• This appliance can be used by children aged 8 upwards and by

IMPORTANT SAFEGUARDS
the power cable.
• Do not install the appliance in rooms containing gas, oil or sulphur. Do not install near
sources of heat.
• Keep the appliance at least 50 cm away
from flammable substances (alcohol etc) or
pressurised containers (eg aerosol cans).
• Do not rest heavy or hot objects on top of
the appliance.
• Clean the air filter at least once a week.
• Avoid using heating appliances near the air
conditioner.
• Always transport the appliance upright or
resting on one side.
Before moving the appliance, empty the
internal circuit completely of water.
After moving the appliance, wait at least 1
hour before starting it
• When putting the appliance away, do not
cover with plastic bags.
• The materials used for packaging can be
recycled.
You are therefore recommended to dispose
of them in special differentiated waste collection containers.
• At the end of its working life, consign the
appliance to a specialist collection centre.
• Use this local air conditioner only as described in this instruction manual.
As with all electrical equipment, whilst the
instructions aim to cover as many eventualities as possible, caution and common sense
should be applied when operating and
installing this appliance.
• This appliance is designed for home air conditioning and must not be used for other purposes.
• It is dangerous to modify or alter the characteristics of the appliance in any way.
• The appliance must be installed in conformity with national legislation regulating electrical equipment and installations.
• If the appliance requires repair, contact a
Service Centre authorised by the manufacturer only. Repairs carried out by unauthorised personnel may be dangerous.
• This appliance must be used exclusively by
adults.
• This appliance can be used by
children aged 8 upwards and by
persons with reduced physical,
sensory or mental capabilities or
who lack of experience and knowledge if they are supervised or
have been given instructions concerning use of the appliance in a
safe way and understand the
hazards involved. Children must
not play with the appliance. Cleaning and user maintenance must
not be carried out by children
unless they are older than 8 and
supervised. Keep the appliance
and its cord out of the reach of
children under 8 years of age.
•
If the power cable is damaged, it must be replaced by
the manufacturer or an
authorised technical service
centre in order to avoid all
risk.
SPECIFIC WARNINGS FOR APPLIANCES WITH
R410A* REFRIGERANT GAS
R410A refrigerant gas conforms to EC regulations on the environment. Avoid perforating
the refrigerant circuit of the appliance.
ENVIRONMENTAL INFORMATION: This unit contains fluorinated greenhouse gases covered
by the Kyoto Protocol. Maintenance and
disposal must be carried out by qualified personnel only (R410A, GWP=1975).
* Verify the type of refrigerant gas used in your
appliance on the rating plate.
• The appliance must be connected to an
efficient earth system. Have your electrical
circuit checked by a qualified electrician.
• Do not use extension cables.
• Before cleaning or maintenance, always
unplug the appliance from the mains socket.
• Never unplug the appliance by pulling on
DESCRIPTION
1 air outlet grille
2 control panel
3 handles
4 castors
5 filter
6 evaporator air intake grille
7 air exhaust hose housing
8 condenser air intake grille
9 power cable
10 drain hose with 2 caps
11 flange with cap
12 air exhaust hose
13 hose adapter (2 pieces)
14 wall mounting accessory
15 window outlet
16 remote control unit (some models only)
15
PREPARING FOR USE
ELECTRICAL CONNECTIONS
Before plugging the appliance into the mains socket, check that:
• The mains power supply corresponds to the value indicated on the rating plate on the back of the
appliance;
• The mains socket and electrical circuit are adequate for the appliance;
• The mains socket matches the plug. If this is not the case, have the plug replaced;
• The mains socket is adequately earthed. Failure to follow these important safety instructions absolves the
manufacturer of all liability.
The power cable must be replaced by a qualified professional only.
The instructions below will enable you to prepare your air conditioner for operation as efficiently
as possible.
Before use, make sure the air intake and outlet grilles are unobstructed.
AIR-CONDITIONING WITHOUT INSTALLATION
Just a few simple steps and your comfort is
ensured with your air conditioner:
• Screw one of the hose adapters
end of the air exhaust hose 12.
13 to one
• Fit the other adapter 13 to the air exhaust hose housing 7
at the back of the
appliance (see fig. A).
• Screw the end of the hose without adapter
to the adapter previously mounted on the
appliance (see fig. A).
2
1
B
• Open the window or French window slightly and position the outlet 15 as shown in
figure C.
A
• Fit the window outlet
15
to the air
exhaust hose 12 as shown in fig. B.
• Place the air conditioner near a window
or French window.
• Make sure the air exhaust hose is unobstructed.
16
C
Keep the air hoses as short and free of
curves as possible to avoid constrictions.
AIR-CONDITIONING WITH INSTALLATION
If required, your appliance can also be installed semi-permanently (Fig. D).
• Fit the wall flange accessory
11
provi-
ded in the hole.
• Fit the air exhaust hose
vant hose 7
13
in the rele-
located on the rear side of
the appliance (see fig. A).
• Screw the wall mounting accessory
14
al tubo uscita aria 12 to the air exhaust
13
or, if necessary, unscrew the
adapter
12 from the air exhaust hose and
hose
replace it with the wall installation terminal
14
(fig. F).
30 cm
30 cm
1
D
Proceed as follows:
• Drill a hole (ø134mm) in an outside wall or
through a window pane.
Respect the height and dimensions of the
hole given in figure E.
2
F
• Insert the other end of the hose 12
the flange
11
on
as shown in fig. G.
134
MAX100 cm
MIN 35 cm
in the window
pane
E
in the wooden
kickboard of a
French window
in the wall: you are
recommended to
insulate the section
of wall using suitable insulation.
G
When the hose 12 is not fitted, the hole can
be closed with the flange cap 11 .
Keep the air hoses as short and free of
curves as possible to avoid constrictions.
NOTE.
When installing the air conditioner semi-permanently, you should leave a door slightly
open (as little as 1 cm) to guarantee correct
ventilation.
17
THE CONTROL PANEL
S
O
Q
P
N
A
B
I
H
G
T
L
M
C
R
D
E
F
DESCRIPTION OF THE CONTROL PANEL
A ON/OFF button
B MODE selection button
Air conditioning, dehumidifying, fan.
C Fan speed selection button (MAX/MED/MIN)
D Timer button
E Programmed operation increase temperature/time button
F Programmed operation decrease temperature/time button
G Display (Displays the temperature values set, room temperature and the programmed
operating time)
H Timer in operation indicator light
I/L/M Fan speed lights
N Fan mode light
O Air-conditioning mode light
P Dehumidifying mode light
Q Alarm light
R Remote control signal receiver
S Light: displays room temperature
T Light: displays set temperature
18
Never turn the air conditioner off by unplugging from the mains. Always press the
button, then wait for a few minutes before unplugging. This allows the appliance to
perform a cycle of checks to verify operation. .
OPERATION
TURNING THE APPLIANCE ON
Plug the appliance into the mains.
Press the ON/OFF button (A) (when turned on, the air conditioner
starts operating in the same mode as when it was turned off).
The display shows the room temperature.
Press the MODE button (B) until the indicator light corresponding
to the required mode lights up:
Light (O): air-conditioning mode
Light (N): fan mode
Light (P): dehumidifying mode
AIR-CONDITIONING MODE
Ideal for hot humid weather when you need to cool and dehumidify the room.
By default, the room temperature is displayed.
Light (S) is on.
To set the required temperature, press the + (E) or - (F) buttons
until the required temperature is displayed. (to switch between °F
and °C, press the E and F buttons together for a few seconds).
Light (T) comes on and light (S) goes off.
Fifteen seconds after setting the temperature, the display switches back to room temperature.
Light (S) comes on again.
You can adjust temperature in air conditioning mode only.
Then select the fan speed by pressing the FAN button (C) until
the indicator light corresponding to the required fan speed lights
up:
MAX:
MED:
MIN:
the air conditioner operates at maximum to reach the
required temperature as rapidly as possible
reduces noise levels but still maintains a good level of
comfort
for silent operation
The most suitable temperature for the room during the summer
varies from 24 to 27°C. You are recommended, however, not to
set a temperature much below the outdoor temperature.
19
FAN MODE
Adjust fan speed by pressing the FAN button (C) as described for the air-conditioning mode.
Remember that the higher the speed, the more air is filtered. If you select "MIN" speed, less air is
filtered but the appliance is also less noisy.
DEHUMIDIFYING MODE
Ideal for reducing the humidity in a room (spring or autumn, damp rooms, rainy spells, etc). When
the dehumidifying mode is selected, the light (P) comes on.
At the same time, the "MIN" fan speed light (M) comes on. In this mode, other speeds cannot be
selected.
Note: remember to fit the air exhaust hose as described in the chapter "Preparing for use".
PROGRAMMING THE TIMER
The timer can be used to delay appliance start up or shut down. This avoids wasting electricity by
optimising operating periods.
How to programme delayed start up
• Plug the appliance into a mains socket and press the ON/OFF button (A), then select the required operating mode and other settings (temperature, fan speed, etc).
• Press the ON/OFF button (A) again to place the appliance in standby mode.
• Press the timer button (D). The timer light "H" flashes.
• Use the + (E) or - (F) buttons to set the number of hours delay before the appliance comes on.
• The time increases or decreases in steps of one hour.
The indicator light (H) flashes until the appliance starts up.
You can set the appliance to come on with a delay of up to 12 hours.
To cancel the timer programme, press the timer button (D) again.
Light (H) stops flashing.
How to programme delayed shut down
• Delayed shut down can be programmed in any operating mode (air conditioning / fan/ dehumidifying).
• Press the timer button (D). The timer light "H" flashes.
• Use the + (E) or - (F) buttons to set the number of hours delay before the appliance goes off.
The time increases or decreases in steps of one hour.
The light (H) flashes until the appliance turns off as programmed.
At the set time, the air conditioner shuts down and remains in standby.
To cancel the timer programme, press the timer button (D) again.
Light (H) stops flashing.
20
USING THE REMOTE CONTROL UNIT (SOME MODELS ONLY)
MODELS WITH REMOTE CONTROL
• Point the remote control at the receiver on
the air-conditioner. The remote control
must be no more than 5 metres away from
the
appliance
(without
obstacles
between the remote control and the
receiver).
• The remote control should be handled
with extreme care and respect. Do not
drop it, expose it to direct sunlight, or
leave it near sources of heat.
MAX 5 metres
DESCRIPTION OF THE REMOTE CONTROL
17) "ON/OFF" button
18) "MODE" button
19) Programmed operation/ decrease/
increase temperature button
20) Pulsante “TIMER”
21) Pulsante selezione di velocità di ventilazione (MAX/MED/MIN)
22) °F/°C switching button
Replacing the batteries
• Remove the cover on the rear of the
remote control;
• Replace the old batteries with two new
LR03 “AAA” 1.5V batteries, inserting them
correctly (see the instructions inside the
battery compartment);
• Replace the cover.
17
19
18
21
20
22
If the remote control unit is replaced or
discarded, the batteries must be removed
and disposed of in accordance with current
legislation as they are harmful to the environment. Do not mix alkaline, standard
(zinc-carbon) and rechargeable (nickelcadmium) batteries.
Do not throw the batteries in the fire as they
could explode or leak dangerous liquids.
TURNING THE APPLIANCE ON
Plug the appliance into the mains.
Press the ON/OFF button (17) (when turned on, the air conditioner starts operating in the same
mode as when it was turned off).
Press the MODE button (18) to select the required mode
COOLING
DEHUMIDIFYING
FAN ONLY
On the control panel, the light corresponding to the selected mode comes on.
For air conditioning/dehumidifying/fan only settings and programming the timer, see page 19-20.
21
TIPS
To get the best from your air conditioner, follow these recommendations:
• close the windows and doors in the room to
be air conditioned.
The only exception is when the appliance is
installed through a hole in the wall.
In this case, you are recommended to
leave a slight draught through a door or
window to guarantee correct ventilation.
• Never use the appliance in very damp
rooms (laundries for example).
• Never use the appliance outdoors.
close doors and windows
• Protect the room from direct exposure to
the sun by partially closing curtains and/or
blinds to make the appliance much more
economical to run;
• Never rest objects of any kind on the air
conditioner;
• Never obstruct the air intake 6 or outlet
1 grilles;
• Make sure there are no heat sources in the
room.
close blinds or curtains
• Make sure the air conditioner is on a level
floor.
do not cover
the appliance
22
CLEANING
Before cleaning or maintenance, turn the
appliance off by pressing the ON/OFF button
(A) or in models with remote control unit, by
pressing the ON/OFF button 17 , then always
unplug the appliance from the mains socket.
CLEANING THE CABINET
You should clean the appliance with a slightly
damp cloth then dry with a dry cloth.
For safety reasons, never wash the air conditioner with water.
Precautions
Never use petrol, alcohol or solvents to clean
the appliance. Never spray insecticide liquids
or similar.
CLEANING THE AIR FILTERS
To keep your air conditioner working efficiently, you should clean the dust filter every week
of operation.
The filter is housed in the intake grille.
To clean the filters, remove the filter as shown
in figure H.
Use a vacuum cleaner to remove the dust
H
collected on the filter.
If it is very dirty, immerse in warm water and
rinse a number of times.
The water should never be hotter than 40°C.
After washing, leave the filter to dry.
Put the filter back in its housing.
START OF SEASON CHECKS
Make sure the power cable and plug are
undamaged and the earth system is efficient.
Follow the installation instructions precisely.
END OF SEASON OPERATIONS
To drain all water from the circuit, first
unscrew in the anticlockwise direction the
external cap from the drain hose on the back
of the appliance then remove the internal
cap (figure I) and allow the water to drain out
into a basin. When all the water has been
drained, close the hose with the 2 caps.
Clean the filter and leave it to dry before putting it back in its housing.
I
23
TROUBLESHOOTING
PROBLEM
CAUSE
REMEDY
The air conditioner
does not come on
•
•
•
no electricity
it is not plugged into the mains
the safety device has tripped
•
•
•
wait
plug into the mains
contact your service centre
The air conditioner
works for a short
time only
•
the air exhaust hose has a constriction
•
•
the air exhaust hose is blocked
•
•
there are bends in the air exhaust hose
•
position the exhaust hose correctly
check there are no obstacles
obstructing air discharge
eliminate the bends
•
•
window open
there are heat sources in the room (burner,
lamp, etc)
the exhaust hose is detached
air filter clogged
the air conditioner is not powerful enough for
the conditions or size of the room
•
•
close the window
eliminate the heat source
•
•
connect the exhaust hose
clean or replace the filter
air purifying filters clogged
•
clean or replace the filters
The air conditioner •
does not operate for
about 3 minutes
after turning it on
the safety device has tripped
•
wait for three minutes
The alarm light Q
comes on
the tank inside the appliance is full.
•
empty the tank (see "End of
season operations) on page
23).
The air conditioner
works, but does not
cool the room
•
•
•
Particular odour in
the room
•
•
SELF-DIAGNOSIS
The appliance has a self diagnosis system to identify a number of malfunctions.
Error messages are displayed on the appliance display.
IF…IS DISPLAYED,
IF…IS DISPLAYED,
IF…IS DISPLAYED,
“Low Temperature”
“High Temperature”
“Probe Failure”
(sensor damaged)
…MEANS:
…MEANS:
…MEANS:
room temperature is too low
room temperature is too
high
contact your local customer
service
24
GUARANTEE/TECHNICAL SPECIFICATION
GUARANTEE AND TECHNICAL ASSISTANCE
TECHNICAL SPECIFICATION
The conditions of the guarantee and technical assistance are given on the certificate
supplied with your appliance.
Power supply voltage
Max. absorbed power
during air conditioning
Refrigerant
Cooling capacity
see rating plate
“
“
“
LIMIT CONDITIONS
Room temperature for
air conditioning
21 ÷ 35°C
Transport, filling, cleaning, recovery and disposal of refrigerant should be performed by a technical service centre appointed by the manufacturer only.
The appliance should be disposed of by a specialist centre appointed by the manufacturer only.
IMPORTANT INFORMATION FOR THE CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EUROPEAN DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special local authority differentiated waste collection centre or a
dealer providing this service.
Disposing of household appliances separately avoids all possible negative consequences for the environment and health deriving from inappropriate disposal and enables
constituent materials to be salvaged, resulting in considerable savings of energy and
resources.
As a reminder of the obligation to dispose of household appliances separately, the product is marked with the symbol of a barred refuse bin.
25
Kutlíkova 17
Budova TECHNOPOL
852 50 Bratislava
Telefón: +421 917 911 845
E-mail: info@dobraklima.sk
https://www.dobraklima.sk
26