2017 Infiniti Q60 Coupe | Owner'

Printing: June 2016 (01) / OM17E0 CV37U0 / Printed in U.S.A.
2017 Infiniti Q60
For your safety, read carefully and keep in this vehicle.
2017 Infiniti Q60
Owner’s Manual and
Maintenance Information
Owner’s Manual Supplement
The information contained within this supplement updates the information in the
2017 INFINITI Q60 Owner’s Manual:
● Repairing a Flat information in the “In case of emergency” section of this
manual.
● Checking Tire Pressures and Tire Chains information in the “Do-it-yourself”
section of this manual.
● WHEELS AND TIRES information in the “Technical and consumers information” section of this manual.
Read carefully and keep in vehicle
Printing: July 2016 (01)
Publication No. SU17E0 CV37U0
REPAIRING FLAT TIRE (for models
with emergency tire puncture repair
kit)
WARNING
● After using Emergency Tire Sealant to
repair a minor tire puncture, do not
drive the vehicle at speeds faster than
50 MPH (80 km/h).
● Immediately after using the Emergency
Tire Sealant to repair a minor tire puncture, take your vehicle to inspect, and
repair or replace the tire. It is recommended you visit an INFINITI retailer for
this service. The Emergency Tire Sealant cannot permanently seal a punctured tire. Continuing operation of the
vehicle without a permanent tire repair
can lead to a crash.
● INFINITI recommends using only Genuine NISSAN Emergency Tire Sealant
provided with your vehicle. Other tire
sealants may damage the valve stem
seal which can cause the tire to lose air
pressure. It is recommended you visit
an INFINITI retailer as soon as possible
after using tire repair sealant.
This vehicle does not have a spare tire. The
emergency tire puncture repair kit (Emergency
Tire Sealant) is supplied with the vehicle instead
of a spare tire. It can be used to temporarily repair
minor tire punctures.
If you have a flat tire, follow the instructions below.
CAUTION
● To avoid the emergency tire puncture
repair kit being damaged during storage or use:
– Only use the emergency tire puncture
repair kit on your vehicle. Do not use
it on other vehicles.
– Only use the kit to inflate the tires of
your vehicle and to check the vehicle’s tire pressure.
– Only plug the compressor into a 12V
DC car power point.
– Keep the kit free of water and dirt.
– Do not disassemble or modify the kit.
– Do not drop the kit or allow hard
impacts to the kit.
● Do not use the emergency tire puncture
repair kit under the following conditions. It is recommended you visit an
INFINITI retailer or professional road
assistance.
– when the sealant has passed its expiration date (shown on the label attached to the bottle)
– when the cut or the puncture is approximately 0.25 in (6 mm) or longer
– when the tire sidewall is damaged
– when the vehicle has been driven
with extremely low tire pressure
– when the tire has come off the inside
or the outside of the wheel.
– when the tire wheel is damaged
– when two or more tires are flat
STOPPING THE VEHICLE
1. Safely move the vehicle off the road and
away from traffic.
2. Turn on the hazard warning flashers.
3. Park on a level surface and apply the parking
brake.
4. Move the shift lever to the P (Park) position.
5. Turn off the engine.
6. Raise the hood to warn other traffic and to
signal professional road assistance personnel that you need assistance.
7. Have all passengers get out of the vehicle
and stand in a safe place, away from traffic
and clear of the vehicle.
BEFORE USING EMERGENCY TIRE
PUNCTURE REPAIR KIT
● If any foreign object (for example, a screw or
nail) is embedded in the tire, do not remove
it.
WARNING
● Make sure the parking brake is securely
applied and the transmission is shifted
into P (Park).
● Check the expiration date of the sealant
(shown on the label attached to the bottle).
Never use a sealant whose expiration date
has passed.
● Never repair tires when the vehicle is on
a slope, ice or slippery areas. This is
hazardous.
REPAIRING TIRE
● Never repair tires if oncoming traffic is
close to your vehicle. Wait for professional road assistance.
JVM0722X
GETTING EMERGENCY TIRE
PUNCTURE REPAIR KIT
Take out the emergency tire puncture repair kit
1 to open
located in the trunk. Remove the clips 䊊
the trunk trim as illustrated.
The repair kit consists of the following items:
● Tire sealant bottle
● Air compressor
● Speed restriction sticker
WARNING
Observe the following precautions when
using the tire repair compound.
● Swallowing the compound is dangerous. Immediately drink as much water
as possible and seek prompt medical
assistance.
● Rinse well with lots of water if the compound comes into contact with skin or
eyes. If irritation persists, seek prompt
medical attention.
● Keep the repair compound out of the
reach of children.
NOTE:
Do not remove any nails or screws that
have penetrated the tire when performing
repairs.
JVE0014X
1. Take out the speed restriction sticker from
the air compressor*, then put it in a location
where the driver can see it while driving.
*: The compressor shape may differ depending
on the models.
CAUTION
Do not put the speed restriction label on
the steering wheel pad, the speedometer
or the warning light locations.
SCE0868
1 and the power plug 䊊
2 out
2. Take the hose 䊊
of the air compressor. Remove the cap of the
bottle holder from the air compressor.
SCE0869
3. Remove the cap from the tire sealant bottle,
and screw the bottle clockwise onto the
bottle holder. (Leave the bottle seal intact.
Screwing the bottle onto the bottle holder
will pierce the seal of the bottle.)
4. Remove the cap from the tire valve on the flat
tire.
SCE0870
A of the hose
5. Remove the protective cap 䊊
and screw the hose securely onto the tire
valve. Make sure that the pressure release
B is securely tightened. Make sure
valve 䊊
that the air compressor switch is in the OFF
(O) position, and then insert its power plug
into the power outlet in the vehicle.
SCE0871
6. Push the ignition switch to the “ACC” position. Then turn the compressor switch to the
ON (⫺) position and inflate the tire up to the
pressure that is specified on the tire and
loading information label affixed to the driver’s side pillar if possible, or to the minimum
of 26 psi (180 kPa). Turn the air compressor
off briefly in order to check the tire pressure
with the pressure gauge.
If the tire is inflated to higher than the specified
pressure, lower the tire pressure by releasing air
with the pressure release valve.
NOTE:
The compressor tire pressure gauge may
show a pressure reading of 87 psi (600 kPa)
for about 30 seconds while inflating the
tire. The pressure gauge is indicating the
pressure inside the sealant can. When the
sealant has been injected into the tire the
pressure gauge will drop and indicate actual tire pressure.
WARNING
● To avoid serious personal injury while
using the emergency tire puncture repair kit:
– Securely tighten the compressor
hose to the tire valve. Failure to do so
can cause the sealant to spray into
the air and get into your eyes or on
the skin.
● Do not stand directly beside the damaged tire while it is being inflated because of the risk of the rupture. If there
are any cracks or bumps, turn the compressor off immediately.
If the tire pressure does not increase to 26 psi
(180 kPa) within 10 minutes, the tire may be
seriously damaged and the tire cannot be repaired with this tire puncture repair kit. It is
recommended you visit an INFINITI retailer for
servicing.
7. When the tire pressure is at the specified
amount, turn the air compressor off. If the
pressure cannot be inflated to the specified
amount, the air compressor can be turned
off at the minimum of 26 psi (180 kPa).
Remove the power plug from the power
outlet and quickly remove the hose from the
tire valve. Attach the protective cap and
valve cap. Properly stow the emergency tire
puncture repair kit in the trunk.
CAUTION
To avoid serious personal injury when
stowing the emergency tire puncture repair kit:
● Keep the sealant bottle screwed into
the compressor. Failure to do so can
cause the sealant to spray into the air
and get into your eyes or on the skin.
8. Immediately drive the vehicle for 10 minutes
or 2 miles (3 km) at a speed of 50 MPH
(80 km/h) or less.
9. After driving, make sure that the air compressor switch is in the OFF (O) position,
then screw the hose securely onto the tire
valve. Check the tire pressure with the pressure gauge. The temporary repair is completed if the tire pressure does not drop.
Make sure the pressure is adjusted to the
pressure that is specified on the tire and
loading information label before driving.
10. If the tire pressure drops, repeat the steps
from 5 to 9. If the pressure drops again or
under 19 psi (130 kPa), the tire cannot be
repaired with this tire puncture repair
kit. It is recommended you visit an INFINITI
retailer for this servicing.
The sealant bottle and hose cannot be reused to repair another punctured tire. It is
recommended you visit an INFINITI retailer
to purchase replacements.
CHECKING TIRE PRESSURE
AFTER REPAIRING TIRE
5. Add air to the tire as needed. If too much air
is added, press the core of the valve stem
briefly with the tip of the gauge stem to
release pressure. Recheck the pressure and
add or release air as needed.
It is recommended you visit an INFINITI retailer for
tire repair/replacement as soon as possible.
WARNING
6. Install the valve stem cap.
● After using Emergency Tire Sealant to
repair a minor tire puncture, do not
drive the vehicle at speeds faster than
50 MPH (80 km/h).
● Immediately after using Emergency Tire
Sealant to repair a minor tire puncture,
take your vehicle to inspect, and repair
or replace the tire. It is recommended
you visit an INFINITI retailer for this
service. The Emergency Tire Sealant
cannot permanently seal a punctured
tire. Continuing operation of the vehicle
without a permanent tire repair can lead
to a crash.
● INFINITI recommends using only Genuine NISSAN Emergency Tire Sealant
provided with your vehicle. Other tire
sealants may damage the valve stem
seal which can cause the tire to lose air
pressure. It is recommended you visit
an INFINITI retailer as soon as possible
after using tire repair sealant.
7. Check the pressure of all other tires, including the spare.
SIZE
LDI0393
1. Remove the valve stem cap from the tire.
2. Press the pressure gauge squarely onto the
valve stem. Do not press too hard or force
the valve stem sideways, or air will escape. If
the hissing sound of air escaping from the
tire is heard while checking the pressure,
reposition the gauge to eliminate this leakage.
3. Remove the gauge.
4. Read the tire pressure on the gauge stem
and compare it to the specification shown
on the Tire and Loading Information label.
P255/
40RF19
96V
FRONT
245/
ORIGINAL 40RF19
TIRE
94W
P245/
40RF19
94V
COLD
TIRE INFLATION
PRESSURE
240 kPa,
35 PSI
240 kPa,
35 PSI
240 kPa,
35 PSI
TIRE CHAINS
SIZE
P255/
40RF19
96V
265/
35RF19
REAR
94W
ORIGINAL
245/
TIRE
40RF19
94W
P245/
40RF19
94V
SPARE
T145/
TIRE (if so 70R18
equipped) 107M
COLD
TIRE INFLATION
PRESSURE
240 kPa,
35 PSI
240 kPa,
35 PSI
240 kPa,
35 PSI
240 kPa,
35 PSI
420 kPa,
60 PSI
CAUTION
Tire chains/cables should not be installed
on P255/40RF19 and 265/35RF19 tires.
Doing so will cause damage to the vehicle.
If you plan to use tire chains/cables, you
should
install
245/40RF19
or
P245/40RF19 tires on your vehicle.
Use of tire chains may be prohibited according to
location. Check the local laws before installing
tire chains. When installing tire chains, make sure
they are the proper size for the tires on your
vehicle and are installed according to the chain
manufacturer’s suggestions. Use only SAE
class S chains. Class “S” chains are used on
vehicles with restricted tire to vehicle clearance.
Vehicles that can use Class “S” chains are designed to meet the SAE standard minimum clearances between the tire and the closest vehicle
suspension or body component required to accommodate the use of a winter traction device
(tire chains or cables). The minimum clearances
are determined using the factory equipped tire
size. Other types may damage your vehicle. Use
chain tensioners when recommended by the tire
chain manufacturer to ensure a tight fit. Loose
end links of the tire chain must be secured or
removed to prevent the possibility of whipping
action damage to the fenders or underbody. If
possible, avoid fully loading your vehicle when
using tire chains. In addition, drive at a reduced
speed. Otherwise, your vehicle may be damaged
and/or vehicle handling and performance may be
adversely affected.
Tire chains must be installed only on the
rear wheels and not on the front wheels.
Never install tire chains on a TEMPORARY USE
ONLY spare tire (if so equipped). Never install tire
chains on a punctured run-flat tire (if so
equipped), as this could damage your vehicle.
Do not use tire chains on dry roads. Driving with
tire chains in such conditions can cause damage
to the various mechanisms of the vehicle due to
some overstress.
WHEELS AND TIRES
Road wheel
Type
Conventional
Spare (if so equipped)
Size
Offset in (mm)
19 x 9J
1.57 (40)
19 x 9J
1.46 (37)
19 x 9.5J
1.73 (44)
18 x 4T
0 (0)
Size
Pressure PSI (kPa) [Cold]
P255/40RF19 96V
35 (240)
245/40RF19 94W
35 (240)
P245/40RF19 94V
35 (240)
Front 245/40RF19 94W
Rear 265/35RF19 94W
35 (240)
35 (240)
T145/70R18 107M
60 (420)
Tire
Type
Conventional
Spare (T-type) (if so equipped)
DIMENSIONS
in (mm)
Overall length
184.4 (4,685)
Overall width
72.8 (1,850)
Overall height
54.9 (1,395)
54.5 (1,385)*1
Front tread
61.2 (1,555)*2
61.4 (1,560)*3
Rear tread
62.2 (1,580)*4
62.4 (1,585)*5
62.6 (1,590)*3
62.0 (1,575)*6
Wheelbase
112.2 (2,850)
*1: Two-Wheel Drive (2WD) models with VR30DDTT engine
*2: 255/40RF19 tire models
*3: 245/40RF19 tire models
*4: 255/40RF19 tire models with 2.0L turbo gasoline engine
*5: 255/40RF19 tire models with VR30DDTT engine
*6: 265/35RF19 tire models
WHEN TRAVELING OR REGISTERING
IN ANOTHER COUNTRY
If you plan to travel in another country, you
should first find out if the fuel available is suitable
for your vehicle’s engine.
Using fuel with too low an octane rating may
cause engine damage. All gasoline vehicles must
be operated with unleaded gasoline. Therefore,
avoid taking your vehicle to areas where appropriate fuel is not available.
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify the
vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle emission control and safety standards vary according
to the country, state, province or district; therefore, vehicle specifications may differ.
When any vehicle is to be taken into another country, state, province or district and
registered, its modifications, transportation, and registration are the responsibility
of the user. INFINITI is not responsible for
any inconvenience that may result.
(3,1)
Foreword
CV37D1-8D14BA72-70E0-4F77-8469-7DEC8F6401D5
Your INFINITI represents a new way of
thinking about vehicle design. It integrates
advanced engineering and superior craftsmanship with a simple, refined aesthetic
sensitivity associated with traditional Japanese culture.
The result is a different notion of luxury
and beauty. The car itself is important, but
so is the sense of harmony that the vehicle
evokes in its driver, and the sense of
satisfaction you feel with the INFINITI —
from the way it looks and drives to the high
level of retailer service.
To ensure that you enjoy your INFINITI to
the fullest, we encourage you to read this
Owner’s Manual immediately. It explains
all of the features, controls and performance characteristics of your INFINITI; it
also provides important instructions and
safety information.
A separate Warranty Information Booklet
is included in your Owner’s literature
portfolio. Always carry it with you when
you take your vehicle to an INFINITI
retailer. The Warranty Information Booklet
contents provide complete information
about all warranties covering this vehicle,
the requirements to keep the warranties in
effect as well as the INFINITI Roadside
Condition:
Assistance program.
Additionally, a separate Customer Care
and Lemon Law Information Booklet will
explain how to resolve any concerns you
may have with your vehicle, as well as
clarify your rights under your state’s
lemon law.
In addition to factory installed options,
your vehicle may also be equipped with
additional accessories installed by INFINITI
or by your INFINITI retailer prior to delivery.
It is important that you familiarize yourself
with all disclosures, warnings, cautions
and instructions concerning proper use of
such accessories prior to operating the
vehicle and/or accessory. It is recommended you see an INFINITI retailer for
details concerning the particular accessories with which your vehicle is equipped.
WARNING
IMPORTANT SAFETY INFORMATION REMINDERS!
Follow these important driving rules to help
ensure a safe and comfortable trip for you
and your passengers!
.
NEVER drive under the influence of
alcohol or drugs.
.
ALWAYS observe posted speed limits
and never drive too fast for conditions.
.
ALWAYS give your full attention to
driving and avoid using vehicle features
or taking other actions that could
distract you.
.
ALWAYS use your seat belts and appropriate child restraint systems. Pre-teen
children should be seated in the rear
seat.
.
ALWAYS provide information about the
proper use of vehicle safety features to
all occupants of the vehicle.
.
ALWAYS review this Owner’s Manual for
important safety information.
READ FIRST
— THEN DRIVE SAFELY
CV37D1-AC330383-C773-4EB3-A52F-61102B1D37CD
Before driving your vehicle, read your
Owner’s Manual carefully. This will ensure
familiarity with controls and maintenance
requirements, assisting you in the safe
operation of your vehicle.
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(4,1)
MODIFICATION OF YOUR VEHICLE
WHEN READING
THE MANUAL
CV37D1-F1CA4D19-16D5-4A3C-AF71-1A2BB3AD052B
This vehicle should not be modified.
Modification could affect its performance,
safety or durability, and may even violate
governmental regulations. In addition,
damage or performance problems resulting from modification will not be covered
under the INFINITI warranties.
This manual includes information for all
features and equipment available on this
model. Features and equipment in your
vehicle may vary depending on model, trim
level, options selected, order, date of
production, region or availability. Therefore, you may find information about
features or equipment that are not included or installed on your vehicle.
WARNING
Installing an aftermarket On-Board Diagnostic (OBD) plug-in device that uses the port
during normal driving, for example remote
insurance company monitoring, remote vehicle diagnostics, telematics or engine
reprogramming, may cause interference or
damage to vehicle systems. We do not
recommend or endorse the use of any
aftermarket OBD plug-in devices, unless
specifically approved by INFINITI. The vehicle warranty may not cover damage caused
by any aftermarket plug-in device.
Condition:
All information, specifications and illustrations in this manual are those in effect at
the time of printing. INFINITI reserves the
right to change specifications, performance, design or component suppliers
without notice and without obligation.
From time to time, INFINITI may update or
revise this manual to provide owners with
the most accurate information currently
available. Please carefully read and retain
with this manual all revision updates sent
to you by INFINITI to ensure you have
access to accurate and up-to-date information regarding your vehicle. Current versions of vehicle Owner’s Manuals and any
updates can also be found in the owner
section of the INFINITI website at https://
owners.infinitiusa.com/owners/navigation/manualsandGuides. If you have ques-
[ Edit: 2016/ 4/ 27
tions concerning any information in your
Owner’s Manual, contact INFINITI Consumer Affairs. See the INFINITI CUSTOMER
CARE PROGRAM page in this Owner’s
Manual for contact information.
IMPORTANT INFORMATION ABOUT
THIS MANUAL
CV37D1-3956A13C-AC00-461F-A84F-941327A05472
You will see various symbols in this
manual. They are used in the following
ways:
WARNING
This is used to indicate the presence of a
hazard that could cause death or serious
personal injury. To avoid or reduce the risk,
the procedures must be followed precisely.
CAUTION
This is used to indicate the presence of a
hazard that could cause minor or moderate
personal injury or damage to your vehicle. To
avoid or reduce the risk, the procedures
must be followed carefully.
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(5,1)
those above call attention to an item in the
illustration.
CALIFORNIA PROPOSITION 65
WARNING CV37D1-22D8B75D-68F8-4799-AD77-37863EA09A12
WARNING
SIC0697
If you see the symbol above, it means “Do
not do this” or “Do not let this happen”.
NOS1274
Engine Exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of
California to cause cancer and birth defects
or other reproductive harm. In addition,
certain fluids contained in vehicles and
certain products of component wear contain
or emit chemicals known to the State of
California to cause cancer and birth defects
or other reproductive harm.
If you see a symbol similar to those above
in an illustration, it means the arrow points
to the front of the vehicle.
Some vehicle parts, such as lithium
batteries, may contain perchlorate material. The following advisory is provided:
“Perchlorate Material - special handling
may apply, See www.dtsc.ca.gov/
hazardouswaste/perchlorate.”
INFINITI-13P
© 2016 NISSAN MOTOR CO., LTD.
All rights reserved. No part of this Owner’s
Manual may be reproduced or stored in a
retrieval system, or transmitted in any
form, or by any means, electronic, mechanical, photocopying, recording or otherwise,
without the prior written permission of
Nissan Motor Co., Ltd.
NOS1275
Arrows in an illustration that are similar to
those above indicate movement or action.
NOS1276
Arrows in an illustration that are similar to
Condition:
CALIFORNIA PERCHLORATE ADVISORY
CV37D1-E6CD19EB-0ED1-45BF-BAC9-C1A7DD80922F
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(6,1)
INFINITI CUSTOMER
CARE PROGRAM
CV37D1-7B10D04C-1C52-4B76-882C-7B9F38514835
INFINITI CARES ...
Both INFINITI and your INFINITI retailer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your
INFINITI retailer are our primary concerns. Your INFINITI retailer is always available to assist you with all your automobile sales and service
needs.
However, if there is something that your
INFINITI retailer cannot assist you with or
you would like to provide INFINITI directly
with comments or questions, please contact our (INFINITI’s) Consumer Affairs Department using our toll-free number:
For U.S. customers
1-800-662-6200
For Canadian customers
1-800-361-4792
The Consumer Affairs Department will ask
for the following information:
. Your name, address, and telephone
number
. Vehicle identification number (on dash
panel)
. Date of purchase
. Current odometer reading
. Your INFINITI retailer’s name
. Your comments or questions
OR
Condition:
You can write to INFINITI with the information on the left at:
For U.S. customers
INFINITI Division
Nissan North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003
or via e-mail at:
nnaconsumeraffairs@nissan-usa.
com
For Canadian customers
INFINITI Division
Nissan Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario L4W 4Z5
or via e-mail at:
information.centre@nissancanada.
com
[ Edit: 2016/ 4/ 27
If you prefer, visit us at:
www.infinitiUSA.com (for U.S. customer) or
www.infiniti.ca (for Canadian customers)
We appreciate your interest in INFINITI and
thank you for buying a quality INFINITI
vehicle.
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(1,1)
Table of
Contents
Condition:
Illustrated table of contents
0
Safety — Seats, seat belts and supplemental restraint system
1
Instruments and controls
2
Pre-driving checks and adjustments
3
Monitor, climate, audio, phone and voice recognition systems
4
Starting and driving
5
In case of emergency
6
Appearance and care
7
Do-it-yourself
8
Maintenance and schedules
9
Technical and consumer information
10
Index
11
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(2,1)
(7,1)
0 Illustrated table of contents
Seats, seat belts and Supplemental Restraint
System (SRS) ......................................................
...
Exterior front ......................................................
...
Exterior rear ........................................................
...
Passenger compartment .....................................
...
Cockpit ...............................................................
...
Condition:
0-2
0-3
0-4
0-5
0-6
Instrument panel ................................................
...
0-8
Meters and gauges .............................................
...
0-9
Engine compartment ........................................
...
0-10
VR30DDTT engine ........................................
...
0-10
2.0L turbo gasoline engine .........................
...
0-11
Warning and indicator lights ............................
...
0-12
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(8,1)
SEATS, SEAT BELTS AND SUPPLEMENTAL
RESTRAINT SYSTEM (SRS)
7.
Occupant classification sensors
(weight sensors) (P.1-46)
8. Front seats (P.1-3)
9. Seat belts with pretensioners (P.1-56)
10. Rear seat walk-in mechanism (P.1-5)
11. Rear seats (P.1-6)
— Child restraints (P.1-21)
12. LATCH (Lower Anchors and Tethers for
CHildren) system (P.1-23)
CV37D1-73C2D8AF-1731-4D5A-B261-B273439C9CA3
JVC0918X
1.
2.
3.
4.
Supplemental front-impact air bags
(P.1-40)
Front seat-mounted side-impact supplemental air bags (P.1-40)
Seat belts (P.1-11)
Head restraints (P.1-8)
5.
6.
Roof-mounted curtain side-impact
and rollover supplemental air bags
(P.1-40)
Child restraint anchor points (for top
tether strap child restraint) (P.1-25,
P.1-32, P.1-36)
0-2 Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(9,1)
EXTERIOR FRONT
6.
CV37D1-B377F75D-ECCA-4C6D-BBFA-4192086CFBFE
JVC0939X
1.
2.
Hood (P.3-23)
Windshield wiper and washer
— Switch operation (P.2-37)
— Window washer fluid (P.8-16)
3.
4.
5.
Headlights and turn signal lights
(P.2-40)
— Adaptive Front lighting System
(AFS) (if so equipped) (P.2-45)
Moonroof (if so equipped) (P.2-58)
Power windows (P.2-55)
Outside mirrors (P.3-31)
— Side turn signal lights (P.2-46)
— Side view camera* (if so equipped)
7. Front view camera* (if so equipped)
8. Sonar sensors (if so equipped)
— Around View Monitor* (if so
equipped)
9. Fog lights (P.2-47)
10. Tires
— Wheels and tires (P.8-33, P.10-11)
— Flat tire (P.6-3)
— Tire Pressure Monitoring System
(TPMS) (P.2-14, P.5-5)
11. Doors
— Keys (P.3-2)
— Door locks (P.3-4)
— Intelligent Key system (P.3-6)
— Remote keyless entry system
(P.3-16)
— Remote engine start (if so
equipped) (P.3-20)
— Courtesy light (P.2-62)
*: Refer to the Infiniti InTouch Owner’s
Manual.
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
0-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(10,1)
EXTERIOR REAR
5.
CV37D1-57AE6D4B-2D09-4713-AAB4-0355A17333C1
6.
7.
8.
*:
Sonar sensors (if so equipped)
— Around View Monitor* (if so
equipped)
— Back-up Collision Intervention
(BCI) system (if so equipped) (P.5-63)
Rear view camera*
Rear combination light (P.8-30)
Fuel-filler door (P.3-26)
— Fuel information (P.10-4)
Refer to the Infiniti InTouch Owner’s
Manual.
JVC0940X
1.
0-4
Trunk lid (P.3-23)
— Intelligent Key system (P.3-6)
— Remote keyless entry system
(P.3-16)
— Auxiliary battery (for 2.0L turbo
gasoline engine models) (P.8-18)
2.
3.
4.
High-mounted stop light (P.8-30)
Satellite antenna (P.4-3)
Rear window defroster (P.2-40)/Antenna (P.4-3)
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(11,1)
PASSENGER COMPARTMENT
10. Inside mirror (P.3-30)
— HomeLink® universal transceiver
(if so equipped) (P.2-62)
— Compass (if so equipped) (P.2-9)
11. Rear cup holders (P.2-51)
12. Console box (P.2-53)
— Power outlet (P.2-50)
— Media hub*
13. Front cup holders (P.2-51)
*: Refer to the Infiniti InTouch Owner’s
Manual.
CV37D1-3AA37B5B-1B7B-4B54-962C-B1F504C85062
JVC0941X
1.
2.
3.
4.
Coat hooks (P.2-54)
Power window switch (P.2-55)
Outside mirror remote control switch
(P.3-31)
Automatic drive positioner switch (if
so equipped) (P.3-33)
5.
6.
7.
8.
9.
Sun visors (P.3-29)
Moonroof switch (if so equipped)
(P.2-58)
SOS call switch* (if so equipped)
Map light (P.2-60)
Sunglasses holder (P.2-52)
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
0-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(12,1)
COCKPIT
4.
CV37D1-6C0E2194-048C-4AAF-8C07-A2793D31FC40
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
JVC0942X
1.
2.
3.
0-6
Side ventilator (P.4-2)
Headlight, fog light and turn signal
switch (P.2-40)
Steering wheel
— Horn (P.2-47)
— Driver supplemental air bag
(P.1-40)
— Heated steering wheel (if so
equipped) (P.2-49)
— Power steering (P.5-130)
16.
Windshield wiper and washer switch
(P.2-37)
Hazard warning flasher switch (P.6-2)
Shift lever (P.5-16)
INFINITI controller*
Vehicle Dynamic Control (VDC) OFF
switch (P.2-47, P.5-136)
Idling Stop OFF switch (if so equipped)
(P.5-140)
Trunk lid release switch (P.3-24)
Instrument brightness control switch
(P.2-46)
TRIP/RESET switch for twin trip odometer (P.2-7)
Electric tilting/telescopic steering
wheel switch (if so equipped) (P.3-28)
Manual tilting/telescopic steering
wheel lever (if so equipped) (P.3-28)
Steering-wheel-mounted controls (left
side)
— Audio control steering switch*
— Hands-Free Phone System switch*
— Voice recognition system switch*
Steering-wheel-mounted controls
(right side)
— Trip computer switches (P.2-31)
— Cruise control switches (if so
equipped) (P.5-74)
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(13,1)
— Intelligent Cruise Control (ICC)
switches (if so equipped) (P.5-76)
— Dynamic driver assistance switch
(if so equipped) (P. 5-27, P.5-35,
P.5-50, P.5-96)
17. INFINITI Drive Mode Selector (P.5-23)
*: Refer to the Infiniti InTouch Owner’s
Manual.
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
0-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(14,1)
INSTRUMENT PANEL
8.
CV37D1-0F64CFC5-D687-4457-83C2-8E0FE16A0B7B
9.
10.
11.
12.
13.
14.
15.
16.
17.
*:
Rear window and outside mirror
defroster switch (P.2-40)
Front passenger supplemental air bag
(P.1-40)
Hood release handle (P.3-23)
Fuse box cover (P.8-25)
Parking brake (P.5-22)
Storage box (P.2-54) and power outlet
(P.2-50)
Seat heater switch (if so equipped)
(P.2-48)
Audio system*
Trunk release power cancel switch
(P.3-25)
Glove box (P.2-53)
Refer to the Infiniti InTouch Owner’s
Manual.
JVC0969X
1.
2.
3.
4.
5.
0-8
Paddle shifter (if so equipped) (P.5-18)
Meters and gauges (P.2-6)
— Clock (P.2-34)
Push-button ignition switch (P.5-12)
Center ventilator (P.4-2)
Automatic climate control system*
6.
7.
Upper touch screen display* (upper
display) and Navigation system* (if so
equipped)
Lower touch screen display* (lower
display)
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(15,1)
METERS AND GAUGES
CV37D1-6D97ACA8-4DE2-4073-AC01-3AC6DD69386F
JVC0428X
1.
2.
3.
4.
Tachometer (P.2-8)
Warning and indicator lights (P.2-12)
Speedometer (P.2-7)
Engine coolant temperature gauge
(P.2-8)
5.
6.
Vehicle information display (P.2-21)/
Odometer/twin trip odometer (P.2-7)
Fuel gauge (P.2-9)
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
0-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(16,1)
ENGINE COMPARTMENT
CV37D1-25E83879-DE0B-4395-B935-F7008F1C97DD
JVC0968X
VR30DDTT
ENGINE
CV37D1-10EDAA85-F264-4887-8D4D-3DC66ACDB80B
1.
2.
3.
4.
5.
Battery (P.8-17)
Engine oil dipstick (P.8-10)
Engine oil filler cap (P.8-11)
Brake fluid reservoir (P.8-15)
Fuse/fusible link holder (P.8-25)
6.
7.
8.
9.
10.
11.
Air cleaner (P.8-22)
Engine drive belt location (P.8-20)
Radiator filler cap (P.8-6)
Intercooler cooling reservoir (P.8-9)
Engine coolant reservoir (P.8-7)
Window washer fluid reservoir
(P.8-16)
0-10 Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(17,1)
*:
The auxiliary battery is located in the
trunk. (See “Auxiliary battery location
(for 2.0L turbo gasoline engine models)” (P.8-18).)
JVC0646X
2.0L TURBO
GASOLINE ENGINE
CV37D1-83983D0E-38BF-47BB-9454-101673ACE468
1.
2.
3.
4.
5.
Fuse and fusible link holder (P.8-25)
Main battery* (P.8-17)
Engine oil filler cap (P.8-11)
Brake fluid reservoir (P.8-15)
Engine coolant reservoir (P.8-8)
6.
7.
8.
9.
Fuse and fusible link holder (P.8-25)
Engine oil dipstick (P.8-11)
Engine drive belt location (P.8-20)
Power steering fluid reservoir (if so
equipped) (P.5-130)
10. Window washer fluid reservoir
(P.8-16)
Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
0-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(18,1)
WARNING AND INDICATOR LIGHTS
CV37D1-AE45F736-D98A-4CF8-9862-081B0785133E
Warning
light
Name
Page
Anti-lock Braking System (ABS)
warning light
2-12
Brake warning light
2-13
Charge warning light
2-13
Forward Emergency Braking
(FEB) system warning light (if so
equipped)
Indicator
light
Name
Page
ECO drive indicator light (if so
equipped)
2-18
Exterior light indicator
2-18
Front fog light indicator light
2-18
Front passenger air bag status
light
2-18
High beam assist indicator light
(if so equipped)
2-19
2-14
High beam indicator light
2-19
Low fuel warning light
2-14
Idling Stop System indicator
light (if so equipped)
2-19
Low tire pressure warning light
2-14
Malfunction Indicator Light
(MIL)
2-19
Master warning light
2-16
Security indicator light
2-20
Power steering warning light
2-16
Turn signal/hazard indicator
lights
2-20
Seat belt warning light
2-17
2-17
Vehicle Dynamic Control (VDC)
off indicator light
2-20
Supplemental air bag warning
light
Vehicle Dynamic Control (VDC)
warning light
2-18
0-12 Illustrated table of contents
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(19,1)
1 Safety — Seats, seat belts and supplemental
restraint system
Seats ..................................................................
...
1-2
Front seats .....................................................
...
1-3
Rear seats ......................................................
...
1-6
Head restraints/headrests ..................................
...
1-8
Adjustable head
restraint/headrest components .......................
...
1-9
Non-adjustable head
restraint/headrest components .......................
...
1-9
Remove ..........................................................
...
1-9
Install ...........................................................
...
1-10
Adjust ..........................................................
...
1-10
Seat belts .........................................................
...
1-11
Precautions on seat belt usage .....................
...
1-11
Pregnant women ..........................................
...
1-13
Injured persons ............................................
...
1-14
Pre-crash seat belts with comfort function
(front seats) (if so equipped) ........................
...
1-14
Three-point type seat belt .............................
...
1-14
Seat belt extenders ......................................
...
1-17
Seat belt maintenance ..................................
...
1-18
Child safety ......................................................
...
1-18
Infants ..........................................................
...
1-19
Small children ..............................................
...
1-19
Larger children .............................................
...
1-19
Condition:
Child restraints ................................................
...
Precautions on child restraints ....................
...
Lower Anchors and Tethers for CHildren
System (LATCH) ...........................................
...
Rear-facing child restraint installation
using LATCH ................................................
...
Rear-facing child restraint installation using
the seat belts .............................................
...
Forward-facing child restraint installation
using LATCH ................................................
...
Forward-facing child restraint installation
using the seat belts ....................................
...
Booster seats ..............................................
...
Supplemental restraint system .........................
...
Precautions on supplemental
restraint system ..........................................
...
INFINITI Advanced Air Bag System
(front seats) ................................................
...
Front seat-mounted side-impact
supplemental air bag and roof-mounted
curtain side-impact and rollover
supplemental air bag systems ....................
...
Seat belts with pretensioners (front seats) ....
...
Supplemental air bag warning labels ..........
...
Supplemental air bag warning light ............
...
Repair and replacement procedure ..............
...
[ Edit: 2016/ 4/ 27
1-21
1-21
1-23
1-25
1-27
1-29
1-32
1-37
1-40
1-40
1-46
1-55
1-56
1-57
1-58
1-58
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(20,1)
SEATS
CV37D1-F6C5647E-51C1-45DD-A527-B12A30FCBE2A
your vehicle. Additionally, the temperature inside a closed vehicle on a warm
day can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
.
The seatback should not be reclined
further than necessary for comfort. Seat
belts are most effective when the passenger sits well back and straight up in
the seat. If the seatback is reclined, the
risk of sliding under the lap belt and
being injured is increased.
SSS0133
upright in the seat with both feet on the
floor and adjust the seat belt properly.
See “Precautions on seat belt usage”
(P.1-11).
WARNING
.
.
Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous. The shoulder belt will not be against
your body. In an accident, you could be
thrown into it and receive neck or other
serious injuries. You could also slide
under the lap belt and receive serious
internal injuries.
For the most effective protection when
the vehicle is in motion, the seat should
be upright. Always sit well back and
.
Do not leave children unattended inside
the vehicle. They could unknowingly
activate switches or controls. Unattended children could become involved
in serious accidents.
.
To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assistance of others or pets unattended in
CAUTION
When adjusting the seat positions, be sure
not to contact any moving parts to avoid
possible injuries and/or damages.
1-2 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(21,1)
FRONT SEATS
CV37D1-B05814F9-B0D6-4237-8C0F-FFC8B717E1A4
Front power
seat adjustment
CV37D1-152CA959-546B-4E86-887B-45E9AF10E014
Operating tips:
CV37D1-1FA5934D-050B-4CFB-BCFE-3D663EAB6AFF
. The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds, then reactivate the switch.
. Do not operate the power seat switch
for a long period of time when the
engine is off. This will discharge the
battery.
See “Automatic drive positioner” (P.3-33)
for the seat position memory function.
SSS1051
Forward andCV37D1-955B4ED6-F06C-4C42-A93D-050910FABF52
backward:
1 forward or backward
Moving the switch *
will slide the seat forward or backward to
the desired position.
back can be reclined to allow occupants to
rest when the vehicle is parked.
Reclining: CV37D1-167BD54F-A6FE-4C9B-A894-BBB222609EA3
2 backward until
Move the recline switch *
the desired angle is obtained. To bring the
seatback forward again, move the switch
2 forward.
*
The reclining feature allows adjustment of
the seatback for occupants of different
sizes for added comfort and to help obtain
proper seat belt fit. (See “Precautions on
seat belt usage” (P.1-11).) Also, the seatSafety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(22,1)
SSS1052
Seat lifter: CV37D1-4F80E44B-861D-4A46-BB27-AA76D11A212A
Push the front or rear end of the switch up
or down to adjust the angle of the front
portion or height of the seat.
SSS0836
SSS1053
Type A (if so equipped)
Lumbar support
(for driver’s seat):
CV37D1-9DD26B63-92AA-42B3-9F39-22ACE6681CC5
The lumbar support feature provides lower
back support to the driver.
Type B (if so equipped)
Type B (if so equipped)
1 up or down to adjust the
Move the lever *
seatback lumbar area.
Type A (if so equipped)
Push the front or back end of the switch to
adjust the seatback lumbar area.
1-4
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(23,1)
JVR0186X
Side support
(if so equipped):
CV37D1-D644C00C-CE0A-49A8-95E6-C4BC114B2E86
The side support feature allows you to
adjust the torso supports. Push the switch
1 or outside *
2 to adjust the torso
inside *
area.
JVR0497X
Walk-in mechanism:
GUID-A9FD327A-25B5-449F-8932-FB6A6FF7588B
This feature makes it easier to get in and
out of the rear seat. Use the following
procedure when getting in and out of the
rear seat.
If the sun visor is used, close it to the
original position before operating the walkin feature.
1 to
1. Pull the seatback lever upward *
fold the front seatback down. Make
sure that the front seatback is completely folded down.
2. To slide the front seat forward, firmly
2 . The front
push the seatback switch *
seat will move forward.
3. Get in or out of the vehicle.
4. To return the front seat to its original
position, raise the seatback and push
2 again.
the seatback switch *
. To stop the seat sliding, push the
2 again or operate
seatback switch *
the seat sliding/lifter switches.
. The front passenger seat will stop
returning 6.5 in (165.8 mm) from its
front-most position to retain space for
the rear passenger.
. Depending on the seat position, the
head restraint may contact the roof
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(24,1)
headlining during the walk-in operation. To prevent possible interference,
lower the seat using the seat lifter
switch.
WARNING
When returning the seat to its original
position, confirm the seat and seatback are
locked properly.
CAUTION
.
Be careful not to pinch your hand or foot
or bump your head when operating the
walk-in seat.
.
While operating the walk-in seat, do not
operate the seatback reclining switch.
The reclining motor may be damaged.
.
Do not place any objects near the seatback of the front seats. They may be
pinched and damaged.
1-6
The automatic forwarding and reversing
will not work or stop under the following
conditions:
. When the vehicle speed is moving
(driver’s seat only).
. When the seat belt is fastened.
. When the shift lever is not in the P
(Park) position (driver’s seat only).
. When the door is closed (automatic
forwarding only).
. While the automatic drive positioner (if
so equipped) operates.
. When the automatic drive positioner
switches (if so equipped) are pushed.
. When the seatback switch is pushed.
. When the seat position is adjusted.
Note that the seat must be moved to the
front-most position by operating the walkin function after the battery is disconnected. Otherwise, the seat will not move
backward during the walk-in function.
REAR SEATS
CV37D1-9B16344B-E483-4476-A755-41DF52A9E8A3
Folding
CV37D1-75C690C4-37A8-4BAF-B83B-B8551E268086
WARNING
.
Never allow anyone to ride in the trunk or
on the rear seat when it is in the folddown position. Use of these areas by
passengers without proper restraints
could result in serious injury in an
accident or sudden stop.
.
Properly secure all cargo with ropes or
straps to help prevent it from sliding or
shifting. Do not place cargo higher than
the seatback. In a sudden stop or
collision, unsecured cargo could cause
personal injury.
.
When returning the seatback to the
upright position, be certain they are
completely secured in the latched position. If they are not completely secured,
passengers may be injured in an accident or sudden stop.
.
Closely supervise children when they are
around cars to prevent them from playing and becoming locked in the trunk
where they could be seriously injured.
Keep the car locked, with the rear
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(25,1)
To fold the CV37D1-FE5F9742-AA59-4849-9CDF-C274DA5DB201
seatback:
1. Open the trunk lid.
seatback and trunk lid securely latched
when not in use, and prevent children’s
access to car keys.
2. Pull the strap located on the left side of
the trunk. The rear seatback will be
unlatched.
3. Fold the rear seatback down.
To return the
seatback:
CV37D1-CD13E846-65AB-472C-9072-F649E20C254C
1. Fold up the rear seatback.
2. Securely lock the seatback in position.
JVR0498X
The rear seatback can be folded according
to the following procedure.
Before folding
the seatback:
CV37D1-72D710CB-38DF-4A5E-863F-6C44C9BDCE3C
Remove drink containers from the rear cup
holder.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(26,1)
HEAD RESTRAINTS/HEADRESTS
CV37D1-C09406C0-75CE-44FB-8B10-D63822921103
WARNING
Head restraint/headrest supplement the
other vehicle safety systems. They may
provide additional protection against injury
in certain rear end collisions. Adjustable
head restraint/headrest must be adjusted
properly, as specified in this section. Check
the adjustment after someone else uses the
seat. Do not attach anything to the head
restraint/headrest stalks or remove the
head restraint/headrest. Do not use the
seat if the head restraint/headrest has been
removed. If the head restraint/headrest was
removed, reinstall and properly adjust the
head restraint/headrest before an occupant
uses the seating position. Failure to follow
these instructions can reduce the effectiveness of the head restraint/headrest. This
may increase the risk of serious injury or
death in a collision.
JVR0388X
The illustration shows the seating positions equipped with head restraint/headrest.
Indicates the seating position is
equipped with a head restraint.
Indicates the seating position is
equipped with a headrest.
. Adjustable head restraints/headrests
have multiple notches along the stalk
to lock them in a desired adjustment
position.
. The non-adjustable head restraints/
headrests have a single locking notch
to secure them to the seat frame.
. Proper Adjustment:
— For the adjustable type, align the
head restraint/headrest so the center of your ear is approximately level
with the center of the head restraint/headrest.
— If your ear position is still higher
than the recommended alignment,
place the head restraint/headrest at
the highest position.
. If the head restraint/headrest has been
removed, ensure that it is reinstalled
and locked in place before riding in that
designated seating position.
+ Indicates the seating position is not
equipped with a head restraint or headrest.
. Your vehicle is equipped with a head
restraint/headrest that may be integrated, adjustable or non-adjustable.
1-8
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(27,1)
SSS0992
JVR0203X
ADJUSTABLE HEAD RESTRAINT/
HEADRESTCV37D1-2DB7EA18-FDA7-4CE0-BF47-11604401DC36
COMPONENTS
NON-ADJUSTABLE HEAD RESTRAINT/HEADREST
COMPONENTS
CV37D1-8394078C-6ED9-47D2-8228-1D7740C86338
1. Removable head restraint/headrest
1. Removable head restraint/headrest
2. Multiple notches
2. Single notch
3. Lock knob
3. Lock knob
4. Stalks
4. Stalks
SSS1037
REMOVE
CV37D1-896D6833-2150-4355-89CD-2C8904366A02
Use the following procedure to remove the
head restraint/headrest.
1. Pull the head restraint/headrest up to
the highest position.
2. Push and hold the lock knob.
3. Remove the head restraint/headrest
from the seat.
4. Store the head restraint/headrest properly in a secure place so it is not loose
in the vehicle.
5. Reinstall and properly adjust the head
restraint/headrest before an occupant
uses the seating position.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(28,1)
SSS1038
INSTALL
CV37D1-E4047B01-BDED-4C45-A533-A49F85962AC9
1. Align the head restraint/headrest
stalks with the holes in the seat. Make
sure that the head restraint/headrest is
facing the correct direction. The stalk
1 must be
with the adjustment notch *
installed in the hole with the lock knob
2 .
*
SSS1035
SSS0997
ADJUST
CV37D1-15FAC2F7-19E9-42D2-BBB8-27C642986FBC
Adjust the head restraint/headrest so the
center is level with the center of your ears.
If your ear position is still higher than the
recommended alignment, place the head
restraint/headrest at the highest position.
Raise
CV37D1-0C95E2F9-C4C5-4D07-96FF-362131454DE8
To raise the head restraint/headrest, pull it
up.
Make sure the head restraint/headrest is
positioned so the lock knob is engaged in
the notch before riding in that designated
seating position.
2. Push and hold the lock knob and push
the head restraint/headrest down.
3. Properly adjust the head restraint/
headrest before an occupant uses the
seating position.
1-10 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(29,1)
SEAT BELTS
CV37D1-29FE26F0-CB52-4F95-85F6-5CC6F3EA4754
PRECAUTIONS
ON SEAT BELT USAGE
CV37D1-0A678CD3-4A52-4D86-8AB5-75E62AB34DD6
If you are wearing your seat belt properly
adjusted, and you are sitting upright and
well back in your seat with both feet on the
floor, your chances of being injured or
killed in an accident and/or the severity of
injury may be greatly reduced. INFINITI
strongly encourages you and all of your
passengers to buckle up every time you
drive, even if your seating position includes a supplemental air bag.
SSS1036
Lower
CV37D1-149560A1-B31D-4173-A669-7DF7A8747368
Most U.S. states and Canadian provinces
or territories specify that seat belts be
worn at all times when a vehicle is being
driven.
To lower, push and hold the lock knob and
push the head restraint/headrest down.
Make sure the head restraint/headrest is
positioned so the lock knob is engaged in
the notch before riding in that designated
seating position.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(30,1)
SSS0136A
SSS0016
SSS0134A
SSS0014
1-12 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(31,1)
.
Do not wear the seat belt inside out or
twisted. Doing so may reduce its effectiveness.
.
Do not allow more than one person to
use the same seat belt.
.
Never carry more people in the vehicle
than there are seat belts.
The seat belt should be properly adjusted to a snug fit. Failure to do so may
reduce the effectiveness of the entire
restraint system and increase the chance
or severity of injury in an accident.
Serious injury or death can occur if the
seat belt is not worn properly.
.
If the seat belt warning light glows
continuously while the ignition is turned
ON with all doors closed and all seat
belts fastened, it may indicate a malfunction in the system. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
.
Always route the shoulder belt over your
shoulder and across your chest. Never
run the belt behind your back, under
your arm or across your neck. The belt
should be away from your face and neck,
but not falling off your shoulder.
.
.
Position the lap belt as low and snug as
possible AROUND THE HIPS, NOT THE
WAIST. A lap belt worn too high could
increase the risk of internal injuries in an
accident.
WARNING
.
.
.
Every person who drives or rides in this
vehicle should use a seat belt at all
times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint.
Be sure the seat belt tongue is securely
fastened to the proper buckle.
.
No changes should be made to the seat
belt system. For example, do not modify
the seat belt, add material or install
devices that may change the seat belt
routing or tension. Doing so may affect
the operation of the seat belt system.
Modifying or tampering with the seat
belt system may result in serious personal injury.
Once a seat belt pretensioner has
activated, it cannot be reused and must
be replaced together with the retractor.
It is recommended you visit an INFINITI
retailer for this service.
.
All seat belt assemblies, including retractors and attaching hardware, should
be inspected after any collision. It is
recommended you visit an INFINITI retailer for this service. INFINITI recommends that all seat belt assemblies in
use during a collision be replaced unless
the collision was minor and the belts
show no damage and continue to operate properly. Seat belt assemblies not in
use during a collision should also be
inspected and replaced if either damage
or improper operation is noted.
.
All child restraints and attaching hardware should be inspected after any
collision. Always follow the restraint
manufacturer’s inspection instructions
and replacement recommendations. The
child restraints should be replaced if
they are damaged.
PREGNANT
WOMEN
CV37D1-68785179-C63E-48C7-846C-4DEDBC5E5B77
INFINITI recommends that pregnant women
use seat belts. The seat belt should be
worn snug, and always position the lap
belt as low as possible around the hips,
not the waist, and place the shoulder belt
over your shoulder and across your chest.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(32,1)
Never run the lap/shoulder belt over your
abdominal area. Contact your doctor for
specific recommendations.
INJURED PERSONS
CV37D1-7CEE9D29-DBCF-47A1-AD75-CAF60886623F
INFINITI recommends that injured persons
use seat belts, depending on the injury.
Check with your doctor for specific recommendations.
PRE-CRASH SEAT BELTS WITH COMFORT FUNCTION (front seats) (if so
equipped)CV37D1-8017E748-E53E-4E9A-925C-A78E351F9CDC
The pre-crash seat belt tightens the seat
belt with a motor to help restrain front seat
occupants. This helps reduce the risk of
injury in a collision.
The motor retracts the seat belt under the
following emergency conditions:
. During emergency braking.
. During sudden steering maneuvers.
. Activation of the Forward Emergency
Braking (FEB) system. (See “Forward
Emergency Braking (FEB) system” (P.5107).)
The pre-crash seat belt will not be active
when:
. The seat belt is not fastened.
. The vehicle speed is under 10 MPH (15
km/h) during emergency braking.
. The vehicle speed is under 19 MPH (30
km/h) during sudden steering maneuvers.
The pre-crash seat belt will not be active
when the brake pedal is not depressed
except when sudden steering maneuvers
occur or the FEB system activates.
The motor also retracts the seat belt when
the seat belt is fastened or unfastened.
When the seat belt is fastened, the motor
tightens the seat belt for a snug fit. When
the seat belt is unfastened, the motor
retracts the seat belt. If the seat belt is not
fully retracted, the motor retracts the seat
belt when the door is opened.
minutes, the motor normally reactivates
and retracts the seat belt. If the seat belt
still cannot be retracted by the motor, the
pre-crash seat belt system has a malfunction. Have the system checked and repaired. It is recommended you visit an
INFINITI retailer for this service.
THREE-POINT
TYPE SEAT BELT
CV37D1-18E2371D-E3E1-4A90-845A-3B3AAE7D3142
WARNING
.
Every person who drives or rides in this
vehicle should use a seat belt at all
times.
.
Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous. The shoulder belt will not be against
your body. In an accident, you could be
thrown into it and receive neck or other
serious injuries. You could also slide
under the lap belt and receive serious
internal injuries.
.
For the most effective protection when
the vehicle is in motion, the seat should
be upright. Always sit well back and
upright in the seat with both feet on the
floor and adjust the seat belt properly.
Always wear your seat belt correctly and sit
upright and well back.
If the motor cannot retract the seat belt
when the seat belt is fastened or unfastened, it may indicate the pre-crash seat
belt system has a malfunction. It is
recommended you have an INFINITI retailer
check and repair the system.
When the seat belt is retracted repeatedly
in a short period of time, the motor may not
be able to retract the seat belt. After a few
1-14 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(33,1)
smoothly pull the belt out of the
retractor.
WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the ALR
mode activated, the child can be seriously
injured or killed if the seat belt retracts and
becomes tight. This can occur even if the
vehicle is parked. Unbuckle the seat belt to
release the child.
SSS0292
Fastening CV37D1-4BE7D8BF-2851-459F-8264-6FA0DD410C73
the seat belts
1. Adjust the seat. (See “Seats” (P.1-2).)
2. Slowly pull the seat belt out of the
retractor and insert the tongue into the
buckle until you hear and feel the latch
engage.
. The retractor is designed to lock
during a sudden stop or on impact. A
slow pulling motion permits the belt
to move, and allows you some freedom of movement in the seat.
. If the seat belt cannot be pulled from
its fully retracted position, firmly
pull the belt and release it. Then
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(34,1)
The ELR locks the seat belt when the
vehicle slows down rapidly or during
impacts.
The Automatic Locking Retractor (ALR)
mode (child restraint mode) locks the seat
belt for child restraint installation.
SSS0290
3. Position the lap belt portion low and
snug on the hips as shown.
4. Pull the shoulder belt portion toward
the retractor to take up extra slack. Be
sure the shoulder belt is routed over
your shoulder and across your chest.
When the ALR mode is activated the seat
belt cannot be extended again until the
seat belt tongue is detached from the
buckle and fully retracted. The seat belt
returns to the ELR mode after the seat belt
fully retracts. For additional information,
see “Child restraints” (P.1-21).
The ALR mode should be used only for
child restraint installation. During normal
seat belt use by an occupant, the ALR
mode should not be activated. If it is
activated, it may cause uncomfortable seat
belt tension.
The three-point type seat belts have two
modes of operation:
. Emergency Locking Retractor (ELR)
. Automatic Locking Retractor (ALR)
The Emergency Locking Retractor (ELR)
mode allows the seat belt to extend and
retract to allow the driver and passengers
some freedom of movement in the seat.
WARNING
When fastening the seat belts, be certain
that seatbacks are completely secured in
the latched position. If they are not completely secured, passengers may be injured
in an accident or sudden stop.
SSS0326
Unfastening
the seat belts
CV37D1-6490E030-A1F5-4AC0-937F-FB64F07A2249
To unfasten the seat belt, push the button
on the buckle. The seat belt automatically
retracts.
Checking CV37D1-99ACE93E-BEA0-4237-B86D-15B33277D9A9
seat belt operation
Seat belt retractors are designed to lock
seat belt movement by two separate
methods:
. When the belt is pulled quickly from the
retractor.
. When the vehicle slows down rapidly.
To increase your confidence in the seat
belts, check the operation as follows:
1-16 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(35,1)
SEAT BELTCV37D1-EA87CE63-37A2-4716-9559-F5AB89630915
EXTENDERS
. Grasp the shoulder belt and pull forward quickly. The retractor should lock
and restrict further belt movement.
If the retractor does not lock during this
check, get the system checked. It is
recommended you visit an INFINITI retailer
for this service, or to learn more about seat
belt operation.
SSS0588
If, because of body size or driving position,
it is not possible to properly fit the lapshoulder belt and fasten it, an extender
that is compatible with the installed seat
belts is available that can be purchased.
The extender adds approximately 8 in (200
mm) of length and may be used for either
the driver or front passenger seating
position. It is recommended you visit an
INFINITI retailer for assistance with purchasing an extender if an extender is
required.
Shoulder belt
arm (for front seats)
GUID-295CCBD8-D89B-42F3-BA65-59417E9A898E
Before fastening the seat belt, pull the
shoulder belt arm forward until it clicks at
the lock position. The arm can also be
folded down for easier access for rear seat
passengers.
Pulling the arm forward will allow an easy
access to the belt.
WARNING
.
It is recommended only INFINITI seat belt
extenders, made by the same company
which made the original equipment seat
belts, be used with the INFINITI seat
belts.
.
Adults and children who can use the
standard seat belt should not use an
extender. Such unnecessary use could
result in serious personal injury in the
event of an accident.
.
Never use seat belt extenders to install
child restraints. If the child restraint is
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(36,1)
CHILD SAFETY
CV37D1-4EE25869-D4A8-4688-93AE-F4B2B0465998
not secured properly, the child could be
seriously injured or killed in a collision
or a sudden stop.
SEAT BELTCV37D1-724E27C2-8A16-4DAB-AC4C-60727D8C9395
MAINTENANCE
. To clean the seat belt webbing, apply a
mild soap solution or any solution
recommended for cleaning upholstery
or carpets. Then, wipe with a cloth and
allow the seat belts to dry in the shade.
Do not allow the seat belts to retract
until they are completely dry.
. If dirt builds up in the shoulder belt
guide of the seat belt anchors, the seat
belts may retract slowly. Wipe the
shoulder belt guide with a clean, dry
cloth.
. Periodically check to see that the seat
belt and the metal components such as
buckles, tongues, retractors, flexible
wires and anchors work properly. If
loose parts, deterioration, cuts or other
damage on the webbing is found, the
entire seat belt assembly should be
replaced.
WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the ALR
mode activated, the child can be seriously
injured or killed if the seat belt retracts and
becomes tight. This can occur even if the
vehicle is parked. Unbuckle the seat belt to
release the child.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in
this manual, child safety information is
available from many other sources, including doctors, teachers, government traffic
safety offices, and community organizations. Every child is different, so be sure to
learn the best way to transport your child.
There are three basic types of child
restraint systems:
. Rear-facing child restraint
. Forward-facing child restraint
. Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year
and less than 20 lbs (9 kg) should be
placed in rear-facing child restraints. Forward-facing child restraints are available
for children who outgrow rear-facing child
restraints and are at least 1 year old.
Booster seats are used to help position a
vehicle lap/shoulder belt on a child who
can no longer use a forward-facing child
restraint.
WARNING
Infants and children need special protection.
The vehicle’s seat belts may not fit them
properly. The shoulder belt may come too
close to the face or neck. The lap belt may
not fit over their small hip bones. In an
accident, an improperly fitting seat belt
could cause serious or fatal injury. Always
use appropriate child restraints.
All U.S. states and Canadian provinces or
territories require the use of approved
child restraints for infants and small
children. See “Child restraints” (P.1-21).
1-18 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(37,1)
A child restraint may be secured in the
vehicle by using either the LATCH (Lower
Anchor and Tethers for CHildren) system or
with the vehicle seat belt. See “Child
restraints” (P.1-21) for more information.
INFINITI recommends that all pre-teens
and children be restrained in the rear seat.
Studies show that children are safer when
properly restrained in the rear seat than in
the front seat.
This is especially important because your
vehicle has a supplemental restraint system (Air bag system) for the front passenger. See “Supplemental restraint system”
(P.1-40).
INFANTS
CV37D1-0DC2B248-D00D-4159-9D0A-861233779965
Infants up to at least 1 year old should be
placed in a rear-facing child restraint.
INFINITI recommends that infants be
placed in child restraints that comply with
Federal Motor Vehicle Safety Standards or
Canadian Motor Vehicle Safety Standards.
You should choose a child restraint that fits
your vehicle and always follow the manufacturer’s instructions for installation and
use.
SMALL CHILDREN
CV37D1-C9C54803-16A9-4E13-B935-F06D6F606BF4
Children that are over 1 year old and weigh
at least 20 lbs (9 kg) should remain in a
rear-facing child restraint as long as
possible up to the height or weight limit
of the child restraint. Children who outgrow
the height or weight limit of the rear-facing
child restraint and are at least 1 year old
should be secured in a forward-facing child
restraint with a harness. Refer to the
manufacturer’s instructions for minimum
and maximum weight and height recommendations. INFINITI recommends that
small children be placed in child restraints
that comply with Federal Motor Vehicle
Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a
child restraint that fits your vehicle and
always follow the manufacturer’s instructions for installation and use.
LARGER CHILDREN
CV37D1-4359DFEB-B409-4DE8-BEF0-9BE3771E94B2
Children should remain in a forward-facing
child restraint with a harness until they
reach the maximum height or weight limit
allowed by the child restraint manufacturer.
Once a child outgrows the height or weight
limit of the harness-equipped forward-
facing child restraint, INFINITI recommends
that the child be placed in a commercially
available booster seat to obtain proper
seat belt fit. For a seat belt to fit properly,
the booster seat should raise the child so
that the shoulder belt is properly positioned across the chest and the top, middle
portion of the shoulder. The shoulder belt
should not cross the neck or face and
should not fall off the shoulder. The lap belt
should lie snugly across the lower hips or
upper thighs, not the abdomen.
A booster seat can only be used in seating
positions that have a three-point type seat
belt. The booster seat should fit the vehicle
seat and have a label certifying that it
complies with Federal Motor Vehicle Safety
Standards or Canadian Motor Vehicle
Safety Standards.
A booster seat should be used until the
child can pass the seat belt fit test below:
. Are the child’s back and hips against
the vehicle seatback?
. Is the child able to sit without slouching?
. Do the child’s knees bend easily over
the front edge of the seat with feet flat
on the floor?
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(38,1)
. Can the child safely wear the seat belt
(lap belt low and snug across the hips
and shoulder belt across mid-chest and
shoulder)?
. Is the child able to use the properly
adjusted head restraint/headrest?
. Will the child be able to stay in position
for the entire ride?
WARNING
Never let a child stand or kneel on any seat
and do not allow a child in the cargo area.
The child could be seriously injured or killed
in a sudden stop or collision.
JVR0473X
If you answered no to any of these
questions, the child should remain in a
booster seat using a three-point type seat
belt.
NOTE:
Laws in some communities may follow
different guidelines. Check local and state
regulations to confirm your child is using
the correct restraint system before traveling.
1-20 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(39,1)
CHILD RESTRAINTS
CV37D1-1CF0D645-E792-4703-B560-9F7D2F020F51
PRECAUTIONS ON CHILD RESTRAINTSCV37D1-DF1C88B0-F8FE-4B02-B9A6-BB94E83BDF16
WARNING
.
SSS0099
Failure to follow the warnings and
instructions for proper use and installation of child restraints could result in
serious injury or death of a child or other
passengers in a sudden stop or collision:
— The child restraint must be used and
installed properly. Always follow all
of the child restraint manufacturer’s
instructions for installation and use.
— Infants and children should never be
held on anyone’s lap. Even the
strongest adult cannot resist the
forces of a collision.
— Do not put a seat belt around both a
child and another passenger.
SSS0100
— INFINITI recommends that all child
restraints be installed in the rear
seat. Studies show that children are
safer when properly restrained in the
rear seat than in the front seat. If you
must install a forward-facing child
restraint in the front seat, see “For-
ward-facing child restraint installation using the seat belts” (P.1-32).
— Even with the INFINITI Advanced Air
Bag System, never install a rearfacing child restraint in the front
seat. An inflating air bag could
seriously injure or kill a child. A
rear-facing child restraint must only
be used in the rear seat.
— Be sure to purchase a child restraint
that will fit the child and vehicle.
Some child restraints may not fit
properly in your vehicle.
— Child restraint anchor points are
designed to withstand loads from
child restraints that are properly
fitted.
— Never use the anchor points for
adult seat belts or harnesses.
— A child restraint with a top tether
strap should not be used in the front
passenger seat.
— Keep seatbacks as upright as possible after fitting the child restraint.
— Infants and children should always
be placed in an appropriate child
restraint while in the vehicle.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-21
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(40,1)
.
When the child restraint is not in use,
keep it secured with the LATCH system or
a seat belt. In a sudden stop or collision,
loose objects can injure occupants or
damage the vehicle.
CAUTION
A child restraint in a closed vehicle can
become very hot. Check the seating surface
and buckles before placing a child in the
child restraint.
This vehicle is equipped with a universal
child restraint anchor system, referred to
as the LATCH (Lower Anchors and Tethers
for CHildren) system. Some child restraints
include rigid or webbing-mounted attachments that can be connected to these
anchors.
For details, see “Lower Anchors and
Tethers for CHildren System (LATCH)” (P.123).
If you do not have a LATCH compatible child
restraint, the vehicle seat belts can be
used.
Several manufacturers offer child re-
straints for infants and small children of
various sizes. When selecting any child
restraint, keep the following points in
mind:
. Choose only a restraint with a label
certifying that it complies with Federal
Motor Vehicle Safety Standard 213 or
Canadian Motor Vehicle Safety Standard 213.
. Check the child restraint in your vehicle
to be sure it is compatible with the
vehicle’s seat and seat belt system.
. If the child restraint is compatible with
your vehicle, place your child in the
child restraint and check the various
adjustments to be sure the child
restraint is compatible with your child.
Choose a child restraint that is designed for your child’s height and
weight. Always follow all recommended
procedures.
. If the combined weight of the child and
child restraint is less than 65 lbs (29.5
kg), you may use either the LATCH
anchors or the seat belt to install the
child restraint (not both at the same
time).
. If the combined weight of the child and
child restraint is greater than 65 lbs
(29.5 kg), use the vehicle’s seat belt
(not the lower anchors) to install the
child restraint.
. Be sure to follow the child restraint
manufacturer’s instructions for installation.
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated. Canadian law requires the
top tether strap on forward-facing child
restraints be secured to the designated
anchor point on the vehicle.
1-22 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(41,1)
(not the lower anchors) to install the child
restraint. Be sure to follow the child
restraint manufacturer’s instructions for
installation.
LATCH lower
anchor
CV37D1-B84B41F2-A135-43AA-8D8C-8F7221F099C9
WARNING
JVR0499X
Lower Anchors and Tethers for
CHildren System
(LATCH)
CV37D1-C1C3934D-3833-4842-8D2B-271D02CB116E
Your vehicle is equipped with special
anchor points that are used with the LATCH
(Lower Anchors and Tethers for CHildren)
system compatible child restraints. This
system may also be referred to as the
ISOFIX or ISOFIX compatible system. With
this system, you do not have to use a
vehicle seat belt to secure the child
restraint unless the combined weight of
the child and child restraint exceeds 65 lbs
(29.5 kg). If the combined weight of the
child and child restraint is greater than 65
lbs (29.5 kg), use the vehicle’s seat belt
Failure to follow the warnings and instructions for proper use and installation of child
restraints could result in serious injury or
death of a child or other passengers in a
sudden stop or collision:
.
Attach LATCH system compatible child
restraints only at the locations shown in
the illustration.
.
Do not secure a child restraint in the rear
center position using the LATCH lower
anchors. The child restraint will not be
secured properly.
.
Inspect the lower anchors by inserting
your fingers into the lower anchor area.
Feel to make sure there are no obstructions over the anchors such as seat belt
webbing or seat cushion material. The
child restraint will not be secured
properly if the lower anchors are obstructed.
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
adult seat belts, or other items or equipment
to the vehicle. Doing so could damage the
child restraint anchorages. The child restraint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-23
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(42,1)
JVR0252X
LATCH lower
anchor location
CV37D1-2FAC51AF-2AEC-4C36-8B30-B7B0B690220C
The LATCH lower anchors are located,
under the covers labelled ISO FIX, at the
bottom of the rear seat cushions.
To access a LATCH lower anchor, insert your
finger into the cover and pull the cover off.
CAUTION
Store the loose LATCH lower anchor covers
to avoid losing them and where they will not
get damaged.
SSS0643
LATCH webbing-mounted attachment
Installing child restraint LATCH
lower anchor
attachments
CV37D1-D4B7854F-048F-46C5-A943-0021B55726A9
LATCH compatible child restraints include
two rigid or webbing-mounted attachments
that can be connected to two anchors
located at certain seating positions in your
vehicle. With this system, you do not have
to use a vehicle seat belt to secure the
child restraint. Check your child restraint
for a label stating that it is compatible with
LATCH. This information may also be in the
instructions provided by the child restraint
manufacturer.
SSS0644
LATCH rigid-mounted attachment
When installing a child restraint, carefully
read and follow the instructions in this
manual and those supplied with the child
restraint.
1-24 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(43,1)
adult seat belts, or other items or equipment
to the vehicle. Doing so could damage the
child restraint anchorages. The child restraint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.
REAR-FACING CHILD RESTRAINT INSTALLATION
USING LATCH
CV37D1-3EA280BC-E6EA-46BE-8A56-C11EBE28B4A0
SSS0790
Top tetherCV37D1-20CEF92A-45FA-4665-B712-6606D52BC917
anchor point locations
Anchor points are located on the rear
parcel shelf.
If you have any questions when installing
a top tether strap child restraint on the
rear seat, it is recommended you visit an
INFINITI retailer for this service.
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
Refer to all Warnings and Cautions in the
“Child safety” and “Child restraints” sections before installing a child restraint.
Do not use the lower anchors if the
combined weight of the child and the child
restraint exceeds 65 lbs (29.5 kg). If the
combined weight of the child and the child
restraint is greater than 65 lbs (29.5 kg),
use the vehicle’s seat belt (not the lower
anchors) to install the child restraint. Be
sure to follow the child restraint manufacturer’s instructions for installation.
SSS0648
Rear-facing web-mounted — step 2
2. Secure the child restraint anchor attachments to the LATCH lower anchors.
Check to make sure the LATCH attachment is properly attached to the lower
anchors.
Follow these steps to install a rear-facing
child restraint using the LATCH system:
1. Position the child restraint on the seat.
Always follow the child restraint manufacturer’s instructions.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-25
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(44,1)
SSS0649
Rear-facing rigid-mounted — step 2
SSS0639
Rear-facing — step 3
3. For child restraints that are equipped
with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your hand to compress the vehicle seat cushion and
seatback while tightening the webbing
of the anchor attachments.
SSS0650
Rear-facing — step 4
4. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the LATCH attachment path. The child restraint should
not move more than 1 inch (25 mm),
from side to side. Try to tug it forward
and check to see if the LATCH attachment holds the restraint in place. If the
restraint is not secure, tighten the
LATCH attachment as necessary, or put
the restraint in another seat and test it
again. You may need to try a different
child restraint or try installing by using
the vehicle seat belt (if applicable). Not
1-26 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(45,1)
all child restraints fit in all types of
vehicles.
5. Check to make sure the child restraint
is properly secured prior to each use. If
the child restraint is loose, repeat steps
1 through 4.
REAR-FACING CHILD RESTRAINT INSTALLATION
USING THE SEAT BELTS
CV37D1-55A7D551-E2FF-40B2-BEB9-31544F376FC0
restraint exceeds 65 lbs (29.5 kg). If the
combined weight of the child and the child
restraint is greater than 65 lbs (29.5 kg),
use the vehicle’s seat belt (not the lower
anchors) to install the child restraint. Be
sure to follow the child restraint manufacturer’s instructions for installation.
Follow these steps to install a rear-facing
child restraint using the vehicle seat belts
in the rear seats:
WARNING
The three-point seat belt with Automatic
Locking Retractor (ALR) must be used when
installing a child restraint. Failure to use the
ALR mode will result in the child restraint
not being properly secured. The restraint
could tip over or be loose and cause injury to
a child in a sudden stop or collision. Also, it
can change the operation of the front
passenger air bag. See “Front passenger
air bag and status light” (P.1-48).
SSS0100
Rear-facing — step 1
1. Child restraints for infants must be
used in the rear-facing direction and
therefore must not be used in the front
seat. Position the child restraint on the
seat. Always follow the restraint manufacturer’s instructions.
For additional information, refer to all
Warnings and Cautions in the “Child
safety” (P.1-18) and “Child restraints”
(P.1-21) before installing a child restraint.
Do not use the lower anchors if the
combined weight of the child and the child
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(46,1)
SSS0654
Rear-facing — step 2
2. Route the seat belt tongue through the
child restraint and insert it into the
buckle until you hear and feel the latch
engage. Be sure to follow the child
restraint manufacturer’s instructions
for belt routing.
SSS0655
Rear-facing — step 3
3. Pull the shoulder belt until the belt is
fully extended. At this time, the seat
belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the
Emergency Locking Retractor (ELR)
mode when the seat belt is fully
retracted.
SSS0656
Rear-facing — step 4
4. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack in
the belt.
1-28 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(47,1)
7. Check to make sure that the child
restraint is properly secured prior to
each use. If the seat belt is not locked,
repeat steps 1 through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode
(child restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT INSTALLATION USING
LATCH CV37D1-D9ED4467-51A0-45CD-B0F6-DFDE679BDEAC
SSS0657
Rear-facing — step 5
5. Remove any additional slack from the
seat belt; press downward and rearward firmly in the center of the child
restraint to compress the vehicle seat
cushion and seatback while pulling up
on the seat belt.
SSS0658
Rear-facing — step 6
6. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the seat belt path.
The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to
see if the belt holds the restraint in
place. If the restraint is not secure,
tighten the seat belt as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles.
Refer to all Warnings and Cautions in the
“Child safety” and “Child restraints” sections before installing a child restraint.
Do not use the lower anchors if the
combined weight of the child and the child
restraint exceeds 65 lbs (29.5 kg). If the
combined weight of the child and the child
restraint is greater than 65 lbs (29.5 kg),
use the vehicle’s seat belt (not the lower
anchors) to install the child restraint. Be
sure to follow the child restraint manufacturer’s instructions for installation.
Follow these steps to install a forwardfacing child restraint using the LATCH
system:
1. Position the child restraint on the seat.
Always follow the child restraint man-
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-29
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(48,1)
ufacturer’s instructions.
SSS0645
Forward-facing web-mounted — step 2
2. Secure the child restraint anchor attachments to the LATCH lower anchors.
Check to make sure the LATCH attachment is properly attached to the lower
anchors.
If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point. See “Installing top
tether strap” (P.1-32). Do not install
child restraints that require the use of a
top tether strap in seating positions
that do not have a top tether anchor.
SSS0646
Forward-facing rigid-mounted — step 2
3. The back of the child restraint should
be secured against the vehicle seatback.
If the seating position does not have an
adjustable head restraint and it is
interfering with the proper child restraint fit, try another seating position
or a different child restraint.
1-30 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(49,1)
7. Check to make sure the child restraint
is properly secured prior to each use. If
the child restraint is loose, repeat steps
1 through 6.
SSS0647
Forward-facing — step 4
4. For child restraints that are equipped
with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your knee to compress the vehicle seat cushion and
seatback while tightening the webbing
of the anchor attachments.
5. Tighten the tether strap according to
the manufacturer’s instructions to remove any slack.
SSS0638
Forward-facing — step 6
6. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the LATCH attachment path. The child restraint should
not move more than 1 inch (25 mm),
from side to side. Try to tug it forward
and check to see if the LATCH attachment holds the restraint in place. If the
restraint is not secure, tighten the
LATCH attachment as necessary, or put
the restraint in another seat and test it
again. You may need to try a different
child restraint. Not all child restraints fit
in all types of vehicles.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-31
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(50,1)
The child restraint top tether strap must be
used when installing the child restraint
with the LATCH lower anchor attachments.
First, secure the child restraint with the
LATCH lower anchors (rear outboard seating positions only).
1. Flip up the anchor cover from the
anchor point which is located directly
behind the child restraint.
2. Position the top tether strap over the
top of the seatback.
SSS0790
Installing CV37D1-7DD66191-C752-4AE4-930B-C21472A1E7E6
top tether strap
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
adult seat belts, or other items or equipment
to the vehicle. Doing so could damage the
child restraint anchorages. The child restraint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.
3. Secure the tether strap to the tether
anchor point on the rear parcel shelf.
4. Refer to the appropriate child restraint
installation procedure steps in this
section before tightening the tether
strap.
FORWARD-FACING CHILD RESTRAINT INSTALLATION USING THE
SEAT BELTS
CV37D1-4DB798E7-E9AF-4F3F-8757-7FA8B7D2601A
WARNING
The three-point seat belt with Automatic
Locking Retractor (ALR) must be used when
installing a child restraint. Failure to use the
ALR mode will result in the child restraint
not being properly secured. The restraint
could tip over or be loose and cause injury to
a child in a sudden stop or collision. Also, it
can change the operation of the front
passenger air bag. See “Front passenger
air bag and status light” (P.1-48).
If you have any questions when installing
a top tether strap, it is recommended you
visit an INFINITI retailer for this service.
1-32 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(51,1)
belt in the rear seats or in the front
passenger seat:
child restraint fit, try another seating
position or a different child restraint.
1. If you must install a child restraint in
the front seat, it should be placed in a
forward-facing direction only. Move the
seat to the rearmost position. Child
restraints for infants must be used in
the rear-facing direction and, therefore, must not be used in the front seat.
2. Position the child restraint on the seat.
Always follow the child restraint manufacturer’s instructions.
SSS0640
Forward-facing (front passenger seat) —
step 1
Refer to all Warnings and Cautions in the
“Child safety” and “Child restraints” sections before installing a child restraint.
Do not use the lower anchors if the
combined weight of the child and the child
restraint exceeds 65 lbs (29.5 kg). If the
combined weight of the child and the child
restraint is greater than 65 lbs (29.5 kg),
use the vehicle’s seat belt (not the lower
anchors) to install the child restraint. Be
sure to follow the child restraint manufacturer’s instructions for installation.
Follow these steps to install a forwardfacing child restraint using the vehicle seat
The back of the child restraint should
be secured against the vehicle seatback.
If necessary, adjust or remove the head
restraint or headrest to obtain the
correct child restraint fit. If the head
restraint or headrest is removed, store
it in a secure place. Be sure to reinstall
the head restraint or headrest when
the child restraint is removed. See
“Head restraints/headrests” (P.1-8) for
head restraint or headrest adjustment,
removal and installation information.
If the seating position does not have an
adjustable head restraint or headrest
and it is interfering with the proper
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-33
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(52,1)
SSS0360B
Forward-facing — step 3
3. Route the seat belt tongue through the
child restraint and insert it into the
buckle until you hear and feel the latch
engage. Be sure to follow the child
restraint manufacturer’s instructions
for belt routing.
If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point (rear seat installation only). See “Installing top tether
strap” (P.1-36). Do not install child
restraints that require the use of a top
tether strap in seating positions that do
not have a top tether anchor.
SSS0651
Forward-facing — step 4
4. Pull the shoulder belt until the belt is
fully extended. At this time, the seat
belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to Emergency
Locking Retractor (ELR) mode when the
seat belt is fully retracted.
SSS0652
Forward-facing — step 5
5. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack in
the belt.
1-34 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(53,1)
9. Check to make sure the child restraint
is properly secured prior to each use. If
the seat belt is not locked, repeat steps
2 through 8.
SSS0653
Forward-facing — step 6
6. Remove any additional slack from the
seat belt; press downward and rearward firmly in the center of the child
restraint with your knee to compress
the vehicle seat cushion and seatback
while pulling up on the seat belt.
7. Tighten the tether strap according to
the manufacturer’s instructions to remove any slack.
SSS0641
Forward-facing — step 8
8. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the seat belt path.
The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to
see if the belt holds the restraint in
place. If the restraint is not secure,
tighten the seat belt as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-35
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(54,1)
The child restraint top tether strap must be
used when installing the child restraint
with the seat belts.
First, secure the child restraint with the
seat belt.
1. Flip up the anchor cover from the
anchor point which is located directly
behind the child restraint.
2. Position the top tether strap over the
top of the seatback.
JVR0192X
Forward-facing — step 10
10. If the child restraint is installed in the
front passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
should illuminate. If this light is not
illuminated, see “Front passenger air
bag and status light” (P.1-48). Move the
child restraint to another seating position. Have the system checked. It is
recommended you visit an INFINITI
retailer for this service.
After the child restraint is removed and the
seat belt is fully retracted, the ALR mode
(child restraint mode) is canceled.
SSS0790
Installing CV37D1-C501F3B2-B525-4F0E-A619-D50D32F95904
top tether strap
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
adult seat belts, or other items or equipment
to the vehicle. Doing so could damage the
child restraint anchorages. The child restraint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.
3. Secure the tether strap to the tether
anchor point on the rear parcel shelf.
4. Refer to the appropriate child restraint
installation procedure steps in this
section before tightening the tether
strap.
If you have any questions when installing
a top tether strap, it is recommended you
visit an INFINITI retailer for this service.
1-36 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(55,1)
BOOSTER CV37D1-8603BE0C-5AB5-422E-8F8B-F15C086912E5
SEATS
Precautions
on booster seats
CV37D1-EEB07257-7590-4249-8F66-9FD497B4B441
WARNING
If a booster seat and seat belt are not used
properly, the risk of a child being injured or
killed in a sudden stop or collision greatly
increases:
.
Make sure the shoulder portion of the
belt is away from the child’s face and
neck and the lap portion of the belt does
not cross the stomach.
.
Make sure the shoulder belt is not
behind the child or under the child’s
arm.
.
A booster seat must only be installed in
a seating position that has a lap/
shoulder belt.
LRS0455
Booster seats of various sizes are offered
by several manufacturers. When selecting
any booster seat, keep the following points
in mind:
. Choose only a booster seat with a label
certifying that it complies with Federal
Motor Vehicle Safety Standard 213 or
Canadian Motor Vehicle Safety Standard 213.
. Check the booster seat in your vehicle
to be sure it is compatible with the
vehicle’s seat and seat belt system.
LRS0453
. Make sure the child’s head will be
properly supported by the booster seat
or vehicle seat. The seatback must be at
or above the center of the child’s ears.
For example, if a low back booster seat
1
is chosen, the vehicle seatback
*
must be at or above the center of the
child’s ears. If the seatback is lower
than the center of the child’s ears, a
2 should be
high back booster seat *
used.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-37
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(56,1)
Booster seat
installation
CV37D1-DDD94AC0-6287-4721-8872-2368FD1B503C
CAUTION
To avoid injury to child, do not use the lap/
shoulder belt Automatic Locking Retractor
(ALR) mode when using a booster seat with
the seat belts.
LRS0464
. If the booster seat is compatible with
your vehicle, place your child in the
booster seat and check the various
adjustments to be sure the booster seat
is compatible with your child. Always
follow all recommended procedures.
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated.
Refer to all Warnings and Cautions in the
“Child safety”, “Child restraints” and
“Booster seats” sections earlier in this
section before installing a child restraint.
Follow these steps to install a booster seat
in the rear seat or in the front passenger
seat:
SSS0640
1. If you must install a booster seat in the
front seat, move the seat to the rearmost position.
2. Position the booster seat on the seat.
Only place it in a forward-facing direction. Always follow the booster seat
manufacturer’s instructions.
The instructions in this section apply to
booster seat installation in the rear seats
or the front passenger seat.
1-38 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(57,1)
and it is interfering with the proper
booster seat fit, try another seating
position or a different booster seat.
4. Position the lap portion of the seat belt
low and snug on the child’s hips. Be
sure to follow the booster seat manufacturer’s instructions for adjusting the
seat belt routing.
LRS0454
Front passenger position
3. The booster seat should be positioned
on the vehicle seat so that it is stable.
If necessary, adjust or remove the head
restraint or headrest to obtain the
correct booster seat fit. If the head
restraint or headrest is removed, store
it in a secure place. Be sure to reinstall
the head restraint or headrest when
the booster seat is removed. See “Head
restraints/headrests” (P.1-8) for head
restraint or headrest adjustment, removal and installation information.
5. Pull the shoulder belt portion of the
seat belt toward the retractor to take up
extra slack. Be sure the shoulder belt is
positioned across the top, middle portion of the child’s shoulder. Be sure to
follow the booster seat manufacturer’s
instructions for adjusting the seat belt
routing.
6. Follow the warnings, cautions and
instructions for properly fastening a
seat belt shown in “Seat belts” (P.111).
JVR0192X
7. If the booster seat is installed in the
front passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
may
or may not illuminate depending on the
size of the child and the type of booster
seat used. See “Front passenger air
bag and status light” (P.1-48).
If the seating position does not have an
adjustable head restraint or headrest
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-39
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(58,1)
SUPPLEMENTAL RESTRAINT SYSTEM
CV37D1-FA8250CE-0174-4FD9-90BA-5B43C650911A
PRECAUTIONS ON SUPPLEMENTAL
RESTRAINT
SYSTEM
CV37D1-33B797EF-5B18-4EA6-A1F0-A150B541B8DC
This Supplemental Restraint System (SRS)
section contains important information
concerning the following systems:
. Driver and passenger front-impact supplemental air bags (INFINITI Advanced
Air Bag System)
. Front seat-mounted side-impact supplemental air bag
. Roof-mounted curtain side-impact and
rollover supplemental air bag
. Seat belt with pretensioner
Supplemental front-impact air bag system:
The INFINITI Advanced Air Bag System can
help cushion the impact force to the head
and chest of the driver and front passenger
in certain frontal collisions.
Front seat-mounted side-impact supplemental air bag system: This system can
help cushion the impact force to the chest
and pelvis area of the driver and front
passenger in certain side impact collisions.
The side air bag is designed to inflate on
the side where the vehicle is impacted.
Roof-mounted curtain side-impact and
rollover supplemental air bag system: This
system can help cushion the impact force
to the head of occupants in front and rear
outboard seating positions in certain side
impact or rollover collisions. In a side
impact, the curtain air bags are designed
to inflate on the side where the vehicle is
impacted. In a rollover, curtain air bags on
both sides are designed to inflate and
remain inflated for a short time.
After placing the ignition switch in the ON
position, the supplemental air bag warning light illuminates. The supplemental air
bag warning light will turn off after about 7
seconds if the systems are operational.
Curtain air bags are also designed to
inflate in certain types of rollover collisions
or near rollovers. As a result, certain
vehicle movements (for example, during
severe off-roading) may cause the curtain
air bags to inflate.
These supplemental restraint systems are
designed to supplement the crash protection provided by the driver and passenger
seat belts and are not a substitute for
them. Seat belts should always be correctly worn and the occupant seated a
suitable distance away from the steering
wheel, instrument panel and door finishers. (See “Seat belts” (P.1-11) for
instructions and precautions on seat belt
usage.)
The supplemental air bags operate only
when the ignition switch is in the ON
position.
1-40 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(59,1)
WARNING
.
The front air bags ordinarily will not
inflate in the event of a side impact, rear
impact, rollover, or lower severity frontal
collision. Always wear your seat belts to
help reduce the risk or severity of injury
in various kinds of accidents.
.
The front passenger air bag will not
inflate if the passenger air bag status
light is lit. See “Front passenger air bag
and status light” (P.1-48).
.
The seat belts and the front air bags are
most effective when you are sitting well
back and upright in the seat with both
feet on the floor. The front air bags
inflate with great force. Even with the
INFINITI Advanced Air Bag System, if you
are unrestrained, leaning forward, sitting sideways or out of position in any
way, you are at greater risk of injury or
death in a crash. You may also receive
serious or fatal injuries from the front air
bag if you are up against it when it
inflates. Always sit back against the
seatback and as far-away as practical
from the steering wheel or instrument
panel. Always use the seat belts.
SSS0131B
SSS0132B
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-41
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(60,1)
.
The driver and front passenger seat belt
buckles are equipped with sensors that
detect if the seat belts are fastened. The
Advanced Air Bag System monitors the
severity of a collision and seat belt
usage then inflates the air bags as
needed. Failure to properly wear seat
belts can increase the risk or severity of
injury in an accident.
.
The front passenger seat is equipped
with occupant classification sensors
(weight sensors) that turn the front
passenger air bag OFF under some
conditions. These sensors are only used
in this seat. Failure to be properly seated
and wearing the seat belt can increase
the risk or severity of injury in an
accident. See “Front passenger air bag
and status light” (P.1-48).
.
SSS0007
SSS0008
SSS0006
SSS0009
Keep hands on the outside of the
steering wheel. Placing them inside the
steering wheel rim could increase the
risk of injury if the front air bag inflates.
1-42 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(61,1)
WARNING
.
Never let children ride unrestrained or
extend their hands or face out of the
window. Do not attempt to hold them in
your lap or arms. Some examples of
dangerous riding positions are shown in
the illustrations.
.
Children may be severely injured or
killed when the front air bags, side air
bags or curtain air bags inflate if they are
not properly restrained. Pre-teens and
children should be properly restrained in
the rear seat, if possible.
SSS0099
.
SSS0059A
Even with the INFINITI Advanced Air Bag
System, never install a rear-facing child
restraint in the front seat. An inflating
front air bag could seriously injure or kill
your child. See “Child restraints” (P.121) for details.
SSS0188A
SSS0100
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-43
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(62,1)
SSS0140
.
The curtain air bags ordinarily will not
inflate in the event of a front impact, rear
impact, or lower severity side collision.
Always wear your seat belts to help
reduce the risk or severity of injury in
various kinds of accidents.
.
The seat belts, the side air bags and
curtain air bags are most effective when
you are sitting well back and upright in
the seat. The side air bag and curtain air
bag inflate with great force. Do not allow
anyone to place their hand, leg or face
near the side air bag on the side of the
seatback of the front seat or near the
side roof rails. Do not allow anyone
sitting in the front seats or rear outboard
seats to extend their hand out of the
window or lean against the door. Some
examples of dangerous riding positions
are shown in the previous illustrations.
.
When sitting in the rear seat, do not hold
onto the seatback of the front seat. If the
supplemental side air bag inflates, you
may be seriously injured. Be especially
careful with children, who should always
be properly restrained. Some examples
of dangerous riding positions are shown
in the illustrations.
SSS0159
WARNING
Front seat-mounted side-impact supplemental air bags and roof-mounted curtain sideimpact and rollover supplemental air bags:
.
The side air bags ordinarily will not
inflate in the event of a front impact, rear
impact, rollover, or lower severity side
collision. Always wear your seat belts to
help reduce the risk or severity of injury
in various kinds of accidents.
SSS0162
1-44 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(63,1)
.
Do not use seat covers on the front
seatbacks. They may interfere with side
air bag inflation.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-45
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(64,1)
8.
9.
10.
11.
12.
Pressure sensors in door
Satellite sensors
Seat belts with pretensioners
Air bag Control Unit (ACU)
Lap outer pretensioners
INFINITI ADVANCED AIR BAG SYSTEM (frontCV37D1-F3E1E0CD-4853-4DEE-8BF7-FDF8511DF69C
seats)
WARNING
To ensure proper operation of the passenger’s Advanced Air Bag System, observe the
following items.
JVR0507X
1.
2.
3.
4.
Crash zone sensor
Supplemental front air bag modules
(INFINITI Advanced Air Bags)
Front seat-mounted side-impact supplemental air bags
Roof-mounted curtain side-impact
and rollover supplemental air bags
5.
6.
7.
Occupant classification sensors
(weight sensors)
Occupant classification system control unit
Roof-mounted curtain side-impact
and rollover supplemental air bag
inflators
.
Do not allow a passenger in the rear seat
to push or pull on the seatback pocket.
.
Do not place heavy loads heavier than
9.1 lbs. (4 kg) on the seatback, head
restraint or in the seatback pocket.
.
Make sure that there is nothing pressing
against the rear of the seatback, such as
a child restraint installed in the rear seat
or an object stored on the floor.
.
Make sure that there is no object placed
under the front passenger seat.
.
Make sure that there is no object placed
between the seat cushion and center
console or between the seat cushion and
1-46 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(65,1)
the door.
.
Confirm the operating condition with the
front passenger air bag status light.
.
If you notice that the front passenger air
bag status light is not operating as
described in this section, it is recommended you visit an INFINITI retailer to
check the passenger seat Advanced Air
Bag System.
.
Until you have confirmed with a retailer
that your passenger seat Advanced Air
Bag System is working properly, position the occupants in the rear seating
positions.
This vehicle is equipped with the INFINITI
Advanced Air Bag System for the driver and
front passenger seats. This system is
designed to meet certification requirements under U.S. regulations. It is also
permitted in Canada. All of the information, cautions and warnings in this manual
apply and must be followed.
The driver supplemental front-impact air
bag is located in the center of the steering
wheel. The front passenger supplemental
front-impact air bag is mounted in the
instrument panel above the glove box. The
front air bags are designed to inflate in
higher severity frontal collisions, although
they may inflate if the forces in another
type of collision are similar to those of a
higher severity frontal impact. They may
not inflate in certain frontal collisions.
Vehicle damage (or lack of it) is not always
an indication of proper front air bag
operation.
The INFINITI Advanced Air Bag System has
dual stage air bag inflators. The system
monitors information from the crash zone
sensor, the Air bag Control Unit (ACU), seat
belt buckle switches and the occupant
classification sensors (weight sensors).
Inflator operation is based on the severity
of a collision and seat belt usage for the
driver. For the front passenger, the occupant classification sensors are also monitored. Based on information from the
sensors, only one front air bag may inflate
in a crash, depending on the crash severity
and whether the front occupants are belted
or unbelted. Additionally, the front passenger air bag may be automatically turned
OFF under some conditions, depending on
the information provided by the occupant
classification sensors. If the front passenger air bag is OFF, the front passenger air
bag status light will be illuminated. (See
“Front passenger air bag and status light”
(P.1-48) for further details.) One front air
bag inflating does not indicate improper
performance of the system.
If you have any questions about your air
bag system, it is recommended you visit an
INFINITI retailer to obtain information
about the system. If you are considering
modification of your vehicle due to a
disability, you may also contact an INFINITI
retailer. Contact information is contained in
the front of this Owner’s Manual.
When a front air bag inflates, a fairly loud
noise may be heard, followed by release of
smoke. This smoke is not harmful and does
not indicate a fire. Care should be taken
not to inhale it, as it may cause irritation
and choking. Those with a history of a
breathing condition should get fresh air
promptly.
Front air bags, along with the use of seat
belts, help to cushion the impact force on
the head and chest of the front occupants.
They can help save lives and reduce
serious injuries. However, an inflating front
air bag may cause facial abrasions or other
injuries. Front air bags do not provide
restraint to the lower body.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-47
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(66,1)
Even with INFINITI advanced air bags, seat
belts should be correctly worn and the
driver and passenger seated upright as far
as practical away from the steering wheel
or instrument panel. The front air bags
inflate quickly in order to help protect the
front occupants. Because of this, the force
of the front air bag inflating can increase
the risk of injury if the occupant is too close
to, or is against, the air bag module during
inflation.
of injury in an accident.
The front air bags deflate quickly after a
collision.
The front air bags operate only when the
ignition switch is in the ON position.
After placing the ignition switch in the ON
position, the supplemental air bag warning light illuminates. The supplemental air
bag warning light will turn off after about 7
seconds if the system is operational.
JVR0192X
Front passenger air bag and status
light
CV37D1-251B11C4-1A1B-4A64-9371-B0EC203F33CE
WARNING
The front passenger air bag is designed to
automatically turn OFF under some conditions. Read this section carefully to learn
how it operates. Proper use of the seat, seat
belt and child restraints is necessary for
most effective protection. Failure to follow
all instructions in this manual concerning
the use of seats, seat belts and child
restraints can increase the risk or severity
1-48 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(67,1)
Status light:
The front passenger seat is equipped with an occupant classification sensors (weight sensors) that turn the front passenger air bag on or
off depending on the weight applied to the front passenger seat. The status of the front passenger air bag (ON or OFF) is indicated by the
front passenger air bag status light
which is located on the instrument panel.
After the ignition switch is placed in the ON position, the front passenger air bag status light illuminates for about 7 seconds and then
turns off or remains illuminated depending on the front passenger seat occupied status. The light operates as follows:
CONDITION
DESCRIPTION
PASSENGER AIR BAG STATUS LIGHT
)
(
FRONT PASSENGER AIR BAG STATUS
Empty
Empty front passenger seat
ON
(illuminated)
INHIBITED
Nobody/Somebody
Bag or Child or Child Restraint or Small
Adult in the front passenger seat
ON
(illuminated)
INHIBITED
Adult
Adult in the front passenger seat
OFF
(dark)
ACTIVATED
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-49
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(68,1)
In addition to the above, certain objects
placed on the front passenger seat may
also cause the light to operate as described above depending on their weight.
For additional information related to the
normal operation and troubleshooting of
this occupant classification sensor system,
please refer to “Normal operation” (P.1-51)
and “Troubleshooting” (P.1-52).
Front passenger
air bag:
CV37D1-C6271740-9F33-47C5-9A49-855A85AE074E
The front passenger air bag is designed to
automatically turn OFF when the vehicle is
operated under some conditions as described below in accordance with U.S.
regulations. If the front passenger air bag
is OFF, it will not inflate in a crash. The
driver air bag and other air bags in your
vehicle are not part of this system.
The purpose of the regulation is to help
reduce the risk of injury or death from an
inflating air bag to certain front passenger
seat occupants, such as children, by
requiring the air bag to be automatically
turned OFF. Certain sensors are used to
meet the requirements.
The occupant classification sensor in this
vehicle is a weight sensor. It is designed to
detect an occupant and objects on the seat
by weight. For example, if a child is in the
front passenger seat, the Advanced Air Bag
System is designed to turn the passenger
air bag OFF in accordance with the regulations. Also, if a child restraint of the type
specified in the regulations is on the seat,
its weight and the child’s weight can be
detected and cause the air bag to turn OFF.
Front passenger seat adult occupants who
are properly seated and using the seat belt
as outlined in this manual should not
cause the passenger air bag to be automatically turned OFF. For small adults it
may be turned OFF, however, if the
occupant takes his/her weight off the seat
cushion (for example, by not sitting upright, by sitting on an edge of the seat, or
by otherwise being out of position), this
could cause the sensor to turn the air bag
OFF. Always be sure to be seated and
wearing the seat belt properly for the most
effective protection by the seat belt and
supplemental air bag.
INFINITI recommends that pre-teens and
children be properly restrained in a rear
seat. INFINITI also recommends that appropriate child restraints and booster seats be
properly installed in a rear seat. If this is
not possible, the occupant classification
sensor is designed to operate as described
above to turn the front passenger air bag
OFF for specified child restraints as required by the regulations. Failing to properly secure child restraints and to use the
ALR mode may allow the restraint to tip or
move in a collision or sudden stop. This can
also result in the passenger air bag
inflating in a crash instead of being OFF.
For additional information, refer to “Child
restraints” (P.1-21) for proper use and
installation.
If the front passenger seat is not occupied,
the passenger air bag is designed not to
inflate in a crash. However, heavy objects
placed on the seat could result in air bag
inflation, because of the object’s weight
detected by the occupant classification
sensor. Other conditions could also result
in air bag inflation, such as if a child is
standing on the seat, or if two children are
on the seat, contrary to the instructions in
this manual. Always be sure that you and
all vehicle occupants are seated and
restrained properly.
Using the front passenger air bag status
light, you can monitor when the front
passenger air bag is automatically turned
OFF.
1-50 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(69,1)
If an adult occupant is in the seat but the
front passenger air bag status light is
illuminated (indicating that the air bag is
OFF), it could be that the person is a small
adult, or is not sitting on the seat properly
or not using the seat belt properly.
If a child restraint must be used in the front
seat, the front passenger air bag status
light may or may not be illuminated,
depending on the size of the child and
the type of child restraint being used. If the
front passenger air bag status light is not
illuminated (indicating that the air bag
might inflate in a crash), it could be that
the child restraint or seat belt is not being
used properly. Make sure that the child
restraint is installed properly, the seat belt
is used properly and the occupant is
positioned properly. If the front passenger
air bag status light is still not illuminated,
reposition the occupant or child restraint in
a rear seat.
If the front passenger air bag status light
will not illuminate even though you believe
that the child restraint, the seat belts and
the occupant are properly positioned, it is
recommended that you take your vehicle to
an INFINITI retailer. An INFINITI retailer can
check system status by using a special
tool. However, until you have confirmed
with your retailer that your air bag is
working properly, reposition the occupant
or child restraint in a rear seat.
The INFINITI Advanced Air Bag System and
front passenger air bag status light will
take a few seconds to register a change in
the passenger seat status. For example, if a
large adult who is sitting in the front
passenger seat exits the vehicle, the front
passenger air bag status light will go from
OFF to ON for a few seconds and then to
OFF. This is normal system operation and
does not indicate a malfunction.
If a malfunction occurs in the front passenger air bag system, the supplemental
air bag warning light
, located in the
meter and gauges area of the instrument
panel, will be illuminated (blinking or
steadily lit). Have the system checked. It
is recommended you visit an INFINITI
retailer for this service.
Normal operation:
CV37D1-33CF3EF1-20FE-4FE1-B4D2-D7CDE97EF1F4
In order for the occupant classification
sensor system to classify the front passenger based on weight, please follow the
precautions and steps outlined below:
Precautions
. Make sure that there are no objects
weighing over 9.1 lbs (4 kg) hanging on
the seat or placed in the seatback
pocket.
. Make sure that a child restraint or other
object is not pressing against the rear
of the seatback.
. Make sure that a rear passenger is not
pushing or pulling on the back of the
front passenger seat.
. Make sure that the front passenger seat
or seatback is not forced back against
an object on the seat or floor behind it.
. Make sure that there is no object placed
under the front passenger seat.
Steps
1. Adjust the seat as outlined in “Seats”
(P.1-2). Sit upright, leaning against the
seatback, and centered on the seat
cushion with your feet comfortably
extended to the floor.
2. Make sure there are no objects on your
lap.
3. Fasten the seat belt as outlined in “Seat
belts” (P.1-11). Front passenger seat
belt buckle status is monitored by the
occupant classification sensor system,
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-51
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(70,1)
and is used as an input to determine
occupancy status. So, it is highly
recommended that the front passenger
fastens his/her seat belt.
4. Remain in this position for 30 seconds
allowing the system to classify the front
passenger before the vehicle is put into
motion.
5. Ensure proper classification by checking the front passenger air bag status
light.
NOTE:
This vehicle’s occupant classification sensor system generally keeps the classification locked during driving, so it is
important that you confirm that the front
passenger is properly classified prior to
driving. However, the occupant classification sensor may recalculate the weight of
the occupant under some conditions (both
while driving and when stopped), so the
front passenger seat occupant should
continue to remain seated as outlined
above.
Troubleshooting:
CV37D1-9078694B-5AB0-4C79-A12B-0ECC32C0E0B0
If you think the front passenger air bag
status light is incorrect:
1. If the light is ON with an adult occupying the front passenger seat:
. Occupant is a small adult - the air
bag status light is functioning as
intended. The front passenger air
bag is suppressed.
However, if the occupant is not a small
adult, then this may be due to the
following conditions that may be interfering with the weight sensors:
. Occupant is not sitting upright,
leaning against the seatback, and
centered on the seat cushion with
his/her feet comfortably extended to
the floor.
. A child restraint or other object
pressing against the rear of the
seatback.
. A rear passenger pushing or pulling
on the back of the front passenger
seat.
. Forcing the front seat or seatback
against an object on the seat or floor
behind it.
.
.
An object placed under the front
passenger seat.
An object placed between the seat
cushion and center console or between the seat cushion and the door.
If the vehicle is moving, please come to
a stop when it is safe to do so. Check
and correct any of the above conditions. Restart the vehicle and wait 1
minute.
NOTE:
A system check will be performed
during which the front passenger air
bag status light will remain lit for
about 7 seconds initially.
If the light is still ON after this, the
person should be advised not to ride in
the front passenger seat and the
vehicle should be checked by an
INFINITI retailer as soon as possible.
2. If the light is OFF with a small adult,
child or child restraint occupying the
front passenger seat:
This may be due to the following
conditions that may be interfering with
the weight sensors:
. Small adult or child is not sitting
upright, leaning against the seat-
1-52 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(71,1)
.
.
.
.
.
.
.
back, and centered on the seat
cushion with his/her feet comfortably extended to the floor.
The child restraint is not properly
installed as outlined in “Child restraints” (P.1-21).
An object weighing over 9.1 lbs (4
kg) hanging on the seat or placed in
the seatback pocket.
A child restraint or other object
pressing against the rear of the
seatback.
A rear passenger pushing or pulling
on the back of the front passenger
seat.
Forcing the front seat or seatback
against an object on the seat or floor
behind it.
An object placed under the front
passenger seat.
An object placed between the seat
cushion and center console.
If the vehicle is moving, please come to
a stop when it is safe to do so. Check
and correct any of the above conditions. Restart the vehicle and wait 1
minute.
NOTE:
A system check will be performed
during which the front passenger air
bag status light will remain lit for
about 7 seconds initially.
If the light is still OFF after this, the
small adult, child or child restraint
should be repositioned in the rear seat
and the vehicle should be checked by
an INFINITI retailer as soon as possible.
.
Do not place objects with sharp edges on
the seat. Also, do not place heavy
objects on the seat that will leave
permanent impressions in the seat. Such
objects can damage the seat or occupant
classification sensors (weight sensors).
This can affect the operation of the air
bag system and result in serious personal injury.
.
Do not use water or acidic cleaners (hot
steam cleaners) on the seat. This can
damage the seat or occupant classification sensors. This can also affect the
operation of the air bag system and
result in serious personal injury.
.
Immediately after inflation, several front
air bag system components will be hot.
Do not touch them; you may severely
burn yourself.
.
No unauthorized changes should be
made to any components or wiring of
the air bag system. This is to prevent
accidental inflation of the supplemental
air bag or damage to the supplemental
air bag system.
.
Do not make unauthorized changes to
your vehicle’s electrical system, suspension system or front end structure. This
3. If the light is OFF with no front
passenger and no objects on the front
passenger seat, the vehicle should be
checked by an INFINITI retailer as soon
as possible.
Other supplemental front-impact
air bag precautions
CV37D1-BA9AC028-4097-4FF6-B42B-E2048C452E5F
WARNING
.
Do not place any objects on the steering
wheel pad or on the instrument panel.
Also, do not place any objects between
any occupant and the steering wheel or
instrument panel. Such objects may
become dangerous projectiles and cause
injury if the front air bags inflate.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-53
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(72,1)
could affect proper operation of the front
air bag system.
.
Tampering with the air bag system may
result in serious personal injury. Tampering includes changes to the steering
wheel and the instrument panel assembly by placing material over the steering
wheel pad and above the instrument
panel or by installing additional trim
material around the air bag system.
.
Removing or modifying the front passenger seat may affect the function of
the air bag system and result in serious
personal injury.
.
Modifying or tampering with the front
passenger seat may result in serious
personal injury. For example, do not
change the front seats by placing material on the seat cushion or by installing
additional trim material, such as seat
covers, on the seat that is not specifically designed to assure proper air bag
operation. Additionally, do not stow any
objects under the front passenger seat
or the seat cushion and seatback. Such
objects may interfere with the proper
operation of the occupant classification
sensors.
*
.
No unauthorized changes should be
made to any components or wiring of
the seat belt system. This may affect the
front air bag system. Tampering with the
seat belt system may result in serious
personal injury.
.
It is recommended you visit an INFINITI
retailer for work on and around the front
air bag. It is also recommended you visit
an INFINITI retailer for installation of
electrical equipment. The Supplemental
Restraint System (SRS) wiring harnesses* should not be modified or
disconnected. Unauthorized electrical
test equipment and probing devices
should not be used on the air bag
system.
.
A cracked windshield should be replaced
immediately by a qualified repair facility.
A cracked windshield could affect the
function of the supplemental air bag
system.
appropriate sections in this Owner’s Manual.
The SRS wiring harness connectors
are yellow and orange for easy
identification.
When selling your vehicle, we request that
you inform the buyer about the front air
bag system and guide the buyer to the
1-54 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(73,1)
collision are similar to those of a higher
severity impact. They are designed to
inflate on the side where the vehicle is
impacted. They may not inflate in certain
side collisions.
Curtain air bags are also designed to
inflate in certain types of rollover collisions
or near rollovers. As a result, certain
vehicle movements (for example, during
severe off-roading) may cause the curtain
air bags to inflate.
SSS0521
FRONT SEAT-MOUNTED SIDE-IMPACT SUPPLEMENTAL AIR BAG AND
ROOF-MOUNTED CURTAIN SIDE-IMPACT AND ROLLOVER SUPPLEMENTAL AIR BAG
SYSTEMS
CV37D1-6DEEA2BB-CA37-4862-BE7D-9A1C86F723D1
The side air bags are located in the outside
of the seatback of the front seats. The
curtain air bags are located in the side roof
rails. All of the information, cautions and
warnings in this manual apply and must be
followed. The side air bags and curtain air
bags are designed to inflate in higher
severity side collisions, although they may
inflate if the forces in another type of
Vehicle damage (or lack of it) is not always
an indication of proper supplemental side
air bag and curtain side-impact air bag
operation.
When side air bags and curtain air bags
inflate, a fairly loud noise may be heard,
followed by release of smoke. This smoke
is not harmful and does not indicate a fire.
Care should be taken not to inhale it, as it
may cause irritation and choking. Those
with a history of a breathing condition
should get fresh air promptly.
Side air bags, along with the use of seat
belts, help to cushion the impact force on
the chest of the front occupants. Curtain air
bags help to cushion the impact force to
the head of occupants in the front and rear
outboard seating positions in all rows.
They can help save lives and reduce
serious injuries. However, an inflating side
air bags and curtain air bags may cause
abrasions or other injuries. Side air bags
and curtain air bags do not provide
restraint to the lower body.
The seat belts should be correctly worn and
the driver and passenger seated upright as
far as practical away from the side air bag.
Rear seat passengers should be seated as
far away as practical from the door
finishers and side roof rails. The side air
bags and curtain air bags inflate quickly in
order to help protect the occupants.
Because of this, the force of the side air
bags and curtain air bags inflating can
increase the risk of injury if the occupant is
too close to, or is against, these air bag
modules during inflation. In a rollover, the
curtain air bags on both sides are designed
to inflate. Under both side-impact situations, the curtain air bags will remain
inflated for a short period of time.
The side air bags and curtain air bags
operate only when the ignition switch is in
the ON position.
After placing the ignition switch in the ON
position, the supplemental air bag warning light illuminates. The air bag warning
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-55
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(74,1)
light will turn off after about 7 seconds if
the systems are operational.
.
WARNING
.
Do not place any objects near the seatback of the front seats. Also, do not
place any objects (an umbrella, bag, etc.)
between the door finisher and the front
seat. Such objects may become dangerous projectiles and cause injury if side
air bag inflates.
.
Right after inflation, several side air
bags and curtain air bag system components will be hot. Do not touch them; you
may severely burn yourself.
.
No unauthorized changes should be
made to any components or wiring of
side air bag and curtain air bags. This is
to prevent damage to or accidental
inflation of the side air bag and curtain
air bag systems.
.
Do not make unauthorized changes to
your vehicle’s electrical system, suspension system or side panel. This could
affect proper operation of the side air
bag and curtain air bag systems.
.
*
Tampering with the air bag system may
result in serious personal injury. For
example, do not change the front seats
by placing material near the seatback or
by installing additional trim material,
such as seat covers, around the side air
bags.
It is recommended you visit an INFINITI
retailer for work on and around the side
air bag and curtain air bag. It is also
recommended you visit an INFINITI retailer for installation of electrical equipment. The Supplemental Restraint
System (SRS) wiring harnesses* should
not be modified or disconnected. Unauthorized electrical test equipment and
probing devices should not be used on
the side-impact air bag system.
SEAT BELTS WITH PRETENSIONERS
(front seats)
CV37D1-FB5B531B-B3DD-4760-AA66-A1D2A79F9F19
WARNING
.
The pretensioners cannot be reused after
activation. They must be replaced together with the retractor and buckle as a
unit.
.
If the vehicle becomes involved in a
collision but a pretensioner is not
activated, be sure to have the pretensioner system checked and, if necessary,
replaced. It is recommended you visit an
INFINITI retailer for this service.
.
No unauthorized changes should be
made to any components or wiring of
the pretensioners. This is to prevent
damage to or accidental activation of
the pretensioner system. Tampering with
the pretensioner system may result in
serious personal injury.
.
It is recommended you visit an INFINITI
retailer for work on and around the
pretensioner system. It is also recommended you visit an INFINITI retailer for
installation of electrical equipment. Unauthorized electrical test equipment and
The SRS wiring harness connectors
are yellow and orange for easy
identification.
When selling your vehicle, we request that
you inform the buyer about the side air bag
and curtain air bag systems and guide the
buyer to the appropriate sections in this
Owner’s Manual.
1-56 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(75,1)
probing devices should not be used on
the pretensioner system.
.
If you need to dispose of the pretensioner or scrap the vehicle, it is recommended you visit an INFINITI retailer for
this service. Correct pretensioner disposal procedures are set forth in the
appropriate INFINITI Service Manual.
Incorrect disposal procedures could
cause personal injury.
.
If there is an impact to your vehicle from
any direction, your Occupant Classification Sensor (OCS) should be checked. It
is recommended an INFINITI retailer performs this service to verify it is still
functioning correctly. The OCS should be
checked even if no air bags deploy as a
result of the impact. Failure to verify
proper OCS function may result in an
improper air bag deployment resulting in
injury or death.
The pretensioner system may activate with
the supplemental air bag system in certain
types of collisions. Working with the seat
belt retractor, it helps tighten the seat belt
when the vehicle becomes involved in
certain types of collisions, helping to
restrain front seat occupants.
The pretensioner is encased with the seat
belt retractor. These seat belts are used the
same way as conventional seat belts.
When a pretensioner seat belt activates,
smoke is released and a loud noise may be
heard. The smoke is not harmful, and it
does not indicate a fire. Care should be
taken not to inhale it as it may cause
irritation and choking. Those with a history
of a breathing condition should get fresh
air promptly.
After pretensioner activation, load limiters
allow the seat belt to release webbing (if
necessary) to reduce forces against the
chest.
The supplemental air bag warning light
is used to indicate malfunctions in the
pretensioner system. (See “Supplemental
air bag warning light” (P.1-58) for more
details.) If the operation of the supplemental air bag warning light indicates
there is a malfunction, have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
SSS1016
SUPPLEMENTAL AIR BAG WARNING
LABELS CV37D1-80933CBA-9442-4834-8771-28C9CCEF9D69
Warning labels about the supplemental
front-impact air bag systems are placed in
the vehicle as shown in the illustration.
SRS air bag
CV37D1-A46E243E-0A07-44FE-83A1-CC6B393625E9
1 are located on the
The warning labels *
surface of the sun visors.
When selling your vehicle, we request that
you inform the buyer about the seat belt
pretensioners and guide the buyer to the
appropriate sections in this Owner’s Manual.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-57
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(76,1)
servicing:
SPA1097
. The supplemental air bag warning light
remains on after approximately 7 seconds.
. The supplemental air bag warning light
flashes intermittently.
. The supplemental air bag warning light
does not come on at all.
Under these conditions, the air bag or
pretensioner systems may not operate
properly. They must be checked and
repaired. It is recommended you visit an
INFINITI retailer for this service.
SUPPLEMENTAL AIR BAG WARNING
LIGHT
CV37D1-B56BABA8-6680-4AC1-806E-CE3B559CB31A
The supplemental air bag warning light,
displaying
in the instrument panel,
monitors the circuits for the air bag
systems, pretensioners and all related
wiring.
When the ignition switch is in the ON
position, the supplemental air bag warning
light illuminates for about 7 seconds and
then turns off. This means the SRS air bag
systems are operational.
WARNING
If the supplemental air bag warning light is
on, it could mean that the front air bag, side
air bag, curtain air bag and/or pretensioner
systems will not operate in an accident. To
help avoid injury to yourself or others, have
your vehicle checked as soon as possible. It
is recommended you visit an INFINITI retailer
for this service.
If any of the following conditions occur, the
air bag and/or pretensioner systems need
REPAIR AND REPLACEMENT PROCEDURE
CV37D1-6F17C37B-9666-4639-BFD5-AF1EBFBE5694
The front air bags, side air bags, curtain air
bags and pretensioners are designed to
activate on a one-time-only basis. As a
reminder, unless it is damaged, the supplemental air bag warning light will remain
illuminated after inflation has occurred.
These systems should be repaired and/or
replaced as soon as possible. It is recommended you visit an INFINITI retailer for
this service.
When maintenance work is required on the
vehicle, the front air bags, side air bags,
curtain air bags, pretensioners and related
parts should be pointed out to the person
conducting the maintenance. The ignition
switch should always be in the LOCK
position when working under the hood or
inside the vehicle.
WARNING
.
Once a front air bag, side air bag, or
curtain air bag has inflated, the air bag
module will not function again and must
be replaced. Additionally, the activated
pretensioner must also be replaced. The
1-58 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(77,1)
air bag module and pretensioner should
be replaced. It is recommended you visit
an INFINITI retailer for this service.
However, the air bag module and pretensioner system cannot be repaired.
.
The front air bag, side air bag, curtain air
bag and the pretensioner system should
be inspected if there is any damage to
the front end or side portion of the
vehicle. It is recommended you visit an
INFINITI retailer for this service.
.
If you need to dispose of the supplemental air bag or pretensioner or scrap
the vehicle, it is recommended you visit
an INFINITI retailer. Correct supplemental air bag and seat belt pretensioner
system disposal procedures are set forth
in the appropriate INFINITI Service Manual. Incorrect disposal procedures could
cause personal injury.
.
If there is an impact to your vehicle from
any direction, your Occupant Classification Sensor (OCS) should be checked by
an INFINITI retailer to verify it is still
functioning correctly. The OCS should be
checked even if no air bags deploy as a
result of the impact. Failure to verify
proper OCS function may result in an
improper air bag deployment resulting in
injury or death.
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-59
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(78,1)
MEMO
1-60 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(79,1)
MEMO
Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
1-61
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(80,1)
MEMO
1-62 Safety — Seats, seat belts and supplemental restraint system
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(81,1)
2 Instruments and controls
Cockpit ...............................................................
...
2-3
Instrument panel ................................................
...
2-5
Meters and gauges .............................................
...
2-6
Speedometer and odometer ...........................
...
2-7
Tachometer .....................................................
...
2-8
Engine coolant temperature gauge .................
...
2-8
Fuel gauge .....................................................
...
2-9
Compass (if so equipped) ...................................
...
2-9
Zone variation change procedure ..................
...
2-11
Warning lights, indicator lights and
audible reminders .............................................
...
2-12
Checking lights .............................................
...
2-12
Warning lights ..............................................
...
2-12
Indicator lights .............................................
...
2-18
Audible reminders ........................................
...
2-20
Vehicle information display ...............................
...
2-21
Indicators for operation ................................
...
2-24
Indicators for maintenance ...........................
...
2-28
Trip computer ...............................................
...
2-31
Clock and outside air temperature ................
...
2-34
Security systems ..............................................
...
2-34
Vehicle Security System ................................
...
2-35
INFINITI Vehicle Immobilizer System .............
...
2-36
Condition:
Wiper and washer switch .................................
...
Rain-sensing auto wiper system (if
so equipped) ..............................................
...
Rear window and outside mirror
defroster switch ...............................................
...
Headlight and turn signal switch ......................
...
Headlight switch .........................................
...
Turn signal switch .......................................
...
Fog light switch ..........................................
...
Horn .................................................................
...
Vehicle Dynamic Control (VDC) OFF switch ........
...
Heated seats (if so equipped) ...........................
...
Operation with switch .................................
...
Operation with touch screen .......................
...
AUTO mode setting .....................................
...
Heated steering wheel (if so equipped) ............
...
Power outlets ...................................................
...
Storage ............................................................
...
Cup holders ................................................
...
Soft bottle holder ........................................
...
Sunglasses holder ......................................
...
Glove box ...................................................
...
Console box ................................................
...
[ Edit: 2016/ 4/ 27
2-37
2-39
2-40
2-40
2-40
2-46
2-47
2-47
2-47
2-48
2-49
2-49
2-49
2-49
2-50
2-51
2-51
2-52
2-52
2-53
2-53
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(82,1)
Card holder ..................................................
...
Storage box ..................................................
...
Coat hooks ...................................................
...
Trunk hooks .................................................
...
Windows ...........................................................
...
Power windows ............................................
...
Moonroof (if so equipped) ................................
...
Power moonroof ...........................................
...
Interior lights ....................................................
...
Map lights ....................................................
...
Console light (if so equipped) .......................
...
Interior light control switch ...........................
...
Vanity mirror lights ...........................................
...
Trunk light ........................................................
...
Condition:
2-53
2-54
2-54
2-54
2-55
2-55
2-58
2-58
2-60
2-60
2-60
2-60
2-61
2-62
Courtesy light ...................................................
...
HomeLink® Universal Transceiver (if
so equipped) ....................................................
...
Programming HomeLink® ............................
...
Programming HomeLink® for Canadian
customers and gate openers .......................
...
Operating the HomeLink®
Universal Transceiver ..................................
...
Programming troubleshooting .....................
...
Clearing the programmed information .........
...
Reprogramming a single
HomeLink® button ......................................
...
If your vehicle is stolen ...............................
...
[ Edit: 2016/ 4/ 27
2-62
2-62
2-63
2-65
2-65
2-65
2-66
2-66
2-66
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(83,1)
COCKPIT
4.
CV37D1-83D46913-7F0C-4CB0-A756-275B43D9E03A
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
JVC0942X
1.
2.
3.
Side ventilator (P.4-2)
Headlight, fog light and turn signal
switch (P.2-40)
Steering wheel
— Horn (P.2-47)
— Driver supplemental air bag
(P.1-40)
— Heated steering wheel (if so
equipped) (P.2-49)
— Power steering (P.5-130)
16.
Windshield wiper and washer switch
(P.2-37)
Hazard warning flasher switch (P.6-2)
Shift lever (P.5-16)
INFINITI controller*
Vehicle Dynamic Control (VDC) OFF
switch (P.2-47, P.5-136)
Idling Stop OFF switch (if so equipped)
(P.5-140)
Trunk lid release switch (P.3-24)
Instrument brightness control switch
(P.2-46)
TRIP/RESET switch for twin trip odometer (P.2-7)
Electric tilting/telescopic steering
wheel switch (P.3-28)
Manual tilting/telescopic steering
wheel lever (P.3-28)
Steering-wheel-mounted controls (left
side)
— Audio control steering switch*
— Hands-Free Phone System switch*
— Voice recognition system switch*
Steering-wheel-mounted controls
(right side)
— Trip computer switch (P.2-31)
— Cruise control switches (if so
equipped) (P.5-74)
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(84,1)
— Intelligent Cruise Control (ICC)
switches (if so equipped) (P.5-76)
— Dynamic driver assistance switch
(if so equipped) (P. 5-27, P.5-35,
P.5-50, P.5-96)
17. INFINITI Drive Mode Selector (P.5-23)
*: Refer to the Infiniti InTouch Owner’s
Manual.
2-4
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(85,1)
INSTRUMENT PANEL
8.
CV37D1-139F898F-EF61-4933-9424-E1767A8A4A89
9.
10.
11.
12.
13.
14.
15.
16.
17.
*:
Rear window and outside mirror
defroster switch (P.2-40)
Front passenger supplemental air bag
(P.1-40)
Hood release handle (P.3-23)
Fuse box cover (P.8-25)
Parking brake (P.5-22)
Storage box (P.2-54) and power outlet
(P.2-50)
Seat heater switch (if so equipped)
(P.2-48)
Audio system*
Trunk release power cancel switch
(P.3-25)
Glove box (P.2-53)
Refer to the Infiniti InTouch Owner’s
Manual.
JVC0969X
1.
2.
3.
4.
Paddle shifter (if so equipped) (P.5-18)
Meters and gauges (P.2-6)
— Clock (P.2-34)
Push-button ignition switch (P.5-12)
Center ventilator (P.4-2)
5.
6.
7.
Automatic climate control system*
Upper touch screen display* (upper
display) and Navigation system* (if so
equipped)
Lower touch screen display* (lower
display)
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(86,1)
METERS AND GAUGES
CV37D1-691FA2D1-00DE-4C62-B62C-FE0C7AA320F1
CAUTION
.
For cleaning, use a soft cloth, dampened
with water. Never use a rough cloth,
alcohol, benzine, thinner or any kind of
solvent or paper towel with a chemical
cleaning agent. They will scratch or
cause discoloration to the lens.
.
Do not spray any liquid such as water on
the meter lens. Spraying liquid may
cause the system to malfunction.
JVC0428X
1.
2.
3.
4.
5.
2-6
Tachometer* (P.2-8)
Warning and indicator lights (P.2-12)
Speedometer* (P.2-7)
Engine coolant temperature gauge*
(P.2-8)
Vehicle information display (P.2-21)/
Odometer/twin trip odometer (P.2-7)
6. Fuel gauge* (P.2-9)
*: The needle indicators may move slightly
after the ignition switch is placed in the
OFF position. This is not a malfunction.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(87,1)
Changing the
display:
CV37D1-5223072E-4C09-45EF-8F2F-B1C5679FE4D2
3 under
Pushing the TRIP RESET switch *
the combination meter panel changes the
display as follows:
TRIP A ? TRIP B ? TRIP A
Resetting the
trip odometer:
CV37D1-1784BFF5-79F7-43F1-9885-3A5D19636CE8
3 for more
Pushing the TRIP RESET switch *
than 1 second resets the trip odometer to
zero.
JVI0636X
JVI0637X
Speedometer
Odometer/twin trip odometer
SPEEDOMETER
AND ODOMETER
CV37D1-CD0DE725-3134-48E8-A8F7-FE79D9F509C5
Odometer/twin
trip odometer
CV37D1-3F65DB18-06BA-46B4-BF90-A423A80A9340
Speedometer
CV37D1-6C1D5CB1-6492-445B-825B-135C5B283C5C
1 and twin trip odometer
The odometer *
2 are displayed in the vehicle information
*
display when the ignition switch is in the
ON position.
The speedometer indicates vehicle speed
in miles per hour (MPH) and kilometers per
hour (km/h).
The odometer records the total distance
the vehicle has been driven.
The twin trip odometer records the distance of individual trips.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(88,1)
CAUTION
JVI0638X
TACHOMETER
CV37D1-ED042B9F-86CF-48B5-969C-C2981187A825
The tachometer indicates engine speed in
revolutions per minute (RPM). Do not rev
1 .
the engine into the red zone *
The scale length and the red zone vary with
the engine model.
CAUTION
When engine speed approaches the red
zone, shift to a higher gear or reduce engine
speed. Operating the engine in the red zone
may cause serious engine damage.
2-8
JVI0639X
If the gauge indicates the engine coolant
temperature is near the hot (H) end of the
normal range, reduce vehicle speed to
decrease the temperature. If the gauge is
over the normal range, stop the vehicle as
soon as safely possible and let the engine
idle. If the engine is overheated, continued
operation of the vehicle may seriously
damage the engine. See “If your vehicle
overheats” (P.6-16) for immediate action
required.
ENGINE COOLANT TEMPERATURE
GAUGE CV37D1-0B4133D2-A999-449F-81B0-E064C24AD12C
The gauge indicates the engine coolant
temperature.
The engine coolant temperature is within
the normal range when the gauge needle
1 shown in the
points within the zone *
illustration.
The engine coolant temperature varies with
the outside air temperature and driving
conditions.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(89,1)
COMPASS (if so equipped)
CV37D1-D7D6A7D7-C213-459F-8AE8-616444F09CFF
preferably before the gauge reaches “0”.
There will be a small reserve of fuel in the
tank when the fuel gauge needle reaches
“0”.
The
indicates that the fuel-filler door is
located on the right side of the vehicle.
CAUTION
.
JVI0640X
FUEL GAUGE
CV37D1-B25CB842-078C-46AD-A9EB-B2F8CBAD9467
The gauge indicates the approximate fuel
level in the tank.
The gauge may move slightly during
braking, turning, acceleration, or going up
or down hills.
.
If the vehicle runs out of fuel, the
malfunction indicator light (MIL) may
come on. Refuel as soon as possible.
After a few driving trips, the
light
should turn off. If the light remains on
after a few driving trips, have the vehicle
inspected. It is recommended you visit
an INFINITI retailer for this service.
SIC3181
When the ignition switch is pushed to the
B will
ON position, the compass display *
indicate the direction of the vehicle’s
heading.
For additional information, see “Malfunction Indicator Light (MIL)” (P.2-19).
The gauge needle returns to “0” (Empty)
after the ignition switch is placed in the
OFF position.
Refill the fuel tank before the gauge
registers “0” (Empty).
NOS1741
If the display reads “C”, calibrate the
compass by driving the vehicle in 3
complete circles at less than 5 MPH (8
The low fuel warning light
illuminates
on the meter when the fuel level is getting
low. Refuel as soon as it is convenient,
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(90,1)
km/h). You can also calibrate the compass
by driving your vehicle on your everyday
route. The compass will be calibrated once
it has tracked 3 complete circles.
To turn on and off the compass manually,
A while the ignition
push the
switch *
switch is in the ON position.
SIC0611B
Zone map
2-10 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(91,1)
(The compass returns to the correct
compass point when the vehicle
moves to an area where the geomagnetism is stabilized.)
ZONE VARIATION CHANGE PROCEDURE
CV37D1-BB9F3440-D66E-4410-B16F-0EA5D87BF77F
The difference between magnetic north
and geographical north is known as
variance. In some areas, this difference
can sometimes be great enough to cause
false compass readings. Follow these
instructions to set the variance for your
particular location if this happens:
1. Push the
switch for more than 3
seconds. The current zone number will
appear in the display.
2. Find your current location and variance
number on the zone map.
3. Push the
switch repeatedly until
the new zone number appears in the
display, then release the switch. After
you release the switch, the display will
show a compass direction within a few
seconds.
. If the compass deviates from the
correct indication soon after repeated adjustment, it is recommended you have the compass
checked at an INFINITI retailer.
. The compass may not indicate the
correct compass point in tunnels or
while driving up or down a steep hill.
CAUTION
.
Do not install a ski rack, antenna, etc.,
which are attached to the vehicle by
means of a magnet. They affect the
operation of the compass.
.
When cleaning the mirror, use a paper
towel or similar material dampened with
glass cleaner. Do not spray glass cleaner
directly on the mirror as it may cause the
liquid cleaner to enter the mirror housing.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(92,1)
WARNING LIGHTS, INDICATOR LIGHTS AND
AUDIBLE REMINDERS
CV37D1-27260C9A-9A53-466E-ACF0-E491D66BB7DC
Power steering warning light
High beam assist indicator light (if so
equipped)
Seat belt warning light and chime
High beam indicator light
Supplemental air bag warning light
Idling Stop System indicator light (if so
equipped)
Charge warning light
Vehicle Dynamic Control (VDC) warning light
Malfunction Indicator Light (MIL)
Forward Emergency Braking (FEB) system
warning light (if so equipped)
ECO drive indicator light (if so equipped)
Security indicator light
Low fuel warning light
Exterior light indicator
Turn signal/hazard indicator lights
Low tire pressure warning light
Front fog light indicator light
Vehicle Dynamic Control (VDC) off indicator
light
Master warning light
Front passenger air bag status light
Anti-lock Braking System (ABS) warning
light
Brake warning light
CHECKINGCV37D1-AAEEDCA0-B409-469E-9994-4005AFDC3266
LIGHTS
With all doors closed, apply the parking
brake, fasten the seat belts and place the
ignition switch in the ON position without
starting the engine. The following lights (if
so equipped) will come on:
,
or
,
,
,
The following lights (if so equipped) will
come on briefly and then go off:
,
or
,
,
,
a burned-out bulb and/or a system malfunction. It is recommended you have the
system checked by an INFINITI retailer.
Some indicators and warnings are also
displayed in the vehicle information display between the speedometer and tachometer. (See “Vehicle information display”
(P.2-21).)
,
WARNING CV37D1-E4342973-71E9-450C-94D9-9EA3FA5505E2
LIGHTS
or
Anti-lock Braking
System (ABS)
warning light
CV37D1-BEE15A76-E254-45AA-8D27-5170CF592A69
When the ignition switch is in the ON
position, the Anti-lock Braking System
(ABS) warning light illuminates and then
turns off. This indicates the ABS is operational.
If the ABS warning light illuminates while
the engine is running, or while driving, it
may indicate the ABS is not functioning
properly. Have the system checked. It is
If any light does not come on or operates in
a way other than described, it may indicate
2-12 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(93,1)
recommended you visit an INFINITI retailer
for this service.
If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system
then operates normally, but without antilock assistance. (See “Brake system” (P.5133).)
or
Brake warning light
CV37D1-27E62D81-74AA-402A-ADDC-A48DD1FF9DA9
This light functions for both the parking
brake and the foot brake systems.
Parking brake
indicator:
CV37D1-25E41371-4A50-4503-A31C-DF021B7E2A39
When the ignition switch is in the ON
position, the light comes on when the
parking brake is applied.
Low brake fluid
warning light:
CV37D1-02E9B92A-54F8-4185-96F2-B812F36D0A38
When the ignition switch is in the ON
position, the light warns of a low brake
fluid level. If the light comes on while the
engine is running with the parking brake
not applied, stop the vehicle and perform
the following:
1. Check the brake fluid level. If brake
fluid is necessary, add fluid and have
the system checked. It is recommended
you have this service performed by an
INFINITI retailer. (See “Brake fluid” (P.8-
15).)
.
Pressing the brake pedal with the engine
stopped and/or low brake fluid level may
increase your stopping distance and
braking will require greater pedal effort
as well as pedal travel.
.
If the brake fluid level is below the
minimum or MIN mark on the brake fluid
reservoir, do not drive until the brake
system has been checked. It is recommended you visit an INFINITI retailer for
this service.
2. If the brake fluid level is correct, have
the warning system checked. It is
recommended you have this service
performed by an INFINITI retailer.
Anti-lock Braking System (ABS) warning
indicator: CV37D1-BC1A189C-21A9-40B4-B7B6-AF254F40E479
When the parking brake is released and
the brake fluid level is sufficient, if both the
brake warning light and the Anti-lock
Braking System (ABS) warning light illuminate, it may indicate the ABS is not
functioning properly. Have the brake system checked, and if necessary repaired. It
is recommended you visit an INFINITI
retailer for this service. (See “Anti-lock
Braking System (ABS) warning light” (P.212).)
WARNING
.
Your brake system may not be working
properly if the warning light is on.
Driving could be dangerous. If you judge
it to be safe, drive carefully to the
nearest service station for repairs.
Otherwise, have your vehicle towed
because driving it could be dangerous.
Charge
warning light
CV37D1-DEE104B8-D716-40F8-9978-636495B1465A
If the light comes on while the engine is
running, it may indicate the charging
system is not functioning properly. Turn
the engine off and check the alternator
belt. If the belt is loose, broken, missing or
if the light remains on, have your vehicle
serviced immediately. It is recommended
you visit an INFINITI retailer for this service.
CAUTION
Do not continue driving if the alternator belt
is loose, broken or missing.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(94,1)
Forward Emergency Braking
(FEB) system warning light (if so
equipped)CV37D1-95F33A94-5CB8-47CA-974E-13A974D0FC26
This light comes on when the ignition
switch is placed in the ON position. It turns
off after the engine is started.
This light illuminates when the FEB system
is set to OFF on the lower display.
If the light illuminates when the FEB
system is ON, it may indicate that the
system is unavailable. See “Forward Emergency Braking (FEB) system” (P.5-107) for
more details.
Low CV37D1-0AE22F4A-93A0-4332-B89F-BC8CB5973BB1
fuel warning light
This light illuminates when the fuel in the
tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel
gauge reaches the 0 (empty) position.
There will be a small reserve of fuel
remaining in the tank when the fuel gauge
reaches the 0 position.
light
Low tire pressure warning
CV37D1-30DE359F-7311-407E-AF3E-5C53309F6AED
Your vehicle is equipped with a Tire
Pressure Monitoring System (TPMS) that
monitors the tire pressure of all tires
except the spare tire (if so equipped).
The low tire pressure warning light warns
of low tire pressure and flat tire (if so
equipped) or indicates that the TPMS is not
functioning properly.
After the ignition switch is placed in the ON
position, this light illuminates for about 1
second and turns off.
Low tire pressure
warning:
CV37D1-1F58CF99-02B7-454C-9534-7FEF8D07D282
If the vehicle is being driven with low tire
pressure, the warning light will illuminate.
The “Tire Pressure Low - Add Air” warning
also appears in the vehicle information
display.
When the low tire pressure warning light
illuminates, you should stop and adjust the
tire pressure to the recommended COLD
tire pressure shown on the Tire and
Loading Information label. The low tire
pressure warning light does not automatically turn off when the tire pressure is
adjusted. After the tire is inflated to the
recommended pressure, the vehicle must
be driven at speeds above 16 MPH (25
km/h) to activate the TPMS and turn off the
low tire pressure warning light. Use a tire
pressure gauge to check the tire pressure.
The “Tire Pressure Low - Add Air” warning
is active as long as the low tire pressure
warning light remains illuminated.
For additional information, see “Vehicle
information display” (P.2-21), “Tire Pressure Monitoring System (TPMS)” (P.5-5)
and “Tire Pressure Monitoring System
(TPMS)” (P.6-3).
Flat tire warning
(if so equipped):
CV37D1-33E3CC75-9227-43CE-947F-5D6DBF52BE93
The flat tire warning warns of a flat tire.
If the vehicle is being driven with one or
more flat tires, the low tire pressure
warning light will illuminate continuously
and a chime will sound for 10 seconds. A
“Flat Tire - Visit dealer” warning also
appears in the vehicle information display.
The chime will only sound at the first
indication of a flat tire and the warning
light will illuminate continuously. When the
flat tire warning is activated, it is recommended you have the system reset and the
tire checked, and replaced if necessary, by
an INFINITI retailer. Even if the tire is
inflated to the specified COLD tire pressure, the warning light will continue to
illuminate until the system is reset.
Your vehicle can be driven for a limited
time on a flat tire. See “Run-flat tires” (P.6-
2-14 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(95,1)
4).
could lead to an accident and personal
injury. Also, driving a long distance at
high speeds may damage the tires.
tailer for this service.
TPMS malfunction:
CV37D1-56184CED-B10B-45B1-A679-C9C74898B0B9
If the TPMS is not functioning properly, the
low tire pressure warning light will flash for
approximately 1 minute when the ignition
switch is placed in the ON position. The
light will remain on after the 1 minute.
Have the system checked. It is recommended you visit an INFINITI retailer for
this service. The “Tire Pressure Low - Add
Air” warning does not appear if the low tire
pressure warning light illuminates to indicate a TPMS malfunction.
.
For additional information, see “Tire Pressure Monitoring System (TPMS)” (P.5-5).
WARNING
.
Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufacturer for the possible influences before
use.
.
If the light does not illuminate with the
ignition switch pushed ON, have the
vehicle checked as soon as possible. It is
recommended you visit an INFINITI re-
.
If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle speed,
pull off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and increase the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and could
result in serious personal injury. Check
the tire pressure for all four tires. Adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire and
Loading Information label to turn the low
tire pressure warning light OFF. If the
light still illuminates while driving after
adjusting the tire pressure, a tire may be
flat or the TPMS may be malfunctioning.
If you have a flat tire, replace it with a
spare tire (if so equipped) as soon as
possible. If no tire is flat and all tires are
properly inflated, it is recommended you
consult an INFINITI retailer.
For models with run-flat tires, although
you can continue driving with a punctured run-flat tire, remember that vehicle
handling stability is reduced, which
— Do not drive at speeds above 50
MPH (80 km/h) and do not drive more
than approximately 93 miles (150
km) with a punctured run-flat tire.
The actual distance the vehicle can
be driven on a flat tire depends on
outside temperature, vehicle load,
road conditions and other factors.
— If you detect any unusual sounds or
vibrations while driving with a punctured run-flat tire, pull off the road to
a safe location and stop the vehicle
as soon as possible. The tire may be
seriously damaged and need to be
replaced.
.
Since the spare tire is not equipped with
the TPMS, when a spare tire is mounted
or a wheel is replaced, the TPMS will not
function and the low tire pressure warning light will flash for approximately 1
minute. The light will remain on after the
1 minute. Have your tires replaced and/
or TPMS system reset as soon as
possible. It is recommended you visit
an INFINITI retailer for these services.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(96,1)
.
Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
CAUTION
.
The TPMS is not a substitute for the
regular tire pressure check. Be sure to
check the tire pressure regularly.
.
If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS
may not operate correctly.
.
Be sure to install the specified size of
tires to the four wheels correctly.
Master
warning light
CV37D1-78BF4531-FAEA-4D07-AD58-77A28662DD7C
When the ignition switch is in the ON
position, the master warning light illuminates if any of the following warnings
appear in the vehicle information display:
.
.
.
.
No key warning
PUSH warning
Key ID Incorrect warning
Low washer fluid warning
Door/trunk open warning
Loose fuel cap warning
Tire Pressure Low - Add Air warning
Flat Tire - Visit dealer warning (if so
equipped)
. All-Wheel Drive (AWD) warning (if so
equipped)
. Adaptive Front lighting System (AFS)
warning (if so equipped)
. Intelligent Key system warning
. Chassis control warning
. Parking brake release warning
. SHIFT “P” warning
. Low oil pressure warning
See “Vehicle information display” (P.2-21).
.
.
.
.
If the driver assist system warnings appear
in the vehicle information display, the
master warning light also illuminates. See
“Lane Departure Warning (LDW) system/
Lane Departure Prevention (LDP)” (P.5-35),
“Blind Spot Warning (BSW)” (P.5-42),
“Blind Spot Intervention® (BSI)” (P.5-50),
“Back-up Collision Intervention (BCI)” (P.563), “Distance Control Assist (DCA)” (P.596), “Forward Emergency Braking (FEB)
system” (P.5-107) and “Predictive Forward
Collision Warning (PFCW)” (P.5-116).
Power
steering warning light
CV37D1-F220FF51-D686-4A33-B641-63676E5BB4CA
Models withCV37D1-6C4247F4-E24D-44F7-A7D1-5FB0A28DEF8A
Direct Adaptive Steering :
When the ignition switch is in the ON
position, the power steering warning light
illuminates. After starting the engine, the
power steering warning light stays on for a
few seconds and turns off. This indicates
that Direct Adaptive Steering is operational. Drive the vehicle after the power
steering warning light turns off.
If the power steering warning light illuminates while driving, pull off the road to a
safe location and stop the vehicle. If the
power steering warning light turns off, you
can drive again. If the power steering
warning light continues to illuminate, it is
recommended you have Direct Adaptive
Steering checked by an INFINITI retailer.
(See “Direct Adaptive Steering type” (P.5131).)
Models with hydraulic pump electric
power steering
:
CV37D1-414BEBA6-F692-4D58-9A80-DCD93D9F2D89
When the ignition switch is in the ON
position, the power steering warning light
illuminates. After starting the engine, the
power steering warning light turns off. This
indicates that or hydraulic pump electric
power steering is operational.
2-16 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(97,1)
If the power steering warning light illuminates while the engine is running, it may
indicate hydraulic pump electric power
steering is not functioning properly and
may need servicing. It is recommended you
have the hydraulic pump electric power
steering checked by an INFINITI retailer.
(See “Hydraulic pump electric power steering type” (P.5-131).)
Models with
electric power steering :
CV37D1-EADBC1FD-69C3-4895-B2DD-2A1F7BB14AD3
When the ignition switch is in the ON
position, the power steering warning light
illuminates. After starting the engine, the
power steering warning light turns off. This
indicates the electric power steering is
operational.
If the power steering warning light illuminates while the engine is running, it may
indicate the electric power steering is not
functioning properly and may need servicing. It is recommended you have the
electric power steering checked by an
INFINITI retailer.
When the power steering warning light
illuminates with the engine running, the
power assist to the steering will cease
operation but you will still have control of
the vehicle. At this time, greater steering
efforts are required to operate the steering
wheel, especially in sharp turns and at low
speeds.
See “Electric power steering type” (P.5130).
Seat belt warning light and
chime CV37D1-B1CC9C1B-BD83-487A-A7F6-3428ECEC0077
The light and chime remind you to fasten
seat belts. The light illuminates whenever
the ignition switch is pushed to the ON
position, and will remain illuminated until
the driver’s seat belt is fastened. At the
same time, the chime will sound for about
6 seconds unless the driver’s seat belt is
securely fastened.
The seat belt warning light for the front
passenger will illuminate if the seat belt is
not fastened when the front passenger’s
seat is occupied.
See “Seat belts” (P.1-11) for precautions
on seat belt usage.
light
Supplemental air bag warning
seconds if the supplemental front air bag
and supplemental side air bag, curtain
side-impact air bag systems and/or pretensioner seat belt are operational.
If any of the following conditions occur, the
supplemental front air bag, supplemental
side air bag, supplemental curtain sideimpact air bag and pretensioner seat belt
needs servicing.
. The supplemental air bag warning light
remains on after approximately 7 seconds.
. The supplemental air bag warning light
flashes intermittently.
. The supplemental air bag warning light
does not come on at all.
It is recommended you visit an INFINITI
retailer for these services.
Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioner seat belt may not function
properly.
For additional information, see “Supplemental restraint system” (P.1-40).
CV37D1-028E75F0-7F8E-46E3-B980-53F7C9164FBD
After pushing the ignition switch to the ON
position, the supplemental air bag warning
light will illuminate. The supplemental air
bag warning light will turn off after about 7
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(98,1)
WARNING
If the supplemental air bag warning light is
on, it could mean that the supplemental
front air bag, supplemental side air bag,
curtain side-impact air bag systems and/or
pretensioner seat belt will not operate in an
accident. To help avoid injury to yourself or
others, have your vehicle checked. It is
recommended you visit an INFINITI retailer
for this service.
Vehicle Dynamic Control (VDC)
warning light
CV37D1-C0AA7A1A-7629-49A7-89B8-6292243BC6FA
When the ignition switch is in the ON
position, the Vehicle Dynamic Control
(VDC) warning light illuminates and then
turns off.
The light will blink when the VDC system or
the traction control system is operating,
thus alerting the driver that the vehicle is
nearing its traction limits. The road surface
may be slippery.
When the VDC warning light illuminates
when the VDC system is turned on, this
light alerts the driver to the fact that the
VDC system’s fail-safe mode is operating,
for example the VDC, active trace control
function, Brake Force Distribution or hill
start assist system may not be functioning
properly. Have the system checked. It is
recommended you visit an INFINITI retailer
for this service. If a malfunction occurs in
the system, the VDC system function will
be canceled but the vehicle is still driveable. For additional information, see “Vehicle Dynamic Control (VDC) system” (P.5136).
INDICATOR
LIGHTS
CV37D1-756E256E-AAC8-4DFC-B523-5734358B5B43
ECO drive indicator light (if so
equipped)
CV37D1-AC745CB7-7DA9-4BDF-B68A-C7496057B8CD
When the ignition switch is placed in the
ON position, the light will come on and
then turn off.
When the INFINITI Drive Mode Selector is
turned to the ECO mode, the ECO drive
indicator light will illuminate, blink or
remain off depending on the accelerator
pedal operation to help assist the driver to
drive economically. For more details, see
“ECO mode” (P.5-24).
Exterior
light indicator
CV37D1-007EC214-0CA9-4F5C-9C0E-66B22D543F4A
This indicator illuminates when the headlight switch is turned to the AUTO,
or
position and the exterior lights (such
as front parking lights, headlights, etc.) are
on. The indicator turns off when these
lights are turned off.
FrontCV37D1-F44E86A5-3DE4-4396-AE5B-7D3D962F82B0
fog light indicator light
The front fog light indicator light illuminates when the front fog lights are on. (See
“Fog light switch” (P.2-47).)
light
Front passenger air bag status
CV37D1-B5550EDA-03BC-41BA-8B43-3CDDA9789CEA
The front passenger air bag status light
(
) located on the instrument panel will
be lit and the passenger front air bag will
be OFF depending on how the front
passenger seat is being used.
For front passenger air bag status light
operation, see “INFINITI Advanced Air Bag
System (front seats)” (P.1-46).
2-18 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(99,1)
High beam assist indicator
light (if soCV37D1-3F4042C7-108D-4363-93CB-2BF070D132F4
equipped)
The indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beam selected. This indicates that the high
beam assist system is operational. (See
“High beam assist” (P.2-42).)
HighCV37D1-CFCB3FB3-DC4F-4572-AFDF-7DC4BD932014
beam indicator light
This light comes on when the headlight
high beam is on and goes out when the low
beam is selected.
Idling Stop System indicator
light (if soCV37D1-323942AC-6B83-4A54-82FF-E0A7BC154EF2
equipped)
The Idling Stop System indicator light
illuminates when the Idling Stop System
is activated.
The Idling Stop System indicator light
blinks at a high speed, when the engine
hood is open while the engine is stopped
by the system.
The Idling Stop System indicator light
blinks at a low speed, when the Idling
Stop System is malfunctioning.
NOTE:
. When the Idling Stop System indicator
light blinks at a high speed (twice
approximately every 1 second), be sure
to close the engine hood. When the
engine hood is open, the engine will be
in the normal stopped state. In this
case, restart the engine using the
ignition switch.
. When the Idling Stop System indicator
light blinks at a low speed (once
approximately every 1 second), it is
recommended you have the system
checked, and if necessary repaired, by
an INFINITI retailer promptly.
(MIL)
Malfunction Indicator Light
CV37D1-5EB179EE-ACAB-4F8B-B435-E99A0A72924E
If the malfunction indicator light comes on
steady or blinks while the engine is
running, it may indicate a potential emission control malfunction.
The malfunction indicator light may also
come on steady if the fuel-filler cap is loose
or missing, or if the vehicle runs out of fuel.
Check to make sure the fuel-filler cap is
installed and closed tightly, and that the
vehicle has at least 3 US gallons (11.4
liters) of fuel in the fuel tank.
After a few driving trips, the
light
should turn off if no other potential
emission control system malfunction exists.
If this indicator light remains on for 20
seconds and then blinks for 10 seconds
when the engine is not running, it indicates
that the vehicle is not ready for an
emission control system inspection/maintenance test. (See “Readiness for Inspection/Maintenance (I/M) test (US only)”
(P.10-22).)
Operation: CV37D1-2E89CD97-8BAB-4B9C-9C0A-62F224C54B9E
The malfunction indicator light will come
on in one of two ways:
. Malfunction indicator light on steady —
An emission control system malfunction has been detected. Check the fuelfiller cap if the Loose Fuel Cap warning
appears in the vehicle information display. If the fuel-filler cap is loose or
missing, tighten or install the cap and
continue to drive the vehicle. The
light should turn off after a few driving
trips. If the
light does not turn off
after a few driving trips, have the
vehicle inspected. It is recommended
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(100,1)
you visit an INFINITI retailer for this
service. You do not need to have your
vehicle towed to the retailer.
. Malfunction indicator light blinking —
An engine misfire has been detected
which may damage the emission control system.
To reduce or avoid emission control
system damage:
1) Do not drive at speeds above 45
MPH (72 km/h).
2) Avoid hard acceleration or deceleration.
3) Avoid steep uphill grades.
4) If possible, reduce the amount of
cargo being hauled or towed.
The malfunction indicator light may
stop blinking and remain on.
Have the vehicle inspected. It is recommended you visit an INFINITI retailer for this service. You do not need to
have your vehicle towed to the retailer.
CAUTION
Continued vehicle operation without having
the emission control system checked and
repaired as necessary could lead to poor
driveability, reduced fuel economy, and
possible damage to the emission control
system.
is pushed to OFF. This indicates that the
VDC system and traction control system
are not operating.
AUDIBLE REMINDERS
CV37D1-3AA97528-2B0C-424D-9825-53B4E0DF87EC
Security
indicator light
CV37D1-8635F0ED-0D0D-4E28-95C0-B27FBF6F6EDB
The light blinks when the ignition switch is
in the ACC, OFF or LOCK position. This
function indicates the security system
equipped on the vehicle is operational.
If the security system is malfunctioning,
this light will remain on while the ignition
switch is in the ON position. For additional
information, see “Security systems” (P.234).
Turn signal/hazard indicator
lights
CV37D1-10692ED4-BF78-4A36-BB9C-69C6F64C78C4
The light flashes when the turn signal
switch lever or hazard switch is turned on.
Vehicle Dynamic Control (VDC)
off indicator
light
CV37D1-8CC0C384-2200-42D1-96F4-B39EB909E790
When the ignition switch is placed in the
ON position, the light will come on and
then turn off.
Key reminder
chime
CV37D1-3432BABC-6F40-4EB7-AF2E-546928B397CB
A chime will sound if the driver side door is
opened while the ignition switch is pushed
to the ACC position. Make sure the ignition
switch is pushed to the OFF position, and
take the Intelligent Key with you when
leaving the vehicle.
Light reminder
chime
CV37D1-C5A86822-A3C4-4AAE-BD1F-AF8A1BC20396
A chime will sound when the driver side
door is opened with the light switch in the
or
position and the ignition switch
in the ACC, OFF or LOCK position.
Turn the light switch off when you leave the
vehicle.
Parking brake
reminder chime
CV37D1-08F79576-EAC7-4A14-A43E-BBC2FF17FDE3
The parking brake reminder chime will
sound if the vehicle is driven at more than
4 MPH (7 km/h) with the parking brake
applied. Stop the vehicle and release the
parking brake.
The light comes on when the VDC off switch
2-20 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(101,1)
VEHICLE INFORMATION DISPLAY
CV37D1-1CE230A5-CF30-4B3A-A402-45EE3BF84811
Brake padCV37D1-5BF946D6-6498-47D2-8825-4B103B685194
wear warning
The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first occur
only when the brake pedal is depressed.
After more wear of the brake pad, the
sound will always be heard even if the
brake pedal is not depressed. Have the
brakes checked as soon as possible if the
warning sound is heard.
Idling Stop System reminder buzzer
(if so equipped)
CV37D1-1ECA5139-DEA6-43E8-B24D-4A37C632E917
The Idling Stop System reminder buzzer
will sound if the engine hood is opened
while the Idling Stop System is activated.
NOTE:
Be sure to close the engine hood. When
the engine hood is open, the engine will be
in the normal stopped state. In this case,
restart the engine with the ignition switch.
.
.
.
JVI0641X
1
The vehicle information display *
is
located between the tachometer and the
speedometer, and it displays the warnings
and information. The following items are
also displayed if the vehicle is equipped
with them:
. Automatic Transmission (AT)
— “Driving the vehicle” (P.5-16)
. All-Wheel Drive (AWD)
— “Intelligent All-Wheel Drive (AWD)”
(P.5-127)
. Cruise control
— “Cruise control” (P.5-74)
. Intelligent Cruise Control (ICC)
.
.
.
.
.
— “Intelligent Cruise Control (ICC)”
(P.5-76)
Active Lane Control
— “Active Lane Control” (P.5-27)
Lane Departure Warning (LDW)/Lane
Departure Prevention (LDP)
— “Lane Departure Warning (LDW) system/Lane Departure Prevention
(LDP)” (P.5-35)
Blind Spot Warning (BSW)
— “Blind Spot Warning (BSW)” (P.5-42)
Blind Spot Intervention® (BSI)
— “Blind Spot Intervention ® (BSI)”
(P.5-50)
Back-up Collision Intervention (BCI)
— “Back-up Collision Intervention
(BCI)” (P.5-63)
Distance Control Assist (DCA)
— “Distance Control Assist (DCA)” (P.596)
Forward Emergency Braking (FEB)
— “Forward Emergency Braking (FEB)
system” (P.5-107)
Predictive Forward Collision Warning
(PFCW)
— “Predictive Forward Collision Warning (PFCW)” (P.5-116)
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-21
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(102,1)
. Active trace control
— “Active trace control” (P.5-138)
. Intelligent Key system
— “Intelligent Key system” (P.3-6)
. Idling Stop System
— “Idling Stop System” (P.5-140)
2-22 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(103,1)
JVI1510X
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-23
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(104,1)
INDICATORS
FOR OPERATION
CV37D1-64909E7F-8C96-4E67-B3E1-6588D21079FB
(See “Troubleshooting guide” (P.3-15).)
1. Engine CV37D1-A88CA30F-9D2B-44F6-9328-D7C4F5F6F61E
start operation indicator
4. “PUSH”CV37D1-3341FC08-E770-4537-B5E3-AB7ACF1A086E
warning
This indicator appears when the shift lever
is in the P (Park) position.
This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed. You can start
the engine directly in any position of the
ignition switch.
This warning appears when the shift lever
is moved to the P (Park) position with the
ignition switch in the ACC position after the
SHIFT “P” warning appears.
To push the ignition switch to the OFF
position, perform the following procedure:
when the Intelligent Key System and
vehicle are not communicating normally.
If this indicator appears, touch the ignition
switch with the Intelligent Key while
depressing the brake pedal. (See “Intelligent Key battery discharge” (P.5-14).)
7. Remote engine start indicator (if
so equipped)
CV37D1-5F91AF9A-3A09-4072-8E39-923C00EFA249
. SHIFT “P” warning ? (Move the shift
lever to “P”) ? PUSH warning ? (Push
the ignition switch ? ignition switch
position is turned to ON) ? PUSH
warning ? (Push the ignition switch
? ignition switch position is turned to
OFF)
This indicator appears when the engine
has been started using the remote start
function. To start the vehicle, depress the
brake pedal and place the ignition switch
in the ON position.
See “Intelligent Key system” (P.3-6) for
more details.
5. Intelligent Key battery discharge
indicator CV37D1-10DAEEAD-9FC3-4942-82E3-9B4A53F13AE8
8. Key ID Incorrect
warning
CV37D1-1048347A-3391-4966-8AA2-5D3B83859A7D
3. SHIFT “P”
warning
CV37D1-A781E6D3-618F-498F-BC4D-3983287D1D01
This indicator appears when the Intelligent
Key battery is running out of power.
2. NO KEYCV37D1-796E92CE-2B32-4D77-9DD6-0EE555C64AB0
warning
The warning appears when the door is
closed with the Intelligent Key left outside
the vehicle and the ignition switch in the
ACC or ON position. Make sure that the
Intelligent Key is inside the vehicle.
This warning appears when the ignition
switch is pushed to stop the engine with
the shift lever in any position except the P
(Park) position.
If this warning appears, move the shift
lever to the P (Park) position or push the
ignition switch to the ON position.
An inside warning chime will also sound.
If this indicator appears, replace the
battery with a new one. (See “Intelligent
Key battery replacement” (P.8-28).)
6. Engine start operation for Intelligent KeyCV37D1-F558F0B2-E1D4-41C4-9263-962DF1A50AF4
system indicator
This indicator appears when the Intelligent
Key battery is running out of power and
For more details, see “Remote engine
start” (P.3-20).
This warning appears when the ignition
switch is pushed from the LOCK position
and the Intelligent Key cannot be recognized by the system. You cannot start the
engine with an unregistered key. Use the
registered Intelligent Key.
See “Intelligent Key system” (P.3-6).
9. ParkingCV37D1-D0E7A2F3-E58C-4AB1-956B-CF6828D72988
brake release warning
This warning appears when the vehicle
speed is above 4 MPH (7 km/h) and the
2-24 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(105,1)
parking brake is applied.
10. Low fuel
warning
CV37D1-6D57E440-020D-40C9-9287-22A41A142DF4
This warning appears when the fuel level in
the tank is getting low. Refuel as soon as it
is convenient, preferably before the fuel
gauge reaches the empty (0) position.
There is a small reserve of fuel remaining
in the tank when the fuel gauge reaches
the empty (0) position.
11. Low washer
fluid warning
CV37D1-DAF8A34C-EC8E-48A9-AECD-07C6E8A313A0
This warning appears when the washer
tank fluid is at a low level. Add washer fluid
as necessary. (See “Window washer fluid”
(P.8-16).)
12. Door/trunk
open warning
CV37D1-BF6F8B2B-DDFF-4626-ADE2-1576DA433ADA
This warning appears if any of the doors
and/or the trunk lid are open or not closed
securely. The vehicle icon indicates which
door or the trunk lid is open on the display.
13. Intelligent
Key system warning
CV37D1-79D8FCFE-AC5D-4549-B87A-A9130816EC7A
This warning appears if there is a malfunction in the Intelligent Key system.
If this warning appears while the engine is
stopped, the engine cannot be started. If
this warning appears while the engine is
running, the vehicle can be driven. How-
ever, it is recommended you contact an
INFINITI retailer for repair as soon as
possible.
14. LooseCV37D1-B3E2FCE0-A8B6-40C3-88CC-48178F73936C
Fuel Cap warning
This warning appears when the fuel-filler
cap is not tightened correctly after the
vehicle has been refueled. (See “Fuel-filler
cap” (P.3-26).)
15. Tire Pressure Low - Add Air
warning CV37D1-4C26253E-7E93-4751-9C8A-98247F5BCF66
This warning appears when the low tire
pressure warning light in the meter illuminates and low tire pressure is detected. The
warning appears each time the ignition
switch is placed in the ON position as long
as the low tire pressure warning light
remains illuminated. If this warning appears, stop the vehicle and adjust the
pressure to the recommended COLD tire
pressure shown on the Tire and Loading
Information label. (See “Low tire pressure
warning light” (P.2-14) and “Tire Pressure
Monitoring System (TPMS)” (P.5-5).)
16. Flat Tire - Visit dealer warning (if
so equipped)
CV37D1-EC2E9B22-C047-4CE2-AE7B-DFDA40A257C8
nates and one or more flat tires are
detected while driving. A chime also
sounds for approximately 10 seconds.
(See “Low tire pressure warning light”
(P.2-14) and “Tire Pressure Monitoring
System (TPMS)” (P.5-5).)
17. Low oil pressure warning (for
VR30DDTTCV37D1-002F7C6F-4172-45ED-9BCD-B681823650BA
engine models)
This warning appears if low engine oil
pressure is detected. If the warning
appears during normal driving, pull off
the road in a safe area, stop the engine
immediately and call an INFINITI retailer or
other authorized repair shop.
The low oil pressure warning is not
designed to indicate a low oil level. Use
the dipstick to check the oil level. (See
“Engine oil” (P.8-10).)
18. Low oil level warning (for 2.0L
turbo gasoline
engine models)
CV37D1-B2754B08-7934-4872-A166-D9968DB0D41D
This warning appears if low engine oil level
is detected. If this warning appears, check
the oil level using the dipstick. (See
“Engine oil” (P.8-10).)
This warning appears when the low tire
pressure warning light in the meter illumiInstruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-25
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(106,1)
CAUTION
The oil level should be checked regularly
using the engine oil dipstick. Operating with
an insufficient amount of oil can damage the
engine and such damage is not covered by
the warranty.
21. Adaptive Front lighting System
(AFS) warning
(if so equipped)
CV37D1-0021430A-345D-433D-8422-F99BABE61FFD
This warning appears when the Adaptive
Front lighting System (AFS) is not functioning properly. It is recommended you have
the system checked by an INFINITI retailer.
(See “Adaptive Front lighting System
(AFS)” (P.2-45).)
19. All-Wheel Drive (AWD) warning
(if so equipped)
CV37D1-ABBC7728-F6D7-4FB2-9037-A82C4F8E26BF
22. Power will turn off to save the
battery warning
CV37D1-539CD88B-909A-462F-9024-7059D7BC6BB5
This warning appears when the Intelligent
All-Wheel Drive (AWD) system is not
functioning properly while the engine is
running. The displayed message will vary
depending on the condition of the AWD
system malfunction. (See “Intelligent AllWheel Drive (AWD)” (P.5-127).)
23. Power turned off to save the
battery warning
CV37D1-E4348DCA-7270-472D-991E-8F4CC571A21B
20. Extended
storage fuse warning
CV37D1-D4F1602F-C171-4A2C-94AF-39500B2E4921
This warning may appear if the extended
storage fuse switch is not pushed in
(switched on). When this warning appears,
push in (switch on) the extended storage
fuse switch to turn off the warning. For
more information, see “Extended storage
fuse switch” (P.8-27).
This warning appears after a period of time
if the shift lever has not moved from the
“P” (Park) position with the ignition switch
in the ACC or ON position.
This warning appears after the ignition
switch is automatically turned OFF to save
the battery.
24. Light CV37D1-2C148D4F-D28B-4275-A866-2B46EEDC2F36
reminder warning
This warning appears when the driver side
door is opened with the headlight switch is
left ON and the ignition switch is placed in
the ACC, OFF or LOCK position. Place the
headlight switch to “OFF” or “AUTO”
position. For additional information, see
“Headlight and turn signal switch” (P.240).
25. “TIMER”
indicator
CV37D1-7DEBFF56-E102-4EAA-903C-9E6B1C5D84E4
This indicator appears when the set
“TIMER” indicator activates. You can set
the time for up to 6 hours. (See the Infiniti
InTouch Owner’s Manual.)
26. Low outside temperature warning
CV37D1-BF2E7BC6-70A6-4A07-B5D8-1C5551EE8C7B
This warning appears if the outside temperature is below 378F (38C). The warning
can be set not to be displayed. (See the
Infiniti InTouch Owner’s Manual.)
27. Chassis
control warning
CV37D1-06BA8BA5-14AB-452B-B38C-5FF13359CD67
This warning appears if Active Lane Control
(if so equipped), the active trace control
system and/or chassis control are not
functioning properly. It is recommended
you have the system checked by an INFINITI
retailer. (See “Active Lane Control” (P.527), “Active trace control” (P.5-138) and
“Chassis control” (P.5-140).)
2-26 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(107,1)
28. CruiseCV37D1-A8FF4CA5-9F3E-4DA0-B756-B293036E1D58
indicator
Models without Intelligent Cruise Control
(ICC) system:
CV37D1-96CBAE77-DD46-4CE1-B2AC-5C684ED37D32
This indicator shows the cruise control
system status. The status is shown by the
color.
See “Cruise control” (P.5-74) for details.
Models with Intelligent Cruise Control
(ICC) system:
CV37D1-A7861C6D-52BF-4690-92BF-C2E3F1DA6989
This indicator shows the conventional
(fixed speed) cruise control mode status.
The status is shown by the color.
See “Conventional (fixed speed) cruise
control mode” (P.5-92) for details.
29. Intelligent Cruise Control (ICC)
system ON indicator (if so
equipped)CV37D1-C2F7FE0A-7E25-4149-BCD3-F440AD0BB7AA
This indicator shows the Intelligent Cruise
Control (ICC) system status. The status is
shown by the color. (See “Intelligent Cruise
Control (ICC)” (P.5-76).)
30. Driver assist system indicator
(if so equipped)
CV37D1-149E14D8-AF12-4633-8451-87B4055F0BF4
Lane Departure Warning (LDW)
Lane Departure Prevention (LDP)
Blind Spot Warning (BSW)
Blind Spot Intervention® (BSI)
Distance Control Assist (DCA)
Forward Emergency Braking (FEB)
Predictive Forward Collision Warning
(PFCW)
For more details, see “Lane Departure
Warning (LDW) system/Lane Departure
Prevention (LDP)” (P.5-35), “Blind Spot
Warning (BSW)” (P.5-42), “Blind Spot
Intervention® (BSI)” (P.5-50), “Distance
Control Assist (DCA)” (P.5-96), “Forward
Emergency Braking (FEB) system” (P.5-107)
and “Predictive Forward Collision Warning
(PFCW)” (P.5-116).
.
.
.
.
.
.
.
The figure and color of this indicator will
change depending on the conditions of the
above systems. (In each section, the name
of this indicator is referred to as, “driver
assist system lane indicator”, “driver
assist system blind spot indicator” or
“driver assist system forward indicator”
depending on the systems.)
This indicator shows the status of the
following systems.
31. INFINITI Drive Mode Selector
indicator CV37D1-708B65D5-BF9B-4CC6-974F-860B039A7695
When a driving mode is selected using the
INFINITI Drive Mode Selector, the selected
mode indicator is displayed.
. PERSONAL
. SPORT
. SPORT+ (if so equipped)
. STANDARD
. ECO (if so equipped)
. SNOW
(See “INFINITI Drive Mode Selector” (P.523).)
32. Idling Stop System indicator (if
so equipped)
CV37D1-9BBD8D19-95A1-4DF8-86B9-1CBD7930202D
This indicator shows the Idling Stop
System status. See “Idling Stop System”
(P.5-140).
33. Automatic Transmission (AT)
position indicator
CV37D1-96FE5B8E-78D9-4CE6-88E5-B9EAA6A7165B
This indicator shows the automatic shift
position.
In the manual shift mode, when the
transmission does not shift to the selected
gear due to a transmission protection
mode, the AT position indicator will blink
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(108,1)
1. Engine oil and filter replacement
indicator CV37D1-3FDC45F3-82B3-4BBF-978D-9DECB9A2BBB8
and a chime will sound.
See “Automatic Transmission (AT)” (P.5-16)
for further details.
This indicator appears when the customer
set time comes for changing the engine oil
and filter. You can set or reset the distance
for changing the engine oil and filter.
2. Tire replacement
indicator
CV37D1-D043BFB0-376C-436B-9507-B122A946EB96
This indicator appears when the customer
set distance comes for replacing tires. You
can set or reset the distance for replacing
tires.
WARNING
JVI0681M
INDICATORS
FOR MAINTENANCE
CV37D1-52C16D2B-467B-4859-8546-2AD67E5E6337
For setting the indicators for maintenance,
see the Infiniti InTouch Owner’s Manual.
The tire replacement indicator is not a
substitute for regular tire checks, including
tire pressure checks. See “Changing wheels
and tires” (P.8-42). Many factors including
tire inflation, alignment, driving habits and
road conditions affect tire wear and when
tires should be replaced. Setting the tire
replacement indicator for a certain driving
distance does not mean your tires will last
that long. Use the tire replacement indicator
as a guide only and always perform regular
tire checks. Failure to perform regular tire
checks, including tire pressure checks could
result in tire failure. Serious vehicle damage
2-28 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(109,1)
could occur and may lead to a collision,
which could result in serious personal injury
or death.
3. Other CV37D1-48BC06A4-D7B7-44C2-8CA0-26DC6E7DAE1A
indicator
This indicator appears when the customer
set time comes for replacing items other
than the engine oil, oil filter and tires. You
can set or reset the distance for replacing
the items.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-29
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(110,1)
JVI1518X
2-30 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(111,1)
1. Distance to empty (dte — mile or
km)
CV37D1-96CC8C44-6C3B-4125-9862-3E975E79A58B
The distance to empty (dte) mode provides
you with an estimation of the distance that
can be driven before refueling. The dte is
constantly being calculated, based on the
amount of fuel in the fuel tank and the
actual fuel consumption.
The display is updated every 30 seconds.
JVI1484X
TRIP COMPUTER
CV37D1-60C3F5A2-6BAA-4891-AFF0-D074E28C94F7
Switches for the trip computer are located
on the right side of the steering wheel. To
operate the trip computer, push the
switches.
Each time the
or
switch is pushed,
the display will change.
The display items for trip computer are
changed on the lower display. For details,
see the Infiniti InTouch Owner’s Manual.
The dte mode includes a low range warning
feature. If the fuel level is low, the warning
is displayed on the screen.
When the fuel level drops even lower, the
dte display will change to “——”.
. If the amount of fuel added is small, the
display just before the ignition switch
is placed in the OFF position may
continue to be displayed.
. When driving uphill or rounding curves,
the fuel in the tank shifts, which may
momentarily change the display.
2. Average
speed (MPH or km/h)
CV37D1-E76FD0BD-61AA-45EA-956A-721B61D795C3
The average speed mode shows the
average vehicle speed since the last reset.
Resetting is done by pushing the
or
switch for longer than 1 second.
The first 30 seconds after a reset, the
display shows “——”.
3. Elapsed time and trip odometer
(mile or km)
CV37D1-60B95DAC-9BB7-4ECB-8D17-C9E90E882461
Elapsed time:
CV37D1-82E92DFF-C368-48E8-A572-FBC736E0E5BB
The elapsed time mode shows the time
since the last reset. Resetting is done by
pushing the
or
switch for longer
than 1 second. (The trip odometer is also
reset at the same time.)
Trip odometer:
CV37D1-6BB84037-5704-47B6-A0A4-5B05D648582E
The trip odometer mode shows the total
distance the vehicle has been driven since
the last reset. Resetting is done by pushing
the
or
switch for longer than 1
second. (The elapsed time is also reset at
the same time.)
4. Trip fuel saved and engine stop
time (if soCV37D1-573DF975-97FA-4EA8-862E-5C8061A4E7DB
equipped)
The trip fuel saved and engine stop time
(Idling Stop System) mode shows amount
of fuel saved and the engine stop time
since the time the ignition switch was
placed in the ON position.
. The estimated quantity of saved fuel
The display is updated every 30 seconds.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-31
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(112,1)
. The time that the engine has been
stopped for by the Idling Stop System
The fuel saved and engine stop time can be
reset by pushing the
or
switch for
longer than 1 second.
See “Idling Stop System” (P.5-140) for
more details.
5. Total fuel saved and engine stop
time (if so GUID-B259F266-2170-40E6-ACAB-7432684C16CC
equipped)
The total fuel saved and engine stop time
(Idling Stop System) mode shows amount
of fuel saved and the engine stop time
since the last reset.
. The estimated quantity of saved fuel
. The time that the engine has been
stopped for by the Idling Stop System
The fuel saved and engine stop time can be
reset by pushing the
or
switch for
longer than 1 second.
See “Idling Stop System” (P.5-140) for
more details.
6. Current fuel consumption and
average fuel consumption (MPG, l
(liter)/100CV37D1-9F26A159-1A8E-41A3-B3DA-2BDBDB913432
km or km/l)
8. Audio
Current fuelCV37D1-BA18011E-EEA3-47F2-8E5B-A137B812BA2C
consumption:
The current fuel consumption mode shows
the current fuel consumption.
For more details, see the Infiniti InTouch
Owner’s Manual.
Average fuel
consumption:
CV37D1-37C99BD5-79FA-46E9-AA2C-8AD386E97C10
The average fuel consumption mode shows
the average fuel consumption since the
last reset. Resetting is done by pushing the
or
switch for longer than 1 second.
The driving aids mode shows the operating
condition for the following systems.
The average fuel consumption is also reset
on the lower display. See the Infiniti
InTouch Owner’s Manual.
The display is updated every 30 seconds.
At about the first 1/3 mile (500 m) after a
reset, the display shows “——”.
7. Navigation
(if so equipped)
CV37D1-102E235B-732B-4284-9FD7-43F56E6C97E7
When the route guidance is set in the
navigation system, this item shows the
navigation route information.
For more details, see the Infiniti InTouch
Owner’s Manual.
CV37D1-D84E035B-2AFA-4531-BA63-D98E6BCA01EF
The audio mode shows the status of audio
information.
9. DrivingCV37D1-2E875A1E-618B-447D-AEC2-512950D04573
aids (if so equipped)
Lane Departure Warning (LDW)
Lane Departure Prevention (LDP)
Blind Spot Warning (BSW)
Blind Spot Intervention® (BSI)
Distance Control Assist (DCA)
Forward Emergency Braking (FEB)
Predictive Forward Collision Warning
(PFCW)
For more details, see “Lane Departure
Warning (LDW) system/Lane Departure
Prevention (LDP)” (P.5-35), “Blind Spot
Warning (BSW)” (P.5-42), “Blind Spot
Intervention® (BSI)” (P.5-50), “Distance
Control Assist (DCA)” (P.5-96), “Forward
Emergency Braking (FEB) system” (P.5-107)
and “Predictive Forward Collision Warning
(PFCW)” (P.5-116).
.
.
.
.
.
.
.
2-32 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(113,1)
10. Tire pressure
CV37D1-4F040C9D-408B-4E17-BA7B-061BE8CF5CDF
The tire pressure mode shows the pressure
of all four tires while the vehicle is driven.
When the “Tire Pressure Low - Add Air” or
“Flat Tire - Visit dealer” (if so equipped)
warning appears, the display can be
switched to the tire pressure mode by
pushing the
or
switch.
The tire pressure unit can be changed in
the [TPMS setting] under the [Settings]
menu on the lower display. (See the Infiniti
InTouch Owner’s Manual.)
NOTE:
After the ignition switch is placed in the
ON position, it may take a period of time
for the tire pressure to be displayed while
the vehicle is driven. Depending on the
radio wave circumstance, tire pressure
may not correctly be displayed.
11. Chassis
control
CV37D1-00A6F095-16DB-4675-8D5E-64ECA7EEA1DF
When Active Lane Control (if so equipped)
or the active trace control system is
operated, it shows the operating condition.
See “Active Lane Control” (P.5-27) and
“Active trace control” (P.5-138) for more
details.
12. Oil control system (for
VR30DDTT
engine models)
CV37D1-CB13F524-42DC-42CD-A6C6-AB8AEF15B75F
Engine oil information informs the distance
to oil change.
Warning check
CV37D1-84D17C85-7598-4143-B76A-A1BD37562223
The present warnings are displayed. If no
warning is present, “No Warning” is
displayed.
Distance to CV37D1-760A4A16-DFA7-4FE4-BD0D-8D3BDF6E1EF7
oil change:
The distance to oil change is displayed if
the distance to oil change comes to be less
than 940 miles (1,500 km).
Oil replacement
indicator:
CV37D1-094E2566-E820-4572-BD7B-5D333F5AFBEA
When the set mileage approaches, the
engine oil replacement indicator will appear on the display. After the oil is
changed, reset the oil control system by
pushing the
or
switch for longer
than 1 second.
The oil change interval cannot be adjusted
manually. The distance to oil change
interval is calculated depending on the
driving conditions and set automatically by
the oil control system.
CAUTION
If the oil replacement indicator is displayed,
change the engine oil as soon as possible.
Operating your vehicle with deteriorated oil
can damage the engine.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-33
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(114,1)
SECURITY SYSTEMS
CV37D1-3A21F676-5A6E-4477-B844-5B384A714C8C
The outside temperature sensor is located
in front of the radiator. The sensor may be
affected by road or engine heat, wind
directions and other driving conditions.
The display may differ from the actual
outside temperature or the temperature
displayed on various signs or billboards.
SIC2132
JVI0679M
Your vehicle has two types of security
systems, as follows:
CLOCK AND OUTSIDE AIR TEMPERATURECV37D1-5D517F72-5EA6-4DD3-883A-541FEA9805FD
. Vehicle security system
. INFINITI Vehicle Immobilizer System
The security condition will be shown by the
security indicator light.
1 and outside air temperature
The clock *
2 are displayed on the upper side of the
*
vehicle information display.
Clock
CV37D1-45493C10-3BA4-49EC-9DCE-41E4ED9EED08
The clock can be adjusted on the lower
display. See the Infiniti InTouch Owner’s
Manual.
Outside air
temperature (8F or 8C)
CV37D1-3D487D7F-28C9-4C29-B01D-77B8BCA6FE1E
The outside air temperature is displayed in
8F or 8C in the range of −22 to 1318F (−30 to
558C).
2-34 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(115,1)
VEHICLE SECURITY
SYSTEM
CV37D1-B2E64354-87F4-40F9-91AD-DA874CA2A588
The vehicle security system provides visual
and audio alarm signals if someone opens
the doors, hood, or trunk lid when the
system is armed. It is not, however, a
motion detection type system that activates when a vehicle is moved or when a
vibration occurs.
The system helps deter vehicle theft but
cannot prevent it, nor can it prevent the
theft of interior or exterior vehicle components in all situations. Always secure your
vehicle even if parking for a brief period.
Never leave your Intelligent Key(s) in the
vehicle, and always lock it when unattended. Be aware of your surroundings,
and park in secure, well-lit areas whenever
possible.
Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are
available at auto supply stores and specialty shops. Your INFINITI retailer may also
offer such equipment. Check with your
insurance company to see if you may be
eligible for discounts for various theft
protection features.
SIC2045
5. Confirm that the security indicator light
comes on. The security indicator light
stays on for about 30 seconds. The
vehicle security system is now prearmed. After about 30 seconds the
vehicle security system automatically
shifts into the armed phase. The
security light begins to flash once every
approximately 3 seconds. If, during this
30-second pre-arm time period, the
door is unlocked, or the ignition switch
is pushed to ACC or ON, the system will
not arm.
The system can be armed even if the
windows are open.
Even when the driver and/or passengers
are in the vehicle, the system will activate
with all doors, hood, and trunk lid locked
with the ignition switch in the LOCK
position. When pushing the ignition switch
to the ACC or ON position, the system will
be released.
2. Push the ignition switch to the OFF
position.
Vehicle security
system activation
CV37D1-3A452288-F884-4B4B-B1D6-D5997C1EA010
How to arm the vehicle security
system CV37D1-8ED55579-9B8D-449D-B4BE-9610F62444F0
1. Close all windows.
3. Remove the Intelligent Key from the
vehicle.
4. Close all doors, hood and trunk. Lock
all doors. The doors can be locked with
the Intelligent Key, door handle request
switch, power door lock switch or
mechanical key.
The vehicle security system will give the
following alarm:
. The headlights blink and the horn
sounds intermittently.
. The alarm automatically turns off after
approximately 1 minute. However, the
alarm reactivates if the vehicle is
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-35
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(116,1)
tampered with again.
The alarm is activated by:
. Unlocking the door or opening the trunk
lid without using the button on the
Intelligent Key, the door handle request
switch, one touch unlock sensor or the
mechanical key. (Even if the door is
opened by releasing the door inside
lock knob, the alarm will activate.)
. Opening the hood.
How to stop
an activated alarm
CV37D1-DF1E4DAC-68DF-4235-AD8F-E1909167B5F8
The alarm will stop by unlocking a door by
pushing the UNLOCK button on the Intelligent Key, the door handle request switch,
touching the one touch unlock sensor or
using the mechanical key. The alarm will
not stop if the ignition switch is placed in
the ACC or ON position.
If the system does not operate as described above, it is recommended you have
it checked by an INFINITI retailer.
INFINITI VEHICLE IMMOBILIZER
SYSTEM CV37D1-4C75AC83-8C74-453D-97A9-A911C41A3437
ference that may cause undesired operation of the device.
The INFINITI Vehicle Immobilizer System
will not allow the engine to start without
the use of the registered Intelligent Key.
Never leave these keys in the vehicle.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including inter-
2-36 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(117,1)
WIPER AND WASHER SWITCH
CV37D1-E0758907-1973-4985-986D-36DEFC06E1DA
INFINITI Vehicle Immobilizer System as
soon as possible. Please bring all registered keys that you have. It is recommended you visit an INFINITI retailer for
this service.
WARNING
In freezing temperatures the washer solution may freeze on the windshield and
obscure your vision which may lead to an
accident. Warm windshield with the defroster before you wash the windshield.
CAUTION
.
Security indicator
light
CV37D1-CDF2B03A-33CE-47EA-8D1E-DF796DD54E1A
Do not operate the washer continuously
for more than 30 seconds.
.
The security indicator light is located on
the meter panel. It indicates the status of
the INFINITI Vehicle Immobilizer System.
Do not operate the washer if the
reservoir tank is empty.
.
Do not fill the window washer reservoir
tank with washer fluid concentrates at
full strength. Some methyl alcohol
based washer fluid concentrates may
permanently stain the grille if spilled
while filling the window washer reservoir tank.
.
Pre-mix washer fluid concentrates with
water to the manufacturer’s recommended levels before pouring the fluid
into the window washer reservoir tank.
Do not use the window washer reservoir
SIC2045
The light blinks after the ignition switch
was in the LOCK, ACC or OFF position. This
function indicates the security systems
equipped on the vehicle are operational.
If the INFINITI Vehicle Immobilizer System
is malfunctioning, this light will remain on
while the ignition switch is in the ON
position.
If the light still remains on and/or the
engine will not start, seek service for the
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-37
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(118,1)
The windshield wiper and washer operates
when the ignition switch is in the ON
position.
tank to mix the washer fluid concentrate
and water.
JVI0737X
Type A (if so equipped)
JVI0738X
Type B (if so equipped)
Push the lever down to operate the wiper at
the following speed:
1
INT (Type A) (if so equipped) —
*
intermittent operation can be adA
justed by turning the knob toward *
B
(Slower) or *
(Faster). When the
speed sensing wiper interval function
is turned on, the intermittent operation speed varies in accordance with
the vehicle speed. (For example, when
the vehicle speed is high, the intermittent operation speed will be faster.) To turn this function on and off,
see the Infiniti InTouch Owner’s Manual.
1
AUTO (Type B) (if so equipped) — For
*
models with the rain-sensing auto
wiper system, see “Rain-sensing auto
wiper system” (P.2-39).
2
* LO — continuous low speed operation
3
HI — continuous high speed operation
*
4
MIST — one sweep operation of the
*
wiper
5 to operate the
Pull the lever toward you *
washer. Then the wiper will also operate
several times.
2-38 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(119,1)
Pulling up the wiper arm:
(High) or toward
The wiper arm should be in the up position
when replacing the wiper.
. High — High sensitive operation
. Low — Low sensitive operation
To turn the rain-sensing auto wiper system
off, push up the lever to the OFF position,
or pull down the lever to the LO or HI
position.
4 twice
To pull up the wiper arm, push up *
when the ignition switch is in the OFF
position within 1 minute. The wiper operation stops in mid-operation and the wiper
arm can be pulled up.
The shift lever should be in the P (Park)
position.
To return the wiper arm, place the wiper
arm in the down position and operate the
wiper switch once.
CAUTION
CAUTION
JVI0739X
RAIN-SENSING AUTO WIPER SYSTEM (if soCV37D1-18362D14-ED60-48EC-B451-A104BE5F6453
equipped)
Wiper drip wipe system:
The rain-sensing auto wiper system can
automatically turn on the wipers and adjust
the wiper speed depending on the rainfall
and the vehicle speed by using the rain
sensor located on the upper part of the
windshield.
The wiper will also operate once about 3
seconds after the washer and wiper are
operated. This operation is to wipe washer
fluid that has dripped on the windshield.
To set the rain-sensing auto wiper system,
push the lever down to the AUTO position
1 . The wiper will sweep once while the
*
ignition switch is in the ON position.
Do not operate the windshield wiper while
the wiper arm is pulled up. The wiper arm
may be damaged.
3 (Low).
*
The rain sensor sensitivity level can be
2
adjusted by turning the knob toward *
Do not touch the rain sensor and around it
when the wiper switch is in the AUTO
position and the ignition switch is in the
ON position. The wipers may operate unexpectedly and cause to an injury or may
damage a wiper.
. The rain-sensing auto wipers are intended for use during rain. If the switch
is left in the AUTO position, the wipers
may operate unexpectedly when dirt,
fingerprints, oil film or insects are
stuck on or around the sensor. The
wipers may also operate when exhaust
gas or moisture affect the rain sensor.
. The rain-sensing auto wipers may not
operate if rain does not hit the rain
sensor even if it is raining.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-39
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(120,1)
REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH
HEADLIGHT AND TURN SIGNAL SWITCH
CV37D1-E0A2D0C4-55C8-4F18-A2DE-1F96531D49A1
CV37D1-DC8AE445-0020-408E-A99C-1746C7FA278D
. When the windshield glass is coated
with water repellent, the speed of the
rain-sensing auto wipers may be higher even though the amount of the
rainfall is small.
. Be sure to turn off the rain-sensing auto
wiper system when you use a car wash.
. Using genuine wiper blades is recommended for proper operation of the
rain-sensing auto wiper system. (See
“Windshield wiper blades” (P.8-23) for
wiper blade replacement.)
JVI1441X
To defog/defrost the rear window glass
and outside mirrors, start the engine and
1 on. The indicator light
push the switch *
2 will come on. Push the switch again to
*
turn the defroster off.
JVI1485X
HEADLIGHT
SWITCH
CV37D1-A97D1787-5D60-49FB-97B0-C49E3C404EDC
Lighting
1
*
It will automatically turn off in approximately 15 minutes.
2
*
CAUTION
CV37D1-7FF0D9DF-3DE7-4696-9944-BB1F285007B0
Turn the switch to the
position:
The front parking, side marker, emblem (if so equipped), tail and license
plate lights will come on.
Turn the switch to the
position:
Headlights will come on and all the
other lights remain on.
When cleaning the inner side of the rear
window, be careful not to scratch or damage
the rear window defroster.
2-40 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(121,1)
The autolight system can turn on the
headlights automatically when it is dark
and turn off the headlights when it is light.
The headlights will turn on automatically at
twilight or in rainy weather (when the
windshield wiper is operated continuously).
If the ignition switch is placed in the OFF
position and one of the doors is opened
and this condition is continued, the headlights remain on for 5 minutes.
JVI1486X
Autolight CV37D1-6670CC80-46B2-4BB2-A7FE-53049C3FA3BE
system
The autolight system allows the headlights
to be set so they turn on and off
automatically.
To set the autolight system:
1. Make sure the headlight switch is in the
1 .
AUTO position *
2. Place the ignition switch in the ON
position.
Automatic headlights
off delay:
CV37D1-DD6AA237-F204-4898-A176-A84AC16A3B11
You can keep the headlights on for up to
180 seconds after you place the ignition
switch in the OFF position and open any
door then close all the doors.
You can adjust the period of the automatic
headlights off delay from 0 seconds (OFF)
to 180 seconds. The factory default setting
is 45 seconds.
SIC3784
Be sure not to put anything on top of the
1 located on the top of the
photo sensor *
instrument panel. The photo sensor controls the autolight; if it is covered, the
photo sensor reacts as if it is dark and the
headlights will illuminate.
For automatic headlights off delay setting,
see the Infiniti InTouch Owner’s Manual.
3. The autolight system automatically
turns the headlights on and off.
To turn the autolight system off, turn the
switch to the OFF,
or
position.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-41
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(122,1)
High beam
assist (if so equipped)
CV37D1-38075300-AA15-4284-84AF-CE1A9D143DC5
The high beam assist system will operate
when the vehicle is driven at speeds of
approximately 19 MPH (30 km/h) and
above. If an oncoming vehicle or leading
vehicle appears in front of your vehicle
when the headlight high beam is on, the
headlight will be switched to the low beam
automatically.
PrecautionsCV37D1-CE38A3BD-255D-4E3D-BB1D-D69A3E309132
on high beam assist:
WARNING
JVI1487X
HeadlightCV37D1-F70D9D7A-F42F-45D3-9507-557BBC6C84AE
beam select
1
*
2
*
3
*
To select the low beam, put the lever
in the neutral position as shown.
To select the high beam, push the
lever forward while the switch is in the
position. Pull it back to select the
low beam.
Pulling the lever toward you will flash
the headlight high beam even when
the headlight switch is in the OFF
position.
.
.
The high beam assist system is a
convenience but it is not a substitute
for safe driving operation. The driver
should remain alert at all times, ensure
safe driving practices and switch the
high beams and low beam manually
when necessary.
The high beam or low beam may not
switch automatically under the following
conditions. Switch the high beam and
low beam manually.
— During bad weather (rain, fog, snow,
wind, etc.).
— When a light source similar to a
headlight or tail light is in the
vicinity of the vehicle.
— When the headlights of the oncoming vehicle or the leading vehicle are
turned off, when the color of the light
is affected due to foreign materials
on the lights, or when the light beam
is out of position.
— When there is a sudden, continuous
change in brightness.
— When driving on a road that passes
over rolling hills, or a road that has
level differences.
— When driving on a road with many
curves.
— When a sign or mirror-like surface is
reflecting intense light towards the
front of the vehicle.
— When the container, etc. being
towed by a leading vehicle is reflecting intense light.
— When a headlight on your vehicle is
damaged or dirty.
— When the vehicle is leaning at an
angle due to a punctured tire, being
towed, etc.
2-42 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(123,1)
.
headlight remains the low beam.
The timing of switching the low beam
and high beam may change under the
following situations.
To turn off the high beam assist system,
turn the headlight switch to the
position or select the low beam position
by placing the lever in the neutral position.
— The brightness of the headlights of
the oncoming vehicle or leading
vehicle.
— The movement and direction of the
oncoming vehicle and the leading
vehicle.
— When only one light on the oncoming vehicle or the leading vehicle is
illuminated.
— When the oncoming vehicle or the
leading vehicle is a two-wheeled
vehicle.
— Road conditions (incline, curve, the
road surface, etc.).
— The number of passengers and the
amount of luggage.
JVI1488X
High beam CV37D1-AD2477C0-5AA1-445C-BD30-C04059847F2B
assist operations:
To activate the high beam assist system,
turn the headlight switch to the AUTO
1 and push the lever forward *
2
position *
(high beam position). The high beam assist
indicator light in the meter will illuminate
while the headlights are turned on.
If the high beam assist indicator light does
not illuminate in the above condition, it
may indicate that the system is not
functioning properly. It is recommended
you have the system checked by an INFINITI
retailer.
When the vehicle speed lowers to less than
approximately 12 MPH (20 km/h), the
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-43
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(124,1)
If the ambient image sensor is damaged
due to an accident, it is recommended you
contact an INFINITI retailer.
Battery saver
system
CV37D1-2545EC0C-F5FC-4D5B-A65F-0CBE6414EDA7
A chime will sound and the light reminder
warning will appear in the vehicle information display when the driver side door is
opened with the light switch in the
or
position and the ignition switch in the
ACC, OFF or LOCK position.
JVS0823X
Ambient image
sensor maintenance:
CV37D1-C5151859-1053-4B17-84C8-598801BD0D23
1 for the high
The ambient image sensor *
beam assist system is located above the
inside mirror. To keep the proper operation
of the high beam assist system and
prevent a system malfunction, be sure to
observe the following:
. Always keep the windshield clean.
. Do not attach a sticker (including
transparent material) or install an
accessory near the ambient image
sensor.
. Do not strike or damage the areas
around the ambient image sensor.
When the headlight switch is in the
or
position while the ignition switch is in
the ON position, the lights will automatically turn off after a period of time when
the ignition switch has been pushed to the
OFF position.
When the headlight switch remains in the
or
position after the lights automatically turn off, the lights will turn on
when the ignition switch is pushed to the
ON position.
CAUTION
.
the OFF position when you leave the
vehicle for extended periods of time,
otherwise the battery will be discharged.
.
Never leave the light switch on when the
engine is not running for a period of time
even if the headlights turn off automatically.
Daytime running
light system
CV37D1-96A89700-E692-4881-A9D1-74D83EDD550C
The daytime running lights automatically
illuminate when the engine is started with
the parking brake released. The daytime
running lights operate with the headlight
switch in the OFF, AUTO or
position.
Turn the headlight switch to the
position for full illumination when driving
at night.
If the parking brake is applied before the
engine is started, the daytime running
lights do not illuminate. The daytime
running lights illuminate once the parking
brake is released. The daytime running
lights will remain on until the ignition
switch is pushed to the OFF position.
When you turn on the headlight switch
again after the lights automatically turn
off, the lights will not turn off automatically. Be sure to turn the light switch to
2-44 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(125,1)
WARNING
When the daytime running light system is
active, tail lights on your vehicle are not on.
It is necessary at dusk to turn on your
headlights. Failure to do so could cause an
accident injuring yourself and others.
Adaptive Front lighting System
(AFS) (if soCV37D1-5CF3AE2B-E740-40B3-9176-1D2088411228
equipped)
The Adaptive Front lighting System (AFS)
will automatically adjust the headlights
(low beam) toward the turning direction to
improve the driver’s view. When the headlight switch is ON and the driver operates
the steering wheel in a turn, the AFS
system will be activated.
the steering wheel is turned.
AFS will also adjust the headlight to a
proper axis automatically, depending on
the number of occupants in the vehicle, the
load the vehicle is carrying and the road
conditions.
If the AFS warning appears in the vehicle
information display after the ignition
switch has been pushed to the ON position, this may indicate that the AFS is not
functioning properly. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service. When the
engine is started, the headlights will
vibrate to check the system condition. This
is not a malfunction.
JVI0644X
The AFS will operate:
. when the headlight switch is ON.
. when the shift lever is in any position
other than P (Park) or R (Reverse).
. when the vehicle is driven at above 3
MPH (5 km/h) for the left-side headlight. Note that the right-side low beam
headlight will swivel but the left-side
headlight will not swivel when the
vehicle is below 3 MPH (5 km/h) and
JVI0937X
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-45
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(126,1)
Instrument
brightness control
CV37D1-8EFD1E27-5505-471E-A11D-ADBE8B1FDF70
. Move the lever up or down until the turn
signal begins to flash, but the lever
does not latch, and release the lever.
The turn signal will automatically flash
three times.
Choose the appropriate method to signal a
lane change based on road and traffic
conditions.
The instrument brightness control switch
can be operated when the ignition switch is
in the ON position. When the switch is
operated, the vehicle information display
switches to the brightness adjustment
mode.
A
Push the + side of the switch *
to
brighten the instrument panel lights. The
1 moves to the + side.
bar *
B to dim the
Push the - side of the switch *
1 moves
instrument panel lights. The bar *
to the − side. When the brightness level
reaches the minimum, the instrument
panel lights will turn off during the nighttime.
When the brightness level reaches the
maximum or minimum, a beep will sound.
The vehicle information display returns to
the normal display when the instrument
brightness control switch is not operated
for more than 5 seconds.
JVI1489X
TURN SIGNAL
SWITCH
CV37D1-6122787A-8BE2-4BAE-BE63-A9E30B7A7A07
1 Turn signal
*
CV37D1-4E6F4533-6680-4995-B4E2-B3CE9D242130
Move the lever up or down to signal the
turning direction. When the turn is completed, the turn signals cancel automatically.
2 Lane change signal
*
CV37D1-9CBD8B3D-027A-4B76-813E-425FD896C905
. Move the lever up or down until the turn
signal begins to flash, but the lever
does not latch, to signal a lane change.
Hold the lever until the lane change is
completed.
2-46 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(127,1)
HORN
CV37D1-87CEAEB1-8B39-4156-9CAE-F0F804171559
JVI1491X
JVI1490X
FOG LIGHTCV37D1-0CD698F6-A977-4171-B7DD-C1E157896593
SWITCH
To turn the fog lights on, turn the headlight
switch to the
position, then turn the
switch to the
position. To turn them off,
turn the switch to the OFF position.
The headlights must be on with the low
beams selected for the fog lights to
operate. The fog lights automatically turn
off when the high beam headlights are
selected.
To sound the horn, push the center pad
area of the steering wheel.
WARNING
Do not disassemble the horn. Doing so could
affect proper operation of the supplemental
front air bag system. Tampering with the
supplemental front air bag system may
result in serious personal injury.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
CV37D1-3AEA4C41-CB09-4DCF-8036-823AE6B4A697
SIC4336
The vehicle should be driven with the
Vehicle Dynamic Control (VDC) system on
for most driving conditions.
If the vehicle is stuck in mud or snow, the
VDC system reduces the engine output to
reduce wheel spin. The engine speed will
be reduced even if the accelerator is
depressed to the floor. If maximum engine
power is needed to free a stuck vehicle,
turn the VDC system off.
To turn off the VDC system, push the VDC
OFF switch. The
indicator light will
illuminate.
Push the VDC OFF switch again or restart
the engine to turn on the system. (See
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-47
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(128,1)
HEATED SEATS (if so equipped)
CV37D1-E57CAE87-BC9D-4A04-8415-C2C0B200E402
“Vehicle Dynamic Control (VDC) system”
(P.5-136).)
WARNING
Do not use or allow occupants to use the
seat heater if you or the occupants cannot
monitor elevated seat temperatures or have
an inability to feel pain in those body parts
in contact with the seat. Use of the seat
heater by such people could result in
serious injury.
.
Any liquid spilled on the heated seat
should be removed immediately with a
dry cloth.
.
When cleaning the seat, never use
gasoline, thinner, or any similar materials.
.
If any malfunctions are found or the
heated seat does not operate, turn the
switch off and have the system checked.
It is recommended you visit an INFINITI
retailer for this service.
CAUTION
.
The battery could run down if the seat
heater is operated while the engine is
not running.
.
Do not use the seat heater for extended
periods or when no one is using the seat.
.
Do not put anything on the seat which
insulates heat, such as a blanket,
cushion, seat cover, etc. Otherwise, the
seat may become overheated.
.
Do not place anything hard or heavy on
the seat or pierce it with a pin or similar
object. This may result in damage to the
heater.
2-48 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(129,1)
HEATED STEERING WHEEL (if so equipped)
GUID-C8BDC5D1-23D1-4DA8-8AF3-B17C10CDC51F
When the vehicle’s interior is warmed, or
before you leave the vehicle, be sure to
turn off the seat heater.
OPERATIONGUID-DFA73E91-834C-499A-BA81-52F38576EA06
WITH TOUCH SCREEN
Push the CLIMATE button and touch [
]
or [
] on the lower display. Select an
item from [AUTO], [High], [Mid], [Low] or
[OFF].
AUTO MODEGUID-1D3F9C10-E1F1-44F1-B0C0-A9AA87867E26
SETTING
JVR0505X
The front seats can be warmed by built-in
heaters. The heating system of driver’s
seat and front passenger seat can be
operated independently.
OPERATIONGUID-DFEB6095-413C-4325-AB76-FFA5FABC076E
WITH SWITCH
When in the AUTO mode, the heater will
turn on or off automatically according to
the conditions such as the temperature
inside the vehicle compartment. Depending on the conditions, the heater will not
turn on even if AUTO is selected. The
settings for the AUTO mode can be
changed. For details, see the Infiniti
InTouch Owner’s Manual.
WARNING
Do not use or allow occupants to come into
contact with the heated steering wheel if
you or the occupants cannot monitor elevated steering wheel temperatures or have
an inability to feel pain in those body parts
in contact. Use of the heated steering wheel
by such people could result in serious
injuries.
CAUTION
.
The battery could run down if the
steering wheel heater is operated while
the engine is not running.
.
Do not use the steering wheel heater for
extended periods of time as it may cause
burns and overheating.
.
Any liquid spilled on the steering wheel
should be removed immediately with a
dry cloth.
.
When cleaning the steering wheel, never
use gasoline, thinner, or any similar
materials.
1. Start the engine.
2. Push the switch on the instrument
panel.
. Each time the switch is pushed, the
seat heating mode will change in the
following order.
AUTO ? High ? Mid ? Low ? OFF
. The indicator light *
1 on the switch
will illuminate when the heater is on.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-49
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(130,1)
POWER OUTLETS
CV37D1-42C176E4-70E1-482B-AA1F-4C9A9B43B7C4
.
The power outlets are located in the
storage box and in the console box.
If any malfunctions are found or the
steering wheel heater does not operate,
turn the switch off. It is recommended
that you have the system checked by an
INFINITI retailer.
Push the CLIMATE button and touch [Steering Heater] on the lower display to turn on
or off the steering wheel heating manually.
The steering wheel heating will turn off
automatically 30 minutes after it has been
turned on. When the steering wheel heating is turned on, the indicator above
[Steering Heater] will turn on.
If the surface temperature of the steering
wheel is above the temperature within
which the system is designed to operate,
the system will not heat the steering
wheel. This is not a malfunction.
CAUTION
SIC4316
.
The outlet and plug may be hot during or
immediately after use.
.
Do not use with accessories that exceed
a 12 volt, 120W (10A) power draw. Do
not use double adapters or more than
one electrical accessory.
.
Use power outlet with the engine running to avoid discharging the vehicle
battery.
.
Avoid using power outlet when the air
conditioner, headlights or rear window
defroster is on.
.
This power outlet is not designed for use
with a cigarette lighter unit.
.
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may blow.
.
Before inserting or disconnecting a plug,
be sure the electrical accessory being
used is turned OFF.
In the storage box
Automatic steering wheel heating can be
turned on or off from the climate control
settings screen. For details, see the Infiniti
InTouch Owner’s Manual.
JVI1298X
In the console box
2-50 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(131,1)
STORAGE
CV37D1-1541CD52-EDAB-422F-A971-82BAC026DA56
.
When not in use, be sure to close the
cap. Do not allow water or any liquid to
contact the outlet.
CUP HOLDERS
CV37D1-9FD9C96C-5FD2-489E-A25B-35DC5BEABC76
CAUTION
.
Avoid abrupt starting and braking when
the cup holder is being used to prevent
spilling the drink. If the liquid is hot, it
can scald you or your passenger.
.
Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.
JVI0649X
Front
JVI1492X
Rear
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-51
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(132,1)
CAUTION
JVI1500X
SOFT BOTTLE
HOLDER
CV37D1-DE4B7D45-7C80-4003-BE93-0BAAC75C570A
CAUTION
.
Do not use for anything other than
glasses.
.
Do not leave glasses in the sunglasses
holder while parking in direct sunlight.
The heat may damage the glasses.
JVI0651X
SUNGLASSES
HOLDER
CV37D1-BA6292D3-3959-4458-B5FE-E980BEA75EBD
WARNING
.
Do not use bottle holder for any other
objects that could be thrown about in the
vehicle and possibly injure people during sudden braking or an accident.
Keep the sunglasses holder closed while
driving to avoid obstructing the driver’s
view and to help prevent an accident.
.
Do not use bottle holder for open liquid
containers.
To open the sunglasses holder, push the
holder.
2-52 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(133,1)
JVI0763X
GLOVE BOX
CV37D1-F6CF0AA5-0A30-48C6-AD56-CE8831BA2E34
WARNING
Keep glove box lid closed while driving to
help prevent injury in an accident or a
sudden stop.
To open the glove box, pull the handle
JVI0653X
SIC4348
CONSOLE CV37D1-7E281298-B6E5-49A9-B436-68642C896FE8
BOX
CARD HOLDER
CV37D1-246B0920-FB36-4ED2-B10F-54EFFD4D038E
To open the console box, push up the knob
A and pull up the lid.
*
The card holder is located on the driver’s
sun visor.
To close, push the lid down until latched.
To use the card holder, slide the card in the
card holder.
The console box light illuminates when the
headlight switch is in the
position.
1 .
*
To close, push the lid in until the lock
latches.
2 /unlock *
3 the glove box, use
To lock *
the mechanical key. For the mechanical key
usage, see “Keys” (P.3-2).
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-53
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(134,1)
SIC4316
JVI1511X
STORAGE CV37D1-DF0A50D6-C446-40AF-A2DF-6B5E411C544A
BOX
COAT HOOKS
CV37D1-6E60A118-4C06-4622-A493-70124199F866
To open, push the storage box lid.
1 to
To use the coat hook, push the hook *
2 .
release *
Do not place valuable items in the storage
box.
Do not use the storage box as an ashtray.
CAUTION
Do not place items which are more than 2 lb
(1 kg) on the hook.
JVI1493X
TRUNK HOOKS
CV37D1-7F2F2069-5E83-4347-9CDB-726F230769B1
WARNING
.
Always make sure that the cargo is
properly secured. Use the suitable ropes
and hooks.
.
Unsecured cargo can become dangerous
in an accident or sudden stop.
2-54 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(135,1)
WINDOWS
CV37D1-AEEC66EB-668F-4E7B-84D1-AD1A2C0B8DED
CAUTION
Do not apply a total load of more than 22 lb
(10 kg) to a single hook.
POWER WINDOWS
CV37D1-32865A53-28E7-447C-A9B9-84195410C4C2
the windows is canceled.
WARNING
.
Make sure that all passengers have their
hands, etc. inside the vehicle while it is
in motion and before closing the windows. Use the window lock switch to
prevent unexpected use of the power
windows.
.
To help avoid risk of injury or death
through unintended operation of the
vehicle and or its systems, including
entrapment in windows or inadvertent
door lock activation, do not leave children, people who require the assistance
of others or pets unattended in your
vehicle. Additionally, the temperature
inside a closed vehicle on a warm day
can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
The power windows operate when the
ignition switch is in the ON position or for
about 45 seconds after the ignition switch
is pushed to the OFF position. If the driver’s
or front passenger’s door is opened during
this period of about 45 seconds, power to
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-55
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(136,1)
JVI1494X
1.
2.
3.
Driver side window
Front passenger side window
Window lock button
Main power window switch (driver’s
side)
CV37D1-4CC7580C-9AEC-4BCE-8EA6-560903CB5918
A
To open or close the window, push down *
B the switch and hold it. The
or pull up *
main switch (driver side switches) will open
or close all the windows.
SIC4353
Front passenger side power window switch
CV37D1-B42ADBEB-6953-4EEC-ADED-0C589C38B75B
The front passenger side switch will open
or close the front passenger side window.
To open or close the window, push down or
pull up the switch and hold it.
JVI1495X
AutomaticCV37D1-F5F5D3C4-D373-48F6-B2C1-91677EF6C965
operation
To fully open or close the window, completely push down or pull up the switch
and release it; it need not be held. The
window will automatically open or close all
the way. To stop the window, just push or
lift the switch in the opposite direction.
A light push or pull on the switch will cause
the window to open or close until the
switch is released.
Locking passenger’s
window
CV37D1-1AF70CF8-9271-414A-9F81-8379097AA7C3
C is pushed in, only
When the lock button *
the driver side window can be opened or
closed. Push it in again to cancel.
2-56 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(137,1)
Auto reverse
function
CV37D1-66ABF044-1E85-49F9-B21E-B3C2FACE3B04
WARNING
Automatic adjusting
function
GUID-D174165E-3003-4EEA-B2EE-619BFA291722
CAUTION
There are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers
have their hands, etc., inside the vehicle
before closing the window.
When the battery cable is removed from the
battery terminal, do not close either of the
front doors. The automatic window adjusting
function will not work and the side roof
panel may be damaged.
If the control unit detects something
caught in the window as it is closing, the
window will be immediately lowered.
The power window has an automatic
adjusting function. When the door is being
opened, the window is automatically lowered slightly to avoid contact between the
window and the side roof panel. When the
door is closed, the window is automatically
raised slightly.
The auto reverse function can be activated
when the window is closed by automatic
operation when the ignition switch is in the
ON position or for 45 seconds after the
ignition switch is pushed to the OFF
position.
Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the window
occurs.
While the automatic adjusting function
does not work, the window will be controlled as follows:
. When the door is opened, the window
lowers for approximately 2 seconds.
. While the door is open, the window
cannot be raised.
If the windows do not close automatically CV37D1-5018873A-9CDE-4190-B631-67416ADECA64
If the power window automatic function
(closing only) does not operate properly,
perform the following procedure to initialize the power window system.
1. Place the ignition switch in the ON
position.
2. Close the door.
3. Open the window completely by operating the power window switch.
4. Pull the power window switch and hold
it to close the window, and then hold
the switch more than 3 seconds after
the window is closed completely.
5. Release the power window switch.
Operate the window by the automatic
function to confirm the initialization is
complete.
6. Perform steps 2 through 5 above for
other windows.
If the power window automatic function
does not operate properly after performing
the procedure above, it is recommended
you have your vehicle checked by an
INFINITI retailer.
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-57
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(138,1)
MOONROOF (if so equipped)
CV37D1-3D9EDB99-CE88-4104-A686-8F1FA044EF82
WARNING
.
In an accident you could be thrown from
the vehicle through an open moonroof.
Always use seat belts and child restraints.
.
Do not allow anyone to stand up or
extend any portion of their body out of
the moonroof opening while the vehicle
is in motion or while the moonroof is
closing.
POWER MOONROOF
CV37D1-C1CAC059-3CCB-4E01-98BE-41B5326A9282
The moonroof only operates when the
ignition switch is in the ON position.
The moonroof is operational for about 45
seconds, even if the ignition switch is
pushed to the OFF position. If the driver’s
door or the passenger’s door is opened
during this period of about 45 seconds,
power to the moonroof is canceled.
JVI0655X
SunshadeCV37D1-1CD6C51E-2CF6-43DE-9B7C-FDFE087F32E1
CAUTION
.
Remove water drops, snow, ice or sand
from the moonroof before opening.
.
Do not place any heavy object on the
moonroof or surrounding area.
The sunshade will open automatically
when the moonroof is opened. However,
it must be closed manually.
Tilting theCV37D1-7327959F-D789-4278-BFE2-34D57E1B72DD
moonroof
To tilt up, first close the moonroof, then
1
push the switch to the tilt up position *
and release it; it need not be held. To tilt
down the moonroof, push the switch to the
2 .
tilt down position *
Sliding the
moonroof
CV37D1-78F09A38-DBBE-4D88-953D-2C8E2EF42DCE
To fully open or close the moonroof, push
2
1
the switch to the open *
or close *
2-58 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(139,1)
position and release it; it need not be held.
The roof will automatically open or close all
the way. To stop the roof, push the switch
once more while it is opening or closing.
Auto reverse
function
CV37D1-FAC8DE64-E355-4396-BF7A-507608B95F7B
Operating moonroof with Intelligent Key (if
so equipped)
CV37D1-E4015F80-54F8-47FF-8F59-6B9BB1333A81
There are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers
have their hands, etc., inside the vehicle
before closing the moonroof.
The moonroof can be opened by pushing
the UNLOCK button on the Intelligent Key.
This function will not operate while the
moonroof timer is activated or when the
moonroof need to be initialized. For details
about the Intelligent Key button usage, see
“How to use remote keyless entry system”
(P.3-17).
Opening: CV37D1-2CDBA8EF-1D2A-4175-B845-A9115A81FDDB
To open the sunroof, push the UNLOCK
button on the Intelligent Key for about 3
seconds after the door is unlocked.
To stop opening, release the
button.
occurs.
If the moonroof
does not operate
CV37D1-62DFF97A-CA79-46FA-94FD-BBA830AE3E72
WARNING
If the control unit detects something
caught in the moonroof when it is closing,
the moonroof will be immediately opened.
The auto reverse function can be activated
when the moonroof is closed by automatic
operation when the ignition switch is in the
ON position or for about 45 seconds after
the ignition switch is pushed to the OFF
position.
If the moonroof cannot be closed automatically when the auto reverse function
activates due to a malfunction, push and
hold the moonroof switch to the close
1 .
position *
If the moonroof does not operate properly,
perform the following procedure to initialize the moonroof operation system.
1. If the moonroof is open, close it fully by
repeatedly pushing the moonroof
1 to tilt
switch to the close position *
the moonroof up.
2. Push and hold the switch to the close
1 .
position *
3. Release the moonroof switch after the
moonroof moves slightly up and down.
4. Push and hold the switch to the open
2 to fully tilt the moonroof
position *
down.
5. Check if the moonroof switch operates
normally.
If the moonroof does not operate properly
after performing the procedure above,
have your moonroof checked and repaired.
It is recommended you visit an INFINITI
retailer for this service.
Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the moonroof
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-59
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(140,1)
INTERIOR LIGHTS
CV37D1-597C12A9-9379-411B-9ABA-7239511EFB84
JVI0656X
MAP LIGHTS
CV37D1-35C4693D-F33B-4099-9E8D-4C1A607B8732
Push the button as illustrated to turn the
light on or off.
JVI0726X
JVI0657X
CONSOLECV37D1-47768EBA-C973-4A28-ADEC-628E8A59C63B
LIGHT (if so equipped)
INTERIOR CV37D1-28981B41-A540-466D-853C-8B7908116D1F
LIGHT CONTROL SWITCH
The console light will turn on whenever the
front parking lights or headlights are
illuminated.
1 ON switch
*
CV37D1-F809DC40-1F48-4B4C-A4C1-79026C84F715
1 is pushed in, the
When the ON switch *
map lights will illuminate. When the switch
is pushed off, the lights will not illuminate,
regardless of the condition.
2 DOOR OFF switch
*
CV37D1-9EC535D6-4F15-4248-98CF-6E94179633A3
2
When the DOOR OFF switch *
is not
pushed in, the map lights will illuminate
under the following conditions:
. ignition switch is switched to the OFF
position
2-60 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(141,1)
VANITY MIRROR LIGHTS
CV37D1-C411E7C5-750B-43CD-8458-695C07891728
— remain on for about 15 seconds.
. doors are unlocked by pushing the
UNLOCK button on the Intelligent Key
or one touch unlock sensor with the
ignition switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened and then closed
with the ignition switch in the LOCK
position
— remain on for about 15 seconds.
. any door is opened
— remain on while the door is opened.
When the door is closed, the lights
go off.
2 is pushed
When the DOOR OFF switch *
in, the map lights will not illuminate under
the above condition. The map lights can be
1 .
turned on only with the ON switch *
. any door is opened with the ignition
switch in any position
— remain on while the door is opened.
When the door is closed, the lights
go off.
CAUTION
Do not use for extended periods of time with
the engine stopped. This could result in a
discharged battery.
SIC3869
The light on the vanity mirror will turn on
when the cover on the vanity mirror is
opened.
When the cover is closed, the light will turn
off.
The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
The lights will also turn off after a period of
time when the lights remain illuminated to
prevent the battery from becoming discharged.
When [Lamp ON When Door Unlocks] is set
to the OFF position (see the Infiniti InTouch
Owner’s Manual), the lights will illuminate
under the following condition:
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-61
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(142,1)
TRUNK LIGHT
CV37D1-7524985D-2D56-4402-A015-B859C046D431
COURTESY LIGHT
CV37D1-A49514E4-7B46-4396-AD1D-05DFE545CE1D
The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the
light will turn off.
The light will also turn off after a period of
time when the light remains illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
HomeLink® UNIVERSAL TRANSCEIVER (if so
equipped)
CV37D1-92A0C504-6C64-4778-8C02-C2A068B8FADA
The HomeLink® Universal Transceiver provides a convenient way to consolidate the
functions of up to three individual handheld transmitters into one built-in device.
HomeLink® Universal Transceiver:
JVI1496X
When the doors are unlocked by pushing
the UNLOCK button on the Intelligent Key
or touching the one touch unlock sensor
with the ignition switch in the LOCK
A will illumiposition, the courtesy light *
nate.
To activate or deactivate the courtesy light,
set [Lamp ON When Door Unlocks]. See the
Infiniti InTouch Owner’s Manual.
. Will operate most Radio Frequency (RF)
devices such as garage doors, gates,
home and office lighting, entry door
locks and security systems.
. Is powered by your vehicle’s battery. No
separate batteries are required. If the
vehicle’s battery is discharged or is
disconnected, HomeLink® will retain all
programming.
When the HomeLink® Universal Transceiver is programmed, retain the original
transmitter for future programming procedures (Example: new vehicle purchases).
Upon sale of the vehicle, the programmed
HomeLink® Universal Transceiver buttons
should be erased for security purposes.
For additional information, refer to “Programming HomeLink®” (P.2-63).
WARNING
.
Do not use the HomeLink® Universal
Transceiver with any garage door opener
that lacks safety stop and reverse
2-62 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(143,1)
features as required by federal safety
standards. (These standards became
effective for opener models manufactured after April 1, 1982). A garage door
opener which cannot detect an object in
the path of a closing garage door and
then automatically stop and reverse,
does not meet current federal safety
standards. Using a garage door opener
without these features increases the risk
of serious injury or death.
.
.
During the programming procedure your
garage door or security gate will open
and close (if the transmitter is within
range). Make sure that people or objects
are clear of the garage door, gate, etc.
that you are programming.
Your vehicle’s engine should be turned
off while programming the HomeLink®
Universal Transceiver. Do not breathe
exhaust gases; they contain colorless
and odorless carbon monoxide. Carbon
monoxide is dangerous. It can cause
unconsciousness or death.
PROGRAMMING
HomeLink®
CV37D1-BCFB7DC4-8309-4E2D-9C8D-07DF7CEAF1D1
If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site
at: www.homelink.com or call 1-800-3553515.
NOTE:
It is also recommended that a new battery
be placed in the hand-held transmitter of
t h e d e v i c e b e i n g p ro g r a m m e d t o
HomeLink® for quicker programming and
accurate transmission of the radio-frequency.
1. Position the end of your hand-held
transmitter 1-3 in (26-76 mm) away
from the HomeLink® surface, keeping
1
the HomeLink® indicator light *
in
view.
JVI0428X
2. Using both hands, simultaneously
press and hold the desired HomeLink®
button and handheld transmitter button. DO NOT release until the
1 flashes
HomeLink® indicator light *
slowly and then rapidly. When the
indicator light flashes rapidly, both
buttons may be released. (The rapid
flashing indicates successful programming.)
NOTE:
Some devices to be programmed may
require you to replace Step 2 with the
cycling procedure noted in the “Programming HomeLink® for Canadian
Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-63
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(144,1)
stand on your vehicle to perform the
next steps.
customers and gate openers” (P.2-65).
4. At the receiver located on the garage
door opener motor in the garage, locate
the “learn” or “smart” button (the
name and color of the button may vary
by manufacturer but it is usually
located near where the hanging antenna wire is attached to the unit). If there
is difficulty locating the button, reference the garage door opener’s manual.
JVI0429X
3. Press and hold the programmed
HomeLink® button and observe the
indicator light.
. If the indicator light *
1
is solid/
continuous, programming is complete and your device should activate when the HomeLink® button is
pressed and released.
. If the indicator light *
1
blinks
rapidly for two seconds and then
turns to a solid/continuous light,
continue with Steps 4-6 for a rolling
code device. A second person may
make the following steps easier. Use
a ladder or other device. Do not
5. Press and release the “learn” or
“smart” button.
NOTE:
Once the button is pressed, you have
approximately 30 seconds to initiate
the next step.
6. Return to the vehicle and firmly press
and hold the programmed HomeLink®
button for two seconds and release.
Repeat the “press/hold/release” sequence up to 3 times to complete the
programming process. HomeLink ®
should now activate your rolling code
equipped device.
7. If you have any questions or are having
difficulty programming your
HomeLink ® buttons, refer to the
2-64 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(145,1)
HomeLink® web site at: www.homelink.
com or call 1-800-355-3515.
PROGRAMMING HomeLink® FOR
CANADIAN CUSTOMERS AND GATE
OPENERS CV37D1-7466E10D-6916-4AD5-990C-56C135EA9047
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission –
which may not be long enough for
HomeLink® to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are designed to “time-out” in the same manner.
If you live in Canada or you are having
difficulties programming a gate operator or
garage door opener by using the “Programming HomeLink®” procedures, replace “Programming HomeLink®” Step 2
with the following:
NOTE:
When programming a garage door opener,
etc., unplug the device during the “cycling” process to prevent possible damage
to the garage door opener components.
Step 2: Using both hands, simultaneously
press and hold the desired HomeLink®
button and the hand-held transmitter
button. During programming, your handheld transmitter may automatically stop
transmitting. Continue to press and hold
the desired HomeLink® button while you
press and re-press (“cycle”) your handheld transmitter every two seconds until
the frequency signal has been learned. The
HomeLink® indicator light will flash slowly
and then rapidly after several seconds
upon successful programming. DO NOT
release until the HomeLink® indicator light
flashes slowly and then rapidly. When the
indicator light flashes rapidly, both buttons may be released. The rapid flashing
indicates successful programming.
Proceed with “Programming HomeLink®”
step 3 to complete.
Remember to plug the device back in when
programming is completed.
OPERATING THE HomeLink® UNIVERSAL TRANSCEIVER
CV37D1-68B45786-8434-4904-8E07-727BE7C0FD07
The HomeLink® Universal Transceiver, after
it is programmed, can be used to activate
the programmed device. To operate, simply
press and release the appropriate programmed HomeLink® Universal Transceiver button. The amber indicator light will
illuminate while the signal is being trans-
mitted.
For convenience, the hand-held transmitter
of the device may also be used at any time.
PROGRAMMING TROUBLESHOOTING
CV37D1-25602324-74B5-44E4-8E4A-023461D5330B
If the HomeLink® does not quickly learn the
hand-held transmitter information:
. replace the hand-held transmitter batteries with new batteries.
. position the hand-held transmitter with
its battery area facing away from the
HomeLink® surface.
. press and hold both the HomeLink® and
hand-held transmitter buttons without
interruption.
. position the hand-held transmitter 1-3
in (26-76 mm) away from the
HomeLink® surface. Hold the transmitter in that position for up to 15
seconds. If HomeLink® is not programmed within that time, try holding
the transmitter in another position keeping the indicator light in view at all
times.
If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site
at: www.homelink.com or 1-800-355Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
2-65
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(146,1)
3515.
CLEARING THE PROGRAMMED INFORMATION
CV37D1-384954F2-8A6C-40E4-BF10-CB5485A0C2A5
The following procedure clears the programmed information from both buttons.
Individual buttons cannot be cleared.
However, individual buttons can be reprogrammed, see “Reprogramming a single
HomeLink® button” (P.2-66).
To clear all
programming
CV37D1-05026553-B3E4-4FE8-BAA8-8DF6B4E48B27
1. P r e s s a n d h o l d t h e t w o o u t e r
HomeLink® buttons until the indicator
light begins to flash in approximately
10 seconds. Do not hold for longer than
20 seconds.
2. Release both buttons.
®
HomeLink is now in the programming
mode and can be programmed at any time
beginning with “Programming HomeLink®”
- Step 1.
REPROGRAMMING A SINGLE
®
HomeLinkCV37D1-5744F383-98D4-4FDB-B598-C6A4049E38AD
BUTTON
®
To reprogram a HomeLink
Universal
Transceiver button, complete the following.
1. Press and hold the desired HomeLink®
button. Do not release the button.
2. The indicator light will begin to flash
after 20 seconds. Without releasing the
HomeLink® button, proceed with “Programming HomeLink®” - Step 1.
For questions or comments, contact
HomeLink® at: www.homelink.com or 1800-355-3515.
The HomeLink® Universal Transceiver button has now been reprogrammed. The new
device can be activated by pushing the
HomeLink® button that was just programmed. This procedure will not affect
any other programmed HomeLink® buttons.
IF YOUR VEHICLE
IS STOLEN
CV37D1-2BD85D86-7F7F-430B-8EC0-24D0C3D0258B
If your vehicle is stolen, you should change
the codes of any non-rolling code device
that has been programmed into
HomeLink®. Consult the Owner’s Manual
of each device or call the manufacturer or
retailer of those devices for additional
information.
When your vehicle is recovered, you will
need to reprogram the HomeLink® Universal Transceiver with your new transmitter information.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
2-66 Instruments and controls
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(147,1)
3 Pre-driving checks and adjustments
Keys ...................................................................
...
3-2
Intelligent Key ................................................
...
3-2
Valet hand-off .................................................
...
3-4
Doors .................................................................
...
3-4
Locking with mechanical key ..........................
...
3-4
Opening and closing windows with
mechanical key ...............................................
...
3-5
Locking with inside lock knob .........................
...
3-5
Locking with power door lock switch ..............
...
3-5
Automatic door locks ......................................
...
3-6
Intelligent Key system .........................................
...
3-6
Intelligent Key operating range .......................
...
3-8
Door locks/unlocks precaution ......................
...
3-9
Intelligent Key operation ...............................
...
3-10
Battery saver system ....................................
...
3-13
Warning signals ............................................
...
3-14
Troubleshooting guide ..................................
...
3-15
Log-in function .............................................
...
3-16
Remote keyless entry system ............................
...
3-16
How to use remote keyless entry system ......
... 3-17
Remote engine start (if so equipped) ................
...
3-20
Remote engine start operating range ............
...
3-21
Remote starting the engine ..........................
...
3-21
Extending engine run time ............................
...
3-21
Condition:
Canceling a remote start .............................
...
Conditions the remote start will not work ....
...
Hood ................................................................
...
Trunk lid ..........................................................
...
Trunk lid release switch ..............................
...
Trunk open request switch ..........................
...
TRUNK button .............................................
...
Trunk release power cancel switch ..............
...
Interior trunk lid release .............................
...
Fuel-filler door ..................................................
...
Opening the fuel-filler door .........................
...
Fuel-filler cap ..............................................
...
Tilt/telescopic steering .....................................
...
Manual operation (if so equipped) ..............
...
Electric operation (if so equipped) ...............
...
Sun visors ........................................................
...
Mirrors .............................................................
...
Inside mirror ...............................................
...
Outside mirrors ...........................................
...
Vanity mirror ...............................................
...
Automatic drive positioner (if so equipped) ......
...
Memory storage ..........................................
...
System operation ........................................
...
[ Edit: 2016/ 4/ 27
3-22
3-22
3-23
3-23
3-24
3-24
3-24
3-25
3-25
3-26
3-26
3-26
3-28
3-29
3-29
3-29
3-30
3-30
3-31
3-33
3-33
3-33
3-34
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(148,1)
KEYS
CV37D1-34905E83-1F92-42BA-9201-6E547D9CC6E7
1.
2.
3.
A key number plate is supplied with your
keys. Record the key number and keep it in
a safe place (such as your wallet), not in
the vehicle. If you lose your keys, it is
recommended you visit an INFINITI retailer
for duplicates by using the key number.
INFINITI does not record any key numbers
so it is very important to keep track of your
key number plate.
A key number is only necessary when you
have lost all keys and do not have one to
duplicate from. If you still have a key, it can
be duplicated without knowing the key
number.
Intelligent Keys (2)
Mechanical keys (inside the Keys) (2)
Key number plate (1)
INTELLIGENT
KEY
CV37D1-983099D0-6576-4B3D-89E3-E144CB5578B2
SPA2865
Type A (if so equipped)
Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system components and INFINITI Vehicle Immobilizer
System components. As many as 4 Intelligent Keys can be registered and used with
one vehicle. The new keys must be
registered by an INFINITI retailer prior to
use with the Intelligent Key system and
INFINITI Vehicle Immobilizer System of your
vehicle. Since the registration process
requires erasing all memory in the Intelligent Key components when registering
new keys, be sure to take all Intelligent
Keys that you have to the INFINITI retailer.
It is possible that the Intelligent Key
functions become canceled. Contact an
INFINITI retailer.
CAUTION
.
JVP0414X
Type B (if so equipped)
Be sure to carry the Intelligent Key with
you when driving. The Intelligent Key is a
precision device with a built-in transmit-
3-2 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(149,1)
ter. To avoid damaging it, please note the
following.
— The Intelligent Key is water resistant; however, wetting may damage
the Intelligent Key. If the Intelligent
Key gets wet, immediately wipe until
it is completely dry.
— Do not bend, drop or strike it
against another object.
the system function.
.
If an Intelligent Key is lost or stolen,
INFINITI recommends erasing the ID code
of that Intelligent Key. This will prevent
the Intelligent Key from unauthorized
use to unlock the vehicle. For information regarding the erasing procedure, it
is recommended you visit an INFINITI
retailer.
— If the outside temperature is below
148F (−108C), the battery of the
Intelligent Key may not function
properly.
SPA2033
Mechanical
key
CV37D1-8F7AE54A-7165-48B3-9269-5DC241EF3538
— Do not place the Intelligent Key for
an extended period in a place where
temperatures exceed 1408F (608C).
To remove the mechanical key, release the
lock knob at the back of the Intelligent Key.
To install the mechanical key, firmly insert
it into the Intelligent Key until the lock
knob returns to the lock position.
— Do not change or modify the Intelligent Key.
— Do not use a magnet key holder.
Use the mechanical key to lock or unlock
the doors and glove box, if they are
equipped with a key cylinder.
— Do not place the Intelligent Key near
an electric appliance such as a
television set or personal computer.
See “Doors” (P.3-4) and “Glove box” (P.253).
— Do not allow the Intelligent Key to
come into contact with water or salt
water, and do not wash it in a
washing machine. This could affect
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(150,1)
DOORS
CV37D1-177D3333-D318-4851-983B-CCA9E4D9C481
CAUTION
Always carry the mechanical key installed in
the key.
WARNING
.
Always have the doors locked while
driving. Along with the use of seat belts,
this provides greater safety in the event
of an accident by helping to prevent
persons from being thrown from the
vehicle. This also helps keep children
and others from unintentionally opening
the doors, and will help keep out
intruders.
.
Before opening any door, always look for
and avoid oncoming traffic.
.
To help avoid risk of injury or death
through unintended operation of the
vehicle and or its systems, including
entrapment in windows or inadvertent
door lock activation, do not leave children, people who require the assistance
of others or pets unattended in your
vehicle. Additionally, the temperature
inside a closed vehicle on a warm day
can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
VALET HAND-OFF
CV37D1-0CF61D1C-5574-4FED-B636-199A26014C96
When you have to leave a key with a valet,
give them the Intelligent Key itself and
keep the mechanical key with you to
protect your belongings.
To prevent the glove box and the trunk from
being opened during valet hand-off, follow
the procedures below.
1. Push the trunk release power cancel
switch to the OFF (cancel) side.
2. Remove the mechanical key from the
Intelligent Key.
3. Lock the glove box with the mechanical
key.
4. Hand the Intelligent Key to the valet,
keeping the mechanical key in your
pocket or bag for insertion into the
Intelligent Key when you retrieve your
vehicle.
See “Trunk lid” (P.3-23) and “Glove box”
(P.2-53).
3-4
JVP0231X
LOCKING CV37D1-C25772FF-54AB-4B29-905A-20D8DCADE361
WITH MECHANICAL KEY
The power door lock system allows you to
lock or unlock all doors, trunk lid simultaneously using the mechanical key.
. Turning the driver’s door key cylinder to
1 will lock all
the front of the vehicle *
doors and trunk lid.
. Turning the driver’s door key cylinder
2 will
once to the rear of the vehicle *
unlock the driver’s door. After returning
3 ,
the key to the neutral position *
turning it to the rear again within 60
seconds will unlock all doors and trunk
lid.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(151,1)
. You can switch the lock system to the
mode that allows you to open all the
doors when the key is turned once. (See
the Infiniti InTouch Owner’s Manual for
details.)
OPENING AND CLOSING WINDOWS
WITH MECHANICAL
KEY
CV37D1-4F532F02-D91C-4F3D-A52B-22AB4EC3B1EB
The driver’s door key operation also allows
you to open and close the window that is
equipped with the automatic open/close
function. (See “Power windows” (P.2-55).)
To open the window, turn the driver’s door
key cylinder to the rear of the vehicle for
longer than 1 second. The door is unlocked
and the window keeps opening while
turning the key.
This function can also be performed by
pushing and holding the UNLOCK button
on the Intelligent Key. (See “Remote keyless entry system” (P.3-16).)
To close the window, turn the driver’s door
key cylinder to the front of the vehicle for
longer than 1 second. The door is locked
and the window keeps closing while turning the key.
SPA2726
LOCKING CV37D1-DECCBDA4-1FFA-4625-B403-AD821861120A
WITH INSIDE LOCK KNOB
To lock the door individually, move the
1
inside lock knob to the lock position *
then close the door.
To unlock, move the inside lock knob to the
2 .
unlock position *
When locking the door without an Intelligent Key, be sure not to leave the
Intelligent Key inside the vehicle.
JVP0319X
LOCKING WITH POWER DOOR LOCK
SWITCH CV37D1-CBF91FA3-454F-40CE-BEC9-D677B62EA9F7
Operating the power door lock switch will
lock or unlock all the doors and trunk lid.
The switches are located on the driver’s
and front passenger’s door armrests.
To lock the doors and trunk lid, push the
power door lock switch to the lock position
1 with the driver’s or front passenger’s
*
door open, then close the door.
When locking the door this way, be certain
not to leave the Intelligent Key inside the
vehicle.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(152,1)
INTELLIGENT KEY SYSTEM
CV37D1-B796E83A-48EA-4DBB-A93C-527D070256D5
To unlock the doors including the fuel-filler
door and trunk lid, push the power door
2 .
lock switch to the unlock position *
Lockout protection
CV37D1-DF6148C7-7E14-418E-86BE-0AA2CB5A89A2
When the power door lock switch is moved
to the lock position and any door open, all
doors will lock and unlock automatically.
With the Intelligent Key left in the vehicle
and any door open, all doors will unlock
automatically and a chime will sound after
the door is closed.
The automatic unlock function can be
deactivated or activated. To deactivate or
activate the automatic door unlock system,
perform the following procedure:
Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufacturer for the possible influences before
use.
.
The Intelligent Key transmits radio
waves when the buttons are pushed.
The FAA advises that the radio waves
may affect aircraft navigation and communication systems. Do not operate the
Intelligent Key while on an airplane.
Make sure the buttons are not operated
unintentionally when the unit is stored
during a flight.
2. Place the ignition switch in the ON
position.
3. Within 20 seconds of performing Step
2, push and hold the power door lock
switch to the
position (UNLOCK) for
more than 5 seconds.
4. When activated, the hazard indicator
will flash twice. When deactivated, the
hazard indicator will flash once.
AUTOMATIC
DOOR LOCKS
CV37D1-AE3E4033-C3D5-450F-974A-E26F92F12E2C
5. The ignition switch must be placed in
the OFF and ON position again between
each setting change.
3-6
.
1. Close all doors.
These functions help to prevent the Intelligent Key from being accidentally
locked inside the vehicle.
. All doors and trunk lid lock automatically when the vehicle speed reaches
15 MPH (24 km/h).
. All doors and trunk lid unlock automatically when the ignition switch is
placed in the OFF position or when the
shift lever is moved to the P (Park)
position, if selected.
WARNING
When the automatic door unlock system is
deactivated, the doors do not unlock when
the ignition switch is placed in the OFF
position. To unlock the door manually, use
the inside lock knob or the power door lock
switch (driver’s or front passenger’s side).
The automatic door unlock function can be
changed on the lower display. (See the
Infiniti InTouch Owner’s Manual.)
The Intelligent Key system can operate all
the doors and the trunk lid using the
remote controller function, using one touch
unlock function or pushing the request
switch on the vehicle without taking the
key out from a pocket or purse. The
operating environment and/or conditions
may affect the Intelligent Key system
operation.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(153,1)
Be sure to read the following before using
the Intelligent Key system.
CAUTION
.
Be sure to carry the Intelligent Key with
you when operating the vehicle.
.
Never leave the Intelligent Key in the
vehicle when you leave the vehicle.
The Intelligent Key is always communicating with the vehicle as it receives radio
waves. The Intelligent Key system transmits weak radio waves. Environmental
conditions may interfere with the operation
of the Intelligent Key system under the
following operating conditions.
. When operating near a location where
strong radio waves are transmitted,
such as a TV tower, power station and
broadcasting station.
. When in possession of wireless equipment, such as a cellular telephone,
transceiver, and CB radio.
. When the Intelligent Key is in contact
with or covered by metallic materials.
. When any type of radio wave remote
control is used nearby.
. When the Intelligent Key is placed near
an electric appliance such as a personal
computer.
. When the vehicle is parked near a
parking meter.
In such cases, correct the operating conditions before using the Intelligent Key
function or use the mechanical key.
Although the life of the battery varies
depending on the operating conditions,
the battery’s life is approximately 2 years.
If the battery is discharged, replace it with
a new one.
When the Intelligent Key battery is almost
discharged, see “Intelligent Key battery
discharge” (P.5-14) to start the engine.
Since the Intelligent Key is continuously
receiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and
personal computer, the battery life may
become shorter.
For information regarding replacement of a
battery, see “Intelligent Key battery replacement” (P.8-28).
As many as 4 Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use of
additional Intelligent Keys, contact an
INFINITI retailer.
CAUTION
.
Do not allow the Intelligent Key, which
contains electrical components, to come
into contact with water or salt water. This
could affect the system function.
.
Do not drop the Intelligent Key.
.
Do not strike the Intelligent Key sharply
against another object.
.
Do not change or modify the Intelligent
Key.
.
Wetting may damage the Intelligent Key.
If the Intelligent Key gets wet, immediately wipe until it is completely dry.
.
Do not place the Intelligent Key for an
extended period in an area where temperatures exceed 1408F (608C).
.
If the outside temperature is below 148F
(−108C), the battery of the Intelligent
Key may not function properly.
.
Do not attach the Intelligent Key with a
key holder that contains a magnet.
.
Do not place the Intelligent Key near
equipment that produces a magnetic
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(154,1)
cm) from each one touch unlock sensor/
1 and trunk
door handle request switch *
2 .
open request switch *
field, such as a TV, audio equipment and
personal computers.
If the Intelligent Key is too close to the door
glass, handle or rear bumper, the one
touch unlock sensor and request switches
may not function.
If an Intelligent Key is lost or stolen,
INFINITI recommends erasing the ID code
of that Intelligent Key from the vehicle. This
may prevent the unauthorized use of the
Intelligent Key to operate the vehicle. For
information regarding the erasing procedure, contact an INFINITI retailer.
JVP0453X
When the Intelligent Key is within the
operating range, it is possible for anyone
who does not carry the Intelligent Key to
use the one touch unlock sensor or request
switches to lock or unlock the doors and
open the trunk lid.
INTELLIGENT KEY OPERATING
RANGE CV37D1-C3F09254-070A-44F2-B7E6-7B0B79DCB094
The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range from the one
touch unlock sensor/door request switch
1 and trunk open request switch *
2 .
*
When the Intelligent Key battery is discharged or strong radio waves are present
near the operating location, the Intelligent
Key system’s operating range becomes
narrower, and the Intelligent Key may not
function properly.
The operating range is within 31.50 in (80
3-8
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(155,1)
.
.
SPA2407
DOOR LOCKS/UNLOCKS PRECAUTION
CV37D1-B9E67E72-CE1C-4540-9CC5-4903AA1FB49B
. Do not push the door handle request
switch with the Intelligent Key held in
your hand as illustrated. The close
distance to the door handle will cause
the Intelligent Key system to have
difficulty recognizing that the Intelligent Key is outside the vehicle.
. Within 2 seconds after the door are
locked using the door handle request
switch, make sure that the doors have
been securely locked by operating the
door handles. If you keep holding the
door handle for more than 2 seconds
.
.
.
after locking the doors using the door
handle request switch, the door will be
unlocked.
To prevent the Intelligent Key from
being left inside the vehicle or the
trunk, make sure you carry the key with
you and then lock the doors or the
trunk.
The Intelligent Key system (opening/
closing doors with the door handle
request switch or one touch unlock
sensor) can be set to remain inactive.
(See the Infiniti InTouch Owner’s Manual.)
The door cannot be unlocked using one
touch unlock operation after locking the
door within 2 seconds. To unlock the
door, release the one touch unlock
sensor once and touch it again.
If a large amount of water runs down on
the door handle (for example, when
washing the vehicle or in a heavy rain),
the door may unlock if the Intelligent
Key is within the range of operation. To
prevent the door from being unlocked,
the Intelligent Key should be away from
the vehicle more than 7 ft (2 m).
Do not hold and pull the door handle
quickly. The door will be unlocked but
will not open. Release the door handle
once and pull it again to open the door.
. If you pull the door handle with your
gloved hand, the one touch unlock
operation may not function.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(156,1)
JVP0415X
INTELLIGENT
KEY OPERATION
CV37D1-B50EEA23-6967-433E-9B47-520BF073059B
You can lock or unlock the doors without
taking the key out from your pocket or bag.
JVP0448X
When you carry the Intelligent Key with
you, you can lock all doors by pushing the
A (driver’s or
door handle request switch *
front passenger’s) within the range of
operation.
JVP0449X
You can also unlock the corresponding
door by touching the one touch unlock
B (driver’s or front passenger’s)
sensor *
within the range of operation, and can
unlock the other doors using the door
A .
handle request switch *
When you lock or unlock the doors or the
trunk lid, the hazard indicator will flash
and the horn (or the outside chime) will
sound as a confirmation. For details, see
“Setting hazard indicator and horn mode”
(P.3-19).
3-10 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(157,1)
CAUTION
.
After locking the doors using the request
switch, make sure that the doors have
been securely locked by operating the
door handles.
.
When locking the doors using the
request switch, make sure to have the
Intelligent Key in your possession before
operating the request switch to prevent
the Intelligent Key from being left in the
vehicle.
.
The request switch and one touch unlock
sensor are operational only when the
Intelligent Key has been detected by the
Intelligent Key system.
Welcome light and farewell light
function CV37D1-79ABEFFA-36FC-44D4-86B9-4E786EBEA8BE
When you lock or unlock the doors and
fuel-filler door, front and rear side marker
lights, parking lights, emblem light (if so
equipped), tail lights and the license plate
light will illuminate for a period of time. The
welcome light and farewell light function
can be disabled. For information about
disabling the welcome light and farewell
light function, see the Infiniti InTouch
Owner’s Manual.
.
When the Intelligent Key is placed inside
the door pockets.
Lockout protection
CV37D1-B6EB1162-CCA6-4EBC-9F3F-C27EA38C3BF5
.
When the Intelligent Key is placed inside
or near metallic materials.
To prevent the Intelligent Key from being
accidentally locked in the vehicle, lockout
protection is equipped with the Intelligent
Key system.
When the driver’s side door is open, the
doors are locked, and then the Intelligent
Key is put inside the vehicle and all the
doors are closed; the lock will automatically unlock and the door buzzer sounds.
NOTE:
The doors may not lock when the Intelligent Key is in the same hand that is
operating the request switch to lock the
door. Put the Intelligent Key in a purse,
pocket or your other hand.
CAUTION
The lockout protection may not function
under the following conditions:
.
When the Intelligent Key is placed on top
of the instrument panel.
.
When the Intelligent Key is placed inside
the glove box or a storage bin.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(158,1)
*1: Doors will lock with the Intelligent Key
while the ignition switch is in the ACC
or ON position.
*2: Doors will not lock with the Intelligent
Key while any door is open.
*3: Doors will not lock by pushing the
door handle request switch with the
Intelligent Key inside the vehicle.
However, when an Intelligent Key is
inside the vehicle, doors can be
locked with another registered Intelligent Key.
JVP0448X
JVP0449X
Locking doors, trunk lid and fuelfiller doorCV37D1-661DB761-980D-489C-83F6-7554616799D9
UnlockingCV37D1-67487D33-3407-4172-8184-7F095CB75C46
doors and fuel-filler door
B
1. Touch the one touch unlock sensor *
(driver’s or front passenger’s) while
carrying the Intelligent Key with you.
1. Push the ignition switch to the OFF
position and make sure you carry the
Intelligent Key with you.*1
2. The hazard indicator flashes once and
the outside chime sounds once. The
corresponding door will unlock.
2. Close all the doors.*2
3. Push the door handle request switch
A while
(driver’s or front passenger’s) *
carrying the Intelligent Key with you.*3
A
3. Push the door handle request switch *
within 1 minute.
4. The hazard indicator flashes once and
the outside chime sounds once again.
All the doors, trunk lid and fuel-filler
door will unlock.
4. All the doors, trunk lid and fuel-filler
door will lock.
5. The hazard indicator flashes twice and
the outside chime sounds twice.
All doors, trunk lid and fuel-filler door will
3-12 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(159,1)
Opening CV37D1-F97D0FED-C0AB-491B-A879-BBFC4B7BD1C7
trunk lid
be locked automatically unless one of the
following operations is performed within 1
minute after pushing the request switch or
touch unlock operation while the doors are
locked.
A
1. Push the trunk open request switch *
for more than 1 second while carrying
the Intelligent Key with you.
2. The trunk will unlatch. An outside
chime will sound four times.
. Opening any door
. Pushing the ignition switch
During this 1-minute time period, if the
UNLOCK
button on the Intelligent Key
is pushed, all doors will be locked automatically after another 1 minute.
3. Raise the trunk lid to open the trunk.
JVP0450X
Lockout protection:
CV37D1-B8CD4C00-DA8D-4CD7-A211-CAF92D749A1E
To prevent the Intelligent Key from being
accidentally locked in the trunk, lockout
protection is equipped with the Intelligent
Key system.
When the trunk lid is closed with the
Intelligent Key inside the trunk, the outside
chime will sound and the trunk will open.
BATTERY SAVER
SYSTEM
CV37D1-9C90E7C9-246A-4623-83FA-CF0DC4853695
When all the following conditions are met
for a period of time, the battery saver
system will cut off the power supply to
prevent battery discharge.
. The ignition switch is in the ACC
position, and
. All doors are closed, and
. The shift lever is in the P (Park) position.
JVP0451X
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(160,1)
WARNINGCV37D1-23FEF2BD-D391-4ABA-98C9-E493D5D04610
SIGNALS
To help prevent the vehicle from moving
unexpectedly by erroneous operation of
the Intelligent Key listed on the following
chart or to help prevent the vehicle from
being stolen, chime or beep sounds inside
and outside the vehicle and a warning
displays in the vehicle information display.
When a chime or beep sounds or the
warning displays, be sure to check the
vehicle and Intelligent Key.
See “Troubleshooting guide” (P.3-15) and
“Vehicle information display” (P.2-21).
3-14 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(161,1)
TROUBLESHOOTING
GUIDE
CV37D1-D8F8E377-3ADD-473B-82BB-D3262AC2D311
Symptom
Action to take
Possible cause
The SHIFT P warning appears on the display
When pushing the ignition switch
and the inside warning chime sounds conto stop the engine
tinuously.
The shift lever is not in the P (Park)
position.
Shift the shift lever to the P (Park) position.
When shifting the shift lever to
the P (Park) position.
The ignition switch is in the ACC or ON
position.
Push the ignition switch to the OFF position.
The ignition switch is in the ACC position.
Push the ignition switch to the OFF position.
The NO KEY warning appears on the display,
the outside chime sounds 3 times and the
inside warning chime sounds for a few
seconds.
The ignition switch is in the ACC or ON
position.
Push the ignition switch to the OFF position.
The SHIFT P warning appears on the display
and the outside chime sounds continuously.
The ignition switch is in the ACC or OFF Move the shift lever to the P (Park) position
position and the shift lever is not in the and push the ignition switch to the OFF
position.
P (Park) position.
The outside chime sounds for a few seconds
and all the doors unlock.
The Intelligent Key is inside the vehicle Carry the Intelligent Key with you.
or trunk.
When pushing the request switch
or LOCK button on the Intelligent The outside chime sounds for a few seconds.
Key to lock the door
The Intelligent Key is inside the vehicle Carry the Intelligent Key with you.
or trunk.
Close the door securely.
A door is not closed securely.
The inside warning chime sounds continuously.
When opening the driver’s door to The inside warning chime sounds continuget out of the vehicle
ously.
When closing the door after getting out of the vehicle
When closing the door with the
inside lock knob turned to LOCK
When closing the trunk lid
The outside chime sounds for approximately
10 seconds and the trunk lid opens.
The Intelligent Key is inside the trunk.
Carry the Intelligent Key with you.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(162,1)
REMOTE KEYLESS ENTRY SYSTEM
CV37D1-C688401E-E9F3-470C-9900-CC16F907F8D2
LOG-IN FUNCTION
CV37D1-CA6124FC-8EBA-462D-86D2-147138D1E5D5
After setting up the user information, the
system will automatically recognize the
user upon turning on the vehicle.
There will be a personalized welcome
greeting and screen prompt to log-in.
This feature allows 4 drivers to use their
own registration, drive mode, driving position, air conditioner, and auto settings and
memorizes these custom settings.
. Steering
. Suspension (if so equipped)
. Active trace control system
. Driver assistance* (if so equipped)
. Body Control Module (BCM)
*: except for the Forward Emergency
Braking (FEB) system
The log-in user can be changed on the
welcome greeting screen or the User List
screen. For more details, see the Infiniti
InTouch Owner’s Manual.
WARNING
The Intelligent Key transmits radio waves
when the buttons are pushed. The FAA
advises that the radio waves may affect
aircraft navigation and communication systems. Do not operate the Intelligent Key
while on an airplane. Make sure the buttons
are not operated unintentionally when the
unit is stored during a flight.
It is possible to lock/unlock all doors and
fuel-filler door, open the trunk lid, activate
the panic alarm and open the windows by
pushing the buttons on the Intelligent Key
from outside the vehicle.
The log-in function is linked to the following items:
Before locking the doors, make sure the
Intelligent Key is not left in the vehicle.
. Meter
. Audio
. Navigation system display (if so
equipped)
. Navigation settings (if so equipped)
. Air conditioner
. Automatic drive positioner (if so
equipped)
. Engine/Transmission
The remote keyless entry function can
operate at a distance of approximately 33
ft (10 m) from the vehicle. (The effective
distance depends upon the conditions
around the vehicle.)
As many as 4 Intelligent Keys can be used
with one vehicle. For information concerning the purchase and use of additional
Intelligent Keys, contact an INFINITI retailer.
3-16 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(163,1)
1.
2.
3.
4.
5.
The buttons on the Intelligent Key will not
operate when:
. the distance between the Intelligent Key
and the vehicle is over 33 ft (10 m).
. the Intelligent Key battery is discharged.
After locking with the remote keyless entry
function, pull the door handle to make sure
the doors are securely locked.
The LOCK/UNLOCK operating range varies
depending on the environment. To securely
operate the lock and unlock buttons,
approach the vehicle to about 3 ft (1 m)
from the door.
LOCK button
UNLOCK button
TRUNK button
PANIC button
Remote engine start button
HOW TO USE REMOTE KEYLESS
ENTRY SYSTEM
CV37D1-17AB4EB7-4769-4F15-B7CB-CAD2CBDD45D7
SPA2100
Type A (if so equipped)
When you lock or unlock the doors or the
trunk lid, the hazard indicator will flash
and the horn (or the outside chime) will
sound as a confirmation. For details, see
“Setting hazard indicator and horn mode”
(P.3-19).
Locking doors, trunk lid and fuelfiller doorCV37D1-E9C01606-95CE-4FEE-9BEC-65E3B96B2733
1. Push the ignition switch to the OFF
position and make sure you carry the
Intelligent Key with you.*1
2. Close all the doors.
3. Push the LOCK
Intelligent Key.
button
1
*
on the
4. All the doors, trunk lid and fuel-filler
door will lock.
JVP0409X
5. The hazard indicator flashes twice and
the horn chirps once.
Type B (if so equipped)
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(164,1)
*1: Doors will lock with the Intelligent Key
while the ignition switch is in the ACC
or ON position.
Unlocking doors, trunk lid and fuelfiller doorCV37D1-CACAF5DB-E00C-4137-8A50-620148E04858
2 on the
1. Push the UNLOCK
button *
Intelligent Key once.
2. The hazard indicator flashes once. The
driver’s door will unlock.
2 on the
3. Push the UNLOCK
button *
Intelligent Key again within 1 minute.
4. The hazard indicator flashes once
again. All the doors, trunk lid and the
fuel-filler door will unlock.
All doors, trunk lid and the fuel-filler door
will be locked automatically unless one of
the following operations is performed
within 1 minute after pushing the UNLOCK
2 button on the Intelligent Key while
*
the doors are locked. If during this 12
minute time period, the UNLOCK
*
button on the Intelligent Key is pushed, all
doors will be locked automatically after
another 1 minute.
. Opening any door
. Pushing the ignition switch
Opening CV37D1-C312D8D6-DA39-443A-B386-43A24CA3CA9A
windows (if so equipped)
2 operation also
The UNLOCK
button *
allows you to open the window that is
equipped with the automatic open/close
function. (See “Power windows” (P.2-55).)
To open the window, push the door
2 button on the Intelligent
UNLOCK
*
Key for about 3 seconds after the door is
unlocked.
To stop opening, release the UNLOCK
2 .
button *
To open the moonroof, push the UNLOCK
2 on the Intelligent Key for
button *
about 3 seconds after the door is unlocked.
To stop opening, release the UNLOCK
2 .
button *
Opening trunk
lid
CV37D1-DE9E3776-94FB-4A31-AD24-12EE8E628311
3 on the
1. Push the TRUNK
button *
Intelligent Key for more than 1 second.
2. The trunk will unlatch.
3. Raise the trunk lid to open the trunk.
If the window open operation is stopped in
mid-operation while pushing the UNLOCK
2
button *
, release and push the
2
UNLOCK
button *
again until the
window opens completely.
Window cannot be closed using the Intelligent Key.
The door window can also be operated by
turning the mechanical key in a door lock.
(See “Doors” (P.3-4).)
Opening CV37D1-42903FC0-2C8D-4BC8-BEA1-C14C5687BB8B
moonroof (if so equipped)
The moonroof can be opened by pushing
2 on the Intellithe UNLOCK
button *
gent Key. This function will not operate
while the moonroof timer is activated or
when the windows need to be initialized.
Using panic
alarm
CV37D1-C48ED9A1-9FD0-4D97-98ED-384A5E9B57B7
If you are near your vehicle and feel
threatened, you may activate the alarm to
call attention as follows:
4 on the
1. Push the PANIC
button *
key for more than 1 second.
2. The theft warning alarm and headlights
will stay on for 25 seconds.
3. The panic alarm stops when:
. It has run for 25 seconds, or
. Any of the buttons on the Intelligent
Key are pushed. (Note: PANIC
4 or TRUNK
3
button *
button *
should be pushed for more than 1
second.)
3-18 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(165,1)
Remote engine start (if so
equipped)CV37D1-AF1F4306-94AF-46A8-B12A-099E86C5E97E
5 is
The remote engine start
button *
on the Intelligent Key if the vehicle has
remote engine start function. This function
allows the engine to start from outside the
vehicle. See “Remote engine start” (P.3-20)
for more details.
Setting hazard indicator and horn
mode
CV37D1-A40448AF-C6FA-43AE-92F5-1D5AEFB7DEBC
This vehicle is set in hazard indicator and
horn mode when you first receive the
vehicle.
In hazard indicator and horn mode, when
1 is pushed, the
the LOCK
button *
hazard indicator flashes twice and the horn
chirps once. When the UNLOCK
button
2 is pushed, the hazard indicator flashes
*
once.
Hazard indicator and horn mode:
CV37D1-C83D0F83-579A-402D-BE01-BBB2463BC8AD
DOOR LOCK
Intelligent Key system
(Using door handle or trunk
request switch)
HAZARD - twice
OUTSIDE CHIME - twice
Remote keyless entry system
HAZARD - twice
(Using
,
or
button)
HORN - once
DOOR UNLOCK
TRUNK UNLOCK
HAZARD - once
OUTSIDE CHIME - once
HAZARD - none
OUTSIDE CHIME - 4
times
HAZARD - once
HORN - none
HAZARD - none
HORN - none
Hazard indicator mode:
CV37D1-255A333C-9EEF-4C6C-B606-492BFAD9027F
Intelligent Key system
(Using door handle or trunk
request switch)
DOOR LOCK
DOOR UNLOCK
TRUNK UNLOCK
HAZARD - twice
OUTSIDE CHIME - none
HAZARD - none
OUTSIDE CHIME - none
HAZARD - none
OUTSIDE CHIME - none
HAZARD - once
HORN - none
HAZARD - none
HORN - none
Remote keyless entry system
HAZARD - twice
(Using
,
or
button)
HORN - none
If horns are not necessary, the system can
be switched to the hazard indicator mode.
In hazard indicator mode, when the LOCK
1
button *
is pushed, the hazard
indicator flashes twice. When the UNLOCK
2
button *
is pushed, neither the
hazard indicator nor the horn operates.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(166,1)
REMOTE ENGINE START (if so equipped)
CV37D1-7E9CA873-22D0-4B8B-9853-A27BC4348694
Switching procedure:
CV37D1-383F1B1E-A2BA-4364-8DED-2DF4A9AEDE13
To switch the hazard indicator and horn
1
(chime) operation, push the LOCK
*
2 buttons on the Inteland UNLOCK
*
ligent Key simultaneously for more than 2
seconds.
. When the hazard indicator mode is set,
the hazard indicator flashes 3 times.
. When the hazard indicator and horn
mode is set, the hazard indicator
flashes once and the horn chirps once.
WARNING
To avoid risk of injury or death, do not use
the remote engine start function when the
vehicle is in an enclosed area such as a
garage.
JVP0437X
The remote engine start
button is on
the Intelligent Key if the vehicle has remote
engine start function. This function allows
the engine to start from outside the
vehicle.
Automatic climate control system will
automatically adjust the passenger compartment to be the set appropriate temperature when the remote engine start
function is used.
NOS1695
Laws in some local communities may
restrict the use of remote starters. For
example, some laws require a person using
remote start to have the vehicle in view.
Check local regulations for any require-
3-20 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(167,1)
ments.
Other conditions may affect the remote
engine start function. See “Conditions the
remote start will not work” (P.3-22).
Other conditions can affect the performance of the Intelligent Key transmitter.
See “Intelligent Key system” (P.3-6) for
additional information.
REMOTE ENGINE START OPERATING
RANGE CV37D1-EE638A15-663C-4C3E-8748-1E7A578339ED
The remote engine start function can only
be used when the Intelligent Key is within
the specified operating range from the
vehicle.
When the Intelligent Key battery is discharged or other strong radio wave sources
are present near the operating location,
the Intelligent Key operating range becomes narrower, and the Intelligent Key
may not function properly.
The remote engine start operating range is
approximately 197 ft (60 m) from the
vehicle.
REMOTE STARTING
THE ENGINE
CV37D1-A405E9BD-0C48-4DE5-945E-6F650CF352E4
“Driving the vehicle” (P.5-16).
To use the remote start function to start the
engine, perform the following:
EXTENDING
ENGINE RUN TIME
CV37D1-BA5C7406-D1DF-49A9-9254-BD60722F6D99
1. Aim the Intelligent Key at the vehicle.
2. Push the LOCK
doors.
button to lock all
3. Within 5 seconds push and hold the
remote engine start
button until
the turn signal lights flash and the tail
lights illuminate. If the vehicle is not
within view, push and hold the remote
engine start
button for at least 2
seconds.
The following events will occur when the
engine starts:
. The front parking lights will turn on and
remain on as long as the engine is
running.
. The doors will be locked and the air
conditioner system may turn on.
. The engine will continue to run for
about 10 minutes. Repeat the steps to
extend the time for an additional 10
minutes. See “Extending engine run
time” (P.3-21).
Depress and hold the brake pedal, then
place the ignition switch in the ON position
before driving. For further instructions, see
The remote engine start function can be
extended one time by performing the steps
listed in “Remote starting the engine” (P.321). Run time will be calculated as follows:
. The first 10 minute run time will start
when the remote engine start function
is performed.
. The second 10 minutes will start immediately when the remote engine start
function is performed. For example, if
the engine has been running for 5
minutes, and 10 minutes are added,
the engine will run for a total of 15
minutes.
. Extending engine run time will count
towards the two remote start limit.
A maximum of two remote starts, or a
single start with an extension, are allowed
between ignition cycles.
The ignition switch must be cycled to the
ON position and then back to the OFF
position before the remote engine start
procedure can be used again.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-21
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(168,1)
CANCELING
A REMOTE START
CV37D1-8BB90049-D5BB-4B6C-AA6D-EBF1DF2B034C
To cancel a remote start, perform one of the
following:
. Aim the Intelligent Key at the vehicle
and push and hold the remote engine
start
button until the parking lights
turn off.
. Turn on the hazard warning flashers.
. Cycle the ignition switch ON and then
OFF.
. The extended engine run time has
expired.
. The first 10 minute timer has expired.
. The engine hood has been opened.
. The shift lever is moved out of P (Park).
. The alarm sounds due to illegal entry
into the vehicle.
. The ignition switch is pushed without
an Intelligent Key in the vehicle.
. The ignition switch is pushed with an
Intelligent Key in the vehicle but the
brake pedal is not depressed.
CONDITIONS THE REMOTE START
WILL NOT CV37D1-6589D692-7771-420B-92D7-BFBEC600ED65
WORK
The remote start will not operate if any of
the following conditions are present:
. The ignition switch is placed in the ON
position.
. The hood is not securely closed.
. The hazard warning lights are on.
. The engine is still running. The engine
must be completely stopped. Wait at
least 6 seconds if the engine goes from
running to off. This is not applicable
when extending engine run time.
. The remote engine start
button is
not pushed and held for at least 2
seconds.
. The remote engine start
button is
not pushed and held within 5 seconds
of pushing LOCK
button.
. The brake pedal is depressed.
. The doors are not closed and locked.
. The trunk is open.
. The Intelligent Key warning message is
displayed in the vehicle information
display.
. The alarm sounds due to illegal entry
into the vehicle.
. Two remote vehicle starts, or a single
remote start with an extension, have
already been used.
. The vehicle is not in P (Park).
. The remote engine start function has
been switched to OFF in the settings
menu on the lower display. For additional information, see the Infiniti
InTouch Owner’s Manual.
The remote engine start may display a
warning or indicator in the vehicle information display. For an explanation of the
warning or indicator, see “Indicators for
operation” (P.2-24).
3-22 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(169,1)
HOOD
TRUNK LID
CV37D1-20C23685-3A25-458D-9288-A06E6D1493E3
CV37D1-75D000D4-1871-4E76-9E77-0069D49C3474
WARNING
JVP0452X
1
1. Pull the hood lock release handle *
located below the instrument panel;
the hood will then spring up slightly.
2 up at the front of the
2. Pull the lever *
hood with your fingertips and raise the
hood.
3. When closing the hood, slowly close
the hood down to latch both the right
and left locks. Push the hood down to
lock the hood securely into place.
.
Do not drive with the trunk lid open. This
could allow dangerous exhaust gases to
be drawn into the vehicle. See “Exhaust
gas (carbon monoxide)” (P.5-4) of this
manual.
.
Closely supervise children when they are
around cars to prevent them from playing and becoming locked in the trunk
where they could be seriously injured.
Keep the car locked, with the trunk
closed, when not in use, and prevent
children’s access to Intelligent Keys.
WARNING
.
Make sure the hood is completely closed
and latched before driving. Failure to do
so could cause the hood to fly open and
result in an accident.
.
If you see steam or smoke coming from
the engine compartment, to avoid injury
do not open the hood.
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-23
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(170,1)
TRUNK BUTTON
CV37D1-9543F3DF-A8B1-4A0A-869F-CB9540E9A670
The trunk lid can be opened by pushing the
TRUNK
button on the Intelligent Key for
more than 1 second.
The trunk lid can be opened by pushing the
A even if the
trunk open request switch *
Intelligent Key is not within the operating
range of the trunk lock/unlock function,
when all doors are unlocked by the power
door lock system, and the automatic
unlock function.
JVP0202X
JVP0451X
TRUNK LIDCV37D1-BD4F35A1-FCB4-479E-86E2-5B1E7DFB91EA
RELEASE SWITCH
TRUNK OPEN
REQUEST SWITCH
CV37D1-39096AF8-28CC-40D3-B593-D20291A58019
The trunk lid release switch
on the instrument panel.
The trunk lid can be opened by pushing the
A when the
trunk open request switch *
Intelligent Key is within the operating
range of the trunk lock/unlock function
regardless of the inside lock knob position.
A
*
is located
To open the trunk lid, push the release
switch. To close, push the trunk lid down.
(See “Remote keyless entry system” (P.316).)
The trunk lid can be opened by pushing the
A even if the
trunk open request switch *
Intelligent Key is not within the operating
range of the trunk lock/unlock function,
when all doors are unlocked by the power
door lock system, and the automatic
unlock function.
(See “Intelligent Key system” (P.3-6).)
3-24 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(171,1)
vehicle and the Intelligent Key with the
valet and keep the mechanical key with
you.
(See “Keys” (P.3-2).)
To connect the power to the trunk lid, push
B position.
the switch to the ON *
JVP0203X
JVP0460X
TRUNK RELEASE POWER CANCEL
SWITCH CV37D1-1A70330B-B9ED-4FE5-9A9B-488DA9429576
INTERIOR CV37D1-59AC0EC7-68A9-4148-8401-E6E5648452BA
TRUNK LID RELEASE
WARNING
When the switch located inside the glove
A , the power to
box is in the OFF position *
the trunk lid will be canceled and the trunk
lid cannot be opened by the trunk lid
release switch, the trunk open request
switch or the TRUNK button on the Intelligent Key.
Closely supervise children when they are
around cars to prevent them from playing
and becoming locked in the trunk where
they could be seriously injured. Keep the car
locked, with the trunk lid securely latched,
when not in use, and prevent children’s
access to Intelligent Keys.
When you have to leave the vehicle with a
valet and want to keep your belongings
safe in the glove box and the trunk, push
this switch to OFF and lock the glove box
with the mechanical key. Then leave the
The interior trunk lid release mechanism
allows opening of the trunk lid in the event
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-25
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(172,1)
FUEL-FILLER DOOR
CV37D1-8E71A60B-F833-43AF-9065-3F69ED17D7F7
. Push the power door lock switch to the
UNLOCK position.
To lock, close the fuel-filler door securely
and lock all doors by operating the door
handle request switch, the LOCK button on
the Intelligent Key, the mechanical key or
the power door lock switch.
that people become locked inside the
trunk.
Releasing CV37D1-BF7705B5-A805-4E0F-9078-D144861526D3
inside the trunk
To open the trunk lid from the inside, pull
1
the release handle *
until the lock
releases and push up on the trunk lid.
The release lever is made of a material that
glows in the dark after a brief exposure to
ambient light.
FUEL-FILLER
CAP
CV37D1-3BC658AF-A194-49C3-ACA0-3AB52617E0B0
WARNING
The handle is located on the back of the
trunk lid as illustrated.
JVP0461X
.
Gasoline is extremely flammable and
highly explosive under certain conditions. You could be burned or seriously
injured if it is misused or mishandled.
Always stop engine and do not smoke or
allow open flames or sparks near the
vehicle when refueling.
.
Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off
automatically. Continued refueling may
cause fuel overflow, resulting in fuel
spray and possibly a fire.
.
Use only an original equipment type
fuel-filler cap as a replacement. It has a
built-in safety valve needed for proper
operation of the fuel system and emission control system. An incorrect cap can
OPENINGCV37D1-2D0C6A2B-0D70-4CF5-ACF9-2F0CBE85CDCE
THE FUEL-FILLER DOOR
To open the fuel-filler door, unlock the fuelfiller door by using one of the following
operations, then push the upper left side of
A .
the door *
. Touch the one touch unlock sensor on
one of the door handles and then push
the door handle request switch while
carrying the Intelligent Key.
. Push the UNLOCK button on the Intelligent Key twice.
. Insert the mechanical key into the door
lock cylinder and turn it to the rear of
the vehicle twice.
3-26 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(173,1)
result in a serious malfunction and
possible injury. It could also cause the
Malfunction Indicator Light (MIL) to
come on.
.
Never pour fuel into the throttle body to
attempt to start your vehicle.
.
Do not fill a portable fuel container in the
vehicle or trailer. Static electricity can
cause an explosion of flammable liquid,
vapor or gas in any vehicle or trailer. To
reduce the risk of serious injury or death
when filling portable fuel containers:
damage.
.
— Always place the container on the
ground when filling.
— Do not use electronic devices when
filling.
.
— Keep the pump nozzle in contact
with the container while you are
filling it.
— Use only approved portable fuel
containers for flammable liquid.
.
CAUTION
.
Insert the cap straight into the fuel-filler
tube, then tighten the fuel-filler cap until
a single click is heard. Failure to tighten
the fuel-filler cap properly may cause the
Malfunction Indicator Light (MIL) to
illuminate. If the
light illuminates
because the fuel-filler cap is loose or
missing, tighten or install the cap and
continue to drive the vehicle. The
light should turn off after a few driving
trips. If the
light does not turn off
after a few driving trips, have the vehicle
inspected. It is recommended you visit
an INFINITI retailer for this service.
The Loose Fuel Cap warning will appear if
the fuel-filler cap is not properly tightened. It may take a few driving trips for
the warning to be displayed. Failure to
tighten the fuel-filler cap properly after
the Loose Fuel Cap warning appears may
cause the
Malfunction Indicator
Light (MIL) to illuminate.
For additional information, see “Malfunction Indicator Light (MIL)” (P.2-19).
JVP0454X
To remove the fuel-filler cap:
1. Turn the fuel-filler cap counterclockwise
to remove.
2. Put the fuel-filler cap on the cap holder
1 while refueling.
*
To install the fuel-filler cap:
1. Insert the fuel-filler cap straight into the
fuel-filler tube.
2. Turn the fuel-filler cap clockwise until a
single click is heard.
If fuel is spilled on the vehicle body,
flush it away with water to avoid paint
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(174,1)
TILT/TELESCOPIC STEERING
CV37D1-CEBF8919-BACA-45A0-AD5E-D7C5C540A80F
3. Push the
or
switch * on the
steering wheel for longer than 1 second
to turn off the Loose Fuel Cap warning
after tightening the fuel-filler cap.
A
JVP0455X
Loose FuelCV37D1-E828C7F2-5979-40B0-9072-E36A74010995
Cap warning
The Loose Fuel Cap warning appears in the
vehicle information display when the fuelfiller cap is not tightened correctly after the
vehicle has been refueled. It may take a
few driving trips for the warning to be
displayed.
WARNING
.
Do not adjust the steering wheel while
driving. You could lose control of your
vehicle and cause an accident.
.
Do not adjust the steering wheel any
closer to you than is necessary for
proper steering operation and comfort.
The driver’s air bag inflates with great
force. If you are unrestrained, leaning
forward, sitting sideways or out of
position in any way, you are at greater
risk of injury or death in a crash. You may
also receive serious or fatal injuries from
the air bag if you are up against it when
it inflates. Always sit back against the
seatback and as far away as practical
from the steering wheel. Always use the
seat belts.
To turn off the warning, perform the
following:
1. Remove and install the fuel-filler cap as
soon as possible. (See “Fuel-filler cap”
(P.3-26).)
2. Tighten the fuel-filler cap until a single
click is heard.
3-28 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(175,1)
SUN VISORS
CV37D1-98A8C030-88FE-4F0D-B879-CF82677626E9
SPA2328
JVP0205X
MANUAL OPERATION (if so
equipped)CV37D1-1FBC6099-D771-4AC6-A788-0B00E1852013
ELECTRIC OPERATION (if so
equipped)CV37D1-043E9C43-1598-497B-B427-D478DD3E9E4C
Tilt or telescopic
operation
CV37D1-4F8899B5-4789-4B55-B322-F9AA8F80D3B8
Tilt or telescopic
operation
CV37D1-2D699F18-28FA-4EF4-B7D7-12496FEE85FF
1 down and adjust the
Pull the lock lever *
steering wheel up, down, forward or rearward to the desired position.
Move the switch to adjust the steering
wheel up or down, forward or rearward to
the desired position.
Push the lock lever up securely to lock the
steering wheel in place.
SPA2471
1. To block glare from the front, swing
1 .
down the sun visor *
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-29
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(176,1)
MIRRORS
CV37D1-899C7DDA-DD40-4329-80A8-CE6DFE22FD97
2. To block glare from the side, remove
the sun visor from the center mount
2 .
and swing the visor to the side *
3 in or out as
3. Slide the sun visor *
needed (for driver’s side only).
SPA2447
INSIDE MIRROR
CV37D1-10BF6E9D-94BA-434D-B556-9F6B29EFE1E4
Adjust the height and the angle of the
inside mirror to the desired position.
SPA2143
Manual anti-glare
type
CV37D1-113B649A-A708-4CE0-8022-1A574F12DF57
1
The night position *
will reduce glare
from the headlights of vehicles behind you
at night.
Use the day position
daylight hours.
2
*
when driving in
WARNING
Use the night position only when necessary,
because it reduces rear view clarity.
3-30 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(177,1)
AutomaticCV37D1-544653BF-F3F0-4DF6-B343-B51FC6A721BA
anti-glare type
The inside mirror is designed so that it
automatically changes reflection according
to the intensity of the headlights of the
following vehicle.
The anti-glare system will be automatically
turned on when the ignition switch is
placed in the ON position.
The anti-glare system also operates for the
outside mirrors (if so equipped).
SPA2422A
Type A (if so equipped)
When the anti-glare system is turned on,
A will illuminate and
the indicator light *
excessive glare from the headlights of the
vehicle behind you will be reduced.
Type A (if so equipped): Push the
B to make the inside mirror
switch *
operate normally and the indicator light
B again
will turn off. Push the
switch *
to turn the system on.
operation.
For the compass (if so equipped) operation, see “Compass” (P.2-9).
For the HomeLink® Universal Transceiver (if
so equipped) operation, see “HomeLink®
Universal Transceiver” (P.2-62).
OUTSIDE MIRRORS
CV37D1-0D342898-430F-456A-9040-9578417F2830
WARNING
Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident. Use
the inside mirror or glance over your
shoulder to properly judge distances to
other objects.
Type B (if so equipped): Push the “*”
C
switch *
to make the inside mirror
operate normally. The indicator light will
D to turn the
turn off. Push the “I” switch *
system on.
SPA2450
Type B (if so equipped)
Do not allow any object to cover the
E
sensors *
or apply glass cleaner on
them. Doing so will reduce the sensitivity
of the sensor, resulting in improper
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-31
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(178,1)
3. Select the right or left side mirror by
operating the outside mirror control
switch.
4. The outside mirror surface moves
downward.
When one of the following conditions has
occurred, the outside mirror surface will
return to its original position.
JVP0246X
SPA1829
. The shift lever is moved to any position
other than R (Reverse).
. The outside mirror control switch is set
to the center position.
. The ignition switch is pushed to the OFF
position.
AdjustingCV37D1-0B4E65C5-2077-45A9-98FC-A8E07B696D9B
outside mirrors
Foldable outside
mirrors
CV37D1-25F8CC36-EC21-493D-ABB8-F73A7158209E
The outside mirror control switch is located
on the driver’s armrest.
Fold the outside mirror by pushing it
toward the rear of the vehicle.
Automatic anti-glare (if so
equipped)CV37D1-91655C78-1391-4C73-AE8D-F7830B95A06E
The outside mirror will operate only when
the ignition switch is in the ACC or ON
position.
Reverse tilt-down feature (if so
equipped)CV37D1-3922E781-5D55-4D69-925C-6C97E4BD6F11
The outside mirrors are designed so that
they automatically change reflection according to the intensity of the headlights of
the vehicle following you.
1 right or left to select
Move the switch *
the right or left side mirror, then adjust
2 .
using the control switch *
DefrostingCV37D1-16A73C41-5F8D-482E-96CB-1F7AF0A050F6
outside mirrors
The outside mirrors will be heated when
the rear window defroster switch is operated.
When backing up the vehicle, the right and
left outside mirrors will turn downward
automatically to provide better rear visibility.
1. Push the ignition switch to the ON
position.
The anti-glare system will be automatically
turned on when the ignition switch is
placed in the ON position.
2. Move the shift lever to the R (Reverse)
position.
3-32 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(179,1)
AUTOMATIC DRIVE POSITIONER (if so
equipped)
CV37D1-E450D796-08F9-4562-8F47-BFC4EB16402B
The automatic drive positioner system has
a memory storage function.
SIC3869
JVP0462X
VANITY MIRROR
CV37D1-9AE2DF89-3765-4965-AB82-63AC485FF71B
MEMORY CV37D1-C3253FC6-067F-4EF6-AC8E-443DBC2A82D7
STORAGE
To use the front vanity mirror, pull down
the sun visor and pull up the cover.
Two positions for the driver’s seat, steering
column and outside mirrors can be stored
in the automatic drive positioner memory.
Follow these procedures to use the memory system.
1. Adjust the driver’s seat, steering column and outside mirrors to the desired
positions by manually operating each
adjusting switch. For additional information, see “Seats” (P.1-2), “Tilt/telescopic steering” (P.3-28) and “Outside
mirrors” (P.3-31).
Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
3-33
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(180,1)
2. Push the SET switch and, within 5
seconds, push the memory switch (1
or 2) fully for at least 1 second.
orized position with the indicator light
flashing, and then the light will stay on
for approximately 5 seconds.
The indicator light for the pushed
memory switch will stay on for approximately 5 seconds after pushing the
switch.
Linking log-in function to a stored
memory position
CV37D1-AB3F7AAC-59C4-4119-9D25-7D847B211DA2
When the memory is stored in the
memory switch (1 or 2), a buzzer will
sound.
If memory is stored in the same
memory switch, the previous memory
will be deleted.
Confirming
memory storage
CV37D1-CE2091ED-9082-42A3-AC8C-4E5B88DA32AD
Push the SET switch. If the main memory
has not been stored, the indicator light will
come on for approximately 0.5 seconds.
When the memory has stored in position,
the indicator light will stay on for approximately 5 seconds.
Selecting CV37D1-812ACCF7-5E50-4166-B150-60EB8EB9A549
the memorized position
1. Move the shift lever to the P (Park)
position.
2. Push the memory switch (1 or 2) fully
for at least 1 second.
The log-in function can be linked to a
stored memory position with the following
procedure.
1. Place the ignition switch in the ON
position while carrying an Intelligent
Key that was registered to the vehicle
with the log-in function. For more
details, see “Log-in function” (P.3-16).
2. Adjust the position of the driver’s seat,
steering column and outside mirrors
manually. See “Seats” (P.1-2), “Tilt/
telescopic steering” (P.3-28) and “Outside mirrors” (P.3-31).
SYSTEM OPERATION
CV37D1-4CE0BF2D-D72F-4384-A8B7-B5B43A28A6A7
The automatic drive positioner system will
not work or will stop operating under the
following conditions:
. When the vehicle is moving.
. When the adjusting switch for the
driver’s seat and steering column is
turned on while the automatic drive
positioner is operating.
. When the memory switch 1 or 2 is
pushed for less than 1 second.
. When the seat, steering column and
outside mirrors have already been
moved to the memorized position.
. When no position is stored in the
memory switch.
. While the walk-in function operates.
3. Place the ignition switch in the OFF
position.
The next time you log in (selecting the user
on the display) after placing the ignition
switch in the ON position while carrying the
Intelligent Key, the system will automatically adjust to the memorized driving
position.
The driver’s seat, steering column and
outside mirrors will move to the mem-
3-34 Pre-driving checks and adjustments
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(181,1)
4 Monitor, climate, audio, phone and voice recognition systems
Infiniti InTouch Owner’s Manual ..........................
...
4-2
Ventilators ..........................................................
...
4-2
Condition:
Antenna .............................................................
...
Window antenna ...........................................
...
Satellite antenna ..........................................
...
Car phone or CB radio ........................................
...
[ Edit: 2016/ 4/ 27
4-3
4-3
4-3
4-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(182,1)
INFINITI INTOUCH OWNER’S MANUAL
CV37D1-B23392E9-708E-4759-9035-EA232159AFA6
VENTILATORS
CV37D1-A6C0DC71-8A00-4DE2-9C56-DCE4B7D79C9B
Refer to the Infiniti InTouch Owner’s
Manual that includes the following information.
.
.
.
.
.
.
.
.
.
.
.
Infiniti InTouch
Navigation system (if so equipped)
Audio system
Bluetooth® Hands-Free Phone system
Heater and air conditioner
Viewing information
Other settings
Voice recognition (if so equipped)
Monitor system
Meter settings
General system information
Open or close, and adjust the air flow
direction of ventilators.
: This symbol indicates that the ventilators are
closed.
: This symbol indicates that the ventilators are
open.
JVH0510X
Center ventilators
JVH0511X
Side ventilators
4-2 Monitor, climate, audio, phone and voice recognition systems
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(183,1)
ANTENNA
CAR PHONE OR CB RADIO
CV37D1-AA6717FA-10E0-42FB-8732-159E42912C62
CV37D1-E9BECCF4-3B65-43D2-8E0D-735F8E433350
WINDOW CV37D1-F0F5E74C-1AB3-4913-82C2-E7CF1AB42BBC
ANTENNA
When installing a car phone or a CB radio
in your vehicle, be sure to observe the
following cautions, otherwise the new
equipment may adversely affect the electronic control modules and electronic control system harness.
The antenna pattern is printed inside the
rear window.
CAUTION
.
.
Do not place metalized film near the rear
window glass or attach any metal parts
to it. This may cause poor reception or
noise.
When cleaning the inside of the rear
window, be careful not to scratch or
damage the rear window antenna.
Lightly wipe along the antenna with a
dampened soft cloth.
WARNING
.
A cellular phone should not be used for
any purpose while driving so full attention may be given to vehicle operation.
Some jurisdictions prohibit the use of
cellular phones while driving.
.
If you must make a call while your
vehicle is in motion, the hands-free
cellular phone operational mode (if so
equipped) is highly recommended. Exercise extreme caution at all times so full
attention may be given to vehicle operation.
.
If a conversation in a moving vehicle
requires you to take notes, pull off the
road to a safe location and stop your
vehicle before doing so.
JVH0641X
SATELLITE CV37D1-B7B9A80D-785A-4F35-94F8-20E8F22760C4
ANTENNA
There is a satellite antenna on the rear part
of the vehicle roof.
A buildup of ice on the satellite radio
antenna can affect satellite radio performance. Remove the ice to restore satellite
radio reception.
Monitor, climate, audio, phone and voice recognition systems
Condition:
[ Edit: 2016/ 4/ 27
4-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(184,1)
CAUTION
.
Keep the antenna as far away as
possible from the electronic control
modules.
.
Keep the antenna wire more than 8 in (20
cm) away from the electronic control
system harness. Do not route the antenna wire next to any harness.
.
Adjust the antenna standing-wave ratio
as recommended by the manufacturer.
.
Connect the ground wire from the CB
radio chassis to the body.
.
For details, it is recommended you visit
an INFINITI retailer.
4-4
Monitor, climate, audio, phone and voice recognition systems
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(185,1)
5 Starting and driving
Precautions when starting and driving ................
...
5-4
Exhaust gas (carbon monoxide) ......................
...
5-4
Three-way catalyst ..........................................
...
5-5
Tire Pressure Monitoring System (TPMS) .........
...
5-5
Avoiding collision and rollover ........................
...
5-9
Off-road recovery ............................................
...
5-9
Rapid air pressure loss .................................
...
5-10
Drinking alcohol/drugs and driving ...............
...
5-11
Intelligent All-Wheel Drive (AWD) driving
safety precautions (AWD models) ..................
...
5-11
Push-button ignition switch ..............................
...
5-12
Operating range for engine start function .....
... 5-12
Push-button ignition switch operation ..........
...
5-13
Push-button ignition switch positions ...........
...
5-13
Emergency engine shut off ...........................
...
5-14
Intelligent Key battery discharge ..................
...
5-14
Before starting the engine ................................
...
5-15
Starting the engine ...........................................
...
5-15
Remote start (if so equipped) .......................
...
5-16
Driving the vehicle ............................................
...
5-16
Automatic Transmission (AT) .........................
...
5-16
Parking brake ...................................................
...
5-22
INFINITI Drive Mode Selector .............................
...
5-23
STANDARD mode ..........................................
...
5-23
SPORT+ mode (if so equipped) .....................
...
5-23
Condition:
SPORT mode ...............................................
...
SNOW mode ...............................................
...
ECO mode (if so equipped) ..........................
...
PERSONAL mode .........................................
...
Active Lane Control (if so equipped) .................
...
Active Lane Control operation .....................
...
Turning Active Lane Control ON/OFF ............
...
How to enable/disable Active
Lane Control ...............................................
...
Active Lane Control limitations ....................
...
System temporarily unavailable ..................
...
System malfunction ....................................
...
System maintenance ...................................
...
Lane Departure Warning (LDW) system/Lane
Departure Prevention (LDP) (if so equipped) .....
...
LDW system operation ................................
...
How to enable/disable the LDW system ......
...
LDP system operation .................................
...
Turning the LDP system ON/OFF ..................
...
How to enable/disable the LDP system .......
...
LDW/LDP system limitations .......................
...
System temporarily unavailable ..................
...
System malfunction ....................................
...
System maintenance ...................................
...
[ Edit: 2016/ 4/ 27
5-24
5-24
5-24
5-26
5-27
5-29
5-30
5-31
5-32
5-33
5-34
5-34
5-35
5-37
5-37
5-37
5-38
5-39
5-39
5-41
5-41
5-42
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(186,1)
Blind Spot Warning (BSW) (if so equipped) .......
...
BSW system operation ..................................
...
How to enable/disable the BSW system ........
...
BSW system limitations ................................
...
BSW driving situations .................................
...
System temporarily unavailable ....................
...
System malfunction ......................................
...
System maintenance ....................................
...
Blind Spot Intervention® (BSI) (if
so equipped) ....................................................
...
BSI system operation ...................................
...
Turning the BSI system ON/OFF ....................
...
How to enable/disable the BSI system .........
...
BSI system limitations ..................................
...
BSI driving situations ...................................
...
System temporarily unavailable ....................
...
System malfunction ......................................
...
System maintenance ....................................
...
Back-up Collision Intervention (BCI) (if
so equipped) ....................................................
...
BCI system operation ...................................
...
Turning the BCI system ON/OFF ....................
...
How to enable/disable the BCI system .........
...
BCI system limitations ..................................
...
System temporarily unavailable ....................
...
System malfunction ......................................
...
System maintenance ....................................
...
Cruise control (if so equipped) ..........................
...
Precautions on cruise control .......................
...
Condition:
5-42
5-44
5-45
5-45
5-46
5-49
5-49
5-49
5-50
5-52
5-53
5-54
5-54
5-56
5-61
5-61
5-62
5-63
5-65
5-69
5-70
5-71
5-72
5-73
5-73
5-74
5-74
Cruise control operations ............................
...
5-75
Intelligent Cruise Control (ICC) (if
so equipped) ....................................................
...
5-76
How to select the cruise control mode ........
...
5-78
Vehicle-to-vehicle distance control mode .....
... 5-78
Conventional (fixed speed) cruise
control mode ..............................................
...
5-92
Distance Control Assist (DCA) (if so equipped) ... 5-96
DCA system operation .................................
...
5-98
Turning the DCA system ON/OFF ...............
...
5-101
How to enable/disable the DCA system .....
... 5-102
DCA system display and indicators ...........
...
5-102
DCA system limitations .............................
...
5-103
System temporarily unavailable ................
...
5-105
System malfunction ..................................
...
5-106
System maintenance .................................
...
5-106
Forward Emergency Braking (FEB) system (if
so equipped) ..................................................
...
5-107
FEB system operation ................................
...
5-108
Turning the FEB system ON/OFF ................
...
5-110
FEB system limitations ..............................
...
5-111
System temporarily unavailable ................
...
5-113
System malfunction ..................................
...
5-114
System maintenance .................................
...
5-115
Predictive Forward Collision Warning (PFCW)
(if so equipped) ..............................................
...
5-116
PFCW system operation .............................
...
5-118
Turning the PFCW system ON/OFF .............
...
5-119
PFCW system limitations ...........................
...
5-121
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(187,1)
System temporarily unavailable ..................
...
System malfunction ....................................
...
System maintenance ..................................
...
Break-in schedule ...........................................
...
Fuel Efficient Driving Tips ................................
...
Increasing fuel economy .................................
...
Intelligent All-Wheel Drive (AWD) (if
so equipped) ..................................................
...
Parking/parking on hills .................................
...
Power steering ................................................
...
Electric power steering type ........................
...
Hydraulic pump electric power
steering type ..............................................
...
Direct Adaptive Steering type .....................
...
Brake system ..................................................
...
Braking precautions ...................................
...
Parking brake break-in ...............................
...
Brake assist ....................................................
...
Brake assist ...............................................
...
Anti-lock Braking System (ABS) ..................
...
Vehicle Dynamic Control (VDC) system ............
...
Brake force distribution ..............................
...
Condition:
5-123
5-123
5-124
5-125
5-125
5-126
5-127
5-129
5-130
5-130
5-131
5-131
5-133
5-133
5-134
5-134
5-134
5-134
5-136
5-137
Active trace control ........................................
...
Hill Start Assist system ..................................
...
Chassis control ..............................................
...
Idling Stop System (if so equipped) ................
...
Retrograde movement control function ......
...
Idling Stop System display ........................
...
Idling Stop OFF switch ..............................
...
Cold weather driving ......................................
...
Freeing a frozen door lock .........................
...
Antifreeze .................................................
...
Battery ......................................................
...
Draining of coolant water ..........................
...
Tire equipment ..........................................
...
Special winter equipment .........................
...
Driving on snow or ice ..............................
...
Engine block heater (if so equipped) .........
...
Active noise cancellation/Active
sound enhancement .......................................
...
Active noise cancellation ...........................
...
Active sound enhancement .......................
...
[ Edit: 2016/ 4/ 27
5-138
5-139
5-140
5-140
5-142
5-142
5-144
5-145
5-145
5-145
5-145
5-145
5-145
5-146
5-146
5-146
5-147
5-148
5-148
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(188,1)
PRECAUTIONS WHEN STARTING AND
DRIVING
CV37D1-5E9F6826-E366-4CA8-A25F-30A9D8D41D04
WARNING
.
.
Do not leave children or adults who
would normally require the support of
others alone in your vehicle. Pets should
not be left alone either. They could
accidentally injure themselves or others
through inadvertent operation of the
vehicle. Also, on hot, sunny days,
temperatures in a closed vehicle could
quickly become high enough to cause
severe or possibly fatal injuries to
people or animals.
Closely supervise children when they are
around cars to prevent them from playing and becoming locked in the trunk
where they could be seriously injured.
Keep the car locked, with the rear
seatback and trunk lid securely latched
when not in use, and prevent children’s
access to car keys.
EXHAUST CV37D1-BD7897F9-A61E-41DB-ADF1-D5A23F7D7029
GAS (carbon monoxide)
.
If electrical wiring or other cable connections must pass to a trailer through
the seal on the trunk lid or the body,
follow the manufacturer’s recommendation to prevent carbon monoxide entry
into the vehicle.
.
The exhaust system and body should be
inspected by a qualified mechanic whenever:
WARNING
.
.
Do not breathe exhaust gases; they
contain colorless and odorless carbon
monoxide. Carbon monoxide is dangerous. It can cause unconsciousness or
death.
If you suspect that exhaust fumes are
entering the vehicle, drive with all
windows fully open, and have the vehicle
inspected immediately.
.
Do not run the engine in closed spaces
such as a garage.
.
Do not park the vehicle with the engine
running for any extended length of time.
.
Keep the trunk lid closed while driving,
otherwise exhaust gases could be drawn
into the passenger compartment. If you
must drive with the trunk lid open, follow
these precautions:
— The vehicle is raised for service.
— You suspect that exhaust fumes are
entering into the passenger compartment.
— You notice a change in the sound of
the exhaust system.
— You have had an accident involving
damage to the exhaust system,
underbody, or rear of the vehicle.
1) Open all the windows.
2) Set the air recirculation to off and
the fan control to high to circulate
the air.
5-4
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(189,1)
THREE-WAY
CATALYST
CV37D1-7B30066F-F327-4FBC-9926-F97EA49A5335
flow into the three-way catalyst, causing
it to overheat. Do not keep driving if the
engine misfires, or if noticeable loss of
performance or other unusual operating
conditions are detected. Have the vehicle
inspected promptly. It is recommended
you visit an INFINITI retailer for this
service.
The three-way catalyst is an emission
control device installed in the exhaust
system. Exhaust gases in the three-way
catalyst are burned at high temperatures to
help reduce pollutants.
WARNING
.
.
The exhaust gas and the exhaust system
are very hot. Keep people, animals or
flammable materials away from the
exhaust system components.
Do not stop or park the vehicle over
flammable materials such as dry grass,
waste paper or rags. They may ignite and
cause a fire.
CAUTION
.
Do not use leaded gasoline. Deposits
from leaded gasoline seriously reduce
the three-way catalyst’s ability to help
reduce exhaust pollutants.
.
Keep your engine tuned up. Malfunctions
in the ignition, fuel injection, or electrical systems can cause overrich fuel
.
Avoid driving with an extremely low fuel
level. Running out of fuel could cause the
engine to misfire, damaging the threeway catalyst.
.
Do not race the engine while warming it
up.
.
Do not push or tow your vehicle to start
the engine.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
CV37D1-7446E60A-99AE-4231-B060-531A4A4212AC
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recommended by the vehicle manufacturer on the
vehicle placard or tire inflation pressure
label. (If your vehicle has tires of a different
size than the size indicated on the vehicle
placard or tire inflation pressure label, you
should determine the proper tire inflation
pressure for those tires.)
As an added safety feature, your vehicle
has been equipped with a Tire Pressure
Monitoring System (TPMS) that illuminates
a low tire pressure telltale when one or
more of your tires is significantly underinflated. Accordingly, when the low tire
pressure telltale illuminates, you should
stop and check your tires as soon as
possible, and inflate them to the proper
pressure. Driving on a significantly underinflated tire causes the tire to overheat and
can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and
stopping ability.
For models with run-flat tires, if the vehicle
is being driven with one or more flat tires,
the low tire pressure warning light will
illuminate continuously and a chime will
sound for 10 seconds. The flat tire warning
will also appear in the vehicle information
display. The chime will only sound at the
first indication of a flat tire, and the
warning light will illuminate continuously.
When the flat tire warning is activated, it is
recommended you have the system reset
and the tire checked and replaced if
necessary by an INFINITI retailer. Even if
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(190,1)
the tire is inflated to the specified COLD tire
pressure, the warning light will continue to
illuminate until the system is reset by an
INFINITI retailer. Your vehicle can be driven
for a limited time on a flat tire. See “Runflat tires” (P.8-40).
Please note that the TPMS is not a
substitute for proper tire maintenance,
and it is the driver’s responsibility to
maintain correct tire pressure, even if
under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is combined with the low tire pressure telltale.
When the system detects a malfunction,
the telltale will flash for approximately one
minute and then remain continuously
illuminated. This sequence will continue
upon subsequent vehicle start-ups as long
as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low
tire pressure as intended. TPMS malfunctions may occur for a variety of reasons,
including the installation of replacement or
5-6
alternate tires or wheels on the vehicle that
prevent the TPMS from functioning properly. Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the
replacement or alternate tires and wheels
allow the TPMS to continue to function
properly.
AdditionalCV37D1-E2788307-A48C-48C5-80A6-AA66F3015BBF
information
. Since the spare tire (if so equipped) is
not equipped with the TPMS, the TPMS
does not monitor the tire pressure of
the spare tire.
. The TPMS will activate only when the
vehicle is driven at speeds above 16
MPH (25 km/h). Also, this system may
not detect a sudden drop in tire
pressure (for example a flat tire while
driving).
. The low tire pressure warning light does
not automatically turn off when the tire
pressure is adjusted. After the tire is
inflated to the recommended pressure,
the vehicle must be driven at speeds
above 16 MPH (25 km/h) to activate the
TPMS and turn off the low tire pressure
warning light. Use a tire pressure gauge
to check the tire pressure.
. The “Tire Pressure Low - Add Air”
warning appears in the vehicle information display when the low tire pressure
warning light is illuminated and low tire
pressure is detected. The “Tire Pressure
Low - Add Air” warning turns off when
the low tire pressure warning light
turns off.
The “Tire Pressure Low - Add Air”
warning does not appear if the low tire
pressure warning light illuminates to
indicate a TPMS malfunction.
. The “Flat Tire - Visit dealer” warning (if
so equipped) appears in the vehicle
information display when the low tire
pressure warning light is illuminated
and one or more flat tires are detected.
. Tire pressure rises and falls depending
on the heat caused by the vehicle’s
operation and the outside temperature.
Do not reduce the tire pressure after
driving because the tire pressure rises
after driving. Low outside temperature
can lower the temperature of the air
inside the tire which can cause a lower
tire inflation pressure. This may cause
the low tire pressure warning light to
illuminate. If the warning light illuminates in low ambient temperature,
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(191,1)
check the tire pressure for all four tires.
. You can also check the pressure of all
tires (except the spare tire) in the
vehicle information display. (See “Vehicle information display” (P.2-21).)
. After the ignition switch is placed in the
ON position, it may take a period of
time for the tire pressure to be displayed while the vehicle is driven.
Depending on the radio wave circumstance, tire pressure may not correctly
be displayed.
For additional information, see “Low tire
pressure warning light” (P.2-14) and “Tire
Pressure Monitoring System (TPMS)” (P.63).
reduce vehicle speed, pull off the road to
a safe location and stop the vehicle as
soon as possible. Driving with underinflated tires may permanently damage
the tires and increase the likelihood of
tire failure. Serious vehicle damage
could occur and may lead to an accident
and could result in serious personal
injury. Check the tire pressure for all
four tires. Adjust the tire pressure to the
recommended COLD tire pressure shown
on the Tire and Loading Information
label to turn the low tire pressure
warning light OFF. If the light still
illuminates while driving after adjusting
the tire pressure, a tire may be flat or the
TPMS may be malfunctioning. If you
have a flat tire, replace it with a spare
tire (if so equipped) as soon as possible.
If no tire is flat and all tires are properly
inflated, it is recommended you consult
an INFINITI retailer.
WARNING
.
.
Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufacturer for the possible influences before
use.
If the low tire pressure warning light
illuminates while driving, avoid sudden
steering maneuvers or abrupt braking,
.
For models with run-flat tires, although
you can continue driving with a punctured run-flat tire, remember that vehicle
handling stability is reduced, which
could lead to an accident and personal
injury. Also, driving a long distance at
high speeds may damage the tires.
— Do not drive at speeds above 50
MPH (80 km/h) and do not drive more
than approximately 93 miles (150
km) with a punctured run-flat tire.
The actual distance the vehicle can
be driven on a flat tire depends on
outside temperature, vehicle load,
road conditions and other factors.
— If you detect any unusual sounds or
vibrations while driving with a punctured run-flat tire, pull off the road to
a safe location and stop the vehicle
as soon as possible. The tire may be
seriously damaged and need to be
replaced.
.
Since the spare tire is not equipped with
the TPMS, when a spare tire is mounted
or a wheel is replaced, the TPMS will not
function and the low tire pressure warning light will flash for approximately 1
minute. The light will remain on after 1
minute. Have your tires replaced and/or
TPMS system reset as soon as possible.
It is recommended you visit an INFINITI
retailer for these services.
.
Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(192,1)
.
Do not inject any tire liquid or aerosol
tire sealant into the tires, as this may
cause a malfunction of the tire pressure
sensors.
CAUTION
.
The TPMS may not function properly
when the wheels are equipped with tire
chains or the wheels are buried in snow.
.
Do not place metalized film or any metal
parts (antenna, etc.) on the windows.
This may cause poor reception of the
signals from the tire pressure sensors,
and the TPMS will not function properly.
Some devices and transmitters may temporarily interfere with the operation of the
TPMS and cause the low tire pressure
warning light to illuminate. Some examples are:
. Facilities or electric devices using similar radio frequencies are near the
vehicle.
. If a transmitter set to similar frequencies is being used in or near the
vehicle.
5-8
. If a computer (or similar equipment) or a
DC/AC converter is being used in or
near the vehicle.
Low tire pressure warning light may
illuminate in the following cases.
For Canada:
. If the vehicle is equipped with a wheel
and tire without TPMS.
. If the TPMS has been replaced and the
ID has not been registered.
. If the wheel is not originally specified by
INFINITI.
FCC Notice:
1. This device may not cause interference,
and
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
2. This device must accept any interference, include interference that may
cause undesired operation of the device.
TPMS with
Tire Inflation Indicator
CV37D1-B54A1350-C92D-4F6C-87E5-812C6557D908
When adding air to an under-inflated tire,
the TPMS with Tire Inflation Indicator
provides visual and audible signals outside the vehicle to help you inflate the tires
to the recommended COLD tire pressure.
Vehicle set-up:
CV37D1-8FF7804B-C531-4018-9DA1-C1B0B3DA6368
1. Park the vehicle in a safe and level
place.
2. Apply the parking brake and place the
shift lever in the P (Park) position.
3. Place the ignition switch in the ON
position. Do not start the engine.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(193,1)
Operation: CV37D1-7C8EBB08-8038-4767-BB53-E776AF711CA6
1. Add air to the tire.
2. After a few seconds, the hazard indicators will start flashing.
3. When the designated pressure is
reached, the horn beeps once and the
hazard indicators stop flashing.
4. Perform the above steps for each tire.
. If the tire is over-inflated more than
approximately 4 psi (30 kPa), the horn
beeps and the hazard indicators flash 3
times. To correct the pressure, push the
core of the valve stem on the tire briefly
to release pressure. When the pressure
reaches the designated pressure, the
horn beeps once.
. If the hazard indicator does not flash
within approximately 15 seconds after
starting to inflate the tire, it indicates
that the Tire Inflation Indicator is not
operating.
. The TPMS will not activate the Tire
Inflation Indicator under the following
conditions:
— If there is interference from an
external device or transmitter
— The air pressure from the inflation
device such as those using a power
socket is not sufficient to inflate the
tire
— If an electrical equipment is being
used in or near the vehicle
— There is a malfunction in the TPMS
system
— There is a malfunction in the horn or
hazard indicators
. If the Tire Inflation Indicator does not
operate due to TPMS interference,
move the vehicle about 3 ft (1 m)
backward or forward and try again.
If the Tire Inflation Indicator is not working,
use a tire pressure gauge.
these driving practices could cause you to
lose control of your vehicle. As with any
vehicle, a loss of control could result in a
collision with other vehicles or objects, or
cause the vehicle to rollover, particularly if
the loss of control causes the vehicle to
slide sideways. Be attentive at all times,
and avoid driving when tired. Never drive
when under the influence of alcohol or
drugs (including prescription or over-thecounter drugs which may cause drowsiness). Always wear your seat belt as
outlined in the “Seat belts” (P.1-11) of this
manual, and also instruct your passengers
to do so.
AVOIDING COLLISION AND ROLLOVER
CV37D1-047D32A6-0EE4-4F7F-B9F8-E8B12A40EE94
Seat belts help reduce the risk of injury in
collisions and rollovers. In a rollover crash,
an unbelted or improperly belted person is
significantly more likely to be injured or
killed than a person properly wearing a
seat belt.
WARNING
Failure to operate this vehicle in a safe and
prudent manner may result in loss of control
or an accident.
Be alert and drive defensively at all times.
Obey all traffic regulations. Avoid excessive speed, high speed cornering, or
sudden steering maneuvers, because
OFF-ROADCV37D1-F5A6BE1D-A9F3-43EF-861B-3D13D68A61FE
RECOVERY
If driving the right side or left side wheels
may unintentionally leave the road surface.
Maintain control of the vehicle by following
the procedure below. Please note that this
procedure is only a general guide. The
vehicle must be driven as appropriate
based on the conditions of the vehicle,
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(194,1)
road and traffic.
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering
wheel with both hands and try to hold a
straight course.
4. When appropriate, slowly release the
accelerator pedal to gradually slow the
vehicle.
5. If there is nothing in the way, steer the
vehicle to follow the road while the
vehicle speed is reduced. Do not
attempt to drive the vehicle back onto
the road surface until vehicle speed is
reduced.
6. When it is safe to do so, gradually turn
the steering wheel until both tires
return to the road surface. When all
tires are on the road surface, steer the
vehicle to stay in the appropriate
driving lane.
. If you decide that it is not safe to
return the vehicle to the road surface
based on vehicle, road or traffic
conditions, gradually slow the vehicle to a stop in a safe place off the
road.
RAPID AIRCV37D1-16543328-232A-49F0-A2DA-1929AFAB3A39
PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged
due to hitting a curb or pothole. Rapid air
pressure loss can also be caused by driving
on under-inflated tires.
Rapid air pressure loss can affect the
handling and stability of the vehicle,
especially at highway speeds.
Help prevent rapid air pressure loss by
maintaining the correct air pressure and
visually inspect the tires for wear and
damage. See “Wheels and tires” (P.8-33) of
this manual.
If a tire rapidly loses air pressure or
“blows-out” while driving maintain control
of the vehicle by following the procedure
below. Please note that this procedure is
only a general guide. The vehicle must be
driven as appropriate based on the conditions of the vehicle, road and traffic.
WARNING
The following actions can increase the
chance of losing control of the vehicle if
there is a sudden loss of tire air pressure.
Losing control of the vehicle may cause a
collision and result in personal injury.
.
The vehicle generally moves or pulls in
the direction of the flat tire.
.
Do not rapidly apply the brakes.
.
Do not rapidly release the accelerator
pedal.
.
Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering
wheel with both hands and try to hold a
straight course.
3. When appropriate, slowly release the
accelerator pedal to gradually slow the
vehicle.
4. Gradually steer the vehicle to a safe
location off the road and away from
traffic if possible.
5. Lightly apply the brake pedal to gradually stop the vehicle.
6. Turn on the hazard warning flashers
and either contact a roadside emergency service to change the tire or see
“Changing a flat tire” (P.6-4) of this
Owner’s Manual.
5-10 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(195,1)
DRINKING ALCOHOL/DRUGS AND
DRIVING CV37D1-13296C69-D1F5-4782-BD1E-984365D4687A
WARNING
Never drive under the influence of alcohol or
drugs. Alcohol in the bloodstream reduces
coordination, delays reaction time and impairs judgement. Driving after drinking
alcohol increases the likelihood of being
involved in an accident injuring yourself and
others. Additionally, if you are injured in an
accident, alcohol can increase the severity
of the injury.
INFINITI is committed to safe driving.
However, you must choose not to drive
under the influence of alcohol. Every year
thousands of people are injured or killed in
alcohol-related accidents. Although the
local laws vary on what is considered to
be legally intoxicated, the fact is that
alcohol affects all people differently and
most people underestimate the effects of
alcohol.
Remember, drinking and driving don’t mix!
And that is true for drugs, too (over-thecounter, prescription, and illegal drugs).
Don’t drive if your ability to operate your
vehicle is impaired by alcohol, drugs, or
some other physical condition.
ground and shift the transmission to
any D (Drive) or R (Reverse) position with
the engine running. Doing so may result
in drivetrain damage or unexpected
vehicle movement which could result in
serious vehicle damage or personal
injury.
INTELLIGENT ALL-WHEEL DRIVE
(AWD) DRIVING SAFETY PRECAUTIONS (AWD
models)
CV37D1-08E06FA9-D35F-46BB-B430-9A69FFC70C4E
WARNING
.
Do not drive beyond the performance
capability of the tires, even with Intelligent AWD engaged. Accelerating
quickly, sharp steering maneuvers or
sudden braking may cause loss of
control.
.
Always use tires of the same type, size,
brand, construction (bias, bias-belted or
radial), and tread pattern on all four
wheels. Install tire chains on the rear
wheels when driving on slippery roads
and drive carefully.
.
This vehicle is not designed for off-road
(rough road) use. Do not drive on sandy
or muddy roads that tires may get stuck
in.
.
For AWD equipped vehicles, do not
attempt to raise two wheels off the
.
Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer (such
as the dynamometers used by some
states for emissions testing), or similar
equipment even if the other two wheels
are raised off the ground. Make sure you
inform test facility personnel that your
vehicle is equipped with AWD before it is
placed on a dynamometer. Using the
wrong test equipment may result in
drivetrain damage or unexpected vehicle
movement which could result in serious
vehicle damage or personal injury.
.
When a wheel is off the ground due to an
unlevel surface, do not spin the wheel
excessively.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(196,1)
PUSH-BUTTON IGNITION SWITCH
CV37D1-38A89CFD-17FC-46DB-99D0-3B34CBA9539B
someone who does not carry the Intelligent
Key, to push the ignition switch to start the
engine.
WARNING
Do not operate the push-button ignition
switch while driving the vehicle except in an
emergency. (The engine will stop when the
ignition switch is pushed 3 consecutive
times or the ignition switch is pushed and
held for more than 2 seconds.) If the engine
stops while the vehicle is being driven, this
could lead to a crash and serious injury.
Before operating the push-button ignition
switch, be sure to move the shift lever to
the P (Park) position.
SSD0872
. The trunk area is not included in the
operating range but the Intelligent Key
may function.
. If the Intelligent Key is placed on the
instrument panel, rear parcel shelf,
inside the glove box or door pocket,
the Intelligent Key may not function.
. If the Intelligent Key is placed near the
door or window outside the vehicle, the
Intelligent Key may function.
OPERATING RANGE FOR ENGINE
START FUNCTION
CV37D1-6030EAE0-2A71-404A-8C29-FAFDB2EEFD37
The Intelligent Key can only be used for
starting the engine when the Intelligent
Key is within the specified operating range
1 .
*
When the Intelligent Key battery is almost
discharged or strong radio waves are
present near the operating location, the
Intelligent Key system’s operating range
becomes narrower and may not function
properly.
If the Intelligent Key is within the operating
range, it is possible for anyone, even
5-12 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(197,1)
turned from the LOCK position.
Some indicators and warnings for operation are displayed in the vehicle information display between the speedometer and
tachometer. (See “Vehicle information display” (P.2-21).)
The ignition lock is designed so that the
ignition switch position cannot be switched
to LOCK until the shift lever is moved to the
P (Park) position.
JVS0241X
PUSH-BUTTON IGNITION SWITCH
OPERATION
CV37D1-9B8FACA2-29C9-4240-8C27-D00044FE6E2A
When the ignition switch is pushed without
depressing the brake pedal, the ignition
switch position will change as follows:
. Push center once to change to ACC.
. Push center two times to change to ON.
. Push center three times to change to
OFF. (No position illuminates.)
. Push center four times to return to ACC.
. Open or close any door to return to
LOCK during the OFF position.
If the battery of the vehicle is discharged,
the push-button ignition switch cannot be
When the ignition switch cannot be pushed
toward the LOCK position, proceed as
follows:
1. Move the shift lever into the P (Park)
position.
2. Push the ignition switch to the OFF
position. The ignition switch position
indicator will not illuminate.
3. Open the door. The ignition switch will
change to the LOCK position.
The shift lever can be moved from the P
(Park) position if the ignition switch is in
the ON position and the brake pedal is
depressed.
PUSH-BUTTON IGNITION SWITCH
POSITIONS
CV37D1-2229A0DC-A631-4E4A-A7EC-3313996B03AA
LOCK (Normal
parking position)
CV37D1-E2F507CB-64CA-4F58-89D1-B22BC61E9D0F
The ignition switch can only be locked in
this position.
The ignition switch will be unlocked when it
is pushed to the ACC position while
carrying the Intelligent Key.
ACC (Accessories)
CV37D1-5A3655C9-DAC6-49A0-A52C-85946FA4D08D
This position activates electrical accessories such as the radio, when the engine
is not running.
ON (Normal
operating position)
CV37D1-D069FD06-4A4C-4C0D-9E4B-ADF4B3227F3C
This position turns on the ignition system
and electrical accessories.
OFF
CV37D1-947259CA-5798-448F-A988-0028B6E8B42E
The engine can be turned off in this
position.
The ignition lock is designed so that the
ignition switch cannot be switched to the
LOCK position until the shift lever is moved
to the P (Park) position.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(198,1)
4. Push the ignition switch while depressing the brake pedal within 10 seconds
after the chime sounds. The engine will
start.
CAUTION
Do not leave the vehicle with the pushbutton ignition switch in ACC or ON positions when the engine is not running for an
extended period. This can discharge the
battery.
After step 3 is performed, when the ignition
switch is pushed without depressing the
brake pedal, the ignition switch position
will change to ACC.
EMERGENCY
ENGINE SHUT OFF
CV37D1-B97EFA74-7631-43F4-BB12-722169CB72A8
To shut off the engine in an emergency
situation while driving, perform the following procedure:
. Rapidly push the push-button ignition
switch 3 consecutive times in less than
1.5 seconds, or
. Push and hold the push-button ignition
switch for more than 2 seconds.
JVS0404X
INTELLIGENT KEY BATTERY DISCHARGE CV37D1-881AEDE4-EC8A-459A-A547-0DBF545170CF
If the battery of the Intelligent Key is
discharged, or environmental conditions
interfere with the Intelligent Key operation,
start the engine according to the following
procedure:
1. Move the shift lever to the P (Park)
position.
2. Firmly apply the foot brake.
NOTE:
. When the ignition switch is pushed to
the ACC or ON position or the engine is
started by the above procedures, the
Intelligent Key battery discharge indicator appears in the vehicle information display even if the Intelligent Key
is inside the vehicle. This is not a
malfunction. To turn off the Intelligent
Key battery discharge indicator, touch
the ignition switch with the Intelligent
Key again.
. If the Intelligent Key battery discharge
indicator appears, replace the battery
as soon as possible. (See “Intelligent
Key battery replacement” (P.8-28).)
3. Touch the ignition switch with the
Intelligent Key as illustrated. (A chime
will sound.)
5-14 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(199,1)
BEFORE STARTING THE ENGINE
CV37D1-07A09103-0621-4AD1-9346-3CE162BEDDB5
. Make sure the area around the vehicle
is clear.
. Check fluid levels such as engine oil,
coolant, brake fluid and window washer
fluid as frequently as possible, or at
least whenever you refuel.
. Check that all windows and lights are
clean.
. Visually inspect tires for their appearance and condition. Also check tires for
proper inflation.
. Lock all doors.
. Position seat and adjust head restraints.
. Adjust inside and outside mirrors.
. Fasten seat belts and ask all passengers to do likewise.
. Check the operation of warning lights
when the ignition switch is pushed to
the ON position. (See “Warning lights,
indicator lights and audible reminders”
(P.2-12).)
STARTING THE ENGINE
CV37D1-15E689F6-66C8-4808-987F-20991B32D7B4
1. Apply the parking brake.
2. Move the shift lever to the P (Park) or N
(Neutral) position. (P is recommended.)
The starter is designed not to operate
unless the shift lever is in either of the
above positions.
3. Push the ignition switch to the ON
position. Depress the brake pedal and
push the ignition switch to start the
engine.
To start the engine immediately, push
and release the ignition switch while
depressing the brake pedal with the
ignition switch in any position.
. If the engine is very hard to start in
extremely cold weather or when
restarting, depress the accelerator
pedal a little (approximately 1/3 to
the floor) and while holding, crank
the engine. Release the accelerator
pedal when the engine starts.
. If the engine is very hard to start
because it is flooded, depress the
accelerator pedal all the way to the
floor and hold it. Push the ignition
switch to the ON position to start
cranking the engine. After 5 or 6
seconds, stop cranking by pushing
the ignition switch to OFF. After
cranking the engine, release the
accelerator pedal. Crank the engine
with your foot off the accelerator
pedal by depressing the brake pedal
and pushing the push-button ignition switch to start the engine. If the
engine starts, but fails to run, repeat
the above procedure.
CAUTION
Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, push the ignition switch to OFF and
wait 10 seconds before cranking again,
otherwise the starter could be damaged.
4. Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the
engine while warming it up. Drive at
moderate speed for a short distance
first, especially in cold weather. In cold
weather, keep the engine running for a
minimum of 2 - 3 minutes before
shutting it off. Starting and stopping
the engine over a short period of time
may make the vehicle more difficult to
start.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(200,1)
DRIVING THE VEHICLE
CV37D1-3ADAC877-F0EE-4EEE-B344-6B3344CBF91D
When racing the engine up to 4,500
rpm or more under no load condition,
the engine will enter the fuel cut mode.
1. Make sure that the Intelligent Key is on
you.
5. To stop the engine, shift the shift lever
to the P (Park) position and push the
ignition switch to the OFF position.
3. Push the ignition switch once to the ON
position.
NOTE:
Care should be taken to avoid situations
that can lead to potential battery discharge and potential no-start conditions
such as:
1. Installation or extended use of electronic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.)
2. Depress the brake pedal.
For additional information about the remote engine start function, see “Remote
engine start” (P.3-20).
AUTOMATIC
TRANSMISSION (AT)
CV37D1-658E6FAE-D0C8-4287-8C2F-7C3405FB31DD
The Automatic Transmission (AT) in your
vehicle is electronically controlled by a
transmission control module to produce
maximum efficiency and smooth operation.
Shown on the following pages are the
recommended operating procedures for
this transmission. Follow these procedures
for maximum vehicle performance and
driving enjoyment.
Starting the
vehicle
CV37D1-4DAD59A5-630D-4CAA-B791-6073B0B64774
After starting the engine, fully depress the
foot brake pedal and push the shift lever
button before shifting the shift lever to the
R (Reverse), N (Neutral), D (Drive) or Manual
shift mode position. Be sure the vehicle is
fully stopped before attempting to shift the
shift lever.
2. Vehicle is not driven regularly and/or
only driven short distances.
This Automatic Transmission (AT) model is
designed so that the foot brake pedal must
be depressed before shifting from P (Park)
to any drive position while the ignition
switch is in the ON position.
In these cases, the battery may need to be
charged to maintain battery health.
REMOTE START
(if so equipped)
CV37D1-17311495-16CD-4C76-A14E-78C7BA53F7B9
Vehicles started with the remote engine
start function require the ignition switch to
be placed in the ON position before the
shift lever can be moved from the P (Park)
position. To place the ignition switch in the
ON position, perform the following steps:
The shift lever cannot be moved out of the
P (Park) position and into any of the other
gear positions if the ignition switch is
placed in the LOCK, OFF or ACC position.
5-16 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(201,1)
1. Keep the foot brake pedal depressed
and push the shift lever button to shift
into a driving gear.
2. Release the parking brake and foot
brake, then gradually start the vehicle
in motion.
roads. This may cause a loss of control.
CAUTION
.
To avoid possible damage to your
vehicle; when stopping the vehicle on
an uphill grade, do not hold the vehicle
by depressing the accelerator pedal. The
foot brake should be used for this
purpose.
.
Except in an emergency, do not shift to
the N (Neutral) position while driving.
Coasting with the transmission in the N
(Neutral) position may cause serious
damage to the transmission.
WARNING
.
Do not depress the accelerator pedal
while shifting from P (Park) or N (Neutral)
to R (Reverse), D (Drive) or manual shift
mode. Always depress the brake pedal
until shifting is completed. Failure to do
so could cause you to lose control and
have an accident.
.
Cold engine idle speed is high, so use
caution when shifting into a forward or
reverse gear before the engine has
warmed up.
.
Never shift to either P (Park) or R
(Reverse) position while the vehicle is
moving forward and P (Park) or D (Drive)
position while the vehicle is moving
reversing. This could cause an accident
or damage the transmission.
.
JVS0186X
Shift lever
To move the shift lever,
:
:
:
Push the button while depressing the
brake pedal,
Push the button,
Just move the shift lever.
Shifting
CV37D1-41D731C7-80D2-4187-9850-D9937B0D67A0
After starting the engine, fully depress the
brake pedal and shift the shift lever from P
(Park) to R (Reverse), N (Neutral), D (Drive)
or Manual shift mode position.
Push the button to shift into P (Park) or R
(Reverse). All other positions can be
selected without pushing the button.
Do not downshift abruptly on slippery
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(202,1)
WARNING
Apply the parking brake if the shift lever is
in any position while the engine is not
running. Failure to do so could cause the
vehicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
CAUTION
Make sure the vehicle is completely stopped
and the transmission is in the P (Park)
position.
P (Park) position:
CV37D1-F7112F84-B4DC-42FF-BAAF-071602CB6FBF
Use this position when the vehicle is
parked or when starting the engine. Make
sure the vehicle is completely stopped. The
brake pedal must be depressed and the
shift lever button pushed in to move the
shift lever from the N (Neutral) position or
any drive position to the P (Park) position.
Apply the parking brake. When parking on
a hill, apply the parking brake first, then
move the shift lever to the P (Park)
position.
CAUTION
Use this position only when the vehicle is
completely stopped.
R (Reverse):CV37D1-5BBEB2A5-9023-4550-95C0-53D9342B4C88
Use this position to back up. Always be
sure the vehicle is completely stopped
before selecting the R (Reverse) position.
The brake pedal must be depressed and
the shift lever button pushed in to move
the shift lever from the P (Park) position,
the N (Neutral) position or any drive
position to the R (Reverse) position.
N (Neutral):CV37D1-7C434B32-54B2-46F4-87EC-792C655B2A71
Neither forward nor reverse gear is engaged. The engine can be started in this
position. You may shift to the N (Neutral)
position and restart a stalled engine while
the vehicle is moving.
D (Drive): CV37D1-E97AC6AB-B7A0-48E0-9627-FB767E968728
Use this position for all normal forward
driving.
JVS0903X
Paddle shifters (if so equipped)
Manual shift
mode
CV37D1-BF0A9AA6-6CFA-4D8F-90F4-568EAE9C1B74
When the shift lever is in the manual shift
gate, the transmission is ready for the
manual shift mode. Shift ranges can be
selected manually by moving the shift lever
up or down, or pulling the right-side or leftside paddle shifter (if so equipped).
When shifting up, move the shift lever to
the + (up) side or pull the right-side paddle
A
shifter (+) *
(if so equipped). The
transmission shifts to the higher range.
When shifting down, move the shift lever to
the − (down) side or pull the left-side
B (if so equipped). The
paddle shifter (−) *
5-18 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(203,1)
transmission shifts to the lower range.
down long slopes.
When canceling the manual shift mode,
return the shift lever to the D (Drive)
position. The transmission returns to the
normal driving mode.
4M (4th), 3MCV37D1-248C4169-C665-4573-A2F9-788C7CEBED44
(3rd) and 2M (2nd):
Use these positions for hill climbing or
engine braking on downhill grades.
When you pull the paddle shifter (if so
equipped) while in the D (Drive) position,
the transmission will shift to the upper or
lower range temporarily. The transmission
will automatically return to the D (Drive)
position after a short period of time. If you
want to return to the D (Drive) position
manually, pull and hold the paddle shifter
for about 1.5 seconds.
In the manual shift mode, the shift range is
displayed in the vehicle information display.
Shift ranges up or down one by one as
follows:
1M
? M ? M ? M ? M ? M ? 7M
2
3
4
5
6
/
/
/
/
/
/
7M (7th): CV37D1-8818CEC9-1012-4A12-B8E7-064863D22707
Use this position for all normal forward
driving at highway speeds.
6M (6th) and
5M (5th):
CV37D1-EC16CB55-FA2E-46EC-A526-85DDADC329C2
Use these positions when driving up long
slopes, or for engine braking when driving
1M (1st): CV37D1-D6AC9016-E401-43B2-B128-AA47889CE0F2
Use this position when climbing steep hills
slowly or driving slowly through deep
snow, or for maximum engine braking on
steep downhill grades.
. Remember not to drive at high speeds
for extended periods of time in lower
than 7th gear. This reduces fuel economy.
. Moving the shift lever rapidly to the
same side twice will shift the ranges in
succession.
. In the manual shift mode, the transmission may not shift to the selected gear
or may automatically shift to the other
gear. This helps maintain driving performance and reduces the chance of
vehicle damage or loss of control.
. When the transmission does not shift
to the selected gear, the Automatic
Transmission (AT) position indicator (in
the vehicle information display) will
blink and the buzzer will sound.
. In the manual shift mode, the transmission automatically shifts down to 1st
gear before the vehicle comes to a
stop. When accelerating again, it is
necessary to shift up to the desired
range.
Accelerator downshift — In D (Drive)
position —CV37D1-542E1187-7AE3-48BD-B45E-F631844299CE
For passing or hill climbing, fully depress
the accelerator pedal to the floor. This
shifts the transmission down into the lower
gear, depending on the vehicle speed.
Fail-safe
CV37D1-B4B41F66-217F-4211-9BB6-5500BD56819F
When the fail-safe operation occurs, note
that the transmission will be locked in any
of the forward gears according to the
condition.
If the vehicle is driven under extreme
conditions, such as excessive wheel spinning and subsequent hard braking, the
fail-safe system may be activated. This will
occur even if all electrical circuits are
functioning properly. In this case, push
the ignition switch to the OFF position and
wait for 3 seconds. Then push the ignition
switch back to the ON position. The vehicle
should return to its normal operating
condition. If it does not return to its
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(204,1)
normal operating condition, have the
transmission checked and repaired, if
necessary. It is recommended you visit an
INFINITI retailer for this service.
B
using
4. Push down the shift lock *
mechanical key as illustrated.
C
5. Push the shift lever button *
and
move the shift lever to N (Neutral)
D
position *
while holding down the
shift lock.
If the lever cannot be moved out of P (Park),
have the automatic transmission system
checked as soon as possible. It is recommended you visit an INFINITI retailer for
this service.
JVS0188X
Shift lockCV37D1-4CBF5E46-C9E6-41B4-940F-F90ECD96A65E
release
If the battery charge is low or discharged,
the shift lever may not be moved from the P
(Park) position even with the brake pedal
depressed and the shift lever button
pushed.
To move the shift lever, perform the
following procedure:
1. Push the ignition switch to the OFF or
LOCK position.
2. Apply the parking brake.
A using a
3. Remove the shift lock cover *
suitable tool.
Adaptive Shift
Control (ASC)
CV37D1-2BE0D0DF-855C-4440-8D03-E1AE9EF912E9
The adaptive shift control system automatically operates when the transmission is in
the D (Drive) position and selects an
appropriate gear depending on the road
conditions such as uphill, downhill or
curving roads.
Control on uphill
and curving roads:
CV37D1-9F5734E6-2F6C-4CB3-8BE7-B412E0433748
A low gear is maintained that suits the
degree of the slope or curve to allow
smooth driving with a small number of
shifts.
Control on downhill
roads:
CV37D1-E38D9608-C5AE-47FF-81F3-C77A3D1D4450
The adaptive shift control system shifts to
a low gear that suits the degree of the
slope, and uses the engine braking to
5-20 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(205,1)
reduce the number of times that the brake
must be used.
speed while ASC system is operating
than when ASC is not operating.
Control on CV37D1-707C61D1-8F07-4BBD-BAF7-D61B5A87C9DC
winding roads:
A low gear is maintained on continuous
curves that involve repeated acceleration
and deceleration, so that smooth acceleration is available instantly when the accelerator pedal is depressed.
NAVI Shift
Control (if so equipped)
CV37D1-61CE0BFC-1DDC-416B-BD62-E6B1DD7DB0CD
NOTE:
. Adaptive shift control may not operate
when the transmission oil temperature
is low immediately after the start of
driving or when it is very hot.
. During some driving situations, hard
braking for example, the adaptive shift
control may automatically operate. The
transmission may automatically shift
to a lower gear for engine braking. This
increases engine speed but not vehicle
speed. Vehicle speed is controlled by
the accelerator pedal when the vehicle
is in the Adaptive shift control mode.
. When the adaptive shift control operates, the transmission sometimes
maintains a lower gear for a longer
period of time than when adaptive shift
control is not operating. Engine speed
will be higher for a specific vehicle
NAVI Shift Control automatically adjusts
the Automatic Transmission (AT) gear position in certain situations based on road
information from the navigation system.
When the navigation system detects that
the vehicle is approaching a curved road,
NAVI Shift Control will adjust the gear
position if needed to help the driver run
through the curve smoothly.
Precaution CV37D1-896EADF8-6FA8-411E-9AC1-65D480CFDC72
on NAVI shift control:
. The NAVI Shift Control does not provide
steering input or automated driving on
a curve. It is not a speed limit support
system and will not modify your speed
according to local speed limits.
. The NAVI Shift Control is a convenient
system intended to help the vehicle
move through a curve smoothly. However, the driver must always drive
safely and use the brake pedal if
needed.
. The NAVI Shift Control may be delayed
or not operate properly in the following
situations, because this function uses
the road information provided by the
navigation system.
— When the navigation system cannot
accurately detect the location of the
vehicle.
— When the vehicle is driving on a
roadway that is not recognized by
the navigation system.
— When the actual roadway differs
from the map information on the
navigation system due to road construction, traffic lane obstructions,
etc.
. The NAVI Shift Control may not operate
properly in the following situations:
— If the vehicle’s transmission, engine, and/or navigation system,
and/or GPS is malfunctioning.
— If the vehicle speed is higher than
74 MPH (120 km/h) or lower than 19
MPH (30 km/h) and/or transmission
gear is outside the operating range
of the system.
— When the vehicle is driving on a
freeway.
— When the vehicle is driving on a
gentle curve
— When the vehicle is driving with the
shift lever except in the D (Drive)
position.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-21
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(206,1)
PARKING BRAKE
CV37D1-C6728743-9B18-47D2-8752-6DFF42B12BAC
WARNING
JVS0246X
How to enable/disable the NAVI Shift
Control: CV37D1-C64DDBCB-5D5B-4BD8-A405-F2AFC3AB118E
Perform the following steps to enable or
disable the NAVI shift control.
1 and touch
1. Push the MENU button *
[Settings] on the lower display.
2. Touch [Drive Mode Enhancement].
3. Touch [Navi Shift Control] and select the
ON (enabled) or OFF (disabled).
.
Be sure the parking brake is fully
released before driving. Failure to do so
can cause brake failure and lead to an
accident.
.
Do not release the parking brake from
outside the vehicle.
.
Do not use the gear shift in place of the
parking brake. When parking, be sure
the parking brake is fully engaged.
.
To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assistance of others or pets unattended in
your vehicle. Additionally, the temperature inside a closed vehicle on a warm
day can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
SPA2331
To apply: Fully depress the parking brake
1 .
pedal *
To release:
1. Firmly apply the foot brake
2 .
*
1
2. Depress the parking brake pedal *
and the parking brake will be released.
3. Before driving, be sure the brake
warning light goes out.
5-22 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(207,1)
INFINITI DRIVE MODE SELECTOR
CV37D1-C0EEA0E7-8281-43A9-B50B-279933178972
Six, five or four driving modes can be
selected by using the INFINITI Drive Mode
Selector (PERSONAL, SPORT+ (if so
equipped), SPORT, STANDARD, ECO (if so
equipped) and SNOW).
NOTE:
When the INFINITI Drive Mode Selector
selects a mode, the mode may not switch
immediately. This is not a malfunction.
The current mode is displayed in the
vehicle information display.
JVS0189X
INFINITI Drive Mode Selector
To change the mode, push the INFINITI
Drive Mode Selector up or down. The mode
list will appear on the upper display and
you can select the mode.
PERSONAL Û SPORT+ (if so equipped) Û
SPORT ÛSTANDARD Û ECO (if so
equipped) Û SNOW
NOTE:
The mode list will be turned off in
approximately 5 seconds after the mode
is selected.
STANDARDCV37D1-2A69D9CF-8968-4411-B1B1-678B5A8E1A41
MODE
Allows for optimum driving according to
the driving conditions.
This mode will be selected first each time
the engine is started.
SPORT+ MODE
(if so equipped)
CV37D1-9F38180E-4BEE-4857-83DD-FADE562E17C3
In addition to the characteristics of the
SPORT mode, this mode heightens steering
response and changes the setting of VDC
(Vehicle Dynamic Control) for a more sporty
driving experience.
NOTE:
. VDC operation is reduced when the
INFINITI Drive Mode Selector is used to
select the SPORT+ mode (if so
equipped). The VDC system may not
operate in the same circumstances
when compared to operation in the
standard mode. To help prevent accidents drive carefully, avoid careless or
dangerous driving techniques and be
especially careful when driving and
cornering on slippery surfaces.
. In the SPORT+ mode, fuel economy may
be reduced.
JVS0191M
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-23
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(208,1)
SPORT MODE
CV37D1-12F87C14-3739-48A8-BB8F-4BD7B2C4BCBD
OperationCV37D1-9412D164-939D-4D3B-8652-D9F79E95161C
. Adjusts the engine and transmission
points for a higher response.
. The setting of the steering system is
adjusted to provide a quick steering
response and a heavy steering effort.
. The setting of the suspension system is
adjusted to increase the damping force.
(if so equipped)
Select the ECO mode using the INFINITI
Drive Mode Selector. The ECO drive indicator light on the instrument panel illuminates.
NOTE:
In the SPORT mode, fuel economy may be
reduced.
SNOW MODE
CV37D1-2CF0CF99-743E-4A2F-B896-63241986BC6D
Changes the engine characteristics to aid
driving on slippery roads.
ECO MODECV37D1-83A58480-0586-4801-B32F-A1E3F28863D3
(if so equipped)
Assists the driver’s eco-driving. The engine
and transmission points are adjusted for
improved fuel economy, providing such a
driving features as smooth starting or
constant cruising.
NOTE:
Selecting the ECO mode will not necessarily improve fuel economy as many driving
factors influence its effectiveness.
blinking or remains off, the ECO pedal
system increases the reaction force of the
accelerator pedal.
When the accelerator pedal is depressed
within the range of economy drive, the ECO
drive indicator light illuminates in green.
When the accelerator pedal is depressed
above the range of economy drive, the ECO
drive indicator light turns off. For ECO pedal
system equipped models, see “ECO pedal
system” (P.5-24).
The ECO drive indicator light will not
illuminate in the following cases:
. When the shift lever is in the R (Reverse)
position.
. When the vehicle speed is below 2 MPH
(3.2 km/h) or over 90 MPH (144 km/h).
. When the cruise control (if so equipped)
or the Intelligent Cruise Control (ICC)
system (if so equipped) is operated.
ECO pedalCV37D1-B5B27020-9063-4D1B-930D-616910390508
system (if so equipped)
The ECO pedal system helps assist the
driver to improve fuel economy by increasing the reaction force of the accelerator
pedal. When the ECO drive indicator light is
5-24 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(209,1)
system will not vary the reaction force of
the accelerator pedal.
When the INFINITI Drive Mode Selector is
rotated from the ECO mode to another
m o d e ( S TA N D A R D , S P O R T + ( i f s o
equipped), SPORT, SNOW or PERSONAL)
while the ECO pedal system is operating,
the ECO pedal system continues to operate
until the accelerator pedal is released.
JVS0303X
When the ECO drive indicator illuminates in
green, the accelerator reaction force is
normal. When the ECO drive indicator light
is blinking or remains off, the ECO pedal
system increases the reaction force of the
accelerator pedal.
The ECO pedal system may not vary
accelerator reaction force under the following conditions:
If the accelerator pedal is depressed
quickly, the ECO pedal system will not
increase the reaction force of the acceleration pedal. The ECO pedal system is not
designed to prevent the vehicle from
accelerating.
Adjusting the ECO pedal system reaction
force:
CV37D1-465F7B5E-45A3-47D1-BD61-5BB28191CCCB
The ECO pedal system reaction force can be
adjusted. The reaction force setting will be
maintained until the setting is changed
even if the engine is turned off.
JVS0246X
Setting ECOCV37D1-767EFC07-15ED-4E70-B9F6-033A640C3066
pedal reaction force:
1 and touch
1. Push the MENU button *
[Settings] on the lower display.
2. Touch [Drive Mode Enhancement].
3. Touch [ECO Pedal].
4. To set the reaction force of the ECO
pedal system, touch [Standard] or
[Soft].
5. To turn off the ECO pedal system, touch
[OFF].
. When the shift lever is in the N (Neutral)
or R (Reverse) position.
. When Intelligent Cruise Control (ICC) is
being operated.
If the ECO pedal system malfunctions, it
will cancel automatically. The ECO pedal
When the ECO pedal system is turned off,
the accelerator will operate normally.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-25
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(210,1)
PERSONAL
MODE
CV37D1-AA2B2505-680A-406F-A90C-ABF95CA4D5B1
3. Touch [Back] or [Home] to finish the
PERSONAL mode setting.
When the PERSONAL mode is selected, the
following functions can be adjusted individually.
.
.
.
.
Engine/Transmission:
CV37D1-B3090170-8371-42E2-B576-1897FB749982
“Engine/Transmission” can be set to
[Sport], [Eco] (if so equipped), [Standard]
or [Snow].
Engine/Transmission
Steering
Suspension (if so equipped)
Active Trace Control
Steering (models with Direct Adaptive
Steering): CV37D1-120511B5-2D0E-49FC-B5A6-66F7824E85DB
Seven or four combinations of steering
mode and steering response can be set.
Mode
JVS0246X
How to set
the PERSONAL mode
CV37D1-1FAB1089-86C4-40F5-B556-B47AB8217AD9
Perform the following steps to set the
PERSONAL mode.
1 and touch
1. Push the MENU button *
[Infiniti Drive Mode Selector] on the
lower display.
2. Touch [Engine/Transmission], [Steering], [Suspension] (if so equipped) or
[Active Trace Control] and select each
item. (See “Engine/Transmission”,
“Steering”, “Suspension” and “Active
Trace Control” about the feature of each
item.)
Response
Dynamic+
Sport+ (if so equipped)
Dynamic
Default
Dynamic+
Sport
Dynamic
Default
Standard
Default
Steering (models without Direct Adaptive
Steering): CV37D1-B942CE1F-DF2A-4733-ADA3-491FC356089B
“Steering” can be set to [Sport] or [Standard].
SuspensionCV37D1-869BC715-B5C2-4C3E-A534-A4261163315E
(if so equipped):
“Suspension” can be set to [Sport] or
[Standard].
5-26 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(211,1)
ACTIVE LANE CONTROL (if so equipped)
CV37D1-AEBA00DF-D89A-4E31-8EBA-4D9E6F5F386C
Active TraceCV37D1-89D43330-76B5-4652-B09F-B8215CA4AF77
Control:
“Active Trace Control” can be set to ON
(enabled) or OFF (disabled).
For details about the Active Trace Control,
see “Active trace control” (P.5-138).
Reset Settings:
CV37D1-9CC3CD7F-D2A7-4B55-936B-523408820241
Touch [Reset Settings] and touch [OK] to
restore all the PERSONAL mode settings to
default.
WARNING
Failure to follow the warnings and instructions for proper use of Active Lane Control
could result in serious injury or death.
.
Active Lane Control will not always steer
the vehicle to keep it in the lane. It is not
designed to prevent loss of control. It is
the driver’s responsibility to stay alert,
drive safely, keep the vehicle in the
traveling lane, and be in control of
vehicle at all times.
Active Lane Control enables the driver to
make fewer steering corrections on freeways.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(212,1)
JVS0823X
JVS0822X
1
*
2
*
3
*
Dynamic driver assistance switch
Vehicle information display
Lower display
5-28 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(213,1)
JVS0251X
ACTIVE LANE
CONTROL OPERATION
CV37D1-CC4976DD-A65E-4C3B-A846-FADBCEBDEFAB
Active Lane Control slightly corrects front
tire angles and steering wheel torque to
help reduce the difference between the
vehicle’s direction and the lane direction
2 which is detected by using the camera
*
1 located above the inside mirror.
unit *
menu on the lower display. To turn on
the LDP system, see “Lane Departure
Warning (LDW) system/Lane Departure
Prevention (LDP)” (P.5-35).
. When Active Lane Control is enabled in
the settings menu on the lower display.
Active Lane Control operates under the
following conditions:
. When the vehicle is driven at speeds of
approximately 45 MPH (70 km/h) and
above.
. When the Lane Departure Prevention
(LDP) system is enabled in the settings
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-29
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(214,1)
used for the LDP, Blind Spot Intervention®
(BSI) and Distance Control Assist (DCA)
systems. When the dynamic driver assistance switch is pushed, the LDP, BSI and
DCA systems will also turn on or off
simultaneously. These systems can be
individually set to on or off on the lower
3 .
display *
If Active Lane Control is set to off or the LDP
system is disabled on the lower display,
Active Lane Control will not turn on even if
the dynamic driver assistance switch is
pushed to on.
JVS0822X
TURNING ACTIVE LANE CONTROL
ON/OFF CV37D1-C9F9492C-DDC3-4196-91D5-F7CEB86283EC
Dynamic driver assistance switch
Vehicle information display
Lower display
To turn on Active Lane Control, push the
1
*
2
*
3
*
1 on
dynamic driver assistance switch *
the steering wheel after starting the
engine.
Push the dynamic driver assistance switch
1 again to turn off Active Lane Control.
*
The dynamic driver assistance switch is
5-30 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(215,1)
JVS0246X
JVS0248X
HOW TO ENABLE/DISABLE ACTIVE
LANE CONTROL
CV37D1-DE194FA2-5529-4FE7-B536-A31365E5A355
The status of Active Lane Control can be
checked in the chassis control display in
2 .
the vehicle information display *
Perform the following steps to enable or
disable Active Lane Control.
. When Active Lane Control is turned on,
A is displayed.
the chassis control *
. When Active Lane Control is operational
B
or is operating, the chassis control *
is displayed.
For setting of the chassis control display,
see Infiniti InTouch Owner’s Manual.
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
2. Touch [Lane Assist].
3. Touch [Active Lane Control] to enable or
disable Active Lane Control.
NOTE:
If the Lane Departure Prevention (LDP)
system setting is OFF, Active Lane Control
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-31
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(216,1)
cannot be operated. To use Active Lane
Control, set the LDP system to ON. See
“How to enable/disable the LDP system”
(P.5-39).
.
Active Lane
Control settings
CV37D1-5D2C1649-609C-4F55-9A6B-104397584523
Perform the following steps to set Active
Lane Control.
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
2. Touch [Lane Assist].
3. Enable [Active Lane Control].
4. Touch [Active Lane Control setting] and
select [Low] or [High] to change the
setting of Active Lane Control.
ACTIVE LANE
CONTROL LIMITATIONS
CV37D1-18567D93-57DC-49F8-943B-B3609F61076C
WARNING
Listed below are the limitations for Active
Lane Control. Failure to operate the vehicle
in accordance with these limitations could
result in serious injury or death.
.
Active Lane Control is primarily intended
for use on well-developed freeways or
highways. It may not detect the lane
markers for certain roads, weather or
driving conditions.
— When driving on roads where the
lane width is too narrow.
Using Active Lane Control under some
conditions of road, lane marker or weather, or if you attempt to change lanes
without using the lane change signal
could lead to an unexpected system
operation. In such conditions, you need
to correct the vehicle’s direction with
your steering operation to avoid accidents.
— When driving with a tire that is not
within normal tire conditions (for
example, tire wear, low tire pressure,
installation of spare tire, tire chains,
non-standard wheels).
.
Active Lane Control will not operate at
speeds below approximately 45 MPH (70
km/h) or if it cannot detect lane markers.
.
Active Lane Control may not operate
properly and should not be used under
the following conditions:
— During bad weather (rain, fog, snow,
etc.).
— When driving on slippery roads,
such as on ice or snow, etc.
— When driving on winding or uneven
roads.
— When there is a lane closure due to
road repairs.
— When driving in a makeshift lane.
— When the vehicle is equipped with
non-original steering parts or suspension parts.
.
Active Lane Control may or may not
operate properly under the following
conditions:
— On roads where there are multiple
parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; nonstandard lane markers; or lane markers covered with water, dirt, snow,
etc.
— On roads where discontinued lane
markers are still detectable.
— On roads where there are sharp
curves.
— On roads where there are sharply
contrasting objects, such as shadows, snow, water, wheel ruts,
5-32 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(217,1)
seams or lines remaining after road
repairs. (Active Lane Control could
detect these items as lane markers.)
— When entering or exiting tollgates.
— When driving on roads with a
widening or narrowing lane width.
— On roads where the traveling lane
merges or separates.
— When the vehicle’s traveling direction does not align with the lane
marker.
— When traveling close to the vehicle
in front of you, which obstructs the
lane camera unit detection range.
JVS0824X
— When rain, snow, dirt or object
adheres to the windshield in front
of the lane camera unit.
*
1
Vehicle information display
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-43C8E8CF-B8E1-4C91-BA5B-CBA054808E08
— When the headlights are not bright
due to dirt on the lens or if the aiming
is not adjusted properly.
AutomaticCV37D1-4E07DD9F-CB1E-4107-83D2-7E76282657B5
deactivation
Active Lane Control is not designed to
operate under the following conditions:
— When strong light enters the lane
camera unit. (For example, the light
directly shines on the front of the
vehicle at sunrise or sunset.)
. When the Vehicle Dynamic Control
(VDC) system (except TCS function) or
ABS operates.
. When you operate the lane change
signal and change the traveling lanes
in the direction of the signal. (Active
Lane Control is deactivated for approximately 2 seconds after the lane change
— When a sudden change in brightness occurs. (For example, when the
vehicle enters or exits a tunnel or
under a bridge.)
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-33
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(218,1)
signal is turned off.)
. When the vehicle speed lowers to less
than approximately 45 MPH (70 km/h).
. When the hazard warning flashers are
operated.
After the above conditions have finished
and the operating conditions are satisfied
again, Active Lane Control will resume
operation.
Temporary disabled status at high
temperature
CV37D1-3EE77C53-FD1E-4201-9B32-1A74B98D0A83
If the vehicle is parked in direct sunlight
under high temperature conditions (over
approximately 1048F (408C)) and then
Active Lane Control is turned on, Active
Lane Control may be deactivated automatically. The high cabin temperature message will appear in the vehicle information
1 .
display *
SYSTEM MALFUNCTION
CV37D1-305AE487-F298-40D8-8E37-EAC1321A0909
If Active Lane Control malfunctions, it will
cancel automatically. The chassis control
warning will appear in the vehicle information display.
Action to take:
If the chassis control warning appears, pull
off the road to a safe location and stop the
vehicle. Turn the engine off and restart the
engine. If the chassis control warning
continues to illuminate, it is recommended
you have Active Lane Control checked by an
INFINITI retailer.
JVS0823X
SYSTEM MAINTENANCE
CV37D1-1AE0B264-9E99-4E16-A13F-E0CF9B775F22
1 for Active Lane
The lane camera unit *
Control is located above the inside mirror.
To keep the proper operation of Active Lane
Control and prevent a system malfunction,
be sure to observe the following:
Action to take:
. Always keep the windshield clean.
. Do not attach a sticker (including
transparent material) or install an
accessory near the camera unit.
. Do not place reflective materials, such
as white paper or a mirror, on the
instrument panel. The reflection of
sunlight may adversely affect the cam-
When the interior temperature is reduced,
push the dynamic driver assistance switch
again to turn Active Lane Control back on.
5-34 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(219,1)
LANE DEPARTURE WARNING (LDW)
SYSTEM/LANE DEPARTURE PREVENTION
(LDP) (if so CV37D1-B38D282D-E381-4226-9B23-062B3E7AA6E8
equipped)
era unit’s capability of detecting the
lane markers.
. Do not strike or damage the areas
around the camera unit. It is recommended you contact an INFINITI retailer
if the camera unit is damaged due to an
accident.
WARNING
Failure to follow the warnings and instructions for proper use of the LDW and LDP
systems could result in serious personal
injury or death.
.
The LDW and LDP systems will not
prevent loss of control. It is the driver’s
responsibility to stay alert, drive safely,
keep the vehicle in the traveling lane,
and be in control of the vehicle at all
times.
.
The LDP system may activate if you
change lanes without first activating
your turn signal or, for example, if a
construction zone directs traffic to cross
an existing lane marker. If this occurs,
you may need to apply corrective steering to complete your lane change.
.
Because the LDP system may not activate under the road, weather, and lane
marker conditions described in this
section, it may not activate every time
your vehicle begins to leave its lane and
you will need to apply corrective steering.
. Lane Departure Warning (LDW) system
— warns the driver with an indicator in
the vehicle information display and
vibrations of the steering wheel that
the vehicle is beginning to leave the
driving lane.
. Lane Departure Prevention (LDP) system
— warns the driver with an indicator in
the vehicle information display and
vibrations of the steering wheel, and
helps the driver to return the vehicle
to the center of the traveling lane.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-35
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(220,1)
JVS0823X
1
The LDW and LDP systems use a camera *
installed behind the windshield to monitor
the lane markers of your traveling lane.
JVS0825X
1
*
2
*
3
*
Dynamic driver assistance switch
Driver assist system lane indicator
(green) (on the vehicle information
display)
Lower display
5-36 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(221,1)
LDW SYSTEM
OPERATION
CV37D1-2391B14F-5202-4D89-899F-8F7E17F895CD
LDP SYSTEM
OPERATION
CV37D1-D11B0416-778F-476C-9CAA-E313B05913FE
The LDW system operates above approximately 45 MPH (70 km/h) and when the
lane markings are clear.
The LDP system operates above approximately 45 MPH (70 km/h) and when the
lane markings are clear.
If the vehicle approaches either the left or
the right side of the traveling lane, the
driver assist system lane indicator (orange)
in the vehicle information display will blink
and the steering wheel will vibrate.
If the vehicle approaches either the left or
right side of the traveling lane, the driver
assist system lane indicator (orange) in the
vehicle information display will blink and
the steering wheel will vibrate. Then, the
LDP system will automatically assist the
driver to return the vehicle to the center of
the traveling lane.
NOTE:
The LDW system is not designed to warn
when you operate the lane change signal
and change traveling lanes in the direction
of the signal. (The LDW system will
become operable again approximately 2
seconds after the lane change signal is
turned off.)
JVS0246X
HOW TO ENABLE/DISABLE THE LDW
SYSTEM CV37D1-5D4D0FCE-7292-4390-BC0D-D7430B968B9A
Perform the following steps to enable or
disable the LDW system.
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
2. Touch [Lane Assist].
3. Touch [Lane Departure Warning] to
enable or disable the system.
NOTE:
. The LDP system is not designed to work
when you operate the lane change
signal and change traveling lanes in
the direction of the signal. (The LDP
system will become operable again
approximately 2 seconds after the lane
change signal is turned off.)
. The LDP will not operate or will stop
operating and only a warning chime
will sound under the following conditions.
— When the steering wheel is turned
as far as necessary for the vehicle to
change lanes.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-37
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(222,1)
— When the accelerator pedal is depressed.
— When the Intelligent Cruise Control
(ICC), Distance Control Assist (DCA),
Blind Spot Intervention (BSI), Blind
Spot Warning (BSW), Predictive Forward Collision Warning (PFCW) or
Forward Emergency Braking (FEB)
approach warning occurs.
— When the BSI system activates.
— When the hazard warning flashers
are operated.
— When driving on a curve at a high
speed.
— When the brake pedal is depressed.
(models without Direct Adaptive
Steering)
. While the LDP system is operating, you
may hear a sound of brake operation.
This is normal and indicates that the
LDP system is operating properly.
(models without Direct Adaptive Steering)
JVS0825X
TURNING THE
LDP SYSTEM ON/OFF
CV37D1-4E0855BC-1205-43F0-9417-DF6AA1088232
1
*
2
*
3
*
Dynamic driver assistance switch
Driver assist system lane indicator
(green) (on the vehicle information
display)
Lower display
To turn on the LDP system, push the
1 on
dynamic driver assistance switch *
the steering wheel after starting the
engine. The driver assist system lane
2 in the vehicle informaindicator (green) *
tion display will illuminate.
5-38 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(223,1)
LDW/LDP CV37D1-AA7B1886-AED0-4152-91F5-D6A9157BE770
SYSTEM LIMITATIONS
Push the dynamic driver assistance switch
1 again to turn off the LDP system. The
*
2 will
driver assist system lane indicator *
turn off.
WARNING
1 is
The dynamic driver assistance switch *
used for Active Lane Control (if so
equipped), LDP, Blind Spot Intervention
(BSI) and Distance Control Assist (DCA)
systems. When the dynamic driver assis1 is pushed, Active Lane
tance switch *
Control, BSI and DCA systems will also turn
on or off simultaneously. The LDP system
can be individually set to on or off on the
3 .
lower display *
If the system is set to off, the system will
not turn on even if the dynamic driver
1 is pushed to on. To
assistance switch *
set the system to on or off on the lower
display, see “How to enable/disable the
LDP system” (P.5-39).
Listed below are the system limitations for
the LDW and LDP systems. Failure to operate
the vehicle in accordance with these system
limitations could result in serious injury or
death.
.
The system will not operate at speeds
below 45 MPH (70 km/h) or if it cannot
detect lane markers.
.
The LDP system is primarily intended for
use on well-developed freeways or highways. It may not detect the lane markers
in certain roads, weather or driving
conditions.
.
Do not use the LDP system under the
following conditions as it may not
function properly:
JVS0246X
HOW TO ENABLE/DISABLE THE LDP
SYSTEM CV37D1-FBDC2F4D-6267-44BE-AA3B-4567F2E2FBE3
Perform the following steps to enable or
disable the LDP system.
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
2. Touch [Lane Assist].
3. Touch [Lane Departure Prevention] to
enable or disable the system.
— During bad weather (rain, fog, snow,
etc.).
— When driving on slippery roads,
such as on ice or snow, etc.
— When driving on winding or uneven
roads.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-39
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(224,1)
— When there is a lane closure due to
road repairs.
— On roads where there are sharp
curves.
— When driving in a makeshift or
temporary lane.
— On roads where there are sharply
contrasting objects, such as shadows, snow, water, wheel ruts,
seams or lines remaining after road
repairs. (The LDW and LDP systems
could detect these items as lane
markers.)
— When driving on roads where the
lane width is too narrow.
— When driving without normal tire
conditions (for example, tire wear,
low tire pressure, installation of
spare tire, tire chains, non-standard
wheels).
— When the vehicle is equipped with
non-original steering parts, brake
parts or suspension parts.
.
The camera may not detect lane markers
in the following situations and the LDW
and LDP systems may not operate
properly.
— On roads where there are multiple
parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; nonstandard lane markers; or lane markers covered with water, dirt, snow,
etc.
— On roads where discontinued lane
markers are still detectable.
— When a sudden change in brightness occurs. (For example, when the
vehicle enters or exits a tunnel or
under a bridge.)
— On roads where the traveling lane
merges or separates.
— When the vehicle’s traveling direction does not align with the lane
marker.
— When traveling close to the vehicle
in front of you, which obstructs the
lane camera unit detection range.
— When rain, snow or dirt adheres to
the windshield in front of the lane
camera unit.
— When the headlights are not bright
due to dirt on the lens or if the aiming
is not adjusted properly.
— When strong light enters the lane
camera unit. (For example, the light
directly shines on the front of the
vehicle at sunrise or sunset.)
5-40 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(225,1)
. When the VDC system is turned off.
. When the INFINITI Drive Mode Selector
is turned to the SNOW mode.
Action to take:
When the above conditions no longer exist,
push the dynamic driver assistance switch
2 again to turn the LDP system back on.
*
ConditionCV37D1-F8B1ACA6-289F-4DED-B5C7-0E2C0AECFC16
B
JVS0826X
*
1
2
*
Warnings and indicators (on the vehicle information display)
Dynamic driver assistance switch
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-7B582955-7C17-4F5C-88B9-3D59256EB107
ConditionCV37D1-647B051C-FE23-4279-A27B-4ED0E768B68C
A
Under the following conditions, If the “LDP
currently unavailable” message appears in
the vehicle information display, a chime
will sound and the LDP system will be
turned off automatically.
. When the VDC system (except TCS
function) or ABS operates.
LDW system: If the vehicle is parked in
direct sunlight under high temperature
conditions (over approximately 1048F
(408C)) and then started, the LDW system
may be deactivated automatically. The
“high cabin temperature” warning message will appear in the vehicle information
display.
LDP system: If the vehicle is parked in
direct sunlight under high temperature
conditions (over approximately 1048F
(408C)) and then the LDP system is turned
on, the LDP system may be deactivated
automatically. The “high cabin temperature” message will appear in the vehicle
information display.
Action to take:
When the above conditions no longer exist,
the LDW system will resume automatically.
For the LDP system, push the dynamic
2 again to turn
driver assistance switch *
the LDP system back on.
SYSTEM MALFUNCTION
CV37D1-C6F24BD2-1CDB-4A59-80C8-D911DBEB08BA
LDW system: If the LDW system malfunctions, it will cancel automatically, and the
LDW “malfunction” message will appear in
the vehicle information display.
LDP system: If the LDP system malfunctions, it will cancel automatically. The LDP
“malfunction” message will appear in the
vehicle information display.
Action to take:
Stop the vehicle in a safe location, place
the vehicle in the P (Park) position, turn the
engine off and restart the engine. If the
“malfunction” message continues to appear, have the system checked. It is
recommended you visit an INFINITI retailer
for this service.
The LDW and LDP systems are not available
until the conditions no longer exist.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-41
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(226,1)
BLIND SPOT WARNING (BSW) (if so
equipped)
CV37D1-8148C0B2-58DD-4E5D-87E4-E4AAC4F00A5B
era unit’s capability of detecting the
lane markers.
. Do not strike or damage the areas
around the camera unit. It is recommended you contact an INFINITI retailer
if the camera unit is damaged due to an
accident.
WARNING
Failure to follow the warnings and instructions for proper use of the BSW system
could result in serious injury or death.
.
The BSW system is not a replacement for
proper driving procedure and is not
designed to prevent contact with vehicles or objects. When changing lanes,
always use the side and rear mirrors and
turn and look in the direction your
vehicle will move to ensure it is safe to
change lanes. Never rely solely on the
BSW system.
.
There is a limitation to the detection
capability of the radar. Not every moving
object or vehicle will be detected. Using
the BSW system under some road,
ground, lane marker, traffic or weather
conditions could lead to improper system operation. Always rely on your own
operation to avoid accidents.
JVS0823X
SYSTEM MAINTENANCE
CV37D1-5E444278-7323-4D7D-9B27-06A0B06BB263
1
The lane camera unit *
for LDW/LDP
systems is located above the inside mirror.
To keep the proper operation of LDW/LDP
systems and prevent a system malfunction,
be sure to observe the following:
. Always keep the windshield clean.
. Do not attach a sticker (including
transparent material) or install an
accessory near the camera unit.
. Do not place reflective materials, such
as white paper or a mirror, on the
instrument panel. The reflection of
sunlight may adversely affect the cam-
The BSW system helps alert the driver of
other vehicles in adjacent lanes when
changing lanes.
5-42 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(227,1)
JVS0863X
1
The BSW system uses radar sensors *
installed near the rear bumper to detect
other vehicles in an adjacent lane.
SSD1030
Detection zone
The radar sensors can detect vehicles on
either side of your vehicle within the
detection zone shown as illustrated. This
detection zone starts from the outside
mirror of your vehicle and extends approximately 10 ft (3.0 m) behind the rear
bumper, and approximately 10 ft (3.0 m)
sideways.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-43
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(228,1)
BSW SYSTEM
OPERATION
CV37D1-32E603AE-BDF4-490E-B5AC-9FF1A64159F4
The BSW system operates above approximately 20 MPH (32 km/h).
If the radar sensors detect a vehicle in the
1
detection zone, the side indicator light *
illuminates.
If the turn signal is then activated, the
system chimes (twice) and the side indicator light flashes. The side indicator light
continues to flash until the detected
vehicle leaves the detection zone.
JVS0827X
1
*
2
*
3
*
Side indicator light
Driver assist system blind spot indicator (on the vehicle information display)
Lower display
NOTE:
. The side indicator lights illuminate for a
few seconds when the ignition switch
is placed in the ON position.
. The brightness of the side indicator
lights is adjusted automatically depending on the brightness of the
ambient light.
. If a vehicle comes into the detection
zone after the driver activates the turn
signal, then only the side indicator
light flashes and no chime sounds.
(See “BSW driving situations” (P.546).)
5-44 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(229,1)
can be changed using the following steps:
— Vehicles such as motorcycles, low
height vehicles, or high ground
clearance vehicles.
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
— Oncoming vehicles.
2. Touch [Blind Spot Assist].
— Vehicles remaining in the detection
zone when you accelerate from a
stop.
3. Touch [+] or [-] in [Side Indicator
Brightness] to select [Bright], [Standard] or [Dark].
— A vehicle merging into an adjacent
lane at a speed approximately the
same as your vehicle.
When the brightness setting is changed,
the side indicator lights illuminate for a few
seconds.
JVS0246X
HOW TO ENABLE/DISABLE THE BSW
SYSTEM CV37D1-1D948FE6-E27C-4414-8387-2CBE0E264C7E
Perform the following steps to enable or
disable the BSW system.
— A vehicle which your vehicle overtakes rapidly.
WARNING
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
Listed below are the system limitations for
the BSW system. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
2. Touch [Blind Spot Assist].
.
3. Touch [Blind Spot Warning] to enable or
disable the system.
The BSW system cannot detect all
vehicles under all conditions.
.
The radar sensors may not be able to
detect and activate BSW when certain
objects are present such as:
Setting the side indicator light
brightnessCV37D1-56122B58-1905-4FFD-8173-438CCEC51371
The brightness of the side indicator lights
— A vehicle approaching rapidly from
behind.
BSW SYSTEM
LIMITATIONS
CV37D1-58339DFB-B468-47E7-9AC6-8C7BB87CC49C
— Pedestrians, bicycles, animals.
— A vehicle that passes through the
detection zone quickly.
.
The radar sensor’s detection zone is
designed based on a standard lane
width. When driving in a wider lane, the
radar sensors may not detect vehicles in
an adjacent lane. When driving in a
narrow lane, the radar sensors may
detect vehicles driving two lanes away.
.
The radar sensors are designed to ignore
most stationary objects, however objects such as guardrails, walls, foliage
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-45
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(230,1)
and parked vehicles may occasionally be
detected. This is a normal operation
condition.
.
The following conditions may reduce the
ability of the radar to detect other
vehicles:
— Severe weather
BSW DRIVING
SITUATIONS
CV37D1-506CF134-84A0-482F-AE3F-24012630C90E
Indicator on
Indicator off
Indicator flashing
— Road spray
— Ice/frost/snow build-up on the vehicle
— Dirt build-up on the vehicle
.
.
JVS0737X
Do not attach stickers (including transparent material), install accessories or
apply additional paint near the radar
sensors. These conditions may reduce
the ability of the radar to detect other
vehicles.
Illustration 1 – Approaching from behind
Another vehicle approaching from
behind CV37D1-53E49354-D6D4-4280-8676-8AF6458B18AC
Illustration 1: The side indicator light
illuminates if a vehicle enters the detection
zone from behind in an adjacent lane.
Excessive noise (for example, audio
system volume, open vehicle window)
will interfere with the chime sound, and
it may not be heard.
5-46 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(231,1)
JVS0738X
Illustration 2 – Approaching from behind
Illustration 2: If the driver activates the
turn signal, then the system chimes (twice)
and the side indicator light flashes.
NOTE:
. The radar sensors may not detect
vehicles which are approaching rapidly
from behind.
. If the driver activates the turn signal
before a vehicle enters the detection
zone, the side indicator light will flash
but no chime will sound when the other
vehicle is detected.
JVS0739X
Illustration 3 – Overtaking another vehicle
OvertakingCV37D1-5FC18ED1-F917-4632-9A0E-86F3E8B85D52
another vehicle
Illustration 3: The side indicator light
illuminates if you overtake a vehicle and
that vehicle stays in the detection zone for
approximately 3 seconds.
The radar sensors may not detect slower
moving vehicles if they are passed quickly.
JVS0740X
Illustration 4 – Overtaking another vehicle
Illustration 4: If the driver activates the
turn signal while another vehicle is in the
detection zone, then the system chimes
(twice) and the side indicator light flashes.
NOTE:
. When overtaking several vehicles in a
row, the vehicles after the first vehicle
may not be detected if they are traveling close together.
. The radar sensors may not detect
slower moving vehicles if they are
passed quickly.
. If the driver activates the turn signal
before a vehicle enters the detection
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-47
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(232,1)
zone, the side indicator light will flash
but no chime will sound when the other
vehicle is detected.
JVS0741X
Illustration 5 – Entering from the side
Entering from
the side
CV37D1-40C9A0B9-3960-4155-880D-C60E24A6567A
Illustration 5: The side indicator light
illuminates if a vehicle enters the detection
zone from either side.
JVS0742X
Illustration 6 – Entering from the side
Illustration 6: If the driver activates the
turn signal, then the system chimes (twice)
and the side indicator light flashes.
NOTE:
. The radar sensors may not detect a
vehicle which is traveling at about the
same speed as your vehicle when it
enters the detection zone.
. If the driver activates the turn signal
before a vehicle enters the detection
zone, the side indicator light will flash
but no chime will sound when the other
vehicle is detected.
5-48 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(233,1)
such as ice, frost or dirt obstructing the
radar sensors.
Action to take:
When the above conditions no longer exist,
the system will resume automatically.
If the “side radar obstruction” warning
message continues to appear, have the
system checked. It is recommended you
visit an INFINITI retailer for this service.
SYSTEM MALFUNCTION
CV37D1-9F864D7B-6938-4277-8C51-85F7D8063C8B
JVS0824X
*
1
Vehicle information display
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-A3F1FBC7-3C7C-422F-89E8-E1EA6FB0F745
When radar blockage is detected, the BSW
system will be turned off automatically, a
chime will sound and the “side radar
obstruction” warning message will appear
1 .
in the vehicle information display *
The system is not available until the
conditions no longer exist.
The radar sensors may be blocked by
temporary ambient conditions such as
splashing water, mist or fog. The blocked
condition may also be caused by objects
When the BSW system malfunctions, it will
be turned off automatically, a chime will
sound, and the system “malfunction”
warning message with the driver assist
system blind spot indicator (orange) will
appear in the vehicle information display.
Action to take:
Stop the vehicle in a safe location and
place the shift lever in the P (Park) position.
Turn the engine off and restart the engine.
If the system “malfunction” warning message with the driver assist system blind
spot indicator (orange) continues to be
displayed, have the BSW system checked.
It is recommended you visit an INFINITI
retailer for this service.
JVS0863X
SYSTEM MAINTENANCE
CV37D1-3E2CB2B6-EFF5-4692-A6F0-7D9EB7740A24
1
The two radar sensors *
for the BSW
system are located near the rear bumper.
Always keep the area near the radar
sensors clean.
The radar sensors may be blocked by
temporary ambient conditions such as
splashing water, mist or fog.
The blocked condition may also be caused
by objects such as ice, frost or dirt
obstructing the radar sensors.
Check for and remove objects obstructing
the area around the radar sensors.
Do not attach stickers (including transparStarting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-49
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(234,1)
BLIND SPOT INTERVENTION® (BSI) (if so
equipped)
CV37D1-AE748261-C23D-431B-8CDD-64BD26EA9585
ent material), install accessories or apply
additional paint near the radar sensors.
Do not strike or damage the area around
the radar sensors.
It is recommended you visit an INFINITI
retailer if the area around the radar
sensors is damaged due to a collision.
Radio frequency
statement
CV37D1-C03D7503-8E26-41FE-AE30-6290D632AD94
For USA
This device complies with part 15 of the
FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
Frequency of operation: 24.05GHz —
24.25GHz
WARNING
Failure to follow the warnings and instructions for proper use of the BSI system could
result in serious injury or death.
.
The BSI system is not a replacement for
proper driving procedures and is not
designed to prevent contact with vehicles or objects. When changing lanes,
always use the side and rear mirrors and
turn and look in the direction your
vehicle will move to ensure it is safe to
change lanes. Never rely solely on the
BSI system.
.
There is a limitation to the detection
capability of the radar. Not every moving
object or vehicle will be detected. Using
the BSI system under some road,
ground, lane marker, traffic or weather
conditions could lead to improper system operation. Always rely on your own
operation to avoid accidents.
Field Strength: Not greater than 2.5V/m
peak (0.25V/m average) at a distance of 3
m
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NOTE:
The manufacturer is not responsible for
any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
The BSI system helps alert the driver of
other vehicles in adjacent lanes when
changing lanes, and helps assist the driver
to return the vehicle to the center of the
traveling lane.
For Canada
This device complies with Industry Canada
Standard RSS-310.
5-50 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(235,1)
JVS0864X
1
The BSI system uses radar sensors *
installed near the rear bumper to detect
other vehicles in an adjacent lane. In
addition to the radar sensors, the BSI
2 installed behind
system uses a camera *
the windshield to monitor the lane markers
of your traveling lane.
SSD1030
Detection zone
The radar sensors can detect vehicles on
either side of your vehicle within the
detection zone shown as illustrated.
This detection zone starts from the outside
mirror of your vehicle and extends approximately 10 ft (3.0 m) behind the rear
bumper, and approximately 10 ft (3.0 m)
sideways.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-51
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(236,1)
BSI SYSTEM
OPERATION
CV37D1-96B4C4EA-DE72-44A7-840F-25C8167EECC1
The BSI system operates above approximately 37 MPH (60 km/h).
If the radar sensors detect a vehicle in the
1
detection zone, the side indicator light *
illuminates.
If the turn signal is then activated, the
system chimes (twice) and the side indicator light flashes. The side indicator light
continues to flash until the detected
vehicle leaves the detection zone.
If the BSI system is ON and your vehicle
approaches a lane marker while another
vehicle is in the detection zone, the system
chimes (three times) and the side indicator
light flashes. The BSI system activates to
help return the vehicle back to the center of
the driving lane. The BSI system operates
regardless of turn signal usage.
JVS0828X
1
*
2
*
3
*
4
*
Side indicator light
Driver assist system blind spot indicator (on the vehicle information display)
Dynamic driver assistance switch
Lower display
NOTE:
. BSI warning and system application
will only be activated if the side
indicator light is already illuminated
when your vehicle approaches a lane
marker. If another vehicle comes into
the detection zone after your vehicle
has crossed a lane marker, no BSI
warning or system application will be
5-52 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(237,1)
activated. (For additional information,
see “BSI driving situations” (P.5-56).)
. The BSI system is typically activated
earlier than the Lane Departure Prevention (LDP) system when your vehicle is approaching a lane marker.
JVS0829X
TURNING CV37D1-FBECB068-D5E2-494D-9F26-FEBC5C972CBE
THE BSI SYSTEM ON/OFF
1
*
2
*
3
*
Driver assist system blind spot indicator (green) (on the vehicle information display)
Dynamic driver assistance switch
Lower display
To turn on the BSI system, push the
2 on
dynamic driver assistance switch *
the steering wheel after starting the
engine. The driver assist system blind spot
1 in the vehicle informaindicator (green) *
tion display will illuminate.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-53
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(238,1)
Setting the side indicator light
brightness GUID-305B25D0-2943-49E5-8959-8614894C4B96
Push the dynamic driver assistance switch
2 again to turn off the BSI system. The
*
1
driver assist system blind spot indicator *
will turn off.
The brightness of the side indicator lights
can be changed using the following steps:
2 is
The dynamic driver assistance switch *
used for Active Lane Control (if so
equipped), Blind Spot Intervention (BSI),
Lane Departure Prevention (LDP) and Distance Control Assist (DCA) systems. When
2 is
the dynamic driver assistance switch *
pushed, Active Lane Control, LDP and DCA
systems will also turn on or off simultaneously. The BSI system can be individu3 .
ally set to on or off on the lower display *
If the system is set to off, the system will
not turn on even if the dynamic driver
2 is pushed to on. To
assistance switch *
set the system to on or off on the lower
display, see “How to enable/disable the
BSI system” (P.5-54).
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
2. Touch [Blind Spot Assist].
3. Touch [+] or [-] in [Side Indicator
Brightness] to select [Bright], [Standard] or [Dark].
JVS0246X
HOW TO ENABLE/DISABLE THE BSI
SYSTEM CV37D1-3A7A11FA-9F2B-4938-833A-C12414770692
Perform the following steps to enable or
disable the BSI system.
1 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display.
2. Touch [Blind Spot Assist].
3. Touch [Blind Spot Intervention] to
enable or disable the system.
When the brightness setting is changed,
the side indicator lights illuminate for a few
seconds.
BSI SYSTEM
LIMITATIONS
CV37D1-D3EB355E-5591-4D3B-BF49-C42A29D8401B
WARNING
Listed below are the system limitations for
the BSI system. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
.
The BSI system cannot detect all vehicles under all conditions.
5-54 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(239,1)
.
The radar sensors may not be able to
detect and activate BSI when certain
objects are present such as:
detect vehicles driving two lanes away.
.
— Pedestrians, bicycles, animals.
— Vehicles such as motorcycles, low
height vehicles, or high ground
clearance vehicles.
— Vehicles remaining in the detection
zone when you accelerate from a
stop.
— Oncoming vehicles.
— A vehicle merging into an adjacent
lane at a speed approximately the
same as your vehicle.
— A vehicle approaching rapidly from
behind.
— A vehicle which your vehicle overtakes rapidly.
— A vehicle that passes through the
detection zone quickly.
.
The radar sensor’s detection zone is
designed based on a standard lane
width. When driving in a wider lane, the
radar sensors may not detect vehicles in
an adjacent lane. When driving in a
narrow lane, the radar sensors may
.
— When the vehicle’s traveling direction does not align with the lane
markers.
The radar sensors are designed to ignore
most stationary objects, however objects such as guardrails, walls, foliage
and parked vehicles may occasionally be
detected. This is a normal operation
condition.
— When traveling close to the vehicle
in front of you, which obstructs the
lane camera unit detection range.
— When rain, snow or dirt adheres to
the windshield in front of a lane
camera unit.
The camera may not detect lane markers
in the following situations and the BSI
system may not operate properly.
— When the headlights are not bright
due to dirt on the lens or if aiming is
not adjusted properly.
— On roads where there are multiple
parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; nonstandard lane markers; lane markers
covered with water, dirt, snow, etc.
— When strong light enters a lane
camera unit. (For example: light
directly shines on the front of the
vehicle at sunrise or sunset.)
— On roads where discontinued lane
markers are still detectable.
— When a sudden change in brightness occurs. (For example: when the
vehicle enters or exits a tunnel or
under a bridge.)
— On roads where there are sharp
curves.
— On roads where there are sharply
contrasting objects, such as shadows, snow, water, wheel ruts,
seams or lines remaining after road
repairs.
— On roads where the traveling lane
merges or separates.
.
Do not use the BSI system under the
following conditions because the system
may not function properly.
— During bad weather. (For example:
rain, fog, snow, etc.)
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-55
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(240,1)
— When driving on slippery roads,
such as on ice or snow, etc.
— When driving on winding or uneven
roads.
— When there is a lane closure due to
road repairs.
BSI DRIVING
SITUATIONS
CV37D1-E16450E6-8687-4213-8B48-9FA034783DB0
Indicator on
Indicator off
Indicator flashing
— When driving in a makeshift or
temporary lane.
— When driving on roads where the
lane width is too narrow.
.
— When driving with a tire that is not
within normal tire conditions (for
example, tire wear, low tire pressure,
installation of spare tire, tire chains,
non-standard wheels).
Another vehicle approaching from
behind CV37D1-5C4FC590-E3F0-45DC-BCA5-B2B24BD1593B
— When the vehicle is equipped with
non-original steering parts or suspension parts.
Illustration 1: The side indicator light
illuminates if a vehicle enters the detection
zone from behind in an adjacent lane.
JVS0737X
Illustration 1 – Approaching from behind
Excessive noise (for example, audio
system volume, open vehicle window)
will interfere with the chime sound, and
it may not be heard.
5-56 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(241,1)
but no chime will sound when the other
vehicle is detected.
JVS0738X
Illustration 2 – Approaching from behind
Illustration 2: If the driver activates the
turn signal then the system chimes a
sound (twice) and the side indicator light
flashes.
JVS0760X
Illustration 3 - Approaching from behind
Illustration 3: If the BSI system is on and
your vehicle approaches a lane marker
while another vehicle is in the detection
zone, the system chimes (three times) and
the side indicator light flashes. The BSI
system activates to help return the vehicle
back to the center of the driving lane.
NOTE:
. The radar sensors may not detect
vehicles which are approaching rapidly
from behind.
. If the driver activates the turn signal
before a vehicle enters the detection
zone, the side indicator light will flash
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-57
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(242,1)
JVS0739X
Illustration 4 - Overtaking another vehicle
Overtaking
another vehicle
CV37D1-3A8F82D6-FAB3-4F53-BB4F-EB0FF4562BCA
Illustration 4: The side indicator light
illuminates if you overtake a vehicle and
that vehicle stays in the detection zone for
approximately 3 seconds.
JVS0740X
Illustration 5 - Overtaking another vehicle
Illustration 5: If the driver activates the
turn signal while another vehicle is in the
detection zone, then the system chimes
(twice) and the side indicator light flashes.
JVS0761X
Illustration 6 - Overtaking another vehicle
Illustration 6: If the BSI system is on and
your vehicle approaches a lane marker
while another vehicle is in the detection
zone, the system chimes (three times) and
the side indicator light flashes. The BSI
system activates to help return the vehicle
back to the center of the driving lane.
NOTE:
. When overtaking several vehicles in a
row, the vehicles after the first vehicle
may not be detected if they are traveling close together.
. The radar sensors may not detect
slower moving vehicles if they are
5-58 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(243,1)
passed quickly.
. If the driver activates the turn signal
before a vehicle enters the detection
zone, the side indicator light will flash
but no chime will sound when the other
vehicle is detected.
JVS0741X
Illustration 7 - Entering from the side
Entering from
the side
CV37D1-7B28BCB7-09C8-4BAF-ACB5-1C81F103B774
Illustration 7: The side indicator light
illuminates if a vehicle enters the detection
zone from either side.
NOTE:
The radar sensors may not detect a vehicle
which is traveling at about the same speed
as your vehicle when it enters the detection zone.
JVS0742X
Illustration 8 - Entering from the side
Illustration 8: If the driver activates the
turn signal while another vehicle is in the
detection zone, then the side indicator
light flashes and a chime will sound twice.
NOTE:
If the driver activates the turn signal
before a vehicle enters the detection zone,
the side indicator light will flash but no
chime will sound when another vehicle is
detected.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-59
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(244,1)
JVS0761X
Illustration 9 - Entering from the side
Illustration 9: If the BSI system is on and
your vehicle approaches the lane marker
while another vehicle is in the detection
zone, the system chimes (three times) and
the side indicator light flashes. The BSI
system activates to help return the vehicle
back to the center of the driving lane.
JVS0742X
Illustration 10 - Entering from the side
Illustration 10: The BSI system will not
operate if your vehicle is on a lane marker
when another vehicle enters the detection
zone. In this case only the BSW system
operates.
vehicle is detected.
. BSI will not operate or will stop
operating and only a warning chime
will sound under the following conditions.
— When the brake pedal is depressed.
(models without Direct Adaptive
Steering)
— When the vehicle is accelerated
during BSI system operation
— When steering quickly
— When the ICC, DCA, PFCW or FEB
warnings sound.
— When the hazard warning flashers
are operated.
— When driving on a curve at a high
speed.
NOTE:
. The radar sensors may not detect a
vehicle which is traveling at about the
same speed as your vehicle when it
enters the detection zone.
. If the driver activates the turn signal
before a vehicle enters the detection
zone, the side indicator light will flash
but no chime will sound when the other
5-60 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(245,1)
. When the VDC system is turned off.
. When the INFINITI Drive Mode Selector
is turned to the SNOW mode.
Action to take:
When the above conditions no longer exist,
push the dynamic driver assistance switch
2 again to turn the BSI system back on.
*
JVS0826X
1
*
2
*
Vehicle information display
Dynamic driver assistance switch
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-44FB9B2F-FA84-43E5-8131-D175C39FD782
Under the following conditions, a chime
will sound, the “currently unavailable”
warning message will appear in the vehicle
1 and the BSI system
information display *
will be turned off automatically. The BSI
system will not be available until the
conditions no longer exist.
. When the VDC system (except TCS
function) or ABS operates.
When radar blockage is detected, the BSI
system will be turned off automatically, a
chime will sound and the “side radar
obstruction” warning message will appear
1 .
in the vehicle information display *
The BSI system is not available until the
conditions no longer exist. For additional
information, see “System maintenance”
(P.5-62).
Action to take:
When the above conditions no longer exist,
turn the BSI system on again. If the “side
radar obstruction” warning message appears even after the BSI system is turned
on again, stop the vehicle in a safe
location, place the shift lever in the P
(Park) position and turn the engine off.
Check for and remove objects obscuring
the radar sensors on the rear bumper, and
restart the engine.
If the vehicle is parked in direct sunlight
under high temperature conditions (over
approximately 1048F (408C)) and then the
BSI system is turned on, the BSI system
may be deactivated automatically. The
“high cabin temperature” warning message will appear in the vehicle information
1 .
display *
Action to take:
When the interior temperature is reduced,
push the dynamic driver assistance switch
2 again to turn the BSI system back on.
*
SYSTEM MALFUNCTION
CV37D1-C7FB4764-0BE7-4C90-B8C9-2019CD0D1E1E
When the BSI system malfunctions, it will
be turned off automatically, a chime will
sound, and the system “malfunction”
warning message with the driver assist
system blind spot indicator (orange) will
appear in the vehicle information display.
Action to take:
Stop the vehicle in a safe location and
place the shift lever in the P (Park) position.
Turn the engine off and restart the engine.
If the system “malfunction” warning message with the driver assist system blind
spot indicator (orange) continues to be
displayed, have the BSI system checked. It
is recommended you visit an INFINITI
retailer for this service.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-61
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(246,1)
ent material), install accessories or apply
additional paint near the radar sensors.
Radio frequency
statement
CV37D1-16993A88-48CC-481D-A6B8-4B7F3CCADA9C
Do not strike or damage the area around
the radar sensors.
This device complies with part 15 of the
FCC Rules.
It is recommended you visit an INFINITI
retailer if the area around the radar
sensors is damaged due to a collision.
JVS0864X
SYSTEM MAINTENANCE
CV37D1-D1226349-BD2C-45E4-A69E-A2AB56D76D9A
1
The two radar sensors *
for the BSI
system are located near the rear bumper.
Always keep the area near the radar
sensors clean.
The radar sensors may be blocked by
temporary ambient conditions such as
splashing water, mist or fog.
The blocked condition may also be caused
by objects such as ice, frost or dirt
obstructing the radar sensors.
Check for and remove objects obstructing
the area around the radar sensors.
2 for BSI system is
The lane camera unit *
located above the inside mirror. To keep
the proper operation of BSI and prevent a
system malfunction, be sure to observe the
following:
. Always keep the windshield clean.
. Do not attach a sticker (including
transparent material) or install an
accessory near the camera unit.
. Do not place reflective materials, such
as white paper or a mirror, on the
instrument panel. The reflection of
sunlight may adversely affect the camera unit’s capability of detecting the
lane markers.
. Do not strike or damage the areas
around the camera unit. It is recommended you contact an INFINITI retailer
if the camera unit is damaged due to an
accident.
Do not attach stickers (including transpar-
For USA
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NOTE:
The manufacturer is not responsible for
any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
For Canada
This device complies with Industry Canada
Standard RSS-310.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
Frequency of operation: 24.05GHz —
24.25GHz
5-62 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(247,1)
BACK-UP COLLISION INTERVENTION (BCI)
(if so equipped)
CV37D1-D54B4D45-2B9F-4CD1-A3BC-D6788542EF95
Field Strength: Not greater than 2.5V/m
peak (0.25V/m average) at a distance of 3
m
WARNING
Failure to follow the warnings and instructions for proper use of the BCI system could
result in serious injury or death.
.
.
The BCI system is not a replacement for
proper driving procedure, is not designed to prevent contact with vehicles
or objects and does not provide full
brake power. When backing out of
parking spaces, always use the inside
and rear mirrors and turn and look in the
direction you will move. Never rely solely
on the BCI system.
There is a limitation to the detection
capability of the radar or the sonar.
Using the BCI system under some road,
ground, traffic or weather conditions
could lead to improper system operation. Always rely on your own operation
to avoid accidents.
JVS0866X
1
The BCI system uses radar sensors *
installed on both sides near the rear
bumper to detect an approaching vehicle
2 to detect objects in
and sonar sensors *
the rear.
The BCI system can help alert the driver of
an approaching vehicle or objects behind
the vehicle when the driver is backing out
of a parking space.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-63
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(248,1)
ing vehicle from up to approximately 49 ft
2 detect
(15 m) away. The sonar sensors *
stationary objects behind the vehicle up to
approximately 4.9 ft (1.5 m). Refer to the
illustration for approximate zone coverage
3 .
areas *
JVS0173X
JVS0830X
The radar sensors
1 detect an approach*
5-64 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(249,1)
JVS0173X
BCI SYSTEM
OPERATION
CV37D1-FA73A5F9-354C-4A1F-8CC2-C22EBCBC04B5
When the shift lever is in the R (Reverse)
position and the vehicle speed is less than
approximately 5 MPH (8 km/h), the BCI
system operates.
JVS0831X
1
*
2
*
3
*
4
*
Side indicator light
BCI ON indicator
Upper display
Lower display
If the radar detects a vehicle approaching
from the side or the sonar detects close
stationary objects behind the vehicle, the
system gives visual and audible warnings.
If the driver does not apply the brakes, the
system automatically applies the brake for
a moment when the vehicle is moving
backwards. After the automatic brake
application, the driver must depress the
brake pedal to maintain brake pressure. If
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-65
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(250,1)
the driver’s foot is on the accelerator
pedal, the system pushes the accelerator
upward before applying the brake. If you
continue to accelerate, the system will not
engage the brake.
JVS0304X
Upper display
When the shift lever is placed in the R
(Reverse) position, the indicator on the BCI
1 illuminates on the upper
system key *
display.
JVS0832X
Side indicator light
JVS0307X
Upper display
5-66 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(251,1)
If the radar detects an approaching vehicle
from the side, the system chimes (once),
the side indicator light on the side the
vehicle is approaching from flashes and a
A appears on
yellow rectangular frame *
the upper display.
JVS0172X
Illustration 1
NOTE:
. In the case of several vehicles approaching in a row (Illustration 1) or
in the opposite direction (Illustration
2), a chime may not be sounded by the
BCI system after the first vehicle
passes the sensors.
. The sonar system chime indicating
there is an object behind the vehicle
has a higher priority than the BCI
chime (single beep) indicating an
approaching vehicle. If the sonar system detects an object behind the
vehicle and the BCI system detects an
approaching vehicle at the same time,
the following indications are provided:
— The sonar system chime sounds
— The side indicator light on the side
of the approaching vehicle flashes,
and
— A yellow rectangular frame appears
in the display.
JVS0173X
Illustration 2
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-67
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(252,1)
The BCI system does not operate if the
object is very close to the bumper.
JVS0307X
If an approaching vehicle or object behind
the vehicle is detected when your vehicle is
A will appear on
backing up, a red frame *
the upper display and the system will
chime three times. Then, the brakes will be
applied momentarily. After the automatic
brake application, the driver must depress
the brake pedal to maintain brake pressure.
If the driver’s foot is on the accelerator
pedal, the system moves the accelerator
pedal upward before the braking is applied. However, if you continue to accelerate, the system will not engage the
brakes.
5-68 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(253,1)
JVS0304X
Upper display
TURNING THE
BCI SYSTEM ON/OFF
CV37D1-85D24C56-5257-45FC-8884-1156BDE516B1
The BCI system automatically turns on
every time the engine is started.
JVS0833X
A
*
B
*
Upper display
Lower display
The BCI system can be turned off tempora1 on
rily by touching the BCI system key *
the upper display. The indicator on the BCI
ON key turns off. When the shift lever is
placed in the R (Reverse) position again,
the BCI system is turned on.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-69
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(254,1)
When the BCI system is disabled by
touching [Back-up Collision Intervention],
the BCI system does not turn on automatically by the following operations:
. When the shift lever is placed in the R
(Reverse) position
. When the engine is restarted
JVS0246X
HOW TO ENABLE/DISABLE THE BCI
SYSTEM CV37D1-BD51B193-3D70-44D2-9740-75DB5F7D4363
The BCI system can be turned off permanently using the lower display. Perform the
following steps to enable or disable the BCI
system.
1 and touch
1. Push the MENU button *
[Settings] on the lower display.
2. Touch [Camera/Sonar].
3. Touch [Camera].
4. Touch [Back-up Collision Intervention]
to enable/disable the system.
5-70 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(255,1)
.
The radar sensors detect approaching
(moving) vehicles. The radar sensors
cannot detect every object such as:
— Pedestrians, bicycles, animals or
child operated toy vehicles
— A vehicle that is passing at speeds
greater than approximately 15 MPH
(24 km/h)
.
The radar sensors may not detect approaching vehicles in certain situations:
— Illustration a. When a vehicle parked
next to you obstructs the beam of the
radar sensor.
— Illustration b. When the vehicle is
parked in an angled parking space.
— Illustration c. When the vehicle is
parked on inclined ground.
— Illustration d. When an approaching
vehicle turns into your vehicle’s
parking lot aisle.
JVS0479X
BCI SYSTEM
LIMITATIONS
CV37D1-015F7370-E01C-47EC-B0CE-688B6859DCD2
WARNING
Listed below are the system limitations for
the BCI system. Failure to operate the
— Illustration e. When the angle
formed by your vehicle and approaching vehicle is small.
vehicle in accordance with these system
limitations could result in serious injury or
death.
.
Always check your surroundings and
turn to check what is behind you before
backing up.
.
The following conditions may reduce the
ability of the radar sensors to detect
other vehicles:
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-71
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(256,1)
— Severe weather
— When driving with a tire that is not
within normal tire conditions (for
example, tire wear, low tire pressure,
installation of spare tire, tire chains,
non-standard wheels).
— Road spray
— Ice/frost/dirt build up on the vehicle
.
.
Do not attach stickers (including transparent material), install accessories or
apply additional paint near the radar
sensors. These conditions may reduce
the ability of the radar sensors to detect
other vehicles.
The sonar sensors detect stationary
objects behind the vehicle. The sonar
sensor may not detect:
— When the vehicle is equipped with
non-original brake parts or suspension parts.
.
Excessive noise (for example, audio
system volume, open vehicle window)
will interfere with the chime sound, and
it may not be heard.
JVS0824X
Vehicle information display
— Small or moving objects
*
— Wedge-shaped objects
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-9097D361-3A48-4CE5-8725-42F39CE304C2
1
— Object close to the bumper (less
than approximately 1 ft (30 cm))
If the following message appears in the
1 , a chime
vehicle information display *
will sound and the BCI system will be
turned off automatically.
— Thin objects such as rope, wire and
chain, etc.
.
The brake engagement by the BCI
system is not as effective on a slope as
it is on flat ground. When on a steep
slope the system may not function
properly.
.
Do not use the BCI system under the
following conditions because the system
may not function properly.
. “Unavailable High Accelerator Temp.”:
If the vehicle is parked in direct sunlight under high temperature conditions (over approximately 104 8F (40
8C)) and then started, the BCI system
may be deactivated automatically.
5-72 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(257,1)
ent material), install accessories or apply
additional paint near the radar sensors.
Action to take:
When the interior temperature is reduced, turn off the BCI system and turn
it on again.
. “Unavailable Side Radar Obstruction”:
When side radar blockage is detected.
Action to take:
When the blockage is removed, turn off
the BCI system and turn it on again.
Do not strike or damage the area around
the radar sensors.
It is recommended you visit an INFINITI
retailer if the area around the radar
sensors is damaged due to a collision.
Radio frequency
statement
CV37D1-CB92F1EF-257C-4E49-B4AD-0689AD4B9EF7
For USA
SYSTEM MALFUNCTION
CV37D1-9E7F9DDD-72EE-4D00-ACF3-2C5833AFDB5B
If the BCI system malfunctions, it will turn
off automatically, a chime will sound and
BCI system “malfunction” warning message will appear in the vehicle information
1 .
display *
Action to take:
Stop the vehicle in a safe location and
place the shift lever in the P (Park) position.
Turn the engine off and restart the engine.
If the warning message continues to
appear, have the system checked. It is
recommended you visit an INFINITI retailer
for this service.
This device complies with part 15 of the
FCC Rules.
JVS0863X
SYSTEM MAINTENANCE
CV37D1-AACA1D4C-69A2-4715-A2D4-FD0D6E2D4DC8
1
The two radar sensors *
for the BCI
system is located near the rear bumper.
Always keep the area near the radar
sensors clean.
The radar sensors may be blocked by
temporary ambient conditions such as
splashing water, mist or fog.
The blocked condition may also be caused
by objects such as ice, frost or dirt
obstructing the radar sensors.
Check for and remove objects obstructing
the area around the radar sensors.
Do not attach stickers (including transpar-
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NOTE:
The manufacturer is not responsible for
any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
For Canada
This device complies with Industry Canada
Standard RSS-310.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-73
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(258,1)
CRUISE CONTROL (if so equipped)
CV37D1-23AAF2E8-96D4-4088-8FC4-E0EA618F6140
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
Frequency of operation: 24.05GHz —
24.25GHz
Field Strength: Not greater than 2.5V/m
peak (0.25V/m average) at a distance of 3
m
PRECAUTIONS
ON CRUISE CONTROL
CV37D1-C80C843B-C941-4617-9A6B-8ACA08B59C74
. If the cruise control system malfunctions, it will cancel automatically. The
cruise indicator (green) in the vehicle
information display will then blink to
warn the driver.
. If the engine coolant temperature becomes excessively high, the cruise
control system will be canceled automatically.
. If the cruise indicator (green) blinks,
turn the cruise control MAIN switch off
and have the system checked. It is
recommended you visit an INFINITI
retailer for this service.
. The cruise indicator (green) may sometimes blink when the cruise control
MAIN switch is turned ON while pushing the SET/COAST (-), RESUME/ACCELERATE (+) or CANCEL switch. To properly
set the cruise control system, perform
the steps below in the order indicated.
WARNING
Do not use the cruise control when driving
under the following conditions:
.
when it is not possible to keep the
vehicle at a set speed
.
in heavy traffic or in traffic that varies in
speed
.
on winding or hilly roads
.
on slippery roads (rain, snow, ice, etc.)
.
in very windy areas
Doing so could cause a loss of vehicle
control and result in an accident.
5-74 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(259,1)
SET/COAST (-) switch and release it. (The
cruise indicator (green) will illuminate.)
Take your foot off the accelerator pedal.
Your vehicle will maintain the set speed.
JVS0867X
CRUISE CONTROL
OPERATIONS
CV37D1-FB0B9100-C99C-4A9C-A4E2-8F0F55B5FB3C
1.
2.
3.
4.
RESUME/ACCELERATE (+) switch
SET/COAST (-) switch
CANCEL switch
MAIN (ON·OFF) switch
JVS0306X
Cruise indicator
The cruise indicator and the set vehicle
speed are displayed in the vehicle information display. The cruise indicator indicates
the status of the cruise control system by
the color.
The cruise control allows driving at a speed
between 25 to 90 MPH (40 to 144 km/h)
without keeping your foot on the accelerator pedal.
To turn on the cruise control, push the
MAIN switch on. The cruise indicator
(white) will come on.
To set cruising speed, accelerate your
vehicle to the desired speed, push the
. To pass another vehicle, depress the
accelerator pedal. When you release
the pedal, the vehicle will return to the
previously set speed.
. The vehicle may not maintain the set
speed on winding or hilly roads. If this
happens, drive without the cruise control.
To cancel the preset speed, follow any of
these methods:
1. Push the CANCEL switch.
2. Tap the brake pedal.
3. Turn the MAIN switch off.
After any of the above operations is
performed, the color of the cruise indicator
will change from green to white.
. If you depress the brake pedal while
pushing the RESUME/ACCELERATE (+)
or SET/COAST (-) switch and reset at the
cruising speed, the cruise control will
disengage. Turn the MAIN switch off
once and then turn it on again.
. The cruise control will automatically
cancel if the vehicle slows more than
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-75
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(260,1)
INTELLIGENT CRUISE CONTROL (ICC) (if so
equipped)
CV37D1-E12DEF9F-F1BA-4CEB-86DE-36755D88029A
8 MPH (13 km/h) below the set speed.
. If you move the shift lever to N (Neutral)
position, the cruise control will be
canceled.
To reset at a faster cruising speed, use one
of the following methods:
. Depress the accelerator pedal. When
the vehicle attains the desired speed,
push and release the SET/COAST (-)
switch.
. Push and hold the RESUME/ACCELERATE (+) switch. When the vehicle attains
the speed you desire, release the
switch.
. Push, then quickly release the RESUME/
ACCELERATE (+) switch. Each time you
do this, the set speed will increase by
about 1 MPH (1.6 km/h).
To reset at a slower cruising speed, use
one of the following methods:
. Push, then quickly release the SET/
COAST (-) switch. Each time you do this,
the set speed will decrease by about 1
MPH (1.6 km/h).
To resume the preset speed, push and
release the RESUME/ACCELERATE (+)
switch. The vehicle will resume the last
set cruising speed when the vehicle speed
is over 25 MPH (40 km/h).
. Lightly tap the brake pedal. When the
vehicle attains the desired speed, push
the SET/COAST (-) switch and release it.
. Push and hold the SET/COAST (-)
switch. Release the switch when the
vehicle slows down to the desired
speed.
WARNING
Failure to follow the warnings and instructions for proper use of the ICC system could
result in serious injury or death.
.
ICC is not a collision avoidance or
warning device. For highway use only
and it is not intended for congested
areas or city driving. Failure to apply the
brakes could result in an accident.
.
Always observe posted speed limits and
do not set the speed over them.
.
Always drive carefully and attentively
when using either cruise control mode.
Read and understand the Owner’s Manual thoroughly before using the cruise
control. To avoid serious injury or death,
do not rely on the system to prevent
accidents or to control the vehicle’s
speed in emergency situations. Do not
use cruise control except in appropriate
road and traffic conditions.
.
In the conventional (fixed speed) cruise
control mode, a warning chime will not
sound to warn you if you are too close to
the vehicle ahead. Pay special attention
to the distance between your vehicle and
the vehicle ahead of you or a collision
5-76 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(261,1)
could occur.
The ICC system maintains a selected
distance from the vehicle in front of you
within the speed range of 0 to 90 MPH (0 to
144 km/h) up to the set speed. The set
speed can be selected by the driver
between 20 to 90 MPH (32 to 144 km/h).
The vehicle travels at a set speed when the
road ahead is clear.
The ICC system can be set to one of two
cruise control modes.
. Vehicle-to-vehicle distance control
mode:
For maintaining a selected distance
between your vehicle and the vehicle
in front of you up to the preset speed.
. Conventional (fixed speed) cruise control mode:
For cruising at a preset speed.
JVS0834X
Displays and indicators
ICC switches
MAIN (ON·OFF) switch
A to choose the
Push the MAIN switch *
cruise control mode between the vehicleto-vehicle distance control mode and the
conventional (fixed speed) cruise control
1
*
2
*
A
*
mode.
Once a control mode is activated, it cannot
be changed to the other cruise control
mode. To change the mode, push the MAIN
A once to turn the system off. Then
switch *
A again to turn the
push the MAIN switch *
system back on and select the desired
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-77
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(262,1)
cruise control mode.
Always confirm the setting in the ICC
system display.
For the vehicle-to-vehicle distance control
mode, see “Vehicle-to-vehicle distance
control mode” (P.5-78).
For the conventional (fixed speed) cruise
control mode, see “Conventional (fixed
speed) cruise control mode” (P.5-92).
JVS0835X
HOW TO SELECT THE CRUISE CONTROL MODE
CV37D1-2119FC48-8213-45D0-8F36-CEFFDBA0913C
Selecting the vehicle-to-vehicle
distance control
mode
CV37D1-A118E9F7-859B-4F56-99C3-0CC1D7D06EF6
To choose the vehicle-to-vehicle distance
1 , quickly push and release
control mode *
A .
the MAIN switch *
Selecting the conventional (fixed
speed) cruise
control mode
CV37D1-61BCC5E4-FEDE-4FCB-B6EE-B28A6AC3D206
(fixed speed) cruise control mode” (P.5-92).
VEHICLE-TO-VEHICLE DISTANCE
CONTROLCV37D1-8FBC4AFD-22C3-46CC-855D-F92C37DF0F5C
MODE
In the vehicle-to-vehicle distance control
mode, the ICC system automatically maintains a selected distance from the vehicle
traveling in front of you according to that
vehicle’s speed (up to the set speed), or at
the set speed when the road ahead is clear.
To choose the conventional (fixed speed)
2 , push and hold the
cruise control mode *
A for longer than approxiMAIN switch *
mately 1.5 seconds. See “Conventional
5-78 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(263,1)
JVS0869X
The system is intended to enhance the
operation of the vehicle when following a
vehicle traveling in the same lane and
direction.
A detects a slower
If the radar sensor *
moving vehicle ahead, the system will
reduce the vehicle speed so that your
vehicle follows the vehicle in front at the
selected distance.
The system automatically controls the
throttle and applies the brakes (up to
approximately 40% of vehicle braking
power) if necessary.
The detection range of the sensor is
approximately 650 ft (200 m) ahead.
Vehicle-to-vehicle distance control
mode operation
CV37D1-C712CA46-F1DA-4C8D-AA1F-94E1C58C147F
above the maximum set speed.
The vehicle-to-vehicle distance control
mode is designed to maintain a selected
distance and reduce the speed to match
the slower vehicle ahead; the system will
decelerate the vehicle as necessary and if
the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill. However, the ICC system can only apply up to
approximately 40% of the vehicle’s total
braking power. This system should only be
used when traffic conditions allow vehicle
speeds to remain fairly constant or when
vehicle speeds change gradually. If a
vehicle moves into the traveling lane ahead
or if a vehicle traveling ahead rapidly
decelerates, the distance between vehicles
may become closer because the ICC system
cannot decelerate the vehicle quickly enough. If this occurs, the ICC system will
sound a warning chime and blink the
system display to notify the driver to take
necessary action.
The following items are controlled in the
vehicle-to-vehicle distance control mode:
The system will cancel and a warning
chime will sound if the speed is below
approximately 15 MPH (24 km/h) and a
vehicle is not detected ahead. The system
will also disengage when the vehicle goes
See “Approach warning” (P.5-86).
. When there are no vehicles traveling
ahead, the vehicle-to-vehicle distance
control mode maintains the speed set
by the driver. The set speed range is
between approximately 20 and 90 MPH
(32 and 144 km/h).
. When there is a vehicle traveling ahead,
the vehicle-to-vehicle distance control
mode adjusts the speed to maintain the
distance, selected by driver, from the
vehicle ahead. The adjusting speed
range is up to the set speed. If the
vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within the limitations of the system. The
system will cancel once it judges a
standstill with a warning chime.
. When the vehicle traveling ahead has
moved out from its lane of travel, the
vehicle-to-vehicle distance control
mode accelerates and maintains vehicle speed up to the set speed.
The ICC system does not control vehicle
speed or warn you when you approach
stationary and slow moving vehicles. You
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-79
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(264,1)
Normally when controlling the distance to a
vehicle ahead, this system automatically
accelerates or decelerates your vehicle
according to the speed of the vehicle
ahead. Depress the accelerator to properly
accelerate your vehicle when acceleration
is required for a lane change. Depress the
brake pedal when deceleration is required
to maintain a safe distance to the vehicle
ahead due to its sudden braking or if a
vehicle cuts in. Always stay alert when
using the ICC system.
must pay attention to vehicle operation to
maintain proper distance from vehicles
ahead when approaching toll gates or
traffic congestion.
SSD0254
When driving on the freeway at a set speed
and approaching a slower traveling vehicle
ahead, the ICC system will adjust the
speed to maintain the distance, selected
by the driver, from the vehicle ahead. If the
vehicle ahead changes lanes or exits the
freeway, the ICC system will accelerate and
maintain the speed up to the set speed.
Pay attention to the driving operation to
maintain control of the vehicle as it
accelerates to the set speed.
The vehicle may not maintain the set speed
on winding or hilly roads. If this occurs, you
will have to manually control the vehicle
speed.
5-80 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(265,1)
the set speed.
4. MAIN switch:
Master switch to activate the system
5. DISTANCE switch:
Changes the vehicle’s following distance:
. Long
. Middle
. Short
JVS0836X
JVS0220X
Vehicle-to-vehicle distance control
mode switches
CV37D1-3C61E979-EEE0-480F-8EF4-A69230D7B716
Vehicle-to-vehicle distance control
mode display
and indicators
CV37D1-3D4E4E23-512E-40D3-9C13-5A43F40028C3
The system is operated by a MAIN switch
and four control switches, all mounted on
the steering wheel.
The display is located between the speedometer and tachometer.
1. This indicator indicates the ICC system
status depending on a color.
. Intelligent Cruise Control system ON
indicator (white):
Indicates that the MAIN switch is ON.
. Intelligent Cruise Control system set
indicator (green):
Indicates that cruising speed is set
. Intelligent Cruise Control system
warning (orange):
1. RESUME/ACCELERATE (+) switch:
Resumes set speed or increases speed
incrementally.
2. SET/COAST (-) switch:
Sets desired cruise speed, reduces
speed incrementally.
3. CANCEL switch:
Deactivates the system without erasing
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-81
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(266,1)
Indicates that there is a malfunction
in the ICC system.
2. Vehicle ahead detection indicator:
Indicates whether it detects a vehicle in
front of you.
3. Set vehicle speed indicator:
Indicates the set vehicle speed.
For Canadian models, the speed is
displayed in km/h.
4. Set distance indicator:
Displays the selected distance between
vehicles set with the DISTANCE switch.
JVS0837X
Operating vehicle-to-vehicle distance control
mode
CV37D1-A0DAC4CC-ACB5-4F36-9CA1-9CE958681752
To turn on the cruise control, quickly push
A on. The
and release the MAIN switch *
Intelligent Cruise Control (ICC) system ON
indicator (white), set distance indicator
and set vehicle speed indicator come on
and in a standby state for setting.
JVS0838X
To set cruising speed, accelerate your
vehicle to the desired speed, push the
SET/COAST (-) switch and release it. (The
ICC system set indicator (green), vehicle
ahead detection indicator, set distance
indicator and set vehicle speed indicator
come on.) Take your foot off the accelerator
pedal. Your vehicle will maintain the set
speed.
5-82 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(267,1)
A warning chime will sound and the
“currently unavailable” warning message
appears in the vehicle information display.
JVS0214X
When the SET/COAST (-) switch is pushed
under the following conditions, the system
cannot be set and the ICC indicators will
blink for approximately 2 seconds:
. When traveling below 20 MPH (32
km/h) and the vehicle ahead is not
detected
. When the shift lever is not in the D
(Drive) or manual shift mode
. When the parking brake is applied
. When the brakes are operated by the
driver
When the SET/COAST (-) switch is pushed
under the following conditions, the system
cannot be set.
. When the INFINITI Drive Mode Selector
is turned to the SNOW mode (To use the
ICC system, turn the INFINITI Drive
Mode Selector to a mode other than
the SNOW mode, push the MAIN switch
to turn off the ICC and reset the ICC
switch by pressing the MAIN switch
again.)
For details about the INFINITI Drive
Mode Selector, see “INFINITI Drive
Mode Selector” (P.5-23).
. When the VDC system is off (To use the
ICC system, turn on the VDC system.
Push the MAIN switch to turn off the ICC
system and reset the ICC switch by
pushing the MAIN switch again.)
For details about the VDC system, see
“Vehicle Dynamic Control (VDC) system” (P.5-136).
. When ABS or VDC (including the traction control system) is operating
. When a wheel is slipping (To use the ICC
system, make sure the wheels are no
longer slipping.)
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-83
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(268,1)
Vehicle ahead
not detected:
CV37D1-BB784CAF-C09A-48D2-A3EC-D3B9FA3AED5E
When a vehicle is no longer detected
ahead, the ICC system gradually accelerates your vehicle to resume the previously
set vehicle speed. The ICC system then
maintains the set speed.
When a vehicle is no longer detected the
vehicle ahead detection indicator turns off.
If a vehicle ahead appears during acceleration to the set vehicle speed or any time
the ICC system is in operation, the system
controls the distance to that vehicle.
JVS0210X
*
2
*
1
System set display with vehicle ahead
System set display without vehicle
ahead
The driver sets the desired vehicle speed
based on the road conditions. The ICC
system maintains the set vehicle speed,
similar to standard cruise control, as long
as no vehicle is detected in the lane ahead.
The ICC system displays the set speed.
Vehicle detected
ahead:
CV37D1-C4770B8A-035A-468C-BD75-AC4C9451282C
When a vehicle is detected in the lane
ahead, the ICC system decelerates the
vehicle by controlling the throttle and
applying the brakes to match the speed
of a slower vehicle ahead. The system then
controls the vehicle speed based on the
speed of the vehicle ahead to maintain the
driver selected distance.
When a vehicle is no longer detected under
approximately 15 MPH (24 km/h), the
system will be canceled.
NOTE:
. The stop lights of the vehicle come on
when braking is performed by the ICC
system.
. When the brake operates, a noise may
be heard. This is not a malfunction.
When a vehicle ahead is detected, the
vehicle ahead detection indicator comes
on. The ICC system will also display the set
speed and selected distance.
5-84 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(269,1)
How to change the set vehicle
speed
CV37D1-1933CC86-F314-42E7-887B-171F145279F1
To cancel the preset speed, use any of
these methods:
JVS0211X
When passing another vehicle, the set
speed indicator will flash when the vehicle
speed exceeds the set speed. The vehicle
detect indicator will turn off when the area
ahead of the vehicle is open. When the
pedal is released, the vehicle will return to
the previously set speed.
Even though your vehicle speed is set in
the ICC system, you can depress the
accelerator pedal when it is necessary to
accelerate your vehicle rapidly.
. Push the CANCEL switch. The set vehicle
speed indicator will go out.
. Tap the brake pedal. The set vehicle
speed indicator will go out.
. Turn the MAIN switch off. Both the
Intelligent Cruise Control system set
indicator (green) and set vehicle speed
indicator will go out.
To reset at a faster cruising speed, use one
of the following methods:
. Depress the accelerator pedal. When
the vehicle attains the desired speed,
push and release the SET/COAST (-)
switch.
. Push and hold the RESUME/ACCELERATE (+) switch. The set vehicle speed
will increase by approximately 5 MPH
(5 km/h for Canada).
. Push, then quickly release the RESUME/
ACCELERATE (+) switch. Each time you
do this, the set speed will increase by
approximately 1 MPH (1 km/h for
Canada).
To reset at a slower cruising speed, use
one of the following methods:
. Lightly tap the brake pedal. When the
vehicle attains the desired speed, push
the SET/COAST (-) switch and release it.
. Push and hold the SET/COAST (-)
switch. The set vehicle speed will
decrease by approximately 5 MPH (5
km/h for Canada).
. Push, then quickly release the SET/
COAST (-) switch. Each time you do this,
the set speed will decrease by approximately 1 MPH (1 km/h for Canada).
To resume the preset speed, push and
release the RESUME/ACCELERATE (+)
switch. The vehicle will resume the last
set cruising speed when the vehicle speed
is over 20 MPH (32 km/h).
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-85
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(270,1)
JVS0839X
How to change the set distance to
the vehicle
ahead
CV37D1-478034E0-1738-403B-8E26-9EBF5E8DD002
The distance to the vehicle ahead can be
selected at any time depending on the
traffic conditions.
A
Each time the DISTANCE switch *
is
pushed, the set distance will change to
long, middle, short and back to long again
in that sequence.
JVS0250M
. The distance to the vehicle ahead will
change according to the vehicle speed.
The higher the vehicle speed, the longer the distance.
. If the engine is stopped, the set
distance becomes “long”. (Each time
the engine is started, the initial setting
becomes “long”.)
ApproachCV37D1-75B5DA38-C209-4E02-89D4-2FDDC4ADBC31
warning
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that
vehicle or if another vehicle cuts in, the
system warns the driver with the chime and
5-86 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(271,1)
ICC system display. Decelerate by depressing the brake pedal to maintain a safe
vehicle distance if:
. The chime sounds.
. The vehicle ahead detection indicator
and set distance indicator blink.
The warning chime may not sound in some
cases when there is a short distance
between vehicles. Some examples are:
. When the vehicles are traveling at the
same speed and the distance between
vehicles is not changing
. When the vehicle ahead is traveling
faster and the distance between vehicles is increasing
. When a vehicle cuts in near your vehicle
The warning chime will not sound when:
. Your vehicle approaches other vehicles
that are parked or moving slowly.
. The accelerator pedal is depressed,
overriding the system.
NOTE:
The approach warning chime may sound
and the system display may blink when
the radar sensor detects objects on the
side of the vehicle or on the side of the
road. This may cause the ICC system to
decelerate or accelerate the vehicle. The
radar sensor may detect these objects
when the vehicle is driven on winding
roads, narrow roads, hilly roads or when
entering or exiting a curve. In these cases
you will have to manually control the
proper distance ahead of your vehicle.
Also, the sensor sensitivity can be affected
by vehicle operation (steering maneuver or
driving position in the lane) or traffic or
vehicle condition (for example, if a vehicle
is being driven with some damage).
. When ABS or VDC (including the traction control system) operates
. When distance measurement becomes
impaired due to adhesion of dirt or
obstruction to the sensor
. When a wheel slips
. When the radar signal is temporarily
interrupted
Vehicle-to-vehicle distance control
mode limitations
CV37D1-00697171-AA69-49CD-9867-CE7D2BCF69D4
WARNING
AutomaticCV37D1-D7CD8156-4FA2-46D2-A8EA-E7D5CA7F9CD6
cancellation
A chime sounds under the following conditions and the control is automatically
canceled.
. When the vehicle ahead is not detected
and your vehicle is traveling below the
speed of 15 MPH (24 km/h)
. When the system judges the vehicle is
at standstill
. When the shift lever is not in the D
position or Manual mode
. When the parking brake is applied
. When the INFINITI Drive Mode Selector
is turned to the SNOW mode
. When the VDC system is turned off
Listed below are the system limitations for
the ICC system. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
.
The system is primarily intended for use
on straight, dry, open roads with light
traffic. It is not advisable to use the
system in city traffic or congested areas.
.
This system will not adapt automatically
to road conditions. This system should
be used in evenly flowing traffic. Do not
use the system on roads with sharp
curves, or on icy roads, in heavy rain or
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-87
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(272,1)
circumstances.
in fog.
.
.
.
As there is a performance limit to the
distance control function, never rely
solely on the ICC system. This system
does not correct careless, inattentive or
absent-minded driving, or overcome
poor visibility in rain, fog, or other bad
weather. Decelerate the vehicle speed by
depressing the brake pedal, depending
on the distance to the vehicle ahead and
the surrounding circumstances in order
to maintain a safe distance between
vehicles.
.
Always pay attention to the operation of
the vehicle and be ready to manually
control the proper following distance.
The vehicle-to-vehicle distance control
mode of the ICC system may not be able
to maintain the selected distance between vehicles (following distance) or
selected vehicle speed under some
The system may not detect the vehicle in
front of you in certain road or weather
conditions. To avoid accidents, never use
the ICC system under the following
conditions:
— On roads where the traffic is heavy
or there are sharp curves
— On slippery road surfaces such as
on ice or snow, etc.
— During bad weather (rain, fog, snow,
etc.)
If the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within
the limitations of the system. The
system will cancel once it judges that
the vehicle has come to a standstill and
sound a warning chime. To prevent the
vehicle from moving, the driver must
depress the brake pedal.
— When rain, snow or dirt adhere to
the system sensor
— On steep downhill roads (the vehicle may go beyond the set vehicle
speed and frequent braking may
result in overheating the brakes)
— On repeated uphill and downhill
roads
— When traffic conditions make it
difficult to keep a proper distance
between vehicles because of frequent acceleration or deceleration
.
into the sensor detection zone and cause
automatic braking. You may need to
control the distance from other vehicles
using the accelerator pedal. Always stay
alert and avoid using the ICC system
when it is not recommended in this
section.
In some road or traffic conditions, a
vehicle or object can unexpectedly come
The radar sensor will not detect the
following objects:
Stationary and slow moving vehicles
Pedestrians or objects in the roadway
Oncoming vehicles in the same lane
Motorcycles traveling offset in the travel
lane
The sensor generally detects the signals
returned from the vehicle ahead. Therefore,
if the sensor cannot detect the reflection
from the vehicle ahead, the ICC system
may not maintain the selected distance.
.
.
.
.
The following are some conditions in which
the sensor cannot detect the signals:
. When the snow or road spray from
traveling vehicles reduces the sensor’s
visibility
. When excessively heavy baggage is
loaded in the rear seat or the trunk of
your vehicle
5-88 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(273,1)
The ICC system is designed to automatically check the sensor’s operation within
the limitation of the system. When the
sensor is covered with dirt or is obstructed,
the system will automatically be canceled.
If the sensor is covered with ice, a
transparent or translucent vinyl bag, etc.,
the ICC system may not detect them. In
these instances, the vehicle-to-vehicle distance control mode may not cancel and
may not be able to maintain the selected
following distance from the vehicle ahead.
Be sure to check and clean the sensor
regularly.
SSD0252
The detection zone of the radar sensor is
limited. A vehicle ahead must be in the
detection zone for the vehicle-to-vehicle
distance detection mode to maintain the
selected distance from the vehicle ahead.
and sounding the chime. The driver may
have to manually control the proper distance away from vehicle traveling ahead.
A vehicle ahead may move outside of the
detection zone due to its position within
the same lane of travel. Motorcycles may
not be detected in the same lane ahead if
they are traveling offset from the centerline
of the lane. A vehicle that is entering the
lane ahead may not be detected until the
vehicle has completely moved into the
lane. If this occurs, the ICC system may
warn you by blinking the system indicator
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-89
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(274,1)
JVS0840X
SSD0253
When driving on some roads, such as
winding, hilly, curved, narrow roads, or
roads which are under construction, the
radar sensor may detect vehicles in a
different lane, or may temporarily not
detect a vehicle traveling ahead. This may
cause the ICC system to decelerate or
accelerate the vehicle.
control the proper distance away from the
vehicle traveling ahead.
*
2
*
1
Vehicle information display
MAIN switch
System temporarily
unavailable
CV37D1-DD346E6B-125C-4B76-A270-1C0E094EAC5D
Condition A:CV37D1-822C0622-F81B-426A-8D38-383675EDBE68
Under the following conditions, the ICC
system is automatically canceled. The
chime will sound and the “currently unavailable” warning message will appear in
the vehicle information display.
The detection of vehicles may also be
affected by vehicle operation (steering
maneuver or traveling position in the lane,
etc.) or vehicle condition. If this occurs, the
ICC system may warn you by blinking the
system indicator and sounding the chime
unexpectedly. You will have to manually
. When the VDC is turned off
. When the ABS or VDC (including the
traction control system) operates
. When a tire slips
5-90 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(275,1)
conditions, have the vehicle checked. It is
recommended you visit an INFINITI retailer
for this service.
. When the INFINITI Drive Mode Selector
is turned to the SNOW mode
. When the radar signal is temporarily
interrupted
Action to take:
When the conditions listed above are no
longer present, turn the ICC system back
on to use the system.
Condition B:CV37D1-9D471C73-135F-450B-9A0F-F22B5F8A3601
When the radar sensor area of the front
bumper is covered with dirt or is obstructed, making it impossible to detect a
vehicle ahead, the ICC system is automatically canceled.
JVS0221X
The chime will sound and the “front radar
obstruction” warning message will appear
in the vehicle information display.
Condition C:CV37D1-C833DAAE-4CDA-432F-888A-FFB2B9E8E466
When the ICC system is not operating
properly, the chime sounds and the ICC
system warning (orange) will appear.
Action to take:
Action to take:
If the warning message appears, stop the
vehicle in a safe place, place the shift lever
in the P (Park) position and turn the engine
off. When the radar signal is temporarily
interrupted, clean the sensor area of the
front bumper and restart the engine. If the
“front radar obstruction” warning message
continues to be displayed, it is recommended you have the ICC system checked
by an INFINITI retailer.
If the warning appears, stop the vehicle in
a safe place and place the shift lever in the
P (Park) position. Turn the engine off,
restart the engine, resume driving and set
the ICC system again.
If it is not possible to set the system or the
warning stays on, it may indicate that the
ICC system is malfunctioning. Although
the vehicle is still driveable under normal
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-91
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(276,1)
. Do not attach metallic objects near the
sensor area (brush guard, etc.). This
could cause failure or malfunction.
. Do not alter, remove or paint the front
bumper. It is recommended you contact
an INFINITI retailer before customizing
or restoring the front bumper.
FCC Notice:
For USA:
JVS0869X
System maintenance
CV37D1-E195BDE8-05E3-48C8-880A-3100E46CB318
A is located
The sensor for the ICC system *
behind the grille of the front bumper.
To keep the ICC system operating properly,
be sure to observe the following:
. Always keep the sensor area of the front
grille clean.
. Do not strike or damage the areas
around the sensor.
. Do not cover or attach stickers or similar
objects on the front bumper near the
sensor area. This could cause failure or
malfunction.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
FCC Warning
Changes or modification not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference,
and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
CONVENTIONAL (fixed speed)
CRUISE CONTROL
MODE
CV37D1-A9EC93DD-FFA0-4726-8E89-FEF742A6C8D8
This mode allows driving at a speed
between 25 to 90 MPH (40 to 144 km/h)
without keeping your foot on the accelerator pedal.
WARNING
.
In the conventional (fixed speed) cruise
control mode, a warning chime does not
sound to warn you if you are too close to
the vehicle ahead, as neither the presence of the vehicle ahead nor the
vehicle-to-vehicle distance is detected.
5-92 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(277,1)
.
Pay special attention to the distance
between your vehicle and the vehicle
ahead of you or a collision could occur.
.
Always confirm the setting in the ICC
system display.
.
Do not use the conventional (fixed
speed) cruise control mode when driving
under the following conditions:
— when it is not possible to keep the
vehicle at a set speed
— in heavy traffic or in traffic that
varies in speed
— on winding or hilly roads
— on slippery roads (rain, snow, ice,
etc.)
— in very windy areas
.
Doing so could cause a loss of vehicle
control and result in an accident.
JVS0841X
Conventional (fixed speed) cruise
control switches
CV37D1-7B7DAA66-0A50-4690-83A8-899BAE09F974
1. RESUME/ACCELERATE (+) switch:
Resumes set speed or increases speed
incrementally.
JVS0301X
Conventional (fixed speed) cruise
control mode display and indicators
CV37D1-D7618F09-A63A-4184-A33D-A008354F0F13
The display is located in the vehicle
information display.
1. Cruise indicator:
2. SET/COAST (-) switch:
Sets the desired cruise speed, reduces
speed incrementally.
3. CANCEL switch:
Deactivates the system without erasing
the set speed.
4. MAIN switch:
Master switch to activate the system.
This indicator indicates the condition of
ICC system depending on a color.
. Cruise control ON indicator (white):
Indicates that the MAIN switch is ON.
. Cruise control set indicator (green):
Displays while the vehicle speed is
controlled by the conventional (fixed
speed) cruise control mode of the
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-93
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(278,1)
.
ICC system.
Cruise control system warning (orange):
Indicates that there is a malfunction
in the ICC system.
cruising speed. Pushing the MAIN switch
again will turn the system completely off.
When the ignition switch is placed in the
OFF position, the system is also automatically turned off.
2. Set vehicle speed indicator:
To use the ICC system again, quickly push
and release the MAIN switch (vehicle-tovehicle distance control mode) or push and
hold it (conventional cruise control mode)
again to turn it on.
This indicator indicates the set vehicle
speed.
For Canadian models, the speed is
displayed in km/h.
JVS0842X
Operating conventional (fixed
speed) cruise
control mode
CV37D1-AB41F88C-AA9C-4F75-B164-8999900B5DF5
To turn on the conventional (fixed speed)
cruise control mode, push and hold the
A for longer than about 1.5
MAIN switch *
seconds.
When pushing the MAIN switch on, the
conventional (fixed speed) cruise control
mode display and indicators are displayed
in the vehicle information display. After
you hold the MAIN switch on for longer
than about 1.5 seconds, the ICC system
display turns off. The cruise indicator
appears. You can now set your desired
When the Distance Control Assist (DCA)
system is on, the conventional (fixed
speed) cruise control mode cannot be
turned on even though the MAIN switch is
pushed and held.
To turn on the conventional (fixed speed)
cruise control mode, turn off the DCA
system. See “Distance Control Assist
(DCA)” (P.5-96).
CAUTION
To avoid accidentally engaging cruise control, make sure to turn the MAIN switch off
when not using the ICC system.
5-94 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(279,1)
tain vehicle speed.
To cancel the preset speed, use any of the
following methods:
1. Push the CANCEL switch. The vehicle
speed indicator will turn off.
2. Tap the brake pedal. The vehicle speed
indicator will turn off.
3. Turn the MAIN switch off. Both the
cruise indicator and vehicle speed
indicator will turn off.
JVS0843X
To set cruising speed, accelerate your
vehicle to the desired speed, push the
SET/COAST (-) switch and release it. (The
color of the cruise indicator changes to
green and set vehicle speed indicator
comes on.) Take your foot off the accelerator pedal. Your vehicle will maintain the
set speed.
. To pass another vehicle, depress the
accelerator pedal. When you release
the pedal, the vehicle will return to the
previously set speed.
. The vehicle may not maintain the set
speed when going up or down steep
hills. If this happens, manually main-
To reset at a faster cruising speed, use one
of the following three methods:
1. Depress the accelerator pedal. When
the vehicle attains the desired speed,
push and release the SET/COAST (-)
switch.
2. Push and hold the RESUME/ACCELERATE (+) switch. When the vehicle attains
the desired speed, release the switch.
3. Push, then quickly release the RESUME/ACCELERATE (+) switch. Each
time you do this, the set speed will
increase by about 1 MPH (1.6 km/h).
To reset at a slower cruising speed, use
one of the following three methods:
1. Lightly tap the brake pedal. When the
vehicle attains the desired speed, push
the SET/COAST (-) switch and release it.
2. Push and hold the SET/COAST (-)
switch. Release the switch when the
vehicle slows down to the desired
speed.
3. Push, then quickly release the SET/
COAST (-) switch. Each time you do this,
the set speed will decrease by about 1
MPH (1.6 km/h).
To resume the preset speed, push and
release the RESUME/ACCELERATE (+)
switch. The vehicle will resume the last
set cruising speed when the vehicle speed
is over 25 MPH (40 km/h).
System temporarily
unavailable
CV37D1-6261B5E2-E00B-4FC7-A965-A632DF071762
A chime sounds under the following conditions and the control is automatically
canceled.
. When the vehicle slows down more than
8 MPH (13 km/h) below the set speed
. When the shift lever is not in the D
(Drive) or manual shift mode
. When the parking brake is applied.
. When the VDC operates (including the
traction control system)
. When a wheel slips
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-95
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(280,1)
DISTANCE CONTROL ASSIST (DCA) (if so
equipped)
CV37D1-3CE128E2-BCA6-4BD7-93DE-2E19DE898352
still driveable under normal conditions,
have the vehicle checked. It is recommended you visit an INFINITI retailer for
this service.
WARNING
Failure to follow the warnings and instructions for proper use of the DCA system could
result in serious personal injury or death.
.
Always drive carefully and attentively
when using the DCA system. Read and
understand the Owner’s Manual thoroughly before using the DCA system. To
avoid serious injury or death, do not rely
on the system to prevent accidents or to
control the vehicle’s speed in emergency
situations. Do not use the DCA system
except in appropriate road and traffic
conditions.
.
This system is only an aid to assist the
driver and is not a collision warning or
avoidance device. It is the driver’s
responsibility to stay alert, drive safely
and be in control of the vehicle at all
times.
.
As there is a performance limit to the
distance control function, never rely
solely on the DCA system. This system
does not correct careless, inattentive or
absent-minded driving, or overcome
poor visibility in rain, fog, or other bad
weather. Decelerate the vehicle speed by
JVS0306X
Warning
CV37D1-72526CC3-E5EC-44B6-9285-C81F69E550BE
When the system is not operating properly,
the chime sounds and the color of the
cruise indicator will change to orange.
Action to take:
If the color of the cruise indicator changes
to orange, stop the vehicle in a safe place
and place the shift lever in the P (Park)
position. Turn the engine off, restart the
engine, resume driving and then perform
the setting again.
If it is not possible to set or the indicator
stays on, it may indicate that the system is
malfunctioning. Although the vehicle is
5-96 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(281,1)
depressing the brake pedal, depending
on the distance to the vehicle ahead and
the surrounding circumstances in order
to maintain a safe distance between
vehicles.
.
Always pay attention to the operation of
the vehicle and be ready to manually
decelerate to maintain the proper following distance. The DCA system may not be
able to decelerate the vehicle under
some circumstances.
.
This system only brakes and moves the
accelerator pedal upward to help assist
the driver to maintain a following distance from the vehicle ahead. Acceleration should be operated by the driver.
.
.
ing by the vehicle ahead or when a
vehicle suddenly appears in front of you.
Always stay alert when using the DCA
system.
.
If the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within
the limitations of the system. The
system will cancel with a warning chime
once it judges that the vehicle has come
to a standstill. To prevent the vehicle
from moving, the driver must depress
the brake pedal.
JVS0869X
The DCA system is intended to assist the
driver in keeping a following distance from
the vehicle ahead traveling in the same
lane and direction.
The DCA system does not control vehicle
speed or warn you when you approach
stationary and slow moving vehicles.You
must pay attention to vehicle operation
to maintain proper distance from vehicles ahead.
A detects a slower
If the radar sensor *
moving vehicle ahead, the system will
reduce the vehicle speed to help assist
the driver to maintain a following distance.
The system automatically controls the
throttle and applies the brakes (up to
approximately 40% of vehicle braking
power) if necessary.
The DCA system automatically decelerates your vehicle to help assist the
driver to maintain a following distance
from the vehicle ahead. Manually brake
when deceleration is required to maintain a safe distance upon sudden brak-
The detection range of the sensor is
approximately 650 ft (200 m) ahead.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-97
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(282,1)
DCA SYSTEM
OPERATION
CV37D1-B04160A4-4E97-484F-B700-2A0B402937B4
WARNING
Failure to follow the warnings and instructions for proper use of the DCA system could
result in serious personal injury or death.
JVS0844X
1
*
2
*
3
*
Dynamic driver assistance switch
Driver assist system forward indicator
(green) (on the vehicle information
display)
Vehicle ahead detection indicator (on
the vehicle information display)
4
*
Lower display
.
When the vehicle ahead detection indicator is not illuminated, system will
not control the vehicle or warn the
driver.
.
Never place your foot under the brake
pedal. Your foot may be caught when the
system controls the brake.
.
Depending on the position of the accelerator pedal, the system may not be able
to assist the driver to release the
accelerator pedal appropriately.
The DCA system brakes and moves the
accelerator pedal upward according to the
distance from and the relative speed of the
vehicle ahead to help assist the driver in
maintaining a following distance. The
system will decelerate as necessary and if
the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill. However, the DCA system can only apply up to
5-98 Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(283,1)
approximately 40% of the vehicle’s total
braking power. If a vehicle moves into the
traveling lane ahead or if a vehicle traveling ahead rapidly decelerates, the distance
between vehicles may become closer
because the DCA system cannot decelerate
the vehicle quickly enough. If this occurs,
the DCA system will sound a warning chime
and blink the system display to notify the
driver to take necessary action.
See “Approach warning” (P.5-100).
JVS0244X
1
*
2
*
3
*
System set display with a vehicle
ahead
System set display without a vehicle
ahead
System set display with a vehicle
ahead (brake operation is necessary)
The DCA system helps assist the driver to
keep a following distance to the vehicle
ahead by braking and moving the accelerator pedal upward in the normal driving
condition.
When a vehicle ahead is detected:
The vehicle ahead detection indicator
appears.
When the vehicle approaches a vehicle
ahead:
. If the driver’s foot is not on the
accelerator pedal, the system activates
the brakes to decelerate smoothly as
necessary. If the vehicle ahead comes
to a stop, the vehicle decelerates to a
standstill within the limitations of the
system.
. If the driver’s foot is on the accelerator
pedal, the system moves the acceleraStarting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-99
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(284,1)
tor pedal upward to assist the driver to
release the accelerator pedal.
When brake operation by the driver is
required:
The system alerts the driver by a warning
chime and blinking the vehicle ahead
detection indicator. If the driver’s foot is
on the accelerator pedal after the warning,
the system moves the accelerator pedal
upward to assist the driver to switch to the
brake pedal.
NOTE:
. The stop lights of the vehicle come on
when braking is performed by the DCA
system.
. When the brake operates, a noise may
be heard. This is not a malfunction.
Overriding the system:
The following driver’s operation overrides
the system operation.
. When the driver depresses the accelerator pedal even further while the
system is moving the accelerator pedal
upward, the DCA system control of the
accelerator pedal is canceled.
. When the driver’s foot is on the accelerator pedal, the brake control by the
5-100
Condition:
system is not operated.
. When the driver’s foot is on the brake
pedal, neither the brake control nor the
alert by the system operates.
. When the Intelligent Cruise Control (ICC)
system is set, the DCA system will be
inactive.
faster and the distance between vehicles is increasing
. When a vehicle cuts in near your vehicle
The driver assist system forward indicator
(orange) blinks and the warning chime will
not sound when your vehicle approaches
vehicles that are parked or moving slowly.
Approach CV37D1-FD14D541-F912-40CF-BF9D-2032B0C17A84
warning
NOTE:
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that
vehicle or if another vehicle cuts in, the
system warns the driver with the chime and
DCA system display. Decelerate by depressing the brake pedal to maintain a safe
vehicle distance if:
. The chime sounds.
. The vehicle ahead detection indicator
blinks.
. The driver assist system forward indicator (orange) blinks.
The warning chime may not sound in some
cases when there is a short distance
between vehicles. Some examples are:
. When the vehicles are traveling at the
same speed and the distance between
vehicles is not changing
. When the vehicle ahead is traveling
The approach warning chime may sound
and the driver assist system forward
indicator (orange) may blink when the
radar sensor detects objects on the side of
the vehicle or on the side of the road. This
may cause the DCA system to decelerate or
accelerate the vehicle. The radar sensor
may detect these objects when the vehicle
is driven on winding roads, narrow roads,
hilly roads or when entering or exiting a
curve. In these cases you will have to
manually control the proper distance
ahead of your vehicle.
Also, the sensor sensitivity can be affected
by vehicle operation (steering maneuver or
driving position in the lane) or traffic or
vehicle condition (for example, if a vehicle
is being driven with some damage).
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(285,1)
TURNING THE
DCA SYSTEM ON/OFF
CV37D1-8FA2126D-5265-4330-A914-E149EEE46A10
To turn on the DCA system, push the
1 on
dynamic driver assistance switch *
the steering wheel after starting the
engine. The driver assistance switch in2 in the vehicle information disdicator *
play will appear. Push the dynamic driver
1 again to turn off the
assistance switch *
DCA system. The driver assistance switch
2 will turn off.
indicator *
The system will start to operate after the
vehicle speed is above approximately 3
MPH (5 km/h).
JVS0845X
1
*
2
*
3
*
Dynamic driver assistance switch
Driver assist system forward indicator
(green) (on the vehicle information
display)
Lower display
1 is
The dynamic driver assistance switch *
used for the DCA, Active Lane Control (if so
equipped), LDP and BSI systems. When the
1
dynamic driver assistance switch *
is
pushed, Active Lane Control, LDP and BSI
systems will also turn on or off simultaneously. The DCA system can be individu3 .
ally set to on or off on the lower display *
If the system is set to off, the system will
not turn on even if the dynamic driver
1 is pushed to on. To
assistance switch *
set the system to on or off on the display,
see “How to enable/disable the DCA
system” (P.5-102).
When the conventional (fixed speed) cruise
control mode is operating, the DCA system
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-101
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(286,1)
will not operate. (To use the DCA system,
turn the conventional (fixed speed) cruise
control mode off, then push the dynamic
driver assistance switch.)
For details about the conventional (fixed
speed) cruise control mode, see “Intelligent Cruise Control (ICC)” (P.5-76).
When the engine is turned off, the DCA
system is automatically turned off.
JVS0246X
HOW TO ENABLE/DISABLE THE DCA
SYSTEM CV37D1-2F0D5CE3-C8D3-47B6-8751-D2DE54637324
DCA SYSTEM DISPLAY AND INDICATORS
CV37D1-E190DFD9-BC47-47A2-A56E-F99466E70A9F
Perform the following steps to enable or
disable the DCA system.
The display is located between the speedometer and tachometer.
1 button and touch
1. Push the MENU *
[Driver Assistance] on the lower display.
1. Driver assist system forward indicator
. Driver assist system forward indicator (green):
Indicates that the DCA system is ON.
. Driver assist system forward indicator (orange):
Indicates whether there is a malfunction in the DCA system.
2. Touch [Forward Assist].
3. Touch [Distance Control Assist] to enable or disable the system.
5-102
Condition:
JVS0225X
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(287,1)
2. Vehicle ahead detection indicator:
on the distance to the vehicle ahead and
the surrounding circumstances in order
to maintain a safe distance between
vehicles.
Indicates whether it detects a vehicle in
front of you.
DCA SYSTEM
LIMITATIONS
CV37D1-C199E7D2-61FA-4DA1-8EB1-6030B6EA7E86
.
WARNING
Listed below are the system limitations of
the DCA system. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
The system may not detect the vehicle in
front of you in certain road or weather
conditions. To avoid accidents, never use
the DCA system under the following
conditions:
— On roads with sharp curves
— On slippery road surfaces such as
on ice or snow, etc.
This system will not adapt automatically
to road conditions. Do not use the
system on roads with sharp curves, or
on icy roads, in heavy rain or in fog.
— During bad weather (rain, fog, snow,
etc.)
.
The DCA system will not apply brake
control while the driver’s foot is on the
accelerator pedal.
.
As there is a performance limit to the
distance control function, never rely
solely on the DCA system. This system
does not correct careless, inattentive or
absent-minded driving, or overcome
poor visibility in rain, fog, or other bad
weather. Decelerate the vehicle speed by
depressing the brake pedal, depending
— On steep downhill roads (frequent
braking may result in overheating
the brakes)
.
— When rain, snow or dirt adhere to
the system sensor
using the accelerator pedal. Always stay
alert and avoid using the DCA system
when it is not recommended in this
section.
The radar sensor will not detect the
following objects:
Stationary and slow moving vehicles
Pedestrians or objects in the roadway
Oncoming vehicles in the same lane
Motorcycles traveling offset in the travel
lane
The following are some conditions in which
the sensor cannot detect the signals:
.
.
.
.
. When the snow or road spray from
traveling vehicles reduces the sensor’s
visibility
. When excessively heavy baggage is
loaded in the rear seat or the trunk of
your vehicle
— On repeated uphill and downhill
roads
.
In some road or traffic conditions, a
vehicle or object can unexpectedly come
into the sensor detection zone and cause
automatic braking. You may need to
control the distance from other vehicles
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-103
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(288,1)
SSD0252
The detection zone of the sensor is limited.
A vehicle ahead must be in the detection
zone for the system to operate.
away from vehicle traveling ahead.
A vehicle ahead may move outside of the
detection zone due to its position within
the same lane of travel. Motorcycles may
not be detected in the same lane ahead if
they are traveling offset from the centerline
of the lane. A vehicle that is entering the
lane ahead may not be detected until the
vehicle has completely moved into the
lane. If this occurs, the system may warn
you by blinking the system indicator and
sounding the chime. The driver may have
to manually control the proper distance
5-104
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(289,1)
JVS0826X
SSD0253
When driving on some roads, such as
winding, hilly, curved, narrow roads, or
roads which are under construction, the
sensor may detect vehicles in a different
lane, or may temporarily not detect a
vehicle traveling ahead. This may cause
the system to work inappropriately.
vehicle traveling ahead.
*
2
*
1
Vehicle information display
Dynamic driver assistance switch
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-88553AC5-D42F-4F86-9F98-A2C087491C17
ConditionCV37D1-DBD4B6C0-E98B-4CB2-A34C-B7601F5669EB
A
Under the following conditions, the DCA
system is automatically canceled. The
chime will sound and the “currently unavailable” warning message will appear in
the vehicle information display. The system
will not be able to be set.
The detection of vehicles may also be
affected by vehicle operation (steering
maneuver or traveling position in the lane,
etc.) or vehicle condition. If this occurs, the
system may warn you by blinking the
system indicator and sounding the chime
unexpectedly. You will have to manually
control the proper distance away from the
. When the VDC system is off (To use the
DCA system, turn on the VDC, then
push the dynamic driver assistance
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-105
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(290,1)
2 .) For details about the VDC
switch *
system, see “Vehicle Dynamic Control
(VDC) system” (P.5-136)
. When the VDC or ABS (including the
traction control system) operates
. When the INFINITI Drive Mode Selector
is turned to the SNOW mode (To use the
DCA system, turn the INFINITI Drive
Mode Selector to a mode other than the
SNOW mode, then turn on the dynamic
2 .) For dedriver assistance switch *
tails about the INFINITI Drive Mode
Selector, see “INFINITI Drive Mode
Selector” (P.5-23)
. When the radar signal is temporarily
interrupted
Action to take:
CV37D1-0091A8A4-8714-4724-86EA-A3F9EDE828CA
When the conditions listed above are no
longer present, turn the DCA system back
on to use the system.
Condition CV37D1-7F35B49F-54A2-45C5-BC84-10928BA80E28
B
When the radar sensor area of the front
bumper is covered with dirt or is obstructed, making it impossible to detect a
vehicle ahead, the DCA system is automatically canceled.
The chime will sound, the driver assist
system forward indicator (orange) and the
5-106
Condition:
“front radar obstruction” warning message
will appear in the vehicle information
display.
Action to take:
CV37D1-CFBF9608-D85D-40D6-96A1-0F243E8C2862
If the driver assist system forward indicator
(orange) and the warning message appear,
stop the vehicle in a safe place, place the
shift lever in the P (Park) position and turn
the engine off. When the radar signal is
temporarily interrupted, clean the sensor
area of the front bumper and restart the
engine. If the warning message continues
to be displayed, have the DCA system
checked. It is recommended you visit an
INFINITI retailer for this service.
SYSTEM MALFUNCTION
CV37D1-4EA26598-CF1A-432F-AD96-4D4633819B9C
When the DCA system is not operating
properly, the chime sounds, the driver
assist system forward indicator (orange)
and the system “malfunction” warning
message will appear in the vehicle information display.
Action to take:
If the driver assist system forward indicator
(orange) and the warning message appear,
stop the vehicle in a safe place and place
the shift lever in the P (Park) position. Turn
the engine off, restart the engine, and turn
on the DCA system again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the
system is malfunctioning. Although the
vehicle is still driveable under normal
conditions, have the vehicle checked. It
is recommended you visit an INFINITI
retailer for this service.
SYSTEM MAINTENANCE
CV37D1-623BFC0B-BC28-42A4-B74C-109E1E5A5B56
The sensor for the DCA system is common
with the Intelligent Cruise Control (ICC)
system and is located behind the grille of
the front bumper.
For the sensor maintenance, see “Intelligent Cruise Control (ICC)” (P.5-76).
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(291,1)
FORWARD EMERGENCY BRAKING (FEB)
SYSTEM (if so equipped)
CV37D1-C98533B6-3AEE-40ED-8611-F1306FE0AB0D
FCC Warning
Changes or modification not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference,
and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
WARNING
Failure to follow the warnings and instructions for proper use of the FEB system could
result in serious personal injury or death.
.
The FEB system is a supplemental aid to
the driver. It is not a replacement for the
driver’s attention to traffic conditions or
responsibility to drive safely. It cannot
prevent accidents due to carelessness or
dangerous driving techniques.
.
The FEB system does not function in all
driving, traffic, weather and road conditions.
The FEB system can assist the driver when
there is a risk of a forward collision with
the vehicle ahead in the traveling lane or
with a pedestrian.
JVS0865X
A
The FEB system uses a radar sensor *
located behind the grille of the front
bumper to measure the distance to the
vehicle ahead in the same lane.
For pedestrians, the FEB system uses a
B installed behind the windshield
camera *
in addition to the radar sensor.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-107
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(292,1)
FEB SYSTEM
OPERATION
CV37D1-E048BF5E-C50B-4EE7-AA47-D5EAEE96A216
The FEB system operates at speeds above
approximately 3 MPH (5 km/h). For the
pedestrian detection function, the system
operates at speeds between 6 – 37 MPH
(10 – 60 km/h).
If a risk of a forward collision is detected,
the FEB system will provide the first
warning to the driver by flashing the driver
A
assist system forward indicator (orange) *
and the vehicle ahead detection indicator
B , and providing an audible
(orange) *
warning. In addition, the FEB system
pushes the accelerator pedal up, and then
the system applies partial braking. If the
driver applies the brakes quickly and
forcefully, but the FEB system detects that
there is still the possibility of a forward
collision, the system will automatically
increase the braking force.
JVS0846X
1
*
2
*
FEB system warning light (on the
instrument panel)
Indicators and warnings (on the vehicle information display)
A
Driver assist system forward
*
indicator
5-108
Condition:
B Vehicle ahead detection indicator
*
C FEB system warning indicator
*
3
*
Lower display
If the risk of a collision becomes imminent
and the driver does not take action, the FEB
system issues the second warning to the
driver by flashing the FEB system emerC , providgency warning indicator (red) *
ing an audible warning, and then
automatically applies harder braking.
If a risk of a forward impact with a
pedestrian is detected, the FEB system will
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(293,1)
provide a warning to the driver by flashing
the FEB system emergency warning indiC , provides an audible alert
cator (red) *
and the system will apply partial braking. If
the driver applies the brakes quickly and
forcefully but the FEB system detects that
there is still the possibility of a forward
impact with a pedestrian, the system will
automatically increase the braking force. If
the risk of collision becomes imminent and
the driver does not take action, the FEB
system automatically applies harder braking.
The automatic braking will cease under the
following conditions:
. When the steering wheel is turned to
avoid a collision.
. When the accelerator pedal is depressed.
. When there is no longer a vehicle or a
pedestrian detected ahead.
If the FEB system has stopped the vehicle,
the vehicle will remain at a standstill for
approximately 2 seconds before the brakes
are released.
NOTE:
The vehicle’s stop lights come on when
any braking is performed by the FEB
system.
Depending on vehicle speed and distance
to the vehicle or pedestrian ahead, as well
as driving and roadway conditions, the
system may help the driver avoid a forward
collision or may help mitigate the consequences of a collision should one be
unavoidable. If the driver is handling the
steering wheel, accelerating or braking,
the FEB system will function later or will not
function.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-109
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(294,1)
TURNING CV37D1-1196D6D5-BB9C-49E2-9A40-2BA55A8EF2B2
THE FEB SYSTEM ON/OFF
Perform the following steps to turn the FEB
system on or off.
3 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display
2 .
*
2. Touch [Emergency Assist].
3. Touch [Forward emergency braking] to
turn the system ON/OFF.
When the FEB system is turned off, the FEB
1 illumisystem warning light (orange) *
nates.
JVS0847X
1
*
2
*
3
*
FEB system warning light (on the
instrument panel)
Lower display
MENU button
5-110
Condition:
NOTE:
. The FEB system will be automatically
turned ON when the engine is restarted.
. The Predictive Forward Collision Warning (PFCW) system is integrated into
the FEB system. There is not a separate
selection in the display for the PFCW
system. When the FEB system is turned
off, the PFCW system is also turned off.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(295,1)
FEB SYSTEM
LIMITATIONS
CV37D1-817E251B-D5D4-45FF-A343-2FAEA5BFE495
— If a stationary vehicle is in the
vehicle’s path, the FEB system will
not function when the vehicle is
driven at speeds over approximately
50 MPH (80 km/h).
WARNING
Listed below are the system limitations for
the FEB system. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
.
The FEB system cannot detect all vehicles or pedestrian under all conditions.
.
The radar sensor FEB system does not
detect the following objects:
— Small pedestrians (including small
children), animals and cyclists.
— Pedestrians in wheelchairs or using
mobile transport such as scooters,
child-operated toys, or skateboards.
— Pedestrians who are seated or
otherwise not in a full upright standing or walking position.
— For pedestrian detection, the FEB
system will not function when the
vehicle is driven at speeds over
approximately 37 MPH (60 km/h) or
b e l o w a p p ro x i m a te l y 6 M P H
(10km/h).
The FEB system has some performance
limitations.
— Driving on a bumpy road surface,
such as an uneven dirt road.
— If dirt, ice, snow or other material is
covering the radar sensor area.
— Interference by other radar sources.
.
For pedestrians, the FEB system will not
issue the first warning and will not push
the accelerator pedal up.
.
The FEB system may not function if the
vehicle ahead is narrow (for example a
motorcycle).
— Strong light (for example, sunlight
or high beams from oncoming vehicles) enters the front camera. Strong
light causes the area around the
pedestrian to be cast in a shadow,
making it difficult to see.
.
The FEB system may not function if
speed difference between the two vehicles is too small.
.
The radar sensor FEB system may not
function properly or detect a vehicle
ahead in the following conditions:
— Crossing vehicles
.
— Driving on a steep downhill slope or
roads with sharp curves.
The FEB system will not function for
pedestrians in darkness or in tunnels,
even if there is street lighting in the
area.
.
— Oncoming vehicles
— Obstacles on the roadside
— Poor visibility (conditions such as
rain, snow, fog, dust storms, sandstorms, and road spray from other
vehicles)
— The camera area of windshield is
fogged up, or covered with dirt, water
drops, ice, snow, etc.
— A sudden change in brightness
occurs. (For example, when the vehicle enters or exits a tunnel or a
shaded area or lightning flashes.)
— The poor contrast of a person to the
background, such as having clothing
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-111
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(296,1)
necessary, depress the accelerator pedal
to override the system.
color or pattern which is similar to
the background.
— The pedestrian’s profile is partially
obscured or unidentifiable due to the
pedestrian transporting luggage,
wearing bulky or very loose-fitting
clothing or accessories.
.
.
Excessive noise will interfere with the
warning chime sound, and the chime
may not be heard.
The system performance may degrade in
the following conditions:
— The vehicle is driven on a slippery
road.
— The vehicle is driven on a slope.
— Excessively heavy baggage is
loaded in the rear seat or the trunk
of your vehicle.
.
The system is designed to automatically
check the sensor (radar and camera)’s
functionality, within certain limitations.
The system may not detect blockage of
sensor areas covered by ice, snow or
stickers, for example. In these cases, the
system may not be able to warn the
driver properly. Be sure that you check,
clean and clear sensor areas regularly.
.
In some road and traffic conditions, the
FEB system may unexpectedly apply
partial braking. When acceleration is
5-112
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(297,1)
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-82F2C5EE-F65B-4511-BBD6-9FC023FCA777
ConditionCV37D1-ADF65876-1D32-4AB9-A79E-51DBBAD626F9
A
In the following conditions, the FEB system
1 and the driver
warning light (orange) *
2
assist system forward indicator (orange) *
blinks and the system will be turned off
automatically.
. The radar sensor picks up interference
from another radar source.
. The camera area of windshield is misted
or frozen.
. Strong light is shining from the front.
. The cabin temperature is over approximately 1048F (408C) in direct sunlight.
. The camera area of windshield glass is
continuously covered with dirt, etc.
Action to take:
JVS0848X
1
*
2
*
FEB system warning light (on the
instrument panel)
Driver assist system forward indicator
(on the vehicle information display)
When the above conditions no longer exist,
the FEB system will resume automatically.
NOTE:
When the inside of the windshield on
camera area is misted or frozen, it will take
a period of time to remove it after air
conditioner turns on. If dirt appears on this
area, it is recommended you visit an
INFINITI retailer.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-113
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(298,1)
ConditionCV37D1-B90B1B67-E5E6-4EDD-9754-C7631FFC34C9
B
In the following condition, the FEB system
1 and the driver
warning light (orange) *
2
assist system forward indicator (orange) *
will illuminate and the “front radar obstruction” warning message will appear in
the vehicle information display.
. The sensor area of the front grille is
covered with dirt or is obstructed
Action to take:
1
If the FEB system warning light (orange) *
comes on, stop the vehicle in a safe place,
place the shift lever in the P (Park) position
and turn the engine off. Clean the radar
cover on the front grille with a soft cloth,
and restart the engine. If the warning light
continues to illuminate, have the FEB
system checked. It is recommended you
visit an INFINITI retailer for this service.
NOTE:
If the FEB system stops working, the PFCW
system will also stop working.
ConditionCV37D1-28D97A32-D71E-47EC-B41D-40F527634B38
C
When the accelerator pedal actuator detects that the internal motor temperature is
high, the FEB system is automatically
turned off. The FEB system warning light
5-114
Condition:
1 and the driver assist system
(orange) *
2 will illumiforward indicator (orange) *
nate and the “Unavailable High Accelerator
Temperature” warning message will appear in the vehicle information display.
NOTE:
If the FEB system stops working, the PFCW
system will also stop working.
Action to take:
When the above conditions no longer exist,
the FEB system will resume automatically.
SYSTEM MALFUNCTION
CV37D1-FDCEC082-CF22-4E97-BD60-543BC7C2C3A9
If the FEB system malfunctions, it will be
turned off automatically, a chime will
sound, the FEB system warning light
1 and the driver assist system
(orange) *
2 will illumiforward indicator (orange) *
nate and the system “malfunction” warning message will appear in the vehicle
information display.
Action to take:
1
If the FEB system warning light (orange) *
comes on, stop the vehicle in a safe
location and place the shift lever in the P
(Park) position. Turn the engine off and
restart the engine. If the warning light
continues to illuminate, have the FEB
system checked. It is recommended you
visit an INFINITI retailer for this service.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(299,1)
JVS0865X
SYSTEM MAINTENANCE
CV37D1-793AE201-9674-43D3-B0EE-AA2D274A2697
could block sensor signals, and/or
cause failure or malfunction.
. Do not attach metallic objects near the
radar sensor area (brush guard, etc.).
This could cause failure or malfunction.
. Do not place reflective materials, such
as white paper or a mirror, on the
instrument panel. The reflection of
sunlight may adversely affect the camera unit’s detection capability.
. Do not alter, remove or paint the front
bumper. Before customizing or restoring the front grille, contact an INFINITI
retailer.
FCC Notice:
A is located behind the
The radar sensor *
B is
grille of the front bumper. The camera *
located on the upper side of the windshield.
For USA:
To keep the FEB system operating properly,
be sure to observe the following:
1. This device may not cause harmful
interference, and
. Always keep the sensor area of the front
grille and windshield clean.
. Do not strike or damage the areas
around the sensors (ex. grille, windshield).
. Do not cover or attach stickers, or install
any accessory near the sensors. This
2. This device must accept any interference received, including interference
that may cause undesired operation.
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference,
and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
FCC Warning
Changes or modification not expressly
approved by the party responsible for
compliance could void the user’s authority
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-115
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(300,1)
PREDICTIVE FORWARD COLLISION
WARNING (PFCW) (if so equipped)
CV37D1-2D06B2D7-D7F0-4CC6-8168-05E31E2ED348
WARNING
Failure to follow the warnings and instructions for proper use of the PFCW system
could result in serious injury or death.
.
The PFCW system helps warn the driver
before a collision but will not avoid a
collision. It is the driver’s responsibility
to stay alert, drive safely and be in
control of the vehicle at all times.
The PFCW system can help alert the driver
when there is a sudden braking of a second
vehicle traveling in front of the vehicle
ahead in the same lane.
5-116
Condition:
JVS0869X
A
The PFCW system uses a radar sensor *
located behind the grille of the front
bumper to measure the distance to a
second vehicle ahead in the same lane.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(301,1)
JVS0849X
1
*
2
*
3
*
Driver assist system forward indicator
(on the vehicle information display)
Vehicle ahead detection indicator (on
the vehicle information display)
FEB system warning light (on the
instrument panel)
4
*
Lower display
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-117
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(302,1)
JVS0294X
PFCW SYSTEM
OPERATION
CV37D1-EA1DF446-05B6-456C-97D8-25FB449BC510
The PFCW system operates at speeds
above approximately 3 MPH (5 km/h).
If there is a potential risk of a forward
collision, the PFCW system will warn the
driver by blinking the driver assist system
forward indicator and the vehicle ahead
detection indicator, and sounding an audible alert.
5-118
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(303,1)
TURNING THE PFCW SYSTEM ON/
OFF
CV37D1-AC33BAA4-A08F-4D5E-8D5B-266709EF42E4
Perform the following steps to turn the
PFCW system on or off.
3 and touch
1. Push the MENU button *
[Driver Assistance] on the lower display
2 .
*
2. Touch [Emergency Assist].
3. Touch [Forward emergency braking] to
turn the system ON/OFF.
When the PFCW system is turned off, the
1
FEB system warning light (orange) *
illuminates.
NOTE:
JVS0847X
1
*
2
*
3
*
The PFCW system is integrated into the
FEB system. There is not a separate
selection in the display for the PFCW
system. When the FEB system is turned
off, the PFCW system is also turned off.
FEB system warning light (on the
instrument panel)
Lower display
MENU button
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-119
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(304,1)
JVS0295X
JVS0296X
Illustration A
Illustration B
JVS0297X
Illustration C
5-120
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(305,1)
— Dirt, ice, snow or other material
covering the radar sensor
— Interference by other radar sources
— Snow or road spray from travelling
vehicles.
— Driving in a tunnel
— (Illustration B) When the vehicle
ahead is being towed.
— (Illustration C) When the distance to
the vehicle ahead is too close, the
beam of the radar sensor is obstructed.
JVS0298X
Illustration D
PFCW SYSTEM
LIMITATIONS
CV37D1-455C5B74-CB20-41CE-9FBC-56C07CE75995
WARNING
Listed below are the system limitations for
the PFCW system. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
.
The PFCW system cannot detect all
vehicles under all conditions.
.
The radar sensor does not detect the
following objects:
— (Illustration D) When driving on a
steep downhill slope or roads with
sharp curves.
— Pedestrians, animals or obstacles in
the roadway
— Oncoming vehicles
.
The system is designed to automatically
check the sensor’s functionality, within
certain limitations. The system may not
detect some forms of obstruction of the
sensor area such as ice, snow, stickers,
for example. In these cases, the system
may not be able to warn the driver
properly. Be sure that you check, clean
and clear the sensor area regularly.
.
Excessive noise will interfere with the
warning chime sound, and the chime
— Crossing vehicles
.
(Illustration A) The PFCW system does
not function when a vehicle ahead is a
narrow vehicle, such as a motorcycle.
.
The radar sensor may not detect a
vehicle ahead in the following conditions:
— Snow or heavy rain
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-121
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(306,1)
may not be heard.
JVS0848X
1
*
2
*
5-122
Condition:
FEB system warning light (on the
instrument panel)
Driver assist system forward indicator
(on the vehicle information display)
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(307,1)
SYSTEM TEMPORARILY UNAVAILABLE
CV37D1-0100C753-06FB-4D85-9B17-E76D054465AA
Condition CV37D1-9E802995-6589-4B23-BC31-E6A0AFC33535
A
When the radar sensor picks up interference from another radar source, making it
impossible to detect a vehicle ahead, the
PFCW system is automatically turned off.
1
The FEB system warning light (orange) *
and the driver assist system forward
2 will illuminate.
indicator (orange) *
Action to take:
When the above conditions no longer exist,
the PFCW system will resume automatically.
Condition CV37D1-663B1273-8225-4991-B047-0F1435F68733
B
When the sensor area of the front bumper
is covered with dirt or is obstructed,
making it impossible to detect a vehicle
ahead, the PFCW system is automatically
turned off. The FEB system warning light
1 and the driver assist system
(orange) *
2 will illumiforward indicator (orange) *
nate and the “front radar obstruction”
warning message will appear in the vehicle
information display.
Action to take:
1
If the FEB system warning light (orange) *
comes on, stop the vehicle in a safe place,
place the shift lever in the P (Park) position
and turn the engine off. Clean the radar
cover on the front grille with a soft cloth,
and restart the engine. If the FEB system
1 continues to illuminate,
warning light *
have the PFCW system checked. It is
recommended you visit an INFINITI retailer
for this service.
to illuminate, have the PFCW system
checked. It is recommended you visit an
INFINITI retailer for this service.
NOTE:
If the FEB system stops working, the PFCW
system will also stop working.
SYSTEM MALFUNCTION
CV37D1-D9B2EC55-89A2-4341-9CF7-2D5BDEAB1CCA
If the PFCW malfunctions, it will be turned
off automatically, a chime will sound, the
1 and
FEB system warning light (orange) *
the driver assist system forward indicator
2 will illuminate, and the system
(orange) *
“malfunction” message will appear in the
vehicle information display.
Action to take:
1
If the FEB system warning light (orange) *
comes on, stop the vehicle in a safe
location, turn the engine off and restart
the engine. If the warning light continues
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-123
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(308,1)
. Do not attach metallic objects near the
sensor area (brush guard, etc.). This
could cause failure or malfunction.
. Do not alter, remove or paint the front
bumper. It is recommended you contact
an INFINITI retailer before customizing
or restoring the front bumper.
FCC Notice:
1. This device may not cause interference,
and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
For USA:
JVS0869X
SYSTEM MAINTENANCE
CV37D1-BAD4D55B-052E-4186-8131-D6F260402C36
A is located behind the grille
The sensor *
of the front bumper.
To keep the system operating properly, be
sure to observe the following:
. Always keep the sensor area of the front
grille clean.
. Do not strike or damage the areas
around the sensor.
. Do not cover or attach stickers or similar
objects on the front bumper near the
sensor area. This could cause failure or
malfunction.
5-124
Condition:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
FCC Warning
Changes or modification not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(309,1)
BREAK-IN SCHEDULE
CV37D1-2249F48B-385B-4D71-BC10-1043B0481870
CAUTION
During the first 1,200 miles (2,000 km),
follow these recommendations to obtain
maximum engine performance and ensure
the future reliability and economy of your
new vehicle.
Failure to follow these recommendations
may result in shortened engine life and
reduced engine performance.
. Avoid driving for long periods at constant speed, either fast or slow. Do not
run the engine over 4,000 rpm.
. Do not accelerate at full throttle in any
gear.
. Avoid quick starts.
. Avoid hard braking as much as possible.
FUEL EFFICIENT DRIVING TIPS
CV37D1-E1459835-666E-4073-BC8E-722F7466CF82
Follow these easy-to-use Fuel Efficient
Driving Tips to help you achieve the most
fuel economy from your vehicle.
1. Use smooth accelerator and brake
pedal application.
. Avoid rapid starts and stops.
. Use smooth, gentle accelerator and
brake application whenever possible.
. Maintain constant speed while commuting and coast whenever possible.
2. Maintain constant speed.
. Look ahead to try and anticipate and
minimize stops.
. Synchronizing your speed with traffic lights allows you to reduce your
number of stops.
. Maintaining a steady speed can
minimize red light stops and improve fuel efficiency.
3. Use air conditioning (A/C) at higher
vehicle speeds.
. Below 40 MPH (64 km/h), it is more
efficient to open windows to cool the
vehicle due to reduced engine load.
. Above 40 MPH (64 km/h), it is more
efficient to use A/C to cool the
vehicle due to increased aerody-
.
namic drag.
Recirculating the cool air in the cabin
when the A/C is on reduces cooling
load.
4. Drive at economical speeds and distances.
. Observing the speed limit and not
exceeding 60 MPH (97 km/h) (where
legally allowed) can improve fuel
efficiency due to reduced aerodynamic drag.
. Maintaining a safe following distance behind other vehicles reduces
unnecessary braking.
. Safely monitoring traffic to anticipate changes in speed permits
reduced braking and smooth acceleration changes.
. Select a gear range suitable to road
conditions.
5. Use cruise control.
. Using cruise control during highway
driving helps maintain a steady
speed.
. Cruise control is particularly effective in providing fuel savings when
driving on flat terrains.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-125
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(310,1)
INCREASING FUEL ECONOMY
CV37D1-1588CA13-BA81-4DF3-B5D2-ECE86C6E9368
6. Plan for the shortest route.
. Utilize a map or navigation system to
determine the best route to save
time.
7. Avoid idling.
. Shutting off your engine when safe
for stops exceeding 30-60 seconds
saves fuel and reduces emissions.
.
When entering a hot vehicle, opening the windows will help to reduce
the inside temperature faster, resulting in reduced demand on your A/C
system.
8. Buy an automated pass for toll roads.
. Automated passes permit drivers to
use special lanes to maintain cruising speed through the toll and avoid
stopping and starting.
. Keep your engine tuned up.
. Follow the recommended scheduled
maintenance.
. Keep the tires inflated to the correct
pressure. Low tire pressure increases
tire wear and lowers fuel economy.
. Keep the wheels in correct alignment.
Improper alignment increases tire wear
and lowers fuel economy.
. Use the recommended viscosity engine
oil. (See “Engine oil and oil filter
recommendation” (P.10-7).)
9. Winter warm up.
. Limit idling time to minimize impact
to fuel economy.
. Vehicles typically need no more than
30 seconds of idling at start-up to
effectively circulate the engine oil
before driving.
. Your vehicle will reach its ideal
operating temperature more quickly
while driving versus idling.
10. Keeping your vehicle cool.
. Park your vehicle in a covered
parking area or in the shade whenever possible.
5-126
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(311,1)
INTELLIGENT ALL-WHEEL DRIVE (AWD) (if so
equipped)
CV37D1-1AAB6C12-0451-4A5D-9321-14244FF57EE4
If any malfunction occurs in the Intelligent
All-Wheel Drive (AWD) system while the
engine is running, warning messages
appear in the vehicle information display.
2 may appear while trying to free
warning *
a stuck vehicle due to increased oil
temperature. The driving mode may change
to Two-Wheel Drive (2WD). If this warning is
displayed, stop the vehicle with the engine
idling, as soon as it is safe to do so. Then if
the warning turns off, you can continue
driving.
3 may
The “Tire Size Incorrect” warning *
appear if there is a large difference
between the diameters of front and rear
wheels. Pull off the road in a safe area, with
the engine idling. Check that all tire sizes
are the same, that the tire pressure is
correct and that the tires are not excessively worn.
If any warning message continues to be
displayed, have your vehicle checked as
soon as possible. It is recommended you
visit an INFINITI retailer for this service.
JVS0228M
1 appears,
If the “AWD Error” warning *
there may be a malfunction in the Intelligent AWD system. Reduce vehicle speed
and it is recommended you have your
vehicle checked by an INFINITI retailer as
soon as possible.
The “AWD High Temp.” (high temperature)
WARNING
.
For AWD equipped vehicles, do not
attempt to raise two wheels off the
ground and shift the transmission to
any drive or reverse position with the
engine running. Doing so may result in
drivetrain damage or unexpected vehicle
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-127
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(312,1)
movement which could result in serious
vehicle damage or personal injury.
.
Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer (such
as the dynamometers used by some
states for emissions testing) or similar
equipment even if the other two wheels
are raised off the ground. Make sure that
you inform the test facility personnel
that your vehicle is equipped with AWD
before it is placed on a dynamometer.
Using the wrong test equipment may
result in drivetrain damage or unexpected vehicle movement which could
result in serious vehicle damage or
personal injury.
.
If the “AWD Error” warning remains on
after the above operation, have your
vehicle checked as soon as possible. It is
recommended you visit an INFINITI retailer for this service.
.
The power train may be damaged if you
continue driving with the “AWD Error”
warning on.
CAUTION
.
Do not operate the engine on a free roller
when any of the wheels are raised.
.
If the “AWD Error” warning appears
while driving there may be a malfunction
in the AWD system. Reduce the vehicle
speed and have your vehicle checked as
soon as possible. It is recommended you
visit an INFINITI retailer for this service.
5-128
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(313,1)
PARKING/PARKING ON HILLS
CV37D1-42DA8129-93DE-4DEE-B288-140B31DDEE66
to move unexpectedly or roll away and
result in an accident.
.
Make sure the automatic transmission
shift lever has been pushed as far
forward as it can go and cannot be
moved without depressing the foot
brake pedal.
1. Firmly apply the parking brake.
2. Move the shift lever to the P (Park)
position.
SD1006MA
WARNING
.
Do not stop or park the vehicle over
flammable materials such as dry grass,
waste paper or rags. They may ignite and
cause a fire.
.
Never leave the engine running while the
vehicle is unattended.
.
Do not leave children unattended inside
the vehicle. They could unknowingly
activate switches or controls. Unattended children could become involved
in serious accidents.
.
To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assistance of others or pets unattended in
your vehicle. Additionally, the temperature inside a closed vehicle on a warm
day can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
.
Safe parking procedures require that
both the parking brake be applied and
the transmission placed into P (Park).
Failure to do so could cause the vehicle
3. To help prevent the vehicle from rolling
into the street when parked on a
sloping drive way, it is a good practice
to turn the wheels as illustrated.
. HEADED DOWNHILL WITH CURB: *
1
Turn the wheels into the curb and
move the vehicle forward until the
curb side wheel gently touches the
curb.
. HEADED UPHILL WITH CURB: *
2
Turn the wheels away from the curb
and move the vehicle back until the
curb side wheel gently touches the
curb.
. HEADED UPHILL OR DOWNHILL, NO
3
CURB: *
Turn the wheels toward the side of
the road so the vehicle will move
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-129
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(314,1)
POWER STEERING
CV37D1-13F641F0-368A-48A0-9D8E-2887231D757B
away from the center of the road if it
moves.
ELECTRIC CV37D1-954E7407-D3D0-4BAE-ACE9-71FC0E73FBB1
POWER STEERING TYPE
4. Push the ignition switch to the OFF
position.
WARNING
.
.
If the engine is not running or is turned
off while driving, the power assist for the
steering will not work. Steering will be
harder to operate.
When the power steering warning light
illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of
the vehicle but the steering will be
harder to operate.
The electric power steering is designed to
provide power assist while driving to
operate the steering wheel with light force.
When the steering wheel is operated
repeatedly or continuously while parking
or driving at a very low speed, the power
assist for the steering wheel will be
reduced. This is to prevent overheating of
the electric power steering and protect it
from getting damaged. While the power
assist is reduced, steering wheel operation
will become heavy. When the temperature
of the electric power steering goes down,
the power assist level will return to normal.
5-130
Condition:
Avoid repeating such steering wheel operations that could cause the electric
power steering to overheat.
You may hear a sound when the steering
wheel is operated quickly. However, this is
not a malfunction.
If the power steering warning light illuminates while the engine is running, it may
indicate the electric power steering is not
functioning properly and may need servicing. It is recommended you have the
electric power steering checked by an
INFINITI retailer. (See “Power steering
warning light” (P.2-16).)
When the power steering warning light
illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of the
vehicle. However, greater steering effort is
needed, especially in sharp turns and at
low speeds.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(315,1)
HYDRAULIC PUMP ELECTRIC POWER
STEERING CV37D1-C72CEED9-2F86-476F-846E-D147F1020717
TYPE
WARNING
When the power steering warning light
illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of the
vehicle, but the steering will be much harder
to operate.
The hydraulic pump electric power steering
is designed to provide power assistance
while driving to operate the steering wheel
with light force.
When the steering wheel is operated
repeatedly or continuously while parking
or driving at a very low speed, the power
assist for the steering wheel will be
reduced. This is to prevent overheating of
the hydraulic pump electric power steering
and protect it from getting damaged. While
the power assist is reduced, steering wheel
operation will become heavy. If the steering wheel operation is still performed, the
power steering may stop and the power
steering warning light will illuminate. Stop
the engine and place the ignition switch in
the OFF position. The temperature of the
hydraulic pump electric power steering will
go down and the power assist level will
return to normal after starting the engine.
The power steering warning light will go
off. Avoid repeating such steering wheel
operations that could cause the hydraulic
pump electric power steering to overheat.
You may hear a noise from the front of the
vehicle when the steering wheel is operated. This is not a malfunction.
If the power steering warning light illuminates while the engine is running, it may
indicate the hydraulic pump electric power
steering is not functioning properly and
may need servicing. It is recommended you
have the hydraulic pump electric power
steering checked by an INFINITI retailer.
When the power steering warning light
illuminates with the engine running, the
power assist for the steering will cease
operation but you will still have control of
the vehicle. At this time, greater steering
efforts are required to operate the steering
wheel, especially in sharp turns and at low
speeds.
DIRECT ADAPTIVE
STEERING TYPE
CV37D1-BDA388DD-1664-4AC7-93EB-FFAD17252ACE
WARNING
.
When the power steering warning light
illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of
the vehicle, but the steering will be
harder to operate.
.
If wheels or tires other than the INFINITI
recommended ones are used, Direct
Adaptive Steering may not operate properly and the power steering warning
light may illuminate.
.
Do not modify the vehicle’s suspension.
If suspension parts such as shock
absorbers, struts, springs, stabilizer
bars, bushings and wheels are not
INFINITI recommended for your vehicle
or are extremely deteriorated, Direct
Adaptive Steering may not operate properly and the power steering warning
light may illuminate.
.
Do not modify the vehicle’s steering. If
steering parts are not INFINITI recommended for your vehicle or are extremely
deteriorated, Direct Adaptive Steering
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-131
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(316,1)
may not operate properly and the power
steering warning light may illuminate.
.
If the VDC warning light illuminates, the
power steering warning light may also
illuminate at the same time. Stop the
vehicle in a safe location, turn the engine
off and restart the engine. If the power
steering warning light continues to
illuminate, it is recommended you have
the system checked by an INFINITI
retailer. For VDC system, see “Vehicle
Dynamic Control (VDC) system” (P.5136).
CAUTION
.
Do not place the ignition switch is in the
ON position while the steering wheel or
a tire is removed.
.
Do not turn the steering wheel as much
as possible while the ignition switch is
in any position other than the ON
position.
.
Installing an accessory on the steering
wheel, or changing the steering wheel,
may reduce the steering performance.
5-132
Condition:
Direct Adaptive Steering is designed to
control the steering force and steering
angle according to the vehicle speed and
amount of turning of the steering wheel.
The steering characteristic can be selected
using the INFINITI Drive Mode Selector. See
“INFINITI Drive Mode Selector” (P.5-23).
If the VDC system is turned off, the setting
of steering becomes standard mode.
If the power steering warning light illuminates while the engine is running, it may
indicate that Direct Adaptive Steering is
not functioning properly and may need
servicing. It is recommended you have the
system checked by an INFINITI retailer. (See
“Power steering warning light” (P.2-16).)
When the power steering warning light
illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of the
vehicle. However, greater steering effort
will be needed, especially in sharp turns
and at low speeds.
If Direct Adaptive Steering is malfunctioning, the steering wheel may turn slightly
even when driving on a straight road.
Under the following conditions, the steering wheel may turn slightly even when
driving on a straight road. This is due to a
protection mechanism for Direct Adaptive
Steering. The steering wheel will return to
the normal position after the protection
mechanism is deactivated.
Condition A
. When the engine is stalled or likely to
be stalled
. When the steering wheel is held in the
full lock position or when the front tire
touches an obstruction.
. When the battery is discharged
To return the steering wheel to the normal
position, stop the vehicle in a safe location
and stop operating the steering wheel.
Then drive the vehicle for a short period of
time.
Condition B
. When the steering wheel is operated
repeatedly or continuously while parking or driving at a very low speed. In
this case, the power assist for the
steering wheel will be reduced.
To return the steering wheel to the normal
position, stop the vehicle in a safe location
and wait for a period of time, without
operating the steering wheel, until the
temperature of Direct Adaptive Steering
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(317,1)
BRAKE SYSTEM
CV37D1-86A44992-7267-42A5-98A1-F79018080BEF
cools down. Avoid repeated steering wheel
operations that could cause Direct Adaptive Steering to overheat.
When the vehicle is tested on the 2-wheel
dynamometer, the power steering warning
light may illuminate. To turn off the power
steering warning light, stop the vehicle in a
safe location, turn the engine off, restart
the engine, and then drive the vehicle for a
period of time.
driving on a straight road. To return
the steering wheel to the normal position, drive the vehicle on a straight road
for a period of time.
You may hear a noise under the following
conditions. However, this is not a malfunction.
. When the engine is started or stopped.
. When the steering wheel is turned in
the full lock position.
The following conditions do not indicate a
malfunction of Direct Adaptive Steering.
. You may notice wider steering play
when the ignition switch is in the OFF
or ACC position compared to when it is
in the ON position.
. After the engine is started, the steering
wheel may turn slightly even when
driving on a straight road. To return to
the normal position, drive the vehicle
on a straight road for a period of time.
. After the engine is started, the steering
wheel may move if the steering wheel
was turned to the fully locked position
while the ignition switch was in the OFF
position.
. After the vehicle is tested on the 4wheel dynamometer, the steering
wheel may turn slightly even when
BRAKING PRECAUTIONS
CV37D1-306DF583-15A7-4F2E-A62C-BF5322FC38D7
The brake system has two separate hydraulic circuits. If one circuit malfunctions,
you will still have braking at two wheels.
Vacuum assisted
brakes
CV37D1-78C52DD3-F84F-4DBD-A69F-5E2253E57FCE
The brake booster aids braking by using
engine vacuum. If the engine stops, you
can stop the vehicle by depressing the
brake pedal. However, greater foot pressure on the brake pedal will be required to
stop the vehicle and the stopping distance
will be longer.
Using theCV37D1-CBE6144D-573B-4C4C-8A27-7992EBD125D3
brakes
Avoid resting your foot on the brake pedal
while driving. This will cause overheating
of the brakes, wearing out the brake and
pads faster and reduce gas mileage.
To help save the brakes and to prevent the
brakes from overheating, reduce speed
and downshift to a lower gear before going
down a slope or long grade. Overheated
brakes may reduce braking performance
and could result in loss of vehicle control.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-133
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(318,1)
BRAKE ASSIST
CV37D1-F6785775-3925-43E5-BB5B-DA5F01739940
WARNING
.
While driving on a slippery surface, be
careful when braking, accelerating or
downshifting. Abrupt braking or accelerating could cause the wheels to skid
and result in an accident.
.
If the engine is not running or is turned
off while driving, the power assist for the
brakes will not work. Braking will be
harder.
PARKING CV37D1-8D2FFD7C-4467-45F7-A514-CBBDEBD1F7FB
BRAKE BREAK-IN
Break in the parking brake shoes whenever
the stopping effect of the parking brake is
weakened or whenever the parking brake
shoes and/or drums/rotors are replaced,
in order to assure the best braking
performance.
This procedure is described in the vehicle
service manual. It is recommended you
visit an INFINITI retailer for this service.
Wet brakes
CV37D1-4164933E-9063-4069-9B0B-00C0D135CBA1
When the vehicle is washed or driven
through water, the brakes may get wet.
As a result, your braking distance will be
longer and the vehicle may pull to one side
during braking.
Condition:
When the force applied to the brake pedal
exceeds a certain level, the Brake Assist is
activated generating greater braking force
than a conventional brake booster even
with light pedal force.
WARNING
The Brake Assist is only an aid to assist
braking operation and is not a collision
warning or avoidance device. It is the
driver’s responsibility to stay alert, drive
safely and be in control of the vehicle at all
times.
ANTI-LOCK
BRAKING SYSTEM (ABS)
CV37D1-AD17D48C-F86A-4373-A36D-8D191DFD4848
WARNING
To dry brakes, drive the vehicle at a safe
speed while lightly tapping the brake pedal
to heat-up the brakes. Do this until the
brakes return to normal. Avoid driving the
vehicle at high speeds until the brakes
function correctly.
5-134
BRAKE ASSIST
CV37D1-3F9393D9-D02F-4462-8A83-9E9A6FD7B50A
.
The Anti-lock Braking System (ABS) is a
sophisticated device, but it cannot prevent accidents resulting from careless or
dangerous driving techniques. It can
help maintain vehicle control during
braking on slippery surfaces. Remember
that stopping distances on slippery
surfaces will be longer than on normal
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(319,1)
surfaces even with ABS. Stopping distances may also be longer on rough,
gravel or snow covered roads, or if you
are using tire chains. Always maintain a
safe distance from the vehicle in front of
you. Ultimately, the driver is responsible
for safety.
.
Tire type and condition may also affect
braking effectiveness.
— When replacing tires, install the
specified size of tires on all four
wheels.
— When installing a spare tire, make
sure that it is the proper size and
type as specified on the Tire and
Loading Information label. See “Tire
and loading information label” (P.1014) of this manual.
— For detailed information, see
“Wheels and tires” (P.8-33) of this
manual.
The Anti-lock Braking System (ABS) controls the brakes so the wheels do not lock
during hard braking or when braking on
slippery surfaces. The system detects the
rotation speed at each wheel and varies
the brake fluid pressure to prevent each
wheel from locking and sliding. By preventing each wheel from locking, the
system helps the driver maintain steering
control and helps to minimize swerving
and spinning on slippery surfaces.
Using theCV37D1-5E51FABB-C166-46FD-896A-2D2AFBB568C6
system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady
pressure, but do not pump the brakes. The
ABS will operate to prevent the wheels
from locking up. Steer the vehicle to avoid
obstacles.
tion in the brake pedal. This is normal and
does not indicate a malfunction. If the
computer senses a malfunction, it switches
the ABS off and illuminates the ABS
warning light on the instrument panel.
The brake system then operates normally,
but without anti-lock assistance.
If the ABS warning light illuminates during
the self-test or while driving, have the
vehicle checked. It is recommended you
visit an INFINITI retailer for this service.
Normal operation
CV37D1-97EC20E5-32E3-4D14-80B0-197E7EAA54F0
The ABS operates at speeds above 3 to 6
MPH (5 to 10 km/h).
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test feature
CV37D1-9FAB00BB-F2BE-4168-BD75-236754B398C1
The ABS includes electronic sensors, electric pumps, hydraulic solenoids and a
computer. The computer has a built-in
diagnostic feature that tests the system
each time you start the engine and move
the vehicle at a low speed in forward or
reverse. When the self-test occurs, you may
hear a “clunk” noise and/or feel a pulsa-
When the ABS senses that one or more
wheels are close to locking up, the actuator
rapidly applies and releases hydraulic
pressure. This action is similar to pumping
the brakes very quickly. You may feel a
pulsation in the brake pedal and hear a
noise from under the hood or feel a
vibration from the actuator when it is
operating. This is normal and indicates
that the ABS is operating properly. However, the pulsation may indicate that road
conditions are hazardous and extra care is
required while driving.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-135
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(320,1)
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM
CV37D1-4A9596A2-6386-4C22-A04D-18A64B158580
The Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver
inputs and vehicle motion. Under certain
driving conditions, the VDC system helps
to perform the following functions.
. Controls brake pressure to reduce
wheel slip on one slipping drive wheel
so power is transferred to a non
slipping drive wheel on the same axle.
. Controls brake pressure and engine
output to reduce drive wheel slip based
on vehicle speed (traction control function).
. Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle in
the following conditions:
— understeer (vehicle tends to not
follow the steered path despite
increased steering input)
— oversteer (vehicle tends to spin due
to certain road or driving conditions).
The VDC system can help the driver to
maintain control of the vehicle, but it
cannot prevent loss of vehicle control in
all driving situations.
When the VDC system operates, the VDC
warning light
in the instrument panel
5-136
Condition:
flashes so note the following:
. The road may be slippery or the system
may determine some action is required
to help keep the vehicle on the steered
path.
. You may feel a pulsation in the brake
pedal and hear a noise or vibration
from under the hood. This is normal and
indicates that the VDC system is working properly.
. Adjust your speed and driving to the
road conditions.
See “Vehicle Dynamic Control (VDC) warning light” (P.2-18).
If a malfunction occurs in the system, the
VDC warning light
illuminates in the
instrument panel. The VDC system automatically turns off.
The VDC OFF switch is used to turn off the
VDC system. The VDC off indicator light
illuminates to indicate the VDC system is
off. When the VDC switch is used to turn off
the system, the VDC system still operates
to prevent one drive wheel from slipping by
transferring power to a non slipping drive
wheel. The VDC warning light
flashes if
this occurs. All other VDC functions are off,
except for brake force distribution, and the
VDC warning light
will not flash. The
VDC system is automatically reset to on
when the ignition switch is placed in the
OFF position then back in the ON position.
See “Vehicle Dynamic Control (VDC) warning light” (P.2-18) and “Vehicle Dynamic
Control (VDC) off indicator light” (P.2-20).
The computer has a built-in diagnostic
feature that tests the system each time you
start the engine and move the vehicle
forward or in reverse at a slow speed. When
the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in
the brake pedal. This is normal and is not
an indication of a malfunction.
VDC operation is reduced when the INFINITI
Drive Mode Selector is used to select the
SPORT+ mode (if so equipped). The VDC
system may not operate in the same
circumstances when compared to operation in the standard mode. To help prevent
accidents drive carefully, avoid careless or
dangerous driving techniques and be
especially careful when driving and cornering on slippery surfaces.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(321,1)
BRAKE FORCE
DISTRIBUTION
CV37D1-5B46CABC-FBC6-4BB8-9C50-B12A7A558D2E
During braking while driving through turns,
the system optimizes the distribution of
force to each of the four wheels depending
on the radius of the turn.
performance, and the VDC warning light
may illuminate.
.
If brake related parts such as brake
pads, rotors and calipers are not INFINITI
recommended or are extremely deteriorated, the VDC system may not operate
properly and the VDC warning light
may illuminate.
.
If engine control related parts are not
INFINITI recommended or are extremely
deteriorated, the VDC warning light
may illuminate.
.
When driving on extremely inclined
surfaces such as higher banked corners,
the VDC system may not operate properly and the VDC warning light
may
illuminate. Do not drive on these types of
roads.
.
When driving on an unstable surface
such as a turntable, ferry, elevator or
ramp, the VDC warning light
may
illuminate. This is not a malfunction.
Restart the engine after driving onto a
stable surface.
.
If wheels or tires other than the INFINITI
recommended ones are used, the VDC
system may not operate properly and the
VDC warning light
may illuminate.
WARNING
.
.
.
The VDC system is designed to help the
driver maintain stability but does not
prevent accidents due to abrupt steering
operation at high speeds or by careless
or dangerous driving techniques. Reduce
vehicle speed and be especially careful
when driving and cornering on slippery
surfaces and always drive carefully.
The brake force distribution system may
not be effective depending on the driving
condition. Always drive carefully and
attentively.
Do not modify the vehicle’s suspension.
If suspension parts such as shock
absorbers, struts, springs, stabilizer
bars, bushings and wheels are not
INFINITI recommended for your vehicle
or are extremely deteriorated, the VDC
system may not operate properly. This
could adversely affect vehicle handling
.
The VDC system is not a substitute for
winter tires or tire chains on a snow
covered road.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-137
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(322,1)
ACTIVE TRACE CONTROL
CV37D1-B5B4CBB7-02DE-42E3-B478-AAEA8DEBF723
This system senses driving based on the
driver’s steering and acceleration/braking
patterns, and controls brake pressure at
individual wheels to help smooth vehicle
response.
When the SPORT mode is selected by the
INFINITI Drive Mode Selector, the amount of
brake control provided by the active trace
control is reduced.
When the PERSONAL mode is selected, the
active trace control can be set to ON
(enabled) or OFF (disabled). See “INFINITI
Drive Mode Selector” (P.5-23).
When the VDC OFF switch is used to turn off
the VDC system, the active trace control is
also turned off.
JVS0249X
When the active trace control is operated
and the “Chassis Control” mode is selected
in the trip computer, the active trace
control graphics are shown in the vehicle
information display. (See “Trip computer”
(P.2-31).)
If the chassis control warning message
appears in the vehicle information display,
it may indicate that the active trace control
is not functioning properly. It is recommended you have the system checked by
an INFINITI retailer. (See “27. Chassis
control warning” (P.2-26).)
5-138
Condition:
WARNING
The active trace control may not be effective
depending on the driving condition. Always
drive carefully and attentively.
When the active trace control is operating,
you may feel a pulsation in the brake pedal
and hear a noise. This is normal and
indicates that the active trace control is
operating properly.
Even if the active trace control is set to OFF,
some functions will remain on to assist the
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(323,1)
HILL START ASSIST SYSTEM
CV37D1-B2E44199-DFC9-456A-A2F7-D14ECC3D735F
driver (for example, avoidance scenes).
WARNING
.
.
.
Never rely solely on the hill start assist
system to prevent the vehicle from
moving backward on a hill. Always drive
carefully and attentively. Depress the
brake pedal when the vehicle is stopped
on a steep hill. Be especially careful
when stopped on a hill on frozen or
muddy roads. Failure to prevent the
vehicle from rolling backwards may
result in a loss of control of the vehicle
and possible serious injury or death.
The hill start assist system is not
designed to hold the vehicle at a
standstill on a hill. Depress the brake
pedal when the vehicle is stopped on a
steep hill. Failure to do so may cause the
vehicle to roll backwards and may result
in a collision or serious personal injury.
The hill start assist system may not
prevent the vehicle from rolling backwards on a hill under all load or road
conditions. Always be prepared to depress the brake pedal to prevent the
vehicle from rolling backwards. Failure to
do so may result in a collision or serious
personal injury.
The hill start assist system automatically
keeps the brakes applied to help prevent
the vehicle from rolling backwards in the
time it takes the driver to release the brake
pedal and apply the accelerator when the
vehicle is stopped on a hill.
The hill start assist system will operate
automatically under the following conditions:
. The transmission is shifted to a forward
or reverse gear.
. The vehicle is stopped completely on a
hill by applying the brake.
The maximum holding time is 2 seconds.
After 2 seconds the vehicle will begin to
roll back and the hill start assist system
will stop operating completely.
The hill start assist system will not operate
when the transmission is shifted to the N
(Neutral) or P (Park) position or on a flat
and level road.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-139
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(324,1)
CHASSIS CONTROL
IDLING STOP SYSTEM (if so equipped)
CV37D1-3A4379DD-9A3F-49A7-ADE1-B80EAEF92E63
CV37D1-43DF349A-25FA-4A2E-88D6-B2F437212C21
The chassis control is an electric control
module that includes the following functions:
The Idling Stop System activates to prevent
unnecessary fuel consumption, exhaust
emissions and noise.
. Log-in function (See “Log-in function”
(P.3-16).)
. INFINITI Drive Mode Selector (See
“INFINITI Drive Mode Selector” (P.523).)
. Active Lane Control (if so equipped)
(See “Active Lane Control” (P.5-27).)
. Active Trace Control (See “Active trace
control” (P.5-138).)
. When you fully depress the brake pedal
to stop the vehicle, the engine is turned
off automatically.
. When you release the brake pedal to
begin moving again, the engine is
turned on automatically.
WARNING
The engine restarts if the vehicle moves at
approximately 1 MPH (2 km/h) or more (on a
downhill grade, etc.), while the engine is
turned off by the Idling Stop System.
Depress the brake pedal immediately to
stop the vehicle to prevent an accident.
CAUTION
At the end of the journey the engine must be
stopped and ignition switch be turned off.
Lock the vehicle as normal. Turning the
ignition switch OFF will shut down all
electrical systems. Failure to do this may
result in a discharged battery.
5-140
Condition:
NOTE:
The Idling Stop System will not activate
under the following conditions:
. when the engine is kept idling without
the vehicle being driven after the
engine is turned on.
. when the engine coolant temperature is
low.
. when the battery capacity is low.
. when the battery temperature is low or
extremely high.
. when the vehicle is moving.
. when a negative pressure booster
decreases.
. when the engine hood is opened with
the engine running.
. when the engine is turned on with the
engine hood open.
. when the driver’s seat belt is not
fastened.
. when the driver’s door is open.
. when the steering wheel is operated.
. when the angle of steering wheel is not
straight.
. when the Idling Stop System indicator
blinks at a low speed.
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(325,1)
. when the fan speed control is in any
position other than “OFF” (0) while the
air flow control is in the front defroster
position.
. when the front defroster switch is on.
. when the rear window defroster switch
is on.
. When the temperature inside the vehicle is lower than approximately 688F
(208C).
. When the temperature inside the vehicle is higher than approximately 868F
(308C). (When the air conditioner is off,
the Idling Stop System will operate.)
. When the fan speed of the air conditioner is set to the maximum speed.
. when the Idling Stop OFF switch is
turned on.
. when the power consumption is large.
. when the vehicle is traveling at altitudes higher than 8,203 ft (2,500 m).
. when the accelerator pedal is depressed.
. when the shift lever is in the R
(Reverse) position.
. when the brake pedal is not firmly
depressed.
. when stopping the vehicle on steep
sloping roads.
NOTE:
The engine will not restart even if the
brake pedal is released while the Idling
Stop System is activated when the shift
lever is in the P (Park) position.
NOTE:
It may take some time until the Idling Stop
System activates under the following
conditions:
. when the battery is discharged.
. when the outside temperature is low or
high.
. when the battery is replaced or the
battery terminal is disconnected for
extended periods and then reconnected.
NOTE:
When the Idling Stop System indicator
light illuminates, the engine starts running automatically under at least one of
the following conditions:
. The brake pedal is released with the
shift lever in the D (Drive) or N (Neutral)
position.
. The shift lever is placed in the D (Drive)
or R (Reverse) position from the N
(Neutral) or P (Park) position.
. The driver’s seat belt is unfastened, or
the driver’s door is open.
. The battery voltage becomes low (due
to electrical load from other vehicle
systems like headlights, heaters, etc.,
or auxiliary devices connected to the
12 volt socket inside the vehicle).
. The vehicle speed is above about 1
MPH (2 km/h).
. The front defroster is operated.
. The rear window defroster is operated.
. When the temperature inside the vehicle is lower than approximately 688F
(208C).
. When the temperature inside the vehicle is higher than approximately 868F
(308C). (When the air conditioner is off,
the Idling Stop System will operate.)
. When the front defroster is turned on.
(The engine may not starts depending
on the outside temperature.)
. When more than 3 minutes have
elapsed since the Idling Stop System
was active.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-141
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(326,1)
. When the accelerator pedal is depressed.
. When the steering wheel is operated.
(The steering wheel operation may
become heavy, but this is not a
malfunction.)
. When the battery capacity is low.
. When the power consumption is high.
. When the shift lever is placed in the R
(Reverse) position.
NOTE:
RETROGRADE MOVEMENT CONTROL
FUNCTIONCV37D1-840590D2-3851-487C-AE46-349B1C43B67B
This system is designed to reduce the
retrograde movement that occurs while the
driver’s foot changes from depressing the
brake pedal to the accelerator pedal when
moving the vehicle while the Idling Stop
System is active on a hilly road.
IDLING STOP
SYSTEM DISPLAY
CV37D1-EFDD0118-4664-42D7-80C4-6E7CF8F2FBDE
The status of the Idling Stop System can be
checked in the vehicle information display.
The following condition will prevent the
Idling Stop System from automatically
restarting the engine. Starting the engine
with the ignition switch operation is then
necessary:
. The hood is open.
JVS0342X
Idling Stop
System ON or OFF
CV37D1-58B5218C-D477-41D2-9858-789FD6A2D9E8
If the Idling Stop System is activated or
deactivated using the Idling Stop OFF
switch, the message is shown.
Use this system while waiting at stoplight,
etc. When the vehicle is stopped for long
periods of time, turn off the engine.
When the engine is stopped by the Idling
Stop System, heating, cooling and dehumidifying functions will be deactivated. To
avoid the air conditioning functions from
being deactivated, turn off the Idling Stop
mode by pushing the Idling Stop OFF
switch.
5-142
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(327,1)
Total fuel saved and engine stop time” (P.232).
JVS0904X
JVS0344X
Fuel saved
and engine stop time
CV37D1-10BC0B92-4B0C-4200-91F2-3BB24862FC63
Auto startCV37D1-ED4F41FF-44B6-4633-B680-E7D7D3965E0E
deactivation
The fuel saved and the engine stop time
mode shows the following items:
If the engine stops when the Idling Stop
System is activated, and will not start
automatically, the message is shown.
. The fuel saved shows the estimated
quantity of fuel that were saved by the
Idling Stop System every time the
engine is automatically stopped.
. The engine stop time shows the time
that the engine has been stopped for by
the Idling Stop System.
The total fuel saved and the engine stop
time can also be checked in the vehicle
information display. See “4. Trip fuel saved
and engine stop time” (P.2-31) and “5.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-143
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(328,1)
JVS0345X
JVS0346X
JVS0269X
Key LOCKCV37D1-A566FE73-9718-453C-9CA0-F65E2D0B47CE
warning
System fault
CV37D1-57B6D91E-99FE-4EEE-84D0-768E7BA4541C
IDLING STOP
OFF SWITCH
CV37D1-E580400F-6BFA-43E8-9CC0-585417DBB02B
The information is displayed and a buzzer
sounded to remind the driver to place the
ignition switch in the OFF position to avoid
a discharged battery.
This message is displayed when the Idling
Stop System is malfunctioning.
The system can be temporarily deactivated
by pushing the Idling Stop OFF switch.
Pushing the switch again or restarting the
engine by using the ignition switch will
reactivate the Idling Stop System.
It is recommended you have the system
checked by an INFINITI retailer.
The message can be cleared by placing the
ignition switch in the OFF position (or
restarting the engine) or pushing the
or
switch on the steering wheel.
5-144
Condition:
. When the Idling Stop System is deactivated while the engine is running, the
engine is prevented from automatically
stopping.
. When the Idling Stop System is deactivated after the engine has been automatically stopped by the Idling Stop
System, the engine will immediately
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(329,1)
COLD WEATHER DRIVING
CV37D1-001CE61A-44FC-4E4D-95F7-8EE61107147D
restart if suitable conditions are present. The engine will then be prevented
from automatically stopping during the
same journey.
. Whenever the Idling Stop System is
1 on
deactivated the indicator light *
the Idling Stop OFF switch illuminates.
In this condition the Idling Stop System
cannot prevent unnecessary fuel consumption, exhaust emissions, or noise
during your journey.
. If the Idling Stop System is malfunction1 on the Idling
ing, the indicator light *
Stop OFF switch illuminates.
NOTE:
The Idling Stop System ON or OFF message
is displayed for a few seconds in the
vehicle information display when the
Idling Stop OFF switch is pushed. See
“Idling Stop System ON or OFF” (P.5-142).
FREEING CV37D1-5EBECC5D-B5CD-4CE7-A4D7-6E52DD8EBEEC
A FROZEN DOOR LOCK
To prevent a door lock from freezing, apply
deicer through the key hole. If the lock
becomes frozen, heat the key before
inserting it into the key hole or use the
Intelligent Key system.
ANTIFREEZE
CV37D1-7CABC06B-2D45-45D5-A042-B13E6F03CC5E
In the winter when it is anticipated that the
outside temperature will drop below 328F
(08C), check antifreeze to assure proper
winter protection. For additional information, see “Engine cooling system (for
VR30DDTT engine models)” (P.8-6), “Engine cooling system (for 2.0L turbo gasoline engine models)” (P.8-8) or “Intercooler
cooling system (for VR30DDTT engine
models)” (P.8-9).
BATTERY
CV37D1-48005E45-813C-44A5-8D41-9521223F2001
If the battery is not fully charged during
extremely cold weather conditions, the
battery fluid may freeze and damage the
battery. To maintain maximum efficiency,
the battery should be checked regularly.
For additional information, see “Battery”
(P.8-17).
DRAININGCV37D1-A0F702CC-5DF7-4D12-BDDC-B53438BDF4C1
OF COOLANT WATER
If the vehicle is to be left outside without
antifreeze, drain the cooling system, including the engine block. Refill before
operating the vehicle. For details, see
“Engine cooling system (for VR30DDTT
engine models)” (P.8-6) or “Engine cooling
system (for 2.0L turbo gasoline engine
models)” (P.8-8).
TIRE EQUIPMENT
CV37D1-B6FA169D-58DD-435F-9AD5-F0E503886684
SUMMER tires have a tread designed to
provide superior performance on dry pavement. However, the performance of these
tires will be substantially reduced in snowy
and icy conditions. If you operate your
vehicle on snowy or icy roads, INFINITI
recommends the use of MUD & SNOW or
ALL SEASON tires on all four wheels. It is
recommended you consult an INFINITI
retailer for the tire type, size, speed rating
and availability information.
For additional traction on icy roads,
studded tires may be used. However, some
U.S. states and Canadian provinces prohibit their use. Check local, state and
provincial laws before installing studded
tires.
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-145
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(330,1)
Skid and traction capabilities of studded
snow tires, on wet or dry surfaces, may be
poorer than that of non-studded snow
tires.
Tire chains may be used. For details, see
“Tire chains” (P.8-41) of this manual.
DRIVING ON
SNOW OR ICE
CV37D1-66431155-62BF-4354-8807-8F4097602234
WARNING
.
Intelligent All-Wheel Drive (AWD)
models CV37D1-52FA104E-DAD0-44AC-B200-A57E40801427
If you install snow tires, they must also be
the same size, brand, construction and
tread pattern on all four wheels.
.
SPECIAL WINTER
EQUIPMENT
CV37D1-FD3A51BB-C337-4BB2-A247-49F856B8CB20
It is recommended that the following items
be carried in the vehicle during winter:
. A scraper and stiff-bristled brush to
remove ice and snow from the windows
and wiper blades.
. A sturdy, flat board to be placed under
the jack to give it firm support.
. A shovel to dig the vehicle out of
snowdrifts.
. Extra window washer fluid to refill the
reservoir tank.
Condition:
Whatever the condition, drive with caution. Accelerate and slow down with
care. If accelerating or downshifting too
fast, the drive wheels will lose even more
traction.
.
Allow more stopping distance under
these conditions. Braking should be
started sooner than on dry pavement.
.
Allow greater following distances on
slippery roads.
.
Watch for slippery spots (glare ice).
These may appear on an otherwise clear
road in shaded areas. If a patch of ice is
seen ahead, brake before reaching it. Try
not to brake while on the ice, and avoid
any sudden steering maneuvers.
.
5-146
Wet ice (328F, 08C and freezing rain),
very cold snow or ice can be slick and
very hard to drive on. The vehicle will
have much less traction or “grip” under
these conditions. Try to avoid driving on
wet ice until the road is salted or sanded.
Do not use the cruise control on slippery
roads.
.
Snow can trap dangerous exhaust gases
under your vehicle. Keep snow clear of
the exhaust pipe and from around your
vehicle.
ENGINE BLOCK HEATER (if so
equipped)CV37D1-F270A1FF-C9B0-43A5-AB8A-F0C23F1ADF65
Engine block heaters are used to assist in
cold temperature starting.
The engine block heater should be used
when the outside temperature is 208F
(−78C) or lower.
To use theCV37D1-79B81556-127B-4048-8AA9-6FD28CD83F1B
engine block heater
1. Turn the engine off.
2. Open the hood and unwrap the engine
block heater cord.
3. Plug the engine block heater cord into a
grounded 3-wire, 3-pronged extension
cord.
4. Plug the extension cord into a Ground
Fault Interrupt (GFI) protected,
grounded 110-volt AC (VAC) outlet.
5. The engine block heater must be
plugged in for at least 2 - 4 hours,
depending on outside temperatures, to
properly warm the engine coolant. Use
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(331,1)
ACTIVE NOISE CANCELLATION/ACTIVE
SOUND ENHANCEMENT
CV37D1-1E92F145-B0EE-4AD1-8665-57B7AE39B0BA
an appropriate timer to turn the engine
block heater on.
6. Before starting the engine, unplug and
properly store the cord to keep it away
from moving parts.
WARNING
.
Do not use your engine block heater with
an ungrounded electrical system or a 2pronged adapter. You can be seriously
injured by an electrical shock if you use
an ungrounded connection.
.
Disconnect and properly store the engine block heater cord before starting
the engine. Damage to the cord could
result in an electrical shock and can
cause serious injury.
.
Use a heavy-duty 3-wire, 3-pronged
extension cord rated for at least 10A.
Plug the extension cord into a Ground
Fault Interrupt (GFI) protected, grounded
110-VAC outlet. Failure to use the proper
extension cord or a grounded outlet can
result in a fire or electrical shock and
cause serious personal injury.
JVS0905X
NOTE:
To operate the active noise cancellation
and active sound enhancement system
properly:
. Do not cover the speakers or woofer.
. Do not cover the microphones.
. Do not change or modify speakers
including the woofer and any audio
related parts such as the amplifier.
. Do not make any modification including
sound deadening or modifications
Starting and driving
Condition:
[ Edit: 2016/ 4/ 27
5-147
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(332,1)
around the microphones, speakers or
woofer.
ACTIVE NOISE
CANCELLATION
CV37D1-E5B2A5E3-5DE7-405B-A503-9DEA588404AA
The active noise cancellation uses micro1 located inside the vehicle to
phones *
detect engine booming noises. The system
then automatically produces a muted engine booming noise through the speakers
2 , *
4
5
(if so equipped), *
(if so
*
3 to reduce engine
equipped) and woofer *
booming noise.
1 or the area around it
If the microphone *
is tapped, abnormal noise may be output
from the speaker.
ACTIVE SOUND
ENHANCEMENT
CV37D1-02F77BCA-6301-45D8-B951-7187C1D09D10
The active sound enhancement generates
sounds according to engine speed and
2
driving modes through the speakers *
5 (if so equipped) to enhance the
and *
quality of the engine sound.
5-148
Condition:
Starting and driving
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(333,1)
6 In case of emergency
Hazard warning flasher switch ............................
...
Roadside assistance program .............................
...
Emergency engine shut off ..................................
...
Flat tire ...............................................................
...
Tire Pressure Monitoring System (TPMS) .........
...
Run-flat tires ..................................................
...
Changing a flat tire .........................................
...
6-2
6-2
6-3
6-3
6-3
6-4
6-4
Jump starting ...................................................
...
Main battery (for all models) .......................
...
Auxiliary battery (for 2.0L turbo gasoline
engine models) ...........................................
...
Push starting ...................................................
...
If your vehicle overheats ..................................
...
Towing your vehicle ..........................................
...
Towing recommended by INFINITI ................
...
Vehicle recovery (freeing a stuck vehicle) ....
...
6-10
6-12
6-14
6-16
6-16
6-17
6-18
6-19
** Click HERE to see "Owner's Manual Supplement" **
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(334,1)
HAZARD WARNING FLASHER SWITCH
ROADSIDE ASSISTANCE PROGRAM
CV37D1-607A6196-FD87-446A-AE94-F5E9906886A3
CV37D1-09C9882C-8E70-4713-8807-D4CA17DB80BA
.
Turn signals do not work when the
hazard warning flasher lights are on.
The flasher can be actuated with the
ignition switch in any position.
In the event of a roadside emergency,
Roadside Assistance Service is available to
you. Please refer to your Warranty Information Booklet (U.S.) or Warranty & Roadside
Assistance Information Booklet (Canada)
for details.
When an impact that could activate the
supplemental air bags is detected, the
hazard warning flasher lights blink automatically. If the hazard warning flasher
switch is pushed, the hazard warning
flashers will turn off.
SIC2574
Push the switch on to warn other drivers
when you must stop or park under emergency conditions. All turn signal lights will
flash.
WARNING
.
If stopping for an emergency, be sure to
move the vehicle well off the road.
.
Do not use the hazard warning flashers
while moving on the highway unless
unusual circumstances force you to drive
so slowly that your vehicle might become a hazard to other traffic.
WARNING
Do not turn the hazard warning flasher
switch to off until you can make sure that it
is safe to do so. Also, the hazard flasher
warning may not blink automatically depending on the force of impact.
Some state laws may prohibit the use of
the hazard warning flasher switch while
driving.
6-2 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(335,1)
EMERGENCY ENGINE SHUT OFF
FLAT TIRE
CV37D1-63E297C5-4018-4F40-92EF-3B211665C34B
CV37D1-6C3D919A-CD26-4BC0-9CF9-2EC5F910E687
To shut off the engine in an emergency
situation while driving, perform the following procedure:
If you have a flat tire, follow the instructions in this section.
. Rapidly push the push-button ignition
switch 3 consecutive times in less than
1.5 seconds, or
. Push and hold the push-button ignition
switch for more than 2 seconds.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
CV37D1-BFEA3614-E51F-4536-91BF-65C5324E7C3E
use.
.
If the low tire pressure warning light
illuminates while driving, avoid sudden
steering maneuvers or abrupt braking,
reduce vehicle speed, pull off the road to
a safe location and stop the vehicle as
soon as possible. Driving with underinflated tires may permanently damage
the tires and increase the likelihood of
tire failure. Serious vehicle damage
could occur and may lead to an accident
and could result in serious personal
injury. Check the tire pressure for all
four tires. Adjust the tire pressure to the
recommended COLD tire pressure shown
on the Tire and Loading Information
label to turn the low tire pressure
warning light OFF. If the light still
illuminates while driving after adjusting
the tire pressure, a tire may be flat. If you
have a flat tire, replace it with a spare
tire (if so equipped).
.
Since the spare tire is not equipped with
the TPMS, when a spare tire is mounted
or a wheel is replaced, the TPMS will not
function and the low tire pressure warning light will flash for approximately 1
minute. The light will remain on after 1
minute. Have your tires replaced and/or
This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS). It
monitors tire pressure of all tires except
the spare. When the low tire pressure
warning light is lit and the “Tire Pressure
Low - Add Air” warning appears in the
vehicle information display, one or more of
your tires is significantly under-inflated. If
the vehicle is being driven with low tire
pressure, the TPMS will activate and warn
you of it by the low tire pressure warning
light. This system will activate only when
the vehicle is driven at speeds above 16
MPH (25 km/h). For more details, see
“Warning lights, indicator lights and audible reminders” (P.2-12) and “Tire Pressure
Monitoring System (TPMS)” (P.5-5).
WARNING
.
Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufacturer for the possible influences before
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(336,1)
TPMS system reset as soon as possible.
It is recommended you visit an INFINITI
retailer for these services.
.
.
distance at high speeds may damage
the tires.
.
Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
Do not inject any tire liquid or aerosol
tire sealant into the tires, as this may
cause a malfunction of the tire pressure
sensors.
.
RUN-FLAT TIRES
CV37D1-EFFD5D09-9FE8-41FE-8289-04B035B85902
Run-flat tires are those tires that can be
used temporarily if they are punctured. See
“Run-flat tires” (P.8-40).
.
Also, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the INFINITI Warranty
Information Booklet.
WARNING
.
6-4
Although you can continue driving with a
punctured run-flat tire, remember that
vehicle handling stability is reduced,
which could lead to an accident and
personal injury. Also, driving a long
Do not drive at speeds above 50 MPH (80
km/h) and do not drive more than
approximately 93 miles (150 km) with a
punctured run-flat tire. The actual distance the vehicle can be driven on a flat
tire depends on outside temperature,
vehicle load, road conditions and other
factors.
Drive safely at reduced speeds. Avoid
hard cornering or braking, which may
cause you to lose control of the vehicle.
If you detect any unusual sounds or
vibrations while driving with a punctured
run-flat tire, pull off the road to a safe
location and stop the vehicle as soon as
possible. The tire may be seriously
damaged and need to be replaced.
vehicle and the ground is smaller than
normal.
.
Do not enter an automated car wash with
a punctured run-flat tire.
.
It is recommended you have the punctured tire inspected by an INFINITI retailer
or other authorized repair shop. Replace
the tire as soon as possible if the tire is
seriously damaged.
CHANGINGCV37D1-7DC62245-C197-46D2-A590-2F8EFA714154
A FLAT TIRE
If you have a flat tire, follow the instructions in this section to replace the tire with
a spare tire (if so equipped). For the
vehicles with run-flat tires, you can continue driving to a safe location even if they
are punctured. (See “Run-flat tires” (P.6-4)
and “Run-flat tires” (P.8-40).)
This section also contains the information
about the vehicle jack-up procedures.
CAUTION
.
Never install tire chains on a punctured
run-flat tire, as this could damage your
vehicle.
.
Avoid driving over any projection or
pothole, as the clearance between the
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(337,1)
Stopping the
vehicle
CV37D1-C8BD7909-E246-4314-8B03-44AE22872067
sional road assistance.
1. Safely move the vehicle off the road
and away from traffic.
2. Turn on the hazard warning flashers.
3. Park on a level surface and apply the
parking brake. Move the shift lever to
the P (Park) position.
4. Turn off the engine.
5. Raise the hood to warn other traffic,
and to signal professional road assistance personnel that you need assistance.
MCE0001A
6. Have all passengers get out of the
vehicle and stand in a safe place, away
from traffic and clear of the vehicle.
Blocking wheels
CV37D1-4A169BFB-2170-457B-BD05-FE37E61C1616
1 at both the front
Place suitable blocks *
and back of the wheel diagonally opposite
the flat tire to prevent the vehicle from
moving when it is jacked up.
WARNING
.
Make sure the parking brake is securely
applied and the automatic transmission
into P (Park).
.
Never change tires when the vehicle is
on a slope, ice or slippery areas. This is
hazardous.
.
Never change tires if oncoming traffic is
close to your vehicle. Wait for profes-
WARNING
Be sure to block the wheel as the vehicle
may move and result in personal injury.
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(338,1)
Jacking up the vehicle and removing the damaged
tire
CV37D1-0BEFC529-EB0A-438D-A226-A026984E213D
WARNING
.
Never get under the vehicle while it is
supported only by the jack. If it is
necessary to work under the vehicle,
support it with safety stands.
.
Use only the jack provided with your
vehicle to lift the vehicle. Do not use the
jack provided with your vehicle on other
vehicles. The jack is designed for lifting
only your vehicle during a tire change.
.
Use the correct jack-up points. Never use
any other part of the vehicle for jack
support.
Remove jacking tools located inside the
trunk as illustrated.
.
Never jack up the vehicle more than
necessary.
Remove the cap
.
Never use blocks on or under the jack.
.
Do not start or run the engine while
vehicle is on the jack, as it may cause the
vehicle to move. This is especially true
for vehicles with limited slip differentials.
.
Do not allow passengers to stay in the
vehicle while it is on the jack.
SCE0702
Spare tire (if so equipped)
Getting the spare tire (if so
equipped)CV37D1-AB7BE0E7-F938-449F-AD80-100312B4783F
and tools
Raise the trunk floor cover
JVE0345X
Jacking tools
6-6
1 .
*
2 holding the spare tire.
*
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(339,1)
Carefully read the caution label attached
to the jack body and the following instructions.
JVE0346X
Jack-up point
1. Place the jack directly under the jack-up
point as illustrated so the top of the
jack contacts the vehicle at the jack-up
point. Align the jack head between the
two notches in the front or the rear as
shown. Also fit the groove of the jack
head between the notches as shown.
The jack should be used on level firm
ground.
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(340,1)
SCE0504
SCE0661
2. Loosen each wheel nut one or two turns
by turning counterclockwise with the
wheel nut wrench. Do not remove the
wheel nuts until the tire is off the
ground.
Installing CV37D1-93A81664-5ADD-41C9-883F-F248D6F75255
the spare tire
3. Carefully raise the vehicle until the tire
clears the ground. To lift the vehicle,
securely hold the jack lever and rod
with both hands as shown above.
Remove the wheel nuts, and then
remove the tire.
1. Clean any mud or dirt from the surface
between the wheel and hub.
The T-type spare tire (if so equipped) is
designed for emergency use. (See specific
instructions under the heading “Wheels
and tires” (P.8-33).)
2. Carefully put the spare tire on and
tighten the wheel nuts finger tight.
Models equipped with different sized
tires in the front and rear:
When replacing a front tire, make sure
that the hole in the spare tire wheel is
aligned with the pin on the brake rotor.
6-8
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(341,1)
3. With the wheel nut wrench, tighten
wheel nuts alternately and evenly in the
1 , *
2 , *
3 , *
4 ,
sequence illustrated (*
5 ) until they are tight.
*
.
4. Lower the vehicle slowly until the tire
touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle completely.
.
WARNING
.
Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to
become loose or come off. This could
cause an accident.
.
Do not use oil or grease on the wheel
studs or nuts. This could cause the nuts
to become loose.
.
Retighten the wheel nuts when the
vehicle has been driven for 600 miles
(1,000 km) (also in cases of a flat tire,
etc.).
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
80 ft-lb (108 N·m)
The wheel nuts must be kept tightened to specification at all times. It
is recommended that wheel nuts be
tightened to specifications at each
lubrication interval.
Adjust tire pressure to the COLD
pressure.
COLD pressure:
WARNING
.
Always make sure that the spare tire (if
so equipped) and jacking equipment are
properly secured after use. Such items
can become dangerous projectiles in an
accident or sudden stop.
.
The T-type spare tire and small size
spare tire (if so equipped) are designed
for emergency use. See specific instructions under the heading “Wheels and
tires” (P.8-33).
After the vehicle has been parked for
three hours or more or driven less
than 1 mile (1.6 km).
COLD tire pressures are shown on
the Tire and Loading Information
label affixed to the driver side center
pillar.
5. Securely store the flat tire and jacking
equipment in the vehicle.
6. Place the spare tire cover (if so
equipped) and the trunk floor carpeting
over the damaged tire.
7. Close the trunk.
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(342,1)
JUMP STARTING
CV37D1-781C1C30-AAC3-4DAF-8D44-D7D3051FE996
To start your engine with a booster battery,
the instructions and precautions below
must be followed.
.
Whenever working on or near a battery,
always wear suitable eye protectors (for
example, goggles or industrial safety
spectacles) and remove rings, metal
bands, or any other jewelry. Do not lean
over the battery when jump starting.
.
Do not attempt to jump start a frozen
battery. It could explode and cause
serious injury.
WARNING
.
If done incorrectly, jump starting can
lead to a battery explosion, resulting in
severe injury or death. It could also
damage your vehicle.
.
Explosive hydrogen gas is always present in the vicinity of the battery. Keep
all sparks and flames away from the
battery.
.
Do not allow battery fluid to come into
contact with eyes, skin, clothing or
painted surfaces. Battery fluid is a
corrosive sulphuric acid solution which
can cause severe burns. If the fluid
should come into contact with anything,
immediately flush the contacted area
with water.
.
Keep the battery out of the reach of
children.
.
The booster battery must be rated at 12
volts. Use of an improperly rated battery
can damage your vehicle.
.
Your vehicle has an automatic engine
cooling fan. It could come on at any time.
Keep hands and other objects away from
it.
life performance. Using the non-special
battery could cause early deterioration
of the battery and/or malfunction of the
Idling Stop System. For the special
battery, it is recommended to use
Genuine NISSAN parts. For more information, contact an INFINITI retailer.
.
It may take some time until the Idling
Stop System activates when the battery
is replaced or the battery terminal is
disconnected for extended periods and
then reconnected.
For 2.0L turbo gasoline engine models:
The vehicle has 2 batteries, a main battery
and an auxiliary battery. The engine cannot
be started if either battery is discharged.
First, apply the following procedure to the
main battery to jump-start the engine.
If the engine does not start, apply the
procedure to the auxiliary battery. For the
position of the batteries, see “Engine
compartment check locations” (P.8-4) or
“Battery” (P.8-17).
.
Use the special battery that is dedicated
for the Idling Stop System, with enhanced charge-discharge capacity and
6-10 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(343,1)
JVE0282X
VR30DDTT engine
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(344,1)
B to bring the batteries into
and *
close proximity to each other.
A
*
CAUTION
.
Do not allow the two vehicles to touch.
2. Apply parking brake. Move the shift
lever to the P (Park) position. Switch off
all unnecessary electrical systems
(light, heater, air conditioner, etc.).
3. Remove vent caps on the battery (if so
equipped). Cover the battery with a
C
firmly wrung out moist cloth *
to
reduce explosion hazard.
JVE0184X
2.0L turbo gasoline engine
MAIN BATTERY
(for all models)
CV37D1-A6D385ED-5B32-44A8-9B45-DF2E8A92870D
WARNING
Always follow the instructions below. Failure to do so could result in damage to the
charging system and cause personal injury.
1. If the booster battery is in another
A , position the two vehicles
vehicle *
6-12 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(345,1)
6. Start the engine of the booster vehicle
A and let it run for a few minutes.
*
7. Keep the engine speed of the booster
A at about 2,000 rpm, and
vehicle *
start the engine of the vehicle being
B .
jump started *
CAUTION
JVE0194X
2.0L turbo gasoline engine
4. For 2.0L turbo gasoline engine model:
Pull up the engine cover and remove it.
5. Connect jumper cables in the sequence
1 ? *
2 ? *
3 ? *
4 ).
as illustrated (*
CAUTION
.
.
Always connect positive (+) to positive
(+) and negative (−) to body ground (as
illustrated) − not to the battery.
Make sure the jumper cables do not
touch moving parts in the engine compartment and that clamps do not contact
any other metal.
NOTE:
For 2.0L turbo gasoline engine models, if
the engine cannot be started after the
procedure above, the auxiliary battery may
be discharged. Connect the jumper cables
to the auxiliary battery and apply the
procedure shown in “Auxiliary battery (for
2.0L turbo gasoline engine models)” (P.614).
Do not keep the starter motor engaged for
more than 10 seconds. If the engine does
not start right away, push the ignition
switch to the OFF position and wait 10
seconds before trying again.
8. After starting your engine, carefully
disconnect the negative cable and then
4 ? *
3 ? *
2 ?
the positive cable (*
1 ).
*
9. Replace the vent caps (if so equipped).
Be sure to dispose of the cloth used to
cover the vent holes as it may be
contaminated with corrosive acid.
10. Put the battery cover and the engine
cover back to the original location.
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(346,1)
JVE0142X
2.0L turbo gasoline engine
3. Move the shift lever to the P (Park)
AUXILIARY BATTERY (for 2.0L turbo
position.
gasoline engine models)
CV37D1-EB0EF723-AA10-44F8-B98D-BDFC44F2F7C6
1. If the booster battery is in another
A , position the two vehicles
vehicle *
A and *
B to bring the batteries into
*
close proximity to each other.
4. Switch off all unnecessary electrical
systems (headlights, heater, air conditioner, etc.).
5. Place the ignition switch in the OFF
position.
CAUTION
.
Do not allow the two vehicles to touch.
2. Apply the parking brake.
6-14 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(347,1)
CAUTION
Never keep the starter motor engaged for
more than 10 seconds. If the engine does
not start right away, place the ignition
switch in the OFF position and wait at least
10 seconds before trying again.
JVE0339X
6. Open the trunk.
7. Remove the clips
the trunk trim.
C *
D , then remove
*
8. Remove the vent caps, if so equipped,
on the battery.
9. Connect the jumper cables in the
1 , *
2 , *
3 ,
sequence as illustrated (*
4 ).
*
CAUTION
.
Always connect positive + to positive +
and negative 7 to body ground, NOT to
the battery’s negative 7.
.
.
Be sure that the jumper cables do not
touch moving parts in the engine compartment.
Be sure that the jumper cable’s clamps
do not contact any other metal.
10. Start the engine of the booster vehicle
A and let it run for a few minutes.
*
11. Depress the accelerator pedal of the
A at about 2,000 rpm.
booster vehicle *
12. Start the engine of the jumped vehicle
B in the normal manner.
*
13. After the engine is started, carefully
disconnect the jumper cables in the
opposite sequence from that illustrated
4 , *
3 , *
2 , *
1 ).
(*
14. Replace the vent caps, if removed.
15. Replace the trunk trim.
NOTE:
. If the engine cannot be started after the
procedure above, both the main and
the auxiliary batteries may be discharged. Jump-start the vehicle by
connecting one set of the jumper
cables to the main battery and another
set of the jumper cables to the auxiliary
battery at the same time, using the
procedure for jump-starting each battery.
. If the engine cannot be started, even
when the main and the auxiliary
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(348,1)
PUSH STARTING
IF YOUR VEHICLE OVERHEATS
CV37D1-5E7499C6-92EE-4262-B9B9-83F939236178
batteries are jump-started at the same
time, it is recommended you contact an
INFINITI retailer.
CV37D1-9ECDEC9C-D91E-43BE-8956-65EFDD4A98EF
Do not attempt to start the engine by
pushing.
CAUTION
.
Automatic Transmission (AT) models
cannot be push-started or tow-started.
Attempting to do so may cause transmission damage.
.
Three-way catalyst equipped models
should not be started by pushing since
the three-way catalyst may be damaged.
.
Never try to start the vehicle by towing
it; when the engine starts, the forward
surge could cause the vehicle to collide
with the tow vehicle.
CAUTION
.
Do not continue to drive if your vehicle
overheats. Doing so could cause engine
damage or a vehicle fire.
.
To avoid the danger of being scalded,
never remove the radiator cap while the
engine is still hot. When the radiator cap
is removed, pressurized hot water will
spurt out, possibly causing serious
injury.
.
Do not open the hood if steam is coming
out.
If your vehicle is overheating (indicated by
an extremely high temperature gauge
reading), or if you feel a lack of engine
power, detect abnormal noise, etc., take
the following steps:
1. Move the vehicle safely off the road,
apply the parking brake and move the
shift lever to the P (Park) position.
Do not stop the engine.
2. Turn off the climate control. Open all
the windows, move the heater or air
conditioner temperature control to
maximum hot and fan control to high
6-16 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(349,1)
TOWING YOUR VEHICLE
CV37D1-7FD19792-7E5A-41B4-A8FD-4D1A4B9EB1E8
speed.
3. If engine overheating is caused by
climbing a long hill on a hot day, run
the engine at a fast idle (approximately
1,500 rpm) until the temperature gauge
indication returns to normal.
4. Get out of the vehicle. Look and listen
for steam or coolant escaping from the
radiator before opening the hood. (If
steam or coolant is escaping, turn off
the engine.) Do not open the hood
further until no steam or coolant can be
seen.
5. Open the engine hood.
WARNING
WARNING
Be careful not to allow your hands, hair,
jewelry or clothing to come into contact
with, or get caught in, engine belts or the
engine cooling fan. The engine cooling fan
can start at any time.
7. After the engine cools down, check the
coolant level in the reservoir tank with
the engine running. Add coolant to the
reservoir tank if necessary. Have your
vehicle repaired. It is recommended
you visit an INFINITI retailer for this
service.
If steam or water is coming from the engine,
stand clear to prevent getting burned.
6. Visually check drive belts for damage or
looseness. Also check if the cooling fan
is running. The radiator hoses and
radiator should not leak water. If coolant is leaking or the cooling fan does
not run, stop the engine.
When towing your vehicle, all State (Provincial in Canada) and local regulations for
towing must be followed. Incorrect towing
equipment could damage your vehicle.
Towing instructions are available from an
INFINITI retailer. Local service operators are
familiar with the applicable laws and
procedures for towing. To assure proper
towing and to prevent accidental damage
to your vehicle, INFINITI recommends that
you have a service operator tow your
vehicle. It is advisable to have the service
operator carefully read the following precautions.
WARNING
.
Never ride in a vehicle that is being
towed.
.
Never get under your vehicle after it has
been lifted by a tow truck.
CAUTION
.
When towing, make sure that the transmission, axles, steering system and
powertrain are in working condition. If
any unit is damaged, dollies must be
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(350,1)
used.
.
Always attach safety chains before towing.
For information about towing your vehicle
behind a recreational vehicle (RV), see
“Flat towing” (P.10-19) of this manual.
SCE0967
Two-Wheel Drive (2WD) models
TOWING RECOMMENDED BY
INFINITI CV37D1-23FDC964-71B4-4D54-A9E0-DE67373C2DF7
backward), as this may cause serious
and expensive damage to the transmission. If it is necessary to tow the vehicle
with the front wheels raised, always use
towing dollies under the rear wheels.
Two-WheelCV37D1-9E0EF578-3514-4B10-979D-D236953F941A
Drive (2WD) models
INFINITI recommends that your vehicle be
towed with the driving (rear) wheels off the
ground or place the vehicle on a flat bed
truck as illustrated.
CAUTION
.
Never tow automatic transmission models with the rear wheels on the ground or
four wheels on the ground (forward or
.
When towing rear wheel drive models
with the front wheels on the ground or
on towing dollies: Place the ignition
switch in the ACC or ON position, and
secure the steering wheel in a straightahead position with a rope or similar
device.
6-18 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(351,1)
VEHICLE RECOVERY (freeing a stuck
vehicle) CV37D1-59A30A56-ED09-42A6-BC18-EAAD249D68F3
WARNING
To avoid vehicle damage, serious personal
injury or death when recovering a stuck
vehicle:
JVE0348X
All-Wheel Drive (AWD) models
Intelligent All-Wheel Drive (AWD)
models CV37D1-928888E2-FAEA-4E7E-AE79-B757A84827C9
INFINITI recommends that towing dollies be
used when towing your vehicle or the
vehicle be placed on a flat bed truck as
illustrated.
CAUTION
Never tow Intelligent AWD models with any
of the wheels on the ground as this may
cause serious and expensive damage to the
powertrain.
.
Contact a professional towing service to
recover the vehicle if you have any
questions regarding the recovery procedure.
.
Tow chains or cables must be attached
only to main structural members of the
vehicle.
.
Do not use the vehicle tie-downs to tow
or free a stuck vehicle.
.
Only use devices specifically designed
for vehicle recovery and follow the
manufacturer’s instructions.
.
Always pull the recovery device straight
out from the front of the vehicle. Never
pull at an angle.
.
Route recovery devices so they do not
touch any part of the vehicle except the
attachment point.
In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
6-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(352,1)
If your vehicle is stuck in sand, snow, mud,
etc., use a tow strap or other device
designed specifically for vehicle recovery.
Always follow the manufacturer’s instructions for the recovery device.
service to remove the vehicle.
Rocking aCV37D1-F72ACA55-5696-41CC-8BC5-2F62ECE3C3B9
stuck vehicle
If your vehicle is stuck in sand, snow, mud,
etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control
(VDC) system.
2. Make sure the area in front and behind
the vehicle is clear of obstructions.
3. Turn the steering wheel right and left to
clear an area around the front tires.
4. Slowly rock the vehicle forward and
backward.
. Shift back and forth between R
(Reverse) and D (Drive).
. Apply the accelerator as little as
possible to maintain the rocking
motion.
. Release the accelerator pedal before
shifting between R and D.
. Do not spin the tires above 35 MPH
(55 km/h).
5. If the vehicle cannot be freed after a few
tries, contact a professional towing
6-20 In case of emergency
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(353,1)
7 Appearance and care
Cleaning exterior ................................................
...
Washing .........................................................
...
Waxing ...........................................................
...
Removing spots ..............................................
...
Underbody .....................................................
...
Glass ..............................................................
...
Wheels ...........................................................
...
Chrome parts .................................................
...
Tire dressing ..................................................
...
Condition:
7-2
7-2
7-2
7-3
7-3
7-3
7-3
7-4
7-4
Cleaning interior ................................................
...
Leather cleaning kit (if so equipped) .............
...
Air fresheners ...............................................
...
Floor mats ....................................................
...
Seat belts .....................................................
...
Corrosion protection ...........................................
...
Most common factors contributing to
vehicle corrosion ..........................................
...
Environmental factors influence the rate
of corrosion ..................................................
...
To protect your vehicle from corrosion ..........
...
[ Edit: 2016/ 4/ 27
7-5
7-5
7-6
7-6
7-7
7-8
7-8
7-8
7-8
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(354,1)
CLEANING EXTERIOR
CV37D1-61244B6B-856E-4C02-A149-32D53D2458C8
In order to maintain the appearance of your
vehicle, it is important to take proper care
of it.
To protect the paint surface, wash your
vehicle as soon as you can:
. after a rainfall to prevent possible
damage from acid rain
. after driving on coastal roads
. when contaminants such as soot, bird
droppings, tree sap, metal particles or
bugs get on the paint surface
. when dust or mud builds up on the
surface
Whenever possible, store or park your
vehicle inside a garage or in a covered
area.
WASHINGCV37D1-89C768C5-665E-4332-B537-059AF9E0DABC
Wash dirt off the vehicle with a wet sponge
and plenty of water. Clean the vehicle
thoroughly using a mild soap, a special
vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm
(never hot) water.
CAUTION
.
When it is necessary to park outside, park
in a shady area or protect the vehicle with a
body cover.
Be careful not to scratch the paint surface
when putting on or removing the body
cover.
Do not use car washes that use acid in
the detergent. Some car washes, especially brushless ones, use some acid for
cleaning. The acid may react with some
plastic vehicle components, causing
them to crack. This could affect their
appearance, and also could cause them
not to function properly. Always check
with your car wash to confirm that acid is
not used.
.
Do not wash the vehicle with strong
household soap, strong chemical detergents, gasoline or solvents.
.
Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as
the surface may become water-spotted.
.
Avoid using tight-napped or rough
cloths, such as washing mitts. Care must
be taken when removing caked-on dirt or
other foreign substances so the paint
surface is not scratched or damaged.
Rinse the vehicle again with plenty of clean
water.
Inside flanges, seams and folds on the
doors, hatches and hood are particularly
vulnerable to the effects of road salt.
Therefore, these areas must be regularly
cleaned. Make sure that the drain holes in
the lower edge of the door are open. Spray
water under the body and in the wheel
wells to loosen the dirt and wash away
road salt.
Avoid leaving water spots on the paint
surface by using a damp chamois to dry the
vehicle.
WAXING
CV37D1-FDECF156-7849-4E3B-9508-4112D8244F1D
Regular waxing protects the paint surface
and helps retain new vehicle appearance.
Polishing is recommended to remove builtup wax residue and to avoid a weathered
appearance before reapplying wax.
An INFINITI retailer can assist you in
choosing the proper product.
. Wax your vehicle only after a thorough
7-2 Appearance and care
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(355,1)
washing. Follow the instructions supplied with the wax.
. Do not use a wax containing any
abrasives, cutting compounds or cleaners that may damage the vehicle
finish.
Machine compound or aggressive polishing on a base coat/clear coat paint finish
may dull the finish or leave swirl marks.
REMOVING
SPOTS
CV37D1-E8B74468-BCE5-4709-9D00-2285EB5AF58E
Remove tar and oil spots, industrial dust,
insects, and tree sap as quickly as possible
from the paint surface to avoid lasting
damage or staining. Special cleaning
products are available at an INFINITI
retailer or any automotive accessory
stores.
UNDERBODY
CV37D1-7716E8ED-9E43-4D83-A6F6-497E61851D28
In areas where road salt is used in winter,
the underbody must be cleaned regularly.
This will prevent dirt and salt from building
up and causing the acceleration of corrosion on the underbody and suspension.
Before the winter period and again in the
spring, the underseal must be checked
and, if necessary, re-treated.
GLASS
CV37D1-08906C72-395B-4C0D-AB51-77874E33DDFB
Use glass cleaner to remove smoke and
dust film from the glass surfaces. It is
normal for glass to become coated with a
film after the vehicle is parked in the hot
sun. Glass cleaner and a soft cloth will
easily remove this film.
CAUTION
Do not use abrasive cleaners when washing
the wheels.
CAUTION
When cleaning the inside of the windows,
do not use sharp-edged tools, abrasive
cleaners or chlorine-based disinfectant cleaners. They could damage the electrical
conductors, radio antenna elements or rear
window defroster elements.
WHEELS
. INFINITI recommends that the road
wheels be waxed to protect against
road salt in areas where it is used
during winter.
AluminumCV37D1-FBDB2630-0B4E-48F5-A670-4D29933E3E16
alloy wheels
Wash regularly with a sponge dampened in
a mild soap solution, especially during
winter months in areas where road salt is
used. Salt could discolor the wheels if not
removed.
CAUTION
CV37D1-86BF7C1F-D7AC-4955-A781-342F1840AEDE
Wash the wheels when washing the vehicle
to maintain their appearance.
. Clean the inner side of the wheels when
the wheel is changed or the underside
of the vehicle is washed.
. Inspect wheel rims regularly for dents
or corrosion. Such damage may cause
loss of pressure or poor seal at the tire
bead.
Follow the directions below to avoid staining or discoloring the wheels:
.
Do not use a cleaner that uses strong
acid or alkali contents to clean the
wheels.
.
Do not apply wheel cleaners to the
wheels when they are hot. The wheel
temperature should be the same as
Appearance and care
Condition:
[ Edit: 2016/ 4/ 27
7-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(356,1)
.
ambient temperature.
.
Rinse the wheel to completely remove
the cleaner within 15 minutes after the
cleaner is applied.
Do not use an automatic car wash if the
vehicle is equipped with bright wheels.
The wheel coating may be damaged.
.
Do not use a brush to wash the wheels if
the vehicle is equipped with bright
wheels. The wheel coating may be
damaged.
Bright wheels
(if so equipped)
CV37D1-E38C4D82-71F0-4B32-8780-FF0F5F663A35
The bright wheels use a different coating
process than typical aluminum alloy wheel
and they are not plated wheels. These
wheels are clear-coated and require the
following special cleaning. They should be
regularly washed with a soft sponge
soaked in a lot of water. After washing
with water, wipe clean with a dry, soft cloth
and dry completely. When there is chemical
or tire wax, or dirt such as an antifreeze
agent on the surface, wash them with
water as soon as possible.
CAUTION
.
7-4
The surfaces of the wheels use a
different coating process than typical
aluminum alloy wheels. Do not use
aluminum alloy wheel cleaners or abrasive cleaners to clean the wheels. Using
such cleaners could damage the wheel
surfaces.
CHROME PARTS
CV37D1-0094087B-0A17-4FF2-9C41-F31A14D3D6BC
Clean chrome parts regularly with a nonabrasive chrome polish to maintain the
finish.
. Apply a light coat of tire dressing to
help prevent it from entering the tire
tread/grooves (where it would be difficult to remove).
. Wipe off excess tire dressing using a dry
towel. Make sure the tire dressing is
completely removed from the tire
tread/grooves.
. Allow the tire dressing to dry as
recommended by tire dressing manufacturer.
TIRE DRESSING
CV37D1-049714D9-BD47-419F-9036-9C9F29D765E3
INFINITI does not recommend the use of
tire dressings. Tire manufacturers apply a
coating to the tires to help reduce discoloration of the rubber. If a tire dressing is
applied to the tires, it may react with the
coating and form a compound. This compound may come off the tire while driving
and stain the vehicle paint.
If you choose to use a tire dressing, take
the following precautions:
. Use a water-based tire dressing. The
coating on the tire dissolves more
easily with an oil-based tire dressing.
Appearance and care
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(357,1)
CLEANING INTERIOR
CV37D1-5EAC8407-7781-4E05-920D-B9F833E99438
Occasionally remove loose dust from the
interior trim, plastic parts and seats using
a vacuum cleaner or soft bristled brush.
Wipe the vinyl and leather surfaces with a
clean, soft cloth dampened in mild soap
solution, then wipe clean with a dry soft
cloth.
LEATHER CLEANING KIT (if so
equipped) GUID-296B362A-1F90-4457-8C40-5656EA1BE38C
CAUTION
.
Never use benzine, thinner, or any
similar material.
.
For cleaning, use a soft cloth, dampened
with water. Never use a rough cloth,
alcohol, benzine, thinner or any kind of
solvent or paper towel with a chemical
cleaning agent. They will scratch or
cause discoloration to the lens.
Regular care and cleaning is required in
order to maintain the appearance of the
leather.
Before using any fabric protector, read the
manufacturer’s recommendations. Some
fabric protectors contain chemicals that
may stain or bleach the seat material.
.
Use a cloth dampened only with water, to
clean the meter and gauge lens.
Do not spray any liquid such as water on
the meter lens. Spraying liquid may
cause the system to malfunction.
.
Small dirt particles can be abrasive and
damaging to the leather surfaces and
should be removed promptly. Do not use
saddle soap, car waxes, polishes, oils,
cleaning fluids, solvents, detergents or
ammonia-based cleaners as they may
damage the leather’s natural finish.
WARNING
Do not use water or acidic cleaners (hot
steam cleaners) on the seat. This can
damage the seat or occupant classification
sensors. This can also affect the operation of
the air bag system and result in serious
personal injury.
.
Only use fabric protectors approved by
INFINITI.
.
Do not use glass or plastic cleaner on
meter or gauge lens covers. It may
damage the lens cover.
Spray onto the leather cleaning cloth, then
gently wipe the surface of leather. Use a
dry towel to absorb any excess moisture.
Clean light-colored leather more frequently
because soiling on such surfaces is much
more visible.
Always follow the manufacturer’s instructions supplied with the leather cleaning
kit.
You can obtain the leather cleaning kit from
an INFINITI retailer or other authorized
repair shop.
CAUTION
Do not leave the leather cleaning kit inside
the vehicle. The leather cleaning kit left in a
closed vehicle can become very hot.
Appearance and care
Condition:
[ Edit: 2016/ 4/ 27
7-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(358,1)
AIR FRESHENERS
CV37D1-6145786E-8E5A-423A-A3C5-028C5AD788FF
backwards.
Most air fresheners use a solvent that
could affect the vehicle interior. If you use
an air freshener, take the following precautions:
.
Use only genuine INFINITI floor mats or
equivalent floor mats that are specifically designed for use in your vehicle
model and model year.
. Hanging-type air fresheners can cause
permanent discoloration when they
contact vehicle interior surfaces. Place
the air freshener in a location that
allows it to hang free and not contact
an interior surface.
. Liquid-type air fresheners typically clip
on the vents. These products can cause
immediate damage and discoloration
when spilled on interior surfaces.
Carefully read and follow the manufacturer’s instructions before using air fresheners.
.
Properly position the mats in the floorwell using the floor mat positioning
hook. See “Floor mat installation” (P.76).
.
Make sure the floor mat does not
interfere with pedal operation.
.
Periodically check the floor mats to make
sure they are properly installed.
.
After cleaning the vehicle interior, check
the floor mats to make sure they are
properly installed.
FLOOR MATS
CV37D1-7EBEC747-2285-4A16-B3E7-D47C43B29BF3
WARNING
To avoid potential pedal interference that
may result in a collision, injury or death:
.
7-6
The use of genuine INFINITI floor mats can
extend the life of your vehicle carpet and
make it easier to clean the interior. Mats
should be maintained with regular cleaning and replaced if they become excessively worn.
JVA0023X
Floor matCV37D1-D9CDBE08-03DE-4459-9F04-93DA3AC654D3
installation
Your vehicle is equipped with floor mat
positioning hook(s). The number and
shape of the floor mat positioning hook(s)
for each seating position varies depending
on the vehicle.
When installing genuine INFINITI floor
mats, follow the installation instructions
provided with the floor mat and the
following:
1. Position the floor mat in the floorwell so
that the mat grommet holes are aligned
with the hook(s).
NEVER place a floor mat on top of
another floor mat in the driver front
position or install them upside down or
Appearance and care
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(359,1)
2. Secure the grommet holes into the
hook(s) and ensure that the floor mat
is properly positioned.
3. Make sure the floor mat does not
interfere with pedal operation. With
the ignition in the OFF position and
the shift lever in the P (Park) position,
fully apply and release all pedals. The
floor mat must not interfere with pedal
operation or prevent the pedal from
returning to its normal position. It is
recommended you see an INFINITI
retailer for details about installing the
floor mats in your vehicle.
cal solvents to clean the seat belts, since
these materials may severely weaken the
seat belt webbing.
SAI0051
Positioning hooks
The illustration shows the location of the
floor mat positioning hooks.
SEAT BELTS
CV37D1-2D317E9D-E485-4E01-BEF8-63AE0061A86C
The seat belts can be cleaned by wiping
them with a sponge dampened in a mild
soap solution. Allow the belts to dry
completely before using them.
See “Seat belts” (P.1-11).
WARNING
Do not allow wet seat belts to roll up in the
retractor. NEVER use bleach, dye, or chemiAppearance and care
Condition:
[ Edit: 2016/ 4/ 27
7-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(360,1)
CORROSION PROTECTION
CV37D1-7C9F6819-C67C-4001-ADB4-4331407552AC
MOST COMMON FACTORS CONTRIBUTING TO
VEHICLE CORROSION
CV37D1-E979CBFD-D47E-46D2-AB44-0988347AF315
. The accumulation of moisture-retaining
dirt and debris in body panel sections,
cavities, and other areas.
. Damage to paint and other protective
coatings caused by gravel and stone
chips or minor traffic accidents.
ENVIRONMENTAL FACTORS INFLUENCE THECV37D1-C2F6F55B-7D15-4DC8-A7A4-CB5B62B9E8C9
RATE OF CORROSION
Moisture
CV37D1-12E981E2-C1A4-4D98-9FBC-150933E5F21D
Accumulation of sand, dirt and water on
the vehicle body underside can accelerate
corrosion. Wet floor coverings will not dry
completely inside the vehicle, and should
be removed for drying to avoid floor panel
corrosion.
Relative humidity
CV37D1-64711E0F-757E-409A-B8A7-2864F3659D0F
Corrosion will be accelerated in areas of
high relative humidity, especially those
areas where the temperatures stay above
freezing where atmospheric pollution exists, or where road salt is used.
7-8
Temperature
CV37D1-EA28CD9A-484D-45B8-B7CF-AC2A62B65F06
A temperature increase will accelerate the
rate of corrosion to those parts which are
not well ventilated.
CAUTION
.
NEVER remove dirt, sand or other debris
from the passenger compartment by
washing it out with a hose. Remove dirt
with a vacuum cleaner.
.
Never allow water or other liquids to
come in contact with electronic components inside the vehicle as this may
damage them.
Air pollution
CV37D1-CB81F8AB-C2B9-4F0F-BD74-30B3EB1BA3D5
Industrial pollution, the presence of salt in
the air in coastal areas, or heavy road salt
use will accelerate the corrosion process.
Road salt will also accelerate the disintegration of paint surfaces.
TO PROTECT YOUR VEHICLE FROM
CORROSION
CV37D1-88825C6B-922A-4901-8950-E810E911CD7E
. Wash and wax your vehicle often to
keep the vehicle clean.
. Always check for minor damage to the
paint and repair it as soon as possible.
. Keep drain holes at the bottom of the
doors open to avoid water accumulation.
. Check the underbody for accumulation
of sand, dirt or salt. If present, wash
with water as soon as possible.
Chemicals used for road surface deicing
are extremely corrosive. They accelerate
corrosion and deterioration of underbody
components such as the exhaust system,
fuel and brake lines, brake cables, floor
pan and fenders.
In winter, the underbody must be cleaned
periodically.
For additional protection against rust and
corrosion, which may be required in some
areas, it is recommended you consult an
INFINITI retailer.
Appearance and care
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(361,1)
8 Do-it-yourself
Maintenance precautions ....................................
...
8-3
Engine compartment check locations ..................
...
8-4
VR30DDTT engine ...........................................
...
8-4
2.0L turbo gasoline engine .............................
...
8-5
Engine cooling system (for VR30DDTT
engine models) ...................................................
...
8-6
Checking engine coolant level .......................
...
8-7
Changing engine coolant ................................
...
8-7
Engine cooling system (for 2.0L turbo gasoline
engine models) ...................................................
...
8-8
Checking engine coolant level ........................
...
8-8
Changing engine coolant ................................
...
8-9
Intercooler cooling system (for VR30DDTT
engine models) ...................................................
...
8-9
Checking intercooler coolant level ................
...
8-10
Changing intercooler coolant ........................
...
8-10
Engine oil .........................................................
...
8-10
Checking engine oil level ..............................
...
8-11
Changing engine oil and filter .......................
...
8-11
Automatic Transmission Fluid (ATF) ...................
...
8-14
Power steering fluid (models with hydraulic
pump electric power steering) ...........................
...
8-14
Brake fluid ........................................................
...
8-15
Window washer fluid ........................................
...
8-16
Condition:
Battery .............................................................
...
Main battery location ..................................
...
Auxiliary battery location
(for 2.0L turbo gasoline engine models) ......
...
Checking battery fluid level .........................
...
Jump starting ..............................................
...
Variable voltage control system ........................
...
Drive belts .......................................................
...
Spark plugs .....................................................
...
Replacing spark plugs .................................
...
Air cleaner .......................................................
...
Windshield wiper blades ..................................
...
Cleaning .....................................................
...
Replacing ....................................................
...
Brakes .............................................................
...
Self-adjusting brakes ..................................
...
Brake pad wear warning .............................
...
Fuses ...............................................................
...
Engine compartment ...................................
...
Passenger compartment ..............................
...
Intelligent Key battery replacement ..................
...
Lights ...............................................................
...
Headlights ..................................................
...
Exterior and interior lights ..........................
...
[ Edit: 2016/ 4/ 27
8-17
8-18
8-18
8-19
8-20
8-20
8-20
8-21
8-22
8-22
8-23
8-23
8-23
8-24
8-24
8-24
8-25
8-25
8-27
8-28
8-30
8-31
8-31
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(362,1)
Wheels and tires ...............................................
...
8-33
Tire pressure ................................................
...
8-33
Tire labeling .................................................
...
8-37
Condition:
Types of tires ..............................................
...
8-39
Tire chains ..................................................
...
8-41
Changing wheels and tires ..........................
...
8-42
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(363,1)
MAINTENANCE PRECAUTIONS
CV37D1-239C92D7-82C6-4E8E-B4CA-4F36484B9DCB
When performing any inspection or maintenance work on your vehicle, always take
care to prevent serious accidental injury to
yourself or damage to the vehicle. The
following are general precautions which
should be closely observed.
WARNING
.
.
.
.
.
Park the vehicle on a level surface, apply
the parking brake securely and block the
wheels to prevent the vehicle from
moving. Move the shift lever to P (Park).
Be sure the ignition switch is in the OFF
or LOCK position when performing any
parts replacement or repairs.
Never connect or disconnect the battery
or any transistorized component while
the ignition switch is in the ON position.
.
It is advisable to secure or remove any
loose clothing and remove any jewelry,
such as rings, watches, etc. before
working on your vehicle.
.
Always wear eye protection whenever
you work on your vehicle.
.
If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to
escape.
.
Never get under the vehicle while it is
supported only by a jack. If it is
necessary to work under the vehicle,
support it with safety stands.
.
Keep smoking materials, flame and
sparks away from fuel tank and the
battery.
.
Never leave the engine or automatic
transmission related component harnesses disconnected while the ignition
switch is in the ON position.
If you must work with the engine
running, keep your hands, clothing, hair
and tools away from moving fans, belts
and any other moving parts.
.
Your vehicle is equipped with an automatic engine cooling fan. It may come on
at any time without warning, even if the
ignition key is in the OFF position and
the engine is not running. To avoid
injury, always disconnect the negative
battery cable before working near the
fan.
Because the fuel lines are under high
pressure even when the engine is off, it
is recommended you visit an INFINITI
retailer for service of the fuel filter or fuel
lines.
CAUTION
.
Do not work under the hood while the
engine is hot. Turn the engine off and
wait until it cools down.
.
Avoid direct contact with used engine oil
and coolant. Improperly disposed engine
oil, coolant, and/or other vehicle fluids
can damage the environment. Always
conform to local regulations for disposal
of vehicle fluid.
This “8. Do-it-yourself” section gives instructions regarding only those items
which are relatively easy for an owner to
perform.
A genuine INFINITI Service Manual is also
available. (See “Owner’s Manual/Service
Manual order information” (P.10-24).)
You should be aware that incomplete or
improper servicing may result in operating
difficulties or excessive emissions, and
could affect your warranty coverage. If in
doubt about any servicing, it is recomDo-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(364,1)
ENGINE COMPARTMENT CHECK LOCATIONS
CV37D1-40355A41-7F10-4734-AE5E-6CAA3DAE4D37
mended you have it done by an INFINITI
retailer.
JVC0968X
VR30DDTTCV37D1-39A98C09-D1A0-4AF5-94E8-85F92A109897
ENGINE
1.
2.
3.
4.
5.
8-4
Battery
Engine oil dipstick
Engine oil filler cap
Brake fluid reservoir
Fuse/fusible link holder
6.
7.
8.
9
10.
11.
Air cleaner
Engine drive belt location
Radiator filler cap
Intercooler cooling reservoir
Engine coolant reservoir
Window washer fluid reservoir
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(365,1)
*:
The auxiliary battery is located in the
trunk. (See “Auxiliary battery location
(for 2.0L turbo gasoline engine models)” (P.8-18).)
JVC0646X
2.0L TURBO
GASOLINE ENGINE
CV37D1-31629E6C-31F5-4793-AFB7-A9425E876202
1.
2.
3.
4.
5.
Fuse and fusible link holder
Main battery*
Engine oil filler cap
Brake fluid reservoir
Engine coolant reservoir
6.
7.
8.
9.
Fuse and fusible link holder
Engine oil dipstick
Engine drive belt location
Power steering fluid reservoir (if so
equipped)
10. Window washer fluid reservoir
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(366,1)
ENGINE COOLING SYSTEM (for VR30DDTT
engine models)
CV37D1-DDCBA326-33A3-4F9C-BEEC-D8D38B2C8973
The engine cooling system is filled at the
factory with a pre-diluted mixture of 50%
Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water to provide yearround anti-freeze and coolant protection.
The anti-freeze solution contains rust and
corrosion inhibitors. Additional engine
cooling system additives are not necessary.
clog the cooling system and cause
damage to the engine, transmission
and/or cooling system.
.
When adding or replacing coolant, be
sure to use only Genuine NISSAN Long
Life Antifreeze/Coolant (blue) or equivalent. Genuine NISSAN Long Life Antifreeze/Coolant (blue) is pre-diluted to
provide antifreeze protection to −348F
(−378C). If additional freeze protection is
needed due to weather where you
operate your vehicle, add Genuine
NISSAN Long Life Antifreeze/Coolant
(blue) concentrate following the directions on the container. If an equivalent
coolant other than Genuine NISSAN Long
Life Antifreeze/Coolant (blue) is used,
follow the coolant manufacture’s instructions to maintain minimum antifreeze
protection to −348F (−378C). The use of
other types of coolant solutions other
than Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent may
damage the engine cooling system.
.
The life expectancy of the factory-fill
coolant is 105,000 miles (168,000 km)
or 7 years. Mixing any other type of
coolant other than Genuine NISSAN Long
Life Antifreeze/Coolant (blue), including
WARNING
.
Never remove the radiator cap when the
engine is hot. Wait until the engine and
radiator cool down. Serious burns could
be caused by high pressure fluid escaping from the radiator. See precautions in
“If your vehicle overheats” (P.6-16) of
this manual.
.
The radiator is equipped with a pressure
type radiator cap. To prevent engine
damage, use only a genuine NISSAN
radiator cap.
CAUTION
.
8-6
Never use any cooling system additives
such as radiator sealer. Additives may
Genuine NISSAN Long Life Antifreeze/
Coolant (green), or the use of nondistilled water will reduce the life expectancy of the factory-fill coolant. Refer
to the “9. Maintenance and schedules”
section of this manual for more details.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(367,1)
engine. Run the engine until it reaches
normal operating temperature. Add coolant
1 . Tighten the cap
up to the MAX level *
securely after adding engine coolant.
If the cooling system requires coolant
frequently, have it checked. It is recommended you visit an INFINITI retailer for
this service.
CHANGING
ENGINE COOLANT
CV37D1-EB4AE632-FC33-46FA-B4E5-33D807075B2C
JVM0652X
CHECKINGCV37D1-9D05A2B4-5FF4-45F8-9AD8-787609A71844
ENGINE COOLANT LEVEL
Check the coolant level in the reservoir
tank when the engine is running and after
it reaches normal operating temperature. If
2 ,
the coolant level is below MIN level *
1 . If the
add coolant up to the MAX level *
reservoir tank is empty, check the coolant
level in the radiator when the engine is
cold. If there is insufficient coolant in the
radiator, fill the radiator with coolant up to
the filler cap above the radiator upper hose
opening and also add it to the reservoir
1 . Put on the
tank up to the MAX level *
filler cap above the radiator upper hose
and with the reservoir cap open, start the
.
Avoid direct skin contact with used
coolant. If skin contact is made, wash
thoroughly with soap or hand cleaner as
soon as possible.
.
Keep coolant out of reach of children and
pets.
Engine coolant must be disposed of
properly. Check your local regulations.
It is recommended that major cooling
system repairs be performed by an INFINITI
retailer. The service procedures can be
found in the appropriate INFINITI Service
Manual.
Improper servicing can result in reduced
heater performance and engine overheating.
WARNING
.
To avoid the danger of being scalded,
never change the coolant when the
engine is hot.
.
Never remove the radiator cap when the
engine is hot. Serious burns could be
caused by high pressure fluid escaping
from the radiator.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(368,1)
ENGINE COOLING SYSTEM (for 2.0L turbo
gasoline engine models)
CV37D1-5E9018BE-5361-4EA0-B72D-8E0E4641BB8D
The engine cooling system is filled at the
factory with a pre-diluted mixture of 50%
BASF Glysantin® G48® and 50% water to
provide year-round anti-freeze and coolant
protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are
not necessary.
pre-diluted to provide antifreeze protection to −348F (−378C). If additional freeze
protection is needed due to weather
where you operate your vehicle, add
BASF Glysantin® G48® concentrate following the directions on the container. If
an equivalent coolant other than BASF
Glysantin® G48® is used, follow the
coolant manufacture’s instructions to
maintain minimum antifreeze protection
to −348F (−378C). The use of other types
of coolant solutions other than BASF
Glysantin® G48® or equivalent may
damage the engine cooling system.
WARNING
Never remove the radiator cap when the
engine is hot. Wait until the engine and
radiator cool down. Serious burns could be
caused by high pressure fluid escaping from
the radiator. See precautions in “If your
vehicle overheats” (P.6-16) of this manual.
CAUTION
.
.
8-8
Never use any cooling system additives
such as radiator sealer. Additives may
clog the cooling system and cause
damage to the engine, transmission
and/or cooling system.
.
The life expectancy of the factory-fill
coolant is 120,000 miles (192,000 km)
or 10 years. Mixing any other type of
coolant other than BASF Glysantin®
G48®, or the use of non-distilled water
will reduce the life expectancy of the
factory-fill coolant. Refer to the “9.
Maintenance and schedules” section of
this manual for more details.
When adding or replacing coolant, be
sure to use only BASF Glysantin® G48®
or equivalent. BASF Glysantin® G48® is
JVM0303X
CHECKINGCV37D1-6724BF42-9F5F-4667-AF60-5CBD3339921E
ENGINE COOLANT LEVEL
Check the coolant level in the reservoir
when the engine is running and after it
reaches normal operating temperature. If
2 ,
the coolant level is below MIN level *
1 .
add coolant up to the MAX level *
Tighten the cap securely after adding
engine coolant.
If the cooling system frequently requires
coolant, have it checked. It is recommended you visit an INFINITI retailer for
this service.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(369,1)
INTERCOOLER COOLING SYSTEM (for
VR30DDTT engine models)
CV37D1-BEC2CD96-BE37-4CB7-B303-7ECB564D7DAF
CHANGING
ENGINE COOLANT
CV37D1-2A42009A-C30E-439B-9AEB-DBF5EB46D0C7
It is recommended that major cooling
system repairs be performed by an INFINITI
retailer. The service procedures can be
found in the appropriate INFINITI Service
Manual.
Improper servicing can result in reduced
heater performance and engine overheating.
The intercooler cooling system is filled at
the factory with a pre-diluted mixture of
50% Genuine NISSAN Long Life Antifreeze/
Coolant (blue) and 50% water to provide
year-round anti-freeze and coolant protection. The antifreeze solution contains rust
and corrosion inhibitors. Additional intercooler cooling system additives are not
necessary.
WARNING
WARNING
.
To avoid the danger of being scalded,
never change the coolant when the
engine is hot.
.
Never remove the radiator cap when the
engine is hot. Serious burns could be
caused by high pressure fluid escaping
from the radiator.
.
Avoid direct skin contact with used
coolant. If skin contact is made, wash
thoroughly with soap or hand cleaner as
soon as possible.
.
Keep coolant out of reach of children and
pets.
.
Never remove the coolant reservoir cap
when the engine is hot. Wait until the
engine cools down. Serious burns could
be caused by high pressure fluid escaping from the coolant reservoir.
.
The intercooler reservoir is equipped
with a pressure type cap. To prevent
engine and intercooler damage, use only
a genuine NISSAN intercooler reservoir
cap.
.
When adding or replacing coolant, be
sure to use only Genuine NISSAN Long
Life Antifreeze/Coolant (blue) or equivalent. Genuine NISSAN Long Life Antifreeze/Coolant (blue) is pre-diluted to
provide antifreeze protection to −348F
(−378C). If additional freeze protection is
needed due to weather where you
operate your vehicle, add Genuine
NISSAN Long Life Antifreeze/Coolant
(blue) concentrate following the directions on the container. If an equivalent
coolant other than Genuine NISSAN Long
Life Antifreeze/Coolant (blue) is used,
follow the coolant manufature’s instructions to maintain minimum antifreeze
protection to −348F (−378C). The use of
other types of coolant solutions other
than Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent may
damage the Intercooler cooling system.
CAUTION
.
Engine coolant must be disposed of
properly. Check your local regulations.
intercooler.
Never use any additives in the coolant
such as radiator sealer in the cooling
system. This may cause damage to the
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(370,1)
ENGINE OIL
CV37D1-A7C453B1-918A-4063-9B01-B06D637810DF
CHANGING
INTERCOOLER COOLANT
CV37D1-7B005827-CEF6-44B7-B2C9-2BC4B72D57FC
Intercooler coolant is maintenance-free.
If replacement is required, it is recommended you visit an INFINITI retailer for
this service.
Improper servicing can result in intercooler
overheating.
WARNING
.
JVM0653X
CHECKING INTERCOOLER COOLANT
LEVEL
CV37D1-5F0552C1-574B-4EE7-A4C1-9F60B17628D5
Check the coolant level in the reservoir
when the engine is cold. If the coolant level
2 , add coolant to
is below the MIN level *
1 .
the MAX level *
If the intercooler cooling system frequently
requires coolant, have it checked. It is
recommended you visit an INFINITI retailer
for this service.
To avoid the danger of being scalded,
never change the coolant when the
engine is hot.
.
Never remove the cap when the engine is
hot. Serious burns could be caused by
high pressure fluid escaping from the
intercooler cooling reservoir.
.
Avoid direct skin contact with used
coolant. If skin contact is made, wash
thoroughly with soap or hand cleaner as
soon as possible.
.
Keep coolant out of the reach of children
and pets.
Intercooler coolant must be disposed of
properly. Check your local regulations.
JVM0654X
VR30DDTT engine
JVM0429X
2.0L turbo gasoline engine
8-10 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(371,1)
CHECKINGCV37D1-F1375A53-9C95-4044-9249-810C01D32BB1
ENGINE OIL LEVEL
1. Park the vehicle on a level surface and
apply the parking brake.
2. Run the engine until it reaches operating temperature.
3. Turn off the engine. Wait more than 15
minutes for the oil to drain back into
the oil pan.
4. Remove the dipstick and wipe it clean.
Reinsert it all the way.
5. Remove the dipstick again and check
the oil level. It should be within the
1 . If the oil level is below *
2 ,
range *
remove the oil filler cap and pour
recommended oil through the opening.
3 .
Do not overfill *
6. Recheck oil level with the dipstick.
It is normal to add some oil between oil
maintenance intervals or during the breakin period, depending on the severity of
operating conditions.
CAUTION
such damage is not covered by warranty.
CAUTION
CHANGINGCV37D1-9647A2B0-4907-4EB7-83BB-101487A3007A
ENGINE OIL AND FILTER
Vehicle set-up
CV37D1-A77DD255-330F-4511-9453-9FE2A6353943
Make sure the correct lifting and support
points are used to avoid vehicle damage.
1. Park the vehicle on a level surface and
apply the parking brake.
2. Run the engine until it reaches operating temperature.
3. Turn the engine off and wait more than
15 minutes.
4. Raise and support the vehicle using a
suitable floor jack and safety jack
stands.
. Place the safety jack stands under
the vehicle jack-up points.
. A suitable adapter should be attached to the jack stand saddle.
5. For VR30DDTT engine models: Remove
the plastic engine undercover.
. Remove the small plastic clip at the
center point of the undercover.
. Then remove the other bolts that
hold the undercover in place.
Oil level should be checked regularly.
Operating the engine with an insufficient
amount of oil can damage the engine, and
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(372,1)
Engine oilCV37D1-E1C6F53B-E6EA-4EFF-A78E-74F5B4A219BD
and filter
1. Place a large drain pan under the drain
plug.
2. Remove the oil filler cap.
1
3. Remove the drain plug *
with a
wrench and completely drain the oil.
CAUTION
Be careful not to burn yourself, as the
engine oil is hot.
JVM0668X
VR30DDTT engine (2WD models)
JVM0667X
Waste oil must be disposed of
properly.
. Check your local regulations.
4. (Perform steps 4 to 7 only when the
engine oil filter change is needed.)
2.0L turbo gasoline engine
.
2 with an oil filter
Loosen the oil filter *
wrench. Remove the oil filter by turning
it by hand.
5. Wipe the engine oil filter mounting
surface with a clean rag.
CAUTION
JVM0669X
VR30DDTT engine (AWD models)
JVM0428X
2.0L turbo gasoline engine
Be sure to remove any old rubber gasket
remaining on the mounting surface of the
8-12 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(373,1)
engine. Failure to do so could lead to engine
damage.
6. Coat the gasket on the new filter with
clean engine oil.
7. For VR30DDTT engine models: Screw in
the oil filter clockwise until a slight
resistance is felt, then tighten additionally more than 2/3 turn.
For 2.0L turbo gasoline engine models:
Securely tighten the oil filter. Do not
use excessive force.
Oil filter tightening torque:
VR30DDTT engine models
11 to 15 ft-lb
(14.7 to 20.6 N·m)
2.0L turbo gasoline engine models
19 ft-lb
(25 N·m)
8. Clean and re-install the drain plug with
a new washer. Securely tighten the
drain plug with a wrench.
After the CV37D1-790CC92C-2688-443C-80B6-74DD163C016F
operation
2.0L turbo gasoline engine models
22 ft-lb
(30 N·m)
1. Install the engine undercover into
position as the following steps.
Do not use excessive force.
a. Pull the center of the small plastic
clip out.
9. Refill engine with recommended oil and
install the oil filler cap securely.
b. Hold the engine undercover into
position.
See “Capacities and recommended
fluids/lubricants” (P.10-2) for drain
and refill capacity. The drain and refill
capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use
the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage
around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than
15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
Drain plug tightening torque:
VR30DDTT engine models
22 to 29 ft-lb
(29.4 to 39.2 N·m)
c. Insert the clip through the undercover into the hole in the frame, then
push the center of the clip in to lock
the clip in place.
d. Install the other bolts that hold the
undercover in place. Be careful not
to strip the bolts or over-tighten
them.
2. Lower the vehicle carefully to the
ground.
3. Dispose of waste oil and filter properly.
WARNING
.
Prolonged and repeated contact with
used engine oil may cause skin cancer.
.
Try to avoid direct skin contact with used
oil. If skin contact is made, wash
thoroughly with soap or hand cleaner
as soon as possible.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(374,1)
AUTOMATIC TRANSMISSION FLUID (ATF)
CV37D1-9C4CC2F5-7026-4A93-9DEC-281F6C16BCFB
.
Keep used engine oil out of reach of
children.
POWER STEERING FLUID (models with
hydraulic pump electric power steering)
CV37D1-D45EC9E2-EB65-45B1-8BFF-8683725B7363
When checking or replacement is required,
we recommend an INFINITI retailer for
servicing.
CAUTION
.
It is recommended that you use only
Genuine NISSAN Matic S ATF. Do not mix
with other fluids.
.
Using automatic transmission fluid other
than Genuine NISSAN Matic S ATF may
cause deterioration in driveability and
automatic transmission durability, and
may damage the automatic transmission. Damage caused by the use of fluid
other than as recommended is not
covered by the INFINITI new vehicle
limited warranty.
JVM0332X
WARNING
Power steering fluid is poisonous and
should be stored carefully in marked containers out of the reach of children.
Check the fluid level in the reservoir. The
fluid level should be checked when the
fluid is cold at fluid temperatures of 0 to
308C (32 to 868F). The fluid level can be
checked with the level gauge which is
attached to the cap. To check the fluid
level, remove the cap. The fluid level
1 and MIN
should be between the MAX *
8-14 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(375,1)
BRAKE FLUID
CV37D1-AACA4D78-646F-451E-BC5B-A8705617C0AF
* lines.
2
2 line, add
If the fluid is below the MIN *
Genuine NISSAN E-PSF. Remove the cap
and fill through the opening.
CAUTION
.
Do not overfill.
.
Use Genuine NISSAN E-PSF or equivalent.
For further brake fluid information, see
“Capacities and recommended fluids/lubricants” (P.10-2) of this manual.
WARNING
.
Use only new fluid from a sealed container. Old, inferior or contaminated fluid
may damage the brake system. The use
of improper fluids can damage the brake
system and affect the vehicle’s stopping
ability.
.
Clean the filler cap before removing.
.
Brake fluid is poisonous and should be
stored carefully in marked containers out
of the reach of children.
JVM0731X
CAUTION
Do not spill the fluid on painted surfaces.
This will damage the paint. If fluid is spilled,
wash the surface with water.
Check the fluid level in the reservoir. If the
2 or the brake
fluid is below the MIN line *
warning light comes on, add Genuine
NISSAN Super Heavy Duty Brake Fluid or
equivalent DOT 3 fluid up to the MAX line
1 . If fluid must be added frequently, the
*
system should be checked. It is recommended you visit an INFINITI retailer for
this service.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(376,1)
WINDOW WASHER FLUID
CV37D1-F48FB63A-B6F4-4B11-9059-ECB59D7D5932
To check the window washer fluid level,
1 of the
use your finger to plug the hole *
cap/tube assembly, then remove it from
the reservoir. If there is no fluid in the tube,
add fluid.
Add a washer solvent to the washer for
better cleaning. In the winter season, add a
windshield washer antifreeze. Follow the
manufacturer’s instructions for the mixture
ratio.
JVM0253X
WARNING
To fill the window washer fluid reservoir,
lift the cap off the reservoir and pour the
window washer fluid into the reservoir
opening.
Pre-mix washer fluid concentrates with
water to the manufacturer’s recommended levels before pouring the fluid
into the window washer reservoir. Do not
use the window washer reservoir to mix
the washer fluid concentrate and water.
Refill the reservoir more frequently when
driving conditions require an increased
amount of window washer fluid.
Recommended fluid is Genuine NISSAN
Windshield Washer Concentrate Cleaner &
Antifreeze or equivalent.
Antifreeze is poisonous and should be
stored carefully in marked containers out
of the reach of children.
Fill the window washer fluid reservoir
periodically. Add window washer fluid
when the low window washer fluid warning
appears in the vehicle information display.
.
CAUTION
.
Do not substitute engine anti-freeze
coolant for window washer solution. This
may result in damage to the paint.
.
Do not fill the window washer reservoir
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently stain the grille if spilled while
filling the window washer reservoir.
8-16 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(377,1)
BATTERY
CV37D1-53727028-85F3-446D-8050-B21208C99FC8
. Keep the battery surface clean and dry.
Clean the battery with a solution of
baking soda and water.
. Make certain the terminal connections
are clean and securely tightened.
. If the vehicle is not to be used for 30
days or longer, disconnect the negative
(−) battery terminal cable to prevent
discharging it.
doors. The automatic window adjusting
function will not work, and the side roof
panel may be damaged.
To disconnect the negative (−) battery
terminal, perform the procedure in the
following order. Otherwise, the window
and the side roof panel may contact and be
damaged.
5. Close the driver side door and the
window.
WARNING
.
Do not expose the battery to flames or
electrical sparks. Hydrogen gas generated by the battery is explosive. Do not
allow battery fluid to contact your skin,
eyes, fabrics, or painted surfaces. After
touching a battery or battery cap, do not
touch or rub your eyes. Thoroughly wash
your hands. If the acid contacts your
eyes, skin or clothing, immediately flush
with water for at least 15 minutes and
seek medical attention.
.
2. Vehicle is not driven regularly and/or
only driven short distances.
To connect the negative (−) battery terminal, perform the procedure in the following order. Otherwise, the window and the
side roof panel may contact and be
damaged.
Do not operate the vehicle if the fluid in
the battery is low. Low battery fluid can
cause a higher load on the battery which
can generate heat, reduce battery life,
and in some cases lead to an explosion.
In these cases, the battery may need to be
charged to maintain battery health.
1. Unlock and open the driver side door.
Do not close the door.
.
When working on or near a battery,
always wear suitable eye protection and
remove all jewelry.
.
Battery posts, terminals and related
accessories contain lead and lead compounds. Wash hands after handling.
NOTE:
Care should be taken to avoid situations
that can lead to potential battery discharge and potential no-start conditions
such as:
1. Installation or extended use of electronic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.)
CAUTION
When the battery cable is removed from the
battery terminal, do not close either of front
1. Close the windows.
2. Open the hood.
3. Close and lock all the doors.
4. Disconnect the negative (−) battery
terminal.
5. Securely close the hood.
2. Open the hood.
3. Connect the negative (−) battery terminal. Then close the hood.
4. Fully open the driver side door window.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(378,1)
.
1 to remove the trunk
Remove the clips *
trim as illustrated.
Keep the battery out of the reach of
children.
MAIN BATTERY
LOCATION
CV37D1-09936908-E6EC-4D1F-A9C2-58971CF1F2EB
See “Engine compartment check locations”
(P.8-4) for the battery location.
JVM0722X
AUXILIARY BATTERY LOCATION (for
2.0L turboCV37D1-AEC71B5F-C4E1-4BDB-B727-725A25A32646
gasoline engine models)
CAUTION
.
Do not place the battery in the interior of
the vehicle if you remove the auxiliary
battery.
.
Do not place electrically conductive
objects such as tools around the auxiliary battery.
To check the auxiliary battery, open the
trunk.
8-18 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(379,1)
SDI1480C
DI0137MA
CHECKINGCV37D1-F83CE37A-82DF-4B63-8567-E9A161096A89
BATTERY FLUID LEVEL
Main battery
CV37D1-1E53BBA6-3944-465B-9FF1-A2D880270107
Check the fluid level in each cell (remove
the battery cover if it is necessary). It
1
should be between the UPPER LEVEL *
2 lines.
and LOWER LEVEL *
If it is necessary to add fluid, add only
distilled water to bring the level to the
indicator in each filler opening. Do not
overfill.
1. Remove the cell plugs
A .
*
2. Add distilled water up to the UPPER
1 line.
LEVEL *
If the side of the battery is not clear,
check the distilled water level by
looking directly above the cell; the
1
condition *
indicates OK and the
2 needs more to be added.
conditions *
3. Tighten cell plugs
JVM0729X
Auxiliary battery
A .
*
Vehicles operated in high temperatures or
under severe conditions require frequent
checks of the battery fluid level.
Auxiliary battery (2.0L turbo gasoline engine
models)
CV37D1-E7A734E1-C904-4DAF-9014-C65EDE55440C
.
.
.
A indicates OK.
*
B indicates that charging is necessary.
*
C indicates that replacement is neces*
sary.
If it is necessary to charge or replace the
battery, it is recommended you contact an
INFINITI retailer.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(380,1)
VARIABLE VOLTAGE CONTROL SYSTEM
DRIVE BELTS
CV37D1-EEE1FA47-944D-4234-8652-FA1B4A99ADFC
JUMP STARTING
CV37D1-0AAB0CA9-4991-4590-8F41-F3A34B9AA084
If jump starting is necessary, see “Jump
starting” (P.6-10). If the engine does not
start by jump starting, the battery may
have to be replaced. It is recommended
you visit an INFINITI retailer for this service.
CV37D1-6ADF95B7-2D41-4AEE-99FC-6C4F047C2DAF
CAUTION
.
Do not ground accessories directly to the
battery terminal. Doing so will bypass
the variable voltage control system and
the vehicle battery may not charge
completely.
.
Use electrical accessories with the engine running to avoid discharging the
vehicle battery.
The variable voltage control system measures the amount of electrical discharge
from the battery and controls voltage
generated by the generator.
JVM0655X
1.
2.
3.
4.
5.
VR30DDTT engine
Water pump
Alternator
Drive belt auto-tensioner
Crankshaft pulley
Air conditioner compressor
8-20 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(381,1)
SPARK PLUGS
CV37D1-BAFEF7A1-AE7C-43AA-A355-1FA8A7A79074
ess. If the belt is in poor condition or
loose, have it replaced or adjusted. It is
recommended you visit an INFINITI
retailer for this service.
2. Have the belts checked regularly for
condition and tension in accordance
with the maintenance schedule shown
in the “9. Maintenance and schedules”
section.
Be sure the engine and the ignition switch
are off and that the parking brake is
engaged securely.
CAUTION
Be sure to use the correct socket to remove
the spark plugs. An incorrect socket can
damage the spark plugs.
JVM0433X
1.
2.
3.
4.
5.
WARNING
2.0L turbo gasoline engine
Water pump
Crankshaft pulley
Drive belt auto-tensioner
Air conditioner compressor
Alternator
WARNING
Be sure the ignition switch is in the OFF or
LOCK position before servicing drive belts.
The engine could rotate unexpectedly.
1. Visually inspect each belt for signs of
unusual wear, cuts, fraying or loosenDo-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-21
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(382,1)
AIR CLEANER
CV37D1-EBDFA462-1DEC-47BB-9E1B-9849EB2EE182
Always replace spark plugs with recommended or equivalent ones.
SDI2020
REPLACING
SPARK PLUGS
CV37D1-5A1D3AA1-EC43-4BAE-B27E-C6EBBD832A65
If replacement is required, it is recommended you visit an INFINITI retailer for
this service.
WARNING
.
Operating the engine with the air cleaner
removed can cause you or others to be
burned. The air cleaner not only cleans
the air, it stops flame if the engine
backfires. If it is not there, and the
engine backfires, you could be burned.
Do not drive with the air cleaner
removed, and be careful when working
on the engine with the air cleaner
removed.
.
Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result
in serious injury.
The filter element should not be cleaned
and reused. Replace it according to the
maintenance schedule shown in the “9.
Maintenance and schedules” section.
When replacing the filter, wipe the inside
of the air cleaner housing and the cover
with a damp cloth.
Iridium-tipped
spark plugs
CV37D1-38C2D7CB-E5A3-44D4-8FFC-4A1A5D208F6C
It is not necessary to replace the iridiumtipped spark plugs as frequently as the
conventional type spark plugs since they
will last much longer. Follow the maintenance schedule shown in the “9. Maintenance and schedules” section, but do not
reuse them by cleaning or regapping.
When maintenance is required, it is recommended you contact an INFINITI retailer
for servicing.
8-22 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(383,1)
WINDSHIELD WIPER BLADES
CV37D1-3AAC18CC-496A-4CFC-A885-D20A2F6859E1
CLEANINGCV37D1-7847FFC1-7DCA-4EE2-B775-CA92E386F50A
If your windshield is not clear after
the windshield washer or if a wiper
chatters when running, wax or
material may be on the blade or
shield.
using
blade
other
wind-
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form
when rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild
detergent. Then rinse the blade with clear
water. If your windshield is still not clear
after cleaning the blades and using the
wiper, replace the blades.
Worn windshield wiper blades can damage
the windshield and impair driver vision.
When a washer
nozzle is clogged
CV37D1-A0DFB196-43CC-4C25-AB4E-FF70D87562F0
It is recommended you see an INFINITI
retailer if a washer nozzle is clogged or any
malfunction occurs. Do not attempt to
clean the nozzle using a needle or a pin.
Doing so may damage the nozzle.
SDI2048
REPLACING
CV37D1-2BEC5F4C-D760-4B69-84E3-337BD465F889
Replace the wiper blades if they are worn.
Before replacing the wiper blades, the
wiper should be in the fully up position to
avoid scratching the engine hood or
damaging the wiper arm. To pull up the
wiper arm, see “Wiper and washer switch”
(P.2-37).
1. Pull the wiper arm.
A , and then
2. Push the release tab *
move the wiper blade down the wiper
1 while pushing the release tab
arm *
to remove.
3. Insert the new wiper blade onto the
wiper arm until a click sounds.
4. Rotate the wiper blade so the dimple is
in the groove.
CAUTION
.
After wiper blade replacement, return
the wiper arm to its original position;
otherwise it may be damaged when the
hood is opened.
.
Make sure the wiper blades contact the
glass; otherwise the arm may be daDo-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-23
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(384,1)
BRAKES
CV37D1-4F238978-A678-4BC5-A547-90FB4F14D1F8
maged from wind pressure.
If the brakes do not operate properly, it is
recommended you have the brakes
checked by an INFINITI retailer.
SELF-ADJUSTING
BRAKES
CV37D1-22E38629-DCD8-4E65-AEEF-BF5D3567BF7B
Your vehicle is equipped with self-adjusting brakes.
The disc-type brakes self-adjust every time
the brake pedal is applied.
WARNING
Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is
normal and does not affect the function or
performance of the brake system.
Proper brake inspection intervals should
be followed. For additional information,
see the maintenance schedule shown in
the “9. Maintenance and schedules” section.
Have your brake system checked if the brake
pedal height does not return to normal. It is
recommended you visit an INFINITI retailer
for this service.
BRAKE PAD
WEAR WARNING
CV37D1-D89227A8-C2EA-43BF-8410-9B39CA613024
The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first occur
only when the brake pedal is depressed.
After more wear of the brake pad, the
sound will always be heard even if the
brake pedal is not depressed. Have the
brakes checked as soon as possible if the
wear warning sound is heard.
8-24 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(385,1)
FUSES
CV37D1-29097B28-1FE0-4182-A485-A2047D0C5A2D
JVM0255X
VR30DDTT engine model
JVM0305X
2.0L turbo gasoline engine model
JVM0732X
2.0L turbo gasoline engine model (trunk)
ENGINE COMPARTMENT
CV37D1-AFE79579-EF18-4DDE-B356-BDC18538EFB0
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This could damage the
electrical system or electronic control units
or cause a fire.
JVM0734X
VR30DDTT engine model
JVM0331X
If any electrical equipment does not
operate, check for an open fuse.
2.0L turbo gasoline engine model
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-25
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(386,1)
1. Be sure the ignition switch is placed in
the OFF or LOCK position and the
headlight switch is turned to OFF.
2. Open the engine hood.
3. Remove the fuse/fusible link holder
cover.
4. Remove the fuse with the fuse puller.
SDI1754
A , replace it with a
5. If the fuse is open *
B . Spare fuses are stored in
new fuse *
the passenger compartment fuse box.
6. If a new fuse also opens, have the
electrical system checked and repaired.
It is recommended you visit an INFINITI
retailer for this service.
Fusible links
CV37D1-3E721E86-CD62-4D57-8D17-0637DAF969EF
If any electrical equipment does not
operate and fuses are in good condition,
check the fusible links. If any of these
fusible links are melted, replace only with
genuine INFINITI parts.
8-26 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(387,1)
JVM0256X
PASSENGER
COMPARTMENT
CV37D1-D27C130D-9311-435F-AE5F-9BAD54FDFC82
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This could damage the
electrical system or electronic control units
or cause a fire.
If any electrical equipment does not
operate, check for an open fuse.
Extended storage fuse switch (if so
equipped)CV37D1-9D25C740-4001-4543-BF7B-2B71EA47B8A7
headlight switch is turned to OFF.
2. Open the fuse box lid.
3. Remove the fuse with the fuse puller
A .
*
4. If the fuse is open, replace it with a new
fuse.
5. If a new fuse also opens, have the
electrical system checked and repaired.
It is recommended you visit an INFINITI
retailer for this service. Spare fuses are
stored in the fuse box.
1. Be sure the ignition switch is placed in
the OFF or LOCK position and the
JVM0257X
To reduce battery drain, the extended
storage fuse switch comes from the factory
switched off. Prior to delivery of your
vehicle, the switch is pushed in (switched
on) and should always remain on.
If the extended storage fuse switch is not
pushed in (switched on), the “Shipping
Mode On, Push Storage Fuse” warning may
appear in the vehicle information display.
See “20. Extended storage fuse warning”
(P.2-26).
If any electrical equipment does not
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(388,1)
INTELLIGENT KEY BATTERY REPLACEMENT
CV37D1-0F281EEB-8605-4AC8-B4C1-14A643CAD5F2
operate, remove the extended storage fuse
switch and check for an open fuse.
NOTE:
If the extended storage fuse switch malfunctions or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
CV37D1-513D7F0C-35D0-4880-AB0F-1D9C73274ECD
1. To remove the extended storage fuse
switch, be sure the ignition switch is in
the OFF or LOCK position.
CAUTION
Be careful not to allow children to swallow
the battery and removed parts.
2. Be sure the headlight switch is in the
OFF position.
3. Remove the fuse box cover.
1
4. Pinch the locking tabs *
found on
each side of the storage fuse switch.
JVM0317X
5. Pull the storage fuse switch straight out
2 .
from the fuse box *
To replace the battery:
1. Release the lock knob at the back of the
Intelligent Key and remove the mechanical key.
2. Insert a flat-blade screwdriver wrapped
with a cloth into the slit of the corner
and twist it to separate the upper part
8-28 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(389,1)
(2) this device must accept any interference received, including interference that
may cause undesired operation.
from the lower part.
3. Replace the battery with a new one.
Recommended battery:
NOTE:
CR2032 or equivalent
. Do not touch the internal circuit and
electric terminals as it could cause a
malfunction.
. Hold the battery by the edges.
Holding the battery across the contact points will seriously deplete the
storage capacity.
. Make sure that the + side faces the
bottom of the case.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
SDI2452
4. Align the tips of the upper and lower
1 , and then push them together
parts *
2 until it is securely closed.
*
5. Operate the buttons to check its operation.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
If you need any assistance for replacement,
it is recommended you visit an INFINITI
retailer for this service.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-29
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(390,1)
LIGHTS
1.
2.
3.
4.
5.
6.
7.
8.
CV37D1-1D71E071-0CBD-4E3D-963F-E241DBAFF23C
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Headlight (high-beam)
Headlight (low-beam)
Map light
Front side marker light
Side turn signal light
Emblem light (if so equipped)
Fog light
Parking light, daytime running light
and front turn signal light
Step light
Courtesy light
Tail light
High-mounted stop light
Trunk light
Rear side marker light
Tail/Stop light
Stop light
Rear turn signal light
Back-up light
License plate light
JVM0719X
8-30 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(391,1)
HEADLIGHTS
CV37D1-113147F4-7C9C-41AE-B48B-633089C9360E
If replacement is required, it is recommended you visit an INFINITI retailer for
this service.
Fog may temporarily form inside the lens of
the exterior lights in the rain or in a car
wash. A temperature difference between
the inside and the outside of the lens
causes the fog. This is not a malfunction. If
large drops of water collect inside the lens,
it is recommended you visit an INFINITI
retailer for this service.
EXTERIOR CV37D1-8340E8EC-D475-45A1-B894-36A11A3F29A7
AND INTERIOR LIGHTS
Item
Wattage (W)
Bulb No.
LED
LED
LED
LED
—
—
—
—
LED
LED
LED
—
—
—
LED
LED
LED
LED
LED
LED
LED
LED
1.8
5
2
3.4
LED
LED
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Headlight*
High beams
Low beams
Front fog light*
Parking light/Daytime running light/Front turn
signal light*
Front side marker light*
Front emblem light (if so equipped)*
Side turn signal light*
Rear combination light*
back-up
rear turn signal
tail
stop
tail/stop
rear side marker
License plate light*
Map light*
Vanity mirror light*
Step light
Console box light*
Trunk light
Courtesy light*
High-mounted stop light*
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-31
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(392,1)
*: It is recommended you visit an INFINITI
retailer for replacement.
NOTE: It is recommended that you check
with the Parts Department at an INFINITI
retailer for the latest information about
parts.
Replacement
procedures
CV37D1-CCD7E30B-6B89-488A-B7BD-D5BF37E3F9F9
All other lights are either type A, B, C, D, E
or F. When replacing a bulb, first remove
the lens and/or cover.
SDI1679
8-32 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(393,1)
WHEELS AND TIRES
CV37D1-F1F64E13-82FC-492E-876E-5A66E0C4CA22
If you have a flat tire, see “Flat tire” (P.6-3).
TIRE PRESSURE
CV37D1-CEAD7263-218E-43AE-A248-D60E4433F882
Tire Pressure Monitoring System
(TPMS) CV37D1-ED7310EE-80E6-4118-A2B1-FB086602C102
SDI2330
Step light
This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS). It
monitors tire pressure of all tires except
the spare. When the low tire pressure
warning light is lit and the “Tire Pressure
Low - Add Air” warning appears in the
vehicle information display, one or more of
your tires is significantly under-inflated.
The TPMS will activate only when the
vehicle is driven at speeds above 16 MPH
(25 km/h). Also, this system may not
detect a sudden drop in tire pressure (for
example a flat tire while driving).
For more details, see “Low tire pressure
warning light” (P.2-14),“Tire Pressure Monitoring System (TPMS)” (P.5-5) and “Tire
Pressure Monitoring System (TPMS)” (P.63).
SDI1258A
Trunk light
Tire inflation
pressure
CV37D1-691E0963-E07C-4BA2-A24F-33B6175CC64C
Check the pressure of the tires
(including the spare) often and always prior to long distance trips. The
recommended tire pressure specifications are shown on the Tire and
Loading Information label under the
“Cold Tire Pressure” heading. The
Tire and Loading Information label is
affixed to the driver side center pillar.
Tire pressures should be checked
regularly because:
. Most tires naturally lose air over
time.
. Tires can lose air suddenly when
driven over potholes or other
objects or if the vehicle strikes a
curb while parking.
The tire pressures should be checked
when the tires are cold. The tires are
considered COLD after the vehicle
has been parked for 3 or more hours,
or driven less than 1 mile (1.6 km) at
moderate speeds.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-33
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(394,1)
TPMS with Tire Inflation Indicator
provides visual and audible signals
outside the vehicle for inflating the
tires to the recommended COLD tire
pressure. (See “TPMS with Tire Inflation Indicator” (P.5-8) about the
TPMS with Tire Inflation Indicator.)
Incorrect tire pressure, including
under inflation, may adversely affect
tire life and vehicle handling.
WARNING
. Improperly inflated tires can
fail suddenly and cause an
accident.
. The Gross Vehicle Weight rating (GVWR) is located on the F.
M.V.S.S./C.M.V.S.S. label. The
vehicle weight capacity is
indicated on the Tire and
Loading Information label.
Do not load your vehicle
beyond this capacity. Overloading your vehicle may re-
sult in reduced tire life, unsafe
operating conditions due to
premature tire failure, or unfavorable handling characteristics and could also lead to a
serious accident. Loading beyond the specified capacity
may also result in failure of
other vehicle components.
. Before taking a long trip, or
whenever you heavily load
your vehicle, use a tire pressure gauge to ensure that the
tire pressures are at the specified level.
. For additional information regarding tires, refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.
8-34 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(395,1)
ered COLD after the vehicle has
been parked for 3 or more hours,
or driven less than 1 mile (1.6
km) at moderate speeds. The
recommended cold tire inflation
is set by the manufacturer to
provide the best balance of tire
wear, vehicle handling, driveability, tire noise, etc., up to the
vehicle’s GVWR.
*
5 Tire size — see “Tire labeling”
(P.8-37).
*
6 Spare tire size or compact spare
tire size (if so equipped)
SDI2567
Tire and Loading
Information label
CV37D1-C7BD36AF-9934-43A4-94F2-4EDCBACAF922
*
1 Seating capacity: The maximum
number of occupants that can be
seated in the vehicle.
*
2 Vehicle load limit: See “Vehicle
loading information” (P.10-16).
*
3
Original size: The size of the tires
originally installed on the vehicle at the factory.
*
4 Cold tire pressure: Inflate the
tires to this pressure when the
tires are cold. Tires are considDo-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-35
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(396,1)
** Click HERE to see "Owner's Manual Supplement" **
SDI1949
Checking CV37D1-66CC50EA-50AC-4F6C-9287-E5AD0EB79112
the tire pressure
1. Remove the valve stem cap from
the tire.
2. P r e s s t h e p r e s s u r e g a u g e
squarely onto the valve stem. Do
not press too hard or force the
valve stem sideways, or air will
escape. If the hissing sound of air
escaping from the tire is heard
while checking the pressure, reposition the gauge to eliminate
this leakage.
3. Remove the gauge.
4. Read the tire pressure on the
gauge stem and compare it to
the specification shown on the
Tire and Loading Information label.
5. Add air to the tire as needed. If too
much air is added, press the core
of the valve stem briefly with the
tip of the gauge stem to release
pressure. Recheck the pressure
and add or release air as needed.
6. Install the valve stem cap.
7. Check the pressure of all other
tires, including the spare.
SIZE
P255/40RF19
96V
FRONT
P255/35RF20
ORIGINAL
97V XL
TIRE
255/35RF20
97Y XL
COLD TIRE
INFLATION
PRESSURE
240 kPa,
35 PSI
260 kPa,
38 PSI
260 kPa,
38 PSI
P255/40RF19
96V
240 kPa,
35 PSI
P255/35RF20
REAR
97V XL
ORIGINAL
255/35RF20
TIRE
97Y XL
260 kPa,
38 PSI
260 kPa,
38 PSI
275/30RF20
97Y XL
260 kPa,
38 PSI
SPARE
T145/70R18
TIRE (if so
107M
equipped)
420 kPa,
60 PSI
8-36 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(397,1)
4.
5.
6.
SDI1575
SDI1606
Example
Example
TIRE LABELING
CV37D1-78E5F2E8-A436-4FDD-955A-80CB5766B791
Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This
information identifies and describes
the fundamental characteristics of
the tire and also provides the tire
identification number (TIN) for safety
standard certification. The TIN can be
used to identify the tire in case of a
recall.
*
1 Tire size (example: P215/60R16
94H)
1. P: The “P” indicates the tire is
designed for passenger vehicles.
(Not all tires have this information.)
2. Three-digit number (215): This
number gives the width in millimeters of the tire from sidewall
edge to sidewall edge.
3. Two-digit number (60): This number, known as the aspect ratio,
7.
gives the tire’s ratio of height to
width.
R: The “R” stands for radial.
F: The “F” after “R” indicates SelfSupporting type run-flat tire.
Two-digit number (16): This number is the wheel or rim diameter in
inches.
Two- or three-digit number (94):
This number is the tire’s load
index. It is a measurement of
how much weight each tire can
support. You may not find this
information on all tires because it
is not required by law.
H: Tire speed rating. You should
not drive the vehicle faster than
the tire speed rating.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-37
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(398,1)
4. Three-digit code: Tire type code
(Optional)
5. Four numbers represent the week
and year the tire was built. For
example, the numbers 3103
means the 31st week of 2003. If
these numbers are missing, then
look on the other sidewall of the
tire.
*
3
JVM0694X
Example
*
2
TIN (Tire Identification Number)
for a new tire (example: DOT XX XX
XXX XXXX)
1. DOT: Abbreviation for the “Department of Transportation”. The symbol can be placed above, below or
to the left or right of the Tire
Identification Number.
2. Two-digit code: Manufacturer’s
identification mark
3. Two-digit code: Tire size
Tire ply composition and material
The number of layers or plies of
rubber-coated fabric in the tire.
Tire manufacturers also must indicate the materials in the tire, which
include steel, nylon, polyester, and
others.
*
4 Maximum permissible inflation
pressure
This number is the greatest amount
of air pressure that should be put in
the tire. Do not exceed the maximum
permissible inflation pressure.
*
5
Maximum load rating
This number indicates the maximum
load in kilograms and pounds that
can be carried by the tire. When
replacing the tires on the vehicle,
always use a tire that has the same
load rating as the factory installed
tire.
*
6
Term of “tubeless” or “tube type”
Indicates whether the tire requires an
inner tube (“tube type”) or not
(“tubeless”).
*
7
The word “radial”
The word “radial” is shown, if the tire
has radial structure.
*
8
Manufacturer or brand name
Manufacturer or brand name is
shown.
Other tire-related terminology:
In addition to the many terms that
are defined throughout this section,
Intended Outboard Sidewall is (1) the
8-38 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(399,1)
sidewall that contains a whitewall,
bears white lettering or bears manufacturer, brand and/or model name
molding that is higher or deeper than
the same molding on the other sidewall of the tire, or (2) the outward
facing sidewall of an asymmetrical
tire that has a particular side that
must always face outward when
mounted on a vehicle.
TYPES OF TIRES
CV37D1-91272F19-8064-4509-BD5E-963B83188AFF
WARNING
.
.
When changing or replacing tires, be
sure all four tires are of the same type
(Example: Summer, All Season or Snow)
and construction. An INFINITI retailer
may be able to help you with information
about tire type, size, speed rating and
availability.
Replacement tires may have a lower
speed rating than the factory equipped
tires, and may not match the potential
maximum vehicle speed. Never exceed
the maximum speed rating of the tire.
.
Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
use of SNOW tires or ALL SEASON tires on
all four wheels.
.
For additional information regarding
tires, refer to “Important Tire Safety
Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.
If snow tires are needed, it is necessary to
select tires equivalent in size and load
rating to the original equipment tires. If
you do not, it can adversely affect the
safety and handling of your vehicle.
All seasonCV37D1-D2BE37EF-6F5A-4B3B-A8FF-5D17656B6523
tires
INFINITI specifies all season tires on some
models to provide good performance all
year, including snowy and icy road conditions. All Season tires are identified by ALL
SEASON and/or M&S (Mud and Snow) on
the tire sidewall. Snow tires have better
snow traction than All Season tires and
may be more appropriate in some areas.
Summer tires
CV37D1-082E6388-1E38-4584-ADDC-A51BCEBABB82
INFINITI specifies summer tires on some
models to provide superior performance on
dry roads. Summer tire performance is
substantially reduced in snow and ice.
Summer tires do not have the tire traction
rating M&S on the tire sidewall.
Snow tires
CV37D1-1D7E373A-7843-4F1C-947D-6FDB7147C713
Generally, snow tires will have lower speed
ratings than factory equipped tires and
may not match the potential maximum
vehicle speed. Never exceed the maximum
speed rating of the tire.
If you install snow tires, they must be the
same size, brand, construction and tread
pattern on all four wheels.
For additional traction on icy roads,
studded tires may be used. However, some
U.S. states and Canadian provinces prohibit their use. Check local, state and
provincial laws before installing studded
tires. Skid and traction capabilities of
studded snow tires, on wet or dry surfaces,
may be poorer than that of non-studded
snow tires.
If you plan to operate your vehicle in snowy
or icy conditions, INFINITI recommends the
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-39
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(400,1)
Run-flat tires
CV37D1-345EAC27-88E2-4A5F-BCE8-0CD523D33F00
Your vehicle is equipped with run-flat tires.
You can continue driving to a safe location
even if they are punctured. Always use runflat tires of the specified size on all four
wheels. Mixing tire sizes or construction
may reduce vehicle handling stability. If
necessary, contact an INFINITI retailer for
assistance.
Frequently check the tire pressure and
adjust pressure of each tire properly. The
tire pressure can be also checked in the
vehicle information display.
It can be difficult to tell if a run-flat tire is
under-inflated or flat. Check the tire
pressures as described earlier in this
section. If the tire becomes under-inflated
while driving, the low tire pressure warning
light will illuminate. If the tire becomes flat
while driving, the low tire pressure warning
light and the “Flat Tire - Visit dealer”
warning will appear.
Low tire pressure:
CV37D1-48710C67-7C27-4065-9393-1C3B6C63693D
If the vehicle is being driven with low tire
pressure, the low tire pressure warning
light will illuminate.
Flat tire: CV37D1-6462B965-3245-4F28-BED6-1DEC973DAA88
If the vehicle is being driven with one or
more flat tires, the low tire pressure
warning light will illuminate continuously
and a chime will sound for 10 seconds. A
“Flat Tire - Visit dealer” warning also
appears in the vehicle information display.
The chime will only sound at the first
indication of a flat tire and the warning
light will illuminate continuously. When the
flat tire warning is activated, it is recommended you have the system reset and the
tire checked and replaced if necessary by
an INFINITI retailer. Even if the tire is
inflated to the specified COLD tire pressure, the warning light will continue to
illuminate until the system is reset.
If the low tire pressure warning light
illuminates continuously and the “Flat Tire
- Visit dealer” warning appears in the
vehicle information display:
. Do not exceed 50 MPH (80 km/h).
. Increase your following distance to
allow for increased stopping distances.
. Avoid sudden maneuvers, hard cornering and hard braking.
WARNING
.
Although you can continue driving with a
punctured run-flat tire, remember that
vehicle handling stability is reduced,
which could lead to an accident and
personal injury. Also, driving a long
distance at high speeds may damage
the tire.
.
Do not drive at speeds above 50 MPH (80
km/h) and do not drive more than
approximately 93 miles (150 km) with a
punctured run-flat tire. The actual distance the vehicle can be driven on a flat
tire depends on outside temperature,
vehicle load, road conditions and other
factors.
.
Drive safely at reduced speeds. Avoid
hard cornering or braking, which may
cause you to lose control of the vehicle.
.
If you detect any unusual sounds or
vibrations while driving with a punctured
run-flat tire, pull off the road to a safe
location and stop the vehicle as soon as
possible. The tire may be seriously
damaged and need to be replaced.
8-40 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(401,1)
** Click HERE to see "Owner's Manual Supplement" **
CAUTION
.
Never install tire chains on a punctured
run-flat tire, as this could damage your
vehicle.
.
Avoid driving over any projection or
pothole, as the clearance between the
vehicle and the ground is smaller than
normal.
.
Do not enter an automated car wash with
a punctured run-flat tire.
.
It is recommended you have the punctured tire inspected by an INFINITI retailer
or other authorized repair shop. Replace
the tire as soon as possible if the tire is
seriously damaged.
TIRE CHAINS
CV37D1-47993005-C05E-49C6-A4F7-595D3F032FD5
CAUTION
Tire chains/cables should not be installed
on P255/40RF19, P255/35RF20,
255/35RF20 and 275/30RF20 tires. Doing
so will cause damage to the vehicle. If you
plan to use tire chains/cables, you should
install 245/40RF19 tires on your vehicle.
Use of tire chains may be prohibited
according to location. Check the local laws
before installing tire chains. When installing tire chains, make sure they are the
proper size for the tires on your vehicle and
are installed according to the chain manufacturer’s suggestions. Use only SAE
Class S chains. Class “S” chains are used
on vehicles with restricted tire to vehicle
clearance. Vehicles that can use Class “S”
chains are designed to meet the SAE
standard minimum clearances between
the tire and the closest vehicle suspension
or body component required to accommodate the use of a winter traction device (tire
chains or cables). The minimum clearances
are determined using the factory equipped
tire size. Other types may damage your
vehicle. Use chain tensioners when recommended by the tire chain manufacturer to
ensure a tight fit. Loose end links of the tire
chain must be secured or removed to
prevent the possibility of whipping action
damage to the fenders or underbody. If
possible, avoid fully loading your vehicle
when using tire chains. In addition, drive at
a reduced speed. Otherwise, your vehicle
may be damaged and/or vehicle handling
and performance may be adversely affected.
Tire chains must be installed only on the
rear wheels and not on the front wheels.
Never install tire chains on a TEMPORARY
USE ONLY spare tire (if so equipped). Never
install tire chains on a punctured run-flat
tire (if so equipped), as this could damage
your vehicle.
Do not use tire chains on dry roads. Driving
with tire chains in such conditions can
cause damage to the various mechanisms
of the vehicle due to some overstress.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-41
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(402,1)
The wheel nuts must be kept tightened to the specification at all
times. It is recommended that wheel
nuts be tightened to the specification at each tire rotation interval.
WARNING
SDI1662
CHANGINGCV37D1-F64A9335-FCAE-439A-BB55-D0A891816EF4
WHEELS AND TIRES
Tire rotation (models equipped with
same sizeCV37D1-F7870CCD-932B-47A8-8F27-7722EA305689
tires on all wheels)
INFINITI recommends rotating the
tires every 5,000 miles (8,000 km).
(See “Flat tire” (P.6-3) for tire replacing procedures.)
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
80 ft-lb (108 N·m)
. After rotating the tires, check
and adjust the tire pressure.
. Retighten the wheel nuts
when the vehicle has been
driven for 600 miles (1,000
km) (also in cases of a flat
tire, etc.).
. Do not include the T-type
spare tire or any other small
size spare tire in the tire
rotation.
. For additional information regarding tires, refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada) in the War-
ranty Information Booklet.
After the ignition switch is placed in
the ON position, it may take a period
of time for the tire pressure to be
displayed in the vehicle information
display while the vehicle is driven.
Depending on the radio wave circumstance, tire pressure may not correctly be displayed.
Tire rotation (models equipped with
different size tires on front and
rear)
CV37D1-095D29E5-A723-490B-95E9-4DACE30B04E3
Tires cannot be rotated on this
vehicle, as front tires are a different
size from rear tires.
A pin is on the front brake rotor to
prevent the rear wheels from being
installed in place of the front wheels.
The spare tire can be installed in
place of the front and rear wheels.
When installing the spare tire in the
front wheel, the hole in the spare tire
wheel must be aligned with the pin
8-42 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(403,1)
on the brake rotor.
WARNING
. If your vehicle is equipped
with different size front and
rear tires, never install the
rear tire/wheel on the front of
the vehicle. Doing so can
damage the vehicle or tire.
Damage to the tire may result
in a sudden loss of air pressure which may cause loss of
vehicle control in some driving conditions and cause a
collision and personal injury.
. Retighten the wheel nuts
when the vehicle has been
driven for 600 miles (1,000
km) (also in cases of a flat
tire, etc.).
. For additional information regarding tires, refer to “Important Tire Safety Information”
(US) or “Tire Safety Informa-
tion” (Canada) in the Warranty Information Booklet.
After the ignition switch is placed in
the ON position, it may take a period
of time for the tire pressure to be
displayed in the vehicle information
display while the vehicle is driven.
Depending on the radio wave circumstance, tire pressure may not correctly be displayed.
SDI1663
*
2
*
1
: Wear indicator
: Wear indicator location mark. The
locations are shown by “
”, “TWI”,
etc. depending on tire types.
Tire wear and
damage
CV37D1-58006A64-896F-4DFB-91F4-017EF718D94E
WARNING
. Tires should be periodically
inspected for wear, cracking,
bulging or objects caught in
the tread. If excessive wear,
cracks, bulging or deep cuts
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-43
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(404,1)
.
.
.
.
are found, the tire(s) should
be replaced.
The original tires have built-in
tread wear indicators. When
wear indicators are visible,
the tire(s) should be replaced.
Tires degrade with age and
use. Have tires, including the
spare, over 6 years old
checked by a qualified technician, because some tire damage may not be obvious.
Replace the tires as necessary
to prevent tire failure and
possible personal injury.
Improper service of the spare
tire may result in serious
personal injury. If it is necessary to repair the spare tire, it
is recommended you visit an
INFINITI retailer for this service.
For additional information regarding tires, refer to “Impor-
body-to-tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of
these effects may lead to accidents and
could result in serious personal injury.
tant Tire Safety Information”
(US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.
ReplacingCV37D1-6EFCFC7E-F45A-4C3D-BB51-B8D72A168C0C
wheels and tires
.
For Two-Wheel Drive (2WD) models, if
your vehicle was originally equipped
with 4 tires that were the same size
and you are only replacing 2 of the 4
tires, install the new tires on the rear
axle. Placing new tires on the front axle
may cause loss of vehicle control in
some driving conditions and cause an
accident and personal injury.
.
If the wheels are changed for any reason,
always replace with wheels which have
the same off-set dimension. Wheels of a
different off-set could cause premature
tire wear, degrade vehicle handling
characteristics and/or interference with
the brake discs/drums. Such interference can lead to decreased braking
efficiency and/or early brake pad/shoe
wear. See “Wheels and tires” (P.10-11)
of this manual for wheel off-set dimensions.
.
Since the spare tire is not equipped with
the TPMS, when a spare tire is mounted
or a wheel is replaced, the TPMS will not
When replacing a tire, use the same size,
tread design, speed rating and load carrying capacity as originally equipped. (See
“Specifications” (P.10-10) for recommended types and sizes of tires and
wheels.)
After the ignition switch is placed in the ON
position, it may take a period of time for
the tire pressure to be displayed while the
vehicle is driven. Depending on the radio
wave circumstance, tire pressure may not
correctly be displayed.
WARNING
.
The use of tires other than those
recommended or the mixed use of tires
of different brands, construction (bias,
bias-belted, radial or run-flat), or tread
patterns can adversely affect the ride,
braking, handling, ground clearance,
8-44 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(405,1)
function and the low tire pressure warning light will flash for approximately 1
minute. The light will remain on after 1
minute. Have your tires replaced and/or
TPMS system reset as soon as possible.
It is recommended you visit an INFINITI
retailer for these services.
.
Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
.
The TPMS sensor may be damaged if it is
not handled correctly. Be careful when
handling the TPMS sensor.
.
When replacing the TPMS sensor, the ID
registration may be required. It is
recommended you contact an INFINITI
retailer for ID registration.
.
Do not use a valve stem cap that is not
specified by INFINITI. The valve stem cap
may become stuck.
.
Be sure that the valve stem caps are
correctly fitted. Otherwise the valve may
be clogged up with dirt and cause a
malfunction or loss of pressure.
.
Do not install a damaged or deformed
wheel or tire even if it has been repaired.
Such wheels or tires could have structural damage and could fail without
warning.
.
The use of retread tire is not recommended.
.
For additional information regarding
tires, refer to “Important Tire Safety
Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.
Intelligent All-Wheel Drive (AWD)
models CV37D1-BC31E6C9-B2CE-437F-AE61-B1C7B23E3B16
CAUTION
.
.
Always use tires of the same type, size,
brand, construction (bias, bias-belted or
radial), and tread pattern on all four
wheels. Failure to do so may result in a
circumference difference between tires
on the front and rear axles which will
cause excessive tire wear and may
damage the transmission, transfer case
and differential gears.
ONLY use spare tires specified for the
Intelligent AWD model.
If excessive tire wear is found, it is
recommended that all four tires be replaced with tires of the same size, brand,
construction and tread pattern. The tire
pressure and wheel alignment should also
be checked and corrected as necessary. It
is recommended you visit an INFINITI
retailer for this service.
Wheel balance
CV37D1-D5C0F0AD-B802-4348-80B3-530384ED22AD
Unbalanced wheels may affect vehicle
handling and tire life. Even with regular
use, wheels can get out of balance. Therefore, they should be balanced as required.
Wheel balance service should be performed with the wheels off the vehicle.
Spin balancing the wheels on the vehicle
could lead to mechanical damage.
For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada)
in the INFINITI Warranty Information Booklet.
Care of wheels
CV37D1-28272721-81F4-4572-B5B1-4B07051F02A1
See “Cleaning exterior” (P.7-2) for details
about care of the wheels.
Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
8-45
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(406,1)
Spare tire (TEMPORARY USE ONLY
(T-type) spare
tire) (if so equipped)
CV37D1-BBC25E52-7616-48C3-B40B-A17EDC437007
Since the spare tire is not equipped with
the TPMS, when a spare tire is mounted
(TEMPORARY USE ONLY), the Tire Pressure
Monitoring System (TPMS) will not function.
Observe the following precautions if the
TEMPORARY USE ONLY spare tire must be
used, otherwise your vehicle could be
damaged or involved in an accident.
.
The TEMPORARY USE ONLY spare tire
should be used for emergency use. It
should be replaced with the standard
tire at the first opportunity to avoid
possible tire or differential damage.
.
Drive carefully while the TEMPORARY
USE ONLY spare tire is installed. Avoid
sharp turns and abrupt braking while
driving.
.
Periodically check spare tire inflation
pressure. Always keep the pressure of
the TEMPORARY USE ONLY spare tire at
60 psi (420 kPa, 4.2 bar). Always keep
the pressure of the full size spare tire (if
.
With the TEMPORARY USE ONLY spare
tire installed do not drive your vehicle at
speeds faster than 50 MPH (80 km/h).
Do not use tire chains on a TEMPORARY
USE ONLY spare tire. Tire chains will not
fit properly and may cause damage to
the vehicle.
.
Because the TEMPORARY USE ONLY
spare tire is smaller than the original
tire, ground clearance is reduced. To
avoid damage to the vehicle, do not
drive over obstacles. Also do not drive
the vehicle through an automatic car
wash since it may get caught.
.
When driving on roads covered with
snow or ice, the TEMPORARY USE ONLY
spare tire should be used on the front
wheels and original tire used on the rear
wheels (drive wheels). Use tire chains
only on the two rear original tires.
.
Tire tread of the TEMPORARY USE ONLY
spare tire will wear at a faster rate than
the standard tire. Replace the spare tire
as soon as the tread wear indicators
appear.
.
Do not use the spare tire on other
vehicles.
.
Do not use more than one spare tire at
the same time.
WARNING
.
so equipped) at the recommended pressure for standard tires, as indicated on
the Tire and Loading Information label.
For Tire and Loading Information label
location, see “Tire and loading information label” (P.10-14).
CAUTION
8-46 Do-it-yourself
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(407,1)
9 Maintenance and schedules
Maintenance requirement ...................................
...
General maintenance ......................................
...
Scheduled maintenance ..................................
...
Where to go for service ...................................
...
General maintenance ..........................................
...
Explanation of general maintenance items ......
...
Explanation of scheduled maintenance items ......
...
Emission control system maintenance ............
...
Chassis and body maintenance ......................
...
Maintenance schedules ......................................
...
Additional maintenance items for severe
operating conditions .......................................
...
Condition:
9-2
9-2
9-2
9-2
9-2
9-2
9-5
9-5
9-6
9-7
Oil control system (for VR30DDTT
engine models) .............................................
...
9-7
Standard maintenance .......................................
...
9-8
Emission control system maintenance (for
VR30DDTT engine) .........................................
...
9-9
Emission control system maintenance
(for 2.0L turbo gasoline engine) ..................
...
9-12
Chassis and body maintenance ...................
...
9-14
Maintenance under severe driving conditions ...
... 9-17
Maintenance log ..............................................
...
9-18
9-7
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(408,1)
MAINTENANCE REQUIREMENT
GENERAL MAINTENANCE
CV37D1-1FE91147-D03A-454F-8CE2-41718682DE9E
CV37D1-99388A75-FA9F-4C12-87AA-7212C765E30C
Some day-to-day and regular maintenance
is essential to maintain your vehicle in
good mechanical condition, as well as its
emission and engine performance.
It is the owner’s responsibility to make
sure that the scheduled maintenance, as
well as general maintenance, is performed.
As the vehicle owner, you are the only one
who can ensure that your vehicle receives
the proper maintenance. You are a vital link
in the maintenance chain.
GENERAL CV37D1-9C899EFE-CF7B-44F1-9A3D-78EF760B05BD
MAINTENANCE
General maintenance includes those items
which should be checked during normal
day-to-day operation. They are essential
for proper vehicle operation. It is your
responsibility to perform these procedures
regularly as prescribed.
Performing general maintenance checks
requires minimal mechanical skill and only
a few general automotive tools.
These checks or inspections can be done
by yourself, a qualified technician or, if you
prefer, an INFINITI retailer.
SCHEDULED
MAINTENANCE
CV37D1-4AB86854-3F44-433C-8B66-59A89D3B0CB5
The maintenance items listed in this
section are required to be serviced at
regular intervals. However, under severe
driving conditions, additional or more
frequent maintenance will be required.
WHERE TOCV37D1-340061AC-7165-4FC2-8430-EDF309D4BC76
GO FOR SERVICE
If maintenance service is required or your
vehicle appears to malfunction, have the
systems checked and serviced. It is recommended you visit an INFINITI retailer for
this service.
During the normal day-to-day operation of
the vehicle, general maintenance should
be performed regularly as prescribed in
this section. If you detect any unusual
sounds, vibrations or smells, be sure to
check for the cause, or it is recommended
to have an INFINITI retailer do it promptly.
In addition, it is recommended you visit an
INFINITI retailer if you think that repairs are
required.
When performing any checks or maintenance work, closely observe “Maintenance
precautions” (P.8-3) of this manual.
INFINITI technicians are well-trained specialists and are kept up to date with the
latest service information through technical bulletins, service tips and training
programs. They are completely qualified
to work on INFINITI vehicles before work
begins.
EXPLANATION OF GENERAL MAINTENANCE ITEMS
CV37D1-5D199709-98C9-4BBF-9981-544316382EC9
You can be confident that an INFINITI
retailer’s service department can perform
the service needed to meet the maintenance requirements on your vehicle.
The maintenance items listed here should
be performed from time to time, unless
otherwise specified.
Additional information on the following
items with “*” is found in the “8. Do-ityourself” section of this manual.
Outside the
vehicle
CV37D1-054C55AE-9835-4A7F-8D15-ADE2A8AF882D
Doors and engine hood: Check that all
doors and the engine hood, operate
properly. Also ensure that all latches lock
securely. Lubricate hinges, latches, latch
pins, rollers and links if necessary. Make
sure that the secondary latch keeps the
9-2 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(409,1)
hood from opening when the primary latch
is released.
When driving in areas using road salt or
other corrosive materials, check lubrication
frequently.
Lights*: Clean the headlights on a regular
basis. Make sure that the headlights, stop
lights, tail lights, turn signal lights, and
other lights are all operating properly and
installed securely. Also check headlight
aim.
Road wheel nuts (lug nuts)*: When checking the tires, make sure no wheel nuts are
missing, and check for any loose wheel
nuts. Tighten if necessary.
Tire rotation*: Tires should be rotated
every 5,000 miles (8,000 km). If your
vehicle is equipped with different sized
tires in the front and rear, tires cannot be
rotated.
Tires*: Check the pressure with a gauge
often and always prior to long distance
trips. If necessary, adjust the pressure in
all tires, including the spare, to the
pressure specified. Check carefully for
damage, cuts or excessive wear.
Tire Pressure Monitoring System (TPMS)
transmitter components: Replace the
TPMS transmitter grommet seal, valve core
and cap when the tires are replaced due to
wear or age.
Inside the
vehicle
CV37D1-42334435-BDC5-4B4B-BA49-0B1C06D00D3D
Wheel alignment and balance: If the
vehicle should pull to either side while
driving on a straight and level road, or if
you detect uneven or abnormal tire wear,
there may be a need for wheel alignment.
Accelerator pedal: Check the pedal for
smooth operation and make sure the pedal
does not catch or require uneven effort.
Keep the floor mat away from the pedal.
If the steering wheel or seat vibrates at
normal highway speeds, wheel balancing
may be needed.
For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada)
in the INFINITI Warranty Information Booklet.
Windshield: Clean the windshield on a
regular basis. Check the windshield at
least every six months for cracks or other
damage. Have a damaged windshield
repaired by a qualified repair facility.
Windshield wiper blades*: Check for
cracks or wear if they do not wipe properly.
The maintenance items listed here should
be checked on a regular basis, such as
when performing scheduled maintenance,
cleaning the vehicle, etc.
Automatic transmission P (Park) mechanism: On a fairly steep hill, check that your
vehicle is held securely with the shift lever
in the P (Park) position without applying
any brakes.
Brake pedal: Check the pedal for smooth
operation. If the brake pedal suddenly
goes down further than normal, the pedal
feels spongy or the vehicle seems to take
longer to stop, have your vehicle checked
immediately. It is recommended you visit
an INFINITI retailer for this service. Keep
the floor mat away from the pedal.
Brakes: Check that the brakes do not pull
the vehicle to one side when applied.
Parking brake: Check the parking brake
operation regularly. The vehicle should be
securely held on a fairly steep hill with only
the parking brake applied. If the parking
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(410,1)
brake needs adjusted, it is recommended
you visit an INFINITI retailer for this service.
Seats: Check seat position controls such as
seat adjusters, seatback recliner, etc. to
ensure they operate smoothly and that all
latches lock securely in every position.
Check that the head restraints move up
and down smoothly and that the locks (if
so equipped) hold securely in all latched
positions.
Seat belts: Check that all parts of the seat
belt system (for example, buckles, anchors, adjuster and retractors) operate
properly and smoothly, and are installed
securely. Check the belt webbing for cuts,
fraying, wear or damage.
Steering wheel: Check for changes in the
steering conditions, such as excessive free
play, hard steering or strange noises.
Warning lights and chimes: Make sure that
all warning lights and chimes are operating
properly.
Windshield defroster: Check that the air
comes out of the defroster outlets properly
and in sufficient quantity when operating
the heater or air conditioner.
9-4
Windshield wiper and washer*: Check that
the wipers and washer operate properly
and that the wipers do not streak.
Brake fluid level*: Make sure that the
brake fluid level is between the MAX and
MIN lines on the reservoir.
Under theCV37D1-B3361551-A047-4A72-ACCF-65F901F88160
hood and vehicle
Engine coolant level*: Check the coolant
level when the engine is cold.
The maintenance items listed here should
be checked periodically (for example, each
time you check the engine oil or refuel).
Battery*: Check the fluid level in each cell.
It should be between the MAX and MIN
lines. Vehicles operated in high temperatures or under severe condition require
frequent checks of the battery fluid level.
NOTE:
Care should be taken to avoid situations
that can lead to potential battery discharge and potential no-start conditions
such as:
1. Installation or extended use of electronic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.)
2. Vehicle is not driven regularly and/or
only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Intercooler coolant level*: Check the coolant level when the engine is cold.
Engine drive belts*: Make sure that no belt
is frayed, worn, cracked or oily.
Engine oil level*: Check the level after
parking the vehicle on a level spot and
turning off the engine. Wait more than 15
minutes for the oil to drain back into the oil
pan.
Exhaust system: Make sure there are no
loose supports, cracks or holes. If the
sound of the exhaust seems unusual or
there is a smell of exhaust fumes, immediately have the exhaust system inspected.
It is recommended you visit an INFINITI
retailer for this service. (See “Precautions
when starting and driving” (P.5-4).)
Fluid leaks: Check under the vehicle for
fuel, oil, water or other fluid leaks after the
vehicle has been parked for a while. Water
dripping from the air conditioner after use
is normal. If you should notice any leaks or
if gasoline fumes are evident, check for the
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(411,1)
EXPLANATION OF SCHEDULED
MAINTENANCE ITEMS
CV37D1-2CF80F6D-4B7A-4EF0-B189-36C37BC3388B
cause and have it corrected immediately.
Power steering fluid level* and lines:
Check the level when the fluid is cold, with
the engine off. Check the lines for proper
attachment, leaks, cracks, etc.
Radiator and hoses: Check the front of the
radiator and clean off any dirt, insects,
leaves, etc., that may have accumulated.
Make sure the hoses have no cracks,
deformation, rot or loose connections.
Underbody: The underbody is frequently
exposed to corrosive substances such as
those used on icy roads or to control dust.
It is very important to remove these
substances, otherwise rust will form on
the floor pan, frame, fuel lines and around
the exhaust system. At the end of winter,
the underbody should be thoroughly
flushed with plain water, being careful to
clean those areas where mud and dirt may
accumulate. For additional information,
see “Cleaning exterior” (P.7-2).
Windshield washer fluid*: Check that there
is adequate fluid in the reservoir.
The following descriptions are provided to
give you a better understanding of the
scheduled maintenance items that should
be regularly checked or replaced. The
maintenance schedule indicates at which
mileage/time intervals each item requires
service.
In addition to scheduled maintenance,
your vehicle requires that some items be
checked during normal day-to-day operation. Refer to “General maintenance” (P.92).
Items marked with “*” are recommended
by INFINITI for reliable vehicle operation.
You are not required to perform maintenance on these items in order to maintain
the warranties which come with your
vehicle. Other maintenance items and
intervals are required.
When applicable, additional information
can be found in the “8. Do-it yourself”
section of this manual.
NOTE:
INFINITI does not advocate the use of nonOEM approved aftermarket flushing systems and strongly advises against performing these services on an INFINITI
product. Many of the aftermarket flushing
systems use non-OEM approved chemicals
or solvents, the use of which has not been
validated by INFINITI.
For recommended fuel, lubricants, fluids,
grease, and refrigerant, refer to “Capacities and recommended fluids/lubricants”
(P.10-2) of this manual.
EMISSION CONTROL SYSTEM
MAINTENANCE
CV37D1-A34BF4AF-C3A9-418C-8791-C1F7FEBCED15
Drive belts*:
Check engine drive belts for wear, fraying
or cracking and for proper tension. Replace
any damaged drive belts.
Engine air filter:
Replace at specified intervals. When driving for prolonged periods in dusty conditions, check/replace the filter more
frequently.
Engine coolant* (for VR30DDTT engine
models):
Replace coolant at the specified interval.
When adding or replacing coolant, be sure
to use only Genuine NISSAN Long Life
Antifreeze/Coolant (blue) or equivalent
with the proper mixture. (Refer to “Engine
cooling system (for VR30DDTT engine
models)” (P.8-6) to determine the proper
mixture for your area.)
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(412,1)
NOTE:
(P.10-2).
maged parts immediately.
Mixing any other type of coolant or the use
of non-distilled water may reduce the
recommended service interval of the coolant.
Engine valve clearance*:
Exhaust system:
Inspect only if valve noise increases.
Adjust valve clearance if necessary.
Visually inspect the exhaust pipes, muffler
and hangers for leaks, cracks, deterioration, and damage. Tighten connections or
replace parts as necessary.
Engine coolant* (for 2.0L turbo gasoline
engine models):
Replace coolant at the specified interval.
When adding or replacing coolant, be sure
to use only BASF Glysantin® G48® or
equivalent with the proper mixture. (Refer
to “Engine cooling system (for 2.0L turbo
gasoline engine models)” (P.8-8) to determine the proper mixture for your area.)
Evaporative emissions control vapor
lines*:
Check vapor lines for leaks or looseness.
Tighten connections or replace parts as
necessary.
Fuel lines*:
Check the fuel hoses, piping and connections for leaks, looseness, or deterioration.
Tighten connections or replace parts as
necessary.
NOTE:
Spark plugs:
Mixing any other type of coolant or the use
of non-distilled water may reduce the
recommended service interval of the coolant.
Replace at specified intervals. Install new
plugs of the type as originally equipped.
Intercooler coolant (for VR30DDTT engine
models):
Brake lines and cables:
Intercooler coolant is maintenance-free.
Engine oil and oil filter:
Replace engine oil and oil filter at the
specified intervals. For recommended oil
grade and viscosity refer to “Capacities
and recommended fluids/lubricants”
9-6
CHASSIS CV37D1-1DEF0C0C-EB1B-4682-A5E7-974AA878EAED
AND BODY MAINTENANCE
Visually inspect for proper installation.
Check for chafing, cracks, deterioration,
and signs of leaking. Replace any deteriorated or damaged parts immediately.
Brake pads, rotors, drums and linings:
In-cabin microfilter:
Replace at specified intervals. When driving for prolonged periods in dusty conditions, replace the filter more frequently.
Propeller shaft(s):
Check for damage, looseness, and grease
leakage. (4WD/AWD/RWD)
Steering gear and linkage, axle and
suspension parts, drive shaft boots:
Check for damage, looseness, and leakage
of oil or grease. Under severe driving
conditions, inspect more frequently.
Tire rotation:
Tires should be rotated every 5,000 miles
(8,000 km) according to the instructions
under “Explanation of general maintenance items” (P.9-2). When rotating tires,
check for damage and uneven wear. Replace if necessary.
Check for wear, deterioration and fluid
leaks. Replace any deteriorated or da-
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(413,1)
MAINTENANCE SCHEDULES
CV37D1-4887AC70-6441-4091-A620-C5705BB029DC
Transmission fluid/oil, differential oil and
transfer case oil:
Visually inspect for signs of leakage at
specified intervals.
To help ensure smooth, safe and economical driving, INFINITI provides two maintenance schedules that may be used,
depending upon the conditions in which
you usually drive. These schedules contain
both distance and time intervals, up to
120,000 miles (192,000 km)/144 months.
For most people, the odometer reading will
indicate when service is needed. However,
if you drive very little, your vehicle should
be serviced at the regular time intervals
shown in the schedule.
After 120,000 miles (192,000 km)/144
months, continue maintenance at the
same mileage/time intervals.
ADDITIONAL MAINTENANCE ITEMS
FOR SEVERE OPERATING CONDITIONS
CV37D1-68261FC9-F3ED-40B4-A472-2CE9EAFD0080
Additional maintenance items for severe
operating conditions; should be performed
on vehicles that are driven under especially
demanding conditions. Additional maintenance items should be performed if you
primarily operate your vehicle under the
following conditions:
. Repeated short trips of less than 5
miles (8 km).
. Repeated short trips of less than 10
miles (16 km) with outside temperatures remaining below freezing.
. Operating in hot weather in stop-and-go
“rush hour” traffic.
. Extensive idling and/or low speed driving for long distances, such as police,
taxi or door-to-door delivery use.
. Driving in dusty conditions.
. Driving on rough, muddy or salt spread
roads.
. Using a car-top carrier.
NOTE:
For vehicles operated in Canada, both
standard and severe maintenance items
should be performed at every interval.
OIL CONTROL SYSTEM (for
VR30DDTT
engine models)
CV37D1-07BE1CE8-2886-4F9D-B2C1-75394A31CCAB
Your vehicle is equipped with oil control
system. It calculates engine oil and filter
change interval based on driving conditions. Driving in severe conditions will
shorten the engine oil and filter change
interval. When the oil replacement indicator appears in the vehicle information
display, the engine oil and filter need to
be replaced.
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(414,1)
STANDARD MAINTENANCE
CV37D1-4F4CD256-3095-4D94-B7C6-54D297CA6696
The following tables show the standard
maintenance schedule. Depending upon
weather and atmospheric conditions, varying road surfaces, individual driving habits
and vehicle usage, additional or more
frequent maintenance may be required.
After 120,000 miles (192,000 km)/144
months, continue maintenance at the
same mileage/time intervals.
9-8
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(415,1)
EMISSIONCV37D1-6A327679-8B81-4831-9992-3E8495792E9D
CONTROL SYSTEM MAINTENANCE (for VR30DDTT engine)
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATION Miles 6 1,000
(km 6 1,000)
Perform at number of
Months
miles, kilometers or
months, whichever comes
first.
Drive belts
See NOTE (1)
Air cleaner filter
See NOTE (2)
MAINTENANCE INTERVAL
5
(8)
6
10
(16)
12
15
(24)
18
20
(32)
24
25
(40)
30
30
(48)
36
35
(56)
42
40
(64)
48
I*
45
(72)
54
50
(80)
60
55
(88)
66
60
(96)
72
I*
R
I*
R
EVAP vapor lines
I*
I*
I*
Fuel lines
I*
I*
I*
Fuel filter
Engine coolant*
See NOTE (3)
See NOTE (4)(5)
Engine oil
See NOTE (6)
R
R
R
R
R
R
Engine oil filter
See NOTE (6)
R
R
R
R
R
R
Spark plugs
See NOTE (7)
Intake and exhaust valve
clearance*
See NOTE (8)
Replace every 105,000 miles (168,000 km)
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(416,1)
MAINTENANCE OPERATION Miles 6 1,000
(km 6 1,000)
Perform at number of
Months
miles, kilometers or
months, whichever comes
first.
Drive belts
See NOTE (1)
Air cleaner filter
See NOTE (2)
MAINTENANCE INTERVAL
65
(104)
78
70
(112)
84
I*
75
(120)
90
80
(128)
96
I*
85
(136)
102
90
(144)
108
95
(152)
114
I*
100
(160)
120
I*
105
(168)
126
110
(176)
132
I*
R
115
(184)
138
120
(192)
144
I*
R
EVAP vapor lines
I*
I*
I*
Fuel lines
I*
I*
I*
Fuel filter
Engine coolant*
See NOTE (3)
See NOTE (4)(5)
Engine oil
See NOTE (6)
R
R
R
R
R
R
Engine oil filter
See NOTE (6)
R
R
R
R
R
R
Spark plugs
See NOTE (7)
Intake and exhaust valve
clearance*
See NOTE (8)
NOTE:
(1) After 40,000 miles (64,000 km) or 48
months, inspect every 10,000 miles
(16,000 km) or 12 months. Replace the
drive belts if found damaged.
(2) If operating mainly in dusty conditions,
more frequent maintenance may be required.
(3) Periodic maintenance is not required.
Replace every 105,000 miles (168,000 km)
(4) First replacement interval is 105,000
miles (168,000 km) or 84 months. After
first replacement, replace every 75,000
miles (120,000 km) or 60 months.
(5) Use only Genuine NISSAN Long Life
Antifreeze/Coolant (blue) or equivalent
with proper mixture ratio of 50% antifreeze and 50% demineralized or distilled
water. Mixing any other type of coolant or
the use of non-distilled water may reduce
the life expectancy of the factory fill
coolant.
(6) If the oil replacement indicator is
displayed, change the engine oil and filter
as soon as possible. After replacing the
engine oil, reset the display.
(7) Replace spark plug when the plug gap
exceeds 0.043 in (1.1 mm) even if within
9-10 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(417,1)
specified replacement mileage.
(8) Periodic maintenance is not required.
However, if valve noise increases, inspect
valve clearance.
*: Maintenance items and intervals with
“*” are recommended by INFINITI for
reliable vehicle operation. The owner need
not to perform such maintenance in order
to maintain the emission warranty or
manufacturer recall liability. Other maintenance items and intervals are required.
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(418,1)
EMISSIONCV37D1-890F161E-DC56-4909-A3F0-93FDB448E87C
CONTROL SYSTEM MAINTENANCE (for 2.0L turbo gasoline engine)
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATION Miles 6 1,000
(km 6 1,000)
Perform at number of
Months
miles, kilometers or
months, whichever comes
first.
Engine compartment
V-belt
MAINTENANCE INTERVAL
5
(8)
6
10
(16)
12
See NOTE (1)
See NOTE (2)
15
(24)
18
20
(32)
24
25
(40)
30
30
(48)
36
35
(56)
42
40
(64)
48
45
(72)
54
55
(88)
66
60
(96)
72
I
I
I
I*
I*
I*
Air cleaner filter
Replace every 45,000 miles (72,000 km) or 36 months
Fuel lines
I*
Fuel filter
50
(80)
60
I*
I*
See NOTE (3)
Engine coolant*
Replace every 120,000 miles (192,000 km) or 120 months
Engine oil
R
R
R
R
R
R
Engine oil filter
R
R
R
R
R
R
Spark plugs
Replace every 45,000 miles (72,000 km) or 36 months
9-12 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(419,1)
MAINTENANCE OPERATION Miles 6 1,000
(km 6 1,000)
Perform at number of
Months
miles, kilometers or
months, whichever comes
first.
Engine compartment
V-belt
MAINTENANCE INTERVAL
65
(104)
78
70
(112)
84
75
(120)
90
80
(128)
96
85
(136)
102
90
(144)
108
95
(152)
114
100
(160)
120
105
(168)
126
115
(184)
138
120
(192)
144
See NOTE (1)
I
I
I
See NOTE (2)
I*
I*
I*
Air cleaner filter
Replace every 45,000 miles (72,000 km) or 36 months
Fuel lines
I*
Fuel filter
110
(176)
132
I*
I*
See NOTE (3)
Engine coolant*
Replace every 120,000 miles (192,000 km) or 120 months
Engine oil
R
R
R
R
R
R
Engine oil filter
R
R
R
R
R
R
Spark plugs
NOTE:
(1) All visible parts checked for leaks and
damage.
Replace every 45,000 miles (72,000 km) or 36 months
manufacturer recall liability. Other maintenance items and intervals are required.
(2) In visible area only.
(3) Periodic maintenance is not required.
*: Maintenance items and intervals with
“*” are recommended by INFINITI for
reliable vehicle operation. The owner need
not to perform such maintenance in order
to maintain the emission warranty or
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(420,1)
CHASSIS CV37D1-7FA7BB02-2AFC-40C4-B1B0-95B3B6AE8223
AND BODY MAINTENANCE
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATION Miles 6 1,000
(km 6 1,000)
Perform at of miles, kiloMonths
meters or months, whichever comes first.
MAINTENANCE INTERVAL
5
(8)
6
10
(16)
12
15
(24)
18
20
(32)
24
25
(40)
30
30
(48)
36
35
(56)
42
40
(64)
48
45
(72)
54
50
(80)
60
55
(88)
66
60
(96)
72
Brake lines and cables
I
I
I
I
I
I
Brake pads and rotors$
I
I
I
I
I
I
Brake fluid$
R
Automatic transmission
fluid
See NOTE (1)
Transfer fluid and differential gear oil
See NOTE (2)
I
I
Steering gear and linkage,
axle and suspension parts
$
Tire rotation
I
I
R
I
I
I
I
I
See NOTE (3)
Propeller shaft and drive
shaft boots (AWD models)
$
I
I
Exhaust system$
I
I
In-cabin microfilter
Stop lamp switch and
brake pedal position
R
R
See NOTE (4)
Intelligent Key battery
I
I
I
R
I
R
I
I
R
I
I
R
I
R
I
R
I
R
9-14 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(421,1)
MAINTENANCE OPERATION
Perform at of miles, kilometers or months, whichever comes first.
Miles 6 1,000
(km 6 1,000)
Months
MAINTENANCE INTERVAL
65
(104)
78
70
(112)
84
75
(120)
90
80
(128)
96
85
(136)
102
90
(144)
108
95
(152)
114
100
(160)
120
105
(168)
126
110
(176)
132
115
(184)
138
120
(192)
144
Brake lines & cables
I
I
I
I
I
I
Brake pads & rotors$
I
I
I
I
I
I
Brake fluid$
R
Automatic transmission
fluid
See NOTE (1)
Transfer fluid & differential
gear oil
See NOTE (2)
I
I
Steering gear & linkage,
axle & suspension parts$
Tire rotation
I
I
I
I
I
I
I
In-cabin microfilter
I
R
See NOTE (4)
I
I
I
R
[ Edit: 2016/ 4/ 27
I
I
I
R
I
R
I
R
I
R
I
R
Maintenance and schedules
Condition:
I
See NOTE (3)
Exhaust system$
Intelligent Key battery
I
I
Propeller shaft & drive
shaft boots (AWD models)
$
Stop lamp switch and brake
pedal position
R
R
I
R
9-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(422,1)
NOTE:
Maintenance items with “$” should be
performed more frequently according to
“Maintenance under severe driving conditions” (P.9-17).
(1) Periodic maintenance is not required.
(2) If using a car-top carrier, or driving on
rough or muddy roads, change (not just
inspect) oil at every 20,000 miles (32,000
km) or 24 months.
(3) Refer to “Tire rotation” under “General
maintenance” (P.9-2).
(4) Inspect the clearance between the
brake pedal and the switches.
9-16 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(423,1)
MAINTENANCE UNDER SEVERE DRIVING
CONDITIONS
CV37D1-C4531581-C30A-4BAC-A651-028775A6355E
The maintenance intervals shown on the
preceding pages are for normal operating
conditions. If the vehicle is mainly operated under severe driving conditions as
shown below, more frequent maintenance
must be performed on the following items
as shown in the table.
Severe driving conditions
Maintenance item
Maintenance operation
Maintenance interval
Brake fluid
Replace
Every 10,000 miles (16,000 km) or 12 months
Brake pads & rotors
Inspect
Every 5,000 miles (8,000 km) or 6 months
Steering gear & linkage, axle &
suspension parts
Inspect
Every 5,000 miles (8,000 km) or 6 months
Propeller shaft & drive shaft boots
(AWD models)
Inspect
Every 5,000 miles (8,000 km) or 6 months
Exhaust system
Inspect
Every 5,000 miles (8,000 km) or 6 months
. Repeated short trips of less than 5
miles (8 km).
. Repeated short trips of less than 10
miles (16 km) with outside temperatures remaining below freezing.
. Operating in hot weather in stop-and-go
“rush hour” traffic.
. Extensive idling and/or low speed driving for long distances, such as police,
taxi or door-to-door delivery use.
. Driving in dusty conditions.
. Driving on rough, muddy, or salt spread
roads.
. Using a car-top carrier.
Maintenance operation: Inspect = Inspect
and correct or replace as necessary.
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(424,1)
MAINTENANCE LOG
CV37D1-22EBB2E3-CBAA-4958-A208-4316F19DB706
5,000 Miles (8,000 km) or 6 Months
10,000 Miles (16,000 km) or 12 Months
15,000 Miles (24,000 km) or 18 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
20,000 Miles (32,000 km) or 24 Months
25,000 Miles (40,000 km) or 30 Months
30,000 Miles (48,000 km) or 36 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
35,000 Miles (56,000 km) or 42 Months
40,000 Miles (64,000 km) or 48 Months
45,000 Miles (72,000 km) or 54 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
9-18 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(425,1)
50,000 Miles (80,000 km) or 60 Months
55,000 Miles (88,000 km) or 66 Months
60,000 Miles (96,000 km) or 72 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
65,000 Miles (104,000 km) or 78 Months
70,000 Miles (112,000 km) or 84 Months
75,000 Miles (120,000 km) or 90 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
80,000 Miles (128,000 km) or 96 Months
85,000 Miles (136,000 km) or 102 Months
90,000 Miles (144,000 km) or 108 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
9-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(426,1)
95,000 Miles (152,000 km) or 114 Months
100,000 Miles (160,000 km) or 120 Months
105,000 Miles (168,000 km) or 126 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
110,000 Miles (176,000 km) or 132 Months
115,000 Miles (184,000 km) or 138 Months
120,000 Miles (192,000 km) or 144 Months
Retailer Name:
Retailer Name:
Retailer Name:
Date:
Date:
Date:
Mileage:
Mileage:
Mileage:
Retailer
Stamp:
Retailer
Stamp:
Retailer
Stamp:
9-20 Maintenance and schedules
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(427,1)
10 Technical and consumer information
Capacities and
recommended fluids/lubricants ........................
...
10-2
Fuel information ...........................................
...
10-4
Engine oil and oil filter recommendation .......
...
10-7
Air conditioning system refrigerant and
lubricant recommendations ..........................
...
10-9
Specifications .................................................
...
10-10
Engine ........................................................
...
10-10
Wheels and tires ........................................
...
10-11
Dimensions ................................................
...
10-11
When traveling or registering in
another country ..............................................
...
10-12
Vehicle identification ......................................
...
10-12
Vehicle Identification Number (VIN) plate ....
... 10-12
Vehicle identification number
(chassis number) ........................................
...
10-12
Engine serial number ..................................
...
10-13
F.M.V.S.S./C.M.V.S.S. certification label .......
...
10-13
Emission control information label ..............
...
10-14
Tire and loading information label ..............
...
10-14
Air conditioner specification label ...............
...
10-14
Condition:
Installing front license plate ...........................
...
Removing air deflectors ..................................
...
Vehicle loading information ............................
...
Terms .......................................................
...
Vehicle load capacity ................................
...
Loading tips ..............................................
...
Measurement of weights ...........................
...
Towing a trailer ..............................................
...
Flat towing ................................................
...
Uniform tire quality grading ...........................
...
Treadwear .................................................
...
Traction AA, A, B and C .............................
...
Temperature A, B and C ............................
...
Emission control system warranty ..................
...
Reporting safety defects .................................
...
Readiness for Inspection/Maintenance (I/M)
test (US only) .................................................
...
Event Data Recorders (EDR) ............................
...
Owner’s Manual/Service Manual
order information ...........................................
...
[ Edit: 2016/ 4/ 27
10-15
10-15
10-16
10-16
10-17
10-18
10-19
10-19
10-19
10-20
10-20
10-20
10-20
10-21
10-21
10-22
10-23
10-24
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(428,1)
CAPACITIES AND RECOMMENDED FLUIDS/
LUBRICANTS
CV37D1-C061365F-EF7D-4287-BD30-362698201633
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure
instructed in the “8. Do-it-yourself” section to determine the proper refill capacity.
Fluid types
Fuel
Engine oil*1
Drain and refill
*1
: For additional information, see “Engine oil” (P.810).
Engine coolant
VR30DDTT engine
model
Two-Wheel
Drive (2WD)
model
With oil filter
change
Without oil filter
change
All-Wheel Drive With oil filter
(AWD) model change
Without oil filter
change
2.0L turbo gaso- Two-Wheel
With oil filter
line engine model Drive (2WD)
change
model
Without oil filter
change
All-Wheel Drive With oil filter
(AWD) model change
Without oil filter
change
VR30DDTT engine Standard and Total (with reservoir)
model
premium
grade
Reservoir
Sport grade
Total (with reservoir)
Reservoir
2.0L turbo gaso- Total (with reservoir)
line engine model
Reservoir
Intercooler coolant
Total (with reservoir)
Reservoir
Capacity (Approximate)
US measure
Imp measure
20 gal
16-5/8 gal
5-1/8 qt
4-1/4 qt
Liter
76
4.8
4-7/8 qt
4 qt
4.6
5-3/4 qt
4-3/4 qt
5.4
5-1/2 qt
4-5/8 qt
5.2
6-5/8 qt
5-1/2 qt
6.3
6-1/8 qt
5-1/8 qt
5.8
7 qt
5-7/8 qt
6.6
6-1/2 qt
5-3/8 qt
6.1
9-1/4 qt
7-3/4 qt
8.8
5/8 qt
10-7/8 qt
1/2 qt
9-1/8 qt
0.6
10.3
5/8 qt
9-1/2 qt
1/2 qt
7-7/8 qt
0.6
9.0
1 qt
3/4 qt
0.9
3-3/8 qt
3/8 qt
2-7/8 qt
3/8 qt
3.2
0.4
Recommended fluids and lubricants
· See “Fuel information” (P.10-4).
· Genuine NISSAN engine oil or equivalent
· Engine oil with API Certification Mark*2, SAE Viscosity 0W-20*3
*2
: For additional information, refer to “Engine oil and oil filter
recommendation” (P.10-7) of this manual.
*3
: As an alternative to this recommended oil, SAE 5W-30 conventional
petroleum oils may be used and meet all specifications and requirements
necessary to maintain the INFINITI new vehicle limited warranty.
· Engine oil meeting specification MB229.5, viscosity SAE 0W-30 or
equivalent.
· As an alternative to this recommended oil, engine oils meeting
specification MB229.5, viscosity SAE 0W-40, 5W-30 and 5W-40 may be
used and meet all specifications and requirements necessary to maintain
the new vehicle limited warranty.
· For additional information, refer to “Selecting the correct oil” (P.10-8)
and “Oil viscosity” (P.10-8) under “Engine oil and oil filter recommendation” (P.10-7) of this manual.
· Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or
equivalent
· BASF Glysantin® G48®
· Use BASF Glysantin® G48® or equivalent in its quality. Any damage to the
vehicle or within the engine cooling system caused by the use of engine
coolant other than as recommended is not covered under the INFINITI’s
new vehicle limited warranty.
· Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or
equivalent
10-2 Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(429,1)
Fluid types
Automatic Transmission Fluid (ATF)
Differential gear oil
Capacity (Approximate)
US measure
Imp measure
—
—
Liter
—
Front
—
—
—
Rear
—
—
—
—
—
—
Transfer fluid
Brake fluid
Refill to the proper oil level according to the
instructions in the “8. Do-it-yourself” section.
Power steering fluid
Multi-purpose grease
Air conditioning system refrigerant
—
—
—
—
—
—
Air conditioning system lubricants
Window washer fluid
—
—
—
—
—
—
Recommended fluids and lubricants
· Genuine NISSAN Matic S ATF
· INFINITI recommends using Genuine NISSAN Matic S ATF ONLY in INFINITI
automatic transmissions. Do not mix with other fluids. Using fluids that
are not equivalent to Genuine NISSAN Matic S ATF may damage the
automatic transmission. Damage caused by the use of fluids other than
as recommended is not covered under the INFINITI’s new vehicle limited
warranty.
· Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or equivalent
conventional (non-synthetic) oil.
· API GL-5 Synthetic gear oil, Viscosity SAE 75W-90
· Genuine NISSAN Matic J ATF
· INFINITI recommends using Genuine NISSAN Matic J ATF ONLY in INFINITI
transfers. Do not mix with other fluids. Using fluids that are not
equivalent to Genuine NISSAN Matic J ATF may damage the transfer.
Damage caused by the use of fluids other than as recommended is not
covered under the INFINITI’s new vehicle limited warranty.
· Genuine NISSAN Super Heavy Duty Brake Fluid*4 or equivalent DOT 3
*4
: Available in mainland U.S.A. through an INFINITI retailer.
· Genuine NISSAN E-PSF or equivalent
· Use of a power steering fluid other than Genuine NISSAN E-PSF may
prevent the power steering system from operating properly.
· NLGI No. 2 (Lithium soap base)
· HFC-134a (R-134a)
For additional information, see “Vehicle identification” (P.10-12) for air
conditioner specification label.
· NISSAN A/C System Oil PAG or exact equivalent
· Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or
equivalent
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-3
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(430,1)
FUEL INFORMATION
CV37D1-211E6F22-0004-4026-8B6B-C3E73EA18334
Use unleaded premium gasoline with an
octane rating of at least 91 AKI (Anti-Knock
Index) number (Research octane number
96).
VR30DDTT engine model: INFINITI recommends the use of unleaded premium
gasoline with 93 AKI (Anti-Knock Index)
number (Research octane number 98) to
obtain the maximum vehicle performance
and the best driveability.
.
Using a fuel other than that specified
could adversely affect the emission
control system, and may also affect
warranty coverage.
.
Under no circumstances should a leaded
gasoline be used, because this will
damage the three-way catalyst.
.
Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed to
run on E-15 or E-85 fuel. Using E-15 or E85 fuel in a vehicle not specifically
designed for E-15 or E-85 fuel can
adversely affect the emission control
devices and systems of the vehicle.
Damage caused by such fuel is not
covered by the INFINITI new vehicle
limited warranty.
.
Do not use fuel that contains the octane
booster methylcyclopentadienyl manganese tricarbonyl (MMT). Using fuel containing MMT may adversely affect
vehicle performance and vehicle emissions. Not all fuel dispensers are labeled
to indicate MMT content, so you may
have to consult your gasoline retailer for
more details. Note that Federal and
If unleaded premium gasoline is not available, unleaded regular gasoline with an
octane rating of at least 87 AKI number
(Research octane number 91) may be
temporarily used, but only under the
following precautions:
. Have the fuel tank filled only partially
with unleaded regular gasoline, and fill
up with unleaded premium gasoline as
soon as possible.
. Avoid full throttle driving and abrupt
acceleration.
Use unleaded premium gasoline for maximum vehicle performance.
California laws prohibit the use of MMT
in reformulated gasoline.
CAUTION
.
U.S. government regulations require
ethanol dispensing pumps to be identified by a small, square, orange and black
label with the common abbreviation or
the appropriate percentage for that
region.
Gasoline specifications
CV37D1-BC292E95-4B29-40F3-A4C8-1118F7D356C3
INFINITI recommends using gasoline that
meets the World-Wide Fuel Charter (WWFC)
specifications where it is available. Many
of the automobile manufacturers developed this specification to improve emission system and vehicle performance. Ask
your service station manager if the gasoline meets the World-Wide Fuel Charter
(WWFC) specifications.
Reformulated
gasoline
CV37D1-B64B223A-737E-40BE-9877-462F149B1795
Some fuel suppliers are now producing
reformulated gasolines. These gasolines
are specially designed to reduce vehicle
emissions. INFINITI supports efforts towards cleaner air and suggests that you
use reformulated gasoline when available.
10-4 Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(431,1)
Gasoline containing
oxygenates
CV37D1-12B5B588-30F9-476F-9B62-34865892BC31
Some fuel suppliers sell gasoline containing oxygenates such as ethanol, MTBE and
methanol with or without advertising their
presence. INFINITI does not recommend the
use of fuels of which the oxygenate content
and the fuel compatibility for your INFINITI
cannot be readily determined. If in doubt,
ask your service station manager.
If you use oxygenate-blend gasoline,
please take the following precautions as
the usage of such fuels may cause vehicle
performance problems and/or fuel system
damage.
. The fuel should be unleaded and have
an octane rating no lower than that
recommended for unleaded gasoline.
. If an oxygenate-blend, excepting a
methanol blend, is used, it should
contain no more than 10% oxygenate.
(MTBE may, however, be added up to
15%.)
. E-15 fuel contains more than 10%
oxygenate. E-15 fuel will adversely
affect the emission control devices
and systems of the vehicle and should
not be used. Damage caused by such
fuel is not covered by the INFINITI new
vehicle limited warranty.
. If a methanol blend is used, it should
contain no more than 5% methanol
(methyl alcohol, wood alcohol). It
should also contain a suitable amount
of appropriate cosolvents and corrosion inhibitors. If not properly formulated with appropriate cosolvents and
corrosion inhibitors, such methanol
blends may cause fuel system damage
and/or vehicle performance problems.
At this time, sufficient data is not
available to ensure that all methanol
blends are suitable for use in INFINITI
vehicles.
If any undesirable driveability problems
such as engine stalling or hard hot starting
are experienced after using oxygenateblend fuels, immediately change to a nonoxygenate fuel or a fuel with a low blend of
MTBE.
Take care not to spill gasoline during
refueling. Gasoline containing oxygenates
can cause paint damage.
E-15 fuel CV37D1-55AA3E5D-B4B7-4387-A6C1-514DB0C16738
E-15 fuel is a mixture of approximately
15% fuel ethanol and 85% unleaded
gasoline. E-15 can only be used in vehicles
designed to run on E-15 fuel. Do not use E-
15 in your vehicle. U.S. government regulations require fuel ethanol dispensing
pumps to be identified with small, square,
orange and black label with the common
abbreviation or the appropriate percentage
for that region.
E-85 fuel CV37D1-019B5956-3FF3-4BF6-B50B-B0FD9BE1DD27
E-85 fuel is a mixture of approximately
85% fuel ethanol and 15% unleaded
gasoline. E-85 can only be used in a
Flexible Fuel Vehicle (FFV). Do not use E85 fuel in your vehicle. U.S. government
regulations require fuel ethanol dispensing
pumps to be identified by a small, square,
orange and black label with the common
abbreviation or the appropriate percentage
for that region.
Fuel containing
MMT
CV37D1-798C8D68-7496-41DD-BDEC-A7D94D11DA79
MMT, or methylcyclopentadienyl manganese tricarbonyl, is an octane boosting
additive. INFINITI does not recommend the
use of fuel containing MMT. Such fuel may
adversely affect vehicle performance, including the emissions control system. Note
that while some fuel pumps label MMT
content, not all do, so you may have to
consult your gasoline retailer for more
details.
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(432,1)
Aftermarket
fuel additives
CV37D1-0241A1D6-50DD-4735-AB1B-1BF6D3FF4840
INFINITI does not recommend the use of
any aftermarket fuel additives (Example:
fuel injector cleaner, octane booster, intake valve deposit removers, etc.) which
are sold commercially. Many of these
additives intended for gum, varnish or
deposit removal may contain active solvent
or similar ingredients that can be harmful
to the fuel system and engine.
Octane rating
tips
CV37D1-0C94128B-44FC-407D-B5D4-1374AB611F20
or damage to the engine. If any of the
above symptoms are encountered, have
your vehicle checked. It is recommended
you visit an INFINITI retailer for servicing.
However, now and then you may notice
light spark knock for a short time while
accelerating or driving up hills. This is no
cause for concern, because you get the
greatest fuel benefit when there is light
spark knock for a short time under heavy
engine load.
Using unleaded gasoline with an octane
rating lower than recommended above can
cause persistent, heavy spark knock.
(Spark knock is a metallic rapping noise.)
If severe, this can lead to engine damage.
If you detect a persistent heavy spark
knock even when using gasoline of the
stated octane rating, or if you hear steady
spark knock while holding a steady speed
on level roads, it is recommended you have
an INFINITI retailer correct the condition.
Failure to correct the condition is misuse of
the vehicle, for which INFINITI is not
responsible.
Incorrect ignition timing will result in
knocking, after-run or overheating. This in
turn may cause excessive fuel consumption
10-6 Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(433,1)
Oil which may contain foreign matter or
has been previously used should not be
used.
Oil viscosity:
CV37D1-7E511DF7-826F-45D5-B804-CC52F1B085AA
The engine oil viscosity or thickness
changes with temperature. Because of this,
it is important that the engine oil viscosity
be selected based on the temperatures at
which the vehicle will be operated before
the next oil change. Choosing an oil
viscosity other than that recommended
could cause serious engine damage.
JVT0342X
*
2
*
1
API certification mark
API service symbol
ENGINE OIL AND OIL FILTER RECOMMENDATION
CV37D1-D3E5E26B-FC22-4D68-908C-7DA80DA562C9
VR30DDTTCV37D1-73055463-27A6-4BE2-A78C-6725EC81AB92
engine model
Selecting the
correct oil:
CV37D1-C1BBD8C1-CF6B-44E9-90CB-0CC021584CF7
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure
satisfactory engine life and performance,
see “Capacities and recommended fluids/
lubricants” (P.10-2). INFINITI recommends
the use of an energy conserving oil in order
to improve fuel economy.
Select only engine oils that meet the
American Petroleum Institute (API) certification or International Lubricant Standardization and Approval Committee (ILSAC)
certification and SAE viscosity standard.
These oils have the API certification mark
on the front of the container. Oils which do
not have the specified quality label should
not be used as they could cause engine
damage.
Oil additives:
CV37D1-C6150E87-6F96-4318-8F1A-85D798E9B0DF
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used
and maintenance intervals are followed.
Selecting the
correct oil filter:
CV37D1-A18AF9A6-E383-4277-8DC6-3551FA05B33C
Your new vehicle is equipped with a highquality genuine NISSAN oil filter. When
replacing, use the genuine oil filter or its
equivalent for the reason described in
change intervals.
Change intervals:
CV37D1-6BBF04C8-7568-41CF-8D44-1A84C0ED6100
The oil and oil filter change intervals for
your engine are based on the use of the
specified quality oils and filters. Oil and
filter other than the specified quality, or oil
and filter change intervals longer than
recommended could reduce engine life.
Damage to engines caused by improper
maintenance or use of incorrect oil and
filter quality and/or viscosity is not covered
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-7
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(434,1)
by the new INFINITI vehicle limited warranties.
has been previously used should not be
used.
Your engine was filled with a high quality
engine oil when it was built. You do not
have to change the oil before the first
recommended change interval. Oil and
filter change intervals depend upon how
you use your vehicle.
Oil viscosity:CV37D1-5345E421-706A-459A-8727-3A90EE1785F0
The engine oil viscosity or thickness
changes with temperature. Because of this,
it is important that the engine oil viscosity
be selected based on the temperatures at
which the vehicle will be operated before
the next oil change. Choosing an oil
viscosity other than that recommended
could cause serious engine damage.
2.0L turboCV37D1-059AC215-00F8-4DB1-A4C3-7193356A55D4
gasoline engine model
Selecting the
correct oil:
CV37D1-6C2B7CCC-D3C1-4D6F-B3BC-4C0190938B53
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure
satisfactory engine life and performance,
see “Capacities and recommended fluids/
lubricants” (P.10-2).
Select only engine oils that meet the
MB229.5 and SAE viscosity standard.
These oils have the MB229.5 on the
container. Oils which do not have the
specified quality label should not be used
as they could cause engine damage.
JVT0428X
Selecting the
correct oil filter:
CV37D1-7BA31F4F-975E-47A2-B844-171A0ED491DC
Your new vehicle is equipped with a highquality genuine NISSAN oil filter. When
replacing, use the genuine oil filter or its
equivalent for the reason described in
change intervals.
Oil additives:
CV37D1-91FB3B9D-7752-442A-B3D2-042B2C1AE68E
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used
and maintenance intervals are followed.
Oil which may contain foreign matter or
10-8 Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(435,1)
Change intervals:
CV37D1-E1676489-2050-416D-A28D-8CFCFB058E45
The oil and oil filter change intervals for
your engine are based on the use of the
specified quality oils and filters. Oil and
filter other than the specified quality, or oil
and filter change intervals longer than
recommended could reduce engine life.
Damage to engines caused by improper
maintenance or use of incorrect oil and
filter quality and/or viscosity is not covered
by the new INFINITI vehicle limited warranties.
Your engine was filled with a high quality
engine oil when it was built. You do not
have to change the oil before the first
recommended change interval.
AIR CONDITIONING SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS
CV37D1-CDCFAB3E-830C-4475-8A79-A638F5620A17
The air conditioning system in your
INFINITI vehicle must be charged with the
refrigerant HFC-134a (R-134a) and the
lubricant, NISSAN A/C system oil PAG or
the exact equivalents.
CAUTION
The use of any other refrigerant or lubricant
may cause severe damage to the air
conditioning system and may require the
replacement of all air conditioner system
components.
The refrigerant HFC-134a (R-134a) in your
INFINITI vehicle will not harm the earth’s
ozone layer. Although this refrigerant does
not affect the earth’s atmosphere, certain
governmental regulations require the recovery and recycling of any refrigerant
during automotive air conditioning system
service. Your INFINITI retailer has the
trained technicians and equipment needed
to recover and recycle your air conditioning
system refrigerant.
It is recommended you visit an INFINITI
retailer when servicing your air conditioning system.
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-9
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(436,1)
SPECIFICATIONS
CV37D1-C4047CDF-FC90-4B6A-B3AD-46BBE7E650C5
ENGINE
CV37D1-27E56DF3-4A90-4674-8571-79AA70F61975
Model
VR30DDTT
2.0L turbo gasoline engine
Type
Gasoline, 4-cycle
6-cylinder, V-slanted at 608
3.3866 3.386
(86.0 6 86.0)
182.88 (2,997)
1-2-3-4-5-6
Gasoline, 4-cycle, DOHC
4-cylinder, in-line
3.268 6 3.622
(83.0 6 92.0)
121.49 (1,991 )
1-3-4-2
Cylinder arrangement
Bore 6 Stroke
in (mm)
Displacement
Firing order
cu in (cm3)
Idle speed
Ignition timing
(B.T.D.C.)
rpm
Spark plug
Spark plug gap
(Normal)
Camshaft operation
No adjustment is necessary.
degree/rpm
in (mm)
DILKAR8K8G
SILZKFR8E7S
0.031 (0.8)
0.028 (0.7)
Timing chain
Timing chain
STI0425
VR30DDTT engine
This spark ignition system complies with the Canadian standard ICES-002.
10-10
Condition:
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(437,1)
** Click HERE to see "Owner's Manual Supplement" **
WHEELS AND
TIRES
CV37D1-F8E5243C-624C-49E0-9FDB-368F2FA574BD
DIMENSIONS
CV37D1-A185873C-C0C6-4C9E-AA39-E2530E5FAEB4
in (mm)
Road wheel
CV37D1-C54AC2ED-6038-4F80-B970-C73EF54C02D3
Type
Overall length
184.4 (4,685)
Overall width
72.8 (1,850)
Overall height
54.9 (1,395)
54.5 (1,385)*1
Size
Offset in (mm)
196 9J
1.57 (40)
Conventional
206 9J
206 9.5J
1.57 (40)
1.85 (47)
Front tread
61.2 (1,555)
Spare (if so equipped)
18 6 4T
0 (0)
Rear tread
62.2 (1,580)
61.8 (1,565)*2
Wheelbase
112.2 (2,850)
Tire
CV37D1-C8AE7FFD-2C12-4C71-A3F3-F78E4E149780
Type
Conventional
Size
Pressure PSI (kPa) [Cold]
P255/40RF19 96V
P255/35RF20 97V XL
35 (240)
255/35RF20 97Y XL
Front: 255/35RF20 97Y XL
Rear: 275/30RF20 97Y XL
Spare (T-type) (if so equipped)
T145/70R18 107M
*1: Two-Wheel Drive (2WD) models with
VR30DDTT engine
*2: 275/30RF20 tire models
38 (260)
60 (420)
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-11
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(438,1)
WHEN TRAVELING OR REGISTERING IN
ANOTHER COUNTRY
CV37D1-A1581DBE-C0B0-4F11-9293-2CC17BDE9887
If you plan to travel in another country, you
should first find out if the fuel available is
suitable for your vehicle’s engine.
VEHICLE IDENTIFICATION
CV37D1-12CB0BB9-8EF0-442E-82A4-5DB634EF5D6E
Using fuel with too low an octane rating
may cause engine damage. All gasoline
vehicles must be operated with unleaded
gasoline. Therefore, avoid taking your
vehicle to areas where appropriate fuel is
not available.
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify
the vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications
may differ.
When any vehicle is to be taken into
another country, state, province or district
and registered, its modifications, transportation, and registration are the responsibility of the user. INFINITI is not
responsible for any inconvenience that
may result.
10-12
Condition:
STI0716
VEHICLE IDENTIFICATION NUMBER
(VIN) PLATE
CV37D1-6860C560-CCF6-4161-BB17-92D8646B01F7
The vehicle identification number plate is
attached as shown. This number is the
identification for your vehicle and is used
in the vehicle registration.
STI0717
VEHICLE IDENTIFICATION NUMBER
(chassis number)
CV37D1-DCB7F909-8300-4B8A-BD88-108D68C70BB5
The number is stamped as shown in the
engine compartment.
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(439,1)
ENGINE SERIAL
NUMBER
CV37D1-07F78586-6CB6-40F9-87AE-7FE1781DFBE7
The number is stamped on the engine as
shown.
STI0509
STI0707
VR30DDTT engine
F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL
CV37D1-A385459D-29DC-47A1-A8F1-439044C67AB6
The Federal/Canadian Motor Vehicle Safety
Standards (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown. This label
contains valuable vehicle information,
such as: Gross Vehicle Weight Ratings
(GVWR), Gross Axle Weight Rating (GAWR),
month and year of manufacture, Vehicle
Identification Number (VIN), etc. Review it
carefully.
JVT0288X
2.0L turbo gasoline engine
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-13
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(440,1)
STI0719
EMISSION CONTROL INFORMATION
LABEL
CV37D1-F64574D3-736A-4497-9959-97B625F00A64
The emission control information label is
attached as shown.
10-14
Condition:
JVT0456X
TIRE AND LOADING INFORMATION
LABEL CV37D1-DC898DE9-943C-46BC-B7B8-63A84B1E77EF
The cold tire pressure is shown on the Tire
and Loading Information label affixed to
the pillar as illustrated.
STI0721
AIR CONDITIONER SPECIFICATION
LABEL CV37D1-CC83DA48-0EA9-4C3B-85BD-6799F5CB0094
The air conditioner specification label is
attached as shown.
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(441,1)
INSTALLING FRONT LICENSE PLATE
REMOVING AIR DEFLECTORS
CV37D1-1683BD89-41A7-4F6C-B8FB-A0E68AF2C426
CV37D1-555618E2-7242-401A-AA8C-3DE6E17EB1BC
.
.
.
1.
License plate bracket
J-nut 6 2
Screw 6 2
Park the vehicle on flat, level ground.
2. Locate the two dimples
grille.
3. Insert J-nuts
bracket.
B
*
A in the front
*
into the license plate
4. Insert the bosses of the license plate
bracket into the front grille, aligning the
C with the location marks (two
holes *
A .
dimples) *
5. Install the license plate bracket with
D provided.
the screws *
6. Install the license plate with bolts that
are no longer than 0.55 in (14 mm).
JVT0455X
Left side
This vehicle is equipped with air deflectors
in front of the front wheels. The deflectors
will change the air flow to help improve
aerodynamic performance.
When transporting your vehicle on a trailer,
the air deflectors may interfere with a
steep slope to a trailer bed. In this case,
remove the deflectors from the vehicle.
JVT0450X
Use the following steps to mount the
license plate.
Only use the recommended mounting
position, otherwise the radar sensor (Intelligent Cruise Control (ICC) system) (if so
equipped) obstruction may result.
1. Loosen four screws as shown and
A .
remove the left-side air deflector *
2. Tighten the removed screw
original position.
Before mounting the license plate, confirm
that the following parts are enclosed in the
plastic bag.
B
*
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
in its
10-15
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(442,1)
VEHICLE LOADING INFORMATION
CV37D1-8B53E02A-80CF-4A3B-9FE9-553395918904
Tightening torque:
4 to 6 ft-lb
(5.6 to 8.4 N·m)
3. Perform the same procedure to remove
the right-side air deflector.
4. Store the two air deflectors and six
screws to reinstall in the reverse order.
5. When reinstalling, make sure all eight
screws are firmly tightened on both air
deflectors.
Tightening torque:
4 to 6 ft-lb
(5.6 to 8.4 N·m)
WARNING
It is extremely dangerous to
ride in a cargo area inside the
vehicle. In a collision, people
riding in these areas are more
likely to be seriously injured
or killed.
. Do not allow people to ride in
any area of vehicle that is not
equipped with seats and seat
belts.
. Be sure everyone in your
vehicle is in a seat and using
a seat belt properly.
.
TERMS CV37D1-78B8C1B5-1A34-4ED5-8630-67E81CC88168
It is important to familiarize yourself
with the following terms before
loading your vehicle:
. Curb Weight (actual weight of your
vehicle) - vehicle weight including: standard and optional equipment, fluids, emergency tools,
10-16
Condition:
.
.
.
.
.
and spare tire assembly. This
weight does not include passengers and cargo.
GVW (Gross Vehicle Weight) - curb
weight plus the combined weight
of passengers and cargo.
GVWR (Gross Vehicle Weight Rating) - maximum total combined
weight of the unloaded vehicle,
passengers, luggage, hitch, trailer
tongue load and any other optional equipment. This information is located on the F.M.V.S.S./C.
M.V.S.S. label.
GAWR (Gross Axle Weight Rating) maximum weight (load) limit specified for the front or rear axle.
This information is located on the
F.M.V.S.S./C.M.V.S.S. label.
GCWR (Gross Combined Weight
Rating) - The maximum total
weight rating of the vehicle, passengers, cargo, and trailer.
Vehicle Capacity Weight, Load
limit, Total load capacity - max-
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(443,1)
imum total weight limit specified
of the load (passengers and cargo) for the vehicle. This is the
maximum combined weight of
occupants and cargo that can be
loaded into the vehicle. If the
vehicle is used to tow a trailer,
the trailer tongue weight must be
included as part of the cargo load.
This information is located on the
Tire and Loading Information label.
. Cargo capacity - permissible
weight of cargo, the weight of
total occupants weight subtracted
from the load limit.
STI0365
VEHICLE LOAD
CAPACITY
CV37D1-5B6F8ADA-8C58-456E-9BB0-D4AE18351679
Do not exceed the load limit of your
vehicle shown as “The combined
weight of occupants and cargo” on
the Tire and Loading Information
label. Do not exceed the number of
occupants shown as “Seating Capacity” on the Tire and Loading Information label.
To get “the combined weight of
occupants and cargo”, add the
weight of all occupants, then add
the total luggage weight. Examples
are shown in the illustration.
Steps for determining correct load
limit
CV37D1-435A873C-FE5D-432A-8D43-CF7CBF00D87A
1. Locate the statement “The combined weight of occupants and
cargo should never exceed XXX kg
or XXX lbs” on your vehicle’s
placard.
2. Determine the combined weight
of the driver and passengers that
will be riding in your vehicle.
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-17
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(444,1)
3. Subtract the combined weight of
the driver and passengers from
XXX kg or XXX lbs.
4. The resulting figure equals the
available amount of cargo and
luggage load capacity. For example, if the XXX amount equals
1400 lbs. and there will be five
150 lb. passengers in your vehicle, the amount of available cargo
and luggage load capacity is 650
lbs. (1400 − 750 (5 x 150) = 650
lbs or 640 − 340 (5 x 70) = 300
kg.)
5. Determine the combined weight
of luggage and cargo being
loaded on the vehicle. That weight
may not safely exceed the available cargo and luggage load
capacity calculated in Step 4.
6. If your vehicle will be towing a
trailer, load from your trailer will
be transferred to your vehicle.
Consult this manual to determine
how this reduces the available
10-18
Condition:
cargo and luggage load capacity
of your vehicle.
Before driving a loaded vehicle,
confirm that you do not exceed the
Gross Vehicle Weight Rating (GVWR)
or the Gross Axle Weight Rating
(GAWR) for your vehicle. (See “Measurement of weights” (P.10-19).)
Also check tires for proper inflation
pressures. See the Tire and Loading
Information label.
LOADING CV37D1-367C9547-B8F4-40A5-BCE4-39C37DBD2B67
TIPS
. The GVW must not exceed GVWR
or GAWR as specified on the F.M.V.
S.S./C.M.V.S.S. certification label.
. Do not load the front and rear axle
to the GAWR. Doing so will exceed
the GVWR.
WARNING
.
Properly secure all cargo to
help prevent it from sliding or
shifting. Do not place cargo
higher than the seatbacks. In
a sudden stop or collision,
unsecured cargo could cause
personal injury.
. Do not load your vehicle any
heavier than the GVWR or the
maximum front and rear
GAWRs. If you do, parts of
your vehicle can break, tire
damage could occur, or it can
change the way your vehicle
handles. This could result in
loss of control and cause
personal injury.
. Overloading could not only
shorten the life of your vehicle and the tires, but also
could lead to hazardous vehicle handling and long braking
distance. This may cause a
premature tire malfunction,
which could result in a serious
accident and personal injury.
Failures caused by overloading are not covered by the
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(445,1)
TOWING A TRAILER
CV37D1-D0235718-BCC7-46F6-99A2-4F6CF7CB5A97
vehicle’s warranty.
MEASUREMENT
OF WEIGHTS
CV37D1-626A0DEF-CEAF-4B2B-B914-1CD2D9E7382E
Secure loose items to prevent weight
shifts that could affect the balance of
your vehicle. When the vehicle is
loaded, drive to a scale and weigh
the front and the rear wheels separately to determine axle loads. Individual axle loads should not
exceed either of the gross axle
weight ratings (GAWR). The total of
the axle loads should not exceed the
gross vehicle weight rating (GVWR).
These ratings are given on the
vehicle certification label. If weight
ratings are exceeded, move or remove items to bring all weights
below the ratings.
Do not tow a trailer with your
vehicle.
FLAT TOWING
CV37D1-4BE369F8-85AF-4E5B-BCE0-25BA91776960
Towing your vehicle with all four wheels on
the ground is sometimes called flat towing.
This method is sometimes used when
towing a vehicle behind a recreational
vehicle, such as a motor home.
CAUTION
.
Failure to follow these guidelines can
result in severe transmission damage.
.
Whenever flat towing your vehicle, always tow forward, never backward.
.
DO NOT tow any Automatic Transmission
(AT) vehicle with all four wheels on the
ground (flat towing). Doing so WILL
DAMAGE internal transmission parts
due to lack of transmission lubrication.
.
DO NOT tow any All-Wheel Drive (AWD)
vehicle with any of the wheels on the
ground. Doing so may cause serious and
expensive damage to the powertrain.
.
For emergency towing procedures refer
to “Towing recommended by INFINITI”
(P.6-18).
AutomaticCV37D1-91431205-A8B6-4757-8B7E-FE93E672CD0D
Transmission
All-Wheel Drive
(AWD) models:
CV37D1-28A226BA-EAC5-4B64-BB46-D6CD8A65285A
Do not tow an AWD vehicle with any of the
wheels on the ground.
Two-Wheel CV37D1-E30D05C1-1748-4EAF-BC02-14FEFA9D517B
Drive (2WD) models:
To tow a vehicle equipped with an automatic transmission, an appropriate vehicle
dolly MUST be placed under the towed
vehicle’s drive wheels. Always follow the
dolly manufacturer’s recommendations
when using their product.
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-19
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(446,1)
UNIFORM TIRE QUALITY GRADING
CV37D1-BE355711-C850-4467-8C72-25BED609009F
DOT (Department Of Transportation) Quality Grades: All passenger car tires must
conform to federal safety requirements in
addition to these grades.
Quality grades can be found where applicable on the tire sidewall between tread
shoulder and maximum section width. For
example:
Treadwear 200 Traction AA Temperature A
TREADWEAR
CV37D1-06C0EFD4-1C2A-4B83-84AD-0520C1DA8585
The treadwear grade is a comparative
rating based on the wear rate of the tire
when tested under controlled conditions
on a specified government test course. For
example, a tire graded 150 would wear one
and one-half (1 1/2) times as well on the
government course as a tire graded 100.
The relative performance of tires depends
upon actual conditions of their use, however, and may depart significantly from the
norm due to variations in driving habits,
service practices and differences in road
characteristics and climate.
10-20
Condition:
TRACTIONCV37D1-5CED13CD-47A5-4914-A469-E7A48CECA48B
AA, A, B AND C
The traction grades, from highest to lowest, are AA, A, B and C. Those grades
represent the tire’s ability to stop on wet
pavement as measured under controlled
conditions on specified government test
surfaces of asphalt and concrete. A tire
marked C may have poor traction performance.
WARNING
The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration,
cornering, hydroplaning, or peak traction
characteristics.
tire failure. The grade C corresponds to a
level of performance which all passenger
car tires must meet under the Federal
Motor Vehicle Safety Standard No. 109.
Grades B and A represent higher levels of
performance on the laboratory test wheel
than the minimum required by law.
WARNING
The temperature grade for this tire is
established for a tire that is properly
inflated and not overloaded. Excessive
speed, under-inflation, or excessive loading,
either separately or in combination, can
cause heat build-up and possible tire failure.
TEMPERATURE
A, B AND C
CV37D1-76F4F130-CFBB-4D14-A56A-6BF438170741
The temperature grades A (the highest), B,
and C, representing the tire’s resistance to
the generation of heat and its ability to
dissipate heat when tested under controlled conditions on a specified indoor
laboratory test wheel. Sustained high
temperature can cause the material of the
tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(447,1)
EMISSION CONTROL SYSTEM WARRANTY
REPORTING SAFETY DEFECTS
CV37D1-F953CF91-03CF-4572-8D77-CBF6868C94E6
CV37D1-060D9A6F-47CD-4EEF-8BA5-0685009D0AD1
Your INFINITI is covered by the following
emission warranties.
For USA
If you believe that your vehicle has a
defect which could cause a crash or
could cause injury or death, you
should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to
notifying INFINITI.
If NHTSA receives similar complaints,
it may open an investigation, and if it
finds that a safety defect exists in a
group of vehicles, it may order a
recall and remedy campaign. However, NHTSA cannot become involved
in individual problems between you,
your retailer, or INFINITI.
To contact NHTSA, you may call the
Vehicle Safety Hotline toll-free at 1888-327-4236 (TTY: 1-800-4249153); go to http://www.safercar.
gov; or write to: Administrator,
NHTSA, 400 Seventh Street, SW.,
Washington DC 20590. You can also
obtain other information about motor
vehicle safety from http://www.safe-
For USA:
. Emission Defects Warranty
. Emissions Performance Warranty
Details of these warranties may be found
with other vehicle warranties in your
Warranty Information Booklet that comes
with your INFINITI. If you did not receive a
Warranty Information Booklet, or it has
become lost, you may obtain a replacement by writing to:
. Nissan Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario,
L4W 4Z5
. INFINITI Division
Nissan North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003
For Canada:
Emission Control System Warranty
Details of these warranties may be found
with other vehicle warranties in your
Warranty and Roadside Assistance Information that comes with your INFINITI. If you
did not receive a Warranty and Roadside
Assistance Information, or it has become
lost, you may obtain a replacement by
writing to:
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-21
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(448,1)
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US only)
CV37D1-1566689B-E555-4824-98F9-8466E02C8EE3
rcar. gov.
You may notify INFINITI by contacting
our Consumer Affairs Department,
toll-free, at 1-800-662-6200.
For Canada
If you believe that your vehicle has a
defect which could cause a crash or
could cause injury or death, you
should immediately inform Transport
Canada in addition to notifying
INFINITI.
If Transport Canada receives complaints, it may open an investigation,
and if it finds that a safety defect
exists in a group of vehicles, it may
request that INFINITI conduct a recall
campaign. However, Transport Canada cannot become involved in individual problems between you, your
retailer, or INFINITI.
You may contact Transport Canada’s
Defect Investigations and Recalls
Division toll free at 1-800-3330510. You may also report safety
10-22
Condition:
defects online at:
https://wwwapps.tc.gc.ca/Saf-SecSur/7/PCDB-BDPP/Index.aspx.
Additional information concerning
motor vehicle safety may be obtained
from Transport Canada’s Road Safety
Information Centre at 1-800-3330371 or online at www.tc.gc.ca/
roadsafety (English speakers) or
www.tc.gc.ca/securiteroutiere
(French speakers).
To notify INFINITI of any safety concerns please contact our Consumer
Information Centre toll free at 1-800361-4792.
WARNING
A vehicle equipped with Intelligent AllWheel Drive (AWD) should never be tested
using a two wheel dynamometer (such as
the dynamometers used by some states for
emissions testing), or similar equipment.
Make sure you inform test facility personnel
that your vehicle is equipped with AWD
before it is placed on a dynamometer. Using
the wrong test equipment may result in
transmission damage or unexpected vehicle
movement which could result in serious
vehicle damage or personal injury.
Due to legal requirements in some states/
areas, your vehicle may be required to be
in what is called the “ready condition” for
an Inspection/Maintenance (I/M) test of
the emission control system.
The vehicle is set to the “ready condition”
when it is driven through certain driving
patterns. Usually, the “ready condition”
can be obtained by ordinary usage of the
vehicle.
If a powertrain system component is
repaired or the battery is disconnected,
the vehicle may be reset to a “not ready
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(449,1)
EVENT DATA RECORDERS (EDR)
CV37D1-BC64BE2A-EB25-4897-82DE-302B00964F20
condition”. Before taking the I/M test,
check the vehicle’s inspection/maintenance test readiness condition. Place the
ignition switch in the ON position without
starting the engine. If the Malfunction
Indicator Light (MIL) comes on steady for
20 seconds and then blinks for 10 seconds, the I/M test condition is “not ready”.
If the MIL does not blink after 20 seconds,
the I/M test condition is “ready”.
It is recommended you visit an INFINITI
retailer to set the “ready condition” or to
prepare the vehicle for testing.
This vehicle is equipped with an Event Data
Recorder (EDR). The main purpose of an
EDR is to record, in certain crash or near
crash-like situations, such as an air bag
deployment or hitting a road obstacle, data
that will assist in understanding how a
vehicle’s systems performed. The EDR is
designed to record data related to vehicle
dynamics and safety systems for a short
period of time, typically 30 seconds or less.
The EDR in this vehicle is designed to
record such data as:
. How various systems in your vehicle
were operating;
. Whether or not the driver and passenger safety belts were buckled/fastened;
. How far (if at all) the driver was
depressing the accelerator and/or
brake pedal; and,
. How fast the vehicle was traveling.
. Sounds are not recorded.
These data can help provide a better
understanding of the circumstances in
which crashes and injuries occur.
crash location) are recorded. However,
other parties, such as law enforcement,
could combine the EDR data with the type
of personally identifying data routinely
acquired during a crash investigation.
To read data recorded by an EDR, special
equipment is required and access to the
vehicle or the EDR is needed. In addition to
the vehicle manufacturer and INFINITI
retailer, other parties, such as law enforcement, that have the special equipment, can
read the information if they have access to
the vehicle or the EDR. EDR data will only
be accessed with the consent of the vehicle
owner or lessee or as otherwise required or
permitted by law.
NOTE: EDR data are recorded by your
vehicle only if a nontrivial crash situation
occurs; no data are recorded by the EDR
under normal driving conditions and no
personal data (e.g. name, gender, age and
Technical and consumer information
Condition:
[ Edit: 2016/ 4/ 27
10-23
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(450,1)
OWNER’S MANUAL/SERVICE MANUAL
ORDER INFORMATION
CV37D1-286B764D-AFDB-4EF1-A188-EB0EDBD40366
Genuine INFINITI Service Manual for this
model year and prior can be purchased. A
genuine INFINITI Service Manual is the best
source of service and repair information for
your vehicle. This manual is the same one
used by the factory-trained technicians
working at INFINITI retailers. Genuine
INFINITI Owner’s Manuals can also be
purchased.
For USA:
For current pricing and availability of
genuine INFINITI Service Manuals, contact:
1-800-450-9491
www.infiniti-techinfo.com
For current pricing and availability of
genuine INFINITI Owner’s Manuals, contact:
1-800-247-5321
For Canada:
To purchase a copy of a genuine INFINITI
Service Manual or Owner’s Manual for this
model year and prior, contact an INFINITI
retailer. For the phone number and location
of an INFINITI retailer in your area call the
INFINITI Satisfaction Center at 1-800-3614792 and a bilingual INFINITI representative will assist you.
10-24
Condition:
Technical and consumer information
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(453,1)
11 Index
A
ABS (Anti-lock Braking System) ......................
...
5-134
Active Lane Control ..........................................
...
5-27
Active noise cancellation ................................
...
5-148
Active sound enhancement .............................
...
5-148
Active trace control ........................................
...
5-138
Air bag system
Front-seat mounted side-impact
supplemental air bag system .....................
...
1-55
Roof-mounted curtain side-impact and
rollover supplemental air bag system .........
...
1-55
Air bag warning labels .....................................
...
1-57
Air bag warning light ...............................
...
1-58, 2-17
Air cleaner housing filter ..................................
...
8-22
Air conditioner
Air conditioner specification label ............
...
10-14
Air conditioning system refrigerant and
lubricant recommendations ........................
...
10-9
Air deflectors .................................................
...
10-15
Alarm
How to stop alarm (see vehicle
security system) .........................................
...
2-36
Alcohol, drugs and driving ................................
...
5-11
Antenna .............................................................
...
4-3
Anti-lock Braking System (ABS) ......................
...
5-134
Appearance care
Exterior appearance care ...............................
...
7-2
Interior appearance care ..............................
...
7-5
Audible reminders ............................................
...
2-20
Condition:
Autolight system ..............................................
...
2-41
Automatic
Automatic adjusting function
(power windows) ........................................
...
2-57
Automatic Transmission Fluid (ATF) .............
...
8-14
Driving with Automatic Transmission (AT) ... 5-16
Automatic door locks ..........................................
...
3-6
Automatic drive positioner ................................
...
3-33
Automatic seat positioner .................................
...
3-33
Auxiliary battery ...............................................
...
6-14
Average speed .................................................
...
2-31
Avoiding collision and rollover ...........................
...
5-9
B
Back-up Collision Intervention (BCI) ..................
...
5-63
Battery .............................................................
...
8-17
Auxiliary battery .........................................
...
6-14
Battery replacement, Intelligent Key ..............
...
3-2
Battery saver system ..................................
...
2-44
Intelligent Key ............................................
...
8-28
Variable voltage control system ..................
...
8-20
Before starting the engine ................................
...
5-15
Belts (See drive belts) ......................................
...
8-20
Blind Spot Intervention® (BSI) ..........................
...
5-50
Blind Spot Warning (BSW) ................................
...
5-42
Brake
Anti-lock Braking System (ABS) .................
...
5-134
Brake fluid .................................................
...
8-15
Brake force distribution .............................
...
5-137
[ Edit: 2016/ 4/ 27
Brake system ............................................
...
5-133
Parking brake operation ..............................
...
5-22
Brake warning light ..........................................
...
2-13
Break-in schedule ..........................................
...
5-125
Bulb check/instrument panel ............................
...
2-12
Bulb replacement .............................................
...
8-30
C
Capacities and
recommended fluids/lubricants ........................
...
10-2
Car phone or CB radio ........................................
...
4-3
Card holder ......................................................
...
2-53
Catalytic converter
Three-way catalyst .......................................
...
5-5
Changing intercooler coolant ............................
...
8-10
Chassis and body maintenance ........................
...
9-14
Chassis control ..............................................
...
5-140
Check tire pressure warning .............................
...
2-25
Checking intercooler coolant level ....................
...
8-10
Child restraints ................................................
...
1-21
LATCH system .............................................
...
1-23
Precautions on child restraints ...................
...
1-21
Child safety ......................................................
...
1-18
Chimes
Audible reminders ......................................
...
2-20
Seat belt warning light and chime ..............
...
2-17
Circuit breaker
Fusible link ................................................
...
8-26
Cleaning exterior and interior ......................
...
7-2, 7-5
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(454,1)
Clock ...............................................................
...
2-34
Coat hooks .......................................................
...
2-54
Cockpit ...............................................................
...
2-3
Cold weather driving ......................................
...
5-145
Compact spare tire ...........................................
...
8-46
Compass ............................................................
...
2-9
Console box .....................................................
...
2-53
Coolant
Capacities and
recommended fluids/lubricants ..................
...
10-2
Changing engine coolant .......................
...
8-7, 8-9
Checking engine coolant level ...............
...
8-7, 8-8
Corrosion protection ...........................................
...
7-8
Courtesy light ...................................................
...
2-62
Cruise control ...................................................
...
5-74
Fixed speed cruise control (on ICC system) ...
... 5-92
Intelligent Cruise Control (ICC) .....................
...
5-76
Cruise indicator ................................................
...
2-27
Cup holders .....................................................
...
2-51
Current fuel consumption .................................
...
2-32
D
Daytime running light system ...........................
...
2-44
Defroster switch
Rear window and outside mirror
defroster switch .........................................
...
2-40
Dimensions ....................................................
...
10-11
Direct Adaptive Steering .................................
...
5-131
Distance Control Assist (DCA) ...........................
...
5-96
Distance to empty ............................................
...
2-31
Drive belts .......................................................
...
8-20
Drive positioner ................................................
...
3-33
Driver assist system indicator ...........................
...
2-27
Driving
Cold weather driving .................................
...
5-145
Driving with Automatic Transmission (AT) ... 5-16
Precautions when starting and driving ..........
...
5-4
E
ECO drive indicator light ...................................
...
2-18
ECO mode ........................................................
...
5-24
ECO pedal system ............................................
...
5-24
Economy
Fuel ...........................................................
...
5-126
Elapsed time ....................................................
...
2-31
Elapsed time and trip odometer .......................
...
2-31
Emission control information label .................
...
10-14
Emission control system maintenance ................
...
9-9
Emission control system warranty ..................
...
10-21
Engine
Before starting the engine ..........................
...
5-15
Break-in schedule .....................................
...
5-125
Capacities and
recommended fluids/lubricants ..................
...
10-2
Changing engine coolant .......................
...
8-7, 8-9
Changing engine oil and filter ....................
...
8-11
Checking engine coolant level ...............
...
8-7, 8-8
Checking engine oil level ............................
...
8-11
Coolant temperature gauge ..........................
...
2-8
Emergency engine shut off .........................
...
5-14
Engine block heater ...................................
...
5-146
Engine compartment check locations ............
...
8-4
Engine cooling system (2.0L turbo gasoline
engine models) ............................................
...
8-8
Engine cooling system (VR30DDTT
engine models) ............................................
...
8-6
Engine oil ...................................................
...
8-10
Engine oil and filter replacement indicator ...
... 2-28
Engine oil and oil filter recommendation ....
... 10-7
Engine serial number ...............................
...
10-13
Engine specifications ...............................
...
10-10
Engine start operation indicator .................
...
2-24
If your vehicle overheats ............................
...
6-16
Intercooler cooling system ...........................
...
8-9
Remote engine start ....................................
...
3-20
Remote engine start operation indicator .....
... 2-24
Starting the engine ....................................
...
5-15
Engine coolant temperature gauge .....................
...
2-8
Event Data Recorders (EDR) ............................
...
10-23
Exhaust gas (carbon monoxide) ..........................
...
5-4
Explanation of scheduled maintenance items .....
... 9-5
F
F.M.V.S.S./C.M.V.S.S. certification label ...........
...
10-13
Filter
Air cleaner housing filter ............................
...
8-22
Changing engine oil and filter ....................
...
8-11
Flashers (See hazard warning flasher switch) .....
... 6-2
Flat tire ..............................................................
...
6-3
Flat Tire - Visit dealer warning ..........................
...
2-25
Flat towing .....................................................
...
10-19
Floor mat cleaning ..............................................
...
7-6
Floor mat installation .........................................
...
7-6
11-2
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(455,1)
Fluid
Automatic Transmission Fluid (ATF) .............
...
8-14
Brake fluid .................................................
...
8-15
Capacities and
recommended fluids/lubricants ..................
...
10-2
Engine coolant (2.0L turbo gasoline
engine models) ............................................
...
8-8
Engine coolant (VR30DDTT engine models) ... 8-6
Engine oil ...................................................
...
8-10
Intercooler coolant .......................................
...
8-9
Power steering fluid ...................................
...
8-14
Window washer fluid ..................................
...
8-16
Fog light switch ................................................
...
2-47
Forward Emergency Braking (FEB) system .......
...
5-107
Forward Emergency Braking (FEB) system
warning light ....................................................
...
2-14
Front passenger air bag and status light ..........
...
1-48
Front power seat adjustment ..............................
...
1-3
Front seat
Front seat adjustment ..................................
...
1-3
Fuel
Capacities and
recommended fluids/lubricants ..................
...
10-2
Fuel economy ............................................
...
5-126
Fuel information .........................................
...
10-4
Fuel octane rating ......................................
...
10-4
Fuel-filler cap ..............................................
...
3-26
Fuel-filler door .............................................
...
3-26
Gauge ..........................................................
...
2-9
Fuel Efficient Driving Tips ...............................
...
5-125
Fuses ...............................................................
...
8-25
Fusible links .....................................................
...
8-26
G
Garage door opener
HomeLink® Universal Transceiver ...............
...
2-62
Gas cap ............................................................
...
3-26
Gauge ................................................................
...
2-6
Engine coolant temperature gauge ...............
...
2-8
Fuel gauge ...................................................
...
2-9
Odometer .....................................................
...
2-7
Speedometer ................................................
...
2-7
Tachometer ..................................................
...
2-8
Trip computer .............................................
...
2-31
General maintenance .........................................
...
9-2
Glove box .........................................................
...
2-53
H
Hazard warning flasher switch ............................
...
6-2
Head restraints/headrests ..................................
...
1-8
Headlights
Aiming control (See Adaptive Front lighting
System (AFS)) .............................................
...
2-45
Headlight switch ........................................
...
2-40
Heated seats ....................................................
...
2-48
Heated steering wheel ......................................
...
2-49
Heater
Engine block heater ...................................
...
5-146
High beam assist .............................................
...
2-42
Hill start assist system ...................................
...
5-139
...
2-62
HomeLink® Universal Transceiver .....................
Hood release ....................................................
...
3-23
Hook
Coat hooks .................................................
...
2-54
Trunk hooks ...............................................
...
2-54
Horn .................................................................
...
2-47
Hydraulic pump electric power steering ..........
...
5-131
I
Idling Stop System .........................................
...
5-140
Idling Stop System indicator light ....................
...
2-19
Idling Stop System reminder buzzer .................
...
2-21
Ignition switch
(Push-button) .............................................
...
5-12
Immobilizer system ..........................................
...
2-36
Indicator
Lights .........................................................
...
2-18
Vehicle information display ........................
...
2-21
Indicator lights .................................................
...
2-18
Indicators for operation (vehicle
information display) .........................................
...
2-24
INFINITI Drive Mode Selector ............................
...
5-23
Infiniti InTouch Owner’s Manual .........................
...
4-2
INFINITI Vehicle Immobilizer System .................
...
2-36
Engine start ...............................................
...
2-36
Inside mirror ....................................................
...
3-30
Inspection/maintenance (I/M) test ..................
...
10-22
Instrument brightness control ..........................
...
2-46
Instrument panel ................................................
...
2-5
Intelligent All-Wheel Drive (AWD) ....................
...
5-127
Intelligent Cruise Control (ICC) ..........................
...
5-76
11-3
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(456,1)
Intelligent Cruise Control (ICC) system
ON indicator .....................................................
...
2-27
Intelligent Key ....................................................
...
3-2
Intelligent Key system ........................................
...
3-6
Battery replacement ...................................
...
8-28
Key operating range .....................................
...
3-8
Key operation .............................................
...
3-10
Warning signals .........................................
...
3-14
Intercooler cooling system .................................
...
8-9
Interior light control switch ..............................
...
2-60
Interior light replacement .................................
...
8-31
Interior lights ...................................................
...
2-60
Interior trunk lid release ...................................
...
3-25
ISOFIX child restraint ........................................
...
1-23
J
Jump starting ...................................................
...
6-10
K
Keyless entry (See remote keyless
entry system) ...................................................
...
3-16
Keys ...................................................................
...
3-2
For Intelligent Key system ............................
...
3-6
L
Labels
Air bag warning labels ...............................
...
1-57
Air conditioner specification label ............
...
10-14
Emission control information label ...........
...
10-14
Engine serial number ...............................
...
10-13
F.M.V.S.S./C.M.V.S.S. certification label .....
... 10-13
Tire and Loading information label ...
... 8-35, 10-14
Vehicle identification number (VIN) ...........
...
10-12
Lane Departure Warning (LDW) /Lane Departure
Prevention (LDP) ...............................................
...
5-35
LATCH system ...................................................
...
1-23
License plate
Installing front license plate .....................
...
10-15
Light
Air bag warning light ..................................
...
1-58
Bulb replacement .......................................
...
8-30
Fog light switch ..........................................
...
2-47
Headlight switch ........................................
...
2-40
Indicator lights ...........................................
...
2-18
Interior light control switch ........................
...
2-60
Interior lights .............................................
...
2-60
Map lights ..................................................
...
2-60
Replacement ..............................................
...
8-30
Trunk light .................................................
...
2-62
Vanity mirror lights ....................................
...
2-61
Warning/indicator lights and
audible reminders ......................................
...
2-12
Lights
Exterior and interior light replacement .......
...
8-31
Loading information (See vehicle
loading information) .......................................
...
10-16
Lock
Automatic door locks ....................................
...
3-6
Door locks ....................................................
...
3-4
Power door lock ...........................................
...
3-4
Trunk lid ......................................................
...
3-23
Locking with mechanical key ..............................
...
3-4
Log-in function .................................................
...
3-16
Loose Fuel Cap warning ...........................
...
2-25, 3-28
Low fuel warning light ......................................
...
2-14
Low outside temperature warning .....................
...
2-26
Low tire pressure warning light ........................
...
2-14
Low tire pressure warning system
(See Tire Pressure Monitoring
System (TPMS)) ..................................
...
5-5, 6-3, 8-33
M
Maintenance
Battery .......................................................
...
8-17
General maintenance ....................................
...
9-2
Indicators for maintenance (vehicle
information display) ...................................
...
2-28
Inside the vehicle ..........................................
...
9-3
Maintenance log .........................................
...
9-18
Maintenance precautions .............................
...
8-3
Maintenance requirements ............................
...
9-2
Maintenance schedules .................................
...
9-7
Maintenance under severe
driving conditions .......................................
...
9-17
Outside the vehicle .......................................
...
9-2
Seat belt maintenance ...............................
...
1-18
Standard maintenance ..................................
...
9-8
Under the hood and vehicle ..........................
...
9-4
Malfunction indicator light (MIL) .......................
...
2-19
Map lights ........................................................
...
2-60
Master warning light ........................................
...
2-16
11-4
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(457,1)
Mechanical key (Intelligent Key system) .............
...
3-3
Memory storage
Automatic drive positioner ...........................
...
3-33
Meter
Trip computer .............................................
...
2-31
Meters and gauges .............................................
...
2-6
Instrument brightness control ....................
...
2-46
Mirror
Inside mirror ...............................................
...
3-30
Outside mirrors ...........................................
...
3-31
Vanity mirror ...............................................
...
3-33
Moonroof .........................................................
...
2-58
N
NAVI Shift Control ............................................
...
5-21
New vehicle break-in ......................................
...
5-125
O
Odometer ...........................................................
...
2-7
Off-road recovery ...............................................
...
5-9
Oil
Capacities and
recommended fluids/lubricants ..................
...
10-2
Changing engine oil and filter ....................
...
8-11
Checking engine oil level ............................
...
8-11
Engine oil ...................................................
...
8-10
One touch unlock sensor (See Intelligent
Key system) .....................................................
...
3-10
Operation
Indicators for operation ..............................
...
2-24
Outside air temperature ...................................
...
2-34
Outside mirrors ................................................
...
3-31
Overheat, If your vehicle overheats ..................
...
6-16
Owner’s Manual/Service Manual
order information ...........................................
...
10-24
P
Panic alarm ......................................................
...
3-18
Parking
Parking brake operation ..............................
...
5-22
Parking on hills .........................................
...
5-129
Parking brake break-in ...................................
...
5-134
PERSONAL mode ..............................................
...
5-26
Phone
Car phone or CB radio ..................................
...
4-3
Power
Power door lock ...........................................
...
3-4
Power outlet ...............................................
...
2-50
Power steering fluid ...................................
...
8-14
Power steering system ..............................
...
5-130
Power windows ..........................................
...
2-55
Power moonroof ...............................................
...
2-58
Power steering warning light ............................
...
2-16
Precautions
Braking precautions ..................................
...
5-133
Child restraints ..........................................
...
1-21
Cruise control ..............................................
...
5-74
Maintenance ................................................
...
8-3
Seat belt usage ..........................................
...
1-11
Supplemental restraint system ...................
...
1-40
When starting and driving ............................
...
5-4
Pre-crash seat belts with comfort function ........
...
1-14
Predictive Forward Collision Warning (PFCW) ...
... 5-116
Push starting ...................................................
...
6-16
Push-button ignition switch ..............................
...
5-12
R
Radio
Car phone or CB radio ..................................
...
4-3
Rain-sensing auto wiper system .......................
...
2-39
Rapid air pressure loss ....................................
...
5-10
Readiness for inspection/maintenance (I/M)
test (US only) .................................................
...
10-22
Rear seats ..........................................................
...
1-6
Rear window and outside mirror
defroster switch ...............................................
...
2-40
Recorders
Event data ................................................
...
10-23
Registering your vehicle in another country ....
... 10-12
Remote engine start .........................................
...
3-20
Remote keyless entry system ...........................
...
3-16
Reporting safety defects .................................
...
10-21
Request switch (See Intelligent Key system) .....
... 3-10
Roadside assistance program .............................
...
6-2
Rollover ..............................................................
...
5-9
Roof
Moonroof ...................................................
...
2-58
Run-flat tires ......................................................
...
6-4
11-5
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(458,1)
S
Safety
Child seat belts ..........................................
...
1-18
Reporting safety defects ...........................
...
10-21
Seat adjustment
Front power seat adjustment ........................
...
1-3
Front seats ...................................................
...
1-3
Seat belt(s)
Child safety ................................................
...
1-18
Infants .......................................................
...
1-19
Injured persons ..........................................
...
1-14
Larger children ...........................................
...
1-19
Precautions on seat belt usage ...................
...
1-11
Pre-crash seat belts with comfort function ...
... 1-14
Pregnant women ........................................
...
1-13
Seat belt cleaning .........................................
...
7-7
Seat belt extenders ....................................
...
1-17
Seat belt maintenance ...............................
...
1-18
Seat belt warning light and chime ..............
...
2-17
Seat belts ..................................................
...
1-11
Seat belts with pretensioners .....................
...
1-56
Small children ............................................
...
1-19
Three-point type .........................................
...
1-14
Seat(s)
Driver-side memory .....................................
...
3-33
Heated seats ..............................................
...
2-48
Seats ...........................................................
...
1-2
Security system
Vehicle security system ..............................
...
2-35
Security system (INFINITI Vehicle Immobilizer
System)
Engine start ...............................................
...
2-36
Shift lever
Shift lock release ........................................
...
5-20
Shift lock release, Transmission .......................
...
5-20
Shifting
Automatic Transmission (AT) .......................
...
5-16
SNOW mode .....................................................
...
5-24
Spare tire .......................................................
...
10-11
Spark plugs .....................................................
...
8-21
Speedometer ......................................................
...
2-7
SPORT mode ....................................................
...
5-24
SPORT+ mode ..................................................
...
5-23
Standard maintenance .......................................
...
9-8
STANDARD mode ..............................................
...
5-23
Starting
Before starting the engine ..........................
...
5-15
Jump starting .............................................
...
8-20
Precautions when starting and driving ..........
...
5-4
Push starting .............................................
...
6-16
Starting the engine ....................................
...
5-15
Status light, Front passenger air bag ................
...
1-48
Steering
Direct Adaptive Steering ............................
...
5-131
Heated steering wheel ................................
...
2-49
Power steering fluid ...................................
...
8-14
Power steering system ..............................
...
5-130
Tilt/telescopic steering ................................
...
3-28
Storage ............................................................
...
2-51
Storage box .....................................................
...
2-54
Sun visors ........................................................
...
3-29
Sunglasses holder ............................................
...
2-52
Supplemental air bag warning labels ...............
...
1-57
Supplemental air bag warning light .........
...
1-58, 2-17
Supplemental restraint system .........................
...
1-40
Precautions on supplemental
restraint system .........................................
...
1-40
Switch
Autolight switch .........................................
...
2-41
Fog light switch ..........................................
...
2-47
Hazard warning flasher switch ......................
...
6-2
Headlight switch ........................................
...
2-40
Power door lock switch ................................
...
3-5
Push-button ignition switch ........................
...
5-12
Rear window and outside mirror
defroster switch .........................................
...
2-40
Turn signal switch ......................................
...
2-46
Vehicle Dynamic Control (VDC) off switch ....
... 2-47
T
Tachometer ........................................................
...
2-8
Temperature gauge
Engine coolant temperature gauge ...............
...
2-8
Theft (INFINITI Vehicle Immobilizer System)
Engine start ...............................................
...
2-36
Three-way catalyst .............................................
...
5-5
Tilt/telescopic steering .....................................
...
3-28
Tire
Flat Tire - Visit dealer warning ....................
...
2-25
Run-flat tires ................................................
...
6-4
Tire replacement indicator ..........................
...
2-28
11-6
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(459,1)
Tire rotation ...............................................
...
8-42
Tire pressure
Low tire pressure warning light ..................
...
2-14
Tire Pressure Low - Add Air warning .................
...
2-25
Tires
Flat tire ........................................................
...
6-3
Low tire pressure
warning system ............................
...
5-5, 6-3, 8-33
Run-flat tires ..............................................
...
8-40
Spare tire ...................................................
...
8-46
Tire and Loading information label ...
... 8-35, 10-14
Tire chains .................................................
...
8-41
Tire dressing ................................................
...
7-4
Tire pressure ..............................................
...
8-33
Tire Pressure Monitoring
System (TPMS) .............................
...
5-5, 6-3, 8-33
Types of tires .............................................
...
8-39
Uniform tire quality grading .....................
...
10-20
Wheel/tire size .........................................
...
10-11
Wheels and tires ........................................
...
8-33
Towing
Flat towing ...............................................
...
10-19
Tow truck towing ........................................
...
6-17
Towing a trailer ........................................
...
10-19
TPMS
Tire Pressure Monitoring System ... 5-5, 6-3, 8-33
TPMS, Tire pressure monitoring system
TPMS with Tire Inflation Indicator .................
...
5-8
Trailer towing .................................................
...
10-19
Transceiver
HomeLink® Universal Transceiver ...............
...
2-62
Transmission
Automatic Transmission Fluid (ATF) .............
...
8-14
Driving with Automatic Transmission (AT) ... 5-16
Transmission shift lever lock release ...........
...
5-20
Transmitter (See remote keyless
entry system) ...................................................
...
3-16
Traveling or registering in another country .....
... 10-12
Trip computer ...................................................
...
2-31
Trip odometer ...................................................
...
2-31
Trunk
Interior trunk lid release ..............................
...
3-25
Light ..........................................................
...
2-62
Trunk hooks ...............................................
...
2-54
Trunk lid ......................................................
...
3-23
Trunk lid release switch ...............................
...
3-24
Trunk open request switch ..........................
...
3-24
Trunk release power cancel switch ..............
...
3-25
Turn signal switch ............................................
...
2-46
U
Underbody cleaning ...........................................
...
7-3
Uniform tire quality grading ...........................
...
10-20
V
Vanity mirror ....................................................
...
3-33
Vanity mirror lights ..........................................
...
2-61
Variable voltage control system ........................
...
8-20
Vehicle
Dimensions ..............................................
...
10-11
Recovery (freeing a stuck vehicle) ...............
...
6-19
Vehicle Dynamic Control (VDC) off switch ....
... 2-47
Vehicle Dynamic Control (VDC) system .......
... 5-136
Vehicle Dynamic Control (VDC)
warning light ..............................................
...
2-18
Vehicle identification number (VIN) .................
...
10-12
Vehicle information display ..............................
...
2-21
Vehicle loading information ............................
...
10-16
Vehicle security system ....................................
...
2-35
Ventilators .........................................................
...
4-2
W
Walk-in mechanism ............................................
...
1-5
Warning
Flat Tire - Visit dealer warning ....................
...
2-25
Hazard warning flasher switch ......................
...
6-2
Indicators for operation (vehicle
information display) ...................................
...
2-24
Lights .........................................................
...
2-12
Power steering warning light ......................
...
2-16
Predictive Forward Collision
Warning (PFCW) .........................................
...
5-116
Tire Pressure Monitoring
System (TPMS) .............................
...
5-5, 6-3, 8-33
Vehicle information display ........................
...
2-21
Warning lights, indicator lights and
audible reminders ......................................
...
2-12
Warning labels
Air bag warning labels ...............................
...
1-57
Warning light
Air bag warning light .........................
...
1-58, 2-17
11-7
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(460,1)
Anti-lock braking system (ABS)
warning light ..............................................
...
2-12
Brake warning light ....................................
...
2-13
Forward Emergency Braking (FEB) system
warning light ..............................................
...
2-14
Low fuel warning light ................................
...
2-14
Low tire pressure warning light ..................
...
2-14
Seat belt warning light and chime ..............
...
2-17
Warranty
Emission control system warranty ............
...
10-21
Washer switch
Wiper and washer switch ...........................
...
2-37
Washing .............................................................
...
7-2
Waxing ...............................................................
...
7-2
Welcome light and farewell light function .........
...
3-11
Wheel/tire size ...............................................
...
10-11
Wheels and tires ..............................................
...
8-33
Care of wheels ..............................................
...
7-3
Cleaning aluminum alloy wheels ...................
...
7-3
Cleaning bright wheels .................................
...
7-4
Window washer fluid ........................................
...
8-16
Window(s)
Automatic adjusting function ......................
...
2-57
Cleaning ........................................................
...
7-3
Power windows ..........................................
...
2-55
Wiper
Rain-sensing auto wiper system .................
...
2-39
Wiper and washer switch ...........................
...
2-37
Wiper blades ..............................................
...
8-23
Wiper and washer switch .................................
...
2-37
11-8
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(463,1)
Gas station information
GAS STATION INFORMATION
CV37D1-77182AA9-EA34-4B9F-9424-2BDD77048A91
FUEL INFORMATION
CV37D1-20F78A46-E02E-45F7-818F-747D8C0C7324
Use unleaded premium gasoline with an
octane rating of at least 91 AKI (Anti-Knock
Index) number (Research octane number
96).
VR30DDTT engine model: INFINITI recommends the use of unleaded premium
gasoline with 93 AKI (Anti-Knock Index)
number (Research octane number 98) to
obtain the maximum vehicle performance
and the best driveability.
.
Condition:
Using a fuel other than that specified
could adversely affect the emission
control system, and may also affect
warranty coverage.
.
Under no circumstances should a leaded
gasoline be used, because this will
damage the three-way catalyst.
.
Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed to
run on E-15 or E-85 fuel. Using E-15 or E85 fuel in a vehicle not specifically
designed for E-15 or E-85 fuel can
adversely affect the emission control
devices and systems of the vehicle.
Damage caused by such fuel is not
covered by the INFINITI new vehicle
limited warranty.
If unleaded premium gasoline is not available, unleaded regular gasoline with an
octane rating of at least 87 AKI number
(Research octane number 91) may be
temporarily used, but only under the
following precautions:
. Have the fuel tank filled only partially
with unleaded regular gasoline, and fill
up with unleaded premium gasoline as
soon as possible.
. Avoid full throttle driving and abrupt
acceleration.
Use unleaded premium gasoline for maximum vehicle performance.
have to consult your gasoline retailer for
more details. Note that Federal and
California laws prohibit the use of MMT
in reformulated gasoline.
CAUTION
.
Do not use fuel that contains the octane
booster methylcyclopentadienyl manganese tricarbonyl (MMT). Using fuel containing MMT may adversely affect
vehicle performance and vehicle emissions. Not all fuel dispensers are labeled
to indicate MMT content, so you may
[ Edit: 2016/ 4/ 27
.
U.S. government regulations require
ethanol dispensing pumps to be identified by a small, square, orange and black
label with the common abbreviation or
the appropriate percentage for that
region.
ENGINE OIL
RECOMMENDATION:
CV37D1-BC054C72-B5F6-42F7-B23F-835799447376
VR30DDTTCV37D1-F8B161E6-4144-4D86-8577-D97BED063990
engine model
. Genuine NISSAN engine oil or equivalent
. Engine oil with API Certification Mark,
Viscosity SAE 0W-20
2.0L turboCV37D1-E800DEC1-AC45-4887-9388-B7C8101A4F21
gasoline engine model
. Engine oil meeting specification
MB229.5, Viscosity SAE 0W-30 or
equivalent
See “Capacities and recommended fluids/
lubricants” (P.10-2) for engine oil and oil
filter recommendation.
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
(464,1)
COLD TIRECV37D1-80309D34-1510-491E-8765-D8D84150C0CB
PRESSURES:
The label is typically located on the driver
side center pillar or on the driver’s door.
For additional information, see “Wheels
and tires” (P.8-33).
NEW VEHICLE BREAK-IN PROCEDURES RECOMMENDATION:
CV37D1-DEEA300A-3422-4130-A221-4C6802CDFB40
During the first 1,200 miles (2,000 km) of
vehicle use, follow the recommendations
outlined in the “Break-in schedule” (P.5125) of this Owner’s Manual. Follow these
recommendations for the future reliability
and economy of your new vehicle.
Condition:
[ Edit: 2016/ 4/ 27
Model: 2017MY INFINITI Q60(CV37) OM17E0CV37U0 ]
Printing: June 2016 (01) / OM17E0 CV37U0 / Printed in U.S.A.
2017 Infiniti Q60
For your safety, read carefully and keep in this vehicle.
2017 Infiniti Q60
Owner’s Manual and
Maintenance Information
Download PDF

advertising