Contents
DAB/FM Tuner
Introduction ..................................En-2
T-4030
Instruction Manual
Connections .............................. En-10
Enjoying Audio Sources...... En-14
Thank you for purchasing an Onkyo Tuner. Please read
this manual thoroughly before making connections and
plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Tuner.
Please retain this manual for future reference.
Appendix
Troubleshooting ..................... En-22
Specifications ......................... En-23
En
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
En-2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the
manufacturer.
PORTABLE CART WARNING
Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold
with the apparatus. When
a cart is used, use caution
when moving the cart/
apparatus combination to
S3125A
avoid injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and
follow local regulations when disposing of
batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is
adequate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a fluelike gap for warm air to escape.
Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is illegal
without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical solvents,
because they may damage the finish or remove the
panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
5.
6.
7.
8.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons: Pressing
the [POWER] button to select OFF mode does not
fully disconnect from the mains.
If you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains.
If you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the
same ampere rating as that indicated on the plug. Check
for the ASTA mark or the BSI mark on the body of the
fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
For European Models
Declaration of Conformity
We, ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
En-3
Features
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
En-4
DAB+/DAB Capability
Digital Outputs (Optical/Coaxial)
40 FM and 40 DAB+/DAB Preset
FM Digital Output Capability
RDS
Preset Station Naming (Up to 8 Characters)
Automatic/Manual Tuning
FM Mono Mode for Weak Signals
Hi-Rigidity, Anti-Resonant Full Flat Chassis
to Prevent Vibrations
Aluminum Front Panel
Audiophile Grade Capacitor
Remote Interactive (R) System Compatible
Battery-Free Memory Back-Up
Supplied accessories include DAB antenna,
audio and R cables
Contents
Important Safety Instructions............................ 2
Precautions ......................................................... 3
Features ............................................................. 4
Supplied Accessories ........................................ 6
Installing the Batteries............................................... 6
Aiming the Remote Controller.................................. 6
Getting to Know the Tuner ................................ 7
Front Panel ................................................................ 7
Rear Panel ................................................................. 8
Display ...................................................................... 8
Remote Controller..................................................... 9
Connecting Antennas ...................................... 10
Connecting the DAB/FM Antenna.......................... 10
Connecting Your Components........................ 11
Before Making Any Connections............................ 11
Cable and Jacks ....................................................... 11
Connecting to an Amplifier..................................... 12
Connecting Onkyo R Components....................... 13
Connecting the Power Cord .................................... 13
Turning On and Standby ......................................... 13
Listening to the Radio...................................... 14
Listening to FM Stations......................................... 14
Using RDS .............................................................. 17
Listening to DAB Digital Radio ............................. 18
Advanced Setup ............................................... 21
Setting the Display Brightness ................................ 21
Changing radio wave intensity................................ 21
Advanced Setup Menu ............................................ 21
Troubleshooting ............................................... 22
Power....................................................................... 22
Audio....................................................................... 22
Tuner ....................................................................... 22
Remote Controller................................................... 22
Specifications ................................................... 23
En-5
Supplied Accessories
Make sure you have the following accessories:
Installing the Batteries
Remote controller (RC-852T) and two batteries (AAA/R03)
Audio cable
R cable
To use R, T-4030 must be connected with an R cable.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or corrosion.
Aiming the Remote Controller
DAB antenna
* In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the
same regardless of color.
When using the remote controller, point it toward the
tuner’s remote control sensor, as shown below.
Remote control sensor
T-4030
30°
30°
En-6
Approx. 5 m (16 ft.)
Getting to Know the Tuner
Front Panel
a
2 3 4 5
8 9 jk
67
For detailed information, see the pages in parentheses.
a
b
c
d
e
f
k ON/STANDBY button (13, 22)
DISPLAY button (18)
BAND button (14, 18)
PRESET a button (15, 20)
PRESET s button (15, 20)
g
h
i
j
k
PS/RT/PTY button (17, 20)
MEMORY button (15, 16)
TUNING MODE button (14, 16, 19, 22)
TUNING a button (14, 18)
TUNING s button (14, 18)
AUTO SCAN button (16)
En-7
Getting to Know the Tuner—Continued
Rear Panel
1
2
3
4
5
For detailed information, see the pages in parentheses.
a AUDIO OUTPUT jacks (11, 12)
b R REMOTE CONTROL jack (11, 12, 13)
c DIGITAL OUT COAXIAL and OPTICAL jacks
See “Connecting Antennas”, “Connecting Your
Components” for connection (J pages 10 to 13).
(11, 12)
d DAB/FM ANTENNA jack (10)
e POWER CODE
Display
1
For detailed information, see the pages in parentheses.
a Tuning indicators
•
•
•
•
•
AUTO indicator (14)
Tuned
indicator (14)
DAB indicator (18)
FM ST indicator (14)
RDS indicator (17)
b Message area
En-8
2
Getting to Know the Tuner—Continued
Remote Controller
For detailed information, see the pages in parentheses.
a
2
9
3
a
b
c
d
e
f
g
h
i
j
4
k button (13)
DIMMER button (21)
DISPLAY button (18)
BAND button (14, 18)
Arrow [D]/[F]/[A]/[S] and ENTER buttons
(14, 16, 18, 21)
SETUP button (16, 19, 21)
Number buttons (15, 16)
D.TUN button (15)
MODE button (14)
RETURN button (18, 21)
5
6
j
7
8
En-9
Connecting Antennas
This section explains how to connect the supplied
DAB/FM antenna.
The tuner won’t pick up any radio signals if no antenna
is connected, so you must connect the antenna to use the
tuner.
Connecting the DAB/FM Antenna
1
Screw the supplied DAB/FM antenna’s plug
onto the DAB/FM ANTENNA jack.
Once your tuner is ready for use, you’ll need to
tune into a FM radio station or a DAB station and
adjust the position of the DAB/FM antenna to
achieve the best possible reception.
DAB/FM antenna jack
2
En-10
Use thumbtacks or something similar to fix
the DAB antenna into position.
Connecting Your Components
Before Making Any Connections
• Refer to the instructions that came with the component you are connecting.
• Do not plug in the power cord until all other connections are complete.
• Do not bind audio cables with power cords and speaker cables.
Doing so may adversely affect the sound quality.
• To prevent interference, keep power cords and speaker cables as far away as
possible from the antennas.
• Push each plug in all the way to make a good connection
(loose connections can cause noise or malfunctions).
Right!
Wrong!
Cable and Jacks
Optical digital audio
Optical digital connections allow you to enjoy digital
sound such as PCM. The maximum sampling rate for
PCM output is 48kHz/16bit, 2ch.
Coaxial digital audio
Coaxial digital connections allow you to enjoy digital
sound such as PCM. The maximum sampling rate for
PCM output is 48kHz/16bit, 2ch.
Orange
Analog audio (RCA)
White
Analog audio connections (RCA) carry analog audio.
Red
R
To use R (Remote Interactive), you need to connect
your Onkyo AV components with an R cable.
En-11
Connecting Your Components—Continued
Connecting to an Amplifier
R Connection
T-4030
Analog Connection
T-4030
Supplied R cable
Supplied audio cable
Amplifier
Amplifier
Use the supplied audio cable to connect the T-4030’s
AUDIO OUTPUT L/R jacks to the LINE IN jacks on
your amplifier, as shown.
Digital (Optical or Coaxial) Connection
T-4030
Connect either of them.
Amplifier
Use the digital audio cable to connect the T-4030’s
DIGITAL COAXIAL/OPTICAL jacks to the
DIGITAL IN jacks on your amplifier, as shown.
En-12
To use the R system functions, use the supplied R
cable to make an R connection (see the next column).
Note:
• If the T-4030 is used with another Onkyo component,
refer to its instruction manual as well.
Connecting Your Components—Continued
Connecting Onkyo R Components
If you connect the T-4030 to another Onkyo R-capable
component with the supplied R cable and audio cable,
you can use the following system functions. R cables
are special cables solely for use with Onkyo products.
Auto Power On
When you turn on the T-4030, your Onkyo amplifier will
turn on automatically. (The amplifier’s POWER switch
must be set to ON for this to work.)
Direct Change
When you select a radio preset or change the band (FM,
DAB), your Onkyo amplifier will automatically select
the T-4030 as the input source.
Remote Control Operation
You can control the T-4030 by using your Onkyo
amplifier’s remote controller. See the amplifier’s
instruction manual for details.
With R (Remote Interactive), you can control your
R-capable Onkyo CD player, T-4030, and so on with
your amp’s remote controller.
Onkyo amplifier
Connecting the Power Cord
Connect the power cord to a suitable wall outlet.
Note:
• Before connecting the power cord, connect all of
other components.
Turning On and Standby
k ON/STANDBY
1
Press the [k ON/STANDBY] button.
Alternatively, press the remote controller’s
[k ] button.
The tuner comes on, and the display lights up.
To turn the tuner off, press the [k ON/STANDBY]
button, or press the remote controller’s [k ] button. The
tuner will enter Standby mode.
R jack
Onkyo CD player
R jack
T-4030
Notes:
• Push each plug in all the way to make a good
connection.
• Use only dedicated R cables for R connections.
R cables are supplied with Onkyo tuners and players
(DVD, CD, etc.).
• Some components, including the T-4030, have two
R jacks. They’re both the same, so use either one.
• R jacks should be connected only to Onkyo
components.
• Connecting them to another manufacturer’s
component may cause a malfunction.
• Some components may not support all R functions.
See the manuals supplied with your other Onkyo
components for more information.
En-13
Listening to the Radio
Manual Tuning
To activate this mode, press the [TUNING MODE]
button to turn off the “AUTO” indicator. In this
mode, you will receive the broadcast in monaural
sound.
Listening to FM Stations
With the built-in tuner, you can enjoy FM radio
stations.
BAND
3
Press the TUNING [a] or [s] button.
You can also use the remote controller’s arrow
[D]/[F] buttons to tune the radio.
TUNING MODE
TUNING
Auto Tuning
Searching stops when a station is found.
Manual Tuning
The frequency stops changing when you release
the button.
MODE
BAND
The frequency changes in 0.05 MHz steps for FM.
When tuned to a station, the Tuned
indicator
appears. When tuned to a stereo FM station, the FM ST
indicator also appears.
/
1
Use the tuner’s [BAND] button, or the
remote controller’s [BAND] button to select
FM.
Band
Frequency
(Actual display depends on the country.)
2
Press the [TUNING MODE] button or the
remote controller’s [MODE] button so that
the AUTO indicator appears or disappears
from the display.
AUTO indicator
Auto Tuning
To activate this mode, press the [TUNING MODE]
button to turn on the “AUTO” indicator. In this
mode, you will receive the broadcast in stereo
sound.
En-14
Press the buttons repeatedly to change the
frequency one step at a time.
FM ST
Tuning to Weak FM Stereo Stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Listening to the Radio—Continued
■ Tuning into Stations by Frequency
You can tune to FM stations directly by entering the
appropriate frequency.
Presetting FM Stations
PRESET
AUTO
SCAN
MEMORY
TUNING
MODE
TUNING
Number
buttons
&,(,#,5,
ENTER
D.TUN
1
Press the remote controller’s [D.TUN] button.
SETUP
Number
buttons
(Actual display depends on the country.)
2
Within 8 seconds, use the number buttons
to enter the frequency of the radio station.
For example, to tune to 87.50 (FM), press 8, 7, 5, 0.
You can store up to 40 of your favorite FM radio stations
as presets.
Presetting FM stations is performed by the tuner.
1
Tune to the FM station that you want to
store as a preset.
2
Press the [MEMORY] button.
The preset number flashes.
(Actual display depends on the country.)
3
While the preset number flashes (about 8
seconds), use the PRESET [a]/[s] buttons
to select a preset from 1 through 40.
4
Press the [MEMORY] button again to store
the station or channel.
The station or channel is stored and the preset
number stops flashing.
Repeat this procedure for all of your favorite FM
radio stations.
En-15
Listening to the Radio—Continued
■ Selecting Presets
To select a preset, use the number buttons on
the remote controller, the remote controller’s
arrow [A]/[S] buttons or the tuner’s PRESET
[a]/[s] buttons.
4
When you’ve finished editing the name and
want to store it, be sure to use the arrow
[D]/[F]/[A]/[S] button to select “OK” and
then press [ENTER]. If you fail to do this,
the name won’t be saved.
■ Deleting Presets
1
Select the preset that you want to delete.
See the previous section.
2
While holding down the [MEMORY] button,
press the [TUNING MODE] button.
The preset is deleted and its number disappears
from the display.
■ Presetting Automatically
1
• Characters are categorized into two groups: character
set 1 primarily for lower case letters, and character set
2 primarily for upper case letters.
You can select characters in each character set by
pressing the [D]/[F] buttons.
Press the [A]/[S] buttons to select a character to input,
and then press the [ENTER] button to confirm.
If you do not find a character that you want to select in
the currently-displayed character set, press the [D]/
[F] buttons to display string “Shift I J BS OK”, use
the [A]/[S] buttons to select “Shift”, and then press
the [ENTER] button to display the other character set.
• The following table shows available characters.
Press and hold the [AUTO SCAN] button for
3 seconds to start Auto Tuning function.
Up to 40 stations can be preset and presets are
stored in frequency order.
Note:
Depending on your location, a preset may be stored with
no station and you will hear only noise when you select
it. In this case, delete the preset.
■ Name Edit
You can enter a custom name for radio preset for easy
identification. When entered, the custom name will
appear on the display.
The custom name is edited using the character input
screen.
1
Tune to the station of the preset number for
which you want to edit the name, and then
press the [SETUP] button.
2
Use the arrow [D]/[F] button to select
“Name Edit,” and then press [ENTER].
3
Use the arrow [D]/[F]/[A]/[S] button to
select a character, and then press [ENTER].
Repeat this step to enter up to 8 characters.
The meaning of commands other than alphabetical
characters, numbers and symbols is as follows:
Space:
Enters a space character.
Shift*:
Switches the displayed character.
I(Left)/J(Right):
Select these to move the cursor within the Name
input area.
BS (Back Space):
Deletes the character to the left of the cursor.
OK:
Specifies that the entry is complete.
Tips:
* You can also perform this on the remote
controller by using [D.TUN].
En-16
Listening to the Radio—Continued
Using RDS
RDS only works in areas where RDS broadcasts are
available. When tuned into an RDS station, the RDS
indicator appears.
RDS indicator
■ What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data embedded in FM radio signals. It was
developed by the European Broadcasting Union (EBU)
and is available in most European countries. Many FM
stations use it these days. In addition to displaying text
information, RDS can also help you find radio stations
by type (e.g., news, sport, rock, etc.).
The tuner supports four types of RDS information:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting text
information, the text will be shown on the display
(J page 20).
PTY (Program Type)
This allows you to search for RDS radio stations by type
(J page 20).
Notes:
• In some cases, the text characters displayed on the
tuner may not be identical to those broadcast by the
radio station. Also, unexpected characters may be
displayed when unsupported characters are received.
This is not a malfunction.
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
RDS Program Types (PTY)
Type
None
News reports
Current affairs
Information
Sport
Education
Drama
Culture
Science and technology
Varied
Pop music
Rock music
Middle of the road music
Light classics
Serious classics
Other music
Weather
Finance
Children’s programmes
Social affairs
Religion
Phone in
Travel
Leisure
Jazz music
Country music
National music
Oldies music
Folk music
Documentary
Alarm test
Alarm
Display
NONE
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
EASY M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
TEST
ALARM
■ Switching the Display
When receiving RDS, you can press [PS/RT/PTY]
button to switch the information shown in the display.
En-17
Listening to the Radio—Continued
Listening to DAB Digital Radio
Using the Scan Function Manually
With the built-in tuner, you can enjoy DAB digital radio.
BAND
TUNING
1
&,(,#,5,
ENTER
SETUP
RETURN
Press the tuner’s [BAND] button, or the
remote controller’s [BAND] button to select
“DAB”.
When tuned into a DAB station, the station name
will be displayed.
1
Press and hold the [AUTO SCAN] button for
3 seconds to start Auto Tuning function.
To cancel Auto Tuning, press the [ENTER] button.
2
Use the TUNING [a]/[s] buttons to select
the DAB stations.
You can also use the remote controller’s arrow
[D]/[F] buttons to selected DAB stations.
If no station is detected after scanning, “No
Station” appears on the display.
Displaying DAB Radio Information
DISPLAY
Selecting DAB for the Very First Time
The very first time you select DAB, the Auto Tuning
function automatically scans the DAB Band III for the
multiplexes (i.e., stations) available in your area.
Once the scanning process is complete, the first station
that was detected is selected.
DISPLAY
Press the [DISPLAY] button repeatedly to display more
information about the selected DAB station.
1. DLS (Dynamic Label Segment)
When tuned to a station that’s broadcasting DLS text
data, the text will scroll across the display.
En-18
Listening to the Radio—Continued
■ DAB Scan
This setting determines which DAB bands are scanned
by the Auto Tuning function (see page 18).
U.K:
Band III (11B–12D).
W.W (default):Band III (5A–13F).
2. Program Type
Displays the type of program.
3. Bit Rate and Audio Mode
Displays the station’s bit rate and audio mode
(stereo, mono, or joint stereo).
4. Signal Quality
Displays the signal quality.
0–59: Poor reception
60–79: Good reception
80–100: Excellent reception
■ DRC Setting
With the DRC (Dynamic Range Control) setting, you
can reduce the dynamic range of DAB digital radio so
that you can still hear quiet parts even when listening at
low volume levels—ideal for listening to the radio late at
night when you don’t want to disturb anyone.
Use the arrow [A]/[S] buttons to select the following
options, and then press [ENTER].
Off (default): DRC off.
High:
Large reduction in dynamic range.
Low:
Small reduction in dynamic range.
Notes:
• Press [RETURN] to return to the previous menu.
5. Multiplex Name
Displays the name of the current multiplex.
DAB Tuning Mode
6. Multiplex Number and Frequency
Displays the number and frequency of the current
multiplex.
1
2
DAB Setup
&,(,#,5,
ENTER
SETUP
TUNING MODE
RETURN
Press the [TUNING MODE] button.
The items toggle in the order of “Alphabet”
¼ “Multiplex” ¼ “Active St” each time the
[TUNING MODE] button is pressed.
With this setting, you can sort the available stations
alphabetically, by multiplex, or active stations.
Alphabet (default):
Sort stations alphabetically.
Multiplex: Sort stations by multiplex.
Active St: Sort by active stations. Receivable stations
appear at the top of the list. stations that
cannot be received properly appear at the
bottom of the list.
Use the following functions and settings to set up DAB
digital radio.
1
2
Press the [SETUP] button.
Use the arrow [D]/[F] button to select the
item you want to set.
The items are explained below.
En-19
Listening to the Radio—Continued
Displaying Radio Text (RT)
PS/RT/PTY
When tuned to an RDS station that’s broadcasting text
information, the text can be displayed.
1
Press the [PS/RT/PTY] button once.
The RT information scrolls across the display.
Notes:
• The message “Waiting” may appear while the
tuner waits for the RT information.
• If the message “No Text Data” appears on the
display, no RT information is available.
Finding Stations by Type (PTY)
PRESET
AUTO PS/RT/PTY
SCAN
You can search for radio stations by type.
1
Press the [PS/RT/PTY] button twice.
The current PTY appears on the display.
“Not RDS” appears when RDS is not received.
2
Use the PRESET [a]/[s] buttons to select
the type of program you want.
“(PTY selected)?” will be shown on the display.
Note:
• The original display will be shown when an
operation is not performed 5 seconds after a
selection is made.
See the table on page 17.
3
Press the [AUTO SCAN] button to start PTY
scan function.
When the PTY you want to scan is found, the unit
will return to the regular operation.
When the PTY you want to scan cannot be found,
“Not Found” will be shown and the unit will return
to the regular operation.
En-20
Advanced Setup
Setting the Display Brightness
4
You can adjust the brightness of the display.
Press the [ENTER] button on the remote
controller to complete the setting.
Note:
• Press [RETURN] to return to the previous menu.
Advanced Setup Menu
DIMMER
Auto Standby
1
Press the remote controller’s [DIMMER]
button repeatedly to select: dim, dimmer, or
normal brightness.
When “ASb” is set to “On”, the tuner will automatically
enter Standby mode if there is no operation for 30
minutes with no radio station received.
“ASb” will appear on the display 30 seconds before the
Auto Standby comes on.
Default setting: On
Notes:
• With some sources, the Auto Standby function may
activate itself during playback.
Changing radio wave intensity
&,(,#,5,
ENTER
If you weak radio station is frequently received during
AutoPreset/Scan, set the “Search Level” setting to
“Strong” to receive the strong radio station only. The
default setting is “Strong”.
SETUP
RETURN
&,(,#,5,
ENTER
SETUP
RETURN
1
2
Turn on the power.
Press the [SETUP] button on the remote
controller.
The setup menu appears in the display.
3
1
Press the [SETUP] button on the remote
controller.
The setup menu appears in the display.
2
Use the Arrow [D]/[F] buttons to select
“Search Level”, and then press [ENTER].
The Hardware setup menu appears in the display.
3
Use the Arrow [A]/[S] buttons to select
“Normal” or “Strong”.
Use the arrow [D]/[F] buttons to select
“ASb,” and then press [ENTER].
The Hardware setup menu appears in the display.
4
Use the arrow [A]/[S] buttons to select
“ASb On” or “ASb Off”.
5
Press the [ENTER] button on the remote
controller to complete the setting.
Note:
• Press [RETURN] to return to the previous menu.
En-21
Troubleshooting
If you have any trouble using the tuner, look for a
solution in this section.
If you can’t resolve the issue yourself, try resetting
the tuner before contacting your Onkyo dealer.
To reset the tuner to its factory defaults, turn it
on and, while holding down the [TUNING
MODE] button, press the [k ON/STANDBY]
button.
Note that resetting the tuner will delete your radio
presets and custom settings.
Power
Can’t turn on the tuner
• Make sure that the power cord is plugged into the
electric outlet properly.
• Unplug the power cord from the electric outlet, wait 5
seconds or more, then plug it in again.
Audio
There’s no sound or it’s very quiet
• Make sure that all audio connecting plugs are pushed
in all the way (J page 11-13).
• Make sure that the inputs and outputs of all
components are connected properly.
• Make sure that the correct input source is selected.
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance; do not bundle audio cables
together with power cords or speaker cables.
• An audio cable may be picking up interference. Try
repositioning your cables.
Tuner
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear
• Relocate your antenna.
• Move the tuner away from your TV or computer.
• Listen to the station in mono (J page 14).
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
En-22
Remote Controller
The remote controller doesn’t work
• Make sure that the batteries are installed with the
correct polarity (J page 6).
• Install new batteries. Don’t mix different types of
batteries or old and new batteries (J page 6).
• Make sure that the remote controller is not too far
away from the receiver, and that there’s no obstruction
between the remote controller and the receiver’s
remote control sensor (J page 6).
• Make sure that the receiver is not subjected to direct
sunshine or inverter-type florescent lights. Relocate if
necessary.
The tuner contains a microcomputer for signal
processing and control functions. In very rare
situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In
the unlikely event that this happens, unplug the power
cord from the wall outlet, wait at least five seconds,
and then plug it back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
Before disconnecting the power cord from the wall
outlet, set the tuner to Standby.
Specifications
Tuner Section
■ FM
Tuning Frequency Range
87.5 MHz– 108.0 MHz RDS
Preset Channel
40
Signal-to-noise ratio
Stereo: 60 dB (IHF-A)
Mono: 74 dB (IHF-A)
THD (total harmonic distortion) Stereo: 1.0 % (1 kHz)
Mono: 0.2 % (1 kHz)
Frequency response
20 Hz–15 kHz / +1.5 dB, -4.0 dB
Stereo Separation
40 dB (1 kHz)
■ DAB/DAB+
Tuning Frequency Range
Band III:
174.928 MHz–239.200 MHz
Preset Channel
40
General
Power Supply
AC 230 V, 50 Hz
Power Consumption
8W
Stand-by Power Consumption
0.2 W
Dimensions (W × H × D)
Weight
435 × 101.5 × 307 mm
(17-1/8" × 4" × 12-1/16")
4.9 kg (10.8 lbs)
■ Audio Outputs
Digital Outputs
OPTICAL: 1,
COAXIAL: 1
Analog Outputs
L/R
■ Others
R
2
Specifications and features are subject to change without
notice.
En-23
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
http://www.onkyo.com/
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.onkyochina.com/
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
C1206-1
SN 29401267
(C) Copyright 2012 Onkyo Corporation Japan. All rights reserved.