Instructions for Use
Washing machine
Thank you for your confidence in purchasing our washing machine, and congratulations on the
excellent choice.
Your new washing machine meets the requirements of modern treatment of laundry. It is rational in
the consumption of energy, water and washing agents.
Our appliances are friendly to the environment. Some of the materials may be recycled, others
deposited or decomposed. To avoid pollution of environment, once your appliance is no longer
useful, take it to your local authorized waste appliance dealer.
The appliance is intended exclusively for use in households. If the appliance is used for
professional purposes, for profit, or for purposes beyond regular use in a household, or if appliance
is used by a person who is not a consumer, the warranty period equals the shortest warranty period
possible as stipulated by the relevant legislation.
296800
Description of washing machine .................................. 3
Cautions .......................................................................... 4
Installation and connection ........................................... 5
Operation......................................................................... 8
Tips for washing and energy saving .......................... 16
Cleaning and maintenance .......................................... 17
Troubleshooting ........................................................... 20
Tables ............................................................................ 24
2
Description of washing machine
Technical information
(depending on model)
5. Adjustable legs
6. Water outlet hose
7. Water inlet hose
8. Mains power cable
Dimensions (w x d x h): 600 mm x 600 mm x 850 mm
Depth with door open: 106 cm
Weight (net): 78 kg
Nominal voltage: 230 V, 50 Hz
Power: 2300 W
Max. load: 8 kg / 7 kg
Power socket: (230 V, 50 Hz, 10 A)
Water pressure: min. 0,05 MPa, maks. 0,8 MPa
Fuse: 10 A
296800
1. Front panel
2. Detergent dispenser
3. Door
4. Filter lid
3
Cautions
• Be sure to remove transport brackets prior first use of the appliance. Attempted operation of the
blocked machine may result in irreparable damage which is not covered by the manufacturer’s
warranty!
• When connecting your washing machine to water supply, be sure to use brand new water inlet
hose and appropriate sealing gaskets (attached).
• Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be
damaged if frozen.
• Install the washing machine in a perfectly horizontal position, on solid flat concrete floor.
• Follow the instructions for correct installation and water and mains connections.
• Never immerse the end of the drain hose into the draining water.
• Prior starting the washing cycle lock the door by pressing them at the designed spot.
• Door may not be open during the washing cycle.
• We recommend running the self-cleaning program before the first wash in order to remove any
impurities from the washing machine drum (See chapter on” Selecting additional functions”).
• Use only detergents and softeners for machine wash. Manufacturer may not assume
responsibility for any damage and eventual discoloring of gaskets and plastic components as a
consequence of incorrect use of bleach and/or coloring agents.
• For removal of lime residues use such agents with added anti-corrosion agents. Follow the
manufacturer’s instructions. Finish the lime removal by multiple rinsing to remove completely
eventual acid residues.
• Never use detergents containing solvents, since there is a danger of creating toxic gasses which
may damage the machine and result in ignition or explosion.
• Upon completion of washing operation close the water faucet.
• Before any transport block the machine by inserting at least one transport blocking rod. Prior this
operation disconnect the appliance from the mains power!
• Rating plate with basic information is located above the opening of the machine.
• The warranty shall not apply to consumables (bulbs), minor discoloration or deviations of color,
increased noise level as a consequence of appliance age, which does not affect appliance
functionality, and aesthetical deficiencies which do not affect appliance functionality or safety.
• The appliance is manufactured in compliance with all relevant safety standards; however, it is
recommended that persons with impaired physical, motional, or mental abilities, or persons with
inadequate experience and knowledge, do not use the appliance without due supervision. The
same recommendation applies to minors using the appliance.
Before connecting the appliance read these instructions carefully. Repairing the failure
arising from inappropriate connections or use of the appliance is not covered by the
guarantee.
296800
The symbol on the product or on its packaging indicates that this product may not
be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. For more
detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased the
product.
4
Installation and connection
Package removal
In removing the wrapping be careful not to damage the
appliance with a sharp object.
Before connecting the appliance, let it warm up to room
temperature (wait for two hours).
• Our appliances are packed in environmentally friendly
materials which may be recycled, deposited or decomposed
without any threat to the environment.
• To this end all wrappings are marked accordingly.
Removal of transport
brackets
• Move the pipes.
• Loosen screws (A) at the rear of the machine (Fig. 1).
• Remove the brackets (B) (Fig. 1) and slide them into the
groove on the blocking rod (Fig. 2) - the right one should be
turned around.
• Use the brackets to rotate blocking rods for 90° and pull them
out.
• Close the openings with attached plastic pegs.
Save transport brackets for eventual later use.
Fig. 1
Fig. 2
Be sure to remove the transport brackets prior first
use, otherwise the appliance may be permanently
damaged. In such cases the warranty conditions are
void.
• Put the appliance in horizontal position by turning the
adjustable legs. The legs are adjustable up to +/- 1 cm.
After the adjustment tighten the nuts firmly (A) - towards
the bottom of the machine!
Vibrations, moving of the appliance and loud operation
due to incorrect setting of the adjustable feet shall not
be covered by this warranty.
The appliance should be placed on a surface with
concrete base; the surface should be dry and clean in
order to prevent slipping. The adjustable feet should
also be cleaned before installation.
5
296800
Leveling the appliance
• If you have a tumble dryer of the same dimensions, you can
place it on top of the washing machine.
Water inlet connection
To ensure correct operation of the appliance, water
pressure inlet must be between 0,05 and 0,8 MPa.
Minimum water pressure can be established by
measuring the quantity of poured out water. 3 litres of
water must be poured out from completely opened tap
in 15 seconds.
• Take the water inlet hose from the drum and attach the inlet
hose angle extension (1) to the washing machine by screwing
it onto the provided thread (certain models only).
• Insert the gasket with a filter net into the straight inlet hose
attachment nut (2) and screw the nut onto the water tap. (With
some models, the gasket with filter net is already fitted and
any additional fitting into the nut on the straight attachment is
not required).
• In case of hot and cold water connection, connect one hose to
cold and other to hot water faucet as marked at the rear of the
appliance (letters C and H) (C - cold; H - hot)
The inlet hose should be tightened manually, firmly
enough to prevent any leaks. After tightening the hose,
check for any leaks.
Use of pliers, wrenches, or other similar tools is not
allowed when installing the hose, as these tools can
damage the nut thread.
Partial Aqua-stop (water stop system)
In case of damage on the interior pipe, leaking is prevented by
automatic closing system which stops water inlet to the machine.
In such cases display A turns red.
Inlet pipe must be replaced.
Complete Aqua-stop (certain models only)
In case of damage on the interior pipe, leaking is prevented by
automatic closing system which stops water inlet to the machine.
Security system also detects whether there is any water leakage
within the interior of the machine. In such cases washing is
suspended, machine switches on the pump and signals error.
296800
6
Do not immerse the Aqua-stop system inlet pipe into
the water, because it contains the electric valve!
Water outlet connection
• Fix the outlet hose to run into the sink or the bathtub, or
connect it directly to the wall drain outlet (diameter min. 4 cm).
• Wall drain must be installed properly and must enable
occasional cleaning.
• Fasten the outlet hose support with a piece of rope led through
the hose elbow, to prevent the hose from slipping to the floor.
The end of outlet hose should be placed between minimum 60
cm and maximum 100 cm above the floor level.
Connect the appliance to
the mains supply
• Plug the mains power cable to the wall mains socket.
• Required voltage and other information are written on the
rating plate above the door opening of the machine.
The wall socket must be accessible at all times and
must be equipped with an earth lead (in accordance
with the local safety regulations).
The permanent connection must be fitted by an
authorized personnel only.
Damaged mains power cable may be replaced only by
the producer or his authorized personnel.
296800
Never plug the appliance into the electric shaver socket
or hair dryer socket.
7
Operation
A - program selector knob
B - delayed start
C - setting the spinning speed (rpm) / stop
pump
D - quick program or cold wash (depending
on the model)
E - higher water level
F - START / PAUSE button
G - display
Program selector
Signal LED’s:
- washing program stages
• wash
• rinse
• spin
- Child lock
Basic programs
Cotton
+ Pre-wash
Heavy duty
Easy iron
Quick program
15° Tap Water+
Softening
Synthetics
+ Pre-wash
Pumping water
Delicate
Spinning
Wool
Manual wash
Mix
296800
8
Partial programs
Washing procedure
•
•
•
•
•
•
•
Open the door of the machine.
Load the laundry into the drum.
Close the door.
Open the water inlet faucet.
Push the ON/OFF button and select the program.
Add washing and treatment agents (detergent and softener).
Start the operation by pushing the START knob (F).
- Open the door of the machine.
Door is opened by pulling the handle (lever) on the right hand
side of the door towards you.
- Sort the laundry by the type of fabrics.
Do the buttons and zippers, tie the strings and pull out
the pockets.
Very delicate laundry should be put in a special
protective sack.
It is suggested to load the drum with items of different
sizes.
Pay attention to the labels on the clothes, indicating
the recommending washing mode (see table of
textile treatment symbols on the last page of these
instructions).
- Load the laundry into the drum.
Check that the drum is empty.
- Close the door of the appliance.
- Open the water inlet faucet.
- Push the ON/OFF button and select washing program.
Program is selected by turning the program selector (A) from the
“0” position to the desired washing program. The ON/OFF signal
LED indicating particular washing stage for the chosen program
starts flashing. The program selector (A) may be turned in both
directions, and the appropriate program selected according to the
type of laundry washed and the required washing temperature
(see Program Chart for help). You may select basic or partial
programs.
Select additional functions by pressing their relevant knobs (F).
- Selection of basic programs ( , , , , , )
Basic programs represent integral programs containing all
washing stages, including softening and spinning (see Program
Chart). They are selected by turning the program selector (A) to
the appropriate position.
296800
Washing machine
operation
9
Cotton: whites/colored
Normally stained cotton and flax bed linen and underwear, table
cloth, bathroom towels, top garments, etc.
For heavily stained permanent press use the heavy duty
or program with the pre-wash .
program,
For smaller loads (non-delicate cotton, linen, synthetic, and
mixed fabric) and smaller quantities of soiled laundry (laundry
refreshment, laundry wet with perspiration, etc.), we recommend
quick program. This way, you will save both
the use of the
energy and time.
If you wish the laundry not to be excessively creased at the end
of washing, use easy ironing program .
The Cotton 15° program is intended for washing less soiled
laundry, using detergents (washing gels) specially designed for
washing at such temperatures.
Using this program will save you both time and power as water
heater will only be engaged if the water inlet temperature is lower
than 15°C.
Synthetics
Normally stained shirts, blouses and other polyester and
polyamide garments, or a mixture of these fabrics with cotton.
For heavily stained permanent press use program with
pre-wash .
Delicate
This is a program for delicate fabrics (dresses, skirts, blouses)
and curtains.
Wool
Especially gentle program for washing wool and garments made
from mixture of other fabrics with wool, appropriately marked for
machine washing.
Manual wash
Very gentle program concluded with short gentle spin (max. 400
RPM).
It is suitable for washing fabrics from flax, silk, wool or viscose,
marked accordingly for manual wash.
Mix
Special program for washing normally stained colored laundry made
from various resistant fabrics at 30°C.
296800
10
- Selection of additional function (
,
,
,
,
,
,
)
Additional functions alter the basic washing cycle procedure.
Particular function is switched on by pressing the relevant knob.
The selection is confirmed with sound signal and switching on the
signal LED above the selected function. If certain function is not
available for the selected program, signal LED will not illuminate.
The function is switched off by pressing the same button again
- signal LED goes off.
Select the particular function after the selection of the
basic program, but prior pressing the START button (F).
Display (G)
After setting the basic and partial programs and pressing the
START (F) button, washing time is indicated on the display. After
the end of washing, the display reads END.
During washing, the remaining washing time is indicated in hours
and minutes.
If no program is selected and started and no other action is taken
within five minutes after turning on the machine, the display will
be automatically turned off to save energy.
The display will turn on again when you rotate the program
selector dial or press any button.
If no action is taken after the end of the program, the display will
also turn off after five minutes.
Low water temperature, low network voltage, and
smaller loads of laundry may extend the washing time;
the time indicated on the display is constantly adjusted
to account for such conditions.
11
296800
Delayed start
Press the (B) button; the time “00:00” will be indicated on the
display (G). Each time the button is pressed again, the time on
the display will be increased by one hour (maximum delay is 23
hours). After the time has been selected, the LED over the button
lights up (and remains lit). If no other button is pressed in the
following 5 seconds, program duration is indicated on the display.
The function is activated when the START (F) button is pressed.
Time is decreased by minutes. When the count-down is over, the
washing program starts automatically.
• To interrupt or change the delayed start setting, press the
START / PAUSE button.
• To change the delay time, select a new time by pressing the
(B) button. Press START to resume the count-down. To quickly
interrupt the delayed start, press the (B) button and hold it
for three seconds. Press the START button to resume the
program.
Spinning speed (rpm) /
Pump stop
By pressing the (C) button, you can decrease the spinning speed
(in rounds per minute) to “0”. After pressing the button for the
first time, the optimum rpm setting for the selected program is
indicated. By each subsequent press on the button, the spinning
speed is decreased. The last selection is “pump stop”, which
means that laundry remains soaked in the last rinsing water. Use
this function to prevent creasing when you are not able to take
the laundry out of the washing machine immediately after the
washing cycle is over. This function is particularly appropriate for
and delicate laundry . Use of this function is not
synthetics
and manual washing .
recommended with wool
Quick program (selection with a button (D))
• energy-saving program
• appropriate for washing lightly soiled laundry or smaller
quantities of clothes
• reduces washing and rinsing time
• reduces water consumption (with some programs)
• by pressing the key quick program
on the program Cotton
.
30°C, activate the program Cotton 30°C-quick
Cold wash (only available with some models)
For washing lightly soiled or color-sensitive laundry.
When this function is activated, the heaters in the washing
machine are turned off, and the washing program is shortened.
Higher water level (selection with a button (E))
• Improves rinsing, which is particularly important if your skin is
oversensitive to detergents.
• For washing heavily soiled laundry.
296800
Auto-clean program (SterilTub)
Run this program to eliminate any impurities, bacteria, and odor
from the washing machine.
Before running the auto-clean (SterilTub) program, empty the
washing machine drum; there shouldn’t be any clothes in the
washing machine during the auto-clean (SterilTub) program.
Adding a small amount of powder detergent will additionally
improve the effect of the auto-clean (SterilTub) program.
To run the auto-clean (SterilTub) program, rotate the program
selector knob (A) to the position “Cotton 95°C”, then pressing the
(E) (Higher water level) key and hold it for three seconds.
“Cln” and the time remaining until the end of the program will
alternate on the display.
If you do not regularly use washing program with temperatures
over 60°C, it is recommended to run the auto-clean program at
least once per month.
12
- Selection of partial programs (
,
,
)
These are independent programs and may be used when you do
not need the entire washing program. In case you would like to
use more additional programs in a sequence, you must turn off
the appliance prior any new program selection (turn the program
selector to “0” for at least one second).
Conditioning
The program is intended for softening, starching, or impregnating
clean clothes.
Softening program can also be used as an independent or
additional rinse program; in this case, however, do not add any
fabric softener or conditioner.
The program is completed by a spinning cycle at 1,000 rpm.
Spinning speed can be decreased.
Pumping the water out
Use it when the washing program was interrupted or if pump stop
function was engaged, and you only wish to pump the water out
of the drum, without spinning.
Spinning
Aggressive spinning for non-delicate laundry at high spin RMP.
You may engage the reduced spin RPM knob.
- Adding washing and softening agents
(see Tips for washing and energy saving)
• pre-wash compartment
• main wash compartment
• softener compartment
If you do not apply the program which includes the pre-wash
feature, you may add washing detergent directly into the drum,
using the measuring vessel.
When adding softener, be careful to fill the dispenser
only up to the marked level.
296800
Be sure to close the detergent dispenser when
opening/closing the appliance door.
13
Start the operation
• Push the START button (F). Sound signal confirms the start,
the LED indicating particular washing stages stops flashing.
The machine starts operating after a few seconds. If the door
is not properly closed after starting the operation, the washing
stage indicator LED starts flashing again after a few seconds.
When you close the door, the machine initiates the selected
program.
• As each washing stage is completed the relevant washing
stage indicator LED goes off and the subsequent one goes on.
• In case you would like to alter the washing program after the
initiated washing operation, turn the program selector for one
second to the position “0”, followed by the selection of a new
program. Switching the machine off deletes any previously
selected additional functions(i.e. Pump stop), so they have to
be reactivated.
Upon switching OFF, all additional pre-selected
functions are deleted; therefore they must be switchedON again.
- End of washing program
The end of washing program is signalized by flashing washing
progress LEDs. The message “End” is indicated on the display.
• A sound is emitted, indicating that washing machine door can
be opened.
• Take the laundry out of the drum and remove any remaining
particles or foreign bodies from the door seal.
• Leave the door ajar to let the machine dry.
• Close the water inlet tap.
• Turn off the washing machine by rotating the program selector
knob (A) to position “0”.
• After the end of washing program, power supply should be
turned off by pulling the mains cord plug out of the outlet.
Interruptions
• By the user
296800
Selecting PUMP STOP function
position
The program stops when it reaches the PUMP STOP
(if this additional function was previously selected); (washing
machine door is closed throughout the washing process). The
LED over the button (C) starts to flash. Washing can be resumed
by pressing the START (F) button.
was selected, the program stops
If the setting pump stop
is
at the last rinsing cycle and the symbol for pump stop
indicated on the display. The program can be completed by
pressing the START (F) button; in this case, the program will
finish with a spinning cycle, as defined by the program.
14
The program can also be changed by rotating the program
selector knob to “0” and choosing either spinning or only
pumping out the water between additional programs or cycles.
Manual cancellation
The program is cancelled if the program selector knob (A) is
rotated to position “0”. If there is water in the machine, select one
of the additional programs (pumping , spinning ) to empty
the drum and complete the program.
PAUSE knob
By pressing the PAUSE knob (F) program may be suspended
at any time. After certain time you may open the door if there is
no water in the drum, otherwise this is not possible. Program is
continued by pressing the START knob (F).
• Failures
Program is suspended in case a failure occurs. Signal LED’s
are flashing and sound signal is heard (see cf. Failures).
• Power failure
At electric cutout the program is interrupted, however, after the
power supply has been re-established, the program operation
automatically proceeds.
If a power failure occurs when the drum is still full of
water, be careful not to open the door before you pump
the water out.
• Child lock
- To activate the child lock, simultaneously press the spinning
button (C) and short program
(or cold
speed setting
wash ) button (D) and hold them for at least three seconds.
If the child lock is successfully activated, a sound is emitted
and a signal LED lights up. Follow the same procedure to
deactivate the lock.
- As long as the Child lock function is engaged you may not alter
the program or additional functions. You may merely switch off
the machine by turning the program selector (A) to the position
“0”. Child lock remains active even after the appliance is
switched off, and you have to disengage it if you want to select
a new washing program.
• Setting the sound signal
The appliance enables setting a louder sound signal, as well
as turning the sound signal off. Set the function before the
basic program is selected. Set the function by simultaneously
15
296800
Special functions
pressing the button (D) and rotating the program selector knob
(A) from position “0” to the first position for washing program
(clockwise). (“S1”) is indicated on the display, denoting preset
normal sound signal loudness. By pressing the button (D), the
loudness in increased (“S2”); press the button again to turn
the sound signal off (“S0”). The selected setting is stored and
remains in memory even if washing machine is turned off.
Tips for washing and energy saving
• Before washing sort out the laundry according to the type, degree of dirtiness and color
resistance.
• Prior selecting the washing program consult the sewn tab with information on a particular piece
of laundry (see Maintenance Chart on the last page).
• Wash separately the new colored textile products for the first time.
• Wash heavily soiled laundry in small quantities and add more detergent.
• Treat stubborn stains with special stain remover, it will save energy.
• With lightly stained laundry select washing program without pre-wash, use short program and
select lower washing temperature. This way you may save up to 50% of energy.
• Avoid washing too little quantities of laundry because of energy saving and for better
performances of the appliance.
• The largest allowed quantity of dry laundry is indicated in the Program chart.
• Before washing empty the pockets, close zip fasteners, and remove any metal fasteners or
badges that might clog the drain or damage the laundry or drum interior.
• Loosen the stacked laundry prior inserting it into the drum.
• Use only detergents for machine wash.
• Add powder or liquid detergents according to the manufacturer’s instructions.
• If water hardness level exceeds 14°dH degrees, the use of water conditioner is required. Any
damage to the heater due to failure to use a water conditioning agent shall not be covered by
this warranty.
• Chlorine-based whitening agents are not recommended, as it can damage the heater.
Hardness
scale
Degree of hardness
°dH(°N)
m mol/l
1 - Soft
2 - Medium
3 - Hard
< 8,4
8,4 - 14
> 14
< 1,5
1,5 - 2,5
> 2,5
°fH(°F)
< 15
15 - 25
> 25
p.p.m.
< 150
150 - 250
> 250
In case of hard water add detergent according to the Chart for
degree 1 and add appropriate quantity of water softener (see
manufacturer’s instructions).
296800
16
• If you do not apply the program which includes the pre-wash
feature, you may add washing detergent directly into the drum.
• If you use thick liquid softener it is recommended to dilute
it with water, to prevent clogging of dispenser compartment
ducts.
• Washing machine is equipped with the dispenser partition
gate, so you may pour liquid detergent also into the central
compartment (depending on model). If you use powder
detergent the gate is lifted up, and in case of liquid detergent it
is slid down.
• Liquid detergents are intended for main wash only, without
pre-wash.
• Insert particularly delicate linen (stockings, delicate female
underwear, etc.) into the special bag.
• High spin RPM leave less moisture in laundry which dries out
much quicker in the tumble dryer, thereby saving energy.
Do not put clods of detergent into the soap dispenser
as the tube in the washing machine may clog.
Cleaning and maintenance
Disconnect the washing machine from the mains
before cleaning!
296800
• The casing should be cleaned with soft cloth and mild
detergent.
• The interior of the drum and the door gasket is cleaned by
washing at 60°C without laundry and adding half quantity of
detergent.
• Frequent, or predominant, washing at low temperatures, using
liquid detergents, may result in development of bacteria which
causes odor in the washing machine.
To prevent this, we recommend running the auto-clean
(SterilTub) program occasionally (see chapter “OPERATION /
selecting additional functions”).
• If necessary, clean the detergent dispenser. Pull it out from its
casing completely by pressing the flap (see Fig.).
17
• If necessary, clean the cover of the bung under the running
water.
• Wash it under running water using a brush, and dry it. Remove
any leftover dried detergent from the bottom of the casing.
• Clean the entire rinsing area of the washing machine with a
brush, especially the nozzles on the upper side of the rinsing
chamber.
• Clean frequently the water inlet hose screen under running
water.
• After each wash wipe the door rubber gasket. This will prolong
its useful life.
296800
18
• Open the filter lid using flat screwdriver or similar tool.
• Filter needs occasional cleaning, especially following heavily
shaggy or old laundry. Before cleaning, drain any water from
the machine via drain pipe.
• Turn it anti-clockwise, pull it out and clean under running
water.
296800
• Insert the filter back as shown on the picture, and tighten by
turning it in clockwise direction. To ensure good sealing the
gasket surface (A) must be dirt free.
19
Troubleshooting
Washing machine controls the operation of particular functions during washing. If irregularities
are detected, the fault is signaled by displaying a message (Fx) on the display, and by rhythmical
flashing of the LEDs. Simultaneously with the flashing of the LEDs, a sound signal is emitted
several times, in the same rhythm. The machine signals the fault as soon as it is detected, and
the program progress is paused. If the fault is in the heating system, the machine completes the
washing program, but without the heating function.
If the fault is signaled during washing machine operation, the error code and remaining washing
time are indicated alternately on the display.
The fault is indicated until the washing machine is turned off.
Failures:
2 - Two flashes: door is not correctly closed
3 - Three flashes: inappropriate water intake
7 - Seven flashes: inappropriate water outlet.
In these cases, you will be able to remedy the failure by yourself (See Troubleshooting table).
1 - One flash: temperature sensor failure
4 - Four flashes: spinning sensor failure
5 - Five flashes: motor failure
6 - Six flashes: Heater failure
Should any of these failures occur, make note of the failure code, turn off the appliance and repeat
the program. If the failure persists, contact the nearest authorized service centre (the LEDs will
continue to flash until the appliance is turned off).
Various interferences from the environment (e.g. electric devices) may also cause the machine to
signal faults. In such case:
- turn off the appliance and wait a few seconds;
- turn on the appliance and repeat the washing program.
If the fault reoccurs, call the service center.
The warranty does not cover faults caused by interference from the environment (lightning strike,
electric circuit, natural disasters, etc.).
296800
20
FAILURE 2
Washing program does
not start
• At the beginning of the
washing program: on/off
LED is flashing
• During washing: LEDs
periodically flash twice
FAILURE 3
Water does not enter the
machine (after approx.
4 min the machine
reports failure F3 - LEDs
periodically flash three
times).
Water is leaking from the
machine.
The machine moves
during operation.
The machine vibrates
during the spin.
Excessive foaming during
washing.
FAILURE 7
Water is poorly pumped
out or not at all (machine
reports failure F7 - the
LEDs periodically flash
seven times).
Laundry is not properly
spun.
No failure is reported.
Possible cause
Machine is not powered.
Remedy
Check if:
• power in the socket,
• the fuse is OK,
• plug is in the socket.
Door is not properly closed.
Push it towards the machine.
Disturbed water inlet.
Check if:
• the water tap is open,
• inlet pipe net filter is clean.
Push the START button.
Filter is not tightly screwed in.
Inlet pipe is not tightly screwed
to the machine or to the water
faucet.
Outlet pipe fell to the floor.
The machine is not properly
leveled.
Transport brackets are not
removed.
Unevenly distributed laundry,
especially with very small
quantities (for ex. only the
bathrobe).
Excessive measure of
detergent.
Tighten the filter properly.
Tighten the inlet pipe.
Water outlet is clogged
Check if:
• the filter is clean,
• outlet pipe is not jammed,
• the drain is clogged,
• outlet pipe is positioned higher
than 1m.
Push START again
The machine operates normally.
Wash large and small pieces of
laundry together.
The machine switched on the
UKS* function. Because of bad
laundry balance, the machine
has automatically reduced spin
RPM.
Affix the outlet pipe to the drain.
Level the machine with the
adjustable legs.
Remove transport brackets.
This is normal, the machine will
reduce the RPM if vibrations are too
strong.
Wash larger quantity of laundry.
Use washing powder according to
the instructions by the producer and
according to the water hardness
and soiled laundry.
Use only detergents for machine
washing.
296800
Failure
The machine does not
work (indicator LED’s are
not illuminated).
21
Failure
Greasy wads appear on
the laundry.
Possible cause
Too little detergent (laundry was
very greasy).
Laundry is stained after
washing.
You used liquid detergent or
detergent for colored laundry
which does not contain whitener.
It is not the consequence of bad
rinsing, but because of neophosphate detergents containing
non soluble components
(zeolites) for water softening.
Such substances may be
deposited upon the laundry.
Low water flow pressure.
Some detergents may stick to
the dispenser rather hard if it
is wet.
White powdery residues
on the laundry.
Detergent residues in the
dispenser.
Softener is not completely
rinsed, or water is left in
the dispenser dish.
Unpleasant smell in the
washing machine drum.
Washing time is longer
than usual.
Time indicated on the
display is corrected during
the washing cycle.
FAILURE 1
Program temperature not
reached (the machine
reports a failure F1 - the
LEDs periodically flash
once)
FAILURE 4
Spinning rpm not reached
in the selected program
(the machine reports
a failure F4 - the LEDs
periodically flash four
times)
296800
22
Sucking cover is not correctly
positioned or is clogged.
• Remains of fabrics, washing
agent and softener in the filter.
• Development of germs
•
•
•
•
Remedy
Wash the laundry again.
Add more detergent for such soiled
laundry, or use liquid detergent.
Use the detergent containing
whitener.
Immediately rinse the laundry once
again.
• Use liquid detergents which do not
contain zeolites.
• Try removing the residues with the
brush.
• Clean the inlet pipe filter net.
• In case of low water pressure
increase water level.
• Wipe the dispenser prior loading
detergent.
Clean the dispenser and firmly fix
the cover to its place.
• Check whether the filter is clean.
• Run the auto-clean (SterilTub)
program (see chapter: selecting
additional functions)
Low temperature of inlet water. • Washing program time may be up
The machine switched on
to 60% longer; however, this does
the UKS* system because of
not imply a fault in the machine.
uneven laundry load.
Low mains voltage.
There has been a failure in the • Washing time is extended by the
power supply.
power supply down-time.
Temperature sensor
• Turn off the appliance and wait for
disconnected from the electronic
a few seconds;
circuit.
• turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
• rpm sensor disconnected
• Turn off the appliance and wait for
• Motor overload due to too high
a few seconds;
water level (manual addition of • turn the appliance back on and
water) or too big laundry load
repeat the washing program.
If the failure is reported again, call a
• Motor failure
service technician.
Failure
FAILURE 5
Motor operation
interrupted; or motor does
not operate (the machine
reports a failure F5 - the
LEDs periodically flash
five times)
FAILURE 6
Program temperature not
reached (the machine
reports a failure F6 - the
LEDs periodically flash six
times)
Possible cause
Remedy
Motor overload or motor failure.
• Turn off the appliance and wait for
a few seconds;
• turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
• Heater failure
• Inlet water too cold
• Manual addition of water
• Turn off the appliance and wait for
a few seconds;
• turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
* UKS: universal stability control - this function prevents excessive vibrations during spinning.
296800
In case you were not successful in repairing the malfunctions in
spite of the above suggestion chart, call the nearest authorized
service shop.
Repairing the failure arising from inappropriate connections or
use of the appliance is not covered by the guarantee, and the
repair expenses are paid by the customer.
23
Tables
Program chart - 8 kg
Water cons.
(L)
Basic programs
Cotton
8
60
Cotton + prewash
8
60
Cotton - heavy *
8
60
Cotton - easy ironing
4
60
Cotton
8
40
1400
1000
1400
Energy cons.
(kWh)
95
1000 - 1400
Temp. (°C)
8
Spin (RPM)
Max. load (kg)
Cotton
RPM
75
2,45
69
1,36
79
1,65
69
1,38
69
1,27
69
0,75
Cotton
8
30
69
0,39
Cotton - quick 17’
2
30
1000
40
0,17
1400
69
0,18
46
0,97
54
1,30
43
0,56
Cotton - Tap Water+
8
15
Synthetics
3,5
60
Synthetics + prewash
3,5
60
Synthetics
3,5
40
Delicate
3
40
Delicate
3
30
Wool
2
30
1,5
3
1000
58
0,48
58
0,39
800
42
0,20
30
800
50
0,25
30
1000
43
0,35
3,5
1000
15
0,02
Pumping water
8
-
Spinning
8
1400
-
0,03
Manual wash
Mix
700
Partial programs
Softening
* Testing program by EN 60456 with the selection of max. spin
RPM.
296800
24
Program chart - 7 kg
Water cons.
(L)
Basic programs
95
62
2,19
7
60
56
1,17
Cotton + prewash
7
60
66
1,32
Cotton - heavy *
1600
7
60
3,5
60
1000
Cotton
7
40
1600
Cotton
7
30
Cotton - quick 17’
2
30
Cotton - Tap Water+
7
15
Synthetics
3,5
60
Synthetics + prewash
3,5
60
Synthetics
3,5
40
Cotton - easy ironing
Delicate
3
40
Delicate
3
30
Wool
2
30
Manual wash
1,5
Mix
3,5
Energy cons.
(kWh)
7
Cotton
800 - 1600
Temp. (°C)
Cotton
Spin (RPM)
Max. load (kg)
RPM
56
1,19
56
1,14
56
0,67
56
0,35
1000
40
0,17
1600
56
0,18
46
0,97
54
1,30
43
0,56
1000
58
0,48
58
0,39
800
42
0,20
30
800
50
0,25
30
1000
43
0,35
1000
18
0,02
700
Partial programs
3,5
Pumping water
7
-
0,001
Spinning
7
1600
0,03
* Testing program by EN 60456 with the selection of max. spin
RPM.
296800
Softening
25
Quick program
Cold wash*
Basic programs
Higher water level
/
Program
Spinning speed (rpm)
Pump stop
/
Program chart /
Additional functions
Cotton
z
Cotton with prewash
z
Cotton heavy
z
Cotton
z
Cotton - quick 17’
z
z/z
Synthetics with pre-wash
z
z/z
Synthetics
z
z/z
z/z
Delicate
z
z/z
z/z
Wool
z
z/z
z/z
Manual wash
z
z/z
z/z
Mix
z
z/z
z/z
z/z
z/z
z/z
z/z
z/z
z/z
Partial programs
Rinse
z
Softening
z
Pumping water
Spinning
z
z possibility
* depending on model.
296800
26
Maintenance chart
Max.
washing
temp. 95°C
Delicate wash
Whitening
Max.
washing
temp.
40°C
Max.
washing
temp.
60°C
Whitening in cold water
Max.
washing
temp.
30°C
Manual
washing
Washing
not
allowed
Whitening not allowed
Ironing
Hot iron max.
200°C
Hot iron max.
150°C
Hot iron max.
110°C
Ironing not
allowed
Dry cleaning
Dry cleaning in all
solvents
Perchlorinetyhlene
R11, R113,
Kerosene
Dry cleaning in
kerosene, in pure
alcohol and in
R 113
Dry cleaning not
allowed
Drying
Place on
flat surface
Hang wet
Hang
High
temperature
Low
temperature
Tumble drying
not allowed
We reserve the rights to make any changes or mistakes in these operation
instructions.
27
296800
Normal wash
PS PG2 LED 8/7kg
296800/en (12-10)
Download PDF

advertising