Built-in Outdoor Beverage Cooler
CBR1501SSOD
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage
cooler is designed for domestic use only. Do not use the unit for industrial or commercial use. Any other use may
invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other
technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
• Do not exceed the power outlet ratings.
• It is recommended the beverage cooler be
connected on its own circuit.
• The unit must be installed in accordance with
state and local electrical codes.
• A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
• Use outlets that cannot be turned off by a switch
or pull chain.
• Always turn the unit off and unplug it from the
outlet when cleaning.
• Unplug the unit if it is not going to be used for an
extended period of time.
• Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
• Be sure the beverage cooler is properly
grounded.
• Never plug or unplug the unit with wet hands.
• Do not bypass, cut or remove the grounding plug.
• Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
• Do not start or stop the unit by switching the
circuit’s power on and off.
• If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
• Never repair the unit while it is plugged in.
• Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
• Do not remove any part of the casing unless
instructed by an authorized technician.
• You should never attempt to repair the unit
yourself.
• Contact customer service for service options if the
unit needs service.
General Safety
• To prevent back and other types of injuries, use at
least two people to move and install the beverage
cooler.
• This unit is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
• Install the cooler in a well ventilated area where the
ambient temperature is above 50°F and below 95°F.
• The temperature range for this cooler is optimized
for beverage storage. Perishable food items may
require a different storage environment.
• Do not place hot or warm items into the cooler
before they cool down to room temperature.
• This unit is designed to be protected from rain, sleet,
snow, and/or moisture.
• This unit is not intended to be used by children.
• Children should be supervised to ensure that they
do not play with this product.
• Never allow children to crawl inside the beverage
cooler. If disposing the unit, remove the door.
• Do not use this cooler near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
• Do not place the unit near heat sources such as
ovens, grills, or direct sunlight.
• Only use in an upright position on a flat, level
surface and provide proper ventilation.
• Do not pinch or kink the power supply line between
the unit and cabinet.
• Do not leave any cleaning solutions in the unit
• Do not use solvent-based cleaning agents or
abrasive solutions to clean the unit as they may
damage the interior and exterior.
• Do not place any other appliances on top of the unit.
• Do not turn the unit upside down, on its side, or at
an angle off level.
• If your model cooler is equipped with a lock, take
care to keep the keys away from children.
• Do not move the unit without emptying the contents
and securing the door in a closed position.
i
NOTE: Flammable Refrigerant Used! When handling, moving and using the refrigerator: make sure to
avoid either damaging the refrigerant tubing, or increasing the risk of a leak.
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
BACK VIEW .......................................................................................................... 2
FRONT VIEW ........................................................................................................ 2
INSTALLING THE BEVERAGE COOLER ........................................................... 3
TYPES OF INSTALLATION....................................................................................... 3
Freestanding installation: .............................................................................. 3
Built-in installation: ........................................................................................ 3
INSTALLATION CLEARANCE REQUIREMENTS .......................................................... 4
ELECTRICAL REQUIREMENTS ................................................................................ 5
Recommended grounding method ................................................................ 5
LEVELING THE BEVERAGE COOLER ....................................................................... 5
INSTALLING THE DOOR HANDLE ............................................................................ 6
INSTALLING AND REMOVING THE SHELVES ............................................................ 6
REVERSING THE DOOR SWING.............................................................................. 7
OPERATION .......................................................................................................... 8
INSTALLATION CHECK LIST BEFORE OPERATION .................................................... 8
USING THE TEMPERATURE CONTROL PANEL ......................................................... 8
NORMAL SOUNDS ................................................................................................ 9
DEFROSTING ....................................................................................................... 9
PREPARING THE BEVERAGE COOLER FOR STORAGE .............................................. 9
CLEANING AND MAINTENANCE ...................................................................... 10
EXTERIOR CLEANING ......................................................................................... 10
INTERIOR CLEANING ........................................................................................... 10
TROUBLESHOOTING ........................................................................................ 10
TROUBLESHOOTING CONTINUED ......................................................................... 11
SPECIFICATIONS ............................................................................................... 12
First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from
the unit. Be sure to keep track of all included parts and pieces before discarding
packaging materials. It is advised that you keep the original box and packaging
materials in case you are ever to move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling
components time to settle from transit. The instruction manual should be read
before use.
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of your
beverage cooler for the latest technical information.
EdgeStar Built-in Beverage Cooler
ii
Introduction
Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose
us. We believe that your purchase of this product opens a relationship between
you and EdgeStar. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your beverage cooler. Following this manual will ensure that
your product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your beverage cooler.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
ratings label on the back of your unit and are needed to
obtain warranty service. You may also want to staple your
receipt to this manual as it is the proof of your purchase, and
is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1
•
If you received a damaged product, immediately contact the retailer or
dealer that sold you the product.
•
Read and follow this instruction manual carefully to help you install, use
and maintain your beverage cooler.
•
Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.
•
Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resources
and up-to-date information.
•
If you need warranty service, our friendly customer service
representatives are available via email at service@edgestar.com or by
telephone at 1 (866) 319-5473.
Parts Identification
Top Right Hinge
Front View
Control Panel
Internal Fan
Carbon Filter
Shelf
Door Handle
Stainless Steel Door
Note: The carbon filter
should be replaced
every 3-6 months
depending on the
unit’s exposure level
to odor. If the unit is
placed in the kitchen
regular replacement
every 3 months is
ideal.
Lock
Front vent
Leveling foot
** Can be replaced
with Casters for
mobility
Back View
Product Label
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
beverage cooler.
Power Plug
Cabinet
EdgeStar Built-in Beverage Cooler
2
Installing the Beverage Cooler
The beverage cooler should be installed in accordance with local
electrical code requirements. The beverage cooler should also be placed
in a location that is strong enough to support its total weight, keeping in
mind that it will weigh substantially more when fully loaded than when
empty.
Before you plug the beverage cooler into a power supply, be sure to let it
stand upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Beverage Cooler
WARNING: Use two more people to move and install the beverage
cooler. Failure to do so can result in back or other injury. Carefully remove
the packaging materials. Remove any shipping tape and glue from your
beverage cooler before using. Do not use sharp instruments, rubbing
alcohol, flammable fluids, or abrasive cleaners to remove tape or glue.
These products can damage the surface of your beverage cooler.
IMPORTANT: Do not remove any safety, warning, or product information
labels from your beverage cooler.
Types of Installation
This beverage cooler has been designed for freestanding, or built-in
installation. In every case, there must be adequate ventilation and access
for service.
Freestanding installation:
A free-standing installation will allow you to install the beverage cooler in
almost any place you desire. You must follow the stated instructions for
electrical requirements, and leveling the beverage cooler.
Built-in installation:
A recessed installation will allow you to install the beverage cooler under
a counter or in a kitchen cabinet provided the required clearance space
around the beverage cooler is followed.
It is necessary to allow adequate ventilation space around the unit (make
sure there is at least some ventilation room for the back of the unit). The
following additional items must be observed.
1. Place the beverage cooler in front of the installation location. Adjust
the feet and place the unit flat on the floor or on a platform depending
on your installation requirements.
2. If the electrical outlet for the beverage cooler is behind the cabinet,
plug in the beverage cooler.
3. Push the beverage cooler into position.
WARNING: Do NOT install the beverage cooler behind a closed cabinet
door.
3
Installation Clearance Requirements
When installing the beverage cooler under a counter, follow the
recommended spacing dimensions shown.
• To ensure proper service access and ventilation, allow at least 2” to 3”
clearance at the back. The installation should allow the unit to be pulled
forward for servicing, if necessary.
Important Notes:
• Choose a location that has
ambient temperatures above
50°F and below 95°F.
Operation outside these
temperatures may result in
lowered efficiency or cause
other adverse effects.
• This unit MUST be installed
in an area protected from the
elements, e.g., wind, rain,
water spray or drips.
• The beverage cooler should
not be located next to ovens,
grills or other high heat
sources.
• Do not kink or pinch the
power supply cord between
the beverage cooler and wall
or cabinet.
• The beverage cooler should be installed on a firm and level surface that
will be able to support the entire weight of a fully loaded unit. It is
important for the beverage cooler to be level in order to work properly. If
needed, you can adjust the height of the beverage cooler by rotating the
feet. See the “Leveling the Beverage cooler” section.
• A standard electrical supply (115 VAC only, 60 Hz), properly grounded
in accordance with National Electrical Code and local codes and
ordinances is required.
EdgeStar Built-in Beverage Cooler
4
Electrical Requirements
•
•
•
•
•
ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire,
electrical shock, or death.
Before you move your beverage cooler into its final location, it is
important to make sure you have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in
accordance with the National Electrical Code and local codes and
ordinances, is required.
It is recommended that a separate circuit, serving only your beverage
cooler, be provided. Use receptacles that cannot be turned off by a switch
or pull chain.
The fuse (or circuit breaker) size should be 3 Amps.
Recommended grounding method
For your personal safety, this appliance must be grounded. It is equipped
with a power supply cord having a 3-prong grounding plug. To minimize
possible shock hazard, the cord must be plugged into a mating 3-pronged
wall socket, and grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall socket is not
available, it is the personal responsibility of the customer to have a
properly grounded, 3-prong wall receptacle installed by a qualified
electrician.
Leveling the Beverage Cooler
It is important for the beverage cooler to be leveled in order to work
properly. It can be raised or lowered by rotating the plastic sheaths
around each of the feet on the bottom of the machine. If you find that the
surface is not level, rotate the feet until the beverage cooler becomes
level .You may need to make several adjustments to level it. We
recommend using a carpenter’s level to check the machine.
1. Place a carpenter’s level on top of the product to see if the beverage
cooler is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the refrigerator.
Turn the leveling feet to the left to raise that side of the refrigerator.
IMPORTANT: Once you are ready to install it in a cabinet or directly on
the floor, you must adjust the feet to level the beverage cooler.
5
Installing the Door Handle
To install the door handle:
1. Remove the four screws from the side of the door. This should
be the side opposite of the door hinge.
2. Place and align the openings of the handle hinges over the
screw holes.
3. Insert and tighten the screws to hold the handle in place.
CAUTION: Do not over-tighten the screws as this may cause
damage to the handle or to the stainless steel door.
Installing and Removing the Shelves
To prevent damaging the door gasket, make sure to open the door all the
way before pulling the shelves out of their track.
To install the shelves:
1. Open the door completely.
2. Slide the shelf on the shelf track and slowly push back until it stops.
3. Install the plastic notches.
To remove the shelves:
1. Open the door completely.
2. If necessary, make sure you remove all the contents sitting on the
shelf.
3. Remove both of the plastic notches with a screwdriver.
4. Continue to pull the shelf forward until it is completely removed from
the inner compartment.
EdgeStar Built-in Beverage Cooler
6
Reversing the Door Swing
Follow the instructions below to reverse the door swing.
IMPORTANT: Before you begin, unplug the refrigerator.
To reverse the door from right swing to left swing:
1. Open the door and using a Phillips screwdriver, remove the
bottom screws from the lower hinge.
2. Carefully slide the bottom of the door forward and down, and
place it on a padded surface to prevent damaging it.
3. Remove the screws from the upper right hinge. Place the upper
right hinge in a safe place in case you need to reverse the door in
the future. Remove the plastic caps from the upper left hinge
corner. Install the upper left hinge by fastening the screws through
the left hinge to the cabinet. Insert the plastic caps to the upper
right corner.
4. Remove the lower hinge and bushing from the bottom right
support bracket. Remove the decorative screws from the left corner
of the door and install and tighten them to the right corner holes.
Remove the plastic cap from the top left corner of the door and
insert it on the right top corner.
5. Install the lower hinge and bushing on the bottom left support
bracket
6. Carefully insert the door into the upper right corner hinge, then
slide the door on top of the lower hinge and secure the door by
installing the lower screws.
7
OPERATION
Installation Check List before Operation
1. Have all packing materials and tape been removed from the interior and
exterior of the beverage cooler?
2. Have the installation instructions been followed, including connecting the
machine to electricity? And has proper grounding been installed for the beverage
cooler?
3. Has the machine been leveled?
4. Is the beverage cooler in a site where the ambient temperature is between 50º
F and 95º F all year round?
5. Is there a clearance of at least 2 to 3” at the rear for proper air circulation?
Using the Temperature Control Panel
Run light
Set Display
Temp. Buttons
Temp. Scale Converter
Power Button
Current Temperature
Celsius and Fahrenheit Lights
Use the up and down buttons to adjust the temperature. The temperature
displayed can be in Fahrenheit or Celsius. This beverage cooler has a
temperature range from 38°F to 50°F.
Note: Whether your
beverage cooler can reach
the actual set temperature
depends on the ambient
environmental conditions.
This beverage cooler has two displays, a Set Display that shows the set
temperature, and a Current Temperature Display that shows the current
temperature. Note: It is normal to see the set temperature and current
temperature displays being a few degrees off from each other.
Press the
button on the control panel to lower the temperature by 1
degree increments.
Allow at least 24 hours before storing your beverages and to allow the
temperature to acclimate.
Press the
button on the control panel to increase the temperature by 1
degree increments.
Caution: If you powered off
the unit, please wait at least
5 minutes before powering it
back on.
Press and hold the power button for approximately 3 seconds to turn the
unit’s power on or off. The Run Light will illuminate when the unit is
working.
The Celsius or Fahrenheit light will be lit depending on what scale
temperature is being displayed. To switch between C and F, press the
˚C/˚F button.
EdgeStar Built-in Beverage Cooler
8
Normal Sounds
Your new beverage cooler may make sounds that are not familiar to
you. Most of the new sounds are normal. Hard surfaces like the
floor, walls can make the sounds seem louder than they actually
are. The following describes the kinds of sounds that might be new
to you and what may be making them.
• Rattling noises may come from the flow of the refrigerant or the
water line, Items stored on top of the beverage cooler can also
make noises.
• The high efficiency compressor may make a pulsating or highpitched sound.
• Water running from the evaporator to the water bin may make a
splashing sound.
• As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your beverage cooler.
• You may hear air being forced over the condenser by the
condenser fan.
Defrosting
Note that under most refrigerating settings, the unit will
automatically defrost under most ambient conditions. However, on
colder settings, some frost may build up. Additionally, the more
humid the ambient conditions, the more frost may build up. Keep
the door closed as much as possible and avoid opening the door
unnecessarily to minimize frost build-up.
If frost is preventing the door from closing properly, you may need
to power the unit off until the frost melts. Use a soft absorbent towel
to dry the unit.
WARNING: Never attempt to remove frost with a sharp object!
Preparing the Beverage cooler for Storage
If the beverage cooler will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit and
dry the interior.
IMPORTANT:
1. Disconnect the cooler from the power supply by removing the
power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent
mold, mildew and unpleasant smells.
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
CAUTION: Store the unit out of the reach of children. If you have
children, you may want to take additional precautions such as
removing the door to prevent a child from being trapped inside the
cooler!
9
CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, top
performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and
lukewarm water solution such as 2 tablespoons of baking soda to 1 quart
of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and
rinse with clean water. Wipe with a soft clean towel to prevent water
spotting. If the door panel is stainless steel, it can discolor when exposed
to chlorine gas and moisture. Clean stainless steel with a cloth dampened
with a mild detergent and warm water solution. Never use an abrasive or
caustic cleaning agent.
Interior Cleaning
The beverage cooler’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.
TROUBLESHOOTING
Before Calling for Help
If the unit appears to be malfunctioning, read through the OPERATION
section of this manual first. If the problem persists, check the
Troubleshooting Guide below and on the following page. The problem
could be something that can easily be solved or explained.
Symptoms
The beverage cooler
turns on and off
frequently.
Possible causes
Solutions
The room temperature is
higher than the
recommended ambient
environment.
Run the cooler at the appropriate ambient temperature.
The door is being opened
often.
Minimize the number of times the door is opened.
The door is not completely
closed.
Make sure the door is completely closed.
The door gasket is not
sealing properly.
Make sure the door gasket is properly sealing.
The cooler does not have the
suggested ventilation.
Read and follow the “Installation Clearance
Requirements” section.
EdgeStar Built-in Beverage Cooler
10
Troubleshooting continued
Issue
The beverage cooler
does not turn on.
The beverage cooler will
not reach the desired
temperature
Possible cause
Solution
There is a power failure.
Ensure the cooler is plugged in and the power outlet has
power.
The cooler is not plugged in.
Plug the unit in to a power outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse box or reset the
breaker.
The cooler is placed too
close to a heat source.
Keep the cooler away from direct sun light or other heat
sources.
The cooler does not have
sufficient ventilation.
Read and follow the “Installation Clearance Requirements”
section.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open the door too
frequently or for a long period of time.
Certain sounds are normal.
Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the cooler is level, and that it is
not in contact with another appliance or furniture.
The unit is not grounded
properly.
Contact your local electrician to test your electrical
grounding system.
The environment is humid.
Though the unit uses an “auto-defrost” system, under
certain conditions, manual defrosting may be required. If
frost builds up, you can try running the cooler on a warmer
temperature setting, minimizing the number of times you
open the door, or unplugging the unit to allow the frost to
melt.
The beverage cooler is
making strange noises
The body of the beverage
cooler is electrified.
Frost is forming in the
beverage cooler.
The ambient temperature is
too low.
The door is being opened
too frequently.
Your cooler is not level.
The door gasket is dirty.
The door will not shut
properly.
11
Make sure the cooler is on a level surface.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is properly installed.
The shelves are incorrectly
installed.
Correctly install the shelves.
Specifications
Description of product
Built-in Beverage Cooler
Model
CBR1501SSOD
Voltage/Frequency
AC 115V~60Hz
Amperage
1.1A
Input Power
120W
Color
Stainless Steel Cabinet;
Stainless Steel Door
Storage Capacity
142 Cans*
Refrigerant
R600a, 1.4 oz.
Temperature Range
38 - 50ºF
Dimensions
(Height x Width x Depth )
33 1/2” x 23 1/2” x 24 3/4”
Weight
101 pounds
Note: Technical data and performance information is provided for
reference only.
Specifications are subject to change. Check the rating label on the
beverage cooler for the most accurate information.
*Note on beverage storage capacity:
The beverage cooler can store 142 standard 12 oz. cans.
EdgeStar Built-in Beverage Cooler
12
Limited Warranty: Full One-Year Parts and Labor
This product is warranted by EdgeStar and is subject to any conditions set forth as follows:
WHAT IS COVERED:
For a period of ONE (1) YEAR from the date of
original retail purchase, EdgeStar will repair or
replace any part free of charge including labor
that fails due to a defect in materials or
workmanship. Labor will be performed free of
charge at an authorized EdgeStar repair facility
and EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may
request a defective part be returned in
exchange for the replacement part. All
replacement parts or products will be new,
remanufactured, or refurbished. All products and
parts replaced by EdgeStar under warranty
service become the property of EdgeStar. After
the 12 month period, EdgeStar will no longer be
responsible for labor charges incurred or
replacement parts. All defective products and
parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar
authorized repair facility.
This warranty applies to the original purchaser
only, and only covers defects in workmanship
experienced during operation of the product
under normal service, maintenance, and usage
conditions. This warranty applies to the purchase
and use of this product in residential settings
within the United
States of America.
Exceptions: Commercial or Rental Use
Warranty
90 days labor and parts from date of original
purchase. No other warranty applies.
WHAT IS NOT COVERED- The following limitations apply to the
coverage of this warranty. This warranty does not cover:
-Labor charges for installation, setup or training to use the
product.
-Shipping damage, and any damage caused by improper
packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse,
including abnormal service, handling, or usage.
-Cosmetic damage such as scratches and dents.
-Normal wear and tear on parts or replacement of parts designed
to be replaced, e.g. filters, cartridges, batteries.
-Service trips to deliver, pick-up, or repair, install the product, or to
instruct in proper usage of the product.
-Damages or operating problems resulting from misuse, abuse,
operation outside environmental specifications, uses contrary to
instructions provided in the owner’s manual, accidents, acts of
God, vermin, fire, flood, improper installation, unauthorized
service, maintenance negligence, unauthorized installation or
modification, or commercial use.
-Labor, service transportation, and shipping charges for the
removal and replacement of defective parts, beyond the initial 12
month period.
-Products that have been modified to perform outside of
specifications without the prior written permission of EdgeStar.
-Products lost in shipment, or theft.
-Products sold AS IS or from an unauthorized reseller.
-Products that have had their serial numbers removed, defaced,
or with serial numbers that have been invalidated.
-Damage from other than normal household use.
-Replacement or repair of household fuses, circuit breakers, wiring
or plumbing.
-Damage to personal property from use of product.
-Damage from service other than from an authorized EdgeStar
repair facility.
-Hoses, knobs, lint trays and all attachments, accessories and
disposable parts.
-Any service charges not specifically identified as normal such as
normal service area or hours.
-Any special or consequential damages arising out of the use of
the product.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for
troubleshooting assistance and warranty service at www.edgestar.com or call 1-866-319-5473. Before contacting
Customer Support you are required to have your model number, serial number and proof of purchase available upon
request. Once an EdgeStar authorized representative has confirmed that your product is defective and eligible for
warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar is not responsible for
damage resulting from shipper mishandling or improper packaging. Do not return a defective product to the place of
purchase. Products received without a return authorization number will be refused.
THISWARRANTYISINLIEUOFANYOTHERWARRANTY,EXPRESSORIMPLIED,INCLUDINGWITHOUTLIMITATION,ANYWARRANTYOFMERCHANTABILITYOR
FITNESSFORAPARTICULARPURPOSE.TOTHEEXTENTANYIMPLIEDWARRANTYISREQUIREDBYLAW,ITISLIMITEDINDURATIONTOTHEEXPRESSWARRANTY
PERIODABOVE.NEITHERTHEMANUFACTURERNORITSDISTRIBUTORSSHALLBELIABLEFORANYINCIDENTAL,CONSEQUENTIAL,INDIRECT,SPECIAL,OR
PUNITIVEDAMAGESOFANYNATURE,INCLUDINGWITHOUTLIMITATION,LOSTREVENUESORPROFITS,ORANYOTHERDAMAGEWHETHERBASEDIN
CONTRACT,TORT,OROTHERWISE.SOMESTATESDONOTALLOWTHEEXCLUSIONOFINCIDENTALORCONSEQUENTIALDAMAGES,SOTHEABOVEEXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
Register your product, download owner’s manuals, access additional troubleshooting
resources, and obtain more information on other great EdgeStar products on the web at:
http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2014 Living Direct, Inc. All rights reserved.
Download PDF

advertising