Specification
Contents
Model
Before using
Parts name........................................ 1
Cautions............................................2
Installation and adjustment................. 4
How to use drainpipe.......................... 5
Water inlet installation........................ 6
Operation
Preparation before operation .............. 8
Load Laundries................................. 9
Use of detergent................................. 9
Program operation............................ 10
control panel instructions................10
operation steps............................. 12
Maintenance.................................... 13
Trouble shooting................................. 14
DWF-7288JD
Rated voltage and frequency
220V-240V~ 50Hz
Rated capacity of wash and spin
7.0kg (dry laundries weight)
Water level/water volume about
10/48L 9/45L 8/42L 7/38.5L
6/35L 5/32L 4/28.5L 3/25L
2/22L 1/19L
Inlet pressure
0.03MPa~0.85MPa
Rated input power
Wash 325W spin 250W
Weight
About 26.5kg
Dimensions
W523mm D523mm H875mm
Other functions................................. 16
Specification.................................... 17
17
Other functions
Parts name
1. Give an alarm
Top lid
Display
Explanation
E0
The top lid is opened
when preset is started
Feed valve
Settlement
Close the top lid and clear upthe alarm
Open top lid, according to before
troubleshooting and settlement to
settle it ,then close the top lidand
clear up the alarm.
E2
After draining 5 minutes,
it still does not reach to
water level
The top lid is open when
spinning
E3
Spin does not balance
E4
After inlet 20 minutes still
not reach to setting water
level
E5
The top lid is opened
after setting child-lock
Open top lid, according to before
troubleshooting and settlement to settle
it. Then close the tip lidand clear up the
alarm
Close the top lid and clear upthe
alarm
F1
Water level sensor is
wrong
Cut the power supply and call the
technicians
E1
Before using
Top frame
Detergent box
Lint filter
Close the top lid and clear upthe alarm
Control panel
Open the top lid ,make the laundries
place equally, then close it andclear
up the alarm
Inner tub
2. Imbalance adjustment
During spinning, if the laundries are not placed equally in the tub, it would cause
violent vibration. This machine has imbalance adjustment function, and the
vibration testing system will supervise the running. Once vibration is beyond certain
level, the adjustment system will start automatically to adjust the imbalance.
Back cover
Big pulsator
Body
Base
Power cord
Adjustable foot
Fixing foot(3pcs)
Accessories
The end connecting to
the appliance
Connector for
water inlet hose
and tap
3. Power supply is cut offautomatically
1) Press the power supply button and does not start the program in 10 minutes,
the power supply will be cut off automatically.
2) After the washing is finished, buzzer will remind, the power supply
can be cut off automatically.
The end connecting to
water inlet hose connector
4. Child lock function
1)if set child lock function, all the buttons will be locked including POWER. If the top lid
is opened during the washing machine working, the washing will be stopped and give an
alarm. But if you can close the top lid in 5 seconds, the washing machine will stop alarm
and continue working. If can not close the top lid in 5 seconds, the washing machine will
begin draining if there is water in the inner tub ,even closing the top lid is not valid. During
the draining, alarm will be given every 10 seconds , when the water in the inner tub is about
5cm higher, alarm will be given every 10 minutes (alarm is always given) . When the draining
is finished, the washing machine will be in the state of waiting, if close the top lid, the washing
machine is unlocked and start working as previous setting.
2) Once child lock is set, if open top lid over 5 seconds during washing or rinse(there is water
in the inner tub), washing machine will drain and give an alram. If you unlock the function during
draining, the washing machine will add water to setting water level and continue working.
Water inlet hose (1pc)
water inlet hose connector(1pc)
Bottom cover
(1pc)
Symbol definition
Warning symbols
Pay special attention to the warning symbols. There may be
serous risks to personal body safety or damages to the washing
machine if not follow.
5.Water Recycle Function
Set Water Recycle function, the machine will not drain and spin after the last rinse, the digital
timer display EE code, Spin indicator light flashing and alarm, the machine stop
working ( if no operation, buzzer alarm every 10 minutes,and power cut off after one hour),
press Start/Pause button, the digital timer displays the remaining time, enter the process
of drain, spin again, the water in the stainless steel inner tub can be reused.
16
Forbidden symbols
Please stop doing the contents with this symbol, otherwise
it will damage the appliance or injure your personal body.
1
Before
Before using
using
Cautions
Please insert the plug into the power socket with rated voltage
240V A/C.
Settlement
Always unplug the appliance and turn off the water when
the power is cut, moving or cleaning the washing machine,
or it is not in use. Do not insert or pull off the plug with wet hand.
Settlement
Insert the plug tightly
Check the socket or change to another socket
Press power switch
Check power supply
Do not make the electric cable bended, stretched, twisted, strapped or changed, pressed or nipped. If the electric cable or plug is
damaged or the socket becomes loose, they must be repaired or changed by our appointed repair stations or the professionals of
our post-sale service department to avoid danger. The pin of the plug must remain clean. Please clean it carefully with dry cloth if
it is dirty.
Install the inlet hose again
Tighten the connector of the machine
Put down the drainpipe
Straighten or clean the drainpipe
Don t install the washing machine in bathroom or damp
places,. Do not wash the machine with water, do not put
wet clothes on the control panel film.
Do not use water hotter than 50
C.
Restart when water supply is resumed
Open the tap
Clean the filter according to before clean inlet gate
The machine is adjusting automatically
If the machine is situated on a carpeted floor, please adjust
the feet in order to allow air to circulate freely.
Do not wash raincoat, bike cover, feather dress and such
waterproof laundries, which will make the washing machine
abnormal vibrations during spinning.
Close the top lid
Close the top lid
Ventilation holes
at the bottom
Soft item
Normal
Normal
Do not share the same socket with other electric appliances.
Do not use the damaged plug or loose socket.
Notes
2
If there is still a fault after the above checks, please pull out the plug and
contact the seller right away. It is dangerous to repair this product by yourself.
15
Troubleshooting
Cautions
Before contacting the technicians, please make the following checks:
Inlet hose leaks
Do not put hands into the working machine.
It is dangerous even if the speed is very slow.
Take special care of the children, and forbid
them to climb on the washing machine.
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Do not overload the appliance or put any hot
goods(such as the kettle with hot water)on the
washing machine.
Garments which have been in contact with
volatile petroleum products should not be
machine washed.
Possible reason
Phenomena
Control panel has no any display
Before using
Plug is not inserted tightly
No electricity in the socket
Power switch is not turned on
Power supply is cut off
Inlet hose connector(connecting with the tap)is not fixed tightly
Inlet hose and washing machine connector is loose
Petroleum
It does not drain
It does not inlet
Spin stops and begins to inlet
during spin program
Press the program button to
select SPIN, but It does not spin
The spin is intermittent when spin
Thinner
Drainpipe is not put down
Drainpipe is bended or get blocked
No water supply
Tap is not open
Inlet hose gets blocked
Laundries is too much or too little or the
Machine is not place stably
Do not close the top lid when drain is finished
Open up the top lid when start drain
Benzene
This appliance is not intended for use by persons(including children)
with reduced physical,sensory or mental capabilities,or lack of
experience and knowledge,unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
Keep the appliance away from direct
sunlight and heat sources like the heater.
Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp material
can cause extensive damage and must not be
placed into to the machine.
To prevent the lint from blocking cascade outlet
during washing, please keep the lint filter in good
condition, install it to proper position and clean it
in time.
Balance the laundries to reach to the best spin effect
starts
First time to use, some water flows
The remaining water when the factory make test
from the drainpipe
Dismantle
14
Before washing, please ensure the tap is open
and the inlet hose is installed properly.
It is suggested to use low foam washing powder.
Fit on
3
Installation and adjustment
Before using
Please install and adjust the machine according to the requirements of the manual.
It is very important to your safety and correct operation.
Operation
Maintenance
Maintenance methods
After the end of the programme
Unpacking
External cleaning
The machine stops automatically ,and music
buzzer will remind you to take out the laundries
or start again.
Once you have finished using the machine,
you are advised to unplug it and turn off the
water taps to avoid unexpected leak or fire.
Unpack the carton and take out the bottom panel.
Open the top lid of washing machine and take out all of the accessories.
Remove all wrappers, including the polystyrene base.
You are advised to keep all the packaging for reuse in case the machine is to be
transported again.
Clean the exterior cabinet of the appliance with
soft cloth. Do not use cleanser, volatile chemical
materials to clean the machine, which will
damage plastic parts and the surface.
Clean inlet gate
Clean the lint filter
It is necessary to use lint filter during
washing.
After washing, please clean the lint
filter in time.
Clean the lint filter according to the
following steps:
1. Pull out the lint filter.
2. Turn the filter net outside and
wash it.
3. Recover the filter net and
remount it.
It is possible that the inlet filter net can be blocked
by the dust, please clean it according to the follow
steps:
1. Close the tap and turn on the power switch.
2. Start the washing machine for 5 seconds(make
the water in the inlet hose flows to the tub),and
cut off the powersupply.
3. Pull off the inlet hose, remove and clean the inlet
valve and the inlet net, and install again.
Groove
Positioning
The distance between the washing machine and the wall should be more than 50mm, and the
maximum allowed angle of the shank base of the machine is 1 .The slanting or rough ground may
cause operating stopped or unstable, please adjust it with the following methods:
1.Once you have using the machine, you are advised to turn off the water taps.(if necessary, pull out
the inlet hose)
2. Do not keep water in tub for a long time. When washing is finished , drain it right away.
3.Once you have finished using the machine, you are advised to unplug it.
4. Put the electric cable and the drain hose in order.
5. Wipe the water on the surface and in tub with soft cloth and keep the top lid opening for a while. It
helps to prevent mould and stagnant smells forming inside the appliance.
Make it horizontal
Use a tied thread with plumb to check
If the water in the inner tub has possibility to freeze,please do like below:
1. In winter, if remaining water freeze can cause the washing machine trouble,
please take off the water inlet hose and drain out the water in the hose and inner
tub .
2. If the water freeze, please don't operate the washing machine. Put 40 hot water
in the tub, the hot water should submerge the pulsator, after a few minutes, rotate
the pulsator by hand gently, then you can operate the washing machine.
if it is horizontal.
1
Adjust the adjustable foot
1
Lift up the adjustable foot gently, loose the adjustable nut
and twist the adjustable foot.
2
Adjustable
nut
Fasten the nut after adjustment.
Loosen
High
4
Fasten
Adjustable
foot
Low
13
Operation steps
Operation
How to use drainpipe
Before using
Operation steps
1.Put through the power, press POWER button, the machine is in the state of beginning of start:
a.if there is no water in in ner tub,the machine is under the status of FUZZY, the PROCESS is
" wash-rinse-spin", digital timer displays "--", water level is not setting, PROGRAM is "REGULAR",
(if press "PROGRAM" , the digital timer displays"01"). If press " START/PAUSE" directly(press
"PROGRAM" to choose "02" HEAVY),the machie is also under thestatus of FUZZY), the
machine will start FUZZY sense and detect the weight of laundry, set the water level automatically.
b.if there is water in inne r tub, the machine is under the status of non-fuzzy, process is "WASHRINSE-SPIN", digital timer displays program time, water level is "7" ( if press "WATER LEVEL",
the digital timer displays "7"), program is "REGULAR" (press " PROGRAM", the digital timer
displays "01").
2.At the beginning of start,the process of spin can be set solely if no any other settings.
3.At the beginning of start,set programs by pressing" PROGRAM" button,the digital timer displays
from"01" to "10",corresponds 10 programs (regular,heavy,soft,standard,wool,mini,babies suits
tub clean,air dry,water recycle). Set"water recycle"program ( corresponds"10") and start running,
the machine does not drain and spin after last rinse, the digital timer displayes "EE"and"Spin"in
dicator light flashing and alarm,the machine stop working, press"Start/Pause"button to reset
alarm, enter the process of drain,spin again, the water in the stainless steel inner ub can be reused.
4.Press Water Level button to set water level,the digital timer displays from"1"to "10",corre
sponding the water level 1-10. At this moment, Fuzzy Logic function lose of function,the water
level is set according to the weight of laundries.
5.At the beginning of start,if need Preset,press"PRESET/AIR DRY"button to select proper washing
time. The indicator light will flashing each time pressing, the displayed time is the time end of
program. If need to cancel preset, press "POWER"button,will be on standby mode.
6.At the beginning of start,if need AIR Dry program, press"PROGRAM"button and select"AIR Dry"
program (corresponds 09 ),press PRESET/AIR Dry button again to set proper air dry time.
7.Close the top lid, and press Start/Pause button,the machine will start working. During working
, pressing and holding Water Level button and PRESET/Air Dry button can start child-lock
function, the digital timer displays remaining time and CL alternately, press again to release
child-lock. After start child lock function,if open top lid,the machine will stop working and give an
alarm.
8.When the washing is finished, buzzer alarm, power supply cut off automatically.
Water drainage
The drain hose should drain smoothly
1.The height of the drain hose should be less
than 10cm, otherwise the drainage will not be
smooth and need a long time to drain, the machine
may stop during working.
2.Do not step on or press the drain hose.
4. Purchase a proper hose if you need additional
drain hose. Its diameter should not less than
30mm and length should not exceed 1.5m.
If the additional drain hose is too long,
cut some at A or B point.
3.Cut the drain hose if it is too long. Cut the front end of the
hose slantingly to make drainage smoothly..
A B
12
5
Water inlet installation
Operation
Before using
Tap selection
Digital timer displays program code
Before washing, the digital timer
shows prest time, unit is HOUR.
If select AIR DRY, the digital timer
displays air dry time, unit is MIN.
When washing, the digital timer shows
the rest time of washing, unit is MIN.
When trouble encountered, the digital time
shows trouble code.
At the beginning of start, if with FUZZY logic,
The digital timer shows -- .
Not suitable tap
Suitable tap
After select program, process and water level, press
this button to start.
Press this button to pause during working, press again
will rework .
>1
0m
m
To control the washing machine is in
working state or waiting state.
The front end should be longer than 10mm The tap exit end face
should be flat and smooth, if not file it to avoid leakage
Connect the inlet hose connector with the tap
1
Press the lower end of the lock lever and push down the slider, take off the inlet hose
connector from the inlet hose, see illustration 1.
2
Loosen the four bolts on the inlet hose connector till the tap can be accessed, then
set the inlet hose connector in the tap, see illustration 2.(if the tap caliber is too larger and
could not set the inlet hose end, unscrew the four bolts and take out the bushing, tap exit
end must flat, otherwise it will leak, see illustration 3)
Inlet hose connector
Bolt
Slider
Screwdriver
Lock lever
Bushing
Inlet hose
Illustration 1
Illustration 2
Illustration3
3
Fasten the four bolts in the inlet hose connector evenly, see illustration 4.
4
Twist the fastening nut as the illustration ,see illustration 5.
Remark before twisting the nut, the threading is about 4mm above the upper surface of the nut, after twisting,
the threading is less than 2mm above the upper surface of the nut, see illustration 6.
Before twisting,about 4mm
After twisting,less 2mm
Nut
Illustration 4
Illustration 5
6
Illustration 6
According to the laundries weight and the user's demand to set proper programs
At the beginning of start, press "PROGRAM " button to set, digitial timer displays from
"0 1" to "10" total 10 programs (regular,heavy,soft,standard,wool,mini,babies suits
tub clean,air dry,water recycle)
Once you set "WATER RECYCLE " program ( the digital timer displays "10") and start
working, after the last rinse, the machine will not drain and spin, digital timer and
" spin" indicator lights sparkling , the machine gives an alarm and stop working. The
user can press " START/PAUSE" to clear the alarm, and then enter the process of
drain, spin, the user can reuse the water.
At the beginning of start, press this button to select preset time from 2-24 hours.
If want to cancel preset time, press POWER to make the washing machine in waiting state.
If need to select wind dry, please press "PROGRAM" button to select air dry( the digital timer displays "09"),
then press this button to set air dry time.
At the beginning of start, there is FUZZY logic and water level is not set, the digital timer displays "--".Before press "
START/PAUSE",if program is regular or heavy (the digitial timer displays "01" or "02"),the FUZZY function is
available. If program is standard( digital timer displays "04"), the FUZZY logic funciton is not available, the water level
is "7". If there is no WASH process setting, there is no FUZZY function.
At the beginning of start, press " WATER LEVEL" to set water level, the digital timer displays from "1" to "10",it is
water level 1 to water level 10. At the status, there is FUZZY function, you can set the water level according to the
weight of laundries. 1-2 is less water level , 3-4 is low water level, 5-8 is middle water level, 9-10 is high water level
During wash (including rinse), if need to add water, press WATER LEVEL button to add water, un-press will stop
adding. Or PAUSE the washing machine and press WATER LEVEL to select higher water level, then press START/
PAUSE button, The washing machine Will add the water to setting level automatically and continue working. If your
resetting water level is lower than present water level, the lower water Level will valid in next water inlet.
Automatically add water: during SOAK, WASH and RINSE process, if the washing machine check the water level is
lower than setting water level, The washing machine will pause and add water to setting water level automatically.
11
Control panel instruction
Mode and meaning of the indicator light
on: indicate the selected mode
flashing: indicate the program is running
Press this button to select one cycle from wash-rinse-spin
spin
soak-wash-rinse -spin
wash
wash-risne
rinse-spin .
At the beginning of start, the process setting is wash-rinse-spin .
Water inlet installation
Before using
Connect the inlet hose with the washing machine
1. Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it is, contact the seller immediately.
2. Put the inlet hose nut on the inlet valve connector.
3. Fasten the inlet hose nut and swing it gently to make
sue if it is suitable.
Inlet hose nut
Inlet valve connector
Water absorption cushion
Cautions:W hen install the washing machine, please use the new hose assy along with the washing
machine, old hose assy can not reuse.
Connect the inlet hose connector with the inlet hose
1. Push down the slider, insert the inlet hose into the connector
2. Hang the lock lever to the inlet hose connector and release
the slider till a click sound is heard.
Lock lever
Child-Lock Function
During the machine working, press "WATER LEVEL" and "PRESET/AIRDRY" buttons to set "CHILD-LOCK",
the digital timer displays remaining time and "CL" alternately ,press "WATER LEVEL" and"PRESET/AIRDRY"
buttons again to cancel child-lock.
Once child-lock function is set, all the buttons will be locked including power switch. If open the top lid
during the machine working, the machine will stop working and give an alarm. If open the top lid but
close in 5 seconds, the machine will stop alarm and continue to work. If open the top lid and and do not
close in 5 seconds, the machine will start draining if there is water in the inner tub, and give an alarm,
the machine will drain out the water and in the state of waiting( during draining even close the top lid ,
the draining will not stop. If cancel the child-lock function, the draing will stop), the machine will give
an alarm every 10 minutes, and the power supply will be cut off after 1 hour.
After setting child-lock function, during WASH or RINSE process ,if open the top lid for 5 seconds ( there
is water in the inner tub), the machine will start draining and give an alarm, if cancel the child-lock
function during draining, the machine will inlet water to the setting water level and continue to work.
Inlet hose connector
Slider
Check the connection between inlet hose
connector and the tap
1. Swing the inlet hose gently to confirm if it is fastened.
2. After installation, open the tap and check if it leaks.
3. Do not bend the inlet hose with overstrain.
4. Before each usage, check the connection between
inlet hose connector and the tap, and the installation
of inlet hose. Make sure they are firmly fitted to prevent
dropping from improper installation position.
Dismantle the inlet hose
At the beginning of start state
Put through the power, press POWER button, the machine is in the state of beginning of start:
1.if there is no water in inner tub,the machine is under the status of FUZZY, the PROCESS is " wash-rinse-spin", digital
timer displays "--", water level is not setting, PROGRAM is "REGULAR", (if press "PROGRAM" , he digital timer displays
"01"). If press " START/PAUSE" directly(press "PROGRAM" to choose "02" HEAVY),the machie is also under the
status of FUZZY), the machine will start FUZZY sense and detect the weight of laundry, set the water level automatically.
2. If there is water in inner tub, the machine is under the status of non-fuzzy, process is "WASH-RINSE-SPIN", digital timer
displays program time, water level is "7" ( if press "WATER LEVEL", the digital timer displays "7"), program is "REGULAR"
(press " PROGRAM", the digital timer displays "01").
10
1. Close the tap.
2. Press the locking lever, push down the slider, and pull of the
inlet hose. If the machine is used frequently, the connector
of the inlet hose can be kept on the tap to prevent damaging
the fixing screw.
7
Lock lever
Slider
Preparation before
operation
Operation
Load laundries
Operation
The capacity of washing and spinning of the machine refer
to the largest weight of the standard laundries under dry
condition .Washing quantity shall be lower than the rated
capacity. The maximum capacity of this machine is 7.0kg.
Different thickness, size and type of the laundries will
influence the actual washing capacity. It is suitable that
the laundries can be turned round normally during washing.
Do not select high water level when laundries are less than
1.5kg to avoid water splashing.
Preparation before washing
1. Connect the inlet hose and open the tap.
2. This appliance must be earthed. Confirm
the socket is earthed reliably and insert the
power plug. The earth terminal should not
link to gas pipeline, tap pipeline etc.
3. Put down the drainpipe.
Warning: the temperature of the water should less than 50
Use of detergent
Before washing the laundries, please pay attention to the followings:
Make sure if there is Before washing, empty Knot the long band,
special requirements all pockets of small
fasten the buttons
objects which may
for the laundries
and close the zippers.
have been left inside
(coins,keys,screws etc.)
As these could damage
the drain pump.
Do not overload the Sort the laundry
according to the type
machine. Load the
of fabric, color-fastness
laundry loosely
and how dirty it is. Put
alternating large
items with small ones. thin laundries, woolens
and such prone to wear
and tear laundries into
washing bag.
A. Make sure the laundries are washable.
B. It is essential to wash new colored items separately when washing for the first time. White items
should not be washed with colored items.
C. Please immerge the non-absorbable laundries by hand.
D. Some stains such as fruit, wine, grass, rust etc. are difficult to remove and should be treated
before washing with specific products, which can be found in most household shops. In some
cases it may help to soak the stain before washing with a special pre-soak product or biological
Detergent box
Withdraw the dispenser box before adding detergent
Pour concentrated synthetic washing powder into
the box directly as shown in the left illustration.
The dosage of the washing powder, please refer to
below.
It is suggested to use low sud washing powder.
How to use the washing powder
How to use bleach
Fill water to the selected level,
dilute the bleach in the container,
and pour it slowly into the washing
tub.
Do not use bleach for colored or
figured laundries as they are prone
to lose colors.
Do not put bleach to laundries
directly.
Refer to the manual for the usage
and quantity of the bleach.
Please dissolve powder bleach
before use.
detergent.
Dissolve in the machine directly not suitable for
preset program
1. Low water level.
2. Add the washing powder, and run for 30 seconds
to dissolve it completely.
3. Put laundries in, select suitable water level.
The instant dissolving of the washing powder
1. Prepare warm water of 30 in a container.
2. Pour the powder while stirring to fully dissolve it.
The washing powder is more prone to pollute the
laundries than the detergent, therefore, please use
it with proper quantity.
Washing powder with poor quality or not used for a
long period may get blocked, please clean the
detergent box in time.
E. Overturn the nap fabric and long floss laundries before putting them into the machine.
F. Do not put the laundries polluted by chemicals into the machine directly.
G.Very small item(handkerchiefs, ribbons, socks etc) should be washed in a washing bag or a pillow case.
It is suggested to use low foam washing powder
For the quantity of the concentrated washing powder, please refer to its manual
Remarks
avoid splashing of water and waste of washing powder, water level should not be too
high if laundries are too small.
8
9
Download PDF
Similar pages
MLTU16FGAWB
MLTU14GGAWB
MLTU16GGAWB
TOP LOAD WASHERS IL A ET
MLTU14FGAWB
AEG L75670FL washing machine
Troubleshooting &
10311 tuv english