7” Portable Multimedia Player

Thanks for shopping with Improvements!
7” Portable Multimedia Player
Item #452779
To order, call
1-800-642-2112
West Chester, OH 45069
Made in China
0917
If you have questions regarding this product, call
1-800-642-2112 Mon.-Fri. 9:00-5:00 EST
and ask for our product specialists, or e-mail:
productspecialist@improvementscatalog.com
See many more products on the Internet!
www.ImprovementsCatalog.com
CAUTION
SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS ARE INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
1. Read instructions – All the safety and operating instructions
should be read before the appliance is operated.
2. Retain instructions - The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings and cautions on the appliance and
in the operating instructions should be adhered to.
4. Follow instructions - All operating and use instructions should be
followed.
5. Water and Moisture - The appliance should not be used near
water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
in a wet basement, or near a swimming pool or the like.
6. Wall or Ceiling Mounting - The appliance should not be
mounted to a wall or ceiling.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
7. Ventilation - The appliance should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the appliance should not be situated
on a bed, sofa, rug or similar surface that may block the
ventilation openings, or placed in a built-in installation, such
as a bookcase or cabinet, that may impede the flow of air
through the ventilation openings.
8. Heat - The appliance should be situated away from neat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
9. Power Sources - The product should be operated only with
the type of power supply indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operation instructions.
10. Grounding Polarization - This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way this is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician
to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
11. Power-Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
12. Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
13. Nonuse periods - The power cord of the appliance should be
unplugged from the outlet when left when left unused for a
long period of time.
14. Object and Liquid Entry - Care should be taken so that _objects
do not fall and liquids are not spilled into the product
case through product openings.
15. Damage Requiring Service - Unplug this product from the wall
outlet and take it to qualified service personnel under the
following conditions.
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled into, or objects have fallen into the
product.
c) If the product has been exposed to rain or water.
d) If the product does not operate when used according to the
operating instructions, adjust only those controls that are covered by
the operating instructions. Improper adjustment of other controls may
interfere with the product's normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance- this
indicates a need for service.
16. Servicing - The user should not attempt to service the product
beyond that described in the operating instruction. All servicing
should be referred to qualified service personnel.
WARNING: TO AVOID THE RISK OF ELECTRICAL
SHOCK, ALWAYS MAKE SURE THE PRODUCT IS
UNPLUGGED FROM THE ELECTRICAL OUTLET
BEFORE RELOCATING, SERVICING, OR
CLEANING IT.
 Read and follow all instructions. Keep these
instructions for future reference. Heed all warnings.
 Do not use this product near water.
 Do not ceiling- or wall-mount the product.
 Do not block any ventilation openings. Install the
product in accordance with the operating instructions.
 Do not install the product near heat sources, such as
radiators or other apparatus (including amplifiers) that
produce heat.
 Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptacles, and the point where they exit the product.
 Do not use attachments not recommended or sold by
the product manufacturer, as a risk of fire, electrical
shock, or serious personal injury may result.
 Unplug the product during lightning storms or when
unused for long periods of time.
 Do not expose the product to dripping or splashing
water.
 Do not place objects filled with liquid (i.e., vases) on
the product.
 Do not place in or expose the product to direct
sunlight, extreme heat, humid or dusty locations.
 Never operate this product if it has a damaged Power
Cord or plug, is not working properly, has been
dropped, damaged, or exposed to moisture, water or
other liquids.
 Do not attempt to examine or repair this product
yourself. Return the product to a service center for
examination and repair.
THESE IMPORTANT SAFETY
INSTRUCTIONS ARE INCLUDED, AS
APPLICABLE TO THE APPLIANCE,
CONVEYING TO THE USER THE
INFORMATION ITEMIZED BELOW
2
17. Power Lines - An outside antenna system should not be located
18.
19.
20.
21.
22.
in the vicinity of overhead power lines, or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching power lines or circuits as
contact with them might be fatal.
Outdoor Antenna Grounding – If an outside antenna is
connected to the receiver, be sure the antenna system is
grounded so as to provide some protection a g a i n s t voltage surges
and built up static. Section 810 of the National Electrical Code
ANSI/NEFA 70 provides 11forma.tion wJ.th respect to proper
grounding of the mast and supporting structure, grounding
conductress, location of antenna-discharge unit, size of
grounding electrodes, and requirements for the grounding
electrode (see figure).
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
Lightning - For added protection for this product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product
due to lightning and power-line surges.
Safety ·check - Upon completion of any service or repairs to tl1is
product, ask the service technician to perform safety checks to
determine that the product is in proper operation condition.
Over-loading - Do not overload wall outlets, extension cords,
or integral convenience receptacles as this can result in a risk of
fir or electric shock.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GRAPHIC SYMBOLS WITH
SUPPLEMENTARY MARKINGS ARE
LOCATED ON THE BOTTOM OF THE UNIT.
USE OF CONTROLS, ADJUSTMENTS, OR
PERFORMANCE PROCEDURE HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
WARNING:
This product contains lead, a chemical known
to the State of California to cause cancer and
birth defects or other reproductive harm.
Wash your hands after handling.
CAUTION:
This product is equipped with a polarized plug
(one blade is wider than the other blade) as a
safety feature to reduce the risk of electrical
shock. This plug will fit into a polarized outlet
only one way. This is a safety feature. If you
are unable to insert the plug into the electrical
outlet, try reversing the plug. If the plug still
does not fit, contact a qualified electrician.
Never use the plug with an extension cord
unless the plug can be fully inserted into the
extension cord. Do not alter the plug. Do not
attempt to defeat the safety purpose of the
polarized plug.
IMPORTANT INFORMATION REQUIRED BY THE FCC
GROUND
CLAMP
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference; and (2) this
device must accept any interference received, including
interference that may cause undesirable operation.
GROUNDING CONDUCTOR
(NEC SECTION B10-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250 PARTH)
NEC NATIONAL ELECTRICAL CODE
Do not apply oil or petroleum products to this
product.
CAUTION
Invisible laser radiation will be emitted when
the product is open and locks are
defeated. Do not defeat the safety locks.
3
NOTE: This equipment has been tested ai1d found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio elevation reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Illustration of the Controls/Jacks On the Main Unit
23 24 25
1
23 4
9
11 13
8 10 12
14
5
16
15
28
26
27 29
6 7
17
1. SPEAKERS
2. AUX-IN JACK
3. MIC JACK
4. MIC LEVEL CONTROL
5. USB PORT
6. SD/MMC CARD SLOT
7. TFT DISPLAY
8. FUNCTION CONTROL
9. HANDLE
10. VOLUME CONTROL
11. BASS BOOST ON/OFF BUTTON
12. MODE/TV MENU BUTTON
13. PREV/LEFT BUTTON
14. NEXT/RIGHT BUTTON
15. DVD DOOR
16. DVD DOOR OPEN AREA
17. FAST REWIND/DOWN BUTTON
18. STOP/USB/CARD BUTTON
19. PLAY/PAUSE/ENTER BUTTON
20. FAST FORWARD/UP BUTTON
21. TUNING CONTROL
22. BAND CONTROL
23. POWER INDICATOR
24. REMOTE SENSOR
25. FM STEREO INDICATOR
26. TELESCOPIC FM ANTENNA
27. VIDEO JACK
28. AUDIO RIGHT JACK
29. AUDIO LEFT JACK
30. DISPLAY ON/OFF SWITCH
31. BATTERY COMPARTMENT
32. EXTERNAL TV ANTENNA JACK
33. AC SOCKET
34. PHONES JACK
35. POWER ON/OFF SWITCH (OPTIONAL)
36. DC IN JACK (OPTIONAL)
37. VOLTAGE SELECTOR (OPTIONAL)
1
19
18
21
20
22
30
36
* Rating label is located at the bottom of the unit.
31 32 35 37 33
34
Illustration of the Keys on the Remote Controller and Their Main Functions
1. SCREEN OFF/ON button
2. MUTE button
3. P MODE button
4. GUIDE button
5. TV MENU button
6. REPEAT button
7. PLAY button
8. SUBTITLE button
9. AUDIO button
10. PAUSE/STEP button
11. ANGLE/PROGRAM button
12. ZOOM/SLOW button
13. TV/DVD button
14. MTS button
15. DISPLAY button
16. SETUP button
17. P/N button
18. NUMERIC buttons
19. DVD MENU button
20. STOP&DVD/USB/SD button
21. OK button
22. NAVIGATION buttons
23. TITLE button
24. NEXT/F.FWD button
25. PREV/ F.BWD button
26. SEARCH button
27. CC (Closed Captioning) button
15
16
1
17
2
3
18
4
5
19
6
7
8
20
21
9
23
10
11
12
13
14
24
25
26
27
22
4
RADIO OPERATION
TV OPERATIONS
TO PLAY THE RADIO
GET STARTED
1. Rotate the FUNCTION CONTROL to the RADIO position, the
POWER Indicator will light up.
2. Select the desired band with the BAND switch.
3. Tune to the desired station by rotating the TUNING control
(Move the control back and forth until you get the strongest
clearest sound).
4. The built-in AM antenna and external FM TELESCOPIC
ANTENNA are directional.
 When receiving an FM broadcast, fully extend the
TELESCOPIC ANTENNA and position for the best
reception.
For AM broadcasts, rotate the whole set until the best
reception is heard.
5. Adjust the volume level to a comfortable listening level.
6. To turn off the radio, rotate the FUNCTION CONTROL to OFF
position.
NOTES:
If a particular FM (STEREO) station is weak, or you hear
too much background noise, try moving the position of
the band selector switch to the FM (MONO) position.
This can often result in a much clearer reception.
When the band selector switch is set to FM STEREO
and a stereo broadcast is being received, the FM
STEREO indicator the unit will be light.

Be sure the included TV antenna is connected to the set
properly.
 Power on the unit. Rotate FUNCTION CONTROL to
TV/DVD position, and press TV/DVD button on the remote
or press and hold the MODE/TVMENU button on the unit to
switch to TV mode.
1. Press TV MENU to enter the TV setup menu. Then
scroll right to the Satellite Dish icon. Press OK on the
remote control.
2. Then you will see ANTENNA. Be sure to choose AIR.
Then scroll down to AUTO SCAN and press OK on
the remote control
• To view off air Free Digital TV channels: Change
ANTENNA to read CATV, then follow the above.
• To view CABLE TV channels, Choose CATV option.
Select the proper Cable system and enter the Start to
Scan option to begin auto scan for scanning channels.
(Frequency range: 57 - 855 MHz)
BASIC OPERATIONS
SEARCH A PROGRAM
 Press FAST REWIND button or FAST FORWARD button on
the unit or navigation up/down button on the remote once,
the channel number changes. A desired channel can be
 reached using these two keys.
NUMERIC button on the remote ca n facilitate you to select
a specific channel. If the channel number exceeds 10, input
 first digital unit, then another digital unit;
Note: this receiver can store the channels from 2~69, and
the maximum of each channel has 8 programs. To select the
 desired programs by using - button and numeric buttons.
Do as follows:
To select CH 13 NO. 2
Press 1 and 3, then press +10 and input 2.
Once the input is done, it will start broadcasting the selected
channel immediately.
STEREO HEADPHONE JACK
A stereo headphone jack has been provided on the top of the unit
so that you can listen to the unit without disturbing others. To use
this jack, plug in the headphones/earphones (not included) and
adjust the VOLUME control to a comfortable listening level.
NOTE: When external headphones/earphones are connected,
the sound to the unit's main speakers will be muted.
AUXILIARY IN
Your player can be used as a power amplifier to playback the
programs from portable radio, TV set or Mp3 player or
whatever provide this appliance is so designed that audio
signal may be produced through a LINE-OUT jack or the like.
Observe the following steps to connect the player to another
appliance:
1. Power the player on using the supplied AC Power Cord.
2. Rotate the FUNCTION CONTROL to AUX-IN position.
3. Connect the appliance into the player's AUX-IN jack with
supplied LINE-OUT cable of the appliance.
4. Power on the appliance and begin play.
At this time you will be able to hear the sound produced from
the programs the connected appliance is broadcasting.
ADJUST AUDIO OUTPUT LANGUAGE
During TV playback, press MTS button to adjust the audio
output language.
DISPLAY PROGRAM INFORMATION
Press DISPLAY button to display current program information
including current channel mode, resolution, current calendar
and time, soundtrack mode.
SET CLOSED CAPTION
The CC button is used to set the closed caption mode. Press
CC button repeatedly to set the CC mode (Off/On/CC on mute).
MIC
The MIC jack works in disc, USB and card mode. If you want to
use the microphone for singing or speaking, please connect it
to MIC jack.
MUTE
In TV mode, press MUTE button to shut off the audio output,
press it again resume normal play.
SOUND MODE
During TV broadcasting, press AUDIO button repeatedly to
switch sound mode among personal, standard, movie and
music.
PICTURE MODE
In TV play mode, press P MODE button on the remote several
times to select your desired picture mode (Personal, Standard,
Dynamic, Soft)
ELECTRONIC PROGRAM GUIDE
Use GUIDE button to check information of the program guide
for the past and future. The Information in the EPG depends on
your signal provider.
5
12V DC JACK (OPTIONAL)
DC 12V JACK (Center is positive) in 2mm (inner diameter) type
for connection to an external power source of an AC adaptor or
a car adaptor.
Please make sure that the DC voltage is 12V and with correct
polarity as per below.
Basic connection


It is recommended to be connected to a multi-system TV.
Ensure that this player and other equipment to be connected
to the unit are in the standby or off mode and disconnect the
AC power cords before commencing connection.
Do not block ventilation holes of any piece of the equipment
and arrange them so that air can circulate freely.
Read through the instructions before connecting other
equipment.
Ensure that you observe the color coding when connecting
audio, video cables.
Center pin is positive
OPERATIONS
Note:
 During DVD play, the TV volume may be at a lower level
than during TV broadcasts, etc. If this is the case, adjust the
volume to the desired level.
If the DVD/CD player is connected to the TV through a video
cassette recorder, the picture may not be played back
normally with some DVDs. If this is the case, do not connect
the player via the VCR.
PREPARATION
Before powering on the TV, be sure to set the rear display switch
to on.
Power on the TV set and select video input mode.
Power on the audio system which is connected to the player.
TO PLAY A DVD
1. Rotate the FUNCTION CONTROL to TV/DVD position.
2. Lift CD cover to open the disc tray.
3. Place a disc onto the disc tray.
4. Close the disc tray and press the Play button ( No. 7 on the
Remote Control or No. 9 on the Main Unit.)
5. When a menu screen appears on the TV, move the navigation
buttons or press the numeric buttons to select a preferred track
number, then press OK button to start playback.
6. Turn the function switch to OFF position to turn off the unit.
Note: Sometimes it is necessary to use TV/DVD button on the
remote or MODE/TV MENU on the unit to switch to DVD mode.
The procedures as following: Press TV/DVD button on the
remote or press and hold MODE/TV MENU button on the unit
until a prompt shows on the screen, then use navigation button
to highlight DVD and press OK Button to enter DVD mode.
Connecting to a stereo TV set
To power outlet
AC power cord
RL
To video input connector (yellow)
To audio input connectors (red, white)
Video/audio cable
ADJUST THE VOLUME
Turn VOLUME CONTROL to increase or reduce the volume.
SKIP AHEAD OR BACK
Press NEXT or PREV button once during play to skip a chapter
(DVD) or a track (CD) ahead or backwards.
RAPID ADVANCE/REVERSE
During playback, press and hold FAST FORWARD button or
FAST REWIND button several times to scan the disc forward or
backward at X2, X4, X8, X20 normal speed.
Press PLAY button to resume normal play.
Connecting the Digital TV Antenna to the
player
MUTE
During playback, press MUTE button to shut off the audio
output, press it again resume normal play.
STOP PLAYBACK
Press STOP button during playback to stop playback; the player
activates its resume function when STOP is pressed in STOP
mode; press PLAY button again, playback resumes at the point
it stopped previously; open the disc tray or press the STOP
button one more time to clear the resume function.
ANTENNA INPUT
SLOW-MOTION PLAY (DVD)
Press SLOW button on the remote control during playback, the
disc will be played at 1/ 2 normal speed at first, each time this
button is pressed, the play speed becomes slower (down to 1/7
normal speed.)
Press PLAY button, normal play will resume.
CABLE
Optional
REPEAT BUTTON
Press REPEAT button during play, it will repeat play one
chapter/title or repeat all (for DVD disc), or repeat play a track
or all tracks (CD), or repeat the specified points (A-B).
SWITCH TV SYSTEM
During playback, press P/N button to switch TV system directly.
6
PAUSE/STEP PLAY
Press PAUSE/STEP button during playback to pause. during
pause mode, each time the PAUSE/STEP button is pressed,
the player will only play one frame; to resume normal play,
press PLAY button.
CHANGING SUBTITLE LANGUAGE (DVD ONLY)
Press SUBTITLE button during playback, the subtitle language
shown on the screen will change as a response to each press;
When the desired language appears, release the button to view
the subtitle in that language.
Note: this function only works on the DVDs recorded with multilanguage subtitles.
DISPLAY ON/OFF
During playback, press SCREEN ON/OFF button on the
remote or slide DISPLAY ON/OFF switch on the unit to turn
on/off the display.
RETURN TO MAIN MENU AND PLAY THE TITLE (DVD)
During playback, press DVD MENU button to return to main
menu. Press TITLE button to play the title.
BASS BOOST
During playback, press BASS BOOST button on the unit to
enable or disable the bass effect.
MP3/MPEG 4 PLAYBACK
1. Load the MP3/MPEG 4 disc onto the disc tray and the TV
screen will show all its folders after a few seconds.
2. Select the folder you want by the navigation buttons and
then ENTER button to confirm.
3. The files in this folder are displayed and select your
favorable song via navigation buttons and press ENTER
button to start playback.
4. Press NEXT and PREV button to select track directly.
5. Press REPEAT button change play mode.
SEARCH FOR PREFERRED SCENE
1. Press SEARCH button during play and highlight the item to
be played (Title, Chapter, or Chapter time) by navigation
buttons
2. Input the desired number or time via the numeric buttons.
3. Press OK button to confirm and the playback from the
located scene starts.
4. To exit search menu, press SEARCH button directly.
KODAK PICTURE CD / JPEG CD PLAYBACK
Slide show of Kodak Picture CD after being loaded begins
automatically;
Folders of JPEG picture CD after being loaded are displayed on
the TV screen; use the navigation buttons to select the desired
folder and then press ENTER button to confirm.
The files in this folder are displayed and you can select your
favorable pictures using the up/down navigation buttons and
press ENTER button to start playback.
Preview of the picture will be displayed while you scroll across
the filenames.
PROGRAM PLAY (UP TO 16 MEMORIES)
1. Press PROGRAM during playback to display the program
menu.
2. Select location(s) to be memorized via navigation buttons
and then enter desired Titles/Chapters numbers via numeric
buttons.
Note: Inputting leading zero is not necessary. Some figure
inputs may be useless, because it's greater figure than total
title/chapter /track number on the disc.
Example: Track 3, press "3"
Track 12, press "+10" and then "2"
Track 21, press "+10" twice and then "1"
3. To start programmed playback, select PLAY on the menu;
pressing PROGRAM button again to exit programming.
4. To clear all items, select the <CLEAR> on the menu, and
then press ENTER button on remote control.
5. You could cancel program mode by clearing all the items in
the program menu.
KODAK PICTURE CD / JPEG CD OPERATIONS
1. PLAY MODES
Press REPEAT button during play to change the play modes.
During playback, press STOP to enter preview mode.
2. SKIP TO NEXT/PREVIOUS PICTURE
Press NEXT button to skip to the next picture or PREV button to
the previous picture.
ZOOM PLAY
Press ZOOM button continuously to zoom in the picture by 2, 3,
and 4 times, zoom out by 1/2, 1/3, 1/4 normal size.
Press this key once more when the picture is at 1/4 size to
return to the normal size display.
Scroll to view the enlarged picture using Navigation buttons.
3. PICTURE ROTATIONS
Press RIGHT and LEFT navigation buttons to rotate the picture
Clockwise and anti-clockwise respectively.
4. PICTURE FLIP AND TURN
Press UP navigation button to flip the picture up or down.
Press DOWN navigation button to turn the picture left or right.
ON SCREEN DISPLAY INFORMATION
When the player is in operation, press DISPLAY button
continuously on the remote control, the screen will
display parts of information (current disc type, title number,
chapter number, playtime, audio language, audio type, subtitle
language and multi angle, etc) in a sequence.
5. PICTURE ZOOM IN/OUT
Press ZOOM button continuously, the picture zooms in by 2, 3,
4 times or zooms out by 1/2, 1/3, 1/4 the original size.
Press this button once more when the picture getting 1/4 size to
return to the normal play.
If the picture is enlarged, you may use the navigation buttons to
view blocked parts of the picture.
CHANGING AUDIO SOUNDTRACK LANGUAGE (DVD DISC)
It is possible to change the audio soundtrack language to a
different language from the one selected at the initial settings
(This operation works only with discs on which multiple audio
soundtrack languages are recorded).
Press AUDIO button during DVD disc play, the sound track
language changes with the current sound track number shown
on the TV screen.
NOTE: When no soundtrack languages are recorded, pressing
this button will not work.
6. SLIDE SHOW TRANSITION MODES
During slide show playback, press the PROGRAM button
cyclically to switch the play mode.
MULTI-ANGLE VIEWING (DVD ONLY)
Press and hold ANGLE button during playback to cycle the
angle available on the disc.
Note: only the DVDs shot with multi-angle scenes have this
function.
7
EXTERNAL MEMORY MEDIA OPERATION (USB & SD/MMC
CARD)
Insert a USB data traveler into the USB port and slide the
FUNCTION SWITCH to the TV/DVD position;
Press and hold STOP button to select USB mode among disc,
USB and card via navigation buttons and press OK to confirm.
An icon of READ USB shows in the LCD and after the USB is
successfully detected and read, the screen will show folders
and tracks on the USB.
It will begin playback from track Number 1 automatically.
NOTE: The player can successfully play the music files with
USB 1.0 and USB 2.0 storage device.
OR
Insert an SD/MMC card into the card slot;
Press and hold STOP button to select CARD mode among
disc, USB and card via navigation buttons and press OK To
confirm. Then the player will enter into SD/MMC mode.
2.3 SUBTITLE LANG- Select preferred subtitle language.
(DVD only, need disc software support)
2.4 MENU LANG - Select preferred disc menu language.
(DVD only, need disc software support)
3. VIDEO SETUP
VIDEO SETUP
BRIGHTNESS
CONTRAST
HUE
SATURATION
EXIT SETUP
3.1 BRIGHTNESS - to set the brightness for the display.
Options: 0/2/4/6/8/10/12
3.2 CONTRAST - to set the contrast effect for display.
Options: 0/2/4/6/8/10/12
3.3 HUE - to set the color impression for display.
Options: -6/-4/-2/0/+2/+4/+6
3.4 SATURATION - to set the saturation level for display.
Options: 0/2/4/6/8/10/12
INITIAL SETTINGS
Initial settings page is for you to make your preferred settings
up for your player. Once the initial settings are done they are
retained in the CPU of the player until otherwise modified.
COMMON PROCEDURES FOR INITIAL SETTINGS
1. Press SETUP button.
2. Use the navigation buttons to select the item you want to
modify, press OK button to confirm, setting page with further
setting items displayed shows on the TV screen. Again use
navigation buttons to make changes. Press again OK
button to confirm modifications.
3. Use navigation buttons to switch to another setting on the
main setting page.
4. Press SETUP button to exit main setting page.
4. SPEAKER SETUP
SPEAKER SETUP
DOWNMIX
EXIT SETUP
1. SYSTEM SETUP
4.1 DOWNMIX
Options: LT/RT- Left/Right mix mode
STEREO- Select this option if you don't have a 5.1
channels amplifier.
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
TV TYPE
DEFAULT
EXIT SETUP
1.1 TV SYSTEM - it is used to select the TV mode.
Please select this option as per your TV set.
1.2 SCREEN SAVER- when the player is not used for several
minutes, a running DVD logo will move across the screen
to protect the screen.
Options: ON: the screen saver is enable.
OFF the screen saver is disable.
1.3 TV TYPE- it is used to select the TV scan mode, please
set as per your TV set.
Options: 4:3PS : Normal Pan & scan mode
4:3LB : normal Letter box mode
16:9 : 16:9 wide screen mode
1.4 DEFAULT - Reset to factory settings.
Options: RESTORE
2. LANGUAGE SETUP
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
MENU LANG
EXIT SETUP
2.1 OSD LANGUAGE - It is used to select different On Screen
Display language for different user.
2.2 AUDIO LANG - select preferred audio language.
(DVD only, need disc software support)
8
TV SETTING MENU
Press once TV MENU button the screen will pop up a setting
menu;
Use the NAVIGATION LEFT/RIGHT buttons to select among
the main setting options, then press NAVIGATION UP/DOWN
button to enter the sub menu, again use NAVIGATION
LEFT/RIGHT button to select the desired option or adjust and
Antenna
Auto Scan
Show/Hide
Channel No.
Channel Label
UP/DOWN
62
53
50
0
60
UP/DOWN
MENU:EXIT
0
MENU:EXIT
Balance: it is used to adjust the balance effect according to your
own favorite.
Audio language: it is used to select the desired audio output
language.
OSD Duration
Sleep Timer
Time Zone
Daylight Saving Time
Clock
UP/DOWN
ADJUST
60 Sec
Off
Central
Off
----/--/-- --/-MENU:EXIT
OSD Duration: it is used to set the OSD display duration.
Sleep Timer: it is used to set the sleep timer to auto power off
the set.
Time Zone: it is used to select time zone from different region.
Daylight Saving time: it is used to advance one hour of the
daylight time in summer in order to save the power.
Clock: it is used to show code create date.
Menu Language
Color Mode
Zoom Mode
Closed Caption
Restore Default
UP/DOWN
English
Normal
Wide
ADJUST
ADJUST
MENU:EXIT
IMPORTANT: Make sure that you plug the external AC
power cord correctly into the rear power Port.
English
ADJUST
Air
Antenna: it is used to select the Antenna type CATV or air.
Auto Scan: use this function to auto scanning and stored
tuned channels. Select auto scan option, then press
NAVIGATION
RIGHT button to access the submenu, select the desired Cable
system and then enter the Start to Scan option to begin auto
scan.
Show/Hide: it is used to show or hide the programs according to
your own favorite.
Channel No.: Select the desired program from this option.
Channel Label: it is used to edit the name of the selected
program (Use up or down button to input symbol or letter as
desired, and press left or right button to enter the previous or
next item).
Picture mode: it is used to select the desired picture mode.
Contrast: it is used to adjust the contrast effect according to
your own favorite.
Brightness: it is used to adjust the brightness effect according
to your own favorite.
Sharpness: it is used to adjust the sharpness according to your
own favorite.
Tint: it is used to adjust the tint effect according to your own
favorite.
Color: it is used to adjust the color according to your own
favorite.
Balance
Audio Language
Basic Selection: select among from CC1, CC2, CC3,
CC4, Text1, Text2, Text3 and Text4.
Advance Selection: service 1, Service 2, Service 3,
Service 4, Service 5, Service 6.
Restore Default: select this option to restore the factory setting.
Personal
ADJUST
CC mode: use to select on, CC on Mute, off.
2.
3.
press OK/ENTER Button to confirm the item to be set;
Press TV MENU to go to previously menu or scroll to top the
main setting options. Use TV MENU button to exit the setup
menu.
Picture Mode
Contrast
Brightness
Sharpness
Tint
Color
UP/DOWN
1.
MENU:EXIT
Menu Language: it is used to change menu language.
Color mode: it is used to change the color mode of screen.
Zoom Mode: it is used to select the display type.
Closed Caption: it is used to select the broadcasting program
provides closed caption. There are three options as follows:
9
DIGITAL TV FACTS
1. Digital TV differs greatly from older Analog TV. When all is right, Digital TV provides a clear, ghost free, highlysaturated, color picture.
2. However, it’s possible that even when a strong signal is available, you may not always receive a picture at all.
Tube-style analog TV will nearly always display a picture, but sometimes it will be full of static, blurry and may
have multiple ghosts. Digital TV is like a light switch….It is either ON or it is OFF.
3. After the initial setup, you do not receive one or more of your favorite TV channels, try placing the Digital
Antenna in another area and re-scan your TV.
4. Should you still be unable to receive a particular channel, try hooking your unit to Cable TV and re-scan.
DISC-HANDLING CAUTIONS







Hold the disc by the edge so the surface will not be soiled with finger prints. Finger prints, dirt and
scratches can cause skipping and distortion.
Do not write on the label side with a ball-point pen or other writing utensils.
Do not apply benzene, thinner, and liquid that prevents against static electricity.
Be careful not to drop or bend the disc.
Install only one disc on the disc tray.
Do not try to close the disc tray when the disc is not installed properly.
Be sure to store the disc in its case when not in use.
TROUBLESHOOTING
If your DVD player does not seem to be functioning properly, check the items below before you contact an authorized
service center
Symptom
Check
Power does not turn on
or suddenly turns off.
Make sure the AC cord is securely plugged into an AC
outlet. Turn the power off and then back on.
Remote control won't
work
Check that the battery is inserted in the "+" and "-" direction properly. The battery may
be flat. Replace it with a new one.
Check that the signal transmission is directed at the remote control sensor on the DVD
player.
No picture or sound
Remove
thethe
obstacle
between
the remote
controller and remote control sensor.
Check that
A/V cables
are securely
connected.
Check that the disc is a DVD, DVD-RW, AUDIO CD.
Do not use a disc that has scratches or dirt.
Check that the label-side of the disc is facing up.
The pick-up lens of the DVD player may be dirty. Contact the service center for lens
cleaning.
Check that the TV channel is set to VIDEO or AV f viewing with a TV.
No picture
No sound
Check that the LCD display is turned on.
Check that the display panel is open. If it is closed, audio will not be output to the
speakers. Check the volume setting. If set to zero, turn up volume level.
Check that the headphones are plugged into the PHONES
socket. Speakers cannot be used with the headphones.
No picture and sound
Check that the batteries are properly installed and AC cord is properly connected.
Distorted video or sound
Use a disc without scratches or dents.
CAUTION
 The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
 Minimum distances 2.0cm around the apparatus for sufficient ventilation.
 The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
 No exposed flame sources, such as lighted candles, should be placed on the apparatus.
 When the main plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain
readily operable.

Dispose of battery according your local ordinances.
10
Download PDF

advertising