installation instructions 30"

INSTALLATION INSTRUCTIONS
30" (76 CM) FREESTANDING ELECTRIC RANGES
Table of Contents
RANGE SAFETY..............................................................................1
INSTALLATION REQUIREMENTS ................................................2
Tools and Parts ............................................................................2
Location Requirements ................................................................2
Electrical Requirements ...............................................................3
INSTALLATION INSTRUCTIONS ..................................................4
Unpack Range..............................................................................4
Install Anti-Tip Bracket .................................................................5
Electrical Connection - U.S.A. Only .............................................6
Verify Anti-Tip Bracket Location ..................................................9
Level Range..................................................................................9
Complete Installation..................................................................10
Moving the Range ......................................................................10
ANTI-TIP BRACKET TEMPLATE ...............................................11
RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
DANGER
WARNING
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.
IMPORTANT:
Save installation instructions for local electrical inspector's use.
9762996A
INSTALLATION REQUIREMENTS
■
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
■
The floor anti-tip bracket must be installed. To install the antitip bracket shipped with the range, see “Install Anti-Tip
Bracket” section.
Tools needed
■
Grounded electrical supply is required. See “Electrical
Requirements” section.
Tools and Parts
■
Tape measure
■
³⁄₈" drive ratchet
■
Flat-blade screwdriver
■
¼" nut driver
■
Level
■
³⁄₈" and ⁵⁄₁₆" nut driver
■
Hammer
■
■
Hand or electric drill
¹⁄₈" (3.2 mm) drill bit (for
wood floors)
■
Wrench or pliers
■
■
Marker or pencil
³⁄₁₆" (4.8 mm) carbide-tipped
masonry drill bit (for
concrete/ceramic floors)
■
Masking tape
Parts supplied
Check that all parts are included.
A
B
IMPORTANT: Some cabinet and building materials are not
designed to withstand the heat produced by the oven for baking
and self-cleaning. Check with your builder or cabinet supplier to
make sure that the materials used will not discolor, delaminate or
sustain other damage.
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or local codes.
Mobile home installations require:
■ When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
■
C
Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See “Electrical Connection” section.
Product Dimensions
A. Anti-tip bracket
B. Plastic anchors (2)
C. #10 x 1¹⁄₂" screws (2)
■
Anti-tip brackets must be securely mounted to subfloor.
Thickness of flooring may require longer screws to anchor
bracket to subfloor. Longer screws are available from your
local hardware store.
A
Parts needed
Check local codes. Check existing electrical supply. See
“Electrical Requirements” section.
All electrical connections should be made by a licensed, qualified
electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
■ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the left side frame
behind the storage drawer panel.
■
■
2
The range should be located for convenient use in the
kitchen.
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
B
C
F
E
D
A. 27¹⁄₈" (68.9 cm) depth with handle
28¹⁄₈" (71.6 cm) depth with handle (KitchenAid models only)
B. 46⁷⁄₈" (119.1 cm) overall height
46" (116.8 cm) overall height (KitchenAid models only)
C. 36" (91.4 cm) cooktop height
D. 29⁷⁄₈" (75.9 cm) width
E. 24¹³⁄₁₆" (63 cm) depth
F. Model/serial rating plate (located on the left side frame behind
storage drawer panel)
Installation Clearances
Electrical Requirements
Cabinet opening dimensions shown are for 25" (64 cm)
countertop depth, 24" (61 cm) base cabinet depth and
36" (91.4 cm) countertop height.
C
E
E
D
B
F
A
G
H
A. 4" (10.2 cm) min. clearance from both sides of range to side wall
or other combustible material
B. 18" (45.7 cm) upper side cabinet to countertop
C. 13" (33 cm) max. upper cabinet depth
D. 30" (76.2 cm) min. opening width
E. For minimum clearance to top of cooktop, see NOTE*.
F. 30" (76.2 cm) min. opening width
G. Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,
5¹⁄₂" (14.0 cm) max. from floor
H. ⁷⁄₈" (2.2 cm) min. required between cutout and cabinet door or
hinge.
*NOTE: 24" (61 cm) minimum when bottom of wood or metal
cabinet is protected by not less than ¹⁄₄" (0.64 cm) flame
retardant millboard covered with not less than No. 28 MSG
sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the
cooking platform and the bottom of an unprotected wood or
metal cabinet.
If installing a range hood or microwave hood combination above
the range, follow the range hood or microwave hood
combination installation instructions for dimensional clearances
above the cooktop surface.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
codes.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or service technician if you are in doubt as to
whether the appliance is properly grounded. Do not modify the
power supply cord plug. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
This range is manufactured with the neutral terminal connected
to the cabinet. Use a 3-wire, UL listed, 40 or 50 amp power
supply cord (pigtail); or if local codes do not permit ground
through the neutral, use a 4-wire power supply cord rated at
250 volts, 40- or 50-amps and investigated for use with ranges.
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
■ Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating
plate. The model/serial number rating plate is located on the
oven frame behind the storage drawer panel. Refer to the
figures in the “Product Dimensions” section of the “Location
Requirements” section.
■
When a 4-wire or 3-wire, single phase 120/240 volt, 60 Hz,
AC only electrical supply is available, a 50-amp maximum
circuit protection is required (or, if specified on the model/
serial rating plate, when a 4-wire or 3-wire single phase
120/208 volt 60 Hz, AC only electrical supply is available, a
40- or 50-amp maximum circuit protection is required), fused
on both sides of the line.
■
A time-delay fuse or circuit breaker is recommended.
■
The range can be connected directly to the fused disconnect
(or circuit breaker box) through flexible or nonmetallic
sheathed, copper or aluminum cable. See “Electrical
Connection.”
■
Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that
the range can be moved if servicing is ever necessary.
■
A UL listed conduit connector must be provided at each end
of the power supply cable (at the range and at the junction
box).
■
Wire sizes and connections must conform with the rating of
the range.
■
The wiring diagram is located on the back of the range or
inside the storage drawer in a clear plastic bag.
3
If connecting to a 4-wire system:
This range is manufactured with the ground connected to the
cabinet. The ground must be revised so the green ground wire of
the 4-wire power supply cord is connected to the cabinet. See
“Electrical Connection.”
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power
supply cord (pigtail) must be used. This cord contains 4 copper
conductors with ring terminals or open-end spade terminals with
upturned ends, terminating in a NEMA Type 14-50R plug on the
supply end.
The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
and be at least 4 ft (1.22 m) long.
The minimum conductor sized for the copper 4-wire power
cord are:
40-amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-8 green grounding
If connecting to a 3-wire system:
Local codes may permit the use of a UL listed, 3-wire, 250-volt,
40- or 50-amp range power supply cord (pigtail). This cord
contains 3 copper conductors with ring terminals or open-end
spade terminals with upturned ends, terminating in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.
3-wire receptacle (10-50R)
4-wire receptacle (14-50R)
INSTALLATION INSTRUCTIONS
Unpack Range
WARNING
Excessive Weight Hazard
3. On Ranges Equipped with Storage Drawers:
Remove the storage drawer. Use a ³⁄₈" drive ratchet to lower
the rear leveling legs one-half turn. Use a wrench or pliers to
lower front leveling legs one-half turn.
A
Use two or more people to move and install range.
D
Failure to do so can result in back or other injury.
1. Remove shipping materials, tape and protective film from
range. Remove oven racks and parts package from inside
oven.
2. Do not remove the shipping base at this time.
C
B
A. ³⁄₈" drive ratchet
B. Rear leveling leg
C. Wrench or pliers
D. Front leveling leg
On Ranges Equipped with Warming Drawers:
A
A. Shipping base
Use a wrench or pliers to lower the front and rear leveling legs
one-half turn.
A
B
C
A. Rear leveling leg
B. Front leveling leg
C. Wrench or pliers
4
Install Anti-Tip Bracket
WARNING
To mount anti-tip bracket to concrete or ceramic floor, use a
³⁄₁₆" (4.8 mm) masonry drill bit to drill 2 holes at the positions
marked on the bracket template. Remove template from floor.
6. Tap plastic anchors into holes with a hammer.
7. Align anti-tip bracket holes with holes in floor. Fasten anti-tip
bracket with screws provided.
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
Contact a qualified floor covering installer for the best procedure
for drilling mounting holes through your type of floor covering.
Before moving range, slide range onto shipping base, cardboard
or hardboard.
1. Remove template from the anti-tip bracket kit (found inside
the oven cavity) or from the back of this manual.
2. Place template on the floor in cabinet opening so that the left
edge is against cabinet and top edge is against rear wall,
molding or cabinet.
3. Tape template into place.
4. If countertop is not flush with cabinet opening edge, align
template with overhang.
Depending on the thickness of your flooring, longer screws
may be necessary to anchor the bracket to the subfloor.
Longer screws are available from your local hardware store.
8. Move range close enough to opening to allow for electrical
connections to be made. Remove shipping base, cardboard
or hardboard from under range.
9. Make electrical connections as described in the “Electrical
Connection” section.
10. Move range into its final location making sure rear leveling leg
slides into anti-tip bracket.
11. If installing the range in a mobile home, you must secure the
range to the floor. Any method of securing the range is
adequate as long as it conforms to the standards in the
“Location Requirements” section.
12. Continue installing your range using the following installation
instructions.
If cabinet opening is wider than that specified in the “Location
Requirements” section, adjust template so range will be
centered in cabinet opening.
5. To mount anti-tip bracket to wood floor, drill two ¹⁄₈" (3.2 mm)
holes at the positions marked on the bracket template.
Remove template from floor.
5
Electrical Connection - U.S.A. Only
Power Supply Cord
Direct Wire
WARNING
WARNING
Electrical Shock Hazard
Electrical Shock Hazard
Disconnect power before servicing.
Disconnect power before servicing.
Use a new 40 amp power supply cord.
Use 8 gauge copper or 6 gauge aluminum wire.
Plug into a grounded outlet.
Electrically ground range.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Disconnect power.
2. Remove the terminal block cover screws located on the back
of the range. Pull cover down and toward you to remove
cover from range.
3. Add strain relief.
Style 1: Power supply cord strain relief
■
Remove the knockout for the power supply cord.
■
Assemble a UL listed strain relief in the opening.
A
B
A
A. UL listed strain relief
■
C
A. Two mounting tabs each side
B. Terminal block cover
C. Hex-head screws
6
Tighten strain relief screw against the power supply cord.
Style 2: Direct wire strain relief
■
Remove the knockout as needed for the flexible conduit
connection.
■
Assemble a UL listed conduit connector in the opening.
A
4-wire connection: Power supply cord
Use this method for:
■ New branch-circuit installations (1996 NEC)
■
Mobile homes
■
Recreational vehicles
■
In an area where local codes prohibit grounding through the
neutral
1. Remove the ground-link screw from the range frame. Save
the ground link screw and cup washer. Bend the ground-link
away from the range so that it does not contact the range.
B
A. Removable retaining nut
B. Strain relief
■
C
Tighten strain relief screw against the flexible conduit.
B
A
A. Ground-link screw
B. Cup washer
C. Ground-link bent away from range
4. Complete installation following instructions for your type of
electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
Electrical Connection Options
If your home has:
4-wire receptacle
(NEMA type 14-50R)
And you will be
connecting to:
Go to Section:
A UL listed,
250-volt
minimum,
40-amp, range
power supply
cord
4-wire connection:
Power supply cord
2. Connect the green ground wire from the power supply cord to
the range using the ground-link screw and cup washer. The
ground wire must be attached first and must not contact any
other terminal.
3. Use a ¼" nut driver to remove the hex washer head screws
from the terminal blocks.
4. Connect the neutral (center) wire to the center terminal
connector using one of the hex washer head screws.
Securely tighten screw for proper electrical connection.
E
D
F
C
B
G
H
4-wire direct
5"
(12.7 cm)
3-wire receptacle
(NEMA type 10-50R)
3-wire direct
1"
(2.5 cm)
A fused
disconnect or
circuit breaker
box
4-wire connection:
Direct wire
A UL listed,
250-volt
minimum,
40-amp, range
power supply
cord
3-wire connection:
Power supply cord
A fused
disconnect or
circuit breaker
box
3-wire connection:
Direct wire
A
I
A. Line 1
B. Green ground wire
C. Ground-link screw
D. Hex washer head
screw
E. Silver-colored terminal
block screw
F. Ground-link
G. Neutral (center) wire
H. Line 2
I. UL listed strain relief
and 40- or 50-amp
range power supply
cord
5. Connect the other 2 wires (lines 1 and 2) to the outer
aluminum terminal blocks.
6. Securely tighten screws for proper electrical connection.
7. Tighten strain relief screws.
8. Replace terminal block cover.
3"
(7.6 cm)
7
■
3-wire connection: Power supply cord
Use this method only if local codes permit connecting cabinetground conductor to neutral wire of power supply cord.
1. Use a ¼" nut driver and remove the hex washer head screws
from the aluminum terminal blocks.
2. Connect the neutral (center) wire to the center terminal
connector using one of the hex washer head screws.
Securely tighten screw for proper electrical connection.
In an area where local codes prohibit grounding through the
neutral
1. Remove the ground-link screw from the range frame. Save
the ground-link screw and cup washer. Bend the ground-link
away from the range so that it does not contact the range.
C
D
B
C
A
E
B
F
A
A. Ground-link screw
B. Cup washer
C. Ground-link bent away from range
2. Connect the bare ground wire to the range using the groundlink screw and cup washer. The ground wire must be
attached first and must not contact any other terminal.
G
D
A. Line 1
B. Ground-link
C. Hex washer head screw
D. Silver-colored terminal
block screw
E. Neutral (center) wire
F. Line 2
G. UL listed strain relief
and 40- or 50-amp range
power supply cord
C
E
F
B
3. Connect the other 2 wires (lines 1 and 2) to the outer terminal
screws on the terminal block.
4. Tighten strain relief screws.
5. Replace terminal block cover.
Direct Wire Installation: Copper or Aluminum Wire
This range may be connected directly to the fuse disconnect or
circuit breaker box. Depending on your electrical supply, make
the required 3-wire or 4-wire connection.
1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip
the insulation back 1" (2.5 cm) from the end of each wire.
1"
(2.5 cm)
G
A
A. Bare wire from power
supply cable
B. Line 1
C. Hex washer head screw
D. Silver-colored terminal
block screw
3. Loosen (do not remove) the hex washer head screw and
insert the neutral (white) wire under the screw clamp at the
bottom of the center position terminal connector.
4. Insert the other 2 wires (lines 1 and 2) under the other 2 screw
clamps.
3"
(7.6 cm)
2. Allow enough slack in the wire to easily attach the wiring
terminal block.
3. Complete electrical connection according to your type
electrical supply (4-wire or 3-wire electrical connection).
4-wire connection: Direct wire
Use this method for:
■ New branch-circuit installations (1996 NEC)
■
Mobile homes
■
Recreational vehicles
8
E. Line 2
F. Neutral (white) wire
G. UL listed strain relief and
power supply cable
B
A
A. Insert wire under screw clamp.
B. Hex washer head screw
5. Securely tighten the hex washer head screws to
35 lbs-in. (4.0 N-m) minimum torque to make proper
electrical connection.
6. Tighten the locking ring of the conduit connector.
7. Replace the terminal block cover.
3-wire connection: Direct wire
Verify Anti-Tip Bracket Location
Use this method only if local codes permit connecting ground
conductor to neutral supply wire.
1. Loosen (do not remove) the hex washer head screws and
insert the neutral (white) wire under the screw clamp at the
bottom of the center position terminal connector.
1. Pull drawer open to first stop position. Lift front of drawer to
clear white wheels in drawer guides. Remove drawer and set
it aside on a protected surface.
D
C
E
F
B
G
2. Making sure the anti-tip bracket is installed:
■ Look for the anti-tip bracket securely attached to floor.
■
A
A. Line 1
B. Ground-link
C. Hex washer head screw
D. Silver-colored terminal
block screw
E. Neutral (white) wire
F. Line 2
G. UL listed strain relief
and power supply
cable
2. Insert the other 2 wires (lines 1 and 2) under the other 2 screw
clamps.
Slide range back so rear range foot is under anti-tip
bracket.
3. If installing the range in a mobile home, you must secure the
range to the floor. Any method of securing the range is
adequate as long as it conforms to the standards in the
“Location Requirements” section.
Level Range
B
1. Place rack in oven. Place level on rack and check levelness of
range, first side to side; then front to back.
A
A. Insert wire under screw clamp.
B. Hex washer head screw
3. Securely tighten the hex washer head screws to
35 lbs-in. (4.0 N-m) minimum torque to make a proper
electrical connection.
4. Tighten the locking ring of the conduit connector.
5. Replace the terminal block cover.
If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.
On Ranges Equipped with Storage Drawers:
Use ³⁄₈" drive ratchet and channel lock pliers to adjust leveling
legs up or down until range is level. Push range back into
position. Check that rear leveling leg is engaged in anti-tip
bracket.
On Ranges Equipped with Warming Drawers:
Use channel lock pliers to adjust leveling legs up or down
until range is level. Push range back into position. Check that
rear leveling leg is engaged in anti-tip bracket.
NOTE: Range must be level for satisfactory baking
conditions.
2. Replace the storage drawer (and warming drawer on some
models).
9
For power supply cord-connected ranges:
Complete Installation
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check that the range is level. See “Level Range.”
5. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by protective shipping
material. Dry thoroughly with a soft cloth. For more
information, read the “Range Care” section of the Use and
Care Guide.
6. Read “Range Use” in the range Use and Care Guide.
7. Plug power cord into appropriate outlet. Turn power on.
8. Turn on surface burners and oven. See the Use and Care
Guide for specific instruction on range operation.
If range does not operate, check the following:
■ Household fuse is intact and tight; or circuit breaker has not
tripped.
■
Range is plugged into an outlet.
■
Electrical supply is connected.
■
See “Troubleshooting” in the Use and Care Guide.
1. Unplug the power supply cord.
2. Slide range forward to complete cleaning or maintenance.
3. Check that anti-tip bracket is installed:
■ Look for the anti-tip bracket securely attached to floor.
■
4. Check that range is level.
For direct-wired ranges:
WARNING
When the range has been on for 5 minutes, check for heat. If
range is cold, turn off the range and contact a qualified
technician.
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Moving the Range
WARNING
Slide range back so rear range foot is under anti-tip
bracket.
Failure to do so can result in death or electrical shock.
1.
2.
3.
4.
Disconnect power.
Disconnect wiring.
Slide range forward to complete cleaning or maintenance.
Check that anti-tip bracket is installed:
■ Look for the anti-tip bracket securely attached to floor.
■
Slide range back so rear range foot is under anti-tip
bracket.
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
When moving range, slide range onto cardboard or hardboard to
avoid damaging the floor covering.
If removing the range is necessary for cleaning or maintenance:
10
5. Check that range is level.
ANTI-TIP BRACKET TEMPLATE
Cut on dotted lines and place the left edge against the left side cabinet and the top edge against the rear wall.
Left edge
Top edge
11
9762996A
© 2006.
All rights reserved.
8/06
Printed in U.S.A.