Instruction Manual
This manual contains sections of Safety
Instructions,Operating Instructions,
Installation Instructions and Troubleshooting
Tips etc. Carefully reading it before using the
dishwasher will help you to use and maintain
the dishwasher properly.
To review the section on Troubleshooting Tips
will help you to solve some common problems
by yourself and not need to ask for the help of
professional technicians.
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . 2
Dishwasher Features . . . . . . . . . . . . . . . . . 2
Wash Cycle Table . . . . . . . . . . . . . . . . . . . . 3
Water Softener . . . . . . . . . . . . . . . . . . . . . . 4
Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . 5, 6
Loading the Dishwasher Rack . . . . . . . . 6,7
Turning On the Appliance . . . . . . . . . . . . . . 7
Filtering System . . . . . . . . . . . . . . . . . . . . . 8
Caring for the Dishwasher . . . . . . . . . . . . . 9
About Electricity connection . . . . . . . . . . 9
Water Connection . . . . . . . . . . . . . . . . . . . 10
Before calling for service. . . . . . . . . . 11,12
The manufacturer, following a policy of constant
development and up-dating of the product, may
make modifications without giving prior notice.
„ This appliance must be grounded. In the event
of a malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a
path of least resistance of electric current. This
appliance is equipped with a cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate
outlet that is installed and grounded in accordance
with all local codes and ordinances.
„ Do not abuse, sit on, or stand on the door or dish
„ Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if you
are in doubt whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance; If it is not fit
for the outlet. Have a proper outlet installed
by a qualified electrician.
„ Keep children away from detergent and rinse aid, keep
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
Do not operate your dishwasher unless all
enclosure panels are properly inplace. Open
the door very careful ly if the dishwasher is
operating,there is a risk of water squirting out.
Do not place any heavy objects of stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;
2) Load sharp knives with the handles up to reduce
the risk of cut-type injuries.
3 ) Warning:Knives and other utensils with sharp points
must be loaded in the basket with their points down
or placed in a horizontal position.
When using your dishwasher, you should prevent
plastic item from contacting with heating element.
Check that the detergent receptable is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic
items not so marked, check the manufacturer's
Use only detergent and rinse additives designed
for an automatic dishwasher. Never use soap,
laundry detergent, or hand washing detergent
in your dishwasher. Keep these products out of
the reach of children.
Other means for disconnection from the supply must „
be incorprated in the fixed wiring with at least 3mm
contact separation in all poles.
children away from the open door of the dishwasher,
there could still be some detergent left inside.
Young children should be supervised to ensure that
they do not play with the appliance.
The appliance is not intended for use by young
children or infirm persons without supervision.
Dishwasher detergents are strongly alkaline,they
can be extremely dangerous if swallowed.Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
The door should not be left in the open position
since this could present a tripping hazards.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains
using new hose sets and that old hose-sets should
not be reused.
The maximum number of place settings to be washed
is 12.
The maximum permissible inlet water pressure is 1Mpa.
The minimum permissible inlet water pressure is 0.04Mpa.
To get the best performance from your dishwasher,read all operating instructions before using it for the
first time.
3 4
5 6
Power on light: To come on when Power ON/OFF
button is pressed down.
ON/OFF Button: To turn on/off the power supply.
Delayed Start Button: Press this button to set the
delayed hours for washing. You can delay the start
of washing up to 24 hours. One press on this
button delays the start of washing by one hour.
Half washing light: To come on when select the
Half wash.
Half washing key-press:To select half washing.
(Optional half washing means that the lower spray arm
does not run, so you should load the upper basket only).
Salt and Rinse Aid Warning Light: To come on when
the softener or dispenser needs to be refilled.
Program indicator light: when you select washing
program, the correspond light will display.
Delay time: To display booking time .
Program Key-press:To select washing program
when press the Key-press.
Upper Basket
Spray Arms
Lower Basket
Water Softener
Main Filter
Detergent Dispenser
Cup Shelf
Silverware Basket
Coarse Filter
Rinse Aid Dispenser
Drain pipe connector
Inlet pipe connector
For the heaviest soiled loads,
such as pots,pans,casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
Wash (60 ℃)
Rinse (70 ℃)
5/22 g.
For normally soiled loads,
such as pots , plates,gl asses
and lightly soiled pans.
standard daily cycle.
Pre -wash
Wash (50 ℃)
Rinse (65 ℃)
5/25 g.
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
Wash (45 ℃)
Rinse ( 60℃)
22 g.
For lightly soiled loads,
such as glasses, crystal and
fine china.
Wash (40 ℃)
Rinse (70 ℃)
15 g.
To rinse dishes that you
plan to wash later that day.
Longer inlet time.
Faucets is not opened.
Longer draining time.
The installation position of the drain pipe is too high.
Longer heating time,
but not reaching required temperature
Malfunction of temperature sensor or of heating element.
Too much inlet water. .
Failure of temperature sensor
Open circuit or break of temperature sensor
Failure of temperature sensor
Short circuit or break of temperature sensor
If overflow occurs, turn off the main water supply before calling a service. If there is water in the base pan because of an overfill
or small leak, the water should be removed before restarting the dishwasher.
There are two ways to reduce the water hardness: one way is using water softener, the other is using
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliances is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should be filled as follows:
Remove the lower basket and then unscrew and remove the cap from the salt
If you are filling the container for the first time ,fill 2/3 of its volume with water
(around 500ml).
Place the end of the funnel(supplied) into the hole and introduce about 1.2kg of
salt .It is normal for a small amount of water to come out of the salt container
Carefully screw the cap back on.
Usually, the salt warning light will be off in 2-6 days after the salt container be
filled with salt.
1. The salt container must be refilled when the salt warning li ght comes on. Though the salt container is filled
enough, the indicator light may not black out before the salt fully dissolve.
2. If there are spills of the salt, a soak program could be run to wipe them out.
The dishwasher is designed to allow for adjusting the amount of salt consum ed based on the hardness of the water used.
This is intended to optimize and customize the level of salt consumption so that the salt consumption could be set proceed as
Unscrew the cap from the salt container.
There is a ring on the container with an arrow on it (see Figure to the side), if
necessary, rotate the ring in the anticlockwise directi on from the "-" Setting
toward the "+" sign, based on the hardness of the water being used.It is
recommended that adjustments should be made in accordance with the following
Selector Position
Salt consumption
Auto nomy
Note:1 ° dH=1.25 ° Clark=1.78
° fH=0.178mmol/l
° dH : German degree
° fH : French degree
° Clark: British degree
Contact your local water board for information on the hardness of your water supply.
The dispenser must be refilled before the start of each wash cycle following the instructions provided i n the" Wash Cycle
Table".Your dishwashers use less detergent and rinse aid than conventional dishwashers. Generally, only one tablespoon of
detergent is needed for a normal wash load. Also, more heavily soiled items need more detergent. Always add the detergent just
before starting dishwasher, otherwise it could get damp and will not dissolve properly.
The amount of detergent needed can vary due to differences in water hardness. To determine the water hardness in your area,
contact your local water utility or area water softening company. The harder the water, the more detergent you may need.
Remember, you should adjust the amount of detergent you use by small amounts until you find the correct amount.
To remove hard water spots, try the following:
Run di shes through a normal wash program.
Remove all metal dishware, such as cutlery, pans, etc.,
from the dishwasher.
Do not add detergent.
Pour two cups of vinegar into a bowl and set the bowl face
up on the lower rack of the dishwasher.
Run the dishes through a normal wash program.
If this doesn't work, try the same process with 1 / 4 cup of
citric acid crystals instead of vinegar.
Use only detergent specifically made for use in dishwashers.
Keep your detergent fresh and dry. Don't put powder detergent
into the dispenser until You're ready to wash dishes.
Dishwasher detergent is corrosive! Take care to keep it out
of reach of children.
The rinse aid is released during the final rinse to prevent water
from forming droplets on your dishes that can leave spots and
streaks. It also improves drying by allowing water to "sheet" off
the dishes.
Your dishwashers are designed to use liquid rinse aids. The
rinse aid dispenser is located inside the door next to the
detergent dispenser. To fill the dispenser, open the cap and
pour the rinse aid into the dispenser until the level indicator
turns completely black. The volume of the rinse aid container is
about 140ml.
To open the dispenser, turn the cap to the "open" (left)
arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to
Replace the cap by inserting it aligned with "open" arrow
and turning it to the closed (right) arrow.
Be careful not to overfill the dispenser, because this could
cause oversudsing. Wipe away any spills with a damp cloth.
Don't forget to replace the cap before you close the dishwasher
If you have soft water, you may not need rinse aid for it may
cause a white film to develop on your dishes.
A measured amount of rinse aid is released during the final rinse. As with detergent, the amount
of rinse aid needed for your dishes depends on the hardness of the water in your area. Too much
rinse aid can result in lather of foaming and cause cloudiness or steaks on your dishes. If the
water in your area is very soft, you may not need rinse aid. If you do,you can dilute the rinse aid
with an equal amount of water.
The rinse aid dispenser has six settings. Always start with the dispenser set on " 2 ". If spots and
poor drying are problems, increase the amount of rinse aid dispensed by removing the dispenser
lid and rotating the dial to "3". If the dishes stil l are not drying properly or are spotted, adjust the
dial to the next higher number until your dishes are spot-free. We suggest you to set on "4" .
If there is no rinse aid warning light in the control panel, you can judge the amount of rinse aid by the following means. The
black dot on the rinse aid dispenser indicates the amount of rinse aid in the dispenser. As the rinse aid diminishes, the size of
the black dot decreases. You should never let the rinse aid get below 1 / 4 full.
As the rinse aid diminishes, the size of the black dot on the rinse
aid level indi cator changes, as illustrated below.
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to el iminate spotting
The upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cup and saucers, as well
as plates, small bowls and shallow pans(as long as they are not too dirty).
Position the dishes and cookware so that they do not get moved by the spray of water.
The upper rack can be adjusted for height by putting wheels of different height into the rails.
Small serving bowl
Large serving bowl
Dessert dishes
We recommend that you place large items which are most difficult to clean into the lower rack: pots, pans, lids,
serving dishes and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the
top spray arm.
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.
Dessert dishes
Oval platter
Dinner plates
Soup plates
Silverware basket
2 3 2
4 55 5
4 5 55
1 4
1 4
3 2 3
3 3 2
4 1 2
5 55 4
7 6 3
5 55 4
2 3 6
The filter prevent larger remnants of food or other objects from getting inside the pump. This residue can
occasionally clog up the filters.
The filter system consists of a coarse filter,a flat (Main filter) And a microfilter
(Fine filter).
Main filter
Food and soil particles trapped by this filter are pulverized by a special jet on the
lower spray arm and washed down the drain.
Coarse filter
Larger items, such as pieces of bone or glass, that could clog the drain are
trapped in the coarse filter. To remove an item caught in this filter, gently squee
ze the taps on the top of this filter and lift it out.
Fine filter
This filter holds soil and food residue in the sump area and prevents it from
being redeposit on the dishes during a cycle.
- Inspect the filters for obstructions every time the dishwasher has been used.
- By unscrewing the coarse can remove the filter system.Remove any food remnants and clean the
filters under running water.
step1:contrarotate the Coarse filter, step2:lift the Main filter up
step 3: lift the Fine filter up
and then lift it up;
NOTE:If do it from step1 to step 3, the filter system will be removed; while if do it from step3 to step 1, the filter system
will be installed.
If your dishwasher is left in an unheated place during the winter, ask a service technician to:
4 Reconnect the water inlet pipe to the
1 Cut off electrical power to the dishwasher.
water valve.
2 Turn off the water supply and disconnect the water
5 Remove the filter in the tub the bottom
inlet pipe from the water valve.
and use a sponge to soak up water
3 Drain water from the inlet pipe and water valve.
in sump.
(Use a pan to catch the water.)
Cleaning the Spray Arms
It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray arm jets and bearings.
Remove the upper spray arms
To remove the upper spray arms, screw off the nut clockwise to take out
the washer on top of the spray arm and remove the arm.
Remove the lower spray arms
To remove the lower spray arm, pull out the spray arm upward .
Wash the arms
Wash the arms in soapy and warm water and use a soft brush to clean
the jets. Replace them after rinsing them thoroughly.
Filter assembly
For best performance and results, the filter assembly must be cleaned.
The filter efficiently removes food particles from the wash water, allowing it to be
recirculated during the cycle. For this reason, it is a good idea to remove the larger
food particles trapped in the filter after each wash cycle by rinsing the semicircular
filter and cup under running water. To remove the filter assembly, pull on the cup
handle in the upward direction. The entire filter assembly should be cleaned
once a week.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemble
the filter parts as shown in the figures left and reinsert the entire assembly in the
dishwasher, positioning in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replaceme nt of the
filter may reduce the performance level of the appliance and damage dishes and utensils.
Never run the dishwasher without the filters in place.
To clean the edge around the door, you should use only a soft warm, damp rag. To prevent
penetration of water into the door lock and electrical components, do not use a spray cleaner
of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will
scratch the finish. Some papers towels can also scratch or leave marks on the surface.
Never use a spray cleaner to clean the door panel for it could damage the door l ock and electrical components. It is not allowed
to use the abrasive agent or some paper towel becauseof the risk of scratching or leaving spots on the stainless steel surface.
After every wash, turn off the water supply to the
appliance and leave the door slightly ajar so that
moisture and odors are not trapped inside.
When you go on holiday, it is recommened that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming
within the appl iance.
Before cleaning or performing maintenance, always
remove the plug from the socket. Do not run risks.
If the appliance must be moved, try to keep it in the vertical
position.If absolutely necessary, it can be positioned on
its back.
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Rather, use only a cloth and warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water and a little
white vinegar, or a cleaning product made specifically
for dishwashers.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning w ith a damp sponge will prevent this
from occurring.
Please see the rating lable to know the rating voltage and connect the dishwasher to appropriate power supply,Use required fuse
12 amp. Fused electrical supply is required-copper wire only. Time delay fuse or circuit breaker recommended and provide
separate circuit serving only this appliance. Outlet should be placed in adjacent cabinet.
After making sure that the voltage and the frequency values for the current in the home correspond to those
on the rating plate and that the electrical system is sized tor the maximum voltage on the rating plate, insert
the plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate tor the plug, replace the socket, rather than using a adaptors or the
like as they could cause overheating and burns.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is
fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water
run to make sure that the water is clear and free of impurities. If this precaution is not taken,
there is a risk that the water inlet can get blocked and damage the appliance.
The water supply to the appliance can also be connected to the house hot water line
(centralized system, heating system),as long as it does not exceed a temperature of 60 C.
In this case, the wash cycle time will be shortened by about 15 minutes and the wash
efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those
for the connection to the cold water line.
In order to avoid that there is more water
staying in the inlet hose,please close the hydrant
after using.(For the models: no safety inlet hose.)
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the
drain pump.
Some audible sounds are
Sound from soft food shredding action and detergent cup
Utensils are not secure
in the baskets or something
small has dropped into
the basket
To ensure everything is secured in the dishwasher.
Motor hums
Dishwasher has not been used regularly. If you do not use it
often, remember to set it to fill and pump out every week,
which will help keep the seal moist.
Improper detergent
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.
Spilled rinse agent
Always wipe up rinse agent
spills immediately.
Detergent with
colorant was used
Make sure that the detergent is the one without colorant.
Rinse agent dispenser
is empty
Make sure that the rinse agent dispense is filled.
Improper program
Select stronger program
Improper rack loading
Make sure that the action of the detergent dispenser and
spray arms are not blocked by large dishware.
Extremely hard water
Low inlet
Overloading the
Improper loading
Old or damp powder
Empty rinse agent
Incorrect dosage of
To remove spots from glassware:
Take out all metal utensils out of the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar
into the bottom of the dishwasher.
Close the door and let the dishwasher complete
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
crystals instead of vinegar.
Combination of soft
water and too much
Use less detergent if you have soft water and select a
shortest cycle to wash the glassware and to get them clean.
Tea or coffee stains
using a solution of 1/2 cup of bleach and 3 cups warm water
to remove the stains by hand.
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns
will happen.
Iron deposits in water
can cause an overall film
You have to call a water softener company for a special filter.
Hard water minerals
To clean the interior, use a damp sponge with dishwasher
detergent and wear rubber gloves. Never use any other cleaner
than dishwasher detergent for the risk of foaming or suds.
Dial is not in the OFF
Turn the Dial to OFF position and slide the door latch to the
Dishes block detergent
Re-loading the dishes properly.
Normal phenomenon
There is some steam coming through the vent by the door
latch during drying and water draining.
Aluminum utensils have
rubbed against dishes
Use a mild abrasive cleaner to eliminate those marks.
This is normal
A small amount of clean water around the outlet on
the tub bottom at the back of the tub keeps the water
seal lubricated.
Overfill dispenser or rinse
aid spills
Be careful not to overfill the rinse aid dispenser.
Spilled rinse aid could cause oversudsing and lead
to overflowing. Wipe away any spills with a damp cloth.
Dishwasher isn' t level
Make sure the dishwasher is level.
Download PDF