INSTALLATION INSTRUCTION
378- Pendant
PD-37806/PD-37814
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
-
Read all instructions before installing.
-
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
-
Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
-
Place the wall switch in the “OFF” position.
CAUTION
-
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture.
CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
-
Lisez toutes les instructions avant d’installer.
-
Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les
règlements locaux.
-
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
-
Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
-
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
-
Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
-
Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales.
-
Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
-
Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
-
Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
G0
A
B
C
Wire Connector
Qty: 3pcs+1 Extra
7EAC112201
Junction Box Screw
Qty: 2pcs+1 Extra
7MPF0820C1
Mounting Screw
Qty:1 Extra
7MPF0313S1
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
378- Pendant
PD-37806/PD-37814
Fig.1
=
Junction Box
=
A
Wire Connector
Mounting Backplate
=
Canopy
Push up
B
Junction Box Screw
C`
Mounting Screw
Driver 2 1/2” L X 1 1/4” W X 1 1/8” H
3 3/8” L X 1 1/4” W X 1 1/8” H
Cable Gripper
Instruction: Adjust the fixture
wire length by pushing the
cable gripper on the canopy
and pulling the wire as desired.
Lamp Body
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C) from the fixture.
4. Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
5. Connect the Driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig.12)
6. Secure the mounting back plate to the junction box using junction box screws (B).The side of the mounting back plate marked “GND” must
face out.
7. Place the fixture over the mounting plate and secure it with mounting screws (C).
Back Plate Dimensions
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
G0
House Wires
Black
(Hot)
Fixture Wires
White or
Ribbed
House Wires
White
(Neutral)
Fixture Wires
Bare wire
(Ground)
House Wires
Green or Bare Copper
(Ground)
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
4 3/4”
Fixture Wires
Black or
Smooth
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
1 1/3”
1 3/4”
Fig. 2 Wiring
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
Download PDF

advertising