WARNING: Read all instructions before

LOEW CRIB INSTRUCTIONS
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the
address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully
package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12 - 3 4 of a turn. After crib is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
Page 1 of 10
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow
or comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
•
To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed
on their backs to sleep, unless otherwise approved by your physician.
Strangulation Hazard:
•
Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over over a crib or attach strings to toys.
•
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
•
When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
•
When child is able to climb out or reaches the height of 35 in (89 cm), the crib shall no longer
be used, and the child should be placed in a youth or regular bed.
•
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after
assembly and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if
needed. DO NOT substitute parts.
•
DO NOT use a water mattress with this crib.
•
If refinishing, use a non-toxic finish specified for children’s products.
•
Follow warnings on all products in a crib.
•
Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
•
Infants can suffocate in gaps between crib sides and a mattress that is too small.
Page 2 of 10
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST
27-1/4 INCHES BY 51-5/8 INCHES WITH A THICKNESS NOT
EXCEEDING 6 INCHES.
WARNING
·
DO NOT use this crib if the enclosed or attached instructions
cannot be strictly adhered to. DO NOT use this crib if the child
is able to climb out unaided or is taller than 90 cm. DO NOT
place cords, straps or similar items that could become wound
around the child’s neck in or near this crib. Ensure that the sides
are properly latched or locked in place when the crib is occupied.
The mattress used with this crib should not be more than 15 cm
thick and should be of such length and width that the gap
between the mattress and the sides of the crib is not more than
3 cm when the mattress is pushed into the corner of the crib.
·
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the
crib is properly and securely in place.
Page 3 of 10
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
·
The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51-5/8 inches (1310mm) in length, 27-1/4
inches (690mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152 mm) in thickness.
·
If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
·
DO NOT place bed near windows where cords from blinds or drapes may
strangle a child.
·
DO NOT place items with a string , cord, or ribbon around a child’s neck,
such as hood strings or pacifier cords.
·
DO NOT suspend strings over a toddler bed for any pacifier cords.
·
A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
Page 4 of 10
ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in
which the part is used.
Step #1
Step #2
Step #3
Step #4
Step #5
First side rail and end panels assembly (Page 6).
Mattress support arm assembly.
Stabilizer rail assembly.
Mattress height adjustment (Page 7).
Installation of stabilizer rail into the end panels (Page 8).
Second side rail assembly (Page 9).
Leg frame assembly (Page 10).
END PANEL
SIDE RAIL
MATTRESS SUPPORT
LEG FRAME
Page 5 of 10
STEP #1
1ST SIDE RAIL & END PANELS ASSEMBLY
Attach the first side rail to the end panels by using Allen bolts (AA) with
the lock washers and plain washers. See Detail A.
HARDWARE NEEDED FOR STEP #1:
(AA) 1/4" x 1-3/4" BOLT = 4 pcs
DETAIL A
Lock Washers = 4 pcs
Allen bolt (AA), lock
washer and plain washer
Plain Washers = 4 pcs
Allen Wrench = 1pc
Page 6 of 10
STEP #2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
DETAIL B
LOCK
WASHER
MATTRESS HEIGHT ADJUSTMENT
HEX NUT
STEP #2.1
Lay Mattress Support flat with Stabilizer Rail on each side.
NOTE:
ALLEN BOLT
(BB)
Each end of the arm of the Mattress Support has a hole for the bolt to
pass through that corresponds to the holes located in the frame of the
Mattress Support.
ALLEN
WRENCH
STEP #2.2:
Insert the bolt into the desired hole of the frame through the hole on the
arm support. Fasten the bolt with plain washer, lock washers &
hexagonal nut provided. Repeat procedure on other arms of the
Mattress Support. See DETAIL B.
ALLEN BOLT
(BB)
PLAIN
WASHER
ALLEN BOLT
(BB)
MATTRESS
SUPPORT
WARNING:
Set the Mattress Support to the desired height by adjusting the Support
Arms. The Mattress Support should be at its highest setting for
newborns, then adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the Mattress Support
should be at its lowest position.
B
ALLEN BOLT
(BB)
STEP #2.3:
Install the Stabilizer Rail at ends of the arm support, as illustrated in
DETAIL C.
C
STABILIZER RAIL
OPEN WRECH
DETAIL C
HARDWARE FOR STEP #2:
HEX NUT
LOCK WASHER
PLAIN WASHER
(BB) 1/4" X 1-1/4" BOLT = 8 PCS
ALLEN BOLT
(BB)
HEXAGONAL NUT = 8 PCS
LOCK WASHER = 8 PCS
ALLEN WRENCH
PLAIN WASHER = 8 PCS
OPEN WRENCH = 1 PC
ALLEN WRENCH = 1 PC
Page 7 of 10
STEP #3
INSTALLATION OF STABILIZER RAILS
INTO THE END PANELS
STEP #3.1
The inside surface of both end panels have
pre-installed metal brackets, designed to hold the
Stabilizer Rails. Set both ends of the Stabilizer Rails
into brackets, as illustrated in DETAIL D.
STEP #3.2
Gently lay down the crib then fasten the Stabilizer
Rails with bolts (CC), lock washer and plain washer
provided, as illustration in DETAIL E.
Stabilizer Rail
Mattress Support
HARDWARE FOR STEP #3:
DETAIL E
(CC) 1/4" X 13/16 " BOLT = 04 PCS
DETAIL D
(CC)
LOCK WASHER = 4 PCS
PLAIN WASHER = 4 PCS
ALLEN WRENCH = 1 PC
Page 8 of 10
STEP #4
2ND SIDE RAIL ASSEMBLY
Attach the second side rail to the end panels by using Allen bolts (AA)
with the lock washers and plain washers. See Detail F.
HARDWARE NEEDED FOR STEP #4:
(AA) 1/4" x 1-3/4" BOLT = 4 pcs
DETAIL F
Lock Washers = 4 pcs
Plain Washers = 4 pcs
Allen bolt (AA), lock
washer and plain washer
ALLEN WRENCH = 1 PC
Page 9 of 10
STEP #5
LEG FRAME ASSEMBLY
STEP #5.1
Gently lay the crib on a flat surface. Insert the leg frame to the
bottom of the crib and adjust the leg frame to make sure 4
corners of the leg frame are in line with 4 bottom corners of the
crib.
Allen bolt (DD), lock
washer and plain
washer
DETAIL G
STEP #5.2
Attach the leg frame to the crib by using Allen bolts (DD), lock
washers and plain washers. Refer to DETAIL G and DETAIL H.
After assembly, re-tighten all bolts to a snug fit. DO NOT OVER
TIGHTEN.
Det. H
Det. G
HARDWARE NEEDED FOR STEP #5:
(DD) 1/4" x 1" BOLT = 6pcs
Lock Washers = 6pcs
DETAIL H
Plain Washers = 6 pcs
Allen bolt (DD), lock
washer and plain
washer
ALLEN WRENCH = 1 PC
Page 10 of 10