Model Buster V (CE)
Beef Splitting Band Saw
EQUIPMENT
SELECTION . . . . . . . . . . . . . Ordering No.
TABLE OF
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . Page
• Notice to Employer and Safety
Director . . . . . . . . . . . . . . . . . . . . . . . . . 2
• Notice to Operators, Maintenance
and Cleanup Personnel . . . . . . . . . . . . 3
• Parts Diagram and List . . . . . . . . . . . . 4
• Specifications . . . . . . . . . . . . . . . . . . . 12
• Installation Instructions . . . . . . . . . . . 12
• Operation Instructions . . . . . . . . . . . . 13
• Maintenance Instructions . . . . . . . . . 14
Buster V Band Saw
Shower Head . . . . . . . . . . 4006049
Shower Head and Starter 4006072
Spray Tube . . . . . . . . . . . . 4006096
Sanitizer and Starter . . . . 4006077
Auto Sanitizer and Starter 4006086
Spring Balancer . . . . . . . . . . . . . . 4042023
Blade (127 inch) . . . . . . . . . . . . . 1023159
JARVIS
6206019.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
notice to employer
and safety director
Model Buster V (CE)
page 2 of 16
Keep hands clear.
NOTICE TO EMPLOYER AND SAFETY DIRECTOR
AVOID INJURY
1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove any malfunctioning equipment.
2. Ensure that all employees who use this tool are trained in the proper use of this tool and are aware of
the dangers that may arise if they do not follow the procedure outlined in this brochure.
3. Enclosed are four (4) copies of “NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL.” Post one copy on the employees’ bulletin board; give one copy to the operator(s); give one
copy to the maintenance foreman; and give one copy to the sub–contract cleanup / internal cleanup foreman. Additional copies will be provided upon request.
4. The tool is designed and intended to be powerful. This fact should be obvious to your employees, but
you must emphasize it to them.
5. Never make modifications or alterations to the tool. Replace any missing or illegible labels.
6. Ensure that proper procedures are established in accordance with OSHA’s lockout/tagout procedures
(29 CFR 1910.147) to prevent accidental startup or release of stored energy.
7. Follow our installation and maintenance instructions for proper installation and care of the tool.
8. Avoid injury. Do not permit the tool to be misused.
9. If you resell or distribute a Jarvis product, you must provide the purchaser with the appropriate safety
sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided upon
request.
JARVIS
6206019.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
notice to operators, maintenance
and cleanup personnel
Model Buster V (CE)
page 3 of 16
Keep hands clear.
NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL
REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE
REPORT ANY PROBLEMS TO YOUR SUPERVISOR
1. Disconnect the power supply in accordance with OSHA’s lockout/tagout procedures (29 CFR
1910.147) before making any blade changes.
2. Disconnect the power supply in accordance with OSHA’s lockout/tagout procedures (29 CFR
1910.147) before performing any repair or maintenance.
3. Disconnect the power supply – or have the power supply disconnected – in accordance with OSHA’s
lockout/tagout procedures (29 CFR 1910.147) before performing any cleanup.
4. Disconnect the power supply when the tool is not in use.
5. Never put fingers, hands or other parts of the body on the cutting edge or within the cutting path of the
tool when it is connected to the power supply.
6. Test the tool prior to use or daily. Depress each trigger separately and the tool should not start. Depress
both triggers simultaneously and the tool should start. Release either trigger and the tool should stop.
If the tool malfunctions, remove it from service and report or repair it immediately.
7. Test the door interlocks prior to use or daily. Open both the idler and drive end doors individually before
depressing both triggers simultaneously. The tool should not start with either or both doors open. If the
tool malfunctions, remove it from service and report or repair it immediately.
8. Never depress the trigger(s) unless you want to use or test the tool.
9. Never make modifications or alterations to the tool. Report or replace any missing or illegible labels.
JARVIS
6206019.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagram and list
Model Buster V (CE)
page 4 of 16
*
Figure A
Idler End
**
* Tighten to 50 N–m
** Use grease gun 8038001
ITEM
20
21
ITEM
1
2
3
4
5
6
7
8
9
PART NO.
1055338
1055277
1002365
1061201
1039063
1038011
1007176
1055536
1042127
10
11
1021235
1021234
3021006
1057023
1013141
1055363
1042126
1055021
1061220
1029194
1020146
12
13
14
15
16
17
18
19
PART NAME
Flat Head Socket Screw
Flat Head Socket Screw
Idler Wheel Cover
Door Catch
Switch Plunger, Idler End
Grease Fitting
Lock Nut
Socket Head Cap Screw
Support Bracket
(includes item 8)
Roller Bearing Cone
Roller Bearing Cup
Bearing Cup and Cone
Idler Wheel
Internal Retaining Ring
Flat Head Socket Screw
Slide Plate
Socket Head Cap Screw
Slide Rail
Slide Rail Spacer
Idler Wheel Shaft
JARVIS
6206019.
QTY
5
2
1
1
1
1
1
1
1
2
2
1
1
4
1
8
2
2
1

22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
PART NO.
1005047
1016371
1016426
1055862
1004275
1060030
1055026
1004154
1055488*
1006025
1013122
page 7
1042342
1055010
1010145
page 7
1055457
1036127
1032155
1002224
1055270
1036103
1055486
1007177
1067008
1010214
1029195
1055361
1002221
PART NAME
QTY
Door Interlock Switch
1
Idler End Hsg with Sanitizer
1
Idler End Hsg w/o Sanitizer
1
Flat Head Screw
2
Washer
2
Hex Head Threaded Insert
1
Socket Set Screw, Cup Pt.
2
Plain Washer
6
Hex Head Screw
6
Door Knob
1
Internal Retaining Ring
1
Torque Knob Assembly
1
Switch Mounting Bracket
1
Pan Head Screw
2
Dowel Pin
2
Guide Assembly, Idler End
1
Socket Hd Shoulder Screw
2
Bushing (spare part only)
1
Guide Mounting Plate
1
Guide Plate Cover
1
Socket Head Cap Screw
2
Torque Knob Thrust Bushing 1
Hex Head Screw
2
Taper Nut
5
Hinge (includes item 44)
1
Hinge Pin
1
Hinge Spacer
1
Flat Head Socket Screw
4
Hinge Cover
1
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagram and list
Model Buster V (CE)
page 5 of 16
Figure B
Internal Spray
Hot
Cold
A (4006049 and 4006072) = Shower head (cold)
B (4006096) = Rail spray tube (cold)
C (4006077) = Rail spray tube (cold) and sanitizer (hot)
D (4006086) = Rail spray tube (cold) and auto sanitizer (hot)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
A
QTY
B
QTY
C
QTY
D
QTY
1050484
1022173
1050489
1
1
1
1050484
1022173
1050489
1
1
1
1061203
1055287
1050242
1
2
1
1061616
1055287
1050497
1059030
1050260
1
1
1061238
1
1061521
1050488
1050483
1061526
1050496
1
2
1
4
1
1
1
1
1
1050484
1022173
1050489
1050457
1061516
1055333
1050497
1050486
1061521
1050488
1050483
1061526
1050496
1061522
1050487
1050494
1061517
1054128
1035210
1004207
1061523
1004238
1055464
1061519
1004237
1055335
1035365
1061524
1055756
3006007
1050485
1061518
2
2
2
1
1
2
1
4
1
1
1
1
1
1
1
1
1
2
4
2
1
1
1
1
1
1
1
1
2
1
4
1
3022049
1055333
1050497
1050486
1061521
1050488
1050483
1061526
1050496
1061522
1050487
1050494
1061517
1054128
1035210
1004207
1061523
1004238
1055464
1061519
1004237
1055335
1035365
1061524
1055756
3006007
1050485
1061518
1
2
1
4
1
1
1
1
1
1
1
1
1
2
4
2
1
1
1
1
1
1
1
1
2
1
4
1
1050255
1050579
1050731
1012054
1050259
1061239
1
1
1
1
1
1
PART NAME
Hose Connector
Ball Valve
Nipple
Elbow
Manifold
Hex Head Screw
Fitting
Fitting
Tube
Tee
Reducer
Tube
Elbow
Tube
Tee
Reducer
Manifold
Hex Head Screw
O–Ring
Washer
Tube
Sealing Washer
Hex Head Screw
Water Block
Sealing Washer
Hex Head Screw
Gasket
Tube
Pan Head Screw
Knob Extension
Nozzle
Manifold
Fitting
Elbow
Nipple
Bracket
Reducer
Shower Head
JARVIS
6206019.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagram and list
Model Buster V (CE)
page 6 of 16
*
Figure C
**
Drive End
* Tighten to 50 N–m
** Use wrench 8039120
to tighten to 109 N–m
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PART NO.
page 8
1013122
1006025
1004051
1004093
1055304
1055358
page 8
1011307
1017081
1055482
1055485
1004154
1055498*
3063137
1055331
1035208
1044043
1021424
1002213
1026078
1055027
1055344
1016370
1016425
1011217
1055049
1004275
1055862
PART NAME
QTY
Top Handle Assembly
1
Internal Retaining Ring
1
Door Knob
1
Internal Lock Washer
1
Internal Lock Washer
1
Hex Head Screw
1
Hex Head Screw
1
Hanger Assembly
1
Strain Relief Connector
2
Danger Label
1
Pan Head Slotted Screw
4
Flat Head Screw
1
Plain Washer
5
Hex Head Screw
6
Conduit Assembly
1
Hex Head Screw
2
O-ring
1
Bearing Retaining Flange
1
Ball Bearing
1
Bearing Retaining Cover
1
Driven Gear, 86 Teeth
1
Socket Head Cap Screw
4
Hex Head Screw
1
Drive End Hsg w/ Sanitizer
1
Drive End Hsg w/o Sanitizer 1
Drain Coupling
1
Socket Head Cap Screw
4
Washer
2
Flat Head Screw
2
JARVIS
6206019.

ITEM
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
PART NO.
1055499
1061621
1061614
1035207
1029187
1055338
1010214
1055296
1004049
1067007
1032156
1002366
1055277
1055459
1039064
1002209
1061201
1010145
1032155
1036127
1007173**
1057043
1055025
1002219
1058061
1055490
1035210
1005047
1042342
1055010
1061659
1061525
1002218
1055361
page 7
1024063
1055255
PART NAME
QTY
Pan Head Screw
1
Adjustable Nozzle
1
Internal Water Manifold
1
Oil Seal
1
Spacer
1
Flat Head Socket Screw
5
Hinge Pin
1
Hex Head Screw
4
Split Lock Washer
4
Hinge (includes item 35)
1
Nut Cover Plate
1
Drive Wheel Cover
1
Flat Head Socket Screw
2
Socket Head Cap Screw
2
Switch Plunger, Drive End
1
Guide Plate Cover
1
Door Catch
1
Dowel Pin
2
Guide Mounting Plate
1
Bushing (spare part only)
1
Bearing Locknut
1
Drive End Wheel
1
Flat Head Socket Screw
3
Rail Cover, Drive End
1
Blade Guide
1
Pan Head Screw
3
O-ring
1
Door Interlock Switch
1
Switch Mounting Bracket
1
Pan Head Screw
2
Saw Frame Rail
1
Spray Tube
1
Rail Cover, Idler End
1
Flat Head Socket Screw
3
Guide Assembly, Drive End
1
Blade Guide Guard
1
Flat Head Socket Screw
4
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagrams and list
Model Buster V (CE)
page 7 of 16
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
PART NO.
1036103
1514009
1020144
1519137
1021259
1035163
1007041
1006026
1021106
1039024
1002239
1055482
3006005
13
14
15
1006022
1513012
1036124
1036131
1014059
1010213
1010219
1016246
1016247
1061202
1055494
1055502
1058078
1014083
1061231
1058061
1055490
3058057
16
17
18
19
20
21
22
23
24
25
26
3058056
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
pg. 6
44
1035209
1021139
1055437
1016227
1513185
1004069
1010215
1016225
1035009
1560842
page 11
1055357
1004032
1513662
1035206
1055467
1026087
1026078
1055468
1035214
1021240
1021241
1063163
1035216
1063176
PART NAME
QTY
Thrust Bushing
1
Internal Retaining Ring
1
Torque Knob Shaft
1
Woodruff Key
1
Flanged Bearing Race
1
O-ring
1
Hex Lock Nut
1
Torque Knob
1
Roller Bearing
1
Ball Plunger
8
Torque Knob Cover
1
Pan Head Screw
2
Torque Knob Assembly
(includes items 1-12)
Lock Pin Knob
2
Socket Set Screw, Cup Pt.
2
Drive End Lock Pin Bushing
1
Idler End Lock Pin Bushing
1
Compression Spring
2
Drive End Lock Pin
1
Idler End Lock Pin
1
Drive End Guide Housing
1
1
Idler End Guide Housing
Guide Plug
2
Socket Set Screw
4
Socket Head Cap Screw
2
Back-up Blade Guide
2
Compression Spring
2
Blade Guide Mounting Plate
2
Blade Guide Insert
4
Pan Head Slotted Screw
12
Drive End Guide Package
(includes items 13-26)
1
Idler End Guide Package
(includes items 13-26)
1
O-ring
1
Ball Bearing
1
Socket Head Cap Screw
3
Bearing Retaining Flange
1
Socket Head Cap Screw
4
Split Lock Washer
4
Locater Pin
2
Gear Housing
1
O-ring
1
Square Key
1
Electric Motor, 42V/50Hz
1
Hex Head Screw
8
Flat Washer
8
Hex Socket Pipe Plug
2
Oil Seal
1
Socket Set Screw, Cup Pt.
1
Drive Gear, 30 Teeth
1
Driven Gear, 86 Teeth
1
Socket Set Screw, Flat Pt.
1
Motor Accessories, Finned:
1
Gasket Seal
Ball Bearing (Front)
Ball Bearing (Rear)
Rotor
Oil Seal
Electrical Access Plug
JARVIS
6206019.

Figure D
Torque Knob Assembly
Set to release at 81–88 N–m
Torque wrench nut adapter 8030054
Torque wrench 8039138
Figure E
Blade Guide Assembly,
Idler and Drive End
Figure F
Motor and Gear Cover
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagrams and list
Model Buster V (CE)
page 8 of 16
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
Figure G
Hanger Assembly
Figure H
Saw Handle
Assembly
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Figure I
Top Handle
Assembly
JARVIS
6206019.
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38

PART NO.
1055721
1042125
1511610
1028040
1055469
1055455
1050243
1016226
1055471
1061855
1028061
1055367
3061080
1018085
1010145
1019162
1011182
1005114
1016354
1035012
1055629
1004423
1013198
1039051
1014119
1013197
1035507
1002376
1017085
1055943
1007242
1042240
1055033
1529260
1011174
1011307
1063148
1011203
1018086
3019159
3019183
1055328
1018113
1010273
1014096
1013181
1042164
3005017
1035282
1002270
1055592
1063220
1010274
1001049
1055358
1042176
1007022
1007059
1019128
1004182
1055296
3019115
PART NAME
QTY
Socket Set Screw, Cup Pt.
2
Hanger Bracket
1
Cylindrical Bearing
2
Pin and Shackle Link Assy.
1
Socket Set Screw, Cup Pt.
1
Socket Hd. Shoulder Screw
1
Handle and Plug
1
Bearing Retaining Housing
1
Thumb Screw
1
Cylindrical Insert
2
Hanger Link
1
Socket Head Cap Screw
2
Hanger Assy (items1-11)
Right Hand Trigger Lever
1
Dowel Pin
2
Switch Housing and Handle
1
Strain Relief Elbow
1
Switch
2
Switch Housing with item 19
2
O–ring
2
Round Head Screw
4
External Lock Washer
8
External Retaining Ring
2
Plunger
2
Spring
2
Internal Retaining Ring
2
Gasket
1
Housing Cover
1
Electric Danger Label
1
Hex Head Screw
7
Hex Nut
4
Switch Mounting Bracket
1
Button Head Screw
4
Toggle Switch
1
Strain Relief Connector
1
Strain Relief Connector
2
Switch Boot
1
Strain Relief Connector
1
Left Hand Trigger Lever
1
Saw Handle Assembly
(incls items 13-33 & 36–38
for Autosanitizer with Starter
Hex Head Screw
1
Trigger Lever
1
Threaded Pin
2
Spring
1
External Retaining Ring
1
Handle Bracket
1
Switch Assembly
1
O–ring
1
Switch Cover
1
Flat Head Phillips Screw
3
Electrical Connector
1
Threaded Pin
1
Wire with Molded Plug
1
Hex Head Screw
1
Handle Mounting Bracket
1
Hex Lock Nut
1
Hex Lock Nut
1
Switch Handle
1
Washer
1
Hex Head Screw
1
Top Handle Assembly
includes items 39-58)
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagram, list
and wiring diagram
Model Buster V (CE)
page 9 of 16
Figure J
Electric Control Box Assembly
without Starter
ITEM PART NO.
1.
1001014
2.
1011052
3.
1560761
4.
1007130
5.
1063296
6.
1016346
7.
1032265
8.
1055484
9.
1017258
10.
1017085
11.
1063208
12.
1063209
13.
1063312
3063148
PART NAME
QTY
Electrical Cord
4 ft
Strain Relief Connector
3
Seal Ring
3
Locking Nut
3
ATD Circuit Board
1
Electric Enclosure
1
Panel
1
Pan Head Screw
4
Wiring Diagram Label
1
Electric Danger Label
1
Electrical Outlet
1
Electrical Plug (not shown)
1
Pigtail Fuse
1
Electrical Control Box Assy
(includes items 1-11 and 13)
Figure 1a
JARVIS
6206019.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
parts diagram and list
Model Buster V (CE)
page 10 of 16
Figure K
Electric Control Box Assembly
with Starter
ITEM PART NO.
1
1016418
2
1042338
3
1032391
4
1063390
5
1063389
6
1063494
7
1063363
8
1055803
9
1004247
10
1063495
11
1063496
12
1055910
13
1004227
14
1011262
15
1007266
16
1011249
17
1007256
PART NAME
QTY
Electrical Enclosure
1
Terminal Rail
1
Mounting Plate
1
Fuse Terminal Block
1
Fuse
1
Gray Terminal Block
3
Terminal Marker
7
Pan Head Screw
2
Washer
2
Blue Terminal Block
1
Yellow/Green Terminal Block 2
Pan Head Slotted Screw
2
Internal Lock Washer
2
Strain Relief Connector
1
Locking Nut
1
Strain Relief Connector
1
Locking Nut
1
JARVIS
6206019.

ITEM PART NO.
18
1063655
19
1063385
20
1063296
21
1063080
22
1011248
23
1063312
24
1007249
25
1029302
26
1004244
27
1017085
28
1017259
29
1001014
30
1063208
31
1063209
3063149
3063184
PART NAME
QTY
Heater Pack
1
Magnetic Starter
1
ATD Circuit Board
1
Terminal Ring
10
Strain Relief Connector
2
Pigtail Fuse
1
Locking Nut
2
Plastic Spacer
4
Washer
4
Electric Danger Label
1
Wiring Diagram Label
1
Electric Cord
3 ft
Electrical Outlet
1
Electrical Plug (not shown)
1
Electrical Control Box Assy
Electrical Control Box Assy
for Autosanitizer with Starter
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
wiring diagram,
parts diagram and list
Model Buster V (CE)
page 11 of 16
Figure 1b
Electric Control Box Assembly
with Starter
Figure L
Electric Motor
Smooth Housing
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART NO.
1055321
1002342
1035456
1021240
3064001
1013211
1021302
1014141
1016406
1017158
1055039
1063712
1051151
1055849
1035214
1035216
3016343
1008079
JARVIS
6206019.

PART NAME
Socket Head Cap Screw
Motor Cover
O–ring
Ball Bearing
Rotor Assembly
Retaining Ring
Ball Bearing
Wave Spring
Motor Housing
Information Label
Drive Screw
Stator, 42V–50Hz
Threaded Fitting
Socket Set Screw
Gasket
Seal
Housing and Stator, 42V
(includes items 9–14)
Electric Motor, 42V/50Hz
(includes items 1–16)
QTY
6
1
1
1
1
1
1
1
1
1
4
1
2
2
1
1
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
specifications and
installation instructions
Model Buster V (CE)
page 12 of 16
SPECIFICATIONS
Figure 2
Model Buster V
Motor Power
3.3 hp
Operating Voltage
2500 W
42V, 3 phase, 50 Hz
Capacity
180 head / hour
Control Handles
Electric Dual Anti-tie Down
Distance between guides
Blade Length
Overall Length
Weight
19.75 in
502 mm
127 in
3226 mm
57 in
1448 mm
196 lbs
Vibration
Top Handle
To 220V 50Hz
AC Supply
2 ft.
To Starter Coil
Supplied By Customer
88.9 kg
under 128 dB under 2.5 m/s2
Noise (1 meter from tool)
85 dB
Power
Supply
INSTALLATION INSTRUCTIONS
IMPORTANT: ALWAYS DISCONNECT THE POWER SUPPLY
Rear Handles
IN ACCORDANCE WITH OSHA’S LOCKOUT/TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY
MAINTENANCE OR REPAIRS. ALL WIRING MUST BE DONE
20 ft.
IN ACCORDANCE WITH NATIONAL, STATE AND LOCAL
ELECTRICAL CODES.
1 Install the electrical control box in a dry location that
will not be subject to wash downs.
2 Wire the electrical control box (without starter). Refer to Figure 1a on page 9, and Figure 2 on page 12.
2.1 Attach wires numbered 2, 3 and ground to a
220V/50Hz AC power supply.
2.2 Attach wires numbered 4 and 5 to a starter coil
(supplied by the customer). Disconnect any other source of power to the starter coil. The coil operating voltage must be 220V.
2.3 The connection between the Buster V and the
control box is pre–wired and is approximately 22
feet long.
3 Wire the electrical control box (with starter). Refer
to Figure 1b on page 11.
3.1 Attach wires numbered L1, L2, L3, N and PE to
a five wire, 380V/50Hz AC power supply.
JARVIS
6206019.

Safety
Kill
Switch
Power Supply
4 Wire the motor (without starter). Refer to figure 2 on
page 12.
4.1 Motor is designed to operate on 42V/50Hz power. Starter coil signal (220V) will usually operate
a 380V starter with a 380V/42V transformer located between motor and starter.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
installation and
operation instructions
Model Buster V (CE)
page 13 of 16
4.2 Ensure drive end wheel (item 50, figure C, page
6) rotates counterclockwise.
Note: Power supply must be connected to perform the
above test.
5 Wire the motor (with starter). Refer to Figure 1b on
page 11.
5.1 Install 4.5 kva 380V/42V transformer between
motor and control box.
8.1 Adjustment “A” to alter the tilt of the saw:
8.1.1 Move hanger bracket (item 2, Figure G,
page 8) toward the rear of the Buster V to tip
the nose of the saw downward.
8.1.2 Move the hanger bracket (item 2, Figure G,
page 8) toward the front of the Buster V to
tip the nose of the saw upward.
5.2 Ensure drive end wheel (item 50, figure C, page
6) rotates counterclockwise.
8.2 Adjustment “B” to position the saw to cut straight
down the backbone:
Note: Power supply must be connected to perform the
above test.
8.2.1 Turn handle and plug (item 7, Figure G,
page 8) clockwise to cut more to the right.
6 Install the balancer above the work station on a
trolley.
8.2.2 Turn the handle and plug (item 7, Figure G,
page 8) counter-clockwise to cut more to the
left.
Note: The trolley should have sufficient travel to allow
the operator to reach the entire work area. Refer to Figure 3 for dimensions.
9 Attach water hookup and drain hoses:
9.1 Attach cold and/or hot water to hose connector
(item 1, Figure B, page 5).
Figure 3
Overall length 57.00
Rail thickness 1.00
9.2 Attach a drain hose (supplied by customer) to the
drain coupling (item 25, Figure C, page 6).
12.75
OPERATION INSTRUCTIONS
PRIOR TO USE OR DAILY:
19.75
Frame Thickness 1.75
1 Turn on the power.
7 Suspend the Buster V from the balancer.
7.1 Adjust the balancer to the operators’ preference.
8 Adjust the hanger. Refer to Figure 4 for steps 8.1-8.2.
Figure 4
Adjustment “A”
Safety
Kill
Switch
Water
Hookup
Adjustment “B”
6206019.
2.1 Ensure that the dual anti-tie down control handles (the top and the rear handles) are working
correctly:
2.1.1 Depress each trigger separately. The tool
should not start. Depress both triggers simultaneously (within one second of each
other). The tool should start. Release either
or both trigger(s) and the tool should stop.
If the tool malfunctions, remove it from
service and report the problem to your supervisor immediately.
2.2 Ensure that the door interlock switches are working correctly:
Oil Drain
Water Drain
JARVIS
2 Perform the following test:

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
operation and
maintenance instructions
Model Buster V (CE)
page 14 of 16
2.2.1 Open both the idler and drive end doors individually before depressing both triggers
simultaneously. The saw should not start
with either or both doors open. If the tool
malfunctions, remove it from service and
report the problem to your supervisor immediately.
CEDURES (29 CFR 1910.147) WHEN INSTALLING OR REMOVING A BLADE. ALWAYS DISCONNECT THE POWER
SUPPLY IN ACCORDANCE WITH OSHA’S LOCKOUT/TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY MAINTENANCE OR REPAIRS.
Figure 5
2.3 Ensure the Buster V moves freely on its balancer.
3 Making the cut:
blade
torque
guide
knob
blade
guide
Note: If an elevating platform is used, the operator
can keep the Buster V in a horizontal position during
most of the split.
Always avoid using pressure; instead, guide the Buster V.
3.1 Mark the center of the backbone of the carcass
with a knife. This step is necessary only during
the operators’ learning period.
3.2 Start the Buster V.
3.3 Saw through the tail bone using the knife mark as
a guide. The idler end of the Buster V should be
pointing upward while sawing through the tail
bone.
3.4 When the tail bone hits the saw frame rail (item
59, Figure C, page 6), continue to saw until the
tail bone breaks apart and you can follow a path
down the backbone of the carcass. The drive end
of the Buster V should be lower than the idler end
while sawing through the tail bone.
3.5 After the tail and aitch bones have been split, saw
through the loin area. The Buster V should be in
a horizontal position during this cut. Do not
pressure the Buster V; guide the saw to ensure a
straight cut.
3.6 Saw through the shoulder and neck of the carcass. The idler end of the Buster V should be
pointing downward while sawing through the
shoulder and neck.
MAINTENANCE INSTRUCTIONS
IMPORTANT: ALWAYS DISCONNECT THE POWER SUPPLY
IN ACCORDANCE WITH OSHA’S LOCKOUT/TAGOUT PRO-
JARVIS
6206019.

tooth direction
grease
fitting
water
manifold
1 DAILY:
Note: the power supply must be connected to perform
the following operation:
1.1 The Buster V is equipped with dual anti-tie down
control handles (the top and the rear handles) and
door interlock switches. Prior to use, check for
the correct operation of these features:
1.1.1 Depress each trigger separately. The tool
should not start. Depress both triggers simultaneously (within one second of each
other) and the tool should start. Release either or both trigger(s) and the tool should
stop. If the tool malfunctions, repair or remove it from service immediately.
1.1.2 Open both the idler and drive end doors individually before depressing both triggers
simultaneously. The saw should not start
with either or both doors open. If the tool
malfunctions, repair or remove it from service immediately.
1.2 Clean and inspect the blade guide assemblies:
Refer to Figure E on page 7 for referenced items.
Note: the backup blade guides can be replaced or rotated without removing the blade guide mounting plate
from the saw.
1.2.1 Turn off power to Buster V.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
maintenance instructions
Model Buster V (CE)
page 15 of 16
1.2.2 Turn door knob (item 28, Figure A, page 4)
one quarter turn to unlock idler wheel cover
(item 3, Figure A, page 4).
1.2.3 Turn door knob (item 3, Figure C, page 6)
one quarter turn to unlock drive wheel cover
(item 40, Figure C, page 6).
1.2.4 Remove (2) screws (item 20) from both the
drive end and idler end guide housings (item
18).
1.2.5 Slide the blade guide mounting plates (item
24) out of the guide housings (item 18).
1.2.6 Remove (6) screws (item 26) that secure
blade guide inserts (item 25) to blade guide
mounting plates (item 24).
1.2.7 Rotate or replace blade guide inserts (item
25) as required.
1.2.8 Insert a 0.022 feeler gage between the blade
guide inserts (item 25).
1.2.9 Apply a light pressure to the outside of the
blade guide inserts.
1.4.3 Grease the front wheel bearings through
grease fitting (item 6) with food grade wheel
bearing grease.
1.5 Check the oil in the gear housing:
1.5.1 Check the oil level in the gear housing (item
34, Figure F, page 7).
1.5.2 Change the oil if these conditions exist:
• Oil contains water.
• Oil is dark or gritty.
• Any bearing is being replaced.
1.5.3 The saw should be tilted rearward and filled
with approximately 1.5 liters of ISO 68 EP
hypoid gear lube.
1.6 Check the cord and plug assemblies:
1.6.1 Check the cord and plug assembly (items 1,
11 and 12, Figure J, page 9, or items 29, 30
and 31, Figure K, page 10) for wear and replace if necessary.
2 WEEKLY:
2.1 Clean torque knob:
Refer to Figure D on page 7 for referenced items.
1.2.10 Tighten the (6) screws (item 26).
1.2.11 Remove screws (item 21).
2.1.1 Remove the torque knob assembly (items
1–12) from the Buster V.
1.2.12 Rotate or replace the back–up blade guides
(item 22) as required.
2.1.2 Remove (2) screws (item 12).
2.1.3 Remove torque knob cover (item 11).
1.2.13 Tighten the screws (item 21).
2.1.4 Turn the torque knob over.
1.3 Check the rear wheel:
2.1.5 Remove internal retaining ring (item 2).
Refer to Figure C on page 6 for referenced items.
2.1.6 Remove torque knob shaft (item 3).
1.3.1 Turn door knob (item 3) ninety degrees to
unlock drive wheel cover (item 40).
1.3.2 Tighten bearing locknut (item 49) to 109
N–m. Jarvis wrench 8039120 is available.
2.1.10 Work each ball plunger up and down with a
wooden dowel to lubricate the springs.
Refer to Figure A on page 4 for referenced items.
1.4.1 Turn door knob (item 28) ninety degrees to
unlock idler wheel cover (item 3).
1.4.2 Inspect condition of roller bearing cone
(item 10) and roller bearing cup (item 11).
6206019.
2.1.8 Turn the torque knob so that ball plungers
(item 10) are visible.
2.1.9 Pour oil onto the ball plungers.
1.4 Check the front bearings:
JARVIS
2.1.7 Clean all grease out of the torque knob.

2.1.11 Apply Jarvis 1315 White Grease to the ball
plunger top surfaces and to the bearing (item
9).
2.1.12 Install the shaft assembly.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978
maintenance instructions
Model Buster V (CE)
page 16 of 16
2.1.13 Rotate the shaft assembly slightly until you
can feel the balls fall into their holes.
6) so that both guide assemblies are parallel
to the floor.
2.1.14 Install internal retaining ring (item 2).
3.1.4 Remove the blade.
2.1.15 Tighten the ball plungers so that the torque
knob releases (clicks) at 81–88 N–m.
Torque wrench nut adapter 8030054 and
torque wrench 8039138 are available.
3.1.5 Install the new blade (1023159) with teeth
pointing inward, toward the frame.
2.1.16 Install the cover (item 11).
2.1.17 Install the (2) screws (item 12).
2.1.18 Install the torque knob assembly back onto
the Buster V.
3 WHEN NECESSARY:
3.1.1 Open idler wheel cover (item 3, Figure A,
page 4) and drive wheel cover (item 40, Figure C, page 6).
3.1.2 Loosen the blade torque knob (item 30, Figure A, page 4) by turning it fully counter–
clockwise.
3.1.3 Raise the blade guide assemblies (item 34,
Figure A, page 4 and item 63, Figure C, page
6206019.
3.1.7 Twist the blade so that the teeth point downward and set the blade guide assemblies
down over the blade.
3.1.8 Close the wheel covers.
3.1.9 Tighten the blade torque knob after the saw
has run a few minutes.
3.1 Replace the blade:
JARVIS
3.1.6 Tighten the blade torque knob until it
“clicks”.

3.2 Tighten the front wheel:
Refer to Figure A, page 4 for referenced items.
3.2.1 Open idler wheel cover (item 3).
3.2.2 Turn locknut (item 7) counter–clockwise to
loosen idler wheel (item 12).
3.2.3 Turn locknut (item 7) clockwise until hand
tight.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
FAX. 860-347-6978