MILLI GLANCE WALL BASIN MIXER SET

page 1 of 3
MILLI GLANCE
WALL BASIN MIXER SET
201
180
36 REF.
86
60
200
120
8°
SPECIFICATIONS
Recommended use
Domestic, hotel and commerical
Colour availability
Chrome
Pressure rating
Maximum continuous operating pressure
1000kPa
Note: As per AS3500 pressure must be limited
to 500kPA on any new home, extension or
renovation.
Note: For best performance and longer life we
recommend 150 - 500kPa
Temperature rating
Maximum continuous working temperature 65o
Suitable Hot Water Units
Storage Tank - Yes
Continuous Flow - Yes
Gravity Feed - Not Recommended
Stars: 6
WELS
To see the complete Milli range go to
www.reece.com.au/bathrooms
Flow rate: 3.5 L/Min
AS / NZS 3718
Standards
CLEANING RECOMMENDATIONS
We recomment the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by improper treatment is not covered by the product
warranty - refer to warranty conditions on the last page.
The more
stars the more
water efficient
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade
people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range
without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are
correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
WATER
RATING
A joint government and industry program
Licence No. 0133
3.5
litres per minute
When tested at 150, 250 & 350 kpa
in accordance with Standard AS/NZS 6400
www.waterrating.gov.au
WMKA
21009
Tech Page Version 1
page 2 of 3
MILLI GLANCE
WALL BASIN MIXER SET
INSTALLATION INSTRUCTIONS
MILLI GLANCE WALL MIXER SET Installation Instructions
WATER SUPPLY REQUIREMENTS
To ensure optimum performance and customer satisfaction
please adhere to the following:
- Maximum hot water temperature 75°C.
- Recommended minimum working pressure 150kPa.
- Recommended maximum working pressure 500kPa.
NOGGIN
Elbow Thread
Dress Plate
Hot Water
45mm - 65mm
Spout Adaptor
If the water pressure exceeds or is likely to exceed 500kPa,
an approved pressure limiting valve must be fitted.
- Flush out all pipe work prior to installation.
- If the water temperature exceeds 75°C an approved
tempering valve must be fitted.
- Installation should comply with Australian standard
AS3500.1 or relevant local authority requirements.
Cement Sheet
and Tiles
NOGGIN
Cold Water
Failure to comply with the above may void all warranties.
Maintenance and Care
Chrome plated surfaces should be cleaned with mild liquid
detergent or soap and water. Do not use cream cleaners, as
they are abrasive. Use of unsuitable cleaning agents may
damage the surface. Any damage caused in this way will
not be covered by warranty.
Adjustment
Adjustment range from
the tiles to the noggin is
45mm to 65mm, as
shown
Guarantee
This product is guaranteed against faulty workmanship and
materials for 1 year from the date of purchase. Installation
must be done by a licensed plumber or this guarantee will be
void.
the protective cover from the mixer.
4 Remove
Apply Teflon tape to Elbow Thread.
hot and cold water supply, as shown.
2Connect
TEST&CHECK FOR LEAKS.
Noggin
for
lev
el
45mm
eck
25mm
Mixer Breach Assembly
Dress Plate
Spout Adaptor
Wall Outlet
Ch
Centres Distance : 120mm
Gently, push the dress plate to position.
Screw Spout Adaptor to Elbow Thread with a
spanner.
Wall Outlet
Grub Screw
Handle
Grub Screw
Do not remove
the protective
cover until final
fit-off.
Handle
IN0128 revA
Grub Screw
1
Screw the mixer breach assembly in place.
CHECK OUTLET AND MIXER ARE LEVEL.
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
120mm
Wall Outlet to the spout adaptor and
5 Push
centre line and create a 25mm hole and a
fasten Grub Screws to secure Wall Outlet.
3 Mark
45mm hole on the cement sheet and tiles, as
Fit handle to position and tighten grub screw to
shown.
secure handle.
QU
AL
7
YEAR
IT Y
TE
MILLI GLANCE
WALL BASIN MIXER SET
E
page 3 of 3
G UARA
N
REECE PRODUCT QUALITY GUARANTEE
You have purchased a quality product from Reece Pty Ltd
ABN 84 004 097 090 (“Reece”). This product is covered by a
7 year replacement product warranty and a 12 month warranty
over spare parts and labour.
This warranty does not include faults caused by:
7 YEAR WARRANTY – DOMESTIC USE
This warranty covers faults in the product construction, material
and assembly. Products which are within 7 years from the
date of purchase, found upon inspection by an authorised
Reece representative, to be defective in construction, material
or assembly, will be repaired or exchanged with an equivalent
product free of charge. Replaced items become Reece’s
property. This warranty also covers any spare parts included
under “Manufacturer’s Provisions” below.
• Installation or part installation by the purchaser or any person
other than a LICENSED PLUMBER
All replacement products will be available for collection without
charge to the customer at the nearest Reece branch to the
customer’s location, or elsewhere as agreed between the
customer and Reece.
Labour and Spare Parts
The labour for the replacement of products and spare parts
to which this warranty applies will be supplied by Reece or
relevant supplier using licensed plumbers engaged by Reece or
relevant supplier within 1 year from the date of purchase.
Spare parts other than those listed in the Manufacturer’s
Provisions above, which are within 1 year from the date of
purchase found upon inspection by an authorised Reece
representative to be defective in construction, material or
assembly, will be replaced free of charge.
Warranty Conditions
This warranty will apply only under all of the
following conditions:
• The item has been installed by a licensed plumber
• The item has been installed for and subjected to domestic
residential use only
• Failure is due to a fault in the manufacture of the product
• Proof of purchase (including the date of purchase)
is provided
• The installation of the product is in accordance with the
instructions provided
• Incorrect installation or installation not in accordance with
the instructions provided
• Normal wear and tear
• Inadequate or complete lack of maintenance
• Chemical, electrochemical or electrical influences
• Harsh detergents or abrasive cleaners used on
product finishes
1 YEAR WARRANTY – COMMERCIAL USE
‘Commercial’ use is all use other than for normal domestic
residential purposes, including use in non-business places as in
public buildings, schools, sports centres and in establishments
that contain private bathrooms with high frequency of use by
many individuals, such as hotels, motels, retirement villages
and hospitals.
The Commercial warranty covers this product against
manufacturing faults in the construction, material and assembly
of both the finished products and any spare parts for a period
of 1 year from the date of purchase. Products and spare
parts which are found upon inspection by an authorised
Reece representative to be defective in construction, material
or assembly will be repaired or exchanged free of charge.
Replaced items become Reece’s property. The labour for the
replacement of products and spare parts to which this warranty
applies will be supplied by Reece or relevant supplier using
licensed plumbers engaged by Reece or relevant supplier.
The Warranty Conditions and exclusions which apply to the
domestic use warranty also apply to this commercial warranty.
EXCLUSIONS
To the fullest extent permitted by law, Reece excludes all liability
for damage or injury to any person, damage to any property,
and any indirect consequential or other loss or damage.
CLAIM PROCEDURE
For all warranty queries customers are to contact the branch
where the product was purchased. These details can be found
on your purchase invoice.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
TAP.T1.7YR
This warranty does not cover products purchased as an
ex-display without being fully checked and tested for sale by
the manufacturer.
• Unsuitable or improper use
Don’t risk it, use a licensed plumber.™