Hy-PEM XP Series
Hydrogen made easy
Installation and user manual
Scope of the manual...................................................................4
Introduction.............................................................................4
Hydrogen chain by H2planet.......................................................... 4
Specifications............................................................................................................
Notes on FCC compliance..............................................................................................
Correct use...............................................................................................................
Packing list...............................................................................................................
5
5
6
6
Description...............................................................................6
Installation............................................................................... 7
Receiving the generator................................................................................................ 7
Placing the generator................................................................................................... 7
Symbols used on the generator....................................................................................... 8
Gas connections.......................................................................................................... 8
Electrical connections.................................................................................................. 8
Remote connections (optional)........................................................................................ 8
Cascading (option)...................................................................................................... 9
Auto refill (option).................................................................................................... 10
Initial start-up.........................................................................11
Filling the water tank................................................................................................. 11
Installing the deionizer bag.......................................................................................... 12
Starting the unit....................................................................................................... 13
Operation............................................................................................................... 14
LCD display.............................................................................................................. 14
Menu Tree............................................................................................................... 18
Maintenance............................................................................20
Routine maintenance.................................................................................................. 20
Returning the unit..................................................................................................... 21
Spare parts list.........................................................................22
Scope of the manual
This manual provides operation and maintenance instructions for model HY-PEM XP-100, HY-PEM
XP-160, HY-PEM XP-250, HY-PEM XP-300, HY-PEM XP-500, HY-PEM XP-600, HY-PEM XP-1000
hydrogen generators.
Introduction
Congratulations for buying an Hy-PEM XP easy electrolysis system by H2planet, the greatest and
easiest way to experience hydrogen personal hydrogen production in a simple, safe and suitable
way.
Hy-PEM XP provides you clean ultrapure hydrogen you need with no contaminants ideal for fuelcell use, and with full compatibility with H2planet MyH2 CE certified metal hydrides canisters
product line. You can thus maximize lifespan of both fuel-cells and metal hydrides canister by
relying on a ultrapure hydrogen gas.
Hydrogen chain by H2planet
Hy-PEM XP can be your hydrogen easy supply for all of compatible H2planet hydrogen fuelcell generators of GreenBox and GreenHub series. An entire carbon-free and pollution free
process that can be easily installed thanks to the amazing HYnONE H2planet proposal just
needing water and renewable sources of energy as main ingredients!
Enquire your local H2planet dealer or to greenhub@h2planet.eu for further information about
the most suitable hydrogen on-site production option for your generator and specific needs.
4
Specifications
Specifications of the different models of hydrogen generator
Model HY-PEM XP-100
0 - 100 cc/min at STP
Model HY-PEM XP-160
0 - 160 cc/min at STP
Model HY-PEM XP-250
Hydrogen flow rate
STP: Standard temperature and Model HY-PEM XP-300
pressure (20°C, 1 bar)
Model HY-PEM XP-500
0 - 250 cc/min at STP
Model HY-PEM XP-600
0 - 600 cc/min at STP
Model Hy-PEM XP 1000
0 - 1000 cc/min at STP
0 - 300 cc/min at STP
0 - 500 cc/min at STP
Max outlet pressure
11 bar (159.5 psi)
Purity
99.9999% (grade 6.0) designed for fuel-cells and metal
hydrides canisters refills
Weight (dry)
Power consumption
HY-PEM XP 100 – 160 – 250 – 300
17.5 Kg
HY-PEM XP 500 - 600
18.0 Kg
Hy-PEM XP 1000
20 Kg
Model HY-PEM XP 100
55W
Model HY-PEM XP 160
80W
Model HY-PEM XP 250
110W
Model HY-PEM XP 300
125W
Model HY-PEM XP 500
190W
Model HY-PEM XP 600
220W
Model Hy-PEM XP 1000
320W
Input voltage
120-240V / 50-60 Hz
Fuse (not user replaceable)
120V - 6.3 A.T. 240V – 4 A.T. (5x20)
Pressure accuracy
0.1 bar (± 0.5 %)
Display
Graphic Display, 128x64 Pixels
Index of protection
IP2x
Operating conditions:
- temperature
- relative humidity
+15°C to +40°C
80% up to 31°C, decreasing linearly to 50% at 40°C
Over voltage category
II
Pollution degree
2
Sound pressure level
46 dBA
Case dimensions
230 x 355 x 430 mm (WxHxD)
Notes on FCC compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING!
Any changes or modifications to this equipment not expressly approved by the manufacturer
may void the user's authority to operate the equipment.
Correct use
The hydrogen generator is designed to produce hydrogen for private, reasearch or laboratory
use. The unit must only be operated for this purpose, according to the specifications and
instructions provided in this manual. In particular, the following warnings must be observed at all
times:
- Indoor use only
- Never operate the unit in below-zero temperatures. This will cause irreversible damage
to the electrolysis cell.
- Only use pure water (see “Filling the water tank”).
- Only operate the unit in a room with sufficient ventilation (see “Placing the unit”).
- Always unplug the unit from the mains power supply before accessing the internal
components for replacement.
- Only the parts described in the “Spare parts list” can be replaced by the user.
Packing list
List of items included in the shipment
Quantity
Description
1
1
1
1
1
Hydrogen generator
Instruction manual
Deionizer triangle bag
Water drain with flexible tubing
Power cable
Description
The hydrogen generator produces pure hydrogen (and oxygen as a by-product) by the electrolysis
of water. The key element of the generator is an electrochemical cell assembly which contains a
solid polymer electrolyte. No free acids or alkalines are used. De-ionized or pure, distilled water
is the only liquid which may come into contact with the cell. As this is consumed it must be
refilled from time to time as required.
The generated hydrogen gas is accumulated in the hydrogen/water separator and the desiccant
housing. The pressure is controlled by a pressure transducer. The output pressure is indicated on
the display. The hydrogen is dried by passing it through a drying tube The hydrogen then passes
through the shutoff valve and exits the generator throughthe outlet port at the rear.
Installation
Receiving the generator
All units have been carefully inspected before transport. Visual checks for damage and
functional tests should be performed upon receipt. Any damage must be immediately noted and
reported. The generator must only be returned according to the shipping instructions provided.
Placing the generator
The hydrogen generator must be placed on a flat, level, vibration-free, shock-free surface. Do
not place the generator over a source of heat, as this may cause the device to overheat. The
unit should not be in contact with any other objects on any side, and the air inlet must not be
blocked. Leave at least 30cm of free space at the rear for ventilation. Do not operate the
generator in a sealed or unventilated room, or in close proximity to open flame or other sources
of ignition. Do not operate the generator at below freezing temperatures. Operation is
guaranteed at operating temperatures between +5 and +40°C.
WARNING!
Normal precautions for any hydrogen supply should be taken when using the generator. DO NOT
use in sealed or unventilated rooms. DO NOT use in close proximity of open flames or other
sources of ignition.
Symbols used on the generator
Earth symbol: this symbol marks the earth connections to the chassis of the hydrogen
generator.
Gas connections
Pure dry hydrogen at regulated pressure is available at the hydrogen outlet port at the rear of
the generator. This port must be connected to 1/8" tubing using a stainless-steel or copper
Swagelock connector. Teflon connectors are not suitable. If you purchased H2planet Hy-PEM XP
connection kit (supplied separately on request) just please tighten nut at tip of 1/8” hose by
screwing it un threaded male on back of Hy-PEM XP generator. By the use of a proper monkeywrench tighten the nut gently being sure the nut with hose is well tightened over the male of
the OUTLET port. The pressure at this port is adjusted and shown on the display. The hydrogen
relief port at the rear of the unit can be connected to an exhaust hood or other vent system.
WARNING!
The line from the relief port should never connected in such a way that back pressure can
develop.
IMPORTANT!
Remove the sylicon caps from the OXYGEN
VENT and HYDROGEN VENT plugs before
operating the unit. Keep these caps for unit
storage and/or transportation.
Electrical connections
Check the setting of the voltage selector on the rear of the unit. The set voltage is indicated by
the white arrow. To change the voltage, proceed as follows:
-
Using a small screwdriver, remove the voltage selector insert.
Replace the voltage selector insert so that the white arrow points to the correct voltage.
Remote connections (optional)
The hydrogen generators are fitted with an optional remote control feature, which allows the
user to check the status of the machine from a remote position, and to start/stop the production
of hydrogen.
The contacts used in the remote control are potentially free relay contacts. The contacts can be
configured via software as normally-open or normally-closed (see the Configuration section). The
maximum voltage and current ratings for the contacts are 1A / 48V. The pin configuration of the
remote connector is shown in the table below.
Remote connector pin configuration
Pin
1+2
3+4
5+6
7+8
9+10
11+12
13+14
Description
Start (12-30 VDC polarity not important)
Standby (System not OK)
Reaching normal pressure (Overproduction)
Refill water (Low water)
Low water level (Too low water)
Bad water
Change water (Bad water pre alarm)
Cascading (option)
The RS-485 interface allows up to 10 generators to be operated in parallel mode. One unit has to
be defined as the master, while the others operate in “Slave” mode. All the slaves need to be
configured with individual ID numbers. Communication between the generators requires a
standard D-sub 9 pin serial cable. The serial ports are connected as follows:
Master RS 485 out  Slave 1 RS 485 out - Slave 1 RS 485 in  Slave 2 RS 485 in ....
Configuration
Configuring the Master
1. Enter “menu”.
2. Scroll until the display shows “Master“ and enter: set the value using the +/- buttons to
Yes;
3. Exit and scroll until the display shows “Number of slaves“ and enter: set the number of
slaves connected to the master using the +/- buttons.
4. Exit and scroll until the display shows “ID Nr“ and enter: set 1;
5. Exit.
Configuring the Slaves
1. Enter “menu”.
2. Scroll until the display shows “Master“ and enter: set the value using the +/- buttons to
No;
3. Exit and scroll until the display shows “ID Nr“ and enter: set the ID number of the slave.
Use a different number for each slave, starting from ID Nr. 2
4. Exit.
The configuration is now complete.
Operating in Master Slave Mode
Connect the gas outputs of all the generators to the same line. Open all the main valves.
If the configuration and the serial connection is correct, the slaves will show “Slave Mode“ after
starting up. Change the pressure setting on the master, and the slaves will follow the master.
IMPORTANT!
The cascading function will only work properly if the gas outlets on all the generators are
connected together and the main valves are in the open position.
Auto refill (option)
Description
The auto refill option gives you the possibility to refill the water tank of the generator
automatically from a external water source. You can either use a DI water line or a water
reservoir. The correct refill time is depending on the pressure of the water source.
A higher pressure needs a shorter refill time. Max. pressure is 60 PSIG. If you are using a water
reservoir, make sure the minimum water level in the reservoir is 2-3 feet higher than the top of
the generator.
Installation steps
1. Connect the water tubes and the electric wires as in the diagram above.
2. Configure the generator as followed:
- Set the generator to standby
- Set the auto refill function to ON
- Adjust the auto refill time to 8 s
3. Test the auto refill time as followed:
- Empty the water tank
- Start the generator
- Obtain the refilling level (should be approx 30 to 50 % of the max level)
- If the refill level is to little increase the auto refill time.
- Repeat this steps until you have a correct refilling volume.
Note : every time you go into the auto refill menu, you have to put the generator to standby and
start it again.
Warning
If the refill time is to high, the water tank of the generator can overflow,
and damage the unit.
Initial start-up
Filling the water tank
To fill the generator with water, remove the white/black cap on top of the water tank. Carefully
fill the tank with distilled or deionized water. The conductivity of the water used in the
generator must not exceed 2µS.
Fill the tank to the maximum level indicator. Replace the cap, and the leave the small hole free
for ventilation.
WARNING!
Do not fill the water tank higher than the marked level.
CAUTION
To prevent contamination of the cell assembly, it is important to use only deionized or distilled
water in the generator. Water containing metallic impurities will contaminate or damage the
cell, and will void the warranty.
Installing the deionizer bag
After having filled the tank with water, the deionizer bag (supplied) must be placed in the tank.
Inspect the bag thoroughly for holes or tears, indicated by loose deionizer beads on the outer
surface. If the bag is damaged in any way, discard and replace it with a new one. Only use
original parts (see Spare Parts). Wash the deionizer bag in deionized water before proceeding.
Insert the free end of the “T” fastener through the hole in the centre of the water filler cap,
until it is securely fastened. The bag should not block the outlet at the bottom of the tank. Once
in place, the bag should not be allowed to dry out.
This new triangle deionizer bag has been designed for a higher water purifying capacity. It is
recommendable to use this bag for new generators, in the first 4 to 6 months of operation. After
this time you can use the standard deionizer bag ( see “spare parts”).
Starting the unit
WARNING FOR A PROPER USE: please always double-check that the hydrogen content in the user
device such as hydrogen absorbing MyH2 compatible metal hydrides canister be empty of
hydrogen. You can easily do that before refilling by the Hy-PEM connection kit before connecting
it to Hy-PEM XP back panel. If you need to purge out the remaining hydrogen out of the canister
please do it in a safe ventilated place (possibly outdoor) without sparkles, flames or cigarettes
and connect the male to the quick conenctor female of the MyH2 canister and release last
hydrogen content out by turning the knob counter-clockwise.
Once all of the previous operations have been performed, the generator is ready for operation.:
1. Fill the generator with distilled or deionised water. Mind conductivity of the water used
in the generator must not exceed 2μS.
2. Connect the power supply cable and turn the power switch to the ON position.
3. Enter the desired set pressure, possibly up to 9-10bar to get the best performances to
refill compatible H2panet metal hydrides product series MyH2, using the Menu buttons
and selecting “Pressure adjust”. Push “Exit” button twice to get back to the initial
display window.
4. Press the start button to start the unit.
5. The unit will immediately begin to build up pressure. The LCD display will show the
message "reaching normal pressure", and the H2 flow bar will indicate maximum flow
(fully illuminated).
6. Once the pressure reaches the set value (100%), the LCD display will show the message
"normal pressure" and the H2 flow bar will indicate no flow.
7. Select “Open” to let the hydrogen flow inside the hose/H2planet Hy-PEM XP connection
kit and once pressure value reached the set value readable on “Press. Act.”, purge out
small air and hydrogen quantity by pushing the tip of male Swagelok quick connector for
2-3 seconds in order to purge out every impurity from hosing.
8. Wait again until the act pressure reaches the set value. These values are shown on the
LCD display.
9. Connect the H2planet Hy-PEM connection kit by by the mean of tip male quick connector.
If you need to refill compatible MyH2 metal hydrides canisters please first verify all the
hydrogen has been released and purged out from the canister and pressure inside the
canister be as lower as possible near to 1-2 bar. Push firmly the male connector into the
female of MyH2 metal hydrides storage canister until a click is heard. Please follow
refilling instructions of your MyH2 canister to properly refill it by the use of a basin
containing cool water (max 15°C, the lower the better) and keeping MyH2 in horizontal
position inside the basin. NOTE: refilling procedure could take hours depending on
storage capability of your canister.
10. After the initial pressure drop, the outlet pressure should slowly stabilise at the set
pressure. A continuing drop in pressure indicates a gas leak in the external equipment or
too high hydrogen consumption. When refilling MyH2 cartridges pressure drop is initially
normal due to high absorption capability of the system.
11. The generator is now in normal operating conditions:
12. You will realize the canister is full when the pressure visible on display is the same set
initially and “Flow” indication on display will be zero or nearly zero (“Flow” progressive
indication to zero).
13. Disconnect quick connector on top of your MyH2 canister from it. Push “Close” button
and then “Stop” to finish the procedure. Wait 1-2 minutes before switching I/O button on
back of unit OFF.
IMPORTANT: In the event of any faults or damage, first notify H2planet the problem. Please
also provide full details of the problem, including the model and serial number. Instructions
will then be provided for the service or the return of the unit. Only if return authorization is
provided by the producer as per these instructions, the device will be received and
repaired.
Operation
LCD display
All important operating information is shown on the display.
Layout of the display
Water filling port
LCD display
LED
indicators
Controlling keyboard
Back-side
demi-water
draining port
Water level indicator
The LDC display provide the following information.
First row, status information
Sts shows current information on the operating status of the generator.
The information can be divided into 3 groups:
-
Information: displays normal operating status
Pre-alarm: indicates that a maintenance intervention will soon be required; accompanied
by an audible signal.
-
Alarms: indicates that maintenance intervention is required and that the machine has
been shut down; accompanied by an audible signal.
List of messages displayed
MESSAGE
Standby
Reaching Normal Pressure
Normal Pressure
Normal Flow
Refill Water
Change Water
DESCRIPTION
Device
ready
for
H2
production.
Device producing H2 and
increasing pressure to the
set value
Device producing H2 and has
reached the set pressure
value
Device producing H2 and has
reached the set pressure
value, with H2 flowing
Water level approaching
alarm threshold
The conductivity of the
water has exceeded 33µs
TYPE
Information
Information
Information
Information
Pre-alarm
Pre-alarm
Low Pressure
The set pressure can not be Alarm
reached
Low Water Level
There is too little water in
the tank
The conductivity of the
water has exceeded 38µs
Alarm
High cell voltage
Alarm
Bad Water
High Cell Voltage
ACTION
Press start
Alarm
Fill the tank with
water
Drain and then refill
the tank; change the
deionizer bag
Check for internal or
external leaks. Check
max. H2 consumption
Refill the tank
Drain and then refill
the tank; change the
deionizer bag
Notify service agent
Second row, pressure information
Act is the actual pressure of the hydrogen, while Set is the set pressure.
The pressure can be increased using the  button, or decreased using the  button.
Third row, hydrogen flow
This row displays the current quantity of hydrogen being produced. Each point represents around
10 % of maximum capacity.
This graph also indicates approximately how much hydrogen is being consumed by the connected
equipment.
NOTE
The last point on the flow graph will flash only. This indicates that the generator is producing
at maximum capacity. In normal operation, this should not be the case, as it indicates that the
consumption is too near the maximum limit, and the unit may shut-down if consumption
increases further. Maximum flow is normal when the unit is building up pressure.
Fourth row, water quality
This graph shows the quality of the water.
With more than 3 points illuminated, water quality is good.
If only 3 or less points are illuminated, the conductivity of the water is around 33µS (pre-alarm
level).
If only 1 point or no points are illuminated, the conductivity of the water is equal to or greater
than 38µS (alarm). The generator will be shut down.
Start/Stop-Reset button
The Start/Stop button places the generator in normal operating mode from Standby and viceversa. It is also used to re-start the unit following an alarm. When the problem leading to the
alarm has been resolved, the generator must be reset using the Reset button, and then can be
started by pressing the Start/Stop button.
Exit-Menu button
Silences the audible alarm. When the problem leading to the alarm has been resolved, the Reset
button must be pressed before the generator can be restarted (also see Special functions).
The Reset button is also used to access the menu and select.
The button is also used to exit from a displayed voice of the menu tree.
Menu Tree
Configure parameters
Item
Description
Options / Range
Pressure units
Sets the desired unit of measure bar / psi / kPa
for the pressure
Volume units
Sets the desired unit of measure scm
(standard
Default
bar
cubic scm
for the volume
meters)
scf (standard cubic feet)
Temp. units
Sets the desired unit of measure °C and °F
for the temperature
°C
Pressure rise
Sets how fast the pressure has to 0.1 – 6.8 bar/min
increase. If the pressure increases 1.4 - 100 psi/min
at a slower rate, a low pressure
alarm is activated.
0.3
1.5
Pressure drop Sets a delay in seconds to ignore a 2 - 10 min
delay
pressure drop (override low
pressure alarm)
2
Auto start
Sets
whether
the
unit YES / NO
automatically starts production
when power is switched on.
NO
Beeper
Sets whether the audible signal is ON / OFF
activated in the event of an
alarm.
ON
Master
Configures the unit as the Master YES / NO
for cascading operation
NO
Number
slaves
of Enter the number of
connected to the master
slaves 0 - 32
0
0 - 32
0
ID number
Sets the ID number
Remote
start/stop
mode
Configures the remote start/stop Start/stop, Start
function
Direct control
Remote relay Configures
mode
contacts.
the
remote
relay Normally open (NO)
Normally closed (NC)
only, start/stop
NC
Pre alarms in If set to Yes, the pre alarms are YES / NO
alarm log
also shown in the alarm log.
NO
Lock
Keyboard
If set to Yes, the keyboard will be YES / NO
locked automatically after the
generator is in the main window
for more than 20s. To unlock the
keyboard, press the unlock button
and hold for 5s.
NO
Display
contrast
Adjusts the contrast of the display. 0 - 10
5
Autorefill
If set to ON, the pre-level water ON / OFF
alarm is used to trigger an
OFF
external pump or valve to refill
the water tank
Autorefill
time
Sets the duration of water refilling 0-60 s
after the pump or valve has been
trigged
0
Diagnostic display
Item
Description
Max.
Production Tot.
Total production of hydrogen
99.999
scf
4000.00 scm
Operating time (h)
Total number of hours the unit operation
99.999 hours
Wat. quality (
Actual water conductivity
38
Cell current (A)
Actual cell current
-
Cell voltage (V)
Actual cell voltage
-
Cell voltage peak (V)
The maximum cell voltage in the life of the cell
PS. temp.
Actual temperature of the power supply
PS. temp. peak
The maximum temperature of the power supply reached
S)
S
-
Maintenance
With proper care and maintenance, your hydrogen generator should provide you with years of
trouble-free operation. There are no adjustments to be made to the generator. The only routine
service operations are those described below.
Nevertheless, the generator should be inspected approximately every 2 years. Contact your
supplier via email to techsupport@h2planet.eu
Routine maintenance
The following section describes the maintenance operations required for the correct operation
of the hydrogen generator.
Cleaning
The internal components of the hydrogen generator do not need to be cleaned and should not be
accessed by the user for cleaning. To clean the outside of the unit, only use a damp cloth (no
detergents, acids or aggressive or abrasive substances.
Water refilling
The tank must be refilled when the water level approaches the lower level, and the Refill Water
pre-alarm message appears.
Deionizer replacement
Rinse the water tank and replace the deionizer bags approximately every six months, or
whenever the Change Water message appears.
Installing the new deionizer bag
After having refilled the tank with water, the new deionizer bag must be placed in the tank.
Inspect the bag thoroughly for holes or tears, indicated by loose deionizer beads on the outer
surface. If the bag is damaged in any way, discard and replace it with a new one. Only use
original parts (see Spare Parts). Wash the deionizer bag in deionized water before proceeding.
Insert the free end of the “T” fastener through the hole in the centre of the water filler cap,
until it is securely fastened. The bag should not block the outlet at the bottom of the tank. Once
in place, the bag should not be allowed to dry out.
Returning the unit
In the event of any faults or damage, first notify the agent or distributor who supplied the unit.
If this is not possible, inform the producer directly. Please also provide full details of the
problem, including the model and serial number. Instructions will then be provided for the
service or the return of the unit. Only if return authorization is provided by the producer as per
these instructions, will the device be received and repaired by the producer. If the one year
warranty has expired, or the fault is due to misuse of the unit, all repair and shipping costs are
to be paid by the customer. All other costs are borne by the customer, except as otherwise
expressly agreed upon.
WARNING!
If the unit has to be transported, make sure that the water tank is completely empty, and place
the plug (supplied with the unit)on the oxygen vent at the rear of the unit. Close the small
hole in the cap on the water tank with a strip of adhesive tape. Use suitable packaging. The
unit should be transported in an upright position; this warning should be reported on the
outside of the packaging
List of spare parts HY-PEM XP 1000
p/n
H200-031
H200-030
Hy-PEM XP200-004
HY-PEM XP201-001
HY-PEM XP200-002
H200-005
HY-PEM XP200-003
H200-007
H200-008
Hy-PEM XP200-005
H200-013
H200-014
Hy-PEM XP200-006
Hy-PEM XP200-007
Hy-PEM XP200-015
Hy-PEM XP200-016
H200-021
H200-022
H210000-001
Hy-PEM XP200-011
Hy-PEM XP200-017
HY-PEM XP210-005
HY-PEM XP201-006
H210000-004
DESCRIPTION
Deionizer bag
New deionizer triangle bag
Keyboard
Water tank + level sensor
Water tubing kit
Water drain outlet + tube
Ball valve for cell IN
G/L separator, complete with
fittings
Perma Pure drying tube
Display
Pressure release valve
Gas outlet connector + check
valve
O2 separator
H2 separator
Rear intake fan
Internal circulation fan
Gas ON/OFF valve
Connector for PermaPure tube
Complete cell
Transformer 230 VA 50/60 Hz
Start button 240/120 V 50/60 Hz
Main board
Cables
Cell service (on old cell)
Contacts
For any doubt you can count on our experience and availability by calling
(0039) 02.9098.9883 or by mail at staff@h2planet.eu
PRODUCT AND CERTIFIED IN ACCORDANCE WITH
Download PDF

advertising