When using electrical appliances especially when children are present, basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and/or injury to persons, including the following:
Do not touch hot surfaces. Use any handles or knobs.
To protect against fire, electrical shock, or injury to persons DO NOT immerse cord, plug or appliance in water or other liquid.
Close supervision is necessary when any appliance is used by or near children.
Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts and before cleaning.
Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
Return appliance to the nearest authorized service facility for examination, repair or adjustment.
The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to
Do not use outdoors.
Do not let cord hang over edge of table or counter or touch hot surfaces.
Do not place on or near a hot gas or electric burner, or in a heated oven.
Extreme caution must be used when moving an appliance containing hot food, hot oil, water or other hot liquids.
Do not use appliance for other than intended use.
To disconnect, turn Off, then remove plug from wall outlet.
Do not attempt to open the Capsule Puncturing Mechanism or the Capsule Drawer during the brewing process or in the few seconds
following the completion of brewing.
Fill the water reservoir of this appliance with water only. Do not fill with other liquids or foods, except when following the specific
instructions in this guide for descaling or cleaning the machine.
This appliance is for HOUSEHOLD USE ONLY. It may be plugged into an AC electrical outlet (ordinary household current). Do not use
any other electrical outlet.
A short power-supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord. Longer
detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If a longer detachable
power-supply cord or extension cord is used,
1. The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, and
2. The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped
over unintentionally.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into
a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug and try again. If it still does not fit, contact a
qualified electrician. Do not attempt to modify the plug in any way.
1. Never pull or yank on cord or the appliance.
2. To insert plug, grasp it firmly and guide it into outlet.
3. To disconnect appliance, grasp plug and remove it from outlet.
4. Before each use, inspect the line cord for cuts and/or abrasion marks. If any are found, this indicates that the appliance should be
serviced and the line cord replaced.
5. Never wrap the cord tightly around the appliance, as this could place undo stress on the cord where it enters the appliance and
cause it to fray and break.
CAUTION: There are two sharp needles that puncture the K-Cup® capsule. One is located above the Slide-Out Capsule
Drawer and the other is in the bottom of the K-Cup® Capsule Holder itself. To avoid risk of injury, do not put your fingers in
or near the K-Cup® Capsule Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup® Capsule Holder during the brewing process. To avoid risk of injury,
do not lift the K-Cup® Capsule Puncturing Mechanism or open the K-Cup® Capsule Drawer during the brewing process.
Sharp Needle Above
Capsule Drawer.
Sharp Needle in
Capsule Holder.
1. Carefully unpack the brewer and all parts. Remove any tape, labels or packaging materials.
2. Wash Removable Water Tank, Water Tank Lid, Drip Tray, Drip Tray Cover, K-Cup® Capsule Holder and Capsule Drawer with warm,
soapy water. Rinse well and dry thoroughly.
3. Wipe exterior surfaces of the product with a soft, moist cloth to remove dust particles collected during packing and handling. NEVER
4. Place Brewer on a solid, level, heat-resistant surface.
Before the first use, the Internal Boiler System of the Coffee Brewer must be primed and cleaned with water.
1. Place the Water Tank on the Brewer and make sure it is properly seated on the water inlet.
2. Fill the Water Tank to the MAX level and replace Water Tank Lid.
3. Press the Release Button on the front of the Brewer to release the Capsule Puncturing Mechanism. See Fig. 1 on Page 7 under
4. Make sure the Capsule Holder is correctly positioned in the Capsule Drawer. Both the Capsule Holder and Capsule Drawer have
a small triangle molded into the plastic housing. These should be aligned in order to properly position the Capsule Holder into the
Capsule Drawer. See Fig. 6 on Page 9 under USER MAINTENANCE INSTRUCTIONS.
NOTE: It is not necessary to use a K-Cup® capsule during the priming phase.
5. Align the Capsule Drawer with the Brewer Housing and press in making sure it is completely closed. See Fig. 2 on Page 7 under
6. Lower the Capsule Puncturing Mechanism. See Fig. 3 on Page 7 under BREWING COFFEE.
NOTE: If the Capsule Drawer is not properly closed, the Capsule Puncturing Mechanism will not lower and latch.
7. Place a large cup on the Drip Tray and beneath the Brew Spout.
8. Plug the Coffee Brewer into an electrical outlet. Ideally, the Coffee Brewer should be operated on its own circuit, separate from other
9. Turn the Coffee Brewer ON by pressing the Power Button. The Power Button will begin to flash and the Brewer will prime the Internal
10. During the priming cycle, the Power Button will continue to flash. When the priming cycle is complete the Power Button will stop
11. After the priming cycle is complete, start the cleaning cycle by pressing the 10oz Button.
12. The Coffee Brewer will heat up and the 10oz Button will begin to flash. The Brewer will run a complete cycle and dispense hot water
to clean the system.
CAUTION: DO NOT remove the cup or mug until the cleaning cycle is complete and the 10oz Button stops flashing.
13. When the cleaning cycle is complete, the Brewer is ready for use.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
1. Place the properly primed Brewer on a dry, level and heat-resistant surface.
2. Fill the Water Tank to the MAX level and make sure it is attached to the Brewer and properly seated on the water inlet. DO NOT place
any liquid other than water in the Water Tank.
NOTE: Always check that the water level in the Water Tank is between the MIN and MAX markings before starting a brew
cycle. If either the 8oz or 10oz brew size button is pressed, the Brewer will run through a full brew cycle even if there
is not enough water to brew a cup of coffee.
3. Press the Release Button on the front of the Brewer to release the Capsule Puncturing Mechanism (Fig. 1).
4. Remove the Capsule Drawer from the Brewer and insert a K-Cup® capsule into the Capsule Holder.
NOTE: Never remove or puncture the foil top of the K-Cup® capsule before inserting into the Brewer.
5. Replace the Capsule Drawer into the Brewer making sure it is completely closed (Fig. 2).
6. Lower the Capsule Puncturing Mechanism (Fig. 3). The K-Cup® capsule will be punctured on the top and bottom allowing for the
ideal flow of water during the brewing cycle.
NOTE: If the Capsule Drawer is not properly closed, the Capsule Puncturing Mechanism will not lower and latch.
7. Turn the Brewer ON by pressing the Power Button. All three buttons will be illuminated (Fig. 4 shows Brewer Control Buttons).
8. Place a mug on the Drip Tray and under the Brew Spout.
TIP: If using a taller mug which will not fit underneath the brew spout, remove the Drip Tray and place the taller mug on
the Brewer Base. Be sure to keep the mug in place at the end of the brew cycle to catch any excess drips, since the drip
tray is not in place. The end of the brew cycle is indicated when the function button is no longer blinking.
Drip Tray
For Use
Drip Tray
In Place
9. Select the brew size by pressing either the 8oz or 10oz button. The brew cycle will now begin and the brew size button selected will
flash throughout the brewing cycle.
TIP: To stop the brewing cycle at any time, press the flashing button.
10. When the brew cycle is complete, the flashing button will stop and all three buttons will illuminate. Five minutes after the brew cycle
is complete, the Brewer will automatically shut off.
11. Do not leave used coffee capsules in the Brewer. Wait for the Brewer to cool before removing used capsules as they remain hot
following the brew cycle. Press the Release Button on the front of the Brewer, slide out the Capsule Drawer and carefully remove the
used capsule and discard. Replace the Capsule Drawer into the Brewer and lower the Capsule Puncturing Mechanism.
This appliance contains no user serviceable parts. Do not try to repair it yourself. Refer it to qualified service personnel if servicing is
needed. The Brewer should be cleaned on a regular basis to prolong the life of the machine and to guarantee optimal brewing results.
• Turn off the Brewer and unplug from the wall outlet.
• On a regular basis, check the Drip Tray for excess water or coffee. Empty the Drip Tray and wipe it clean with a damp cloth. Use
extra care when removing or emptying the Drip Tray, in order to prevent spilling any excess liquids from the Drip Tray.
• DO NOT leave used coffee capsules in the Capsule Holder.
• Wipe down the outside surfaces of the Brewer with a damp cloth and dry thoroughly. NEVER use harsh chemicals or abrasive
cleaning pads. NEVER immerse the Brewer in water or any other liquid and NEVER place the appliance under running water.
• To remove the Capsule Holder from the Capsule Drawer, lift straight up. To properly position the Capsule Holder into the Capsule
Drawer, lower the Capsule Holder straight into the opening in the Capsule Drawer. Both the Capsule Holder and Capsule Drawer
have a small triangle molded into the plastic housing. These should be aligned in order to properly position the Capsule Holder into
the Capsule Drawer (Fig. 5 and Fig. 6).
Fig. 5
Fig. 6
The bottom rounded portion of the Capsule Holder can be removed for further cleaning, including the lower needle. Should the lower
needle become clogged because of coffee grinds a small household object or tool can be used to unclog the needle. Use caution as
the needle is sharp. To remove the bottom portion of the Capsule Holder gently squeeze the rounded portion and pull until the lower
section releases from the top section. To replace, use the two tabs on the bottom section as a guide and snap into place from the top.
Clean the Capsule Drawer, Capsule Holder, Drip Tray and Drip Tray Cover with warm, soapy water. Do not use harsh chemicals or
abrasive cleaners. Dry thoroughly prior to use. The Capsule Drawer, Capsule Holder, Drip Tray and Drip Tray Cover can be placed
onto the top shelf of a dishwasher. Use low temperature cycles if cleaning the parts in the dishwasher.
It is advised to descale the Brewer on a regular basis. Frequency of descaling the Brewer depends on amount of use and your local water
conditions. As a general time frame, the Brewer should be descaled every three months. Specific descaling products for coffee makers
are available in stores and online.
Follow the specific instructions for the descaling product on the package from the descaling product manufacturer.
Make sure the Brewer is turned Off.
Fill the Water Tank with undiluted white vinegar or if using a descaling product fill according to the instructions on the package of the
descaling product.
Place a large mug on the Drip Tray and beneath the Brew Spout.
Make sure there is not a coffee capsule in the Capsule Holder.
Push the Capsule Drawer properly in place.
Close the Capsule Puncturing Mechanism and start a brew cycle without a coffee capsule.
Power off the Brewer just after it begins to dispense and then allow it to sit for at least 30 minutes.
After allowing to sit, run another brew cycle without adding a coffee capsule. Empty the dispensed liquid that has accumulated in
the mug. Use extreme caution as contents may be hot.
Fill the Water Tank with 8 ounces of distilled or bottled water and run a full brew cycle.
Run three additional brew cycles using distilled or bottled water, each time without a coffee capsule. This will clean the Brewer and
get rid of any residual taste from the vinegar or descaler.
The Brewer is now ready for regular use again.
• Be sure all parts are clean and dry before storing. Store appliance in its box or in a clean, dry place. Never store it while it is hot or
wet. Never wrap cord tightly around the appliance; keep it loosely coiled.
• ALWAYS store the Brewer in an upright position, as a small amount of water may remain in the boiler.
SELECT BRANDS, INC. warrants, subject to the conditions stated below, that from the date of purchase, this product will be free from
mechanical defects for a period of one (1) year. SELECT BRANDS, INC., at its option, will repair or replace this product found to be
defective during the warranty period. Should this product become defective by reason of improper workmanship or material defect during
the specified warranty period, Select Brands, Inc. will repair or replace the same effecting all necessary parts replacements for a period
of one year from the date of purchase.
Transportation charges on parts, or products in whole, submitted for repair or replacement, under this warranty, must be borne by the
CONDITIONS: This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep
the original sales receipt. Proof of purchase is required to obtain warranty service or replacement. Dealers, service centers, or retail
stores do not have the right to alter, modify or in any way, change the terms and conditions of this warranty.
Warranty registration is not necessary to obtain warranty on Select Brands, Inc. products. Save your proof of purchase receipt.
ABOUT YOUR PRODUCT WARRANTY: Most warranty repairs are handled routinely, but sometimes requests for warranty service
may not be appropriate. For example, warranty service would NOT apply if the product damage occurred because of misuse, lack of
routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date
or the serial number on the product has been removed or the equipment has been altered or modified. During the warranty period, the
authorized service dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal use
and service.
NORMAL WEAR: This warranty does not cover normal wear of parts or damage resulting from any of the following: Negligent use or
misuse of the product; Improper voltage or current; Use contrary to the operation instructions; Deviation from instructions regarding
storage and transportation; Repair or alteration by anyone other than SELECT BRANDS, INC. or an authorized service center. Further,
the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes.
SELECT BRANDS, INC. shall not be liable for any incidental or consequential damages caused by the breach of any express or implied
warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is
limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province
to province.
HOW TO OBTAIN WARRANTY SERVICE: You must contact SELECT BRANDS, INC. Customer Service at 1-913-663-4500. A Customer
Service representative will attempt to resolve warranty issues over the phone. If telephone resolution is not possible, the Customer
Service representative will require your assistance in performing routine diagnostic procedures. This warranty is effective for the time
periods listed above and subject to the conditions provided for in this policy.
To register this product and view other fine products, visit us online at www.selectbrands.com
K-Cup® is a registered trademark of Keurig, Incorporated.
Neither Select Brands, Inc or TRU™ has any affiliation with Keurig, Incorporated.
This product is not manufactured, distributed, licensed, or endorsed by Keurig, Incorporated.
TRU™ is a registered trademark of Select Brands, Inc. 66219
Made in China
Download PDF