the outside ring on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching the STOP+GO function on and off. . . . . . . . . . . . . . . . . . . . . . . . .
Locking/unlocking the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the automatic warm-up function . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the child safety device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety cut-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
8
9
9
10
10
12
13
16
17
Tips on Cooking and Frying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cookware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Energy saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Examples of cooking applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
18
18
19
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Guarantee/Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
Service
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
3
Operating Instructions
1 Safety instructions
3
5
Please comply with these instructions. If you do not, any damage resulting is not covered by the warranty.
This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Correct use
• This appliance should be used only for normal domestic cooking and
frying of food.
• The appliance must not be used as a work surface or as a storage surface.
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids, highly inflammable materials
or fusible objects (e.g. plastic film, plastic, aluminium) on or near the
appliance.
Children’s safety
• Small children must be kept away from the appliance.
• Only let bigger children work on the appliance under supervision.
• To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device.
General safety
• The appliance may only be installed and connected by trained, registered service engineers.
• Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards.
• In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off
and disconnected from the electrical supply, to prevent the possibility
of an electric shock.
• Repairs to the appliance must only be carried out by trained registered service engineers.
4
Safety during use
• Overheated fats and oils can ignite quickly. When cooking with fat or
oil (e.g. chips) do not leave the appliance unattended.
• There is the risk of burns from the appliance if used carelessly.
• Remove stickers and film from the glass ceramic.
• Cables from electrical appliances must not touch the hot surface of
the appliance or hot cookware.
• Switch the cooking zones off after each use.
Safety when cleaning
• For cleaning, the appliance must be switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or
high-pressure cleaning equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by objects falling onto it.
• The edge of the glass ceramic can be damaged by being knocked by
the cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the glass ceramic if pushed across the surface.
• Objects that melt and things that boil over can burn onto the glass
ceramic and should be removed straightaway.
• To avoid damaging cookware and glass ceramics, do not allow saucepans or frying pans to boil dry.
• Do not use the cooking zones with empty cookware or without cookware.
5
Description of the Appliance
Cooking surface layout
Single cooking zone
1200W
Triple ring cooking zone
1050/1950/2700W
Multi-purpose zone
1400/2200W
Single cooking zone
1800W
Single cooking zone
1800W
Control panel
Control panel layout
.................
On/Off
with power indicator
Display
Cooking zone indicators Heat setting selection
Timer function
Outside/middle ring
Timer display
On/Off
STOP+GO
Triple ring pilot light
6
Double ring
pilot light
Lock
Outside
ring
On/Off
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions
are controlled by touching sensor fields and confirmed by displays and
acoustic signals.
Touch the sensor fields from above, without covering other sensor
fields.
Sensor field
TIMER
Function
On / Off
To switch the appliance on and off
Increase settings
Increasing heat setting/time
Decrease settings
Decreasing heat setting/time
Timer
Timer selection
Lock
Locking/unlocking the control panel
Stop+Go
To switch the Keep Warm setting on/
off
Triple ring switch
To switch outer rings
on and off
Multi-purpose zone To switch the outside ring on and off
switch
Displays
Display
¾
u
Description
Cooking zone is switched off
Keep warm setting
Keep warm setting/STOP+GO function is set
¿ - Ç Heat settings
Heat setting is set
2 - 6 Heating setting plus
Intermediate heat setting is set
decimal point
a
Automatic warm up
function
Automatic warm-up function is activated
e
Fault
Malfunction has occurred
h
Residual heat
Cooking zone is still hot
l
Child safety device
Lock/child safety device is engaged
_
Safety cut-out
Safety cut-out has been activated
7
Residual heat indicator
1
3
Warning! Risk of burns from residual heat. After being switched off,
the cooking zones need some time to cool down. Look at the residual
heat indicator h .
Residual heat can be used for melting and keeping food warm.
Operating the appliance
Switching the appliance on and off
Control panel
3
Display
Switch on
Touch
for 2 seconds ¾ / h
Switch off
Touch
for 1 second
h / none
Pilot light
lights up
goes out
After switching on, within approx. 10 seconds a heat setting or a function must be set, otherwise the appliance automatically switches itself
off.
Setting the heat setting
3
8
Control panel
Indicator
To increase
Touch
u to Ç
To decrease
Touch
Ç to ¾
To switch off
Touch
and
at the same time
¾
The keep warm setting u lies between ¾ and ¿. It is used to keep
food warm.
Switching the outside ring on and off
3
By switching the outside rings on or off, the effective heating surface
can be matched to the size of the cookware.
Before an outside ring can be switched on, the inside ring must be
switched on.
Triple cooking zone
Sensor panel
Power indicator
To switch on middle ring
Touch
for 1-2 seconds.
One power indicator is lit.
To switch on outside ring
Touch
for 1-2 seconds.
Two power indicators are
lit.
To switch off outside ring
Touch
for 1-2 seconds.
Second power indicator
goes out.
To switch off middle ring
Touch
for 1-2 seconds.
First power indicator goes
out.
Roasting zone
To switch on outside ring
Sensor panel
Touch
To switch off outside ring Touch
Power indicator
for 1-2 seconds
for 1-2 seconds
is lit
goes out
Switching the STOP+GO function on and off
The STOP+GO function simultaneously switches all cooking zones that
are switched on to the keep warm setting and then back to the heat
setting that was previously set. This function can be used to briefly interrupt and then continue the cooking process e.g. to take a telephone
call.
3
3
Control panel
Display
To switch
on
Touch STOP+GO
u
To switch
off
Touch STOP+GO
heat setting that was previously set (not automatic
warm up function)
Timer functions are not stopped by STOP+GO.
STOP+GO locks the whole control panel except the sensor field
.
9
Locking/unlocking the control panel
The control panel, with the exception of the “On/Off” sensor field, can
be locked at any time in order to prevent the settings being changed
e.g. by wiping over the panel with a cloth.
3
Control panel
Display
Switch on
Touch
l (for 5 seconds)
Switch off
Touch
previously set heat setting
When you switch the appliance off, the locking function is automatically switched off.
Using the automatic warm-up function
All cooking zones are equpped with an automatic warm up function
When setting a heat setting using , when starting from ¾, the cooking zone switches to full power for a certain amount of time and then
automatically switches back to the heat setting set.
Control
panel
3
3
10
possible
heat settings
Display
Switch on
Touch
(only when starting at
¾)
¿ to Æ
a (after 5 seconds)
Switch off
Touch
Æ to ¿ / u Æ to u
Not used
Touch
Ç to u
Ç to u
If during the automatic warm up a a higher heat setting is selected,
e.g. from Á to Ã, the automatic warm up is adjusted.
If there is still residual heat on the cooking zone (display h), the automatic warm up is not performed.
The length of time that the automatic warm up function operates depends on the heat setting selected.
Heat
setting
Length of the
automatic warm up
[min:sec]
Intermedi- Length of the
ate heat
automatic warm up
setting
[min:sec]
v
0:30
1
1:00
2
1:40
2.
2:40
3
4:50
3.
5:30
4
6:30
4.
8:10
5
10:10
5.
12:20
6
2:00
6.
2:30
7
3:30
8
4:30
9
---
11
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Setting the child safety device
Step
Control panel
1.
Switch on the appliance
(Do not set a heat setting)
2.
Touch
3.
Touch
Display/Signal
¾
until the signal sounds Acoustic signal
l
Appliance switches off. The child safety device is engaged.
Releasing the child safety device
Step
1.
Control panel
Switch on the appliance
2.
Touch
3.
Touch
Display/Signal
l
until the signal sounds Acoustic signal
Appliance switches off. The child safety device is released.
Overriding the child safety device
The child safety device can be released in this way for a single cooking
session; it remains activated afterwards.
Step
1.
2.
Control panel
Switch on the appliance
Touch
and
Display/Signal
l
at the same time ¾ / acoustic signal
Until the appliance is next switched off, it can used as normal.
12
Using the timer
All cooking zones can use each use one of the two timer functions at
the same time.
3
3
Function
Condition
Outcome after the
time has elapsed
Automatic cut-out
a heat setting is set
acoustic signal
00 flashes
Cooking zone
switches off
Countdown timer
cooking zones not in use
acoustic signal
00 flashes
If a cooking zone is switched off, the timer function set is also switched
off.
If a heat setting is set on this cooking zone in addition to a countdown
timer, the cooking zone is switched off after the time set has elapsed.
Selecting a cooking zone
Step
Control panel
Indicator
1.
Touch TIMER 1x
Pilot light for the first
cooking zone flashes
2.
Touch TIMER 1x
Pilot light for the second cooking zone flashes
3.
Touch TIMER 1x
Pilot light for the third
cooking zone flashes
4.
Touch TIMER 1x
Pilot light for the
fourth cooking zone
flashes
5.
Touch TIMER 1x
Pilot light for the fifth
cooking zone flashes
13
3
3
3
The heat setting indicator of the selected cooking zone goes out, until
the timer time is set.
If the power indicator is flashing more slowly, the heat setting indicator
appears again and the heat setting can be re-set or modified.
If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes.
Setting the time
Step
Control panel field
Display
1.
TIMER Select cooking zone
Pilot light of the cooking zone selected flashes
2.
Touch
or for
00 to 99 minutes
the cooking zone selected
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Switching off the timer function
Step
Control panel field
Display
1.
TIMER Select cooking zone
Pilot light of the cooking zone selected flashes faster
The time remaining is displayed
2.
Touch
for the
The time remaining counts down to
cooking zone select- 00.
ed
The pilot light goes out.
The timer function for the selected cooking zone is switched off.
14
Changing the time
Step
Control panel field
Display
1.
TIMER Select cooking zone
Pilot light of the cooking zone selected flashes faster
The time remaining is displayed
2.
Touch
or
for
01 to 99 minutes
the cooking zone selected
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Displaying the time remaining for a cooking zone
Step
Control panel field
Display
1.
TIMER Select cooking Pilot light of the cooking zone selectzone
ed flashes faster
The time remaining is displayed
After a few seconds the pilot light flashes more slowly.
Switching off the acoustic signal
Step
Control panel field
Acoustic signal
1.
Touch TIMER
Acoustic signal to acknowledge.
Acoustic signal stops.
15
Safety cut-out
Cooking surface
• If after switching on the cooking surface, a heat setting is not set for
a cooking zone within approx. 10 seconds, the cooking surface automatically switches itself off.
• If one or more sensor fields are covered for longer than approx. 10
seconds, e.g. by a pan placed upon it, a signal sounds and the cooking
surface switches off automatically.
• If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds.
Control panel
• When the appliance is switched off, if one or more of the sensor
fields on the control panel are covered for more that 10 seconds, an
acoustic signal sounds. The acoustic signal switches itself off automatically when the sensor fields are no longer covered.
Cooking zones
• If one of the cooking zones is not switched off after a certain time, or
if the heat setting is not modified, the relevant cooking zone switches
off automatically.
16
Heat setting
Switches off after
V, 1 - 2
6 hours
3-4
5 hours
5
4 hours
6-9
1.5 hours
Power-Management
The three cooking zones front left,
front right and back right together
have a maximum possible power
available to them.
If it looks like the maximum power
of all three cooking zones is going
to be exceeded, for example by
turning on an additional cooking
zone or by turning up a heat setting, the Power Management automatically reduces the power of another cooking zone. The power of the
cooking zone that has been switched on for the longest time is reduced. For two minutes the indicator for this cooking zone changes between the previously set heat setting and the maximum possible heat
setting at this time. After two minutes the actual heat setting is displayed.
The following table shows the distribution of the maximum possible
heat settings when all three cooking zones are on at the same time.
1st cooking zone
2nd cooking zone
1 - 6
8
9
7
7
9
8
8
8
17
Tips on Cooking and Frying
3
Information on acrylamides
According to the latest scientific knowledge, intensive browning of
food, especially in products containing starch, can constitute a health
risk due to acrylamides. Therefore we recommend cooking at the lowest
possible temperatures and not browning foods too much.
Cookware
• You can recognise good cookware from the bottoms of the pans. The
bottom should be as thick and flat as possible.
• Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the glass ceramic surface which are
difficult or impossible to remove.
Energy saving
2
2
2
2
18
Always place cookware on the cooking zone before it is switched on.
If possible, always place lids on the
pans.
Switch cooking zones off before the
end of the cooking time, to take advantage of residual heat.
Bottom of pans and cooking zones
should be the same size.
Examples of cooking applications
The information given in the following table is for guidance only.
Heat
setting
Cookingprocess
0
V
suitable for
Cooking
time
Tips/Hints
Off position
Keeping
food
warm
Keeping cooked foods
warm
as required
Cover
Melting
Hollandaise sauce,
melting butter, chocolate,
gelatine
5-25 mins.
Stir occasionally
Solidifying
Fluffy omelettes, baked
eggs
10-40 mins.
Cook with lid on
1-2
Simmering rice and milkAdd at least twice as
based dishes
much liquid as rice, stir
25-50 mins.
Heating up ready-cooked
milk dishes part way
meals
through cooking
2-3
Simmering on
low heat
3-4
Steaming Steaming vegetables, fish
20-45 mins.
Braising
braising meat
4-5
With vegetables add
only a little liquid (a
few tablespoons)
Steaming potatoes
20-60 mins.
Use only a little liquid,
e. g.: max. ¼ l water
for 750 g potatoes
Cooking larger quantities
of food, stews and soups
60-150
mins.
Up to 3 l liquid plus ingredients
Steady
frying
Turn halfway through
cooking
5-15 mins.
per pan
Turn halfway through
cooking
Boiling
6-7
Gentle
Frying
Frying escalopes, veal
cordon bleu, cutlets, rissoles, sausages, liver, roux,
eggs, pancakes, doughnuts
7-8
Heavy
Frying
Hash browns, loin steaks,
steaks, Flädle (pancakes
for garnishing soup)
9
Boiling
Searing
Deep
frying
Boiling large quantities of water, cooking pasta, searing meat
(goulash, pot roast), deep frying chips
19
Cleaning and Care
1
1
1
Take care! Risk of burns from residual heat.
Warning! Sharp objects and abrasive cleaning materials will damage
the appliance. Clean with water and washing up liquid.
Warning! Residues from cleaning agents will damage the appliance.
Remove residues with water and washing up liquid.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth and a little washing up liquid.
2. Rub the appliance dry using a clean cloth.
Removing deposits
1. Place a scraper on the glass ceramic surface at an angle.
2. Remove residues by sliding the blade over the surface.
3. Wipe the appliance with a damp cloth and a little washing up liquid.
4. Rub the appliance dry using a clean cloth.
Remove
Type of dirt
imme- when the appliance has
diately
cooled down
sugar, food containing sugar
yes
---
plastics, tin foil
yes
---
limescale and water rings
---
yes
fat splashes
---
yes
shiny metallic discolorations
---
yes
using
a scraper*
cleaner for glass ceramic or stainless
steel*
*Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops
3
3
20
Remove stubborn residues with a cleaner for glass ceramic or stainless
steel.
Scratches or dark stains on the glass ceramic that cannot be removed
do not however affect the functioning of the appliance.
What to do if …
Problem
The cooking zones will not
switch on or are not functioning
Possible cause
Remedy
More than 10 seconds have Switch the appliance on
passed since the appliance again.
was switched on
The child safety device is
switched on l
Deactivate the child safety
device (See the section
“Child safety device”)
Several sensor fields were
touched at the same time
Only touch one sensor field
Safety cut-out has been
triggered
Remove any objects (pan,
cloths, etc.) that are lying
on the control panel.
Switch the appliance on
again
STOP+GO is activated u
Switching off STOP+GO
Acoustic signal sounds
The control panel is wholly Remove objects.
when appliance is switched or partly covered by oboff
jects.
The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call the
therefore not hot
Customer Service Department.
The automatic warm up
function is not switching
itself on
There is still residual heat
on the cooking zone h
Let the cooking zone cool
down
The highest heat setting is
set Ç
The highest heat setting
has the same power as the
automatic warm up function
The heat setting was set
using the sensor field
1. Switching off the cooking zone
2 . Set the cooking zone using the sensor field
Acoustic signal sounds and The On/Off sensor field has Do not place any objects
appliance switches itself on been covered up, e.g. by a on the control panel
and then off again; after 5 cloth
seconds another acoustic
signal sounds
Display changes between
two heat settings
Power Management is reducing the power of this
cooking zone
See section “Power Management“ in the Operating
the Appliance chapter
21
Problem
Possible cause
Remedy
_ is lit
Overheating protection for Switch off the cooking
the cooking zone has been zone. Switch the cooking
triggered
zone on again
e and number are dis-
Electronics fault
played
Disconnect the appliance
from the electrical supply
for a few minutes (Take the
fuse out of the house’s wiring system)
If after switching on again,
e is displayed again, call
the customer service department
e and minus are displayed Light rays that are too
Briefly shade the control
strong on the control pan- panel, for example with
el, for example bright sun- the hand Acoustic signal
light
sounds, appliance switches
itself off Switch appliance
on (again)
1
3
22
If you are unable to remedy the problem by following the above
suggestions, please contact your dealer or the Customer Care Department.
Warning! Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from
improper repairs.
If the appliance has been wrongly operated, the visit from the customer
service technician or dealer may not take place free of charge, even
during the warranty period.
Disposal
2
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste disposal facilities.
Old appliance
W
The symbol
on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you
purchased the product.
23
Installation Instructions
Safety instructions
1
1
24
The laws, ordinances, directives and standards in force in the country of
use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)
Installation may only be carried out by a qualified electrician.
The minimum distances to other appliances and units are to be observed.
A protective floor must be installed under the appliance.
The cut surfaces of the worktop are to be protected against moisture
using a suitable sealant.
The sealant seals the appliance to the work top with no gap.
Do not use silicon sealant between the appliance and the work top.
Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened.
WARNING!
Risk of injury from electrical current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of voltage.
• Observe connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection through correct installation by a qualified electrician.
• The appliance must be connected to the electrical supply by a qualified electrician.
IMPORTANT!
Risk of injury from electrical current.
Loose and inappropriate plug and socket connections can make the terminal overheat.
• Have the clamping joints correctedly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90° (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a
special cable (type H05BB-F Tmax 90°; or higher). The latter is available from the Customer Care Department.
A device must be provided in the electrical installation which allows the
appliance to be disconnected from the mains at all poles with a contact
opening width of at least 3 mm.
Suitable isolation devices include line protecting cut-outs, fuses (screw
type fuses are to be removed from the holder), earth leakage trips and
contactors.
25
Guarantee/Customer Service
Weitere Kundendienststellen im Ausland
In diesen Ländern gelten die Garantiebedingungen der örtlichen Partner. Diese können dort eingesehen werden.
Further after-sales service agencies overseas
In these countries our AEG-Electrolux agents’ own guarantee conditions are applicable. Please obtain further details direct.
Autres agences étrangères assurant le service après-vente
Dans ces pays, les conditions de garantie des concessionnaires de la région sont valables. Vous pouvez les consulter sur place.
Otros puntos de Postventa en el extranjero
En estos países rigen las condiciones de nuestros representantes locales.
las cuales pueden ser consultadas allí mismo.
Ulteriori uffici del servizio tecnico assistenza clienti all’estero
In questi paesi sono valide le condizioni di garanzia dei partner locali.
Queste condizioni possono essere esaminante sul luogo.
Serviços de assistência técnica no estrangeiro
Nestes países são válidas as condições de garantia dos concessionários
locais, podendo aí ser consultadas.
További vevöszolgálati irodák külföldön
Ezekben az országokban a mi AEG-Electrolux vevöszolgálatainknál
saját jótállási feltételek alkalmazhatók. A további adatokat kérjük
közvetlenül szerezzék be.
Servisne službe
Na garancijskem listu boste našli seznam pooblašèenih servisnih
služb AEG-Electrolux.
26
U.A.E. Abu Dhabi
Universal Trading Company
P.O. Box 43 99
Tel.: 6335331
Service Center 6733974
Jordan
Jordan Household
Supply Co. Ltd.
P.O. Box 3/68
Amman/Tel.: 69 70 50
Malta
ITC
International Trading Company
White House Building
Mountbatte Street
Blata L-Bajda/Tel.: 220644
Egypt
Middle East Commercial
Center
4 Salah El Dein St. - 2nd floor
Heliopolis, Kairo
Egypt
Tel.: 2024181719
Canada
EURO-LINE Appliances
2150 Winston PARK Drive 20
Oakville, Ontario L6H 5V1
Tel.: 905 829 3980
Fax: 905 829 3985
Mauritius
Happy World Centre Ltd.
P.O. 7 54
1 Chausee Street
Port Louis
Tel.: 25355
Australia
The Andi-Co Group
1 Stamford Road
Oakleigh VIC 3166
Tel.: (03) 9569 1255
Fax: (03) 9569 1450
www.andico.com.au
Korea (South)
Core Incorp.
3/F Chewoo Bldg.
200 Nonhyun-Dong
Kangnam-Ku 135-010
Seoul
Telefon 82 2 549 89 61
Namibia
AEG NAMIBIA (PTY)
LIMITED-Jeppe Street
Northern Industrial Area
Windhoek
Tel.: (061) 21-6082/4
Fax: (061) 217838
Bahrain/Arabian Gulf
A.A. Zayani & Sons
P.O. Box 9 32
Bahrain
Tel.: 17311124
Croatia
Electrolux D.O.O.
Suplova 7
10000 Zagreb
Tel.: 1 61 19512
Fax: 1 61 19513
New Zealand
Monaco Corporation Ltd.
10 Rothwell Avenue
Albany - Auckland
4399 Auckland 1
New Zealand
Tel.: 00 64-92 59 11 11
Fax: 00 64-92 59 11 12
Bulgaria
Electrolux Bulgaria E.O.O.D.
91 Levski Blvd.
1000 Sofia
Tel.: 2 806676
Fax. 2 980 5276
Kuwait/Arabian Gulf
Ali Al-Ghanim Est.
P.O. Box 21540 - Safat
Tel.: 4822190
Fax: 4820116
Syria
WATTAR CO.
P.O. Box 36109
Mazzeh - Damascus
Direct Phone: 00963116132649
Fax: 00963116119537
Cyprus
Hadjikyrlakos & Sons Ltd.
Prodromou 121
P.O. Box 21587
Nicosia 1511
Service Telephones:
Nicosia 02 481226
Limassol 05 562182
Larnaca 04 633929
Paphos 06 932 699
Lebanon
Adib & Assaferi
P.O. Box 539
Tripoli
Iran
ARIAN International Development Co.
AEG Showroom
Shariati, Balatar as Safar
Teheran / Iran
Phone No. Showroom:
021 / 285 513 / 4
Phone No. Service:
021 / 312 27 67 / 8
Estonia
Electrolux Estonia Ltd.
Mustamäe tee 24
EE0006 Tallinn
Tel.: (372) 6 650 090
Fax: (372) 6 650 092
Latvia
Electrolux Latvija Ltd.
Kr.Barona iela 130/2
Riga, LV-1012
Tel.: 371 7313626
Fax: 371 7845954
Poland
Electrolux Poland Sp. zo.o.
ul. Domaniewska 41
02-034 Warszawa
tel.: 022 874 33 33
fax: 022 874 33 00
Hong Kong
Dah Chong Hong Ltd.
20 Kai Cheung Road
Kowloon Bay
Kowloon - Hong Kong
Tel.: 0085222621620
Fax: 0085227550333
Lithuania
Electrolux Lithuania
Verkui 29
2600 Vilnus
Tel.: 372 272 3326
Fax: 372 272 3366
Russia
Electrolux Russia Ltd.
16 Olympiysky prospekt
129090 Moscow
Tel.: (095) 937 7837
Fax: (095) 926 5513
27
28
Israel
Evis Ltd.
Tadiran-Ampa Service
10 Gibonay Israel Street
New Industrial Zone
Netanya, 42504
Israel
Malaysia
Arzbergh Engineering
No. 49A/B, Jalan Petaling
Utama 7
4600 Petaling Jaya
Tel.: 3 795 1084
Fax: 3 795 1082
Saudi Arabia
Awad Badi Nahas Est
Shara Siteen
Jeddah 21463
Phone: 6646583
Alia Trading Co
Mecca Road
Riyadh 11491
Phone 4645977
Japan
Electrolux Japan Ltd.
Domestic Appliances
Department
Maruzen Showa Warehouse
Building
Tookai 4-5-12, Ota-ku
143-006 Tokyo
Tel.: 0120-13-7117
Fax: 03-3790-5257
Singapore
Group Pte Ltd.
833 Bukit Timah Road
Unit no. 01-11 Royalville
279887 Singapore
Tel.: 0065 64638484
Fax: 0065 64638488
Slovenia
Electrolux Slovenia D.O.O.
Traska Ul. 132
1000 Ljubljana
Tel.: 61 1234 137
Fax: 61 1234 238
Thailand
Olympia Thai Tower, 444
Rachadapiser Road
Samsennok- Huaykwang
10320 Bangkok
Thailand
Tel.: 006625136111
Fax: 006625136334
Slovakia Rep.
Electrolux Slovakia S.R.O.
Seberiniho 1
821 03 Bratislava
Tel.: 02 4333 4322, 4355
Fax: 02 4333 6976
South Africa
AEG (Pty) Ltd.
55, 12th Road
P.O. Box 1 02 64
Kew/Johannesburg 2000
Tel.: 8069111
Hungary
Electrolux Lehel KFT
Erzsébet Királyné útja 87.
1142 Budapest
Tel.: 00361/467-3200
Czech Rep.
ELECTROLUX DOMÁCå
SPOTØEBIÈE CZ
DIVIZE ELECTROLUX S.R.O.
Customer Centre
Hanusova ul.
140 21 Praha 4
Tel.: 2 6112 6112
Telefax: 2 6112 3504
Service
In the event of technical faults, please first check whether you can
remedy the problem yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem yourself, please contact the
Customer Care Department or one of our service partners.
In order to be able to assist you
quickly, we require the following
information:
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers see rating plate)
– Type of fault
– Any error messages displayed by
the appliance
– three digit letter-number combination for glass ceramic
So that you have the necessary reference numbers from your appliance
at hand, we recommend that you write them in here:
Model description:
.....................................
PNC:
.....................................
S No:
.....................................
29
Assembly / Montage
92
93
Rating Plate / Plaque signalétique / Typeplaatje
96901K-MN
55HCDAAAO
949 592 324
230 V
50 Hz
7,9 kW
AEG-ELECTROLUX
94
95
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg-electrolux.de
© Copyright by AEG
822 925 917-A-291105-01
Subject to change without notice
Sous réserve de modifications
Wijzigingen voorbehouden
Download PDF

advertising