SM 720 B
INSTRUCTION MANUAL
BLENDER
Page 1
Read this manual before operation of the appliance!
Dear Customer,
Congratulations on the purchase of your new Defy appliance!
Please read this manual carefully before using your appliance for the first time and then store it
within easy reach for future reference. We trust you will enjoy years of trouble free use.
The user manual:
x This manual will provide you with information on how to safely operate and care for your
appliance in order that you gain the maximum benefit from it.
x Pay particular attention to any safety instructions.
Controls and parts
A Cap/Measuring cup
B Lid opening
C Lid
D Glass jug
E Jug handle
F Blade unit
G Sealing ring
H Motor housing
I Control dial
J Non-slip feet
K Cable storage coil
Special features:
The Defy Blender is equipped
with:
x Powerful 600- watt motor
x 1.5 l high quality glass jug
x Robust stainless steel blades
x Precise speed regulation and
pulse function
x Dishwasher-safe glass jug for
easy and convenient cleaning
x Adjustable speed setting of 5
levels
x Anti slip rubber feet
Page 2
1 Safety and set-up
Please
read this instruction
manual thoroughly prior to using
this appliance! Follow all safety
instructions in order to avoid
damages due to improper use!
Keep the instruction manual for
future reference. Should this
appliance be given to a third
party, then this instruction
manual must also be handed
over.
x
This appliance is intended for
private domestic use only and
is not suitable for professional
catering purposes. It should
not be used for commercial
use.
x Do not use the appliance in the
bathroom.
x Check if the mains voltage on
the rating label corresponds to
your local mains supply. The
only way to disconnect the
appliance from the mains is to
pull the plug from the wall
socket.
x For additional protection, this
appliance should be connected
to a household current fault
protection circuit breaker of no
more than 30 mA. Consult an
electrician for advice.
x Do not immerse the motor
housing, power cord, or power
plug in water or any other
liquids. Do not hold it under
running water. Only the lid and
the glass jug can be cleaned
safely with water and washing
up liquid in the dishwasher.
x Disconnect
the power plug
after using the appliance,
before cleaning the appliance
or leaving the room and if a
fault occurs. Do not disconnect
the plug by pulling on the cord.
x
Do not squeeze or bend the
power cord and do not rub it on
sharp edges in order to prevent
any damage.
x Keep the power cord away
from hot surfaces and open
flame.
x Do not use an extension cord
with the appliance.
x Never use the appliance if the
power cord or the appliance is
damaged.
x Our
Household Appliances
meet
applicable
safety
standards, thus if the appliance
or power cord is damaged, it
must be repaired or replaced
by an authorised service centre
to avoid any dangers. Faulty or
unqualified repair work may
cause danger and risks to the
user.
x Do not dismantle the appliance
under any circumstances. No
warranty claims are accepted
for
damage
caused
by
improper handling.
x Always keep the appliance out
of the reach of children.
x This appliance is not intended
for use by persons (including
children)
with
reduced
physical, sensory or mental
capabilities
or
lack
of
experience and knowledge,
unless they have been given
supervision
or
instruction
concerning the use of the
appliance
by
a
person
responsible for their safety.
x Children should be supervised
to ensure that they do not play
with the appliance.
Page 3
Safety and set-up
x
Do not leave the appliance
unattended while it is in use.
Extreme caution is advised
when the appliance is being
used near children and people
with limited physical, sensory
or mental capabilities.
x Before using the appliance for
the first time, clean all parts
which come into contact with
food carefully. Please see
details in the “Cleaning and
Care” section.
x Never operate or place any
part of this appliance on or
near hot surfaces such as a
gas burner, hotplate or heated
oven.
x Do not use the appliance for
anything
other
than
its
intended use.
x Never use the appliance in or
near
to
combustible
or
inflammable
places
and
materials.
x Operate the appliance only
with the delivered parts.
x Do not use the appliance with
damp or wet hands.
x Always use the appliance on a
stable, flat, clean, dry, and non
slip surface.
x Make sure that there is no
danger that the power cord
could be accidentally pulled or
that someone could trip over it
when the appliance is in use.
x Position the appliance in such
a way that the plug is always
accessible.
x
The blade unit is very sharp!
Handle the blade unit with
utmost care, especially during
cleaning, in order to avoid
injuries.
x Do not use the appliance if the
blade unit is damaged or
shows signs of wear.
x Never clean the appliance with
your bare hands.
x Never try to use the appliance
without the lid.
x Do not attempt to remove the
lid until the blades have
completely stopped.
x A spatula may be used to
remove the ingredients from
the glass jug. The appliance
must be switched off before
doing this.
x Never operate the appliance
for longer than necessary for
processing the food.
x Remove
bones and stones
from food to prevent the blade
unit and the appliance from
being damaged.
x This appliance is only intended
for short periods of use and
should only be in continuous
use for maximum 1 minute.
After use, let the appliance
cool down sufficiently.
x Do not crush big pieces of ice
cubes with the appliance,
crush only small ice cubes.
x Switch off the appliance and
disconnect from supply before
changing
accessories
or
approaching parts that move in
use.
The manufacturer strives for continuous improvement. For this reason, the
text and illustrations in this manual are subject to change without notice.
If the appliance is damaged in any way do not use it. Report the damage to
your dealer who will take the necessary corrective action.
Page 4
2
Operation
Preparation
Caution
Switch off the appliance and disconnect from
the
power
supply
before
changing
accessories or approaching parts that move
in use.
1 Remove all packaging and stickers
materials and dispose of them according to
the applicable legal regulations.
2 Take the entire unit of the motor housing H
and place it on a level surface, e.g. on the
kitchen counter.
3 Now set the glass jug D with the opening
facing down on a level surface.
4 Remove the blade unit F carefully by
turning it counter clockwise and lifting it by
holding it from the sides of the unit.
Caution
Do not remove the blade unit by lifting it
from the blades.
The blade unit is very sharp! Handle the
blade unit with utmost care, especially
during cleaning, in order to avoid injuries.
5 Clean all parts, with the exception of the
motor housing as described in “Cleaning and
Care”.
6 Then re-assemble the table blender in the
reverse order.
7 Put the glass jug D on the motor housing
H.
Note
Make sure that the notches on the bottom of
the glass jug fit those in the motor housing.
8 Cut the food into small pieces before using
the appliance.
Page 5
Operation
Blending
1 Place the device on an even and dry
surface. The non-slip feet J ensure the
stability of the appliance.
2 Make sure that the power cord is
disconnected from the power supply and the
control dial I is on “0” before putting food
into the glass jug D.
3 Take the glass jug D from the motor
housing H by lifting the glass jug D upwards
and open the lid.
4 Now put the ingredients to be blended in
the glass jug D. The ingredients should only
be about 2-5 cm long.
Notes
Add water to ensure the blender functions
smoothly.
Mix 3 units of hard food and 2 units of water
in order to have a smooth table blender
experience. (i.e: 60 gr hard food 40 ml
water).
Caution
Do not put or blend hot foods or liquids in the
glass jug. If you process soup, make sure
that the liquid temperature does not exceed
40°C.
To process crushed ice, we suggest you to
start with three quarters of ice in the jug and
add 15 ml of cold potable water.
Don´t try to crush ice without adding water to
the jug.
Never let the table blender operate while
empty (without food).
Never let the jug blender operate without the
glass jug on the motor housing.
5 Close the lid C. Make sure that the cap/
measuring cup A is inside the lid opening
and is secured.
6 Place the glass jug D upright onto the
motor housing H.
Caution
x Never move or turn the glass jug after it is
properly seated in the place.
7 Connect the power plug to a suitable
power outlet.
8 The cutting speed can be variably adjusted
with the control dial I.
Notes
x To operate the blender at the low speed,
turn the control dial I to “1”.
x If you want to blend with a higher speed,
turn the control dial I to the desired speed
level (2-4).
x For short pulses of blending with a high
speed, turn the control dial I to “P”. When
you release the control dial I, the blender
will stop and return to “0” automatically.
x If ingredients are to be added during the
blending process, then add them through
the opening in the lid B. To do this, take
out the cap/measuring cup A.
9 After the desired consistency of the
blended food has been reached, turn the
control dial I to 0 to switch off the blender.
Caution
x Never run the blender for longer than 1
minute, otherwise it would overheat.
x After running the appliance for 1 minute,
let it cool down before using it again.
x Be sure the motor is switched off and has
completely stopped before removing glass
jug D from the motor housing H.
x Do not place any utensil (scraper, fork,
etc.) in the glass jug while blender is
operating.
10 Pull the power plug out of the power
outlet.
11 Take the glass jug D off from the motor
housing H by lifting the glass jug upwards
(do not try to rotate it) and open the lid C.
12 Take off the lid and pour the mixture into
glasses or other containers.
Page 6
3
Information
Tips for blending
x To add ice cubes to mixtures while the
x
x
x
x
x
x
blender is operating, add one cube at a
time through cap A. Wait a few seconds
before adding the next ice cube so that
the blender can properly blend the ice.
To add food while the blender is
operating, remove the cap A and drop the
ingredients through the opening. Be sure
to cut the food into about 2-5 cm pieces to
fit through the opening. Replace the cap A
when
you
have
finished
adding
ingredients.
When blending solid foods, such as raw
vegetables, cooked or uncooked meats
and fruits always cut them into no larger
than 2-5 cm pieces before placing them
into the glass jug. Blend no more than 2
cups of these foods at a time. This will
speed the blending process and reduce
wear on the blending blades.
Always place liquid ingredients in the
glass jug first, unless a recipe specifically
states otherwise.
To blend beverages, place all ingredients
in the glass jug at the same time.
Avoid overblending. Usually, you will need
to blend for a few seconds.
Overblending may cause food to become
mushy.
Page 7
Information
Cleaning and care
Caution
Never use petrol, solvents, abrasive
cleaners, or metal objects and hard brushes
to clean the appliance.
The blades of cutter unit are very sharp!
Handle the blades with utmost care in order
to avoid injuries.
Never clean the appliance with your bare
hands.
Clean the blender after each use. Do not let
any food remnants harden on and inside the
blender. This will make it more difficult to
clean it later.
Do not use boiling water. The blade
assembly bearings have been designed
with a lifetime lubricant; exposure to
boiling water may damage these bearings
and shorten the life of the blender.
1 Turn the appliance off and disconnect it
from the wall socket.
2 Allow the appliance to cool down.
3 Remove the glass jug D from the motor
housing H. Rinse with water to remove any
large food particles that may have
accumulated in the glass jug.
4 Replace the glass jug D on motor housing
H.
5 Place 1 to 1 ½ cups warm water with some
drops of mild cleanser into the glass jug D
and switch to speed “4” for a few seconds.
Remove the glass jug from motor housing
and rinse with water. Repeat as necessary.
Note
Do not immerse the motorized base or blade
unit in liquid, or place them in the
dishwasher. Only the lid and the glass jug
may be immersed and placed in the
dishwasher.
6 Use a damp soft cloth and some mild
cleanser to clean the exterior of the
appliance.
7 Wipe the blender base, cutter unit F and lid
with a lint free cloth before the next usage.
Environmental note
This appliance has been made from high
quality materials and parts which can be
reused and are suitable for recycling.
Do not dispose of the appliance with normal
household waste at the end of its service life.
Consult your local authorities for disposal
information and facilities available.
Help protect the environment by
recycling used appliances.
Technical data
This appliance conforms to the
European directives 2004/108/
EC, 2006/95/EC, 2009/125/EC
and 2011/65/EU.
Power supply: 220-240 V~, 50/60 Hz
Power: 600 W
Technical and design modifications
reserved.
Warning: Repairs must be
carried out by authorised
persons only. Repairs carried
out by incompetent persons
create a user risk.
DANGER! Always disconnect
the plug from the wall socket
before any maintenance or
cleaning.
Record in the space below the listed information
for future reference.
Please register your product at
SERIAL NUMBER……………………………..
DEFY APPLIANCES (PTY) LTD
P.O.BOX 12004
JACOBS
DURBAN
4026
SOUTH AFRICA
www.defy.co.za
DATE OF PURCHASE………………………..
PURCHASED FROM…………………………..
…………………………………………………...
Page 8
4
Branches
If you have followed the instructions and still have a problem, contact the
customer care line on 086 100 3339. They will be able to advise you on any aspect
of the appliance.
South African Branches:
Sub-Saharan Africa Branches:
BLOEMFONTEIN
160 Long Street, Hilton, Bloemfontein 9301
Tel: 051 400 3900
Bloemfontein.Service@defy.co.za
ZAMBIA: SOUTHGATE INVESTMENTS LTD
Plot 1606, Sheki Sheki Road
P.O. Box 33681
Lusaka, 10101, Zambia
Tel: +260 0211 242332/3
Fax: +260 0211 242933
sgiservicecentre@microlink.zm
CAPE TOWN
5A Marconi Rd. Montague Gardens, 7441
Tel: 021 526 3000
CapeTown.Service@defy.co.za
DURBAN
135 Teakwood Road, Jacobs,
Durban, 4052
Tel: 086 100 3339
Durban.Service@defy.co.za
EAST LONDON
Robbie de Lange Road, Wilsonia,
East London, 5201
Tel: 086 100 3339
EastLondon.Service@defy.co.za
JOHANNESBURG
Cnr. Mimetes & Kruger Sts. Denver ext.12
Johannesburg, 2094
Tel: 011 621 0200 or 011 621 0300
Gauteng.Service@defy.co.za
POLOKWANE
87 Nelson Mandela Drive, Superbia 0699
Tel: 0152 92 1166 / 7 / 8 / 9
Polokwane.Service@defy.co.za
PORT ELIZABETH
112 Patterson Road, North End, Port Elizabeth
6001
Tel: 041 401 6400
PortElizabeth.Service@defy.co.za
PRETORIA
Block A1 Old Mutual Industrial Park,
Cnr. D.F.Malan Drive & Moot Str. Hermanstad,
0082
Tel: 012 377 8300
Pretoria.Service@defy.co.za
NAMIBIA: ATLANTIC DISTRIBUTORS (PTY)
LTD
10 Tienie Louw Street, Northern Industrial Area
P.O. Box 21158, Windhoek, Namibia
Tel: (061) 216162
Fax: (061) 216134
atlantic@mweb.com.na
ZIMBABWE: TRADECOMAFRICA
Trade Com Africa, 183 Loreley Crescent
Msasa, Harare, Zimbabwe
Tel: +263 4 486165/6
Cell: +263 772 469010
Cell: +263 772 469011
BOTSWANA: RAY MORGAN AGENCIES
RMA Service Centre, Plot 48, East Gate
Gaborone International Commerce Park
Kgale View, Gaborone
Botswana
Tel: +267 390 3996 / 390 3912
Fax: +267 318 7376
Cell: +267 7134 6539
service@rma.co.bw; raja@rma.co.bw
SWAZILAND: LYNDS DISTRIBUTORS
P.O Box 716, Mbabane, Swaziland, H100
Tel: (00268) 2515 4310/8
Fax: (00268) 2518 4318
MOZAMBIQUE: COOL WORLD. LDA
Rua da Resistencia No. 97B R/C
Cell: +258 84 44 61 234
coolworldlda@hotmail.com
Nosso Show Room
Av: da Industrias, Parcela No.735 * 735A
Machava, Maputo
OTHER AREAS ARE SERVICED BY OVER 200 AUTHORISED SERVICE AGENTS.
PLEASE CONSULT THE CUSTOMER CARE LINE ON 086 100 3339 FOR DETAILS.
Page 9
5
Warranty
This certificate is issued by DEFY APPLIANCES (PTY) LIMITED manufacturers of Defy
and Ocean products, hereinafter the Company, to the original purchaser only, of the
appliance described on the certificate and shall constitute the only warranty given in
respect of this appliance.
The Company warrants to the original purchaser that for a period of ONE YEAR from date
of purchase the appliance is free from defect under normal domestic use, both in
workmanship and material, subject to the following conditions.
1. Carry-in service. Small appliances are repaired in our service centres and are not
collected from the customers home. Faulty units must be delivered to the purchasing
dealer or to the nearest Company Service Centre for warranty repairs.
2. Vitreous enamelware, fuses and lamps are specifically excluded from these warranties. It
is an express condition of these warranties that the purchaser takes due care and
attention in the use and maintenance of the appliance. Abuse, misuse in conflict with
operating instructions, connection to incorrect voltages and subjection to commercial use
shall release the Company from its obligations.
3. This warranty shall become void and cease to operate if the appliance is dismantled by,
or any repairs to the appliance are effected by any persons not duly authorised by the
Company, or if substitute parts not approved by the Company are used in the appliance,
or if the serial number of the appliance is removed.
4. The Company shall not be responsible for damages resulting from fire, flood, civil
disturbances or any Act of God. The Company shall not, in terms of these warranties be
responsible nor held liable for any consequential loss or damage of any kind caused by or
due to the failure or malfunction of the appliance. The Company shall not be responsible
for damages caused by insect and/or animal infestation.
5. The Company shall not be responsible for transportation or other costs other than those
incurred within the provisions of Point 1 of this Certificate.
6. For warranties in the Republic of South Africa and Sub-Saharan Africa, please
contact your nearest Defy office. Please refer to the previous page for respective
South African branches and Sub-Saharan Africa branches.
7. Where service is requested under warranty and no fault or defect can be found by the
Company, all costs incurred will be for the purchaser's account.
8. This Certificate as well as your invoice will serve as proof of purchase. For the purpose
of warranty, it will be essential to produce this Certificate and invoice. Failure to do so, will
render the purchaser liable for service costs.
KEEP THIS CERTIFICATE AND SALES INVOICE AS PROOF OF
PURCHASE FOR WARRANTY PURPOSES.
Page 10
Download PDF
Similar pages
BLF01CR EU BLENDER
BLF01**AU Blender
BLF01CRAU New product 50's Retro style
Grundig SM 5040
Severin KA 9244 coffee maker
Severin KA 4156
Severin KA 4157
Severin KA 4055
Severin KA4053 coffee maker