5713222811/02.14
De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com
ECAM45.76X
BEAN TO CUP ESPRESSO
AND CAPPUCCINO
MACHINE
Instruction for use
EN page 6
B
B15
B14
B13
B12
B11
B1
B10
B2
B3
B4
B5
B6
C
B7
B8
B9
D
D1
C1
D2
C2
D4
D3
D5
C3
C5
C4
D7
D6
D8
2
A1
A20
A19
A2
A3
A5
A4
A6
B
A7
A8
A15
A14
A9
A18
A10
A17
A11
A12
A13
3
A16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
MIL
K
18
17
19
20
23
24
27B
28
31
32
A
B
21
22
25
26
29
30
27A
5
CONTENTS
Making LONG coffee using pre-ground coffee................. 13
Customising the LONG coffee quantity ........................... 13
INTRODUCTION.................................................7
MAKING CAPPUCCINOS AND MILK BASED
COFFEES.......................................................... 13
Symbols used in these instructions................................... 7
Letters in brackets............................................................. 7
Troubleshooting and repairs............................................. 7
Filling and attaching the milk container......................... 13
Adjusting the amount of froth........................................ 14
Making milk based coffees automatically....................... 14
Making hot drinks using the “MILK MENU”...................... 14
Cleaning the milk container after use............................. 14
Programming the quantity of coffee and milk in the cup for
the CAPPUCCINO, CAFFELATTE and MACCHIATO buttons.......15
Programming the quantity of coffee and milk in the cup
for the MILK MENU button drinks.................................... 15
SAFETY.............................................................7
Fundamental safety warnings.......................................... 7
Designated use................................................................. 7
Instruction for Use............................................................ 8
DESCRIPTION....................................................8
Description of the appliance ............................................. 8
Description of the milk container...................................... 8
Description of the accessories........................................... 8
DELIVERING HOT WATER AND STEAM................ 15
BEFORE USE......................................................8
Checking the appliance..................................................... 8
Installing the appliance.................................................... 9
Setting up the appliance................................................... 9
Using the appliance for the first time................................ 9
Delivering hot water ...................................................... 15
Changing the quantity of water delivered automatically.15
Delivering steam............................................................. 15
Tips for using steam to froth milk.................................... 15
Cleaning the spout after use........................................... 16
TURNING THE APPLIANCE ON.............................9
CLEANING....................................................... 16
Cleaning the machine..................................................... 16
Cleaning the coffee grounds container............................ 16
Cleaning the drip tray and condensate tray..................... 16
Cleaning the inside of the coffee machine...................... 16
Cleaning the water tank.................................................. 17
Cleaning the coffee spouts.............................................. 17
Cleaning the pre-ground coffee funnel........................... 17
Cleaning the infuser........................................................ 17
Cleaning the milk container............................................ 18
Cleaning the hot water/steam connection nozzle........... 18
TURNING THE APPLIANCE OFF............................9
MENU SETTINGS.............................................. 10
Rinsing............................................................................ 10
Descaling........................................................................ 10
Install filter..................................................................... 10
Replacing the filter (if installed)..................................... 10
Adjust time..................................................................... 10
Auto-start....................................................................... 10
Auto-Off (standby).......................................................... 10
Cup warmer ................................................................... 10
Energy saving.................................................................. 11
Setting the temperature ................................................ 11
Setting water hardness................................................... 11
Setting the language ..................................................... 11
Beep............................................................................... 11
Default values (reset)...................................................... 11
Statistics function........................................................... 11
DESCALING...................................................... 18
SETTING WATER HARDNESS.............................. 19
Measuring water hardness.............................................. 19
Setting water hardness................................................... 19
WATER SOFTENER FILTER................................. 19
Installing the filter.......................................................... 19
Replacing the filter......................................................... 20
Removing the filter......................................................... 20
MAKING COFFEE.............................................. 12
Selecting the coffee taste................................................ 12
Selecting the quantity of coffee in the cup ..................... 12
Customising the “my coffee” quantity ............................. 12
Adjusting the coffee mill................................................. 12
Tips for a hotter coffee.................................................... 12
Making coffee using coffee beans................................... 12
Making coffee using pre-ground coffee.......................... 13
Making LONG coffee using coffee beans.......................... 13
TECHNICAL DATA............................................. 20
DISPLAYED MESSAGES..................................... 21
TROUBLESHOOTING......................................... 22
DISPOSAL........................................................ 23
ELECTRICAL CONNECTION (UK ONLY)................. 24
6
INTRODUCTION
• Unplug directly from the plug only. Never pull the power
cable as you could damage it.
• To disconnect the appliance completely, unplug it from the
mains socket.
• If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact Customer Services.
Symbols used in these instructions
If the plug or power cable is damaged, it
must be replaced by De’Longhi Customer
Services only to avoid all risk.
Never immerse the appliance in water when
cleaning. It is an electrical appliance.
Thank you for choosing this automatic espresso and cappuccino
machine.
We hope you enjoy using your new appliance.
Take a few minutes to read this Instruction for Use.
This will avoid all risks and damage to the appliance.
Important warnings are identified by these symbols. It is vital to
respect these warnings.
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
•
Before cleaning the outside of the appliance, turn it off,
unplug from the mains socket and allow to cool.
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Danger of burns!
Failure to observe the warning could result in burns or scalding.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they
have been given supervision or instruction
concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Please note:
This symbol identifies important advice or information for the
user.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on pages 2 and 3.
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the sections “Displayed messages” on
page 21 and “Troubleshooting” on page 22.
If this does not resolve the problem or you require further information, you should consult Customer Services by calling the
number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in
the guarantee certificate provided with the machine.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, do not touch the cup warmer shelf, as it is hot.
SAFETY
Fundamental safety warnings
Surfaces marked with this symbol
become hot during use (the symbol
is present on certain models only).
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
Designated use
This appliance is designed and made to prepare coffee and heat
drinks.
7
Description of the control panel
This is a household appliance only.
(page 2 - B )
A number of buttons on the panel have a double function. This is
indicated in brackets in the description.
button: turns the appliance on and off (standby)
B1.
aroma selection button: press to select coffee taste
B2.
B3. CAPPUCCINO button: to make a cappuccino
B4. CAFFELATTE button: to make a coffee with milk (in the
settings menu, press this button to scroll the menu items)
B5. LATTE MACCHIATO button: to make a macchiato
B6. MILK MENU button: to access the functions for preparing
MILK, FLAT WHITE, ESPRESSO MACCHIATO & MY MILK
button: to deliver hot water
B7.
button: to deliver steam (in the settings menu, press
B8.
this button to scroll the menu items)
button: to make 1 cup of LONG coffee
B9.
button: to make 2 cups of coffee with the settings
B10.
displayed
button: to make 1 cup of coffee with the settings
B11.
displayed
B12.OK button: to enable and confirm the selected function
B13.Display: guides the user in using the appliance
B14.MENU/ESC button to access the menu (in the settings
menu: press to exit the menu)
button: to select the quantity of coffee
B15.
It is not intended to be used in:
• staff kitchen areas in shops, offices and
other working environments;
• farm houses;
• by clients in hotels, motels and other residential type environments;
• bed and breakfast type environments.
Any other use is considered improper and thus dangerous.
The manufacturer is not liable for damage deriving from improper use of the appliance.
Instruction for Use
Read these instructions carefully before using the appliance.
Failure to respect these instructions may result in burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Please note:
Keep this Instruction for Use.
If the appliance is passed to other persons, they must also be
provided with this Instruction for Use.
Description of the milk container
DESCRIPTION
Description of the appliance
(page 2 - C )
C1. Froth adjustment and CLEAN dial
C2. Milk container lid
C3. Milk container
C4. Milk intake tube
C5. Frothed milk spout (adjustable)
(page 3 - A )
A1. Beans container lid
A2. Pre-ground coffee funnel lid
A3. Beans container
A4. Pre-ground coffee funnel
A5. Grinding adjustment dial
A6. Cup warmer shelf
A7. Coffee spout (adjustable height)
A8. Hot water and steam connection nozzle
A9. Condensate tray
A10. Coffee grounds container
A11. Cup tray
A12. Drip tray
A13. Drip tray water level indicator
A14. Infuser door
A15.Infuser
A16. Water tank
A17. Water softener filter housing
A18. Water tank lid
A19. Power cable socket
A20. Main switch
Description of the accessories
(page 2 - D )
D1. Pre-ground coffee measure
D2. Cleaning brush
D3. Water softener filter (certain models only)
D4. Button to release the cappuccino maker/hot water spout
D5. Cappuccino maker/hot water spout
D6. Power cable
D7. “Total Hardness Test” indicator strip
D8. Descaler
BEFORE USE
Checking the appliance
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Longhi
Customer Services.
8
Installing the appliance
3. “FILL TANK”: extract the water tank (fig. 4), open the lid
(fig. 5), fill to the MAX line with fresh water (fig. 6); close
the lid again and then replace the tank.
4. INSERT WATER SPOUT”: Check that the hot water spout is
inserted on the connection nozzle and place a container holding a minimum of 100 ml underneath (fig. 7).
5. “Insert Water Spout and Press Ok” is displayed;
6. Press the button to confirm (fig. 3). The appliance delivers water from the spout then goes off automatically.
The coffee machine is now ready for normal use.
Important!
When you install the appliance, you should respect the following safety warnings:
• The appliance gives off heat. After positioning the appliance on the worktop, leave a space of at least 3 cm between
the surfaces of the appliance and the side and rear walls
and at least 15 cm above the coffee machine.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces (e.g.
electric hot plates).
•
•
Setting up the appliance
•
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Please note!
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before it starts
to give satisfactory results.
When making the first 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
To enjoy your coffee even more and improve the performance of your appliance, we recommend installing a water
softener filter as described in the section “ WATER SOFTENER FILTER “ (page 19). If your model is not provided
with a filter, you can request one from De’Longhi Customer
Services.
TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch is
pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this cycle.
Using the appliance for the first time
Please note!
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the Instruction for use in the section “Setting
water hardness (page 19).
1. Plug the power cable into the socket on the back of the
appliance and connect the appliance to the mains power
supply (fig. 1) and make sure that the main switch, located
on the side of the appliance, is pressed (fig. 2).
Select the desired language by scrolling forwards or backwards
using the CAFFELATTE or
button, or alternatively waiting
for the language options to scroll automatically on the display
(about every 3 seconds):
2. When “English” appears, hold the
button (fig. 3) for a
few seconds until “English set” is displayed.
Follow the instructions indicated on the appliance display:
•
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
button (fig. 8).
To turn the appliance on, press the
The message “Heating up, Please wait” is displayed.
After heating, the message “Rinsing” is displayed. As well as heating the boiler, the appliance also heats the internal circuits by
circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coffee appears.
•
TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
9
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Adjust time” is displayed;
3. Press the OK button (fig. 10): the hours flash;
4. Press < or > (fig. 9) to change the hours;
5. Press the OK button to confirm: the minutes flash;
6. Press < or > (fig. 9) to change the minutes;
7. Press the OK button to confirm.
This sets the time. Press the MENU/ESC button to exit the menu.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
button (fig. 8).
• To turn the appliance off, press the
• The message “Turning off, Please wait” is displayed: if featured, the appliance completes a rinse cycle and then goes
off (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• first turn the appliance off by pressing the
button
(fig. 8);
• release the main switch at the back of the appliance (fig.
2).
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly.
Important!
Never press the main switch while the appliance is on.
To enable auto-start, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Auto-start” is displayed;
3. Press the OK button. “Enable?” is displayed;
4. Press the OK button to confirm;
5. Press < or > to choose the hours;
6. Press the OK button to confirm;
7. Press < or > (fig. 9) to change the minutes;
8. Press the OK button to confirm;
9. Then press the MENU/ESC button to exit the menu.
Once the time has been confirmed, activation of auto-start is
indicated by the
symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the OK button. “Disable?” is displayed;
3. Press the OK button to confirm.
The
symbol is no longer displayed.
MENU SETTINGS
When you access the settings menu by pressing the MENU/ESC
button, scroll the menu items by pressing < or > (fig. 9).
Rinsing
Use this function to deliver hot water from the spout to heat the
internal circuit and make the coffee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Rinsing” is displayed;
3. Press the OK button: “Confirm?” will be displayed.
4. Press the OK button (fig. 10): after a few seconds, hot water
flows out of the spout, heating the internal circuit and making the coffee delivered hotter.
Please note!
Press any button to stop hot water delivery at any time.
Auto-Off (standby)
For instructions on how to replace the filter, see the section “Replacing the filter” (page 20).
Auto-off mode can be set, so that the appliance switches off
when not used for 15 or 30 minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Auto-off” is displayed;
3. Press the OK button;
4. Press < or > (fig. 9) until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to confirm;
6. Then press the MENU/ESC button to exit the menu.
Auto-off is programmed.
Adjust time
Cup warmer
Descaling
For instructions on descaling, see page 18.
Install filter
For instructions on how to install the filter, see the section
“Water softener filter” (page 19).
Replacing the filter (if installed)
To adjust the time on the display, proceed as follows:
This function allows the cup warmer to be enabled or disabled.
10
Setting water hardness
Proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Cup warmer” is displayed;
3. Press the OK button: “Enable?” or “Disable?” will be
displayed
4. Press the OK button to enable or disable the cup warmer
(“Cup warmer” “Enabled” on the display indicates the function is enabled)
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coffee hot.
For instructions on setting water hardness, see page 20.
Setting the language
To modify the language of the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Set language” is displayed;
3. Press the OK button;
4. Press < or > until the required language is displayed;
5. Press the OK button to confirm;
6. A message confirming the language installed is displayed;
7. Then press the MENU/ESC button to exit the menu.
Energy saving
Use this function to enable or disable energy saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Energy saving” is displayed;
3. Press the OK button. “Disable?” is displayed (or “Enable?” if
the function has been disabled);
4. Press the OK button to disable (or enable) energy saving
mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is active, if the machine is not used for some
time, “Energy saving” is displayed.
Beep
This enables or disables the beep emitted by the appliance whenever a button is pressed or an accessory is inserted/removed.
To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Beep” is displayed;
3. Press the OK button: “Disable?” is displayed (or “Enable?” if
disabled);
4. Press the OK button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set).
To reset the default values, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Default values” is displayed;
3. Press the OK button;
4. “Confirm?” is displayed;
5. Press the OK button to confirm and exit.
Please note!
• When in energy saving mode, a few seconds elapse before
the first coffee, cappuccino or milk based coffee is delivered
as the appliance must heat up again.
• To prepare any drink, press any button to exit energy saving, then press the button corresponding to the drink you
want to make.
• If the milk container is inserted, “Energy saving” is not
activated.
Statistics function
This displays statistics relating to the machine. To display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Statistics” is displayed;
3. Press the OK button;
4. Press < or > (fig. 9) to verify:
- how many coffees have been made;
- the total number of cappuccinos and milk based coffees
made;
- the total number of litres of water delivered.
- how many times the machine has been descaled.
- how many times the water softener filter has been
replaced.
Setting the temperature
To modify the temperature of the water used to make the coffee,
proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (fig. 9) until “Set temperature” is displayed;
3. Press the OK button;
4. Press < or > until the required temperature (●=low;
●●●●=maximum) is displayed;
5. Press the OK button to confirm;
6. Then press the MENU/ESC button to exit the menu.
11
5. Press the MENU/ESC button twice to exit the menu.
Please note!
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
If the coffee is delivered too slowly or
not at all, turn one click clockwise towards “7”.
For fuller bodied creamier coffee, turn
one click anticlockwise towards “1” (do
not turn more than one click at a time
otherwise the coffee could be delivered
a drop at a time). These adjustments will only be evident after
at least 2 cups of coffee have been delivered. If this adjustment
does not obtain the desired result, turn the dial another click.
MAKING COFFEE
Selecting the coffee taste
The appliance is set by default to make coffee with a standard
taste. You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
button (fig. 11) repeaTo change the taste, press the
tedly until the required taste is displayed.
Selecting the quantity of coffee in the cup
Tips for a hotter coffee
The appliance is set by default to make a standard quantity of
coffee. To select the quantity of coffee, press the
button (fig. 12) until the message corresponding to the required
quantity of coffee is displayed:
Coffee selected
Quantity in cup (ml)
MY COFFEE
Programmable:
from ≃20 to ≃180
SHORT
≃40
STANDARD
≃60
LONG
≃90
EXTRA LONG COFFEE
≃120
For hotter coffee, you should:
• perform a rinse cycle, selecting the “Rinsing” function in
the settings menu (page 10).
• warm the cups by rinsing them with hot water (using the
hot water function);
• increase the coffee temperature in the settings menu
(page 11).
Making coffee using coffee beans
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1.
2.
3.
Fill the container with coffee beans (fig. 15).
Place under the coffee spouts:
- 1 cup, if you want to make 1 coffee (fig. 13);
- 2 cups if you want 2 coffees (fig. 16).
Lower the spout as near as possible to the cups (fig. 16).
This makes a creamier coffee.
4. Press the button corresponding to the number of coffees
required (1 cup
or 2 cups
).
5. Preparation begins. The amount of coffee selected is displayed together with a progress bar which gradually fills
as preparation progresses.
Customising the “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml of
“MY COFFEE”. To modify this quantity, proceed as follows:
1. Place a cup under the coffee spouts (fig. 13).
2. Press the
button (fig. 12) until “MY COFFEE” is
displayed.
3. Keep the
button (fig. 17) pressed until the message
“1 MY COFFEE Program quantity” is displayed and coffee
delivery begins. Release the button.
4. As soon as the coffee in the cup reaches the required level,
button (fig. 17) again.
press the
The quantity of coffee in the cup set has now been programmed.
Please note:
While the machine is making coffee, delivery can be interrupted at any moment by pressing any button.
• At the end of delivery, to increase the quantity of coffee in
the cup, just press (within 3 seconds) one of the coffee buttons (
or
) (fig. 17).
Once the coffee has been made, the appliance is ready to make
the next drink.
•
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (fig. 14).
12
•
•
•
Press OK”. Add one level measure of pre-ground coffee and press
OK.
Coffee delivery resumes and the progress bar gradually fills as
preparation progresses.
Please note!
Various alarm messages could be displayed while using
the machine (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in the section “Displayed
messages” (page 22).
For hotter coffee, see the section “Tips for a hotter coffee”
(page 12).
If the coffee is delivered a drop at a time, too weak and
not creamy enough or too cold, read the tips in the “Troubleshooting” section on (page 22).
Customising the LONG coffee quantity
The appliance is set by default to automatically deliver 200 ml of
“LONG” coffee. To modify this quantity, proceed as follows:
1. Place a sufficiently large cup or a glass under the coffee
spouts (fig. 9).
2. Keep the
button pressed (fig.17) until “Program
quantity” is displayed.
button: coffee delivery begins.;
3. Release the
4. As soon as the coffee in the cup reaches the required level,
press the
button (fig. 17) again.
The quantity of LONG coffee in the cup set has now been
programmed.
Making coffee using pre-ground coffee
•
•
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
Never use more than one level measure or it could dirty the
inside of the machine or block the funnel.
Please note!
If you customise the LONG coffee by using the preground coffee,
a second measure will be requested.
Please note!
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
MAKING CAPPUCCINOS AND MILK BASED COFFEES
1. Press the
button (fig. 11) repeatedly until “Preground” is displayed.
2. Open the lid on the bean container; then open the lid on
the pre-ground coffee funnel and lift it up.
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 18).
4. Place a cup under the coffee spouts.
.
5. Press the 1 cup button
6. Preparation begins. The amount of coffee selected is displayed together with a progress bar which gradually fills
as preparation progresses.
•
Please note!
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water connection nozzle as described in the section “Cleaning the milk
container” on pages 14 and 17.
Filling and attaching the milk container
1. Remove the lid (fig. 19);
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the handle (fig.
20). Each mark on the side of the container corresponds to
around 100 ml of milk.
Please note!
If “Energy saving” mode is active, you may have to wait a few
seconds before the first coffee is delivered.
•
Making LONG coffee using coffee beans
•
Prepare the appalicen following the same procedure indicated
to the paragraph “Making coffee using coffee beans”, then press
the
button.
Please note!
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
If “Energy saving” mode is enabled, you may have to wait a
few seconds before the first coffee is delivered.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 21).
4. Place the lid back on the milk container.
5. Remove the hot water spout (D5), by pressing the button
on the spout (fig. 22A)
Making LONG coffee using pre-ground coffee
Follow steps 1 to 4 of the paragraph “Making coffee using preground coffee”, then press the
button.
The appliance starts coffee delivery and a progress bar is displayed; halfway, the appliance displays “Insert preground coffee”,
13
6. Attach the milk container to the connection nozzle and
push as far as it will go (fig. 23). The machine emits a beep
(if the beep function is enabled).
7. Place a sufficiently large cup under the coffee and frothed
milk spouts. Adjust the length of the milk spout. To move it
nearer the cup, simply pull it downwards (fig. 24).
8. Follow the instructions below for each function.
4. Press < or > until the required drink is displayed (MILK,
FLAT WHITE, ESPRESSO MACCHIATO or MY MILK).
5. Press the OK button to start making the drink.
6. After a few seconds, frothed milk is delivered from the milk
spout into the cup below.
For drinks with coffee, the machine automatically makes
the coffee after delivering the milk.
Adjusting the amount of froth
Turn the froth adjustment dial to adjust the amount of froth on
the milk delivered while making cappuccino and milk based
coffees.
Dial
position
•
Description
Recommended for…
•
No froth
CAFFELATTE / MILK (hot
milk)
•
Min. froth
MACCHIATO / FLAT WHITE
Max. froth
CAPPUCCINO / MILK
(frothed milk) / ESPRESSO
MACCHIATO
Please note: general instructions for all milk based
preparations
If during delivery you want to stop preparation, press any
button once.
At the end of delivery, to increase the quantity of milk or
coffee in the cup, within 3 seconds, press and hold one of
the buttons corresponding to the milk based drinks.
Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
Cleaning the milk container after use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
Making milk based coffees automatically
The control panel features buttons for automatically making
CAPPUCCINO, CAFFELATTE, and MACCHIATO.
To make one of these coffees, proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required coffee: the
name of the coffee is displayed, together with a progress
bar which fills gradually as preparation proceeds.
4. After a few seconds, frothed milk is delivered from the milk
spout into the cup below.
Subsequently, the machine automatically makes the coffee
after having delivered the milk.
“SET DIAL TO CLEAN” flashes on the display each time you use a
milk function. To eliminate all milk residues, proceed as follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk spout.
3. Turn the froth adjustment dial to “CLEAN” (fig. 25). A progress bar appears and gradually fills as the operation proceeds together with “Cleaning underway”. Cleaning stops
automatically.
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
connection nozzle with a sponge (fig. 26).
Making hot drinks using the “MILK MENU”
•
As well as the coffees described above, the machine automatically makes MILK (hot milk), FLAT WHITE, ESPRESSO MACCHIATO
and MY MILK (customisable).
To make one of these hot drinks, proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the MILK MENU button.
•
•
14
Please note!
To prepare a number of cappuccinos or milk based coffees,
clean the milk container after you have prepared the last
drink only.
The milk container can be kept in the refrigerator.
In some cases, to clean you must wait for the appliance to
heat up.
Programming the quantity of coffee and milk
in the cup for the CAPPUCCINO, CAFFELATTE and
MACCHIATO buttons
Please note!
If “Energy saving” mode is active, you may have to wait a few
seconds before the hot water or steam is delivered.
The appliance is set by default to automatically deliver standard
quantities. To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press and hold one of the function buttons until the name
of the hot drink and the message “PROGRAM MILK” is
displayed.
3. Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
5. The appliance stops delivering milk and, if included in the
drink, after a few seconds the coffee is delivered into the
cup: the name of the hot drink and “PROGRAM COFFEE” is
displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the button again. Coffee delivery stops.
The machine is now reprogrammed with the new milk and coffee quantities.
Delivering hot water
1. Make sure the hot water spout is attached correctly (fig. 7).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the
button (fig. 3). “HOT WATER” is displayed,
together with a progress bar which fills gradually as preparation proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically. To interrupt delivery of hot water manually, press the button again.
Changing the quantity of water delivered
automatically
The machine is set by default to automatically deliver 250 ml
of hot water.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press and hold the button until “Hot water Program
button.
quantity” is displayed, then release the
3. When the hot water in the cup reaches the required level,
press the
button again.
The machine is now reprogrammed with the new quantity.
Programming the quantity of coffee and milk in
the cup for the MILK MENU button drinks
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Press the MILK MENU button.
2. Press < or > until the required drink is displayed (MILK,
FLAT WHITE, ESPRESSO MACCHIATO or MY MILK).
3. Hold the OK button until the name of the drink and “PROGRAM MILK” are displayed.
4. Release the button. The appliance starts delivering milk.
5. Once the required quantity of milk has been delivered into
the cup, press the OK button.
6. The appliance stops delivering milk and, if included in the
drink, after a few seconds the coffee is delivered into the
cup: the name of the hot drink and “PROGRAM COFFEE” is
displayed.
7. Once the required quantity of coffee has been delivered
into the cup, press the OK button again. Coffee delivery
stops.
The machine is now reprogrammed with the new milk and coffee quantities.
Delivering steam
1. Make sure the hot water spout is attached correctly (fig. 7).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker (D5) in the liquid.
3. Press the
button: after a few seconds, steam comes
out of the cappuccino maker and heats the liquid; “STEAM”
is displayed.
4. When the required temperature is obtained, interrupt
steam delivery by pressing the button. (You should not
discharge steam for more than 3 minutes at a time).
Important!
Always stop steam delivery before extracting the container containing the liquid to avoid burns from splashes.
Tips for using steam to froth milk
•
DELIVERING HOT WATER AND STEAM
•
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water or steam.
The spout becomes hot. Hold by the handle only.
•
15
When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
For a richer denser froth, use skimmed or partially skimmed milk at refrigerator temperature (about 5°C).
For a creamier froth, rotate the container with slow movements in an upward direction.
•
Cleaning the coffee grounds container
To avoid milk with poor froth or large bubbles, always clean
the spout as described in the following section.
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance will
not make coffee.
Even if not full, the empty grounds container message is displayed 72 hours after the first coffee has been prepared. For the
72 hours to be calculated correctly, the machine must never be
turned off using the main switch.
Cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and press
the button to deliver a little water (fig. 3). Stop the
flow of hot water by pressing the
button again.
2. Wait a few minutes for the cappuccino maker to cool down,
then press the button on the hot water spout and extract
it (fig. 27A). Hold the spout with one hand and with the
other, turn the cappuccino maker anticlockwise (fig. 27B)
and pull downwards to remove.
3. Also remove the steam connection nozzle by pulling it
downwards (fig. 28).
4. Check the hole shown by the arrow in fig. 29 is not blocked.
If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, pushing it upwards and turning it until it is
attached.
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray becomes hot. Wait for it to cool down before touching it and handle it from the front only.
To clean (with the machine on):
• Extract the drip tray (fig. 30), empty and clean.
• Empty the grounds container and clean thoroughly to remove all residues left on the bottom. This can be done with
the spatula on the brush provided.
• Check the condensate tray and empty if necessary (fig. 31).
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine.
CLEANING
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- coffee grounds container (A10),
- drip tray (A12),
- water tank (A16),
- coffee spouts (A7),
- hot water/steam connection nozzle (A8)
- pre-ground coffee funnel (A4),
- the infuser (A15), accessible after opening the service door
(A14),
- control panel (B)
- milk container (C)
•
•
•
Cleaning the drip tray and condensate tray
Important!
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 32).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned, otherwise the water may overflow the edge and damage the appliance, the surface it rests on
or the surrounding area.
To remove the drip tray:
1. Extract the drip tray and grounds container (fig. 30);
2. Empty the drip tray and grounds container and wash them;
3. Check the condensate tray and empty if necessary.
4. Replace the drip tray complete with grounds container.
Important!
Do not use solvents, abrasive detergents or alcohol to clean
the appliance. With De’Longhi superautomatic coffee machines, you need not use chemical products to clean the
machine.
None of the components of the appliance can be washed in
a dishwasher with the exception of the milk container (C).
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Cleaning the inside of the coffee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned off
(see “Turning off”) and unplugged from the mains power supply. Never immerse the coffee machine in water.
16
33
PU
SH
PU
SH
1. Check regularly (about once
a week) that the inside of
the appliance (accessible
after removing the drip
tray) is not dirty. If necessary, remove coffee deposits
with the brush supplied and
a sponge.
2. Remove the residues with a
vacuum cleaner (fig. 33).
35
36
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 36).
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Cleaning the water tank
1. Clean the water tank (A16) regularly (about once a month
and whenever you replace the water softener filter (if present) with a damp cloth and a little mild washing up liquid.
2. Remove the filter (if present) and rinse with running water.
3. Replace the filter (if present), fill the tank with fresh water
and replace the tank.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
6. Use the brush (D2) to remove any coffee residues left in the
infuser housing, visible through the infuser door.
7. After cleaning, replace the infuser by sliding it onto the
internal support (fig. 37), then push the PUSH symbol fully
in until it clicks into place.
Infuser
support
Cleaning the coffee spouts
1. Clean the coffee spouts
regularly with a sponge or
cloth (fig. 34).
2. Check the holes in the coffee spout are not blocked.
If necessary, remove coffee
deposits with a toothpick
(fig. 34).
34
37
Cleaning the pre-ground coffee funnel
Please note!
If the infuser is difficult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in fig. 38.
Check regularly (about once a month ) that the pre-ground coffee funnel (A4) is not blocked.
If necessary, remove coffee deposits with the brush (D2)
supplied.
Cleaning the infuser
Small lever
The infuser (A15) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see “Turning
off”, page “TURNING THE APPLIANCE OFF” a pagina 9).
2. Extract the water tank (fig. 4).
3. Open the infuser door (fig. 35) on the right side of the
appliance.
Large lever
38
8. Once inserted, make sure the two red buttons have snapped out (fig. 39).
17
PU
SH
6. Check that the intake tube and spout are not clogged with
milk residues.
7. Replace the dial (in correspondence to the word “INSERT”),
spout and milk intake tube.
8. Place the lid back on the milk container.
Cleaning the hot water/steam connection nozzle
Each time you prepare milk, clean the connection nozzle with a
sponge to remove milk residues from the gaskets (fig. 26).
39
9. Close the infuser door.
10. Replace the water tank.
DESCALING
Descale the machine when the message “DESCALE” flashes on
the display.
Cleaning the milk container
Clean the milk container every two days as described below:
1. Remove the lid.
2. Remove the milk spout and intake tube.
3. Turn the froth adjustment dial clockwise to the “INSERT”
position (fig. 40) and pull off upwards.
•
•
Important!
Descaler contains acids which may irritate the skin and
eyes. It is vital to respect the manufacturer’s safety warnings given on the descaler pack and the warnings relating
to the procedure to follow in the event of contact with the
skin and eyes.
You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer’s guarantee.
1.
2.
3.
4.
Turn the machine on.
Press the MENU/ESC button to enter the menu.
Press < or > until “Descale” is displayed.
Select by pressing the OK button: Confirm? is displayed.
Press the OK button to confirm.
5. “EMPTY THE DRIP TRAY” is displayed, alternating with “REMOVE FILTER” (if the filter is featured) and “ADD DESCALER,
Press OK”.
6. Empty the water tank (A16) completely and remove the
water softener filter (if present). Empty the drip tray (fig.
30) and grounds container, then put them back in the
appliance.
7. Pour the descaler into the
tank up to level A (correA
B
sponding to a 100 ml
pack) marked on the back
of the tank (fig. 43), then
add water (1 litre) up to
B
level B (fig. 43) and put
the water tank back.
8. Place an empty container
with a minimum capacity
A
43
of 1.5 litres under the hot
water spout (fig. 7).
40
4. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dishwasher
safe, placing them in the top basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (fig. 41). If necessary, scrape the
groove with a toothpick.
41
42
5. Rinse inside the froth adjustment dial seat with running
water (fig. 42)
Important! Danger of burns
Hot water containing acid flows out of the hot water spout.
18
Avoid contact with splashes of water.
9. Press the OK button to confirm that you have added the
solution. The descale programme automatically performs
a series of rinses and pauses to remove limescale deposits
from inside the machine.
“Descale underway” is displayed. The descale programme
starts, and descaler comes out of the water spout.
After about 30 minutes, the message “RINSING, INSERT FILTER”
(if removed previously) is displayed, alternating with “FILL
TANK”.
10. The appliance is now ready for rinsing through with clean
water. Extract the water tank, empty, rinse under running
water, fill with clean water up to the MAX level, insert the
filter (if removed previously) and put the water tank back
in the machine. “RINSING, Press OK “ is displayed.
11. Empty the container used to collect the descaler solution
and replace it empty under the hot water spout.
12. Press the OK button to start rinsing. Hot water flows out
of the spout and the message “RINSING, Please wait” is
displayed.
13. When the water tank is completely empty, the message
“Rinsing complete, Press OK” is displayed.
14. Press the OK button.
15. “Heating up Please wait” is displayed, at the end of which
the machine will be ready for use.
Setting water hardness
Press the MENU/ESC button to enter the menu.
Press < or > to select “Water hardness”.
Press the OK button to confirm the selection.
Press < or > and set the hardness level as measured by the
indicator strip (see the fig. in the previous paragraph).
5. Press the OK button to confirm the setting.
6. Press the MENU/ESC button to exit the menu.
The machine is now reprogrammed with the new water
hardness setting.
1. 2.
3. 4. WATER SOFTENER FILTER
Certain models are fitted with a water softener filter. If this is not
the case with your model, you are recommended to purchase
one from De’Longhi Customer Services.
To use the filter correctly, follow the instructions below.
Installing the filter
SETTING WATER HARDNESS
The DESCALE message is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness value of 4.
The machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
1. Remove the filter from
the packaging.
2. Turn the date indicator
disk (fig. 44) until the
next two months of use
are displayed.
Please note
The filter lasts about two
months if the appliance is used
44 normally. If the coffee machine
is left unused with the filter installed, it will last a maximum of three weeks.
3. To activate the filter, run tap water through the hole in the
filter as shown in the figure until water comes out of the
openings at the side for more than a minute (fig. 45).
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper from
its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
19
1. Extract the tank and exhausted filter;
2. Take the new filter out of its packet and proceed as illustrated in points 2-3-4-5-6-7 in the previous section;
3. Position a container with a minimum capacity of 500 ml
under the hot water spout;
4. Press the MENU/ESC button to enter the menu;
5. Press < or > until “Replace filter” is displayed;
6. Press the OK button;
7. “Confirm?” is displayed;
8. Press the OK button to confirm the selection;
9. “ Water delivery Press OK” is displayed;
10. Press the OK button to confirm the selection. The appliance
begins hot water delivery and the message “Please wait” is
displayed;
11. After delivery, the appliance is automatically ready to make
the next drink.
The new filter is now active and you can use the coffee machine.
0,5 L
45
46
4. Extract the tank from the appliance and fill with water.
5. Insert the filter in the water tank and immerse it completely for about ten minutes, sloping it and pressing it lightly
to enable the air bubbles to escape (fig. 46).
6. Insert the filter in the filter housing (fig. 47A) and press as
far as it will go.
7. Close the tank with the lid (fig. 47B), then put the tank
back in the machine.
47A
Removing the filter
If you want to use the appliance without the filter, you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Extract the tank and exhausted filter;
2. Press the MENU/ESC button to enter the menu;
3. Press < or > (fig. 9) until “Install filter, Enabled” is
displayed;
4. Press the OK button;
5. “Disable?” is displayed;
6. Press the OK button to confirm and the MENU/ESC button
to exit the menu.
47B
When you install the filter, you must notify the appliance of its
presence.
8. Press the MENU/ESC button to enter the menu;
9. Press < or > (fig. 9) until “Install filter” is displayed;
10. Press the OK button;
11. “Install?” is displayed;
12. Press the OK button to confirm the selection. “Water delivery Press OK “ is displayed;
13. Position a container under the hot water spout (min. capacity: 500 ml).
14. Press the OK button to confirm the selection. The appliance
begins hot water delivery and the message “Please wait” is
displayed.
15. After delivery, the appliance is automatically ready to make the
next drink.
The new filter is active. You can now use the appliance.
TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 15 bar
Max. water tank capacity: 2l
260 x 360 x 460 mm
Size LxHxD: Cable length: 1,75 m
Weight: 11 kg
Coffee beans container capacity: 400 g
The appliance complies with the following EC
directives:
Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see date
indicator) or when the appliance has not been used for 3 weeks,
you should replace the filter:
20
•
Low Voltage Directive 2006/95/EC and subsequent amendments;
•
EMC Directive 2004/108/EC and subsequent amendments;
•
European Stand-by Regulation 1275/2008;
•
Materials and accessories coming into contact with food conform
to EC regulation 1935/2004.
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
FILL TANK
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it
clicks into place.
EMPTY GROUNDS CONTAINER The grounds container (A10) is full.
GROUND TOO FINE ADJUST
MILL
Empty the grounds container and drip tray,
clean and replace (fig. 30). Important: when
removing the drip tray, the grounds container
MUST be emptied, even if it contains few grounds. If this is not done, when you make the next
coffees, the grounds container may fill up more
than expected and clog the machine. If the problem persists, make sure the water tank is fully
inserted, press the
button and deliver a
little water from the spout.
The grinding is too fine and the coffee is delive- Repeat coffee delivery and turn the grinding
red too slowly or not at all.
adjustment dial (fig. 14) one click clockwise towards “7” while the coffee mill is in operation.
If after making at least 2 coffees delivery is
still too slow, repeat the correction procedure,
turning the grinding adjustment dial another
click until delivery is correct (see the section:
“Adjusting the coffee mill on page 12).
INSERT GROUNDS CONTAINER After cleaning, the grounds container has not Remove the drip tray and insert the grounds
been replaced.
container.
ADD PRE-GROUND COFFEE
With the pre-ground function selected, pre- Place pre-ground coffee in the funnel or deseground coffee has not been poured into the lect the “pre-ground” function (fig. 18).
funnel.
DESCALE
The machine must be descaled.
The descaling procedure described in the section
“Descaling” needs to be performed as soon as
possible (page 18).
LESS COFFEE
Too much coffee has been used.
Select a milder taste by pressing the
button (fig. 11) or reduce the quantity of preground coffee.
FILL BEANS CONTAINER
The coffee beans have run out.
Fill the beans container (fig. 15).
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a brush as
described in the section “Cleaning the preground coffee funnel” (page 18).
INSERT INFUSER ASSEMBLY
The infuser has not been replaced after Insert the infuser as described in the paracleaning.
graph “Cleaning the infuser” (page 17).
INSERT TANK
The tank is not correctly in place.
21
The tank is not correctly in place.
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly,
as described in the section “Cleaning”.
If the message is still displayed after cleaning,
contact a service centre.
EMPTY CIRCUIT, FILL CIRCUIT
Water delivery
PRESS OK
The water circuit is empty
Press OK and deliver water from the spout
(D5), until it flows out normally.
REPLACE FILTER
The water softener filter is exhausted.
Replace the filter or remove it as described in
the section “Water softener filter”.
SET DIAL TO CLEAN
Milk has been delivered recently and the tubes
inside the milk container must be cleaned.
Turn the froth adjustment dial to CLEAN.
INSERT WATER SPOUT
The hot water spout is not inserted or is
inserted incorrectly.
Insert the water spout (D5) as far as it will go.
INSERT MILK CONTAINER
The milk container is not inserted correctly.
Insert the milk container (fig. 23) as far as it
will go.
TROUBLESHOOTING
Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee is not hot
The cups were not preheated.
•
•
Enable the cup warmer and let the cups
heat up for at least 20 min.
Warm the cups by rinsing them with hot
water (Please note: you can use the hot
water function).
The infuser has cooled down because Before making coffee, use the special function
2/3 minutes have elapsed since the last to rinse and heat the infuser (page 10).
coffee was made.
A low coffee temperature is set.
The coffee is weak or not creamy The coffee is ground too coarsely.
enough.
The coffee is unsuitable.
The coffee is delivered too slowly or a The coffee is ground too finely.
drop at a time.
22
Set a higher coffee temperature in the menu
(page11).
Turn the grinding adjustment dial one click
anticlockwise towards “1” while the coffee mill
is in operation (fig. 14). Continue one click at
a time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see the section: “Adjusting the coffee mill” on
page 12).
Use pre-ground coffee for espresso machines.
Turn the grinding adjustment dial one click
clockwise towards “7” while the coffee mill is in
operation (fig. 14). Continue one click at a time
until coffee delivery is satisfactory. L’effetto è
visibile solo dopo l’erogazione di 2 caffè (vedi
paragrafo “regolazione del macinacaffè”, page
12).
Coffee does not come out of one of the The spouts are blocked.
spouts.
The appliance does not come on.
Clean the spouts with a toothpick (fig. 34).
The power cable is not plugged in Plug the cable fully into the socket on the back
properly.
of the appliance (fig. 1).
It is not plugged into the mains socket. Plug into the mains socket.
The main switch (A20) is not turned on. Press the main switch (fig. 2).
The infuser cannot be extracted.
The appliance has not been turned off Turn the appliance off by pressing the
correctly.
ton (page 9).
but-
The milk does not The milk container lid is dirty.
come out of the milk
spout.
Clean the milk container lid as described in the
section “Cleaning the milk container” (page
17).
The milk contains The milk is not cold enough or is not
large bubbles and semi-skimmed.
squirts out of the
milk spout or there is
little froth.
The froth adjustment dial is incorrectly
adjusted.
Use skimmed or semi-skimmed milk at refrigerator temperature (about 5° C).
If the result is not as you wished, try changing
brand of milk.
Adjust following the instructions in the section
“Making cappuccinos and milk based coffees”
(page 13).
The milk container lid or froth Clean the milk container lid and dial as descriadjustment dial are dirty.
bed in the section “Cleaning the milk container” (page 17).
The hot water/steam connection noz- Clean the connection nozzle as described in the
zle is dirty
section “Cleaning the hot water/steam nozzle”
(page 18).
The milk contains The spout is dirty.
large bubbles or
squirts out of the
milk spout, or is not
well frothed.
Clean as described in the section “Cleaning the
cappuccino maker after use” (page 15).
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.
23
ELECTRICAL CONNECTION (UK ONLY)
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might find it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in
use.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWNLIVE
13 amp Fuse
Blue to
neutral
Brown to live
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should
only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
24
McGrp.Ru
Сайт техники и электроники
Наш сайт McGrp.Ru при этом не является просто хранилищем
инструкций по эксплуатации, это живое сообщество людей. Они общаются
на форуме, задают вопросы о способах и особенностях использования техники.
На все вопросы очень быстро находятся ответы от таких же посетителей сайта,
экспертов или администраторов. Вопрос можно задать как на форуме, так и
в специальной форме на странице, где описывается интересующая вас техника.