User’s Manual
road series
Antes de utilizar el equipo, lea la sección
“Precauciones de seguridad” de este manual.
Conserve este manual para futuras consultas.
Before operating the device, please read the
“Safety precautions” section of this manual.
Retain this manual for future reference.
CONTENTS
SAFETY PRECAUTIONS
3
WARRANTY
4
DECLARATION OF CONFORMITY
5
INTRODUCTION
6
6a7
CONFIGURATIONS
8
LINE DRAWINGS
9 a 11
AMPLIFIER
Description
ON / OFF
Overload indicators
Overheating
Equalisation
Low mains voltage
Current consumption
Troubleshooting
SPECIFICATIONS
12
ACCESSORIES
12
TRD-2 & TRD-6
13
APPENDIX
Line connections: unbalanced and balanced
Manual del Usuario/ road series / User’s Manual
road series
Precauciones de Seguridad
Safety Precautions
Cajas acústicas activas / Self-powered loudspeaker enclosures
El signo de exclamación dentro de un triángulo indica la
existencia de importantes instrucciones de operación y
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.
ATENCIÓN: Es un producto clase A, por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1,
E2, E3 ó E4.
The exclamation point inside an equilateral triangle is intend to
alert the users to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product. Heed all warnings. Follow all
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment
this product may cause radio interferences in which case the
user may be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments
according to EN55103-2.
Do not remove mains connector ground, it is dangerous and
illegal. Class I device. The product must be connected to mains
socket outlet with protective earth connection. Only use this
equipment with an appropriate mains cord for your country.
No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I. El producto debe ser
conectado a un enchufe con toma de tierra. Sólo use este
equipo con el cable de red de alimentación adecuado para su
país.
El signo del rayo con la punta de flecha, alerta contra la
presencia de voltajes peligrosos no aislados. Para reducir el
riesgo de choque eléctrico, no retire la cubierta.
The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.
No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat. The
circulation of air through the heatsink must not be blocked.
No exponga este equipo a la lluvia o humedad. No use este
aparato cerca del agua (piscinas y fuentes, por ejemplo). No
exponga el equipo a salpicaduras ni coloque sobre él objetos
que contengan líquidos, tales como vasos y botellas.
Equipo IP-20.
Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.
Equipo diseñado para funcionar entre 15ºC y 45ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta trasera
(según IEC 60065:2001). Si debe sustituir el fusible preste
atención al tipo y rango.
El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.
Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.
Para desconectar el dispositivo debe usar el enchufe.
Desconecte este aparato durante tormentas eléctricas,
terremotos o cuando no se vaya a emplear durante largos
periodos.
No emplace altavoces en proximidad a equipos sensibles a
campos magnéticos, tales como monitores de televisión o
material magnético de almacenamiento de datos.
Do not expose this device to rain or moisture. Do not use this
apparatus near water (for example, swimming pools and
fountains). Do not place any objects containing liquids, such as
bottles or glasses, on the top of the unit. Do not splash liquids
on the unit. IP-20 equipment.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.
Working temperature ranges from 15ºC to 45ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the rear label (according to IEC 60065:2001). If the
fuse needs to be replaced, please pay attention to correct type
and ratings.
The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.
If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.
To disconnect the device, you should use the mains plug. Unplug
this apparatus during lightning storms, earthquakes or when
unused for long periods of time.
Para las cajas con vaso para trípode, la altura máxima de
seguridad desde el suelo a la base de la caja montada sobre
trípode modelo TRD-2, con pies a 55 cm del eje del trípode, es:
For enclosures with tripod socket, the maximum safety height
from floor to bottom of enclosure when mounting on a TRD-2
tripod, with legs spread 55cm from the central pole, is:
Do not place loudspeakers in proximity to devices sensitive to
magnetic fields such as television monitors or data storage
magnetic material.
road 12A ------------------------->135 cm
road 15A ------------------------->130 cm
El colgado del equipo sólo debe realizarse utilizando los herrajes
de colgado recomendados y por personal cualificado. No
cuelgue la caja de las asas.
road 12A ------------------------->135 cm
road 15A ------------------------->130 cm
55 cm
The appliance should be flown only from the rigging points and
by qualified personnel. Do not suspend the box from the
handles.
No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el equipo se haya dañado de alguna
forma, como que haya caído líquido o algún objeto en el interior
del aparato, haya sido expuesto a lluvia o humedad, no funcione
correctamente, haya recibido un golpe o su cable de red esté
dañado.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
Limpie con un paño seco. No use limpiadores con disolventes.
Clean only with a dry cloth. Do not use any solvent based
cleaners.
Reselling of the product is only possible if the user manual is
aviable. Any changes made to the product have to be
documented in writing and passed on to the buyer in the event
of resale.
La reventa del producto sólo es posible incluyendo el manual de
usuario. Cualquier cambio producido en el producto tiene que
ser documentado por escrito y aprobado por el comprador en el
momento de la reventa.
Manual del Usuario / road series / User’s Manual
3
GARANTÍA
Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.
Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.
Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.
Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.
Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.
WARRANTY
All D.A.S. products are warrantied against any manufacturingdefect
for a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.
4
Manual del Usuario/ road series / User’s Manual
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
D.A.S. Audio, S.A.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).
Declara que la serie road:
Declares that road series:
Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:
l
Directiva de Baja Tensión (Low Voltage Directive)
2014/35/UE
l
Directiva de Compatibilidad Electromagnética (EMC)
2014/30/UE
l
Directiva RoHS
2011/65/UE
l
Directiva RAEE (WEEE)
2012/19/UE
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
l
EN 60065:2014.- Audio, video and similar electronic apparatus. Safety
requirements.
l
EN 55032:2012.- Electromagnetic compatibility of multimedia equipment.
Emission requirements.
l
EN 55103-2:2009.- Electromagnetic compatibility. Product family
standard for audio, video, audio-visual and entertainment lighting control
apparatus for professional use. Part 2:Immunity.
l
EN 50581:2012.- Technical documentation for the assessment of
electrical and electronic products with respect to the restriction of
hazardous substances.
Manual del Usuario / road series / User’s Manual
5
INTRODUCTION
The D.A.S. Road series stage monitors have been designed to enhance the artist's performance and
consequently the success of the event. The new Road series employs a two-way configuration and a
reduced enclosure size to provide a low profile design without sacrificingpower handling or sound quality.
The road is a 2-way powered stage monitor
that incorporates a 12R4 cone loudspeaker for
road 12A, or 15R4 for road 15A, for bass
reproduction. High frequencies are handled by an
M-75 compression driver with 1.5” exit, a 3”
titanium diaphragm and EFW voice coil. The 60° x
40° rotatable horn allows for high frequency
coverage options when the situation calls for it.
The biamplified system (Low:550W +
High:220W) uses a 3th generation Class “D”
amplifier. With a 24-bit DSP providing FIR (Finite
Impulse Response) filters, unparalleled control over
critical signal parameters can be accomplished. It
allow two EQ presets: Monitor & Main.
road 12AL
The monitor’s low profile design, side mounted
handles, and strategically located skid plates allow
for ease of use onstage. Hidden connector plugs
and indicator LEDs offer an undistractive reference
for the artist and a clean stage appearance.
Housed in the birch plywood enclosure finished
with durable Iso-Flex black paint and sturdy
speaker grilles for “performer’s abuse”, the road is
available in Left or Right hand versions. For PA
use, the system has a pole mount socket, in one
of its handles.
road 15AL
CONFIGURATIONS
Mixer
POWER
SUPPLY
LINK
POWER
SUPPLY
road 12AL
or
road 15AL
road 12AR
or
road 15AR
POWER
SUPPLY
HF drivers outside
(Recommended).
LINK
road 12AL with road 12AR
or
road 15AL with road 15AR
6
Manual del Usuario/ road series / User’s Manual
CONFIGURATIONS (cont’d)
road 12A
Horizontal Directivity of two units, HF drivers outside
(Recommended).
0
-60.00
Deg
dB
-40.00
-10
-20.00
-20
0.00
-30
20.00
-40
40.00
60.00
50
100
200
500
1k
2k
5k
10k
-50
20k Hz
Horizontal Directivity of two units, HF drivers inside.
0
-60.00
dB
Deg
-10
-40.00
-20.00
-20
0.00
-30
20.00
-40
40.00
-50
60.00
50
100
200
500
1k
2k
5k
10k
20k Hz
road 15A
Horizontal Directivity of two units, HF drivers outside
(Recommended).
0
-60.00
Deg
dB
-40.00
-10
-20.00
-20
0.00
-30
20.00
-40
40.00
60.00
50
100
200
500
1k
-50
2k
5k
10k
20k Hz
Horizontal Directivity of two units, HF drivers inside.
0
-60.00
Deg
dB
-40.00
-10
-20.00
-20
0.00
-30
20.00
-40
40.00
60.00
50
100
200
500
1k
2k
Manual del Usuario/ road series / User’s Manual
5k
10k
-50
20k Hz
7
LINE DRAWINGS
ALL DIMENSIONS IN MILIMETERS
648
324
road-12AL
420
Front View
Rear View
Left View
648
324
road-12AR
420
Front View
Rear View
Left View
747
371
road-15AL
480
Front View
Rear View
Left View
747
8
371
road-15AR
480
Front View
Left View
Manual del Usuario/ road series / User’s Manual
Rear View
AMPLIFIER
Description
7
Road 12A
D.A.S. AUDIO S.A. (Valencia), MADE IN SPAIN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PRESET
3
LIMIT
4
SIGNAL
5
ON
LOOP THRU
AC INPUT
INPUT
MONITOR
AC OUTPUT
6
MAIN
1
9
MAX. 10 UNITS IN PARALLEL
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE
8
2A 50Hz/60Hz
CAUTION
N1918
230V
1) INPUT :
1/4” Jack+XLR combined socket-type input
signal connector. This is a balanced connector just
like the LOOP THRU connector with the following
pin assignments:
1 or S =GND (ground).
2 or T =(+) Non inverted input.
3 or R =(-) Inverted input.
2) LOOP THRU :
XLR-type output signal connector for
connecting several units together and sending
them all the same signal.
3) LIMIT :
Red LED indicates amplifier saturation.
Amplifier limiter indicator lights.
4) SIGNAL :
Green LED indicates signal presence.
5) ON :
Green LED indicates that the unit is ON.
2
Typical road series amplifier
6) PRESET :
Button for switching between two types of frequency response (see below curves).
7) road model.
8) AC INPUT :
PowerCon NAC3FCA mains connector (inserted, rotated and locked for ON). Only use this equipment
with an appropriate mains cord.
9) AC OUTPUT :
PowerCon NAC3FCB connector for AC loop thru allows other units to be powered. Only use this
equipment with an appropriate mains cord. Don’t exceed the recommended number of
connected devices (see unit’s label).
120.0
dBSPL
MAIN
MONITOR
110.0
100.0
90.0
80.0
70.0
10
100
1k
10k
Hz
20k
10k
Hz
20k
road 12A Frequency Response
120.0
dBSPL
MAIN
MONITOR
110.0
100.0
90.0
80.0
70.0
10
100
1k
road 15A Frequency Response
Manual del Usuario/ road series / User’s Manual
9
ON / OFF
A sound system should be switched on
sequentially. Switch on the self-powered units last
in your sound system (switch on the subwoofer
before the mid-high system). Switch on the sound
sources such as CD players or turntables, then the
mixer, then the processors, and finally the selfpowered unit. If you have several units, it is
recommended that you switch them on
sequentially one at a time.
Follow the inverse order when switching off,
turning self-powered units off before any other
element in the sound system.
Disconnect the device by removing the mains
connector from the mains socket. The mains
connector and mains socket must always be freely
accessible and never covered or blocked in any
way. The mains cable can be detached from the
device by disconnecting the Neutrik PowerCon
connector. Always disconnect the device by
removing the mains connector from the mains
socket before detaching the mains cable at the
Neutrik PowerCon connector.
IMPORTANT: Do not disconnect the unit when
it is playing music.
Ensure that the device is disconnected from
mains by observing that the ON LED is turned off.
Please note that the ON LED can stay on for
several seconds after the mains power has been
disconnected.
Overload indicator
This device has an indicator (LIMIT LED) that
lights when the signal is excessive.
The indicator should not be lit continuously.
This distorts the signal (quickly fatiguing your ears)
and may damage the speakers. Therefore, it is
recommended that you never work with this LED
on; at most it should blink only occasionally.
Overheating
This equipment does not normally overheat
during normal conditions of use. When overheating
occurs, the unit protects itself. You should then
find out why and if necessary contact an
authorised dealer for Technical Assistance.
Normally it is enough just to let the unit cool
down after you have corrected the problem so that
the system functions properly again.
10
Equalisation
The unit does not need extreme settings of
equalisation to produce quality sound. Avoid high
levels of gain on the equalisers. Gain values above
+3 dB on a console’s EQ are not recommended.
Low mains voltage
If mains voltage falls below the shutdown
voltage for the unit, it will stop playing. When
acceptable levels are regained, the unit will switch
back on automatically.
The power supply allows the system to
function using two voltage ranges: from 90V to
128V, for 115V AC version, and from 180V to
256V, for 230V AC version.
Therefore the current consumed by the first
range (90 to 128V) is double the second to
achieve the same acoustic power level.
Current consumption:
Pink Noise
Mains 230 Vrms
Potenciamáxima
2A
1/3 Potencia
1.7A
1/8 Potencia
0.95A
Sin carga
0.2A
Note
E1.- Residential.
E2.- Commercial and light industrial.
E3.- Urban outdoors.
E4.- Controlled EMC environment and the rural
outdoors environment.
This product should only be used in E1, E2, E3
or E4 environments, in accordance with standard
EN55103-2 (Electromagnetic compatibility. Product
family standard for audio, video, audio-visual and
entertainment lighting control apparatus for
professional use. Part 2: Immunity.)
Do not cover the amplifier's radiator nor
obstruct its ventilation.
For consumption reasons, it is important not to
connect the equipment to the same line as the
lighting systems, thus avoiding interruptions or
sudden drops in lighting intensity.
Manual del Usuario/ road series / User’s Manual
Troubleshooting
PROBLEM
CAUSE
SOLUTION
No sound from the unit.
The SIGNAL presence LED
indicator(s) do(es) not light up.
1- The signal source is sending
no signal.
1- Check that the mixer or sound
source is sending signal to the UNIT
.
2- Defective cable.
2- Check that the cable from the
sound source to the UNIT is
connected correctly. Replace the
cable if defective.
Full power cannot be obtained.
The LIMIT LED indicator(s) never
light(s) up.
1- The signal source does not have
a hot enough output.
1- If using a mixer, use the balanced
output if available. Use a pr
ofessional
mixer with a hotter output.
Sound is distorted.
The LIMIT LED indicator(s) is/ar
e not
on, or only light up occasionally
.
1- The mixer or signal source
is distorting.
1- Turn mixer channel gains down.
Check that none of your signal
sources are distorting.
Sound is distorted and very loud.
One or more LIMIT LED indicators
light up.
1- The system is overloaded and
has reached maximum power.
1- Turn down the mixer's output.
Hum or buzz when a mixer
is connected to the unit.
1- The console probably has
un-balanced outputs. You may
be using an incorrect un-balanced
to balanced cable.
1- Read the appendix of this manual
to make a correct un-balanced to
balanced cable.
2- The mixer and the powered
speaker are not plugged into
the same mains outlet.
2- Connect the mixer and the unit
to the same mains outlet.
3- The audio signal cable is too
long or too close to an AC cable.
Hum or buzz when using lighting
controls in the same building.
3- Use a cable that is as short as
possible and/or move the audio
signal cable away from mains cables.
1- Move the audio signal cable away
1- The audio signal cable is too
long or too close to the lighting cable. from lighting cables. Try to find out
at what point the noise is leaking
into the system.
2- On a sound system with threephase AC, the lighting equipment
2- Connect the sound system to
and the UNIT are connected to
a different phase than the lights.
the same phase.
You may need the help of an electrician
The power on LED indicator(s) do(es)
1 Bad or loose AC connection to
not light up when the power connector the UNIT or the mains outlet.
is rotated and locked at the
ON (LOCK) position.
2 Faulty AC cable.
3
Blown Fuse.
Manual del Usuario/ road series / User’s Manual
1-
Check you connections.
2- Check the cables, connectors
and AC power with a suitable
mains tester.
3- Replace fuse on fuse holder with
one of the same type. If it blows again,
take the unit to a service centr
e.
11
SPECIFICATIONS
Model
Nominal LF Power Amplifier
Nominal HF Power Amplifier
Input Type
Input Impedance
Sensitivity
On-axis Frequency Range (-10dB)
Maximum Peak SPL at 1m
HF Horn Coverage Angles (-6dB)
Enclosure Material
Finish
Transducers / Replacement Parts
Connectors
AC Power Requirements
Current Draw (1/3 power @ 230V)
Shut-down Voltage
Dimensions (H x W x D)
Weight
Accessories (optional)
road 12A
road 15A
550W
550W
220W
220W
Balanced
Balanced
Line: 20 kohms
Line: 20 kohms
Line: 1.55V (+ 6dBu)
Line: 1,55V (+ 6dBu)
55 Hz - 23 kHz (EQ Monitor)
47 Hz - 23 kHz (EQ Monitor)
134 dB
134 dB
40º x 60º
40º x 60º
Birch Plywood
Birch Plywood
Isoflex Black Paint
Isoflex Black Paint
LF: 1 x 12R4 / GM 12P4
LF: 1 x 15R4 / GM 15R4
HF: 1 x M-75 / GM M-75
HF: 1 x M-75 / GM M-75
ANALOG INPUT: Female XLR
ANALOG INPUT: Female XLR
LOOP THRU ANALOG: Male XLR
LOOP THRU ANALOG: Male XLR
AC INPUT: PowerCon NAC 3 FCA
AC INPUT: PowerCon NAC 3 FCA
AC LOOP THRU: PowerCon NAC 3 FCB AC LOOP THRU: PowerCon NAC 3 FCB
115 V, 50Hz/60 Hz
115 V, 50 Hz/60 Hz
230 V, 50 Hz/60 Hz
230 V, 50 Hz/60 Hz
1.7A
1.7A
85V @ 115V
85V @ 115V
170V @ 230V
170V @ 230V
32.4 x 64.8 x 42 cm
37.1 x 74.7 x 48 cm
(12.8 x 25.5 x 16.5 in)
(14.6 x 29.4 x 18.9 in)
23.5 Kg (51.7 lb)
27.3 Kg (60 lb)
TRD-2
TRD-2
TRD-6
TRD-6
D.A.S. Audio S.A. continuously strives to enhance its products through investigation and development. All
specificationsare subject to change without prior warning.
ACCESSORIES
Occasionally, you may need to use the road system in a more generic way, by incorporating a tripod
insert in one of its handles.
This can be combined with subwoofers such as the avant-118A, with the use of a TRD-6, or use on a
standard tripod as the TRD-2.
Follow the instructions in the Safety Precautions section to prevent system instabilityor overturning.
Do not hesitate to contact us if there are any
questions, and remember that DAS Audio, only
recommends these configurations by using
accessoriesTRD-2 and TRD-6.
road
road
TRD-6
avant-118A
TRD-2
12
Manual del Usuario/ road series / User’s Manual
APPENDIX: Line connections: unbalanced and balanced
There are two basic ways to transport an audio signal with microphone or line level:
Unbalanced line: Utilising a two conductor cable, it transports the signal as the voltage between them.
Electromagnetic interference can get added to the signal as undesired noise. Connectors that carry
unbalanced signals have two pins, such as RCA (Phono) and ¼” (6.35mm, often referred to as jack) mono. 3
pin connector such as XLR (Cannon) may also carry unbalanced signals if one of the pins is unused.
Balanced line: Utilising a three conductor cable, one of them acts as a shield against electromagnetic
noise and is the ground conductor. The other two have the same voltage with respect to the ground
conductor but with opposite signs. The noise that cannot be rejected by the shield affects both signal
conductors in the same way. At the device’s input the two signals get summed with opposite sign, so that
noise is cancelled out while the programme signal doubles in level. Most professional audio devices use
balanced inputs and outputs. Connectors that can carry balanced signal have three pins, such as XLR
(Cannon) and ¼” (6.35mm) stereo.
The graphs that follow show the recommended connection with different types of connectors to balanced
processor or amplifier inputs. The connectors on the left-hand side come from a signal source, and the ones
on the right hand side go to the inputs of the processor or amplifier. Note that on the unbalanced connectors
on the left-hand side, two terminals are joined inside the connector. If hum occurs with balanced to balanced
connections, try disconnecting the sleeve (ground) on the input connector. Note that the illustrations show
what should be connected to what, but that pin locations on an actual XLR connector are different. Also, pin
2 hot is assumed on XLR connectors.
Manual del Usuario/ road series / User’s Manual
13
UM_ROAD_01_EN
www.dasaudio.com
D.A.S. AUDIO, S.A.
C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. 96 134 0525
Tel. Intl. +34 96 134 0860
Fax 96 134 0607
Fax Intl. +34 96 134 0607
D.A.S. AUDIO OF AMERICA, INC.
Sunset Palmetto Park
6816 NW 77th Court.
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1-888DAS4USA
Tel. +1 305 436 0521
Fax +1 305 436 0528
D.A.S. AUDIO ASIA PTE. LTD.
25 Kaki Bukit Crescent #01-00/02-00
Kaki Bukit Techpark 1
Singapore 416256
Tel. +65 6742 0151
Fax +65 6742 0157