Slimline Bun Toaster
VISBT



Thermostatically controlled
Digital temperature display
Polymer coated toasting plate
SLIMLINE BUN TOASTER SPECIFICATION PAGE
MODEL VISBT
Dimensions
Height
Width
Depth
Weight
Electrical
Running Amps
Connection Type
International Option
Machine (OVERALL)
585mm
640mm
375mm
35kg
2.1kw, 50HZ AC, 230v, 1 Phase
10 Amps
BSCHUKO 2/3 PIN PLUG
N/A
Vizu Slimline Bun Toasters have been tested and checked for proper operation before
leaving the factory.
Upon delivery please check the unit for damage. If the unit is damaged, contact the carrier,
or Fast Food Systems, immediately and file a damage claim (found in the back of the
manual) Please retain all packing materials.
Damage must be reported within 7 days of delivery
General Description
The Vizu Slim line Bun Toaster caramelises the cut surface of a bun to give a smooth
caramelised surface, which resists absorption of moisture.
Assembly Instructions
1. Remove all packing from the unit.
2.
3.
4.
5.
Peel off all protective plastic covering from toaster.
Wipe toaster with damp cloth.
Wash all removable parts in warm, soapy water.
Dry everything thoroughly.
PLEASE NOTE THAT THE PLATEN HAS SEPARATE ‘POLYMER’ COATED COVER PLATES.
Installation
Position the Vizu Slim line Bun Toaster in desired position, close to a suitable electrical
supply. Connect to electrical supply.
Note: It should be possible to reach the back of the machine to be able to remove the conveyor
and to gain access to the platen covers for cleaning purposes, and to gain access to the
platen cover turn the thickness adjusting screws whilst the unit is set up to toast buns used.
Operating Instructions
1. Use the left hand red switch to switch the toaster on. The unit will automatically
begin to heat up to its factory set temperature start heating.
TEMPERATURE
INDICATION
SWITCH TO TURN
TOASTER ON
POWER INDICATION
SWITCH TO START AND
STOP THE CONVEYER
SPEED CONTROL
2. Allow machine to reach operating temperature, this may take 20 minutes,
(factory set to 290°C).
3
Prior to toasting buns the thickness of the buns being used must be taken in to
consideration.
4
The gap between the platen and the conveyor can be adjusted using the adjusting
screws on the back of the unit, see fig 3.
5
To remove the ladder belt from the conveyor assembly it must be pushed together
to relieve the tension. Locate the “V” in the belt; this indicates the start & end of
the belt. See fig 4. Once removed the belt can be cleaned/ replaced. To refit
thread it through conveyor assembly and squeeze closed so that the belt can be
joined together
“V” in belt
6
The open link of the belt can be un-hooked once the belt has been held down.
Note:
The direction the belt is fitted on to the conveyor assembly is
important, see fig 5. You will notice that the radiused ends “lead”
the belt with the tails following (i.e. the belt travels from top to
bottom and therefore the belt should be fitted thus)
Cleaning: Every day
1. Switch power “OFF” on unit (RED switch) and remove plug from electrical supply.
2. Remove:
 Bun Feeder top chute
 Bottom Chute
And wash all parts in warm soapy water. Rinse in clean water and dry all parts
thoroughly.
3. Remove the conveyor and tip crumbs and seeds in to a bin.
4. The ladder belt should be wiped with a clean damp cloth. If the belt has become
very dirty it can be removed and washed separately.
5. Wipe the platen covers with a clean damp cloth, do not use excessive amounts of
water or the element could be damaged. It will wear and will need to be replace
periodically – dependant on usage. When it is worn out it should be replaced, buns
will gradually build up a deposit on the toasting surface when this is occurs and is
easy to identify when cleaning.
NB The platen covers are polymer coated. Do NOT use abrasive cleaners,
scouring pads or sharp implements, these will damage the polymer coating and
invalidate the warranty.
DO NOT USE BLEACH
SLIMLINE TOASTER EXPLODED VIEW
167-28
167-15
40-66
CONVEYER ASSEMBLY
167-25
01-67
167-24
167-32
M 10 WAVEY WASHER
M 10 WASHER
MF FF001
167-13
MF VBT01-60
167-12
167-24
MF PLATE
MF VI1392S
M 10
40-15
MF TOASTDIGI
VI SW17
PLATEN ASSEMBLY
167-31
MF 80807001
MF G1-25
167-14
167-26
167-27
Spare Parts List
PART NO.
PART NAME
QTY.
MF817-8877
Black Nylon 66, strain relief cable bush
1
MF167BELT
Ladder Belt To Suit VISBT12.7X3.66X428
1
MFCROWNHEEL
Bun Toaster Conveyor Labels
2
MFTHICKER+T
HINNER
Labels 3 + 4 'Thicker + Thinner'
1
MFVISBTLABEL
Label To Suit Eqvisb 100X1X220MM
1
BESCHUKO
H05Rr-F 2Mtr. Rubber C032
1
MFEUROCONVE
RT
Euro to UK converterplug In black 19-1032
1
MFWASTAHAND
LE
EBP.140-B M8 black handle - Bun Toaster
2
MFTOASTADIGI
Two Stage Thermostat Ac1-5Js2Mw-A (P)
1
HAXXSSRC
Solid State Relay Ssr20A240(Mf701-976-R)
1
IMAGE
PART NO.
PART NAME
QTY.
MFTOASTAPRO
BE
Toasta Probe 504-111
1
MFG125S0832
Spur Gear 15MM Length, 7MM Boss
1
MFG132S1222
Spur Gear 12MM Bore M6 In Centre Boss
1
MF80807001
21 Rpm Motor To Suit Eqvisbt
1
MFP29-25
Elem Toaster Wire Retainer 1Gik1R102001
2
MF504-341
Transformer
1
MF193-026
Bridge Rectifier Quad SKB25/02 17A 1600V
1
MFLC045D17SS
Compression Spring
2
MF167-40
Belt Sprocket 2.5MM 304SS
4
IMAGE
PART NO.
PART NAME
QTY.
MF167-11
Phosphur Bronze Mounting Block
4
VILE14
Switch cover / bezel HD2/HD4 MFF1025 /
MF1026
2
VISW17
Rocker switch HD2 Revolva HD4
MFC1553ALR
2
MF10A250ACS
WITCH
10A 250Vac On-Off-On Single Pole,Db Thr
1
MF374-1029
100mm low profile lens indicator 230VAC
1
MF354Z
2 Pole 5amp term block TB06
1
MF1392S
Black female star knob, M10 thread 8965P
2
MFFF-001
Single Foot
6
IMAGE
PART NO.
PART NAME
QTY.
MFOHSL01
High temperature sleeving
MF536-4062
Ceramic bead ceramic white +1200° C
MF608-244
20mm Male Long Brass Bush For Bun Toaster
1
MF608-250
20mm Female Brass Bush For Bun Toaster
1
MF621-118
20mm 2.87mm Locknut
1
MFVBT01-06
Sprocket Bun Toaster
4
MFVBT01-60
Platen Adjusting Screws Toaster
2
MF167POLY
Set of two - Non-stick coated plates
1
1
500
IMAGE
PART NO.
PART NAME
QTY.
MFBF12x18x12
Bf12X18X12 Bronze Bush
4
LPTOASTERCAR
TON
670X330X620Mm 0201 150Kt Dw Plain Case
1
MF161-1184
Stratotherm Crimps High Temp.
6
MF0CP-006
Turned Hanging Spigot
8
IMAGE
Wiring diagram
Fault Finding
Qualified personnel must only carry out any servicing. Machine must be removed from
electrical supply before any servicing.
Problem
1. Indicated
LED does not
light up
Probable Cause
 No power to
machine.
Solution



Check machine is plugged in and switched
on.
Check fuse in 13a plug.
Check circuit breaker at main supply board
is in (ON).


Check LED
Replace LED
 Insufficient preheat
 Frozen or partially
de-frosted buns.
 Incorrect bun
thickness
adjustment

Allow 20 minutes for pre-heating.

Allow buns to reach room temperature.


Adjust thickness to ensure buns are in
contact with platen
See Section 1
3. Unit will not
heat up,
though
conveyor is
moving
 Thermostat is
defective

Test/replace thermostat
 Element defective.


Test/replace
See Section 1
4. Conveyor
not moving,
platen is hot
 Defective motor
capacitor
 Defective motor/
gearbox

Remove conveyor box and check that drive
gear is turning.
Test/replace capacitor.
Test/replace motor/ gearbox
 Conveyor belt
incorrectly fitted

 LED faulty
2. Buns not
toasted when
machine is
running and
platen hot



Refer to fitting instructions; note direction
of links is important.
See Section 1
Terms and Conditions
Claims
No claim shall be entertained by the Company unless made in writing. Claims arising from
damage or partial loss in transit must reach the Company within 7 days from the date of
delivery. Claims for non-delivery must reach the Company within 10 days from the date of
dispatch. All other claims must reach the Company within 7 days. Damaged goods must be
retained for inspection/collection.
Returns
The Company does not operate a returns policy unless the goods are defective:
In circumstances where the Company agrees to accept return of goods, a charge of 25% of
the invoice value will be made.
Damage claim form
Machine: SLIMLINE BUN TOASTER
Product code: VISBT
Customer name……………………………………………………………
Date of delivery……………………………………………………………
Machine serial number…………………………………………………
Damage comments………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
Please indicate on the picture where the unit is damaged
Courier name…………………………………………………………………
Please cut this page out and post to Fast Food Systems
(The address is on the back of this manual
Warranty
UNITED KINGDOM AND REPUBLIC OF IRELAND
Excepting where otherwise specified all products are subject to 12 months parts and labour
warranty. Goods found defective will be repaired, credited or replaced without charge
according to the terms of the Company’s standard warranty, provided written notice is given
within the guarantee period. In no case will the company be liable for repairs made without
it’s knowledge or sanction, or for indirect damage, or any consequential loss or expense
incurred by purchasers.
Fast Food Systems Ltd, warrants to the original purchaser that the equipment supplied to be
free from defective materials or workmanship for a period of 12 (twelve) months.
The following are NOT covered by warranty:
1.
Failure or breakdown caused by incorrect installation.
2.
Adjustment or calibration of controls - this is a routine maintenance function.
3.
Abuse or misuse, including cleaning.
4.
Warranty labour is only carried out during normal working hours; calls out of hours
may be subject to surcharges.
5.
The warranty will commence either on installation or 1 (one) month from date of
dispatch - whichever is the sooner.
7.
Warranty on spare parts purchased for equipment outside of the warranty period is 3
(three) months from date of sale.
8.
Any faulty spare parts replaced under warranty must be returned with 7 days of
supply.
9.
Warranty is non-transferable.
Fast-Food-Systems Ltd will not be held responsible, financially or otherwise, for any loss
of business as a result of equipment breakdown.
NOTES…
NOTES…
Model Number………………………………
Order ID/Job No……………………………
Machine serial number……………………
Date of Manufacture ……/………/………
Date of delivery……/………/……
Date of commissioning……/………/……
Fast Food Systems Limited
Manufacturer & Distributor of Catering Equipment
Unit 1 Headley Park 9 Headley Road East
Woodley Reading Berkshire RG5 4SQ–
Tel: 0118 944 1100 Fax: 0118 944 0350
Email: service@fa-st-food-systems.co.uk
Website: www.fast-food-systems.com
Issue 9: 06.03.17
Download PDF

advertising